74HC175
74HC175
74HC175
M74HC175
October 1992
QUAD D-TYPE FLIP-FLOPWITH CLEAR
B1R
(Plastic Package)
ORDER CODES :
M54HC175F1R M74HC175M1R
M74HC175B1R M74HC175C1R
F1R
(Ceramic Package)
M1R
(Micro Package)
C1R
(Chip Carrier)
PIN CONNECTIONS(top view)
NC =
No Internal
Connection
DESCRIPTION
.HIGH SPEED
tPD = 13 ns (TYP.) AT VCC = 5 V
.LOWPOWER DISSIPATION
I
CC
= 4 A(MAX.) AT T
A
= 25 C
.HIGH NOISEIMMUNITY
VNIH = VNIL = 28 % VCC (MIN.)
.OUTPUT DRIVE CAPABILITY
10 LSTTL LOADS
.SYMMETRICAL OUTPUT IMPEDANCE
|IOH| = IOL = 4 mA (MIN.)
.BALANCEDPROPAGATION DELAYS
t
PLH
= t
PHL
.WIDE OPERATING VOLTAGE RANGE
VCC (OPR) = 2 V TO6 V
.PIN ANDFUNCTION COMPATIBLE
WITH 54/74LS175
The M54/74HC175is ahigh speedCMOSQUADD-
TYPE FLIP-FLOP WITH CLEAR fabricated in sili-
con gate CMOS technology. It has the same high
speed performance of LSTTL combined with true
CMOS low power consumption.
These four flip-flops are controlled by a clock input
(CLOCK) and a clear input (CLEAR). The informa-
tion data applied to the Dinputs (1Dto4D) are trans-
fered to the outputs (1Q to 4Qand 1Qto 4Q) on the
positive-going edge of the clock pulse. The reset
function is accomplished when the clear input is
taken low and all Q outputs are kept low regardless
of other input conditions. All inputs are equipped
with protection circuits against static discharge and
transient excess voltage.
1/11
INPUT AND OUTPUT EQUIVALENT CIRCUIT
TRUTH TABLE
INPUTS OUTPUS
FUNCTION
CLEAR D CLOCK Q Q
L X X L H
H L L H
H H H L
H X Qn Qn NO CHANGE
X: Dont Care
LOGIC DIAGRAM
M54/M74HC175
2/11
PIN DESCRIPTION
PIN No SYMBOL NAME AND FUNCTION
1 CLEAR Master Reset Input
(Active LOW)
2, 7, 10, 15 1Q to 4 Q Flip Flop Outputs
3, 6, 11, 14 1Q to 4 Q Complementary Flip Flop
Outputs
4, 5, 12, 13 1D to 4D Data Inputs
9 CLOCK Clock Input (LOW to
HIGH, Edge-triggered)
8 GND Ground (0V)
16 V
CC
Positive Supply Voltage
IEC LOGIC SYMBOL
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit
V
CC
Supply Voltage -0.5 to +7 V
V
I
DC Input Voltage -0.5 to V
CC
+ 0.5 V
VO DC Output Voltage -0.5 to VCC + 0.5 V
I
IK
DC Input Diode Current 20 mA
I
OK
DC Output Diode Current 20 mA
IO DC Output Source Sink Current Per Output Pin 25 mA
I
CC
or I
GND
DC V
CC
or Ground Current 50 mA
P
D
Power Dissipation 500 (*) mW
Tstg Storage Temperature -65 to +150
o
C
T
L
Lead Temperature (10 sec) 300
o
C
AbsoluteMaximumRatingsare those values beyond whichdamage tothedevice may occur. Functional operation under these conditionisnot implied.
(*) 500 mW: 65
o
C derate to 300 mWby 10mW/
o
C: 65
o
C to85
o
C
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Value Unit
V
CC
Supply Voltage 2 to 6 V
VI Input Voltage 0 to VCC V
VO Output Voltage 0 to VCC V
T
op
Operating Temperature: M54HC Series
M74HC Series
-55 to +125
-40 to +85
o
C
o
C
t
r
, t
f
Input Rise and Fall Time V
CC
= 2 V 0 to 1000 ns
VCC = 4.5 V 0 to 500
V
CC
= 6 V 0 to 400
M54/M74HC175
3/11
DC SPECIFICATIONS
Symbol Parameter
Test Conditions Value
Unit
VCC
(V)
TA = 25
o
C
54HC and 74HC
-40 to 85
o
C
74HC
-55 to 125
o
C
54HC
Min. Typ. Max. Min. Max. Min. Max.
V
IH
High Level Input
Voltage
2.0 1.5 1.5 1.5
V
4.5 3.15 3.15 3.15
6.0 4.2 4.2 4.2
V
IL
Low Level Input
Voltage
2.0 0.5 0.5 0.5
V
4.5 1.35 1.35 1.35
6.0 1.8 1.8 1.8
VOH High Level
Output Voltage
2.0
VI =
V
IH
or
V
IL
I
O
=-20 A
1.9 2.0 1.9 1.9
V
4.5 4.4 4.5 4.4 4.4
6.0 5.9 6.0 5.9 5.9
4.5 IO=-4.0 mA 4.18 4.31 4.13 4.10
6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60
V
OL
Low Level Output
Voltage
2.0
V
I
=
V
IH
or
VIL
I
O
= 20 A
0.0 0.1 0.1 0.1
V
4.5 0.0 0.1 0.1 0.1
6.0 0.0 0.1 0.1 0.1
4.5 I
O
= 4.0 mA 0.17 0.26 0.33 0.40
6.0 IO= 5.2 mA 0.18 0.26 0.33 0.40
II Input Leakage
Current
6.0
VI = VCC or GND 0.1 1 1 A
I
CC
Quiescent Supply
Current
6.0 V
I
= V
CC
or GND 4 40 80 A
M54/M74HC175
4/11
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Symbol Parameter
Test Conditions Value
Unit
VCC
(V)
TA = 25
o
C
54HC and 74HC
-40 to 85
o
C
74HC
-55 to 125
o
C
54HC
Min. Typ. Max. Min. Max. Min. Max.
t
TLH
tTHL
Output Transition
Time
2.0 30 75 95 110
ns
4.5 8 15 19 22
6.0 7 13 16 19
tPLH
tPHL
Propagation
Delay Time
(CLOCK - Q, Q)
2.0 60 150 190 225
ns
4.5 19 30 38 45
6.0 16 26 32 38
tPLH
t
PHL
Propagation
Delay Time
(CLEAR - Q, Q)
2.0 50 125 155 190
ns
4.5 16 25 31 38
6.0 14 21 26 32
f
MAX
Maximum Clock
Frequency
2.0 6.2 13 5 4.2
MHz
4.5 31 52 25 21
6.0 37 61 30 25
tW(H)
tW(L)
Minimum Pulse
Width
(CLOCK)
2.0 28 75 95 110
ns
4.5 7 15 19 22
6.0 6 13 16 19
tW(L) Minimum Pulse
Width
(CLEAR)
2.0 28 75 95 110
ns
4.5 7 15 19 22
6.0 6 13 16 19
t
s
Minimum Set-up
Time
2.0 28 75 95 110
ns
4.5 7 15 19 22
6.0 6 13 16 19
t
h
Minimum Hold
Time
2.0 0 0 0
ns
4.5 0 0 0
6.0 0 0 0
tREM Minimum
Removal Time
(CLEAR)
2.0 5 5 5
ns
4.5 5 5 5
6.0 5 5 5
CIN Input Capacitance 5 10 10 10 pF
CPD (*) Power Dissipation
Capacitance
47
pF
(*) CPD isdefined as the value of the ICs internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the followingequation. ICC(opr) = CPD VCC fIN + ICC/4 (per FlipFlop)
M54/M74HC175
5/11
SWITCHING CHARACTERISTICS TEST WAVEFORM
TEST CIRCUIT I
CC
(Opr.)
M54/M74HC175
6/11
Plastic DIP16 (0.25) MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
a1 0.51 0.020
B 0.77 1.65 0.030 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 17.78 0.700
F 7.1 0.280
I 5.1 0.201
L 3.3 0.130
Z 1.27 0.050
P001C
M54/M74HC175
7/11
Ceramic DIP16/1 MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 20 0.787
B 7 0.276
D 3.3 0.130
E 0.38 0.015
e3 17.78 0.700
F 2.29 2.79 0.090 0.110
G 0.4 0.55 0.016 0.022
H 1.17 1.52 0.046 0.060
L 0.22 0.31 0.009 0.012
M 0.51 1.27 0.020 0.050
N 10.3 0.406
P 7.8 8.05 0.307 0.317
Q 5.08 0.200
P053D
M54/M74HC175
8/11
SO16 (Narrow) MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.004 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45 (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8 (max.)
P013H
M54/M74HC175
9/11
PLCC20 MECHANICAL DATA
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 9.78 10.03 0.385 0.395
B 8.89 9.04 0.350 0.356
D 4.2 4.57 0.165 0.180
d1 2.54 0.100
d2 0.56 0.022
E 7.37 8.38 0.290 0.330
e 1.27 0.050
e3 5.08 0.200
F 0.38 0.015
G 0.101 0.004
M 1.27 0.050
M1 1.14 0.045
P027A
M54/M74HC175
10/11
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specificationsmentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronicsproductsare not authorized for use ascritical componentsin life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
M54/M74HC175
11/11