Reference Guide OTN

OTN (G.
709) Reference Guide

Your insight into the optical transport network
Edition
4
th
About EXFO
About the Author
EXFO is among the leading providers of next-generation test and service assurance solutions for wireless and wireline network operators
and equipment manufacturers in the global telecommunications industry. The company offers innovative solutions for the development,
installation, management and maintenance of converged, IP fixed and mobile networks from the core to the edge. Key technologies
supported include 3G, 4G/LTE, IMS, Ethernet, OTN, FTTx, and various optical technologies (accounting for an estimated 35% of the
portable fiber-optic test market). EXFO has a staff of approxim ately 1600 people in 25 countries, supporting more than 2000 telecom
customers worldwide.
Mai Abou-Shaban, Product Specialist, Transport and Datacom Business Unit, brings to EXFO her extensive experience in optical
transport networks on addition to working with major telecom accounts in Americas, EMEA and Asia. She holds a Bachelor degree in
Electrical Engineering from Concordia University, Montreal, QC. Mai has eleven years of experience working for public and privately held
companies in the areas of systems engineering, product marketing as well as in sales support.
OTN (G.709) Reference Guide EXFO 1
Table of Contents
1. Introduction ..............................................................................3
2. Optical Transport Network (OTN) Layers ..................5
3. G.709 Interfaces and Rates .............................................9
4. OTU Frame Structure and Overhead .......................... 11
4.1 Framing ......................................................................................11
4.2 Overhead....................................................................................13
4.2.1 Optical Channel Transport Unit (OTU) Overhead .....13
4.2.2 Optical Channel Data Unit (ODU) Overhead ..............16
4.2.3 Optical Channel Payload Unit (OPU) Overhead ........24
4.3 OTU Forward Error Correction (FEC) .....................................28
5. OTN Multiplexing .................................................................. 31
5.1 ODUk Multiplexing ............................................................... 31
5.2 ODU0 ...................................................................................... 32
5.3 ODUFlex ................................................................................. 35

6. Overclocked Optical Transport Network ................. 37
6.1 OTU2e10GBASE-R Signal Mapping into OPU2e............ 38
6.2 OTU1e10GBASE-R Signal Mapping into OPU1e........... 39
6.3 GFP-F Mapping of 10GBASE-R into OPU2 ......................... 39
6.4 ODU2 Signal Mapping into ODU3e ..................................... 39
7. Testing Optical Transport Network Elements ...... 40
7.1 Interface Specications Test ............................................ 41
7.2 Response Test .................................................................... 42
7.3 Conformance and Interoperability Test........................... 43
7.4 Client Signal Mapping Test ................................................. 43
7.5 Appropriate FEC Behavior Test .......................................... 44
7.6 ODU1 to ODU2 Multiplexing................................................ 45
7.7 ODU0 to OTU2 Multiplexing ................................................ 45
7.8 OTN as a Service .................................................................. 46
7.8.1 Todays OTN Structure...................................................48
8. Conclusion .............................................................................. 50
9. Acronyms ................................................................................ 52
2 OTN (G.709) Reference Guide EXFO
1
Introduction
1. Introduction
In todays telecom/datacom environment, network operators are forced to integrate their networks in order to reduce operational expenses
(OPEX) and eliminate the additional capital expenditures (CAPEX) generated by multiple parallel networks. Every network operator is therefore
attempting to provide the greatest number of services on the leanest possible infrastructure to drive faster returns on investments. For instance,
traditional telecom carriers and service providers are now considering deploying new technologies to help meet new market demands and
challenges. Examples of such technological changes include implementing broadband accessboth wired (e.g., xDSL, FTTx) and wireless
(IEEE 802.11); as well as migrating from circuit-switched voice services to voice-over-IP (VoIP) and from ATM- and FDDI-based solutions to gigabit
Ethernet. In addition, there is the added pressure of growing demand for high-capacity, xed-bandwidth services and the challenge of fulfilling
all their requirements.
In response to such changes, the ITU-T developed a set of standards to meet these emerging needs. ITU-T recommendation G.709, Interface for
the optical transport network (OTN), is among the latest of these standards, and its aim is to address the transmission requirements of todays
wide range of services; namely, it was developed to assist in network evolution to higher bandwidth and improve network performance. Many of
the notions in ITU-T G.709 are similar to those in SONET/SDH; e.g., layered structure, in-service performance monitoring, protection and other
management functions. However, some key elements have been added to continue the cycle of improved performance and reduced cost. Among
these key elements, the ITU-T G.709 provides a standardized way to manage the optical channels in the optical domain without the need to convert
the optical signals to electrical signals, to apply a forward error correction (FEC) algorithm to improve transmission performance, to enable longer
spans, and to scale at 100G rates.
Currently, the majority of OTN applications are running on dense wavelength-division multiplexing (DWDM) transport networks. However, products
that support OTN standards to various degrees are already available and even more OTN-based product lines and feature sets are expected to
hit the market in the very near future.
2
Optical Transport Network (OTN)
Layers
Figure 2.1 IaDI vs. IrDI Interfaces
User
3R 3R 3R
Intra-Domain
IaDI
User
3R
Intra-Domain
IaDI
Intra-Domain
IaDI
Intra-Domain
IaDI
Operator A Operator B
3R 3R
Inter-Domain
IrDI
Inter-Domain
IrDI
Inter-Domain
IrDI
2. Optical Transport Network (OTN) Layers
The optical transport hierarchy (OTH) is a new transport technology for optical transport networks (OTNs) developed by the ITU. It is based on
the network architecture dened in various recommendations (e.g., G.872 on architecture; G.709 on frames and formats and G.798 on functions
and processes). OTH combines electrical and optical multiplexing under a common framework. The electrical domain is structured in a hierarchical
order, just like SONET/SDH, and the optical domain is based on DWDM multiplexing technology but with standardized interfaces and methods to
manage the network. ITU-T recommendation G.872, Architecture for the Optical Transport Network (OTN), denes two classes of OTN interfaces
(see Figure 2.1- IaDI vs. IrDI interfaces).

OTN inter-domain interface (IrDI): This interface connects the networks of two operators, or the subnetworks of one or multiple vendors in
the same operator domain. The IrDI interface is dened with 3R (reshape, regenerate and retime) processing at each end.

OTN intra-domain interface (IaDI): This interface connects networks within one operator and vendor domain.
Client signal
OPU
ODU
OTU
OCh
OMS
OTS OTS
OTU
OCh
OMS
OTS
OTU
OCh
OMS
OTS OTS
T T A A 3R 3R
T = Client access point
A = Optical amplifier
3R = Regeneration, reshape, retime
The ITU G.872 recommendation also denes the optical network architecture based on the optical channel (OCh) carried over a specic
wavelength. Different from that of legacy DWDM systems, the structure of this signal is standardized. The OTN architecture is composed of three
layers, shown in Figure 2.2 - OTN Layer Termination Points, and constructed using the OCh with additional overheads.

Optical channel (OCh) represents an end-to-end optical network connection with the encapsulated client signal in the G.709 frame structure.

Optical multiplex section (OMS) refers to sections between optical multiplexers and demultiplexers.

Optical transmission section (OTS) refers to sections between any network elements in the OTN, including ampliers.
The termination of the OTS, OMS and OCh layers is performed at the optical level of the OTN. The OCh payload consists of an electrical
substructure, where the optical channel transport unit (OTU) is the highest multiplexing level. This layer is the digital layeralso known as the digital
wrapperwhich offers specic overhead to manage the OTNs digital functions. The OTU also introduces a new dimension to optical networking
by adding forward error correction (FEC) to the network elements, allowing operators to limit the number of required regenerators used in the
network and in turn reduce cost.
Figure 2.2 OTN Layer Termination Points
The transport of a client signal in the OTN (shown
in Figure 2.3 Basic OTN Transport Structure)
starts with the client signal (SONET/SDH,
Ethernet, FC, ATM, GFP, etc.) being adapted at
the optical channel payload unit (OPU) layer by
adjusting the client signal rate to the OPU rate.
The OPU overhead itself contains information to
support the adaptation process of the client signal.
Once adapted, the OPU is mapped into the optical
channel data unit (ODU) with the necessary ODU
overhead to ensure end-to-end supervision and
tandem connection monitoring. Finally, the ODU is
mapped into an OTU, which provides framing, as
well as section monitoring and FEC.
Each OTUk (k = 1, 2, 3, 4) is transported using an optical channel (OCh) assigned to a specic wavelength of the ITU grid. Several channels
can be mapped into the OMS layer and then transported via the OTS layer. The OCh, OMS and OTS layers each have their own overhead for
management purposes at the optical level. The overhead of these optical layers is transported outside of the ITU grid in an out-of-band common
optical supervisory channel (OSC). In addition, the OSC provides maintenance signals and management data at the different OTN layers.
OCh
Client signal
Client signal
OPU
OPU
OH
ODU
OH
ODU
OMS
OTS
OTU
OH
OCh OCh
Client
OPU
ODU
OTU
OMS
OTS
OCh
FEC
OCh OH
OMS OH
OTS OH
OSC
OCh
Encapsulation Decapsulation
SONET, SDH, Null, PRBS, Ethernet and FC
Figure 2.3 Basic OTN Transport Structure
3
G.709 interfaces
and Rates
OTN Interface Line Rate Corresponding Service
ODU0 (virtual) 1.244 Gbit/s
Gig-E
OC-3/STM-1
OC-12/STM-4
OTU1 2.666 Gbit/s OC-48/STM-16
OTU2 10.709 Gbit/s
OC-192/STM-64
10 GigE LAN (using GFP-F)
OTU1e 11.0491 Gbit/s (without stufng bits) 10 GigE LAN (direct mapping over OTN)
OTU2e 11.0957 Gbit/s (with stufng bits) 10 GigE LAN (direct mapping over OTN)
OTU1f 11.27 Gbit/s (without stufng bits) 10G Fibre Channel
OTU2f 11.3 Gbit/s (with stufng bits) 10G Fibre Channel
OTU3 43.018 Gbit/s
OC-768/STM-256
40GE
OTU3e1 44.57 Gbit/s 4X ODU2e (uses 2.5G TS; total of 16)
OTU3e2 44.58 Gbit/s 4X ODU2e (uses 1.25G TS; total of 32)
OTU4 111.81 Gbit/s 100GE
3. G.709 Interfaces and Rates
The ITU-T G.709 recommendation denes standard interfaces and rates based on the existing SONET/SDH rates, along with packet-based
services including Ethernet and Fibre Channel. When taking into consideration the additional G.709 overhead and FEC information, the resulting
interfaces operate at line rates roughly 7% higher than the corresponding SONET/SDH rates. Table 3.1 G.709 Dened Interfaces lists the G.709
line rates and their corresponding SONET/SDH interfaces along with packet based services including Ethernet and Fiber Channel.
Table 3.1 G.709 Dened interface lists the G.709 lie rates and their corresponding mapped client services.
4
OTU Frame Structure
and Overhead
4. OTU Frame Structure and Overhead
Figure 4.1 - OTU Frame Structure illustrates the three parts that constitute the optical channel transport unit (OTU) frame:

Framing (frame alignment signal and multiframe alignment signal)

OTU, ODU, OPU overhead

OTU forward error correction
4.1. Framing
When transmitting serial blocks of data in an optical transport system, it is essential for the receiving equipment to identify the block boundaries.
The ability to identify the starting point in the OTN is accomplished through the use of framing bytes, which are transmitted in every frame. The OTU
framing structure is divided into two portions: frame alignment signal (FAS) and multiframe alignment signal (MFAS), shown in Figure 4.2 G.709
Frame Alignment.
SAPI
DAPI
Operator-
Specific
0
.
.
.
15
16
.
.
31
32
.
.
.
.
63
SAPI
DAPI
Operator-
Specific
0
.
.
.
15
16
.
.
31
32
.
.
.
.
63
0
1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
255
TTI
8 9 10
TTI BIP-8
1 2 3 4 5 6 7 8
BEI/BIAE RES
B
D
I
I
A
E
1 2 3 4 5 6 7 8
BEI STAT
B
D
I
1 2 3 4 5 6 7 8
BEI/BIAE STAT
B
D
I
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1 2 3 4 5 6 7 8 9 10 11 12 13 14
FAS
FAS OH OTU OH
GCCO
M
F
A
S
SM RES
1
2
3
2
3
4
4
ODU OH
O
P
U

O
H
OTU FEC
(4 x 256 bytes)
OPU Payload
(Client Signal)
1 2 3
TTI BIP-8
Byte 10
1.......................................................................................14.15. 16. 17...............................................................................................................3824. 3825............................................4080
OTU
Frame
RES TCM6 TCM5 TCM4
TCM3 TCM2 TCM1 PM EXP
GCC1
15 16
1
2
3
4 PSI
M
a
p
p
i
n
g
PT
M
a
p
p
i
n
g
GCC2 APS/PCC RES
TCM
ACT
PM&
TCM
Operator
Identifier
FIF
FTFL
PM and TCMi (i= 1 to 6)
PM
TCMi
Byte 3
Operator-
Specific
Operator
Identifier
FIF
Operator-
Specific
0........1................................9. 10.........................................................127
128...129........................137. 138.....................................................255
Forward
Backward
FIF = Fault Identification Field
FTFL
Figure 4.1 OTU Frame Structure

Frame alignment signal (FAS) uses the rst six bytes in row
1, columns 1 to 6. As in SONET/SDH, G.709 uses FAS to provide
framing for the entire signal and to identify out-of-frame (OOF) and
loss-of-frame (LOF) conditions

Multiframe alignment signal (MFAS) G.709 supports
multiframing structure, in which some of the OTUk and ODUk
overhead signals could span multiple OTU frames. Examples are the
trail trace identier (TTI) and tandem connection monitoring activation
(TCM-ACT) overhead signals. A single MFAS byte is used to extend
command and management functions over several frames. The MFAS
byte is dened in row 1, column 7 of the G.709 frame and incremented
for each OTUk/ODUk frame, providing a 256 multiframe structure.
4.2. Overhead
4.2.1. Optical Channel Transport Unit (OTU) Overhead
The OTU overhead is comprised of the SM, GCC0 and RES bytes, shown in Figure 4.3 OTU Overhead and SM Structure.

Section monitoring (SM) bytes are used for the trail trace identier (TTI), parity (BIP-8) as well as the backward error indicator (BEI), backward
incoming alignment error (BIAE), backward defect indicator (BDI), and incoming alignment error (IAE).

SM trail trace identier (TTI) is a one-byte overhead eld dened to support 64-byte trace signals. TTI is used to identify a signal from the
source to the destination within the network. The TTI contains the so-called access point identiers (API) eld, which is used to specify the
source access point identier (SAPI) and destination access point identier (DAPI). The APIs contain information regarding the country
of origin, network operator and administrative details.
Framing
FAS
OTU OH
Byte
Byte
1
2
3
4
1 7 8 14151617 3824 3825 4080
Payload
OTU
FEC
ODU (TCMi)
OH
1
1
2 3 4 5 6 7
MFAS
O
P
U

O
H
Figure 4.2 G.709 Frame Alignment

SM error bit-interleaved parity-8 (BIP-8) is a one-byte error detection
code signal. The OTUk BIP-8 is computed over the OPUk area of a
specic frame and inserted in the OTUk BIP-8 overhead two frames
later.

SM backward defect indication (BDI) is a single-bit signal dened to
convey the signal fail status detected in the upstream direction.

SM backward error indication and backward incoming alignment
error (BEI/BIAE) is a four-bit signal used to convey in the upstream
direction the number of interleaved-bit blocks detected in error by
the section monitoring BIP-8 code. It is also used to convey in the
upstream direction an incoming alignment error (IAE) condition that
is detected in the section monitoring IAE overhead.

General communications channel (GCC0) eld, which resembles
the data communications channel (DCC) in SONET/SDH, is currently
undened, but it will likely be used for functions such as network
management or control plane signaling for a protocol like generic
multiprotocol label switching (G-MPLS).

Reserved (RES) elds, found throughout the overhead, are set aside
for future use.
Framing
SM RES
OTU OH
Byte
Byte
1
2
3
4
8
1 4 5 6 7 8
9 10
Payload
OTU
FEC
8
1
9 10 11 12 13 14
GCC0
TTI
SAPI
BEI/
BIAE
BDI IAE RES
DAPI
Operator
Specific
BIP-8
0
15
16
31
32
63
ODU (TCMi)
OH
1 7 8 14151617 3824 3825 4080
O
P
U
1

O
H
Figure 4.3 OTU Overhead and SM Structure
Table 4.1 Summary of OTU Overhead Bytes
Field Denition
Section monitoring
(SM)
SM consists of the following bytes; TTI, BIP-8, BEI, BIAE, BDI and IAE
Trail trace identier (TTI) The 64-byte multiframe TTI signal is similar to the J0 byte in SONET/SDH.
Bit-interleaved parity (BIP-8)
The BIP-8 value covers the OPU and client payload of the G.709 frame and its value is
inserted in the BIP-8 eld of the second frame following calculation.
Backward defect indication (BDI)
When an AIS is sent in the downstream direction as a response to a signal fail indication
(such as in the FTFL), the upstream direction response to continuity, connectivity and
maintenance signals is a backward defect indication (BDI) signal. BDI is raised as an alarm
when it has been received for ve consecutive frames.
Backward error indication (BEI)
The detection of a frame slip, which can occur at the OTU, generates an and backward
incoming alignment error (IAE) in the downstream direction. The three-bit value alignment
error (BIAE)
STAT
These three bits indicate the presence of maintenance signals
(AIS, OCI, TCMi, IAE).
General
communication
channel 0 (GCC0)
A clear channel used for transmission of information between OTU termination points.
RES Reserved bytes that are currently undened in the standard.
Framing OTU OH
Byte
Byte
1
2
3
4
Payload
OTU
FEC
ODU (TCMi)
OH
1
1
2 3 4 5 6 7 8 9 10 11 12 13 14
RES
TCM6 TCM5 TCM4
TCM
ACK
FTFL
2
TCM3 TCM2 TCM1 PM EXP
3
GCC1 GCC2 APS/PCC RES 4
TTI
BEI/BIAE BDI RES
BIP-8
0
15
16
31
32
63
Applies to PM
and TCM1-6
SAPI
DAPI
Operator-
Specific
O
P
U

O
H
1 4 6 5 8
7 8 14151617 3824 3825 4080
PM &
TCM
4.2.2.Optical Channel Data Unit Overhead
The optical channel data unit (ODU) overhead,
shown in Figure 4.4 ODU Overhead and PM/
TCMi Structure, supports two classes of ODUk
maintenance signals, reported using path monitoring
overhead (PMOH) status (STAT) bits and tandem
connection monitoring (TCM) STAT bits. Through
either PMOH or TCM STAT bits, the following ODU
conditions can be reported: alarm indication signal
(ODUk-AIS), open connection indication (ODU-OCI),
locked (ODUk-LCK), and generic AIS. In addition,
the ODUk overhead supports automatic protection
switching (APS) functionality. The ODUk overhead
is broken into the following elds: RES, PM, TCMi,
TCM ACT, FTFL, EXP, GCC1/GCC2 and APS/PCC.
Figure 4.4 ODU Overhead and PM/TCMi Structure

Reserved (RES) bytes are undened and are set aside for future applications.

Path monitoring (PM) enables the monitoring of particular sections within the network as well as fault location in the network. The PM bytes
are congured in row 3, columns 10 to 12, and contain subelds similar to the ones in SM including: TTI, BIP-8, BEI, BDI and Status (STAT)
subelds.

PM trail trace identier (TTI) is a one-byte overhead eld similar to the J0 byte in SONET/SDH. It is used to identify the signal from the source
to the destination within the network. The TTI contains the so-called access point identiers (API) eld, which is used to specify the source
access point identier (SAPI) and destination access point identier (DAPI). The APIs contain information regarding the country of origin,
network operator and administrative details.

PM bit-interleaved parity (BIP-8) is a one-byte eld, which is used for error detection. The BIP-8 byte provides a bit-interleaved parity eight-
bit code computed over the whole OPU and inserted into the BIP-8 SM two frames later.

PM backward defect indication (BDI) is a single bit, which conveys information regarding signal failure in the upstream direction.

PM backward error indication (BEI) and backward incoming alignment error (BIAE) signals carry information on interleaved-bit blocks
detected in error in the upstream direction. These elds are also used to convey incoming alignment errors (IAE) in the upstream direction.

PM status (STAT) is a three-bit eld used to indicate the presence of maintenance signals.

Tandem connection monitoring (TCMi) elds, which are part of the ODU overhead, dene six ODU TCM sublayers. Each TCM sublayer
contains a TTI, BIP-8, BEI/BIAE, BDI and STAT subeld associated with a TCMi level (i = 1 to 6).

Tandem connection monitoring activation/deactivation (TCM ACT) is a one-byte eld located in row 2, column 4. TCM ACT is
currently undened in the standard.

Fault type and fault location (FTFL) is a one-byte eld located in row 2, column 14 of the ODU overhead and is used to transport a fault
type and fault location (FTFL) message, spread over a 256-byte multiframe for sending forward and backward path-level fault indications (shown
in Figure 4.5 FTFL Field Structure). The forward eld is allocated to bytes 0 through 127 of the FTFL message. The backward eld is allocated
to bytes 128 through 255 of the FTFL message.

Experimental (EXP) is a two-byte
eld located in row 3, columns 13 and
14 of the ODU overhead. The EXP
eld is not subject to standards and
is available for network operators to
support applications that may require
additional ODU overhead.

General communication channels
1 and 2 (GCC1/GCC2) are two elds
of two bytes each, and they support
general communication channels
between any two network elements;
similar to the GCC0 eld, except that they are available in the ODU overhead. GCC1 is located in row 4 and columns 1 and 2 and GCC2 is
located in row 4, columns 3 and 4 of the ODU overhead.

Automatic protection switching and protection communication channel (APS/PCC) is a four-byte signal dened in row 4, columns
5 to 8 of the ODU overhead. The APS/PCC eld supports up to eight levels of nested APS/PCC signals, which are associated with dedicated-
connection monitoring.
127 128 255
255 137 138 127 128 129 9 10 1 0
0
Fault
Indication
Field
Fault
Indication
Field
Operator
Identifier Field
Operator
Identifier Field
Operator
Specific Field
Operator
Specific Field
Forward Field Backward Field
Forward Backward
Figure 4.5 FTFL Field Structure
Field Denition
Path monitoring
PM consists of the following bytes; TTI, BIP-8, BEI, BIAE, BDI and IAE.
Trail trace identier (TTI) The 64-byte multiframe TTI signal is similar to the J0 byte in SONET/SDH.
Bit-interleaved parity (BIP-8)
The ODU PM contain a BIP-8 eld that covers the OPU and customer payload of the G.709
frame. The BIP-8 values are inserted in the BIP-8 eld of the frame following calculation.
Backward defect indication (BDI)
The AIS forwarded signal in the downstream direction is sent as a response to a signal
fail indication, such as in the FTFL or the incoming ODU-AIS. In the upstream direction,
the response to continuity, connectivity and maintenance signals is a backward defect
indication (BDI) signal indicated by a bit found in the PM and TCMi. BDI is raised as an alarm
when it has been received for ve consecutive frames.
Backward error indication (BEI) and
backward incoming alignment error
(BIAE)
The AIS forwarded signal in the downstream direction is usually sent as a response
to a signal fail indication, such as in the FTFL or the incoming ODU-AIS. In the upstream
direction the response to continuity, connectivity and maintenance signals is a BDI signal
indicated by a bit found in the PM and TCMi. BDI is raised as an alarm when it has been
received for ve consecutive frames.
STAT These three bits indicate the presence of maintenance signals (AIS, OCI, TCMi, IAE)
Table 4.2 Summary of ODU Overhead Bytes (continued on page 19)
Tandem connection monitoring (TCM)
Six TCM sublayers are dened in the ODU overhead. Each TCM sublayer contains TTI,
BIP-8. BEI/BIAE, BDI and STAT subelds.
Tandem connection monitoring activation/deactivation
(TCM ACT)
One-byte eld used for the activation and deactivation of the TCM elds. This eld is
currently undened in the standard.
Fault type and fault location (FTFL)
Reporting communication channel eld that is used to create a message for sending
forward and backward path-level fault indications.
Experimental (EXP)
This eld is not subject to standards and is available for network operator
applications.
General communication channel 1 and 2 (GCC1/GCC2)
Clear channels used for transmission of information at the ODU layer; similar to the
GCC0.
Automatic protection switching and protection communication
channel (APS/PPC)
This eld supports up to eight levels of nested APS/PCC signals, which are associated
to a dedicated-connection monitoring level.
RES Reserved bytes that are currently undened in the standard.
Table 4.2 Summary of ODU Overhead Bytes (continued)
TCM3 Domain and domain interconnect monitoring
TCM2 Lead operator QoS monitoring
TCM1 User QoS monitoring
Operator A Operator A
Operator B
User User

Tandem connection monitoring (TCM) has been implemented in SONET/SDH networks to enable carriers to monitor the quality of the
trafc across multiple networks. This has been achieved by breaking the path into a series of tandem paths, each owned and managed by
individual network operators. Errors and defects along the path can be traced to a particular tandem path for fast and easy troubleshooting.
Figure 4.6 Tandem Connection Monitoring shows an example of a small network operator (operator B) that is leasing network resources from
a larger network operator (operator A) rather than install its own networks. Operator A requires the ability to monitor the transmitted signal as it
passes through operator Bs network. Should a fault develop in the network, using tandem connection monitoring, operator A can quickly identify
whether the fault is located in operator Bs network, or further along the tandem path with another operator. In addition, different monitoring
functions can be assigned to different connections. For example in Figure 4.6 Tandem Connection Monitoring (TCM), TCM1 is assigned
to monitor the end-to-end quality of service (QoS), TCM2 is used by operator A to monitor their end-to-end QoS, and nally TCM3 is used for
various domains and domain-interconnect monitoring.
Figure 4.6 Tandem Connection Monitoring (TCM)
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
C1 - C2
B1 - B2
A1 - A2
A1 - A2
A1 B1 C1 C2 B2 B3 B4 A2
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
B1 - B2
B1 - B2
B3 - B4
A1 B1 C1 C2 B2 B3 B4 A2
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCMi
TCMi
TCMi
TCMi
TCM6
TCM5
TCM4
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
C1 - C2
A1 B1 C1 B2 C2 A2
TCM3
TCM OH field not in use
TCM OH field in use
TCM OH field in use
TCM OH field in use
In optical transport networks, each one of the six TCMi elds has the same structure as the PM eld, including the following subelds: TTI, BIP8,
BDI, BEI, status bits, indicating the presence of incoming alignment error (IAE) or a maintenance signal (STAT). Optical transport networks support
three TCM topologies, as shown in Figure 4.7 OTN Tandem Connection Monitoring (TCM) Topologies. Figure 4.7a shows tandem connections
C1-C2, B1-B2 and A1-A2 in nested conguration. Figure 4.7b shows tandem connections B1-B2 and B3-B4 in cascaded conguration. Finally,
Figure 4.7c shows tandem connections B1-B2 and C1-C2 in overlapping conguration.
Figure 4.7a TCM Topologies: Nested
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
C1 - C2
B1 - B2
A1 - A2
A1 - A2
A1 B1 C1 C2 B2 B3 B4 A2
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
B1 - B2
B1 - B2
B3 - B4
A1 B1 C1 C2 B2 B3 B4 A2
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCMi
TCMi
TCMi
TCMi
TCM6
TCM5
TCM4
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
C1 - C2
A1 B1 C1 B2 C2 A2
TCM3
TCM OH field in use
TCM OH field in use
TCM OH field in use
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
C1 - C2
B1 - B2
A1 - A2
A1 - A2
A1 B1 C1 C2 B2 B3 B4 A2
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
B1 - B2
B1 - B2
B3 - B4
A1 B1 C1 C2 B2 B3 B4 A2
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCMi
TCMi
TCMi
TCMi
TCM6
TCM5
TCM4
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
TCM6
TCM5
TCM4
TCM3
TCM2
TCM1
C1 - C2
A1 B1 C1 B2 C2 A2
TCM3
TCM OH field in use
TCM OH field in use
TCM OH field in use
Figure 4.7b TCM Topologies: Cascaded
Figure 4.7c TCM Topologies: Overlapping
Framing OTU OH
Byte
Byte
1
2
3
4
1 4080
Payload
OTU
FEC
ODU (TCMi)
OH
15
1
16
RES
17 24
2 RES
3 RES
4 PSI
JC
JC
JC
NJO PJO
PT
RES
PSI
0
1
2
255
7 8 14 15 16 17 3824 3825
O
P
U

O
H
C
S
F
4.2.3. Optical Channel Payload Unit (OPU) Overhead
The ITU-T G.709 standard currently denes mappings for
constant-bit-rate signals, both bit-synchronous and asynchronous.
This includes SONET/SDH, ATM, generic framing procedures
(GFP) and pseudo-random bit sequence (PRBS) patterns. As part
of the G.709 encapsulation process, the OPU overhead is added to
support the adaptation of the various client signals.
The OPU overhead is located in rows 1 to 4 of columns 15 and 16,
and it is terminated where the OPU is assembled and disassembled.
The OPU overhead consists of the following elds:

Payload structure identier (PSI) is a one-byte eld allocated
in the OPU overhead to transport a 256-byte payload structure
identier (PSI) signal. The PSI byte is located in row 4, column 15
of the OPU overhead.

Payload type (PT) is a one-byte eld dened in the PSI[0] byte
and contains the PT identier that reports the type of payload
being carried in the OPU payload to the receiving equipment.
Table 4.3 includes all possible payload type values currently
dened by the ITU-T G.709 standard.
Figure 4.8 OPU Overhead and PSI Field Structure
MSB
1 2 3 4
LSB
5 6 7 8
Hex Code
(Note 1)
Interpretation
0 0 0 0 0 0 0 1 01 Experimental mapping
0 0 0 0 0 0 1 0 02 Asynchronous CBR mapping
0 0 0 0 0 0 1 1 03 Bit-synchronous CBR mapping
0 0 0 0 0 1 0 0 04 ATM mapping
0 0 0 0 0 1 0 1 05 GFP mapping
0 0 0 0 0 1 1 0 06 Virtual Concatenated signal
0 0 0 0 0 1 1 1 07
PCS codeword transparent Ethernet mapping
- 1000BASE-X into OPU0
- 40GBASE-R into OPU3
- 100GBASE-R into OPU4
0000 1000 08 FC-1200 into OPU2e mapping
0000 1001 09 GFP mapping into Extended OPU2 payload
0000 1010 0A STM-1 mapping into OPU0
0000 1011 0B STM-4 mapping into OPU0
0 0 0 0 1 1 0 0 0C FC-100 mapping into OPU0
0 0 0 0 1 1 0 1 0D FC-200 mapping into OPU1
0 0 0 0 1 1 1 0 0E FC-400 mapping into OPUex
0 0 0 0 1 1 1 1 0F FC-800 mapping into OPUex
0 0 0 1 0 0 0 0 10 Bit stream with octet timing mapping
0 0 0 1 0 0 0 1 11 Bit stream without octet timing mapping
Table 4.3 Payload Type (PT) Dened Values
MSB
1 2 3 4
LSB
5 6 7 8
Hex Code
(Note 1)
Interpretation
0 0 0 1 0 0 1 0 12 IB SDR mapping into OPUex
0 0 0 1 0 0 1 1 13 IB DDR mapping into OPUex
0 0 0 1 0 1 0 0 14 IB QDR mapping into OPUex
0 0 0 1 0 1 0 1 15 SDI mapping into OPU0
0 0 0 1 0 1 1 0 16 (1.485/1.001) Gbit/s SDI mapping into OPU1
0 0 0 1 0 1 1 1 17 1.485 Gbit/s SDI mapping into OPU1
0 0 0 1 1 0 0 0 18 (2.970/1.001) Gbit/s SDI mapping into OPUex
0 0 0 1 1 0 0 1 19 2.970 Gbit/s SDI mapping into OPUex
0 0 0 1 1 0 1 0 1A SBCON/ESCON mapping into OPU0
0 0 0 1 1 0 1 1 1B DVD_ASI mapping into OPU0
0 0 1 0 0 0 0 0 20 ODU multiplex structure supporting ODTUjk only
0 0 1 0 0 0 0 1 21
ODU multiplex structure supporting ODTUk.ts
or ODTUk.ts and ODTUjk
0 1 0 1 0 1 0 1 55 Not available
0 1 1 0 0 1 1 0 66 Not available
1 0 0 0 x x x x 80-8F Reserved codes for proprietary use
1 1 1 1 1 1 0 1 FD NULL test signal mapping
1 1 1 1 1 1 1 0 FE PRBS test signal mapping
1 1 1 1 1 1 1 1 FF Not available
Table 4.3 Payload Type (PT) Dened Values

Multiplex structure identier (MSI) eld is used to encode the ODU multiplex structure in the OPU, and is located in the mapping-specic
area of the PSI signal. The MSI indicates the content of each tributary slot (TS) of an OPU.

Justication control (JC) overhead consists of justication control (JC), negative justication opportunity (NJO) and positive justication
opportunity (PJO) signals used in the ODU multiplexing process. The justication overhead bytes are used to make the justication decision in
the mapping/demapping process of the client signal to protect against an error in one of the three JC signals.
Field Denition
Payload structure identier (PSI) Dened to transport a 256-byte message aligned with MFAS.
Payload type (PT) Contains the payload type (PT) identier that reports the type of payload being carried in the
OPU payload to the receiving equipment eld, and it is currently undened in the standard.
Multiplex structure identier (MSI) Located in the mapping-specic area of the PSI signal, it is used to encode the ODU multiplex
structure in the OPU.
Justication control (JC) Justication control (JC), negative justication opportunity (NJO) and positive justication
opportunity (PJO) signals are used in the ODU multiplexing process to make the justication
decision in the mapping/demapping process of the client signal.
Table 4.4 Summary of OPU Overhead Bytes
4.3. OTU Forward Error Correction (FEC)
Forward error correction (FEC) is a major feature of OTN.
It uses a Reed-Solomon RS (255,239) algorithm code to produce
redundant information that gets concatenated with the transmitted
signal and used at the receive interface to help identify and correct
transmission errors. The FEC algorithm has been proven to be
effective in systems limited by optical signal-to-noise ratio (OSNR)
and dispersion. However, FEC is less effective against polarization
mode distortion.
Figure 4.9 BER vs. Eb/No compares a transport system
performance with and without FEC (G.709). Figure 4.9 shows
that the transport system with FEC capabilities is able to
transmit a signal at a certain bit error rate (BER) with less power
(approximately 6 dB) than one without FEC.
In the transmission process according to the RS (255, 239) FEC
algorithm, the OTU frame data is separated into four rows and
each row split into 16 subrows, as shown in Figure 4.10.
10
-15
10
-14
10
-13
10
-12
10
-11
10
-10
10
-9
10
-8
10
-7
10
-6
10
-5
10
-4
10
-3
10
-2
10
-1
2 3 4 5 6 7 8 9 10 11 12 13 14 15
Approximately 6 dB
G.709
Uncorrected
Figure 4.9 BER vs. Eb/No
Figure 4.11 Forward Error Correction (FEC) Mechanism
illustrates the process in which the FEC protocol is interleaving
one overhead byte and 238 data bytes to compute 16 parity
bytes to form 255-byte blocks; i.e., the RS (255,239) algorithm.
The key advantages of interleaving the information are to reduce
the encoding rate of each stream relative to the line transmission
rate and reduce the sensitivity to bursts of error. The interleaving,
combined with the inherent correction strength of the RS
(255,239) algorithm, enables the correction of transmission
bursts of up to 128 consecutive errored bytes.
The coding gain provided by the FEC is
used to increase the maximum span length
and/or the number of spans, resulting in an
extended reach through gain in power level.
It also helps increase the number of DWDM
channels in a DWDM system and allows the
usage of existing 2.5 Gbit/s links to transport
10 Gbit/s trafc. This is in addition to
increasing the number of transparent optical
network elements that can be crossed by an
optical path before amplication is needed.
Finally, OTN technology enables todays
point-to-point links to evolve into transparent
and more efcient meshed optical networks.
1...........................................239. 240...............255
1
1
2
3
4
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
OTU
Rows
OTU
Subrows
OH Payload Bytes FEC
Framing OTU OH 1
2
3
4
ODU OH
OPUPayload
1........................................................................................14. 15. 16. 17.......................................................................................3824. 3825..................4080
1.................................................................................14. 15. 16. 17..............................32........................................3824. 3825........................4080
1...........................................239. 240...............255
OTU
Frame
Row 1
Row 1
Subrow 1
(codeword)
Subrow 2
(codeword)
Subrow 3
(codeword)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
1
2
3
4
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
OTU
Rows
OTU
Subrows
OTUFEC
(4x 256bytes)
(Client Signal)
O
P
U

O
H
Figure 4.10 OTU Frame Rows
Figure 4.11 Forward Error Correction (FEC) Mechanism
5
ODU Multiplexing
5. OTN Multiplexing
5.1. ODUk Multiplexing
OTN (G.709) has also dened the multiplexing functions that allow four ODU1s to be multiplexed to an ODU2 and up to sixteen ODU1s, or four
ODU2s, to be multiplexed to an ODU3. It is also possible to mix ODU1s and ODU2s in an ODU3. The ODU multiplexing function is essential
for optimizing the network resources, including bandwidth usage. Typically, client signals consisting of 2.5 Gbit/s bit streams are transported
over a single DWDM wavelength. This might be an efcient service-delivery method if distances are short. However, if such services need to be
transported over long distances, it is quite expensive to use a dedicated wavelength.
The G.709 recommendation denes the optical payload unit
(OPU), which provides the overhead needed to support the
ODU multiplexing function. To multiplex four ODU1s into
ODU2, the OPU2 is divided into a number of tributary slots
(TS) interleaved within the OPU2, as shown in Figure 5.1
ODU1 Multiplexing to ODU2. Each OPU2 tributary slot
occupies 25% of the OPU2 payload area. In the multiplexing
process, the bytes of an ODU1 input are mapped into one
of the four OPU2 tributary slots. The multiplex structure
identier (MSI) is used to dene the type of multiplexing that
is implemented at the transmitter. The MSI is made of PSI
Bytes 2 to 17, but when multiplexing ODU1 in ODU2, only
Bytes 2 to 5 have a meaning; Bytes 6 to 17 are set to 0, as
they are intended for multiplexing applications with ODU3.
Framing
ODU1 OH
Client Signal
(e.g., OC-48/STM-16, ATM, GFP)
ODU2 OH
Framing
ODU OH
Client layer signal
(e.g., STM-16, ATM, GFP)
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU1 OH
Client Signal
ODU2 OH
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU1 OH
Client Signal
Framing OTU2 OH
OTU2
FEC
4x
ODU1
ODU2
OTU2
O
P
U
1

O
H
O
P
U
2

O
H
O
P
U
2

O
H
O
P
U
2
O
H
O
P
U
1
O
H
Figure 5.1 ODU1 Multiplexing to ODU2n
The information carried by the MSI is as follows:

ODU type carried by the OPU tributary slots (for example, ODU1 in an OPU2 tributary slot)

Tributary port to tributary slot assignment (for example, tributary port 1 mapped to OPU2 tributary slot 1)
In the case of ODU1 in ODU2, the tributary-port-to-tributary-slot assignment is xed, which means that tributary port 1 is assigned to tributary slot
1 and so on. Finally, an ODU2 overhead is added, after which the ODU2 is mapped into the OTU2 to complete the signal for transport.
The ODU multiplexing functionality of four OC-48/STM-16 signals in one OTU2 is both bit and timing-transparent. This ensures that the integrity
of the whole client signal is maintained and the input timing of a synchronous signal is transferred to the far end. ODU multiplexing is also
delay-transparent. When four OC-48/STM-16 signals are mapped into ODU1s and then multiplexed into an ODU2, their timing relationship is
preserved until they are demapped back to ODU1s at their destinations.
5.2. ODU0
In order to optimize the transport of gigabit Ethernet, a new
container was introduced by the G.709 standard; this container,
which has an optical channel payload unit (OPU) payload size of
1.238 Gbit/s, provides perfect mapping for gigabit Ethernet trafc.
While some multiplexing justication control mechanisms, like
generic mapping procedure (GMP), will be used, generic framing
procedure (GFP-T) is also used to transcode the Ethernet signal into
the payload of the ODU0.
Alignm
ODU0 OH
Client Layer Signal
ODU1 OH
ODU OH
Client layer signal
Alignm
ODU OH
Client Layer signal
ODU OH
Client layer signal
Alignm
ODU0 OH
Client Layer Signal
2x
ODU0
ODU1
Note - The ODU1 floats in 1/2 of the OPU1 Payload area. An ODU0 frame will cross multiple
ODU1 frame boundaries. A complete ODU0 frame (15 296 bytes) requires the bandwidth of one.
TribSlot in (15 296/7616 =) 23.0008 ODU1 frames. Ths is not illustrated.
Note - The OPU1 OH contains 1 column of justification control and opportunity overhead for
each of the 2 tribuary slots in a 2-frame multiframe format. This is not illustrated.
O
P
U
0

O
H
O
P
U
1

O
H
O
P
U
0
O
H
ODU1 OH
ODU1
with OPU1
Tributary
Slots
TS1, TS2
O
P
U
1

O
H
T
S
1
T
S
2
T
S
1
T
S
2
T
S
1
T
S
2
T
S
1
T
S
2
Figure 5.2 ODU0 Multiplexing to ODUkn
In order to inform the receive end on the number of payload bytes that are transported by the OPUk payload for each frame, GMP uses the OPU overhead
(OH) justication control bytes. The server frame (or multiframe) is divided into a certain number of GMP words where each word may contain data:

Words containing data are distributed evenly across server frame using sigma/delta distribution algorithm

Correct operation depends on the capacity of the mapper/de-mapper to distinguish the number of data words lled into each frame
The number of payload bytes transported is signaled over the justication-control JC1, JC2, JC3 bytes, using the Cm word; the change of
number of bytes is signaled with 2 bits designated as increment indicator (II) and decrement indicator (DI). GMP also provides a mechanism to
accommodate client signals with tighter jitter requirements (i.e., SONET/SDH client signals). It uses the justication-control JC4, JC5 and JC6
bytes to carry a 10-bit word (designated as:CnD).
The ODU0 container was introduced to deliver greater
efciency in the network. The following gure illustrates
how using an ODU0 container for Ethernet mapping results
in gained efciency. Multiple timeslots are allocated for
mapping; in the case of an OTU1 (2.5 Gbit/s), there are two
time slots allocatedeach running at 1.25 Gbit/sfor a total
bandwidth around 2.5 Gbit/s. Also, minimal bandwidth loss
is observed. Following the same analogy, up to 80 time slots
can be allocated in an OTU4 pipe.
Framing
ODU1 OH
Client Signal
ODU2 OH
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU1 OH
Client Signal
ODU2 OH
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU1 OH
Client Signal
Framing OTU2 OH
OTU2
FEC
4x
ODU1
ODU2
OTU2
O
P
U
1

O
H
O
P
U
2

O
H
O
P
U
2

O
H
O
P
U
2
O
H
O
P
U
1
O
H
Figure 5.3 ODU1 Multiplexing to ODU2n
2.5G Tributary Slots 1.25G Tributary Slots
OPU2 OPU3 OPU1 OPU2 OPU3 OPU4
ODU0 - - AMP (PT = 20) GMP (PT = 21) GMP (PT = 21) GMP (PT = 21)
ODU1 AMP (PT = 20) AMP (PT = 20) - AMP (PT = 21) AMP (PT = 21) GMP (PT = 21)
ODU2 - AMP (PT = 20) - - AMP (PT = 21) GMP (PT = 21)
ODU2e - - - - GMP (PT = 21) GMP (PT = 21)
ODU3 - - - - - GMP (PT = 21)
ODUex - - - GMP (PT = 21) GMP (PT = 21) GMP (PT = 21)
A multistage multiplexing will now be used
to bring the lower OTN rate to a higher rate,
where an ODU0 could be inserted directly
to an ODU4 100G rate.
1 GigE
Packet
1 GigE
Packet
1 GigE
Packet
OTU1
Transport
Pipe
TS 1
TS 2
OTU1
Transport
Pipe
Legacy Mapping
New Mapping
ODU0
ODU0
G
M
P
G
M
P
Figure 5.4 - GE Mapping Using the ODU0 Containers multiplexed into ODU1
Table 5.1 - Tributary OTN Mapping
ODUn OH
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODUx OH
Client Layer Signal
ODUn OH
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODU OH
Client layer signal
Framing
ODUx OH
Client Layer Signal
Framing OTUn OH
OTUn
FEC
ODUn
OTUn
O
P
U
n

O
H
O
P
U
n

O
H
O
P
U
x
O
H
O
P
U
x
O
H
5.3. ODUFLEX
Depending on the client signal data rates that need to be transported, having a exible container can be useful; and ODUex offers this exibility.
Similar to the VCAT technology used in SONET/SDH, ODUex provides an efcient and easy solution for mapping packet services and constant
bit rate (CBR) signal like ber channel. It uses 1.25G tributary time slots (ODTUGk) to create a variable container, where a client signal is mapped
and then transported over an ODUk signal, for the non-CBR signals ODUex use generic framing procedure (GFP-F) to map the signal. One of
the key advantages of ODUex is that the unused timeslot can be reused, and the bandwidth is adjustable.
Figure 5.5 ODUx Multiplexing to OTUn (where x=0 to n-1)
6
Overclocked Optical Transport Network
6. Overclocked Optical Transport Network
There is an increasing demand for deploying 10 Gbit/s Ethernet LAN/WAN and Fibre Channel services and terminating them across the optical
transport layer. Core IP routers are a prime example of this application where multiple 10 Gbit/s interfaces can be terminated in a particular location
and transported long distances across the DWDM core optical network. In addition, the integrated packet optical transport networks (P-OTN),
built upon the ITU-Ts optical transport network (OTN) standards, are efciently provisioning, transporting and managing legacy TDM services and
data-packet services over the same infrastructure.
Overclocked OTN is a technology that enables the
transportation of 10 GbE LAN signals transparently over
OTN networks as per ITU-T series G supplement 43 (see
Figure 6.1). Overclocked OTN compensates for the rate
mismatch between 10 GbE LAN and the OPU2 payload
by raising the overall OTU2 data rate from the standard
10.709 Gbit/s to t the 10 GbE LAN client signal. Obviously
with this modication of the standard OTN line rate,
interoperability issues will arise and the option for aggregating
OTU2 signals into OTU3 is lost; however, ODU3e allows for
multiplexing. On the positive side, overclocked OTN offers real
bit transparency of 10 GbE LAN signalsa necessity for the
mass deployment of 10 G services.
Overclocked OTN supports OTU1e, OTU2e, OTU3e1 and OTU3e2 optical line rates for mapping 10-GigE LAN signals. Furthermore, OTU1f and
OTU2f line rates are used for mapping Fibre Channel signals.
10 Gig-E LAN Service
11.0491G or 11.0957G OTN signal
10 Gig-E router
Figure 6.1 End-to-End IP Connectivity over OTN Networks
G.709 Interface OTN Line Rate Corresponding Client Rate
OTU-1e 11.0491 Gbit/s (without stufng bits) 10 Gig-E LAN (direct mapping over OTN)
OTU-2e 11.0957 Gbit/s (with stufng bits) 10 Gig-E LAN (direct mapping over OTN)
OTU-1f 11.27 Gbit/s 10G Fibre Channel
OTU-2f 11.3 Gbit/s 10G Fibre Channel
OTU-3e1 44.57 Gbit/s 4 x ODU2e (uses 2.5G TS; total of 16)
OTU-3e2 44.58 Gbit/s 4 x ODU2e (uses 1.25G (ODU0) TS; total of 32)
The transparent transportation of 10 GigE LAN signals means that the full 10 Gigabit Ethernet data rate (10.3125 Gbit/s) is transported over OTN,
including PCS 64B/66B coded information, inter-frame ller (IPG), MAC FCS, preamble, start of frame delimiter (SFD) and ordered sets (remote
fault indication). The OTN clocking in this scenario is derived from the Ethernet customer signal (100 ppm) rather than that of a standard OTU2
signal (20 ppm). Therefore, standard methods for control of jitter and wanderaccording to G.8251do not apply in this case, thereby limiting
this application to point-to-point data paths.
6.1. OTU2e10GBASE-R Signal Mapping into OPU2e
The OTU2e (not to be confused with the OTU2, 10.709 Gbit/s signal standard) is a mapping mechanism that uses the mapping scheme of CBR 10
G signals into OPU2, dened in G.709 subclause 17.1.2. The 10GBase-R client signal with xed stuff bytes is accommodated into an OPU-like signal,
then further into an ODU-like signal, and then further into an OTU-like signal. These signals are denoted as OPU2e, ODU2e and OTU2e, respectively.
In the case where the original 10GBase-R input client signal has a different clock rate than the transport layer, a positive or negative bit stufng would
be required for adjustment. Typically, when the input client signal has a rate lower than the transport layer, positive stufng occurs and when the input
client signal has a higher rate, negative stufng occurs. The location of the stufng bits is communicated to the receiving end of the data link, where
these extra bits are removed to return the bit streams to their original bit rates or form. In this case, the OTU2e signal must be clocked at nominal
bit rate of 11.0957 Gbit/s. A unique payload type (PT)0x80 reserved code for proprietaryis specied in the payload structure identier (PSI).
Table 6.1 Overclocked OTN rates
6.2. OTU1e10GBASE-R Signal Mapping into OPU1e
The OTU1e (not to be confused with OTU1 which is a 2.7 Gbit/s signal) is a mechanism that maps CBR2G5 signals into OPU2 as previously
described. However, the xed stuff bytes of the CBR 10 G mapping are not left free in this mechanism, making the overall data rate somewhat
less (11.0491 Gbit/s rather than 11.0957 Gbit/s). Again, the clock tolerance of the underlying Ethernet signal is 100 ppm rather than the
20 ppm of a standard OTU2 signal. Therefore, standard methods for control of jitter and wander according to G.8251 do not apply again in this
case. A unique PT shall be specied in the PSI, e.g., code 0x80 (reserved code for proprietary use).
6.3. GFP-F Mapping of 10GBASE-R into OPU2
Generic framing procedure (GFP) is another mechanism for transporting 10 GbE LAN
or WAN client signals over OTN. GFP-F encapsulates 10 GbE frames into GFP-F
frames rst and then into OTU2, according to the G.709 subclause 7.3; GFP-F maps
the Ethernet MAC trafc, eliminating the 64B/66B PCS sub-layer. In addition, mapping
the GFP-F frames into OPU2 uses the entire OPU2 payload area, meaning that the
xed stuff bytes of the CBR 10 G mapping are not present. Finally, the key benet of
using GFP-F over OTN is to support various data-packet services on the same network.
6.4. ODU2e Signal Mapping into ODU3e
The necessity for network engineers to multiplex 10 Gigabit Ethernet signals directly
mapped over OTN led to introduction of the overclocked OTU3e. The OTU3e is a
mechanism that allows 10Gig-E LAN signals to be carried directly over 40G OTN
networks. Multiplexing ODU2e in OTU3e provides granularity of the 40G circuits,
optimizing the payload and simplifying network provisioning and maintenance. The frame
structure of the OTU3e2, ODU3e2 and OPU3e2 are the same frame structures as the
frame structures of the OTUk, ODUk and OPUk specied in ITU-T G.709. The OPU3e2
carries one or more ODUj (j=2e) signals.
ODU OH
FAS
OTU
OH
OPU Playload OPU Playload FEC
Fixed
Stuff
Bytes
1
1
2
3
4
7 8 14 15 16 17 4080 3824 3825
1
9
0
5
1
9
0
4
1
9
2
1
1
9
2
0
O
P
U

O
H
OTU2e
11.0957G 10.3125G
(10GE LAN PHY)
OTU2e OTU2e
Fixed
Stuffing
Client
Payload
ODU OH
FAS
OTU
OH
OPU Playload FEC
1
1
2
3
4
7 8 14 15 16 17 4080 3824 3825
O
P
U

O
H
OTU1e
11.0957G 10.3125G
(10GE LAN PHY)
OTU1e OTU1e
Client
Payload
Figure 6.3 Overclocked OTN without Stufng
Figure 6.2 Overclocked OTN with Fixed Stufng
7
Testing Optical Transport
Network Elements
7. Testing Optical Transport
Network Elements
Of course, as with every type of network, testing always
ensures optimum performance. Among the tests that should
be carried out in order for OTN equipment to comply with
ITU-T G.709 and ITU-T G.798 are the following:
Interface specications test
Response test
Conformance and interoperability test
Mapping/demapping of client signals test
Appropriate FEC behavior test
ODU1 to ODU2 multiplexing
7.1. Interface Specications Test
The interface specications test is essential to ensure the proper interoperability of equipment from single as well as multiple vendors. The main
objective of this test is to verify the input parameters of all interfaces of the G.709 network element under test, including the appropriate OTUk
rate, and ensure that synchronization recovery can be properly achieved.
In the interface specication test conguration shown in Figure 7.1 Interface Specications Test Conguration, the synchronization to the
incoming signal must rst be checked. For example, clock deviation has to be checked for OTU1 and OTU2 interfaces to ensure its within the
dened 20 ppm value.
Figure 7.1 Interface Specications Test Conguration
Additional tests like optical power sensitivity can
also be achieved using an optical attenuator to
reduce the optical power until the threshold of
the input receiver is reached and an optical power
meter can be used to measure the minimum
supported optical input power.
7.2. Response Test
The network element response test involves
sending a stimulus (error or alarm) signal into
the device under test (DUT) and monitoring its
appropriate output and proper consequence.
In OTN, a single stimulus may result in several
simultaneous responses. The example shown in
Figure 7.2 DUT Response Test Conguration
illustrates the test setup and expected responses
to a detected loss of signal (LOS) at the receiver.
The response test must be repeated for all
possible input stimuli that the DUT is expected
to respond to. A list of possible stimuli and
their corresponding responses (alarm/error) by
the network element under test in upstream and
downstream directions are shown in Table 7.1.
Figure 7.2 DUT Response Test Conguration
Table 7.1 Stimulus and DUT Response
Stimulus
Upstream
Alarm/Error
Downstream
Alarm/Error
LOS-P, LOF, AIS-P, LOM OTU BDI OTU-AIS
OTU BIP-8 OTU BEI
OTU TIM OTU BDI OTU-AIS
OTU IAE OTU BIAE
ODU AIS ODU BDI ODU AIS
ODU BIP-8 ODU BEI
ODU TIM ODU BDI
ODU OCI ODU BDI ODU AIS
ODU PLM ODU AIS
7.3. Conformance and Interoperability Test
The ITU conformance and interoperability test determines the
DUTs ability to detect various events under the correct stimulation
and standard-specied period of time. Standards normally dene
entry and exit criteria for alarm events, usually specied by a
number of frames or sometimes in a time period. In a similar
conguration to the DUT response test shown in Figure 7.2, it
is recommended to simulate a stimulus condition (alarm/error)
over variable test periods. This allows an alarm condition to be
simulated for a variable number of frames and to conrm that the
entry and exit criteria are met precisely.
7.4. Client Signal Mapping Test
The optical transport hierarchy standard has been designed to
transport a range of synchronous and asynchronous payloads.
Using OTN decoupled mode, as shown in Figure 7.3 Client
Signal Mapping Test Conguration, allows the user to generate a
SONET/SDH client signal in the transmit direction and verify the
received OTN signal with the mapped SONET/SDH client signal.
This conguration enables the test equipment to determine if the
DUT successfully recovers the OPU payload under the mapping
specications. When mapping SDH/SONET signal into the OPU,
rate differences between the client signal and the OPU clock are
accommodated through the use of justication (stufng) bytes.
The demapping process of a client signal can also be veried
in the opposite direction. Using the OTN decoupled mode
again, the test equipment can be used to generate an OTN
signal with a mapped SONET/SDH client signal on the
transmit side and verify the demapped SONET/SDH client
signal at the transponder under test.
7.5. Appropriate FEC Behavior Test
As forward error correction (FEC) is a key element of OTN
and is used for improving the quality of service, it needs to be
validated as part of the G.709 testing. In order to determine
the appropriate FEC behavior of the DUT, the test equipment
would be used to generate correctable or uncorrectable
errors, which would be transmitted through the OTN network
element. At the receiving end, the received OTN signal
is checked to determine whether or not the errors were
corrected or at least detected by the DUT.
This test is performed, as shown in Figure 7.4 Appropriate FEC Behavior Test Conguration, by inserting varying numbers of errors distributed
over the FEC portion of the OTN frame and checking the error-correction capability of the DUT. This facilitates the discovery of unexpected
behavior without affecting the trafc. An advanced FEC behavior test can be performed by distributing correctable errors at random over the entire
OTU frame, which should be recovered by the DUT. If not, then the payload will be affected in this case.
Figure 7.3 Client Signal Mapping Test Conguration
7.6. ODU1 to ODU2 Multiplexing
ODU1 to ODU2 multiplex functionality testing is also a key parameter
that needs to be validated as part of G.709. In order to determine the
appropriate multiplexing capability of the network element under test,
the test equipment is used in OTN decoupled mode to generate either
an OC-48/STM-16 signal or an OTU1 signal on the transmit side. The
transmitted signal then gets multiplexed within an ODU2 signal on the
G.709 network element with the proper overhead and FEC bandwidth
to compose the nal OTU2 signal. Finally, the received OTU2 signal is
checked at the test equipment to verify the ODU1 to ODU2 multiplexing
with the proper with frequency justication and synchronization as shown in
Figure 7.5 ODU1 to ODU2 Multiplexing Test Conguration.
7.7. ODU0 to OTU2 Multiplexing
Mapping GigE service into ODU0 is key for qualifying the container as
part of a multiplatform network. When performing this test, it is extremely
important that the Expected Payload Type (PT) congured at the destination
match the Injected Payload Type at the source to obtain full access to Gig-E
statistics.
Figure 7.4 Appropriate FEC Behavior Test Conguration
Figure 7.5 ODU1 to ODU2 Multiplexing Test Conguration
7.8. OTN as a Service
In todays transport networks, OTN is being used from the core to the edge. At the core, OTN is used to transport high speed rates of 10, 40 and
100 Gbit/s. In edge networks, where it is just starting to gain momentum, OTN offers a multitude of benets to both operators and customers alike.
Among the many advantages, it offers complete end-to-end performance monitoring throughout the entire network rather than just at the edge,
thereby providing robust alarm and error monitoring. Here are a few more advantages that service providers should be aware of:

Flexibility of services (e.g., you can have 10 Gigabit Ethernet or OC 192/STM-64 over an OTU2 service, or even higher Gigabit Ethernet in an
OTU0 without burning bandwidth).

OTN can be used to transport legacy services, but also allows for convergence to MEF Carrier Ethernet 2.0. Accordingly, it can be qualied as
a pay-as-you-grow architecture.

OTN has built-in OAM capabilities that far exceed some legacy technologies, meaning that it improves quality of service (QoS).
As a service, OTN offers improved exibility for optimization of the transport container through the addition of lower-order ODU0 and ODUex
containers. (For more information about ODU0 and ODUex, please see their respective sections in this pocket guide.) And, with the help of a
new generic mapping procedure (GMP), the ex concept optimizes client mapping of any bit rate into any larger bit-rate container without the need
for unique mappings for each client/container pair. GMP is used for mapping transcoded 1 Gigabit Ethernet or any constant bit rate trafc into an
OPU0 or ODUex, all the way up to a higher-order OPU4. As previously described, the exibility and efciency of OTN circuits is very attractive to
service providers who are planning to expand into new revenue streams and offer more services. Figure 7.8.1 below details the transparency and
exibility offered by OTN, which is now optimized to support any client signal.
7.8.1 Todays OTN structure
The same test that used to be located in the metro and edge will now need to be performed on the access side, introducing new challenges for
technicians who are used to working with Ethernet, IP, Fiber Channel (FC), SONET/SDH and other technologies. Some of these challenges are
as follows:

The need to develop new service turn-up procedures

Training and educating eld technicians in OTN technology

Test equipment availability

Testing and troubleshooting procedures
As shown in Figure 7.8.2, the new challenges extend from one end of the network to the other, but can be reduced with the appropriate test
equipment offering a simple user interface and support for a wide range of of client signals, including SONET/SDH, FC, ETHERNET and OTN.
As an added benet, an all-in-one test equipment solution will also reduce the technician learning curve, which translates into reduced costs for
carriers and service providers.
Figure 7.8.2 End-to-end OTN test conguration
8
Conclusion
8. Conclusion
To satisfy the growing demand for bandwidth, control costs and still remain competitive, service providers are deploying the next-generation
optical transport networks dened by ITU-T G.709. The G.709 technology includes forward error correction and enhanced network management,
delivering a function comparable to the effect of SONET/SDH on a single wavelength with full transparency.
Today, service providers are faced with the challenge of building up their condence in the new OTN network and its promised improved
performance to the end users. This is made possible with the introduction of the G.709 testing capabilities in the test and measurement market.
Service providers are now equipped with the full spectrum of G.709 testing equipment for lab standardization, interoperability testing, eld
deployment and troubleshooting.
9
Acronyms
9. Acronyms
APS Automatic Protection Switching
AIS Alarm Indication Signal
BDI Backward Defect Indication
BEI Backward Error Indication
BIP-8 Bit-Interleaved Parity-8
BIAE Backward Incoming Alignment Error
CSF Client Signal Fail
DAPI Destination Access Point Identier
DUT Device Under Test
DWDM Dense Wavelength-Division Multiplexing
DW Digital Wrapper
EXP Experimental
FEC Forward Error Correction
FTFL Fault Type Fault Location
FAS Frame Alignment Signal
GFP Generic Framing Procedure
GCC General Communication Channel
IaDI Intra-Domain Interface
IrDI Inter-Domain Interface
IAE Incoming Alignment Error
LOF Loss of Frame
LOFLOM Loss of Frame and Loss of Multi-Frame
LOL Loss of Lane Alignment
LOOMFI Loss of OPU Multi-Frame Identier
LOR Loss of Recovery
LOS Loss of Signal
LCK Locked
MFAS Multiframe Alignment Signal
MSI Multiplex Structure Identier
NE Network Element
OCh Optical Channel
OH Overhead
OLA Optical Attenuator
OLP Optical Power Meter
OMFI OPU Multi-Frame Identier
OOR Out of Recovery
OPU Optical Channel Payload Unit
OTN Optical Transport Network
OTU Optical Channel Transport Unit
OMS Optical Multiplexing Section
OTS Optical Transmission Section
OSC Optical Supervisory Channel
ODU Optical Channel Data Unit
OAM&P Operations, Administration, Maintenance & Provisioning
OADM Optical Add/Drop Multiplexer
OOF Out of Frame
OOM Out of Multiframe
OCI Open Connection Indication
OSNR Optical Signal-to-Noise Ratio
PSI Payload Structure Identier
PCC Protection Communication Channel
PM Performance Monitoring
PT Payload Type
PRBS Pseudo-Random Bit Sequence
PMD Polarization Mode Distortion
RS Reed Solomon
RES Reserved
SAPI Source Access Point Identier
SM Section Monitoring
SONET Synchronous Optical Network
SDH Synchronous Digital Hierarchy
STAT Status
TCM Tandem Connection Monitoring
TTI Trail Trace Identier
NOTES
NOTES
2013 EXFO Inc., Quebec City, Canada. All Rights Reserved.
OTN (G.709) Reference Guide, 4
th
edition
No part of this guide may be repoduced in any form
or by any means without the prior written permission of EXFO.
Printed and bound in Canada
ISBN 1-55342-008-X
Legal DepositNational Library of Canada 2007
Legal DepositNational Library of Quebec 2007
For details on any of our products and
services, or to download technical and
application notes, visit our website at
www.EXFO.com.
O
T
N
-
G
-
7
0
9
.
4
A
N
A
N

1
3
/
0
4

2
0
1
2
0
7
7
4

S
A
P

1
0
6
3
1
0
8

Reference Guide OTN

Uploaded by

Copyright:

Available Formats

Reference Guide OTN

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Reference Guide OTN

Uploaded by

Copyright:

Available Formats

OTN (G.

709) Reference Guide

You might also like