Scribd Logo
Upload

Welcome to Scribd!

  • 178 views

    Installation Techniques - Link-Seal Modular Seals: Connect

    Uploaded by

    aleonr10
    LS-325 thru. LS-650 Using a hand socket or offset wrench ONLY, start at 12 O' Clock. Do not tighten any bolt more than 4 turns at a time. Make 2 or 3 more passes at 4 turns per bolt MAXIMUM, tightening all bolts clockwise until all sealing elements "bulge" around all pressure plates.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Installation Techniques - Link-Seal Modular Seals: Connect

    Uploaded by

    aleonr10
    178 views1 page
    LS-325 thru. LS-650 Using a hand socket or offset wrench ONLY, start at 12 O' Clock. Do not tighten any bolt more than 4 turns at a time. Make 2 or 3 more passes at 4 turns per bolt MAXIMUM, tightening all bolts clockwise until all sealing elements "bulge" around all pressure plates.

    Original Title

    Instalacion Link Seal

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    LS-325 thru. LS-650 Using a hand socket or offset wrench ONLY, start at 12 O' Clock. Do not tighten any bolt more than 4 turns at a time. Make 2 or 3 more passes at 4 turns per bolt MAXIMUM, tightening all bolts clockwise until all sealing elements "bulge" around all pressure plates.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    178 views1 page

    Installation Techniques - Link-Seal Modular Seals: Connect

    Uploaded by

    aleonr10
    LS-325 thru. LS-650 Using a hand socket or offset wrench ONLY, start at 12 O' Clock. Do not tighten any bolt more than 4 turns at a time. Make 2 or 3 more passes at 4 turns per bolt MAXIMUM, tightening all bolts clockwise until all sealing elements "bulge" around all pressure plates.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Installation Techniques - Link-Seal Modular Seals

    Online Installation Video


    Visit www.linkseal.com

    Connect
    1. Center the pipe, cable or
    conduit in wall opening or
    casing. Make sure the pipe
    will be adequately supported on both ends. LinkSeal modular seals are
    not intended to support the
    weight of the pipe.

    2. Loosen rear pressure


    plate with nut just enough
    so links move freely. Connect both ends of belt
    around the pipe.

    3. Check to be sure all bolt


    heads are facing the installer. Extra slack or sag is
    normal. Do not remove
    links if extra slack exists.
    Note: On smaller diameter
    pipe, links may need to be
    stretched.

    Bulge

    Installation Complete
    5a. LS-325 thru. LS-650
    Using a hand socket or offset wrench ONLY, start at
    12 O Clock. Do not tighten
    any bolt more than 4 turns
    at a time. Continue in a
    clockwise manner until
    links have been uniformly
    compressed. (Approx. 2 or
    3 rotations)

    6. Make 2 or 3 more
    passes at 4 turns per bolt
    MAXIMUM, tightening all
    bolts clockwise until all
    sealing elements bulge
    around all pressure plates.
    On type 316 stainless steel
    bolts, hand tighten ONLY
    without power tool.

    7. If the seal doesnt appear to be correct using


    the instructions provided,
    Call PSI at 800-423-2410.

    4. Slide belt assembly into


    annular space. For larger
    size belts, start inserting
    Link-Seal modular seal assembly at the 6 OClock
    position and work both
    sides up toward the 12 OClock position in the annular space.

    5. LS-200 thru. LS-315


    Using a hand socket allen
    head or off-set wrench
    ONLY, start at 12 O Clock.
    Do not tighten any bolt
    more than 4 turns at a
    time. Continue in a clockwise manner until links
    have been uniformly compressed. (Approx. 2 or 3
    rotations)

    Link-Seal Model

    Tool Size/
    Type Req.

    LS-200, LS-275

    4mm, Allen

    LS-300, LS-315

    6mm, Allen

    LS-325, LS-340, LS-360

    13mm, Hex

    LS-400, LS-410, LS-425, LS-475

    17mm, Hex

    LS-500, LS-525, LS-575

    19mm, Hex

    LS-600

    30mm, Hex

    LS-650

    19mm, Hex

    Installation Notes: The Link-Seal modular seal bolt heads are usually recessed below
    the wall opening or the edge of casing pipe and therefore a socket or offset wrench must
    be used. Hand Tools: Review provided chart above. (Tools not provided.) Tools can be
    purchased from hardware store, auto parts store, or home improvement store.

    Always Wear Safety Equipment When Using Link-Seal Modular Seals!


    Link-Seal Modular Seal - Dos

    1. Make sure pipe is centered.


    2. Install the belt with the
    pressure plates evenly
    spaced.
    3. Install the exact number

    of links indicated in sizing


    charts.
    4. Check to make sure pipe
    is supported properly during backfill operations.
    Note: Link-Seal modular
    seals are not intended to
    support the weight of the
    pipe.
    5. Make sure seal assembly and pipe surfaces are
    free from dirt.
    6. For tight fits, use nonpolluting liquid detergent to
    assist
    installation.

    If the seal doesnt appear to be correct using the


    techniques provided, Call PSI at 713-747-6948
    or 800-423-2410.

    Link-Seal Modular Seal - Donts

    Dont
    1. Dont Install the belt with
    the pressure plates aimed
    in irregular directions.
    (Staggered)

    2. Dont Install Link-Seal


    modular seals where weldbeads or other irregular
    surfaces exist without consideration of the sealing requirements.
    3. Dont torque each bolt
    completely before moving
    on to the next.
    4. Dont use high speed
    power tools (450 rpm or
    more)
    5. Do not use power tools
    on Link-Seal modular seal
    316 stainless steel bolts.
    6. Dont use grease installing Link-Seal modular
    seals.

    You might also like