J une 2012 WP-17

Signature Core Fiber

Optic Cabling System

Multimode Fiber: Understanding Chromatic
Dispersion




White Paper

WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
2
Multimode Fiber: Understanding Chromatic Dispersion
Introduction
The performance and reliability of networks within the Data Center are vital to the operation of todays Enterprise.
As the performance requirements of these networks have advanced to keep up with the data and virtualization
explosion, the specifications on the constituent components have also become more demanding. For high-speed
optical networks using laser-optimized multimode fiber (MMF) operating at 10 Gb/s today and 40 and 100 Gb/s in
the near future, it is more critical than ever for network operators and designers to have an accurate knowledge of
the performance specifications of the active and passive fiber optic components used to make up the network.

Traditionally, much of the focus on the performance of passive fiber optic components has been on the overall
optical power loss or attenuation of the fiber cable and connectors. Although loss is a critical parameter for the fiber
cable and connectivity, signal impairment related to the fiber bandwidth is also critically important for networks
operating at gigabit data rates and above. Traditional techniques of minimizing signal impairments by minimizing the
total dispersion have been built upon simplified system models that do not consider the interaction of the two
primary types of dispersion in MMF networks: modal dispersion and chromatic dispersion. Panduit has developed
an advancement in MMF communications systems that compensates for both modal and chromatic dispersion,
delivering extended reach over OM4 MMF beyond industry standards to deliver verified system performance and
signal integrity as well as design flexibility.

This white paper investigates the benefits of deploying Panduits Signature Core Fiber Optic Cabling System in
Data Centers, Enterprise, and Factory Automation. After a review of singlemode and MMF, fiber bandwidth, and the
role of bandwidth in chromatic dispersion, this paper explores the comparison between modal dispersion and
chromatic dispersion. Finally, this paper demonstrates how Panduits Signature Core Fiber Optic Cabling System
can help compensate for the two types of dispersion, solving the problem of poor correlation between fiber
bandwidth and system performance in much of todays laser-optimized MMF.

Singlemode Fiber versus Multimode Fiber
A singlemode optical fiber is an optical fiber that carries a single ray (mode) of light transmission. A mode is the
path the laser light travels down the fiber. For singlemode optical fiber, the fiber has a small core diameter which
only allows one mode. With only one mode, the signal is free of distortion and therefore the fiber optic medium has
extremely long reach; as such, singlemode fiber is used for high speed signal transmission over long distances.

MMF is optical fiber with a larger core than singlemode fiber and is designed to carry multiple light rays, or modes,
simultaneously, each mode positioned at a slightly different reflection angle within the fiber core. For MMF, the light
can take several paths at once. The larger MMF core makes it easy to capture light from a transceiver and to guide
multiple modes at the same time, making it a cost effective alternative to singlemode fiber over shorter distances.
MMF speeds up the modes traveling the longer paths and keeps the individual modes (pulses) aligned to reduce
the effect of modal dispersion. Even though MMF today corrects for modal dispersion, MMF is used typically for
short distances because the modes will still have a tendency to separate over longer lengths regardless of the
modal dispersion compensation.

Singlemode optical fiber is good for long runs in Data Centers, for example, from the Data Center to
telecommunications closets, and can be used to connect buildings on a campus and for telecommunications and
cable systems. However, singlemode fiber has a smaller core than MMF, which makes it more difficult to use; also,

WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
3
Multimode Fiber: Understanding Chromatic Dispersion
tighter mechanical tolerances of connectors are associated with singlemode fiber, and the alignment of laser and
lens mechanism is more challenging. These differences increase the cost of a singlemode link to two to three times
the cost of a multimode link. MMF is ideal for use within Data Centers because the medium addresses specific
network challenges such as limited space, tight bends, short distances, and low cost.

Fiber Bandwidth
Fiber bandwidth is a quantitative measure of how well the medium is able to support a given data transmission rate
over a specified distance. Fiber with a higher bandwidth is able to support higher data rates over a longer distance
than a fiber with a lower bandwidth. To illustrate the importance of fiber bandwidth, the most important (largest)
power penalties for 10 Gb/s Ethernet networks that extend 300m are shown in Figure 1. [1] The intersymbol
interference (ISI) power penalty, which is strongly related to the fiber bandwidth, is greater than both the connectors
and splices power penalty and fiber attenuation power penalty combined.

Figure 1. This figure illustrates the largest power penalties for 10 Gb/s Ethernet optical links that extend
300 m (10GBASE-SR). [1]
Fiber bandwidth is impacted by two factors: fiber attenuation and dispersion. In communication systems that utilize
MMF optic transceivers, information (data) is carried by light pulses generated by a laser transmitter called a
Vertical Cavity Surface Emitting Laser (VCSEL), which is focused into the MMF. These lasers convert the electrical
signals into laser light. As these light pulses travel through the fiber, the light lost at the connectors and from the
attenuation of the fiber cable reduces the amplitude of the original signal and impairs the receivers ability to
reconstruct the transmitted data. Ultimately this causes bit-errors and degrades the performance of the network. A
bit error is where the receiver incorrectly interprets the received data bit; if a one was sent; the receiver interpreted
it as a zero and vice-versa if a zero was sent.

Another system impairment, called dispersion, is the spreading out of light pulses in time which also degrades the
original transmitted signal and may cause errors as well. Two types of dispersion exist, modal and chromatic;
however, traditional laser-optimized MMF deployments are designed to minimize only one cause of dispersion:
modal dispersion.


0
0.5
1
1.5
2
2.5
3
ISI (Fiber
Bandwidth)
Connectors &
Splices
Fiber Attenuation Other Margin
P
o
w
e
r

P
e
n
a
l
t
y

M
a
g
n
i
t
u
d
e

(
d
B
)


WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
4
Multimode Fiber: Understanding Chromatic Dispersion
Modal Dispersion
The amount of light spreading in time based on the different modes taken is called modal dispersion and is
measured for every laser-optimized multimode fiber with Effective Modal Bandwidth (EMB) and/or Differential Mode
Delay (DMD) measurements (see Figure 2a). In MMF, light pulses travel through the fiber in discrete paths, or
modes, which have slightly different path lengths. In order for the pulses of light to arrive at the receiver at the same
time, which is necessary for the signal to be reconstructed properly, the light traveling in the modes that have a
longer path length (higher order modes) must travel faster than the light traveling in the modes that have a shorter
path length (lower order modes).

This mode and speed balancing, or simply speeding up and slowing down of the different components of the light
pulse, is done by grading the refractive index of MMF and has been a primary focus of design and manufacturing
improvements for more than 20 years. However, small imperfections are unavoidable in the manufacturing process
and cause the light to have slightly unequal transit times for all the different modes. The increasingly stringent
requirements on the maximum amount of modal dispersion, or minimum effective modal bandwidth, are defined
within the fiber standards documents for the various classes of laser-optimized MMF: OM3 (EMB 2000 MHzkm)
and OM4 (EMB 4700 MHzkm).

Chromatic Dispersion
The other type of dispersion important in MMF communication systems is the spreading out of light due to the
slightly different colors or wavelengths of light that make up the optical signal. This type of dispersion is called
chromatic dispersion. Light generated from typical VCSELs is actually not a single wavelength but is made up of
several closely spaced discrete wavelengths around 850 nm.
1
The speed at which the light travels through the fiber
depends on the wavelength, therefore the individual wavelength components of the light pulse travel at slightly
different speeds with the shorter wavelengths traveling at slower speeds compared to the longer wavelengths.

This slight difference in the speed that the various wavelengths travel through the fiber results in unequal transit
times, which results in signal distortion. The wavelengths cause the laser pulse to spread out which makes it harder
to interpret the data stream at the receiving end and limits reach while increasing Bit Error Rate (BER). The concern
for chromatic dispersion increases as the speed of the data rate increases. Chromatic dispersion effects are even
more important to control at higher data rates because the difference in transit times and chromatic dispersion is
proportional to the difference in wavelengths emitted by the VCSEL, and the limitations on the spectral widths of
VCSELs increased from 10 Gb/s Ethernet to 40/100 Gb/s Ethernet (see Figure 2b).
2
[2]


VCSEL to Fiber Coupling
While exploring the causes of dispersion in order to develop a fiber optic cabling system that minimizes both modal
and chromatic dispersion, Panduit researchers discovered that there is a radial-dependent wavelength that couples
into MMF. This coupling ultimately results in a radial dependence of both modal and chromatic dispersion.


1
VCSELs typically utilized in short reach communications systems have fiber coupled emission spectrums that are
multimode and have RMS spectral widths >0.1 nm.

2
IEEE 802.3

2008 and IEEE 802.3ba

2010 specify the RMS spectral width for 10GBASE-SR transmitters

<0.45 nm and the RMS spectral width for 40/100GBASE-SR4/10 transmitters <0.65 nm.

WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
5
Multimode Fiber: Understanding Chromatic Dispersion

2a) pulse spread from modal dispersion 2b) pulse spread from chromatic dispersion
Figure 2. Simplified representation of 2a) modal dispersion and 2b) chromatic dispersion in MMF.
In 2a) only two different fiber modes are shown. The path length of mode 2 is greater than mode 1 so the
light in mode 2 must travel faster than mode 1 to arrive at the end of the fiber at the same time as mode 1.
The spreading out of light signals, t, due to path length differences is called modal dispersion.
In 2b) only two wavelengths, 1 and 2, where 1 < 2, are shown passing through the fiber in mode 2.
Because shorter wavelengths travel slower than longer wavelengths, 2 arrives at the end of the fiber
before 1. The spreading out of lights signals, t, due to their wavelengths is called chromatic dispersion.

The basic configuration of a typical VCSEL Transmitter Optical Sub-Assembly (TOSA) used in multimode
transceivers is shown in Figure 3. The optical sub-assembly couples light emitted from the VCSEL into the MMF
using a lens and precise optical alignment between the VCSEL, lens and fiber. The light emission characteristics of
VCSELs are known to emit longer wavelengths with small angles and shorter wavelengths at larger angles (from
the optical axis). [3] Consequently, the TOSA will generally couple longer wavelengths into fiber modes near the
center of the fiber core with shorter path lengths (lower order modes). It will also couple shorter wavelengths
emitted into larger angles that emit into fiber modes nearer the edges of the fiber core with longer path lengths
(higher order modes). The following section describes how these findings were incorporated into the Panduit
Signature Core Fiber Optic Cabling System.

Figure 3. Transmitter Optical Sub-Assembly (TOSA) showing the spectral dependant coupling from VCSEL
to MMF, where longer wavelengths are coupled into the lower order modes while the shorter wavelengths
are coupled into the higher order modes.

WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
6
Multimode Fiber: Understanding Chromatic Dispersion
Compensating Modal and Chromatic Dispersion
Shorter wavelengths travel slower than longer wavelengths and this speed difference needs to be corrected or
compensated in order for the total light pulse to arrive at the receiver at the same time. Since the shorter
wavelengths are coupled towards the edge of the fiber, this compensation may be performed by intentionally
speeding up the modes at the extremities of the fiber. Therefore the difference in speed due to the various colors of
the light (chromatic dispersion) may be effectively compensated by a difference in speed of the different modes
(modal dispersion). This is the basic concept behind Panduits Signature Core Fiber Optic Cabling System, which
has been specifically designed to compensate for both modal and chromatic dispersion, providing the highest
system performance.

Although the effects of modal dispersion and chromatic dispersion are well understood, traditional systems models
oversimplify their interaction and therefore do not correctly account for how these two effects may add or subtract
from one another. Traditional laser-optimized MMF is designed to only minimize the effects of modal dispersion,
thus ignoring the effects of chromatic dispersion. However, because VCSELs preferentially couple different
wavelength components into different areas of the fiber, improved system performance is achieved by designing the
fiber to balance or reduce the effects of chromatic dispersion with some amount of modal dispersion.

It is important to understand why these effects must be considered together rather than separately. For example,
consider a hypothetical fiber that supports only two modes where one of the modes has a longer path length than
the other and an optical signal that consists of two different wavelengths where one wavelength is longer than the
other (remembering that shorter wavelengths travel slower than longer wavelengths in normal fibers). In this
simplified situation there can only be two different combinations of modes and wavelengths. The first is when the
shorter wavelength light travels through the longer path length mode. Consequently, this part of the optical signal
will take much longer to pass through the fiber than the part of the signal comprised of the longer wavelength that
takes the shorter path length mode. In the other combination the shorter wavelength light travels through the mode
with the shorter path length and the longer wavelength light travels through the mode with a longer path length. In
this later case, the light that travels faster must travel a longer path length and may be designed to have a similar
arrival time as the light that travels a bit slower, but takes a shorter path length.

From this simplified example, it is easy to understand how these chromatic and modal effects must be considered
together because they only influence the velocity of the light pulse as it passes through the fiber. However, the fiber
coupled wavelength distribution of VCSEL TOSAs was not considered within systems models only the magnitude
of their effects was considered. Therefore, these models are not able to predict how modal and chromatic effects
may be combined to reduce the total dispersion which will provide improved system performance. These models
also are unable to predict how modal and chromatic effects may be added together, which will increase the total
dispersion and significantly degrade system performance more than traditional systems models.

Although the simplified example used above is useful for illustrative purposes, the large number of VCSEL
wavelength components that make up the light signal (~20), their fiber coupled distribution, and the large number of
fiber modes (~400) make the analysis of a real transceiver and fiber combination quite involved. Detailed
simulations of thousands of VCSEL transceivers and fiber combinations have been computed to optimize the
design of Panduits Signature Core Fiber Optic Cabling System and quantify the benefits of compensating modal
and chromatic dispersion.

WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
7
Multimode Fiber: Understanding Chromatic Dispersion
Panduits Signature Core Fiber Optic Cabling System is a standards compliant advanced fiber optic cabling
system that counterbalances the dispersive effects of both modal dispersion and chromatic dispersion, therefore
minimizing total dispersion. The system delivers signal integrity far beyond the requirements for 10/40/100 Gb/s
Ethernet, and 8 and 16 Gb/s Fibre Channel, providing the ultimate in design flexibility which allows implementation
of complex Data Center architectures, and verified optical performance. It improves MMF performance by
increasing modal bandwidth. In addition, Panduits Signature Core Fiber Optic Cabling System ensures
consistent performance and reliability of critical systems, delivering the ability to deploy more connectors in the
channel, which simplifies moves, adds and changes.

Figure 4 shows the benefits delivered by Panduits Signature Core Fiber Optic Cabling System fiber, as
compared to traditional MMF that does not compensate for modal and chromatic dispersion. The average
improvement Panduits Signature Core Fiber Optic Cabling System provides is 30% compared to the bandwidth
of traditional multimode fiber. This improved bandwidth can be used to provide greater reach, or add more
connectivity, or realize improved system performance (lower bit-error-ratios) for 10G, 40G, and 100G MMF systems.


Figure 4. Modeled benefit, in terms of bandwidth ratio of Panduits Signature Core Fiber Optic Cabling
System compared to traditional MMF that does not compensate modal and chromatic dispersion.
The bandwidth ratio is the bandwidth calculated considering modal and chromatic dispersion collectively
divided by the traditional modal bandwidth. Bandwidth ratios >100% represent an improvement and
bandwidth ratios <100% represent a degradation. Improvements or degradations in bandwidth will improve
or degrade system performance compared to the performance that traditional system models predict.
Panduits Signature Core Fiber Optic Cabling System provides improved system performance for
approximately 98% of transceivers with an average improvement of 30%. The 2% balance of these
transceivers incurs a bandwidth degradation of about 1%.
0%
2%
4%
6%
8%
10%
12%
50% 75% 100% 125% 150% 175% 200% 225% 250%
F
r
e
q
u
e
n
c
y

Bandwidth Ratio
Traditional MMF Signature Core MMF

WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
8
Multimode Fiber: Understanding Chromatic Dispersion
Conversely, traditional fiber realizes a reduction in bandwidth by approximately 20% compared to the bandwidth
predicted by traditional models that do not collectively consider the effects of model and chromatic dispersion. This
reduction in bandwidth has the dangerous effect of reducing the reach, connectivity budget and system
performance.

Another way to take advantage of Signature Cores enhanced performance is with the deployment of a fabric
based switching architecture. By using the Signature Core Fiber Optic Cabling System to connect the leaf and
spine switches, the fabric architecture can be enlarged to cover more area within the data center.

Conclusion
For high-speed Data Center and Enterprise optical communication networks, basic optical loss and dispersion the
spreading out of optical signals are the most important factors that will determine overall network performance.
Utilizing high performance (low loss) connectivity and fiber cable as well as following industry standardized
practices of cable routing (e.g. maintaining bend radius control) are the best ways to minimize signal impairments
from excessive optical loss. Traditional techniques of minimizing signal impairments by reducing the total dispersion
have been built upon simplified system models that do not consider the interaction of the two primary types of
dispersion in MMF networks: modal dispersion and chromatic dispersion. The net effect is that these simplified
systems models do not accurately provide a worst case estimate of network performance as they were intended,
and the transceiver and fiber have been optimized independently, thereby ignoring potential performance
improvements by designing them as a system.

By considering both modal and chromatic dispersion together, customers can experience significant improvements
which result in a better system model that can more accurately predict performance. Panduits Signature Core
Fiber Optic Cabling System fiber was designed to account for the interaction of modal and chromatic dispersion and
compensate for these effects to provide a communication system (transceiver and fiber combination) with minimum
total dispersion. This system provides the best of both performance improvements by compensating modal and
chromatic effects while simultaneously eliminating the potential combination of chromatic and modal dispersion,
which can cause a significantly degraded system performance.

Panduits Signature Core Fiber Optic Cabling System is the only MMF to correct modal and chromatic dispersion
because it is designed to counterbalance both of these dispersive effects and therefore minimize total dispersion.
This fiber is 100% OM3 and/or OM4 standards compliant and therefore fully backwards compatible with all other
standards compliant laser-optimized OM3 and OM4 cable.[4,5] For those channels that are the most demanding in
terms of reach, connectivity budget or performance requirements, Panduits Signature Core Fiber Optic Cabling
System MMF provides network designers and operators with the highest performance fiber available to meet the
most demanding applications and Data Center architectures.




WW-CPWP-17, Rev.0, 06/2012
2012 Panduit Corp. All rights reserved.
9
Multimode Fiber: Understanding Chromatic Dispersion
References

[1] IEEE Std 802.3 - 2008.

[2] IEEE Std 802.3ba - 2010.

[3] S. Gronenborna, H. Moenchb, M. Millerc, P. Gerlachc, and J . Kolbb, Dynamics of the Angular Emission
Spectrum of Large-area VCSELs,Vertical-Cavity Surface-Emitting Lasers XIV, SPIE Proc., vol. 7615, pp.
76150I-76150I-12 (2010).

[4] TIA-492AAAC-B, Telecommunications Industry Association standard Detail specification for 850-nm
laser-optimized, 50-m core diameter/125-m cladding diameter class 1a graded-index multimode optical
fibers,November 2009.

[5] TIA-492AAAD, Telecommunications Industry Association standard Detail specification for 850-nm
laser-optimized, 50-m core diameter/125-m cladding diameter class 1a graded-index multimode optical
fibers suitable for manufacturing OM$ cabled optical fiber,September 2009.



About Panduit
Panduit is a world-class developer and provider of leading-edge solutions that help customers optimize the physical
infrastructure through simplification, increased agility and operational efficiency. Panduits Unified Physical
Infrastructure (UPI) based solutions give enterprises the capabilities to connect, manage and automate
communications, computing, power, control and security systems for a smarter, unified business foundation.
Panduit provides flexible, end-to-end solutions tailored by application and industry to drive performance, operational
and financial advantages. Panduits global manufacturing, logistics, and e-commerce capabilities along with a global
network of distribution partners help customers reduce supply chain risk. Strong technology relationships with
industry leading systems vendors and an engaged partner ecosystem of consultants, integrators and contractors
together with its global staff and unmatched service and support make Panduit a valuable and trusted partner.

www.panduit.com [email protected]