Coldweatheroperations 2011 20

ATR CUSTOMER SERVICES
COLD
WEATHER
OPERATI ONS
BE PREPARED FOR I CING
Important notice
This brochure is intended to provide general information regarding flying in icing conditions.
In no case it is intended to replace the operational and flight manuals for ATR aircraft.
In all events, the procedures describe in the Aircraft Flight Manual
shall prevail over the information contained in this document.
P
r
i
n
t
e
d

o
n

1
0
0
%

r
e
c
y
c
l
e
d

p
a
p
e
r

u
s
i
n
g

v
e
g
e
t
a
b
l
e

i
n
k
s
Col d weat her operat i ons
All efforts have been made to ensure the quality of the present document.
However do not hesitate to inform ATR Flight Operations support of your comments
at the following address: [email protected]
The Flight Operations Support team
3
Introduction
Introduction
Icing is an adverse atmospheric phenomenon, and
remains very harmful to air transport. Flying in icing
condi ti ons i s consi dered a seri ous threat, and
concerns every airline all around the world. Operating in hot countries, does not prevent one from
encountering icing conditions in flight: 30C at sea level means 0C at FL150. Due to prevailing atmospheric
conditions at their operating flight levels, turboprop aircraft fly where icing conditions are most likely to occur.
Flight crews must always be prepared to face icing, as this leads to uncomfortable flight characteristics,
like speed and/or rate of climb losses.
Cold Weather Operations brochure is intended to provide ATR operators with a thorough understanding of
ATR aircraft operations in Cold Weather conditions, and develops such aspects as:
Meteorological icing phenomena
Systems available to prevent and control ice accumulation, including the Aircraft Performance Monitoring
(APM) system. This system embodies low speed warning devices enhancing crew awareness, in case
of severe icing encounters.
Performance loss due to ice contamination on aircrafts aerodynamic surface
On ground and in-flight applicable procedures when facing icing conditions.
This current release of Cold Weather Operations brochure includes at the end a Quizz to evaluate good
practices and aeronautical decision making, when having to deal with icing conditions in flight.
Introduction
4
Introduction........................................................................................................................................................3
Chapter A Weather revision on Icing ..................................................6
A.1. What is icing?..........................................................................................................................................7
A.2. Build-up process ..................................................................................................................................7
A.2.1. Supercooled water droplets.........................................................................................7
A.2.2. Freezing of liquid water ....................................................................................................7
A.2.3. Condensation from vapor to ice.............................................................................7
A.2.4. Types of accretion...................................................................................................................7
A.2.5. Factors affecting the severity of icing .........................................................11
A.3. Icing classification...........................................................................................................................12
A.3.1. Quantitative classification............................................................................................12
A.3.2. Severity of ice ............................................................................................................................13
A.4. Some typical clouds......................................................................................................................14
Chapter B Weather documentation ......................................................15
B.1. Available means .................................................................................................................................16
B.2. TAF/METAR/SPECI/TREND interpretation...........................................................16
B.3. AIRMET/SIGMET................................................................................................................................17
B.4. Weather charts....................................................................................................................................17
Chapter C Aircraft de-/anti-icing ...............................................................19
C.1. Some questions to answer before de-icing.....................................................20
C.2. Basics.............................................................................................................................................................20
C.2.1. Definitions.......................................................................................................................................20
C.2.2. Equipment and material.................................................................................................21
C.2.3. Fluid selection ...........................................................................................................................21
C.3. De-icing and anti-icing procedures............................................................................23
C.3.1. Aircraft preparation .............................................................................................................23
C.3.2. Procedures ....................................................................................................................................23
C.3.3. Hotel mode....................................................................................................................................24
C.4. Fluid residues .......................................................................................................................................24
C.5. Captains decision...........................................................................................................................25
C.6. Anti-icing codes.................................................................................................................................25
C.7. Holdover time .......................................................................................................................................26
C.7.1. Estimated holdover times for Type I fluid mixtures ....................26
C.7.2. Estimated holdover times for Type II fluid mixtures...................27
C.7.3. Estimated holdover times for Type IV fluid mixtures.................28
Chapter D Aircraft ice protection systems...........................29
D.1. Systems description .....................................................................................................................30
D.1.1. Electrical System....................................................................................................................30
D.1.2. Pneumatic System................................................................................................................31
D.1.3. Aircraft Performance Monitoring ........................................................................31
D.2. Systems operations.......................................................................................................................31
D.2.1. Ice accretion monitoring...............................................................................................31
D.2.2. Enhanced Ice accretion monitoring with the APM .......................33
Chapter E Performance .................................................................................................34
E.1. Impact of contamination by ice or snow ............................................................35
E.1.1. Lift ............................................................................................................................................................35
E.1.2. Drag........................................................................................................................................................35
E.1.3. Performance .................................................................................................................................36
E.1.4. Handling.............................................................................................................................................36
E.2. Documentation provided by ATR...................................................................................36
E.3. Performance on contaminated runways ...............................................................37
E.3.1. What is a contaminated runway?.......................................................................38
E.3.2. Braking means...........................................................................................................................38
Contents
5
Contents
E.3.3. Braking performance .........................................................................................................38
E.3.4. Correlation between reported and
braking performance .........................................................................................................39
E.3.5. Aircraft directional control ..........................................................................................39
E.4. Aircraft braking means ..............................................................................................................39
E.4.1. Wheel brakes...............................................................................................................................39
E.4.2. Reverse thrust............................................................................................................................40
E.5. Braking performance....................................................................................................................41
E.5.1. Influence of the contaminants................................................................................41
E.5.2. Reduction of the friction coefficient .........................................................42
E.5.3. Precipitation drag...................................................................................................................43
E.5.4. Aquaplaning ................................................................................................................................43
E.6. Correlation between reported and braking performance...........43
E.6.1. Information provided by airport authorities............................................43
E.6.2. Difficulties in assessing the effective ......................................................45
E.6.3. Data provided by ATR......................................................................................................46
E.7. Aircraft directional control.....................................................................................................46
E.7.1. Influence of slip ratio ........................................................................................................46
E.7.2. Influence of wheel yaw angle .................................................................................47
E.7.3. Ground controllability ........................................................................................................47
E.8. Performance determination ..................................................................................................47
Chapter F Procedures.......................................................................................................49
F.1. Parking...........................................................................................................................................................50
F.2. Exterior inspection...........................................................................................................................50
F.2.1. Walk-around..................................................................................................................................50
F.2.2. Frost due to condensation..........................................................................................50
F.3. Cockpit preparation .......................................................................................................................51
F.3.1. Cold weather operation ..................................................................................................51
F.3.2. Permanent anti-icing ..........................................................................................................51
F.4. Taxi ....................................................................................................................................................................51
F.4.1. Taxi procedures........................................................................................................................51
F.4.2. Caution................................................................................................................................................51
F.5. Take-off.........................................................................................................................................................52
F.5.1. Take-off in atmospheric icing conditions..................................................52
F.5.2. Take-off on contaminated runways..................................................................52
F.5.3. Fluid type II and fluid type IV particularities .........................................52
F.6. Flight profile in icing conditions .....................................................................................54
F.6.1. Entering icing conditions...............................................................................................54
F.6.2. At 1st visual indication of ice accretion and
as long as icing conditions exist .......................................................................55
F.6.3. Leaving icing conditions ................................................................................................57
F.6.4. When the aircraft is visually verified clear of ice............................57
F.7. Procedures following APM alerts..................................................................................58
Chapter G Severe icing..................................................................................................59
G.1. Overview .....................................................................................................................................................60
G.1.1. Supercooled large droplet ..........................................................................................60
G.1.2. Temperature inversion.....................................................................................................60
G.1.3. Collision-coalescence process..............................................................................60
G.2. Detection of SLD..............................................................................................................................61
G.2.1. Conditions conducive to SLD .................................................................................61
G.2.2. Visual Cues ...................................................................................................................................61
G.3. Procedure..................................................................................................................................................62
Appendices ......................................................................................................................................................64
Appendix 1. Quizz.........................................................................................................................................65
Appendix 2. Definitions...........................................................................................................................67
Appendix 3. Abbreviations..................................................................................................................71
Contents
6 A. Weather revision on icing
A. Weather
revision on icing
7 A. Weather revision on icing
A. Weather revision on icing
1. What is icing?
Icing is defined by any deposit or coating of ice on an object caused by the impact of liquid hydrometeors
usually supercooled. This phenomenon generally occurs first on parts exposed to relative wind (i.e. probes,
antennas, leading edge...)
Supercooled water is a physical state where liquid water exists below its normal freezing point without freezing.
2. Build up process
Ice can form by three processes described below. At least one of them is involved whatever the weather situation.
2.1. Supercooled water droplets
Large quantities of supercooled water are present in the atmosphere, basically in clouds and freezing precipitation.
Ice deposits on airframe are directly related to super-
cooled water concentration in atmosphere, size of drop-
lets and precipitation intensity.
This phenomenon appears when it is raining in very cold air.
2.2. Freezing of liquid water
This case occurs when liquid water, at positive temperature remains on exterior parts of the airplane, typically scratch
on skin, landing gear case, probes and control surfaces gap.
This water is very likely to freeze as soon as the aircraft enters a very low temperature atmosphere after uncompleted
snow removal on ground for instance.
2.3. Condensation from vapor to ice
This is a transition from the vapor phase directly to the solid phase.
This phenomenon is likely to occur outside the clouds in a high moisture atmosphere on an aircraft with
particularly cold skin. This case typically happens while aircraft is descending from its cruise flight level.
2.4. Types of accretion
This classification refers to the aspect of the accretion. It depends on several factors among them:
Quantity of supercooled water droplets (Liquid Water Content)
Size of droplets (diameter and distribution)
Environment
Outside Air Temperature (OAT)
Freezing rain
T air >0C
T air <0C
T air <0C
T air >0C
T air <0C
T air >0C
8
2.4.1. Hoar frost
Deposit of ice, which generally assumes the form of scales, needles, feathers or fans and which forms on objects whose
surface is sufficiently cooled, to bring about the direct sublimation of water vapor contained in the ambient air.
Build up process
Condensation, that is to say direct transformation of vapor to ice. This phenomenon occurs with negative
temperatures. Ice accretion appears on ground with a parked plane or in flight, particularly during descent
with a cold airplane.
Associated weather conditions
On ground
Anticyclonic conditions in winter, with clear night skies and
little wind, can cause a sharp drop in ground temperature,
which leads to formation of hoar frost on an aircraft parked
outside overnight.
As whole airframe upper surfaces may be affected, the aircraft
has to be cleaned of any ice accumulation prior to take-off.
In flight
Hoar frost can form on an aircraft, which was parked in a cold
area and quickly climbs to a warm moist atmosphere.
It can also form on an aircraft which has flown in a cold area
and quickly descends into a warm moist atmosphere. Air in
contact with the cold aircraft skin freezes quickly producing
hoar frost.
Consequence
Hoar frost generally leads to light icing conditions with little effects on aerodynamic qualities.
2.4.2. Rime ice

Rime ice on a leading edge
Rime ice has a milky, opaque appearance. It forms when the liquid water droplets freeze on impact. This usually occurs
at low temperature or when the liquid water content is low.
Build up process
Fast freezing process of very small-supercooled water droplets in stable clouds layer.
This kind of icing builds up on parts exposed to the relative wind. The capture of little air bubbles during the
freezing process gives rime ice its opaque aspect. The accretion grows up forward.
Skin temperature <0 C
T air <0 C
Skin temperature
<0 C
t
air
upper level > t
air
lower level
+ saturated air
Build up direction
Streamlines
9
Rime ice builds up in stable clouds layer like As and Ns of cold and warm fronts of
polar fronts.
Consequence
Rime ice also builds up in radiation fog at negative temperature in high pressure area in winter.
Rime ice formations generally conform with the shape of the airfoil leading edge, causing less
disruption in the airflow at sufficiently low AOA and therefore fewer handling and perform-
ance problems than clear ice.
2.4.3. Clear ice
Clear ice can be lumpy and translucent or clear and smooth.

Clear ice on a leading edge
Build up process
Slow freezing of supercooled water droplets in stable or unstable clouds with high liquid water content. The range of
temperature allowing this process comes from 0 C to 10 C.
At impact a supercooled water droplet spreads on the
airplane skin and freezes, conforming plane shapes.
No air bubbles are captured during the process giving clear
ice a compact texture and a transparent aspect.
This kind of icing generally grows up backward, conforming
plane shapes or with a double horn shape.
Clear ice forms in cloud layers with high liquid water content:
Very unstable clouds along cold and warm fronts of polar fronts: cumulonimbus and very unstable altocumulus
Freezing rain
T air >0C
T air <0C
T air <0C
T air >0C
T air <0C
T air >0C
Orographic lifting: Cb and very unstable Ac
The orographic effect of a range of hills is likely to increase uplift in cloud so that the concentration and
size of the supercooled water droplets are increased.
Convective clouds and rear of depression.
Flow
down
Build up direction
Streamlines
Airfoil
10
Dense fog and stratus
Due to the high disparity of droplet size inside a cloud layer, ice accretion is a non-homogeneous process. Thus
rime ice and clear ice accrete alternatively forming mixed ice.
Rime ice
Clear ice
Iso 0C in instable
saturated air
Iso 0C in stable
saturated air
Consequence
The relatively slow freezing process can lead to the formation of horns and other shapes that can dramatically disrupt
airflow and lead to substancial decrements in performance and handling. Clear ice accretion is very dangerous and
is generally associated with severe icing conditions.
2.4.4. Mixed ice
Mixed ice forms at conditions between rime and clear ice in that it may form horns or other shapes that
disrupt airflow and cause handling and performance degradations.
Mixed ice on a leading edge
2.4.5. Glaze
Glaze ice is very close in shape, texture and aspect to clear ice. The essential difference lies on the freezing
mechanism.
A smooth compact deposit of ice, generally transparent, formed by the freezing of supercooled drizzle droplets
or rain drops on aircraft skin with a temperature slightly above 0 C
Build up process
Glaze builds up through a condensation process of drizzle or raindrop. At impact a big supercooled water
droplet spreads on the aircraft skin and freezes, conforming to plane shapes.
Glaze could also build up on a aircraft with a very cold skin under rain at positive temperature. In this case,
the phenomenon has a short duration.
Presence of supercooled precipitations is a regular
phenomenon along frontal surfaces:
Glaze accretion area is wider under warm front
The higher the temperature difference between cold
and warm air, the thicker the glaze accretion area
Glaze accretion areas are more dangerous in winter
than in summer
Glaze accretion areas are likely to appear inside occlu-
sions
T air > 0C
T air < 0C
Freezing rain Skin temperature < 0C
No deposit Clear or glaze ice
11
W
i
n
d

v
e
r
t
i
c
a
l

s
p
e
e
d

(
m
.
s
-
1
)

Time in seconds
Time in seconds
Q
u
a
n
t
i
t
y

o
f

l
i
q
u
i
d

w
a
t
e
r

(
g
.
m
-
3
)
Updraft
In winter on ground or at low level, freezing rain can form when the rain follows an anticy-
clonic period. Air close to the surface in valleys remains very cold, freezing rain is formed
when water droplets pass through this layer.
Special case: glaze in Cb. Due to lifting currents inside the cloud, supercooled precipitations
could strike a plane flying above freezing level from the bottom.
Consequence
Glaze is likely to induce severe icing. This type of icing is not only dangerous because the speed of accretion
is fast, but also because the entire airframe is affected.
In this situation the de-icing system is inefficient.
2.5. Factors affecting the severity of icing
Icing intensity is directly related to the supercooled water quantity available.
In addition, the speed of accretion is linked to the size of the supercooled water droplets, which depends on
several factors among them:
Cloud type
Air in vertical motion
Horizontal distribution of water content
Streamline
NOTE: The stronger the updrafts, the more the atmosphere contains liquid water. The previous diagrams show this phenomenon.
12
Dry build up
Clean airfoil
Contaminated surface Clean surface
Temperature at stagnation point
Sudden increase of the drag
Leading edge
Drag coefficient
Cx
Consequently if an aircraft flies through such an area while in icing condition, ice accretion will be important.
Nevertheless, the speed of accretion, the shape and the texture
depend on the speed of the aircraft through the medium.
3. Icing classification
Two kinds of classifications are relevant:
The first one quantifies the severity as a function of the atmosphere and is used by meteorologists.
The second one connects synoptic charts to practical solutions.
3.1. Quantitative classification
Lets have a look at the standard water content of some typical atmospheric mediums.
Nevertheless the water content of clouds is a non-uniform value.
The following table shows the relationship between the supercooled water content in the atmosphere and the
icing potential as it is presented on weather charts.
This table shows also that a same type of cloud could lead to different intensity of icing.
Symbol Supercooled water content in g/m
3
Corresponding clouds
Light Less than 0.6 As, Ns, stable Sc
Fog and light St
Quite stable Ac
Moderate From 0.6 to 1.2 Dense fog
Dense St
Ns
Ac, unstable Sc, Cu, Cb
Severe Above 1.2
Out of certification
Exceptional fog and St
Very unstable Ac, Cu, Cb
Heavy freezing rain
Medium to 3 Water content in g/m
3

Fog 0.1 to 2
Stable clouds 0.2 to 0.5
Unstable clouds 1
L
W
C

(
g
.
m
-
3
)
D
V

(
m
)
Droplet diameter
Water content
Results obtained crossing a cumulus congestus at 10C
13
Flight tests have demonstrated that the most favorable temperatures for icing are:
From 0 C to 10 C in stable clouds with an important decrease in intensity under 18 C
From 0 C to 15 C in unstable clouds, but presence of ice down to 30 C
Ice accretion varies widely depending on the severity of icing: from less than 1 cm per hour to several cm
per minute in Cb, Cu or heavy freezing rain.
3.2. Severity of ice
To standardize the reporting of the severity of icing encounters, 4 levels of icing severity have been defined:
Trace icing
Light icing
Moderate icing
Severe icing
Trace icing
Ice becomes perceptible. Rate of accumulation is slightly greater than the rate of sublimation.
Pilot action recommendation:
Monitor the situation, the icing severity could increase.
Light icing
Light ice indicates that the rate of accumulation is such that occasional use of ice protection systems is
required to remove or prevent accumulation (1 cm in 15-60 minutes).
The rate of accumulation may create a problem if flight is prolonged in this environment (over 1 hour). If in
rime conditions, the accumulation on the leading edge appears as a band several centimeters wide. If clear
or glaze, roughened edges may start to appear.
This is a potentially hazardous condition. Either activate the ice protection system or exit the conditions.
Moderate icing
Moderate ice indicates that frequent use of ice protection systems is necessary to remove or prevent ice
(1 cm in 5-15 minutes).
Unless actions are taken, substancial amounts of ice will build up on the airfoil. At this intensity, the rate of
accumulation may present a problem even with short encounter.
This is a potential hazardous condition. Activate the ice protection systems to control ice accretion while
exiting the conditions.
Severe icing
Severe icing indicates that the rate of accumulation is so fast that ice protection systems fail to remove the
accumulation of ice (1 cm in less than 5 minutes). The crew need to exit this condition immediately.
Severe icing is usually a product of clear or mixed icing encounter. Severe icing occurs most frequently in
areas where the air has high content of liquid water or there are very large droplets.
Immediate pilot action is required. Performance and handling may be seriously affected after only a few minutes
exposure. Activate the ice protection system and work to exit the conditions immediately.
14
4. Some typical clouds

This situation is prone
to icing. Low level
stratus and other
grey clouds may
have a high
water content.
Although the grey clouds
contain supercooled
liquid water, the situation
is too windy to be
a big icing threat except
inside the cumulonimbus.
This type of cumulus
congestus may
hide severe
intermittent icing.
This type of thick stratus
looking like heavy
soup with a mountain
blockage, may be
a threat for icing.
B. Weather
documentation
B. Weather documentation 15
Weather analysis is one of the most important aspects of flight preparation. It may become critical for
particularly demanding conditions where potential icing conditions could be encountered. Typical weather
forecast provided to pilots at flight preparation includes several documents which will be discussed in the
following chapter.
1. Available means
TAF, METAR, SPECI and TREND collection
The crew should collect such information for all airports of interest including the ones along the planned route.
These information might be essential in deciding whether the flight has to be re-planned via another route.
Sigmets and Airmets collection
This will alert the crew of areas of forecast or reported moderate and severe icing.
Significant weather charts collection
This is an invaluable mean for assisting the crew in forecasting possible areas of icing conditions or precipitation.
Snotams
These information will complete the picture and assist the crew in developing any alternate or contingency
plan.
2. TAF/METAR/SPECI/TREND interpretation
TAFs are meteorological forecasting at airports.
METARs are routine meteorological observations at airports. Usually they are issued each 30 or 60 minutes.
SPECIs are special meteorological observation reports. They are issued at a given airport if:
Meteorological conditions are worse than the last METAR
Meteorological conditions have improved and improvement has lasted for at least 10 minutes
TREND is a section included in a METAR or a SPECI providing information on the evolution of meteorological
conditions. It is issued if a variation of wind, visibility, weather or cloud phenomenon is expected. The validity
of a trend is 2 hours starting from the associated METAR or SPECI time.
Example of METAR message
LFB0 10 1000Z VRB 03KT 0500 FZFG VV/// M02/ M02 Q1025
This METAR is the typical example of ground icing conditions in winter:
low visibility with moisture, freezing fog and OAT below 5C.
Airport
identification
Date (day)
Time of issue
Wind < 3 KT
Wind
velocity
Horizontal
visibility
Weather
significant:
Freezing fog
Cloud layout
altitude
OAT
Dew point
QNH
B. Weather documentation
3. AIRMET/SIGMET
AIRMET
In-flight weather advisories concerning phenomena of operational interest to all aircraft and potentially hazardous
to aircraft having limited capabilities. AIRMETs are issued every six hours with amendments as needed and cover
moderate icing, moderate turbulence, sustained surface winds of 30 knots or more, extensive mountain obscuration,
and widespread areas of ceilings less than 1000 feet and/or visibility less than 3 miles.
SIGMET
In-flight weather advisory concerning phenomena of an intensity and extent that concerns the safety of all
aircraft. SIGMETs cover severe and extreme turbulence, severe icing, volcanic ash and widespread dust or
sandstorms that reduce visibility to less than 3 miles. CONVECTIVE SIGMETs advise of thunderstorms that
are potentially hazardous to all aircraft. Information contained in SIGMETs depends on the cruise level:
Example of TAF message
LFB0 150500Z 150615 360 03KT 0800 FZFG OVC002
Airport
identification
Date (day)
Time of issue Wind
direction
Wind
velocity
Horizontal
visibility (800 m)
Cloud layer
altitude
Validity (on the
15th between
06 and 15 TU)
Weather
significant:
Freezing fog
AIRMET/SIGMET
At subsonic cruising levels At transonic level and supersonic cruising levels
Thunderstorm (OBCS. EMBD, SQL, FRQ) - TS
Tropical cyclone - TC (+cyclone name)
Thunderstorm with heavy hail - TS HVYGR
Severe turbulence - SEV TURB
Severe icing and severe icing due to freezing
rain -SEV ICE, SEV ICE (FZRA)
Severe mountain waves - SEV MTW
Heavy sandstorm/duststorm - HVY SS/DS
Volcanic ash - VA (+volcano name)
Moderate or severe turbulence - MOD SEV TURB
Cumulonimbus clouds - (ISOL, OCNL, FRQ) CB
Hail - GR
Volcanic ash - VA (+volcano name)
4. Weather charts
Analyzed synoptic charts show the surface weather over a specified area. Prognostic synoptic charts aim to
show the expected synoptic situation some hours later, usually 12 or 24 hours ahead. Similarly, current and
prognostic charts are available for various pressure levels. In the briefing room the crew should find charts
covering low and medium flight over the UK and North West Europe, medium and high level flights to Europe
and the Mediterranean, low, medium and high level flights to North America, high level flights to the Middle
and Far East and high level flights to Africa.
Although these charts are less precise than TAF messages, they are very relevant in flight preparation. Because
of the wide area covered in comparison to all other means, they allow the crew to anticipate a weather
degradation and so to prepare a contingency flight plan. However information shown on such charts must
be always cross-checked with last Metar and TAF available for more accuracy.
This weather chart shows
typical icing conditions.
The associated vertical
representation gives
a picture of what crew
should expect during
the flight. Doing such
analysis is essential in the
briefing room to anticipate
a potential degradation
of meteorological conditions.
Actually having a good
overview of the location
of the 0 C level and cloud
layer allows the crew
to take the appropriate
decision to escape ice
accretion area, particularly
severe icing ones.
FL400
FL300
FL200
FL100
SFC
SCT LOC
OVC LOC BKN
ISO
LOC BKN
BKN
B A
Area where severe
icing is likely to appear
Thunder-
storm
Severe
icing
Mist
Moderate
turbulence
Fog Smoke
Strong
turbulence
Drizzle Rain
Icing Snow Showers
Moderate
icing
Freezing
rain
Hail
C. Aircraft
de-/anti-icing
C. Aircraft de-/anti-icing 19
Safe aircraft operation in cold weather conditions raises specific problems: Aircraft downtime and delays in
flight schedules. These can be minimized by a program of preventive cold weather servicing.
The operator must develop procedures for cold weather servicing which meet their specific requirements,
based on:
Their cold weather experience;
The available equipment and material;
The climatic conditions existing at their destinations.
Technical ATR documentation contains the appropriate
information to assist the operator in defining, developing
and implementing cold weather preventive maintenance
procedures that will minimize aircraft downtime and improve
the safe operating level of their aircraft in adverse climatic
conditions.
1. Some questions to answer before de-icing
Who is responsible?
The person technically releasing the aircraft is responsible for the performance and
verification of the results of the de-/anti-icing treatment. The responsibility of accepting
the performed treatment lies, however, with the Captain. The transfer of responsibility
takes place at the moment the aircraft starts moving under its own power.
When?
Icing conditions on ground can be expected when air temperatures approach or fall below freezing and when moisture
or ice occurs in the form of either precipitation or condensation.
Aircraft-related circumstances could also result in ice accretion, when humid air at temperatures above freezing comes
in contact with cold structure.
Clean aircraft concept
Any contamination of aircraft surfaces can lead to handling and control difficulties, performance losses and/
or mechanical damage.
De-icing?
Are the conditions of frost, ice, snow or slush such that de-icing is required to provide clean surfaces at engine start?
Anti-icing?
Is the risk of precipitation such that anti-icing is required to ensure clean surfaces at lift off?
Checks?
Do you have enough information and adequate knowledge to dispatch the aircraft?
2. Basics
2.1. Definitions
De-icing
De-icing is a procedure by which snow, frost, ice and slush are removed from aircraft in order to provide
clean surfaces. De-icing can be accomplished by use of fluids, by mechanical means or by heating the aircraft.

I
n
f
o
r
m
a
tion
C. Aircraft de-/anti-icing
Anti-icing
Anti-icing is a precautionary procedure which provides protection against
formation of frost or ice and accumulation of snow on treated surfaces of
the aircraft, for a limited period of time (holdover time).
De-icing/anti-icing process
De-icing and anti-icing may be performed as a one-step or two-step
process, depending on predetermined practices, prevailing weather condi-
tions, concentration of FPD (freezing point depressant) used, and available
de-icing equipment and facilities. Note that when a large holdover time is
expected or needed, a two-step procedure is recommended, using undiluted
fluid for the second step.
The one-step process
It is accomplished using a heated or in certain case an unheated FPD
mixture. In this process, the residual FPD fluid film provides a very limited
anti-icing protection. This protection can be enhanced by the use of cold fluids or by the use of techniques
to cool heated fluid during the de-icing process.
The two-step process
This process involves both de-icing and anti-icing procedure. First step (de-icing) is accomplished with hot
water or a hot mixture of FPD fluid and water. The ambient weather conditions and the type of accumulation
to be removed from the aircraft must be considered when determining which de-icing fluid to use. The second
step (anti-icing) involves application of type II or type IV fluid and water to the critical surfaces of the aircraft.
2.2. Equipment and material
De-icing or anti-icing procedures use the following products:
Hot air
Heated water
Type I de-icing fluids (in accordance with ISO, SAE or AEA standards).
Type II or type IV anti-icing fluid (in accordance with ISO, SAE or AEA
standards).
NOTE: The staff performing this operation must observe the safety precautions in force (gloves,
and safety goggles). If de-icing or anti-icing fluid is accidentally sprayed on skin, rinse thoroughly
with water to avoid irritation.
2.3. Fluid selection
The selection of de-icing process depends on numerous parameters. Therefore, only the experience of the
operator will direct the choice of the appropriate method according to the prevailing weather. The following
table provides basic information to determine the appropriate procedure to be used:
Note:
The second step anti-icing has to be applied before the first step freezes, typically within 3 minutes.
For heated fluid temperature not less than 60 C (140 F) at the nozzle is desired.
Warning
Aircraft must be de-iced/anti-iced symmetrically, so that
left-hand and right-hand side receive the same treatment,
whatever the status of the aircraft prior to the de-icing/anti-
icing procedure. Aerodynamics problems could result if this
requirement is not met.
Anti-icing procedure can only be performed on an aircraft
previously cleared of any contaminants (ice, snow, fluid resi-
dues...). If an additional treatment is required after previous
anti-icing, it is prohibited to perform new anti-icing without
having washed or de-iced the aircraft. If not, a dry film can
appear and may not be blown away by wind during taxing/
take-off.
OAT (Outside Air
Temperature)
One-step procedure
Two-step procedure
First step: de-icing Second step: anti-icing
Type I fluid (orange)
3 C (27 F)
and above
Freezing point of heated
fluid mixture shall be at
least 10 C (18 F) below
actual OAT.
Water heated to 60 C
(140 F) minimum at
the nozzle or a heated
mixture of fluid and water
Freezing point of heated fluid
mixture shall be at least 10 C
(18 F) below actual OAT.
Below 3 C (27 F) Freezing point of heated
fluid mixture shall not be
more than 3 C (5 F)
above actual OAT
Type II (translucent) or type IV (green) fluid
3 C (27 F)
and above
50/50 heated fluid/water
type II or type IV mixture
Water heated to 60 C
(140 F) minimum at
the nozzle or a heated
mixture of type I, II or IV
fluid and water
50/50 fluid/water type II or
type IV mixture
Below
3 C (27 F) to
14 C (7 F)
Heated 50/50 fluid/water
or suitable mixture of
type I with freezing point
not more than 3 C (5 F)
above actual OAT
type IV mixture
Below
14 C (7 F) to
25 C (13 F)
Heated 75/25 fluid/water
or suitable mixture of
type I with freezing point
not more than 3 C (5 F)
above actual OAT
type IV mixture
Below 25 C
(13 F)
Type II or IV fluid may be used below 25 C (13 F) provided that the freezing point
of the fluid is at least 7 C (14 F) below OAT and that aerodynamic acceptance
criteria are met. Consider the use of type I when type II or IV fluid cannot be used.
3. De-icing and anti-icing procedures
3.1. Aircraft preparation
ATR aircraft can be de-iced and anti-iced both at the parking area and at the holding point, engine running in hotel
mode, bleeds OFF. If a procedure is initiated at the parking area it is recommended to observe the following points:
Check that all doors and emergency exits are closed.
The aircraft shall be placed facing into the wind, engines not running.
Apply parking brakes and install wheel chocks.
Install blanking devices and protective equipment on the following components.
3
4 5 1 1 2
1 - Naca ports 4 - Pitot probes
2 - Air conditioning inlets of the main landing gear fairing 5 - Temperature sensors
3 - Static ports
CAUTION: Maintain the control column at full forward position during whole operation and engage gust lock.
3.2. Procedures
3.2.1. Snow removal
Before de-icing, ground staff has to sweep or blow off the snow layer.
Check that ground staff:
Pays attention to antennas, probes and vortex generators and avoids walking on no step areas.
Starts from the various hinge points to avoid snow accumulation.
Removes snow from engine air intakes, propeller blades, landing gears and brakes.
3.2.2. De-icing/anti-icing
Set platform to suitable height so that the ground staff is above the surface to be treated. The spray must
be applied at low angle (less than 45 degrees).
Warning
De-icing of the elevator must be successively performed from the under-
neath and the above of the surfaces with the elevator trailing edge in full
up and then full down position to better clean the leading edge.
Anti-icing (with thickened anti-icing fluid either neat or diluted) of
the elevator must be performed with the elevator trailing edge in full
down position to allow evacuation of excess anti-icing fluid. For more
details, refer to JIC 12-31-12.
On the various fairing and fillets, the de-icing or anti-icing fluid should
not be sprayed at pressure higher than 1.5 psi (0.103 bar). On the other
parts, the pressure of the sprayed fluid should not exceed the pressure recommended by the fluid manufacturer.
De-icing or anti-icing of the fuselage
Avoid as much as possible direct spraying on the windshields and windows.
Special precaution shall be taken to prevent fluid spraying onto the ADC probe and sensors (pitot probes,
statics sensors, TAT probes). Any contaminants entering these probe/sensors may lead to erroneous flight
parameters while in flight.
De-icing or anti-icing of airfoil and control surfaces
Start de-icing/anti-icing by filling the gap between fixed and movable surfaces in order to avoid accumulation
of contaminant, then proceed from the leading edge backward. caution: special care must be paid to the
gaps between:
Wings/ ailerons/ tabs
Horizontal stabilizer / elevators/ tabs
Rudder / vertical stabilizer / tab
These gaps must be clear of any contamination and must be checked after any de-icing or anti-icing procedure.
De-icing of landing gear
Prevent fluid contact with shock absorbers.
Avoid de-icing or anti-icing fluid entering brake unit.
Pay particular attention to proximity switches.
De-icing of propellers
Propeller covers should be used when possible. In order to avoid any de-icing fluid ingress in the engine
air intakes, no propeller blade should be in front of the air intake or the air intake cover should be installed.
In case of air intake de-icing fluid ingestion, the area must be wiped up. The fluid sprayed on the blades
shall not exceed 60C.
3.3. Hotel mode
Hotel mode is specific to ATR. It allows the aircraft to be de-iced while the right engine is running with the
propeller stopped and bleed air valve off. Thus the ATR could be de-iced and anti-iced like jet aircraft at the
holding point.
Air intake and wing snow removal, and propeller de-icing must be performed prior to hotel mode activation.
hotel mode de-icing/ anti-icing procedure can be conducted provided:
De-icing/ anti-icing gantry is not used,
Manual procedures are applied (with a de-icing nozzle from a movable platform) to avoid any inadvertent
entry of fluid into engines, naca ports, air conditioning inlets, static ports, pitot probes, temperature sensors,
and engine 2 bleed air valve off.
NOTE: The ground procedures to apply are entirely described in JIC 12-31-12 De-icing and/or anti-icing of the aircraft.
4. Fluid residues
Thickened de/anti-icing fluids (Type II or Type IV) can leave residue in aerodynamically quite areas. These
residues accumulate over time, can rehydrate, and form into a gellike substance and freeze during flight.
If located on critical surfaces or in areas of flight control components and linkages, handling characteristics
may be affected and control surface movement may be restricted.
Aircraft exposed to de/anti-icing fluids shall be subjected to periodic inspections for fluids residues, and any
residue found shall be removed.
Experience has shown that spraying water onto the concerned surface may help after few minutes in detecting
those residues while transforming into gel.
The following conditions are prone to residue formation:
Preventive application of type II or IV anti-icing fluids for overnight protection.
Successive application of type II or IV anti-icing fluids in one-step de/anti-icing procedures.
High temperature gradient on ground along a day (i.e. spring season)
It is recommended to prefer a two-step de-/anti-icing procedure where the first step using neat or diluted
type I fluid will clean the aircraft from any contaminants including thickened fluid residues.
Detailed periodic inspections of the critical surfaces are also recommended all along the winter season to detect any
residue formation. Inspection interval may be adapted according to the operator experience and the frequency
of exposure to type II or IV anti-icing fluids.
5. Captains decision
As the final decision rests with the Captain, his request will supersede the ground crew members judgement
to not de-ice.
As the Captain is responsible for the anti-icing condition of the aircraft during ground manoeuvering prior
to takeoff, he can request another anti-icing application with a different mixture ratio to have the aircraft protected
for a longer period against accumulation of precipitation. Equally, he can simply request a repeat application.
Therefore, the Captain should take into account forecasted or expected weather conditions, taxi conditions,
taxi times, holdover time and other relevant factors. The Captain must, when in doubt about the aerodynamic
cleanliness of the aircraft, perform an inspection or simply request a further de-/anti-icing.
Even when responsibilities are clearly defined and understood, sufficient communication between flight and
ground crews is necessary. Any observation considered valuable should be mentioned to the other party
to have redundancy in the process of decisionmaking.
6. Anti-icing codes
It is essential that the flight crew receives clear information from ground staff concerning the treatment applied
to the aircraft.
The AEA (Association of European Airlines) recommendations and the SAE and ISO specifications promote the
standardized use of a four-element code. This gives flight crew the minimum details to assess holdover times.
The use of local time is preferred but, in any case, statement of the reference is essential. These information
must be recorded and communicated to the flight crew by referring to the last step of the procedure.
Examples of anti-icing codes
AEA Type II/75/16.43 local TLS / 19 Dec 99
AEA Type II : Type of fluid used
75 : Percentage of fluid/water mixtures by volume, i.e. 75% fluid/ 25% water
16.43 : Local time of start of last application
19 Dec 99 : Date
ISO Type I/50:50/06.30 UTC/ 19 Dec 99
ISO Type I : Type of fluid used
50:50 : Percentage of fluid/water mixtures by volume, i.e. 50% fluid / 50% water
06.30 : Time (UTC) of start of last application
19 Dec 99 : Date
7. Holdover time
Holdover protection is achieved by anti-icing fluids remaining on aircraft surfaces and protecting them on ground for a
period of time.
With a one-step de/anti-icing operation, holdover begins at the start of the operation. With a two-step opera-
tion, holdover begins at the start of the second (anti-icing) step. Holdover time will have effectively run out,
when frozen deposits start to form/ accumulate on aircraft surfaces.
Due to its properties, Type I fluid forms a thin liquid-wetting film, which gives a rather limited holdover time,
depending on weather conditions. With this type of fluid, increasing the concentration of fluid in the fluid/water
mix would provide no additional holdover time.
Type II and Type IV fluids contain a thickener which enables the fluid to form a thicker liquid-wetting film on
external surfaces. This film provides a longer holdover time, especially in conditions of freezing precipitation.
With this type of fluid, additional holdover time will be provided by increasing the concentration of fluid in the
fluid/water mix, with maximum holdover time available from undiluted fluid.
All de/anti-icing fluids following the specifications mentioned below are approved for all ATR aircraft:
Type I: SAE AMS 1424 standard last effective issue
Type II: SAE AMS 1428 standard last effective issue
Type IV: SAE AMS 1428 standard last effective issue
Tables given below provide an indication of the protection timeframe that could reasonably be expected under
precipitation conditions.
NOTE: The protection times represented in these tables are for general information purposes only. They are taken from the AEA Recommendations
for de-icing / anti-icing of aircraft on ground, published by the Association of European Airlines, effective August 2010 and in accordance with
ISO/SAE specifications. However, local authority requirements may differ.
Due to the many variables that can influence holdover times, these times should not be considered as fixed,
since the actual time of protection may vary depending upon the particular conditions existing at the time.
The protection time will be shortened in severe weather conditions. Heavy precipitation rates or high mois-
ture content, high wind velocity and jet blast may cause a degradation of the protective film. If these condi-
tions occur, the protection time may be shortened considerably. This is also the case when the aircraft skin
temperature is significantly lower than the Outside Air Temperature.
The lower limit of the published time span is used to indicate the estimated time of protection during heavy
precipitation and the upper limit, the estimated time of protection during light precipitation.
IMPORTANT: The fluids used during ground de/anti-icing is not intended for and does not provide protection during the flight.
Before take-off, pilots must be aware of potential in-flight severe icing conditions (please refer to AFM 2.05 p6 for a description
of aloft severe icing weather conditions). If such conditions exist, take-off must be delayed.
7.1. Estimated holdover times for Type I fluid mixtures
The table below is an example of the holdover times anticipated for SAE Type I fluid mixtures, as a function
of weather conditions and OAT.
Example for training only
OAT
Approximate holdover times under various weather conditions
(hours: minutes)
C F Active frost Freezing fog
Snow , snow
pellets, snow
grains
Freezing
drizzle
(1)

Light freezing
rain
Rain on cold
soaked wing
3 and above 27 and above 0:35 0:09-0:16 0:03-0:06 0:08-0:13 0:02-0:05 0:01-0:05
3 to 6 27 to 21 0:35 0:06-0:08 0:02-0:05 0:05-0:09 0:02-0:05
CAUTION:
Clear ice may
require touch
for confirmation
7 to 10 20 to 14 0:35 0:04-0:08 0:02-0:05 0:04-0:07 0:02-0:05
Below 10 Below 14 0:35 0:04-0:07 0:02-0:04
C: Degrees Celsius - F: Degrees Fahrenheit - OAT: Outside Air Temperature
(1) Use light freezing rain holdover times if positive identification of freezing drizzle is not possible.
SAE Type I fluid/water mixture is selected so that the freezing point of the mixture is at least 10 C (18 F) below OAT.
7.2. Estimated holdover times for Type II fluid mixtures
The table below is an example of the holdover times anticipated for SAE Type II fluid mixtures, as a function
OAT
SAE Type II
fluid
concentration
(hours: minutes)
C F
Neat-fluid /
water (Vol. %
/ Vol. %)
Active
frost
Freezing
fog
Snow , snow
pellets,
snow grains
Freezing
drizzle
(2)

Light
freezing rain
Rain
on cold
soaked
wing
Others
(3)

Above 3 Above 27
100/0 8:00 0:35-1:30 0:20-0:45 0:30-0:55 0:15-0:30 CAUTION:
Clear ice
may
require
touch for
confirma-
tion
CAUTION:
No
holdover
time
guidelines
exist
75/25 5:00 0:25-1:00 0:15-0:30 0:20-0:45 0:10-0:25
50/50 1:30-3:00 0:15-0:30 0:05-0:15 0:05-0:15 0:05-0:10
3 to 14 27 to 7
100/0 6:00-8:00 0:20-1:05 0:15-0:30 0:20-0:45
(1)
0:10-0:20
(1)

75/25 1:00-5:00 0:25-0:50 0:10-0:20 0:15-0:30
(1)
0:05-0:15
(1)

14 to 25
and below
(4)
7 to 13 100/0 2:00-6:00 0:15-0:35 0:15-0:30
C: Degrees Celsius - F: Degrees Fahrenheit - OAT: Outside Air Temperature - Vol: Volume
(1) No holdover time guidelines exist for this condition below 10 C (14 F)
(2) Use light freezing rain holdover times if positive identification of freezing drizzle is not possible
(3) Heavy snow, ice pellets, moderate and heavy freezing rain, hail
(4) SAE Type II fluid may be used below 25 C (13 F) provided the freezing point of the fluid is at least 7 C (13 F)
below the OAT and the aerodynamic acceptance criteria are met. Consider use of SAE Type I when SAE Type II
fluid cannot be used.
7.3. Estimated holdover times for Type IV fluid mixtures
The table below is an example of the holdover times anticipated for SAE Type IV fluid mixtures, as a function
OAT
SAE Type IV
fluid
concentration
(hours: minutes)
C F
Neat-fluid /
water (Vol. %
/ Vol. %)
Active
frost
Freezing
fog
Snow , snow
pellets, snow
grains
Freezing
drizzle
(1)

Light
freezing rain
Rain on cold
soaked wing
Others
(3)
Above 3 Above 27
100/0 12:00 1:15-2:30 0:35-1:15 0:40-1:10 0:25-0:40
CAUTION:
Clear ice
may require
touch for
confirmation
CAUTION:
No holdover
time
guidelines
exist
75/25 5:00 1:00-1:45 0:20-0:55 0:35-0:50 0:15-0:30
50/50 3:00 0:15-0:35 0:05-0:15 0:10-0:20 0:05-0:10
3 to 14 27 to 7
100/0 6:00-10:00 0:20-1:20 0:20-0:40 0:20-0:45
(2)
0:10-0:25
(2)

75/25 1:00-5:00 0:25-0:50 0:15-0:35 0:15-0:30
(2)
0:10-0:20
(2)

14 to 25
or below
(4)

7 to 13
or below
(4)

100/0 4:00-6:00 0:15-0:40 0:15-0:30
C: Degrees Celsius - F: Degrees Fahrenheit - OAT: Outside Air Temperature - Vol: Volume
(1) Use light freezing rain holdover times if positive identification of freezing drizzle is not possible
(2) No holdover time guidelines exist for this condition below 10 C (14 F)
(3) Heavy snow, ice pellets, moderate and heavy freezing rain, hail
(4) SAE Type IV fluid may be used below 25 C (13 F) provided the freezing point of the fluid is at least 7 C
(13 F) below the OAT and the aerodynamic acceptance criteria are met. Consider use of SAE Type I when SAE
Type IV fluid cannot be used.
D. Aircraft ice
protection systems
D. Aircraft ice protection systems 29
1. Systems description
On a turboprop aircraft the ancillary power available (bleed air and electrical power) is less than on a jet.
Consequently a permanent thermal protection is impracticable, in particular for the airframe. A solution consists in
installing a pneumatic de-icing system on the exposed critical parts (i.e airframe) complemented by an electrical
anti-icing protection for the parts on which a pneumatic de-icing device is not applicable, i.e rotating components
(such as propellers), windshields, probes. This philosophy is applied on all new generation turboprop airplanes.
On ATR aircraft, ice protection is generally provided by the system, as illustrated on the figure below.
NOTE: To review the specific system installed on your aircraft, refer to your FCOM.
Pneumatic
de-icing
Wing leading
edges
Horizontal tailplane
leading edge
Engine air
intakes
Gas path
de-icer
Windshields Probes
Electrical
anti-icing
Propellers Horns
Ice evidence
probe
Electronic ice
detector
Example of ATR 72-500 basic ice protection system
1.1. Electrical System
The electrical heating power is supplied by AC wild frequency power.
Permanent level
Probes and windshield (always selected ON),
Anti-icing
Side windows (heating for defogging only, not for ice
protection),
Flight control horns (ailerons, elevators, rudder),
Inner leading edge of propeller blades (outer part is
de-iced by centrifugal force only).
Propeller ice protection system combines electrical
heating of blades leading edge and centrifugal
force. Heating cycle duration have been optimized
according to OAT to decrease the adhesion strength
of the accreted ice. Ice is then shed by the centrif-
ugal effect.
SAT > 10C
SAT < 10C
0 10 20 30 40 50 SECONDS
80 SECONDS 60 40 20 0
PROPELLER 1
PROPELLER 1 PROPELLER 1 PROPELLER 2 PROPELLER 2
PROPELLER 2
BLADES 1-3-5 BLADES 2-4-6 BLADES 1-3-5 BLADES 2-4-6
BLADES
2-4-6
BLADES
1-3-5
BLADES
2-4-6
BLADES
1-3-5
Electrical ice protection sequence Example of sequencing
applicable to ATR 72-500.
D. Aircraft ice protection systems
1.2. Pneumatic System
Pneumatic System (de-icing) supplying the de-icing for
the critical areas of the airframe:
Wing and horizontal tailplane leading edges,
Engine air intakes and engine gas paths
1
.
The pneumatic boot de-icers are constituted by dual
chambers (chordwise chambers on the airframe) which
alternatively inflate. The de-icing cycle duration has
been determined by tests to provide optimized de-icing
performance according to the outside air temperature.
Two cycles are available: 1 mn for cool temperature
and 3 mn for cold temperature. On ATR-500 aircraft
the cycles are automatically set.
1.3. Aircraft Performance Monitoring
Some Aviation Investigation Authorities have recommended to all aircraft manufacturers developing an onboard
detector to warn the crew when the aircraft is in severe icing conditions. Recent recommendations also ask
for the installation of low speed warning devices.
In response to the Authority recommendations, ATR has developed the Aircraft Performance Monitoring (APM) to
contribute to the safety of flights and to deal with severe icing conditions. This function is included into the MPC
(Multi Purpose Computer) and does not need additional sensors or any calculation of atmospheric ice content. The
APM calculates, during the flight, the airplane actual performance and compares them with the expected ones. It
also computes the actual minimum icing and severe icing speeds for the given flight condition.
2. Systems operation
2.1. Ice accretion monitoring
Ice accretion may be detected primarily by observing the Ice Evidence Probe (IEP). At night, the IEP is automati-
cally illuminated when NAV lights are turned ON. Ice accretion may also be detected on windshield, airframe
(leading edges), wipers, side windows and propeller spinners (visible from cockpit on ATR 42).
The IEP allows monitoring ice accretion and is designed to retain ice on its surface until the whole aircraft is free
of ice. On the ATR 42 without IEP, this role is ensured by the propeller spinner. In addition to the primary means
of recognising ice accretion mentioned above, an anti icing advisory system (AAS) is installed on ATR aircraft.
It includes:
An electronic ice detector
Three lights in the cockpit on the central panel between the two pilots: ICING (amber), ICING AOA (green),
DE ICING (blue).
This system is not a primary system but has been designed to alert the crew to implement the correct proce-
dures when flying in icing conditions (see Procedures). The electronic ice detector is located under the left
wing and alerts the crew as soon as and as long as ice accretion develops on the probe. Aural and visual
alerts are generated (Amber ICING light on the central panel and single chime).
ENGINE AIR
INTAKES

FOR SAT
FOR SAT
> -20C = 1mn
< -20C = 3mn
ATR 72
BOOTS
A
ENG. 1
BOOTS
B
ENG. 1
BOOTS
A
BOOTS
B
BOOTS
B
BOOTS
B
BOOTS
A
BOOTS
A
BOOTS
A
ENG. 2
BOOTS
B
ENG. 2
COMPUTER
1
COMPUTER
2
EXTERNAL
WING
MEDIAN
WING
HORIZONTAL
STABILIZER
BASIC VERSION
CYCLES
0 5 10 15 20 25 30 35 40 45 50 60 180
SECONDS
INFLATION
DEFLATION
Pneumatic de-icing system Example of sequencing applicable
to ATR 72-500.
1: Certain local regulations require that the engine de-icing system be activated whenever the anti-icing system is engaged.
ICING (amber - ice detector light)
ICING flashes amber when ice accretion is detected and horns anti-icing and/or airframe de-icing are not
selected ON (associated with a single chime if horns anti-icing and airframe de-icing are not selected ON). The
crew has forgotten to select both ice protection systems. Icing light is flashing until the airframe pushbutton
is selected ON. ICING illuminates steady amber when ice accretion is detected provided both horns anti-icing
and airframe de-icing are selected ON.
NOTE: To verify that the electronic ice detection is functionning properly, press the ice detector test push button.
ICING AOA (green - push button)
Illuminates green as soon as one of the horn anti-icing push buttons is selected ON, reminding the crew that
the stall warning AOA threshold is lower in icing conditions. The lower stall warning AOA threshold defined
for icing is active.
The ICING AOA green light can only be extinguished manually by depressing it, provided both horns anti-icing buttons
are selected OFF. This should be done after the pilots have confirmed that aircraft is clear of ice. In this case the
stall warning AOA threshold recovers the values defined for flight in normal conditions.
CONT
RELIGHT
FUEL
X FEED
PROP
BRK
SEAT
BELTS
NO
SMKG
FAULT
ICING
ICING
AOA
P
T
T
DE-
ICING
CRUISE
SPEED LOW
INCREASE
SPEED
DEGRADED
PERF.
(test
button)
ATR 72-500 cockpit view
D. Aircraft ice protection systems
DE-ICING (blue)
Illuminates blue when the airframe deicing system is selected ON.
Flashes blue when the airframe de-icing system is still selected ON five minutes after the last ice accretion
detection.
2.2. Enhanced Ice accretion monitoring with the APM
Icing drastically decreases the aircraft performance: an abnormal increase in drag can be due to ice accretion
on the aerodynamical surfaces of the aircraft. Monitoring the aircraft performance is thus an efficient means
of ice detection, in addition to the common means detailed above.
The APM enables to compare the aircraft theoretical drag with the in-flight drag computed with the meas-
ured parameters, and therefore to detect if an abnormal loss of aircraft performance occurs. The APM is
activated in icing conditions, i.e. when ICING AOA is illuminated, or if the airframe de-icing is activated, or if
ice accretion has been detected, and aims at alerting the crew of a risk of severe icing conditions, through
three different levels of signal:
Cruise speed low
Degraded Performance
Increase speed
CRUISE SPEED LOW (blue)
The speed in cruise is monitored and if an abnormal increase in drag induces an abnormal speed decrease
of more than 10kts compared to the expected one, this message lights on.
DEGRADED PERF. (amber)
In cruise or in climb, if an abnormal drag increase induces a speed decrease or a loss of rate of climb, this
alert is triggered in association with a single chime and a master CAUTION on the attention getter. In cruise,
this occurs right after the CRUISE LOW SPEED.
INCREASE SPEED (amber)
In cruise, climb or descent, if the drag is abnormally high and that IAS is lower than the MSIS (Minimum
Severe Icing Speed equivalent to red bug + 10 kts), this message flashes in association with a single chime
and a master CAUTION on the attention getter. This occurs right after the DEGRADED PERF.
E. Performance
E. Performance 34
E. Performance 35
E. Performance
1. Impact of contamination by ice or snow
As the aircrafts external shapes are carefully optimized from an aerodynamic point of view, it is no wonder
that any deviation from the original lines due to ice accretion leads to an overall degradation of performance
and handling, whatever the type. The real surprise comes from the amount of degradation actually involved
and the lack of a logical relationship with the type of accretion.
Comprehensive wind tunnel tests have been carried out by various institutes and manufacturers over the past
several decades, providing a wealth of results that have been largely confirmed by flight tests on different
types of jets and turboprops.
The main effects of ice accretion can be summarised as follows.
NOTE: These conditions are certification cases, and not severe ice cases. Severe icing may thus lead to more detrimental effects.
1.1. Lift
The lift curves are substantially modified compared to clean aircraft;
Reduction of lift at a given angle of attack,
Reduction of maximum lift,
Reduction of maximum lift angle of attack.
When the maximum lift capability of the wing decreases by 25%, the actual
stall speed is 12% higher than the basic stall speed (clean aircraft).
Consequently an iced aircraft flying at a given speed (and thus at a
given CL) will have a reduced stall margin either looking at angle of
attack (6.5 less margin) or looking at stall speed (12% less margin).
More surprising is the fact evidenced by fig. 4: the bulk of maximum
lift degradation is already present with accretions as small as a few
millimeters.
A CLmax decrease of 0.5 typically means a stall speed increase of
10kt for an ATR 42 with flaps 15. The ATR 42 wind tunnel test results
with single or double horn shapes are consistent with the curves
derived from extensive tests carried out on conventional airfoils by the
Swedish - Soviet working group on flight safety.
1.2. Drag
The drag polar is also heavily affected (fig. 5)
Greater drag at a given angle of attack,
Greater drag at a given lift,
Best lift/drag ratio at a lower lift coefficient.
Arg|e ol Allac|
Coell|c|erl ol L|ll
C|ear
lced
CLrax = -25
- .5
Effect of certified ice shapes on
lift curve Flaps 30, gear down
standard de-icers
AvERA0E lCE
TllCKNE33 (|r) 0 1 2 3
wlN0
0
-0.5
- 1
CLrax
wlN0
30uRCE: 3Wed|sr - 3ov|el Wor||rg group - F||grl 3alely - lr Veel|rg - 19ZZ
ATR 12 resu|ls - F|aps 15
Effect of ice shape on CLmax Wind
tunnel tests Flaps 15
Coell|c|erl ol 0rag
Coell|c|erl ol L|ll
C|ear
lced
ATR 72 Effect of certified ice
shapes on drag polar Flaps 0
Standard de-icers
E. Performance 36
1.3. Performance
The drag and lift penalties described in the chapter Weather Revision give a good idea of the performance
impacts that could be expected from ice accretion. Beyond the main phenomenon, other effects should not
be underestimated: for example, ice accretion on propeller blades will reduce the efficiency and the avail-
able thrust of propeller driven aircraft, ice accretion in the engine air intakes may cause engine flame out.
Evidence has shown that unusual accretion patterns located further aft the leading edge, can have an even
more adverse effect on performance. On the other hand, ice weight effect will remain marginal when compared
to other penalties.
1.4. Handling
In order to ensure a satisfactory behaviour, aircraft are carefully designed so that stall will occur initially at the
inner portion of the wing and spread toward the tip as angle of attack increases. Roll moments and abrupt-
ness of lift drop are then minimised.
This stall behaviour can be completely jeopardized by ice accretions that have no particular reason to be
symmetrical or regular along the entire span of the wing.
Other potentially hazardous effects are also linked to tail surface icing: reduced maximum lift and stall angle
of attack may result in tail surface stall under conditions where, if clean, it would properly do its job.
These conditions are those of high negative angle of attack and downloads on the tail surfaces, encountered
for extreme manuvers at high flap settings.
Separated airflow on the tail surface can also seriously affect elevator behaviour when manually actuated, as
aerodynamic compensation of control surfaces is a fine tuned and delicate technique.
Similar anomalies can affect other unpowered controls (such as ailerons) when ice accretion exists.
ATR in particular has documented the effects on aileron behaviour of unusual ice shapes associated to freezing drizzle.
2. Documentation provided by ATR
ATR provides data to compute flight plans in icing conditions. This data can be found under the label Icing
Conditions for the following sections:
Climb: FCOM section 3.04
Cruise: FCOM section 3.05
Holding: FCOM section 3.06
Descent: FCOM section 3.07
One engine inoperative 3.09
All performance data given for icing conditions derive from flight tests measurements performed with ice shapes
representative of the worst icing cases considered by certification and applicable losses of propeller efficiency.
Because of the variability of real icing, climb performance published for icing conditions must be regarded
with the utmost care. Always compare actual performances to predicted ones.
Note that FOS, the ATR flight operations software, is able to compute a complete flight in icing conditions.
E. Performance
E. Performance 37
Example of a FOS flight planning log computed in icing conditions
3. Performance on contaminated runways
Operations on fluid contaminated runways raise numerous questions
from operators. Airlines which often operate under cold or inclement
conditions are generally concerned in obtaining a better understanding
of the numerous factors influencing aircraft braking performance: on
one hand, how to minimize the payload loss, and on the other, how
to maintain a high level of safety.
It is evident that the braking performance is strongly affected by a slip-
pery runway, however, one should also consider the loss in acceleration
performance and in aircraft lateral controllability.
Once the performance impact of a contaminated runway is explained,
it is quite necessary to review the operational information provided to
the pilots. This information mainly contains some penalties (e.g. weight
penalty or maximum crosswind reduction) but as well some indications
on the runway condition provided as a friction coefficient.
All this information should be readily understood so as to jeopardize
neither airline safety nor airline economics.
LFBO/LFBD 19/09/2003 PREPARED BY : ......
FLT NBR ...... CPT ......... F/O ......... INST .........
UNITS: KG/NM/FT/KT CAB ATTN ......... CAB ATTN .........
--------------------------------------------------------------------------------
LFBO TOC WPT1 WPT2 WPT3 TOD LFBD
--------------------------------------------------------------------------------
AIRCRAFT FL SPEED PAX:... BAGGAGE CARGO = PAYLOAD
42-300 42-300 50 CLIMB/DESC. ....... ....... ....... = .......
MAX CRUISE 160KT/220KT
FUEL FACTOR = 1.00 AIR COND. = NORMAL ISA ATMOSPHERIC COND. = ICING
--------------------------------------------------------------------------------
E.FUEL A.FUEL E.TIME NM FL WIND
DESTI LFBD 262 ...... 00:24 79 50 0 KT TAIL
+ ALTERNAT 0 ...... 00:00
+ RESERVE 5% F 200 ...... 00:17
+ FINAL RESERVE 316 ...... 00:45
+ ADDITIONAL FUEL 500 ...... 00:43
-----------------------
= MIN T/O FUEL 1278 ...... 2:09
+ HOTEL 0 ...... 00:00
+ TAXI 14 ...... 00:03
+ EXTRA FUEL ...... ...... ..:..
-----------------------
= MIN BLOCK FUEL 1292 ...... ..:.. CAPT.SIGN . . . . . . . .
--------------------------------------------------------------------------------
E.WT A.WT WT LIMIT: | FUEL MANAGEMENT
OEW 10000 ...... | E.FUEL A.FUEL
+ PAYLOAD 5384 ...... | ALTERN 0 ......
= ZFW 15384 ...... MZFW = 15540 |+ FINAL RESERV 316 ......
+ MIN T/O FUEL 1278 ...... |= MIN ALTERNAT 316 ......
= TOW 16662 ...... RTOW = ..... | FOB AT DESTI ...... ......
- TRIP FUEL 262 ...... |- MIN ALTERNAT 316 ......
= LW 16400 ...... RLW = ..... |= DEST HOLDING ...... ......
| E.TIME ..:..
--------------------------------------------------------------------------------
SCHED. BLOCK FLIGHT DELAY CONTRACTOR . . . . BLOCK FUEL . . . .
DEP ..:.. ..:.. ..:.. ..:.. LITERS . . . . RFOB . . . .
ARR ..:.. ..:.. ..:.. CODE FUEL Q . . . . FUEL BURNT . . . .
TIME ..:.. ..:.. ..:.. .... REMAINING Q . . . .
--------------------------------------------------------------------------------
E. Performance 38
3.1. What is a contaminated runway?
A runway is considered contaminated when more
than 25% of the surface is covered with a contami-
nant. Contaminants are water, slush, snow and ice.
3.2. Braking means
There are two ways of decelerating an aircraft:
The primary way is with the wheel brakes. Wheel brakes stopping performance depends on the load
applied on the wheels and on the slip ratio. The efficiency of the brakes can be improved by increasing
the load on the wheels and by maintaining the slip ratio at its optimum (anti-skid system).
Secondly, reverse thrust decelerates the aircraft by creating a force opposite to the aircraft motion regard-
less of the runway condition. The use of reverse thrust is indispensable on contaminated runways.
3.3. Braking performance
The presence of contaminants on the runway affects the performance by:
1. A reduction of the friction forces () between the tire and the runway surface,
2. An additional drag due to contaminant spray impingement and contaminant displacement drag,
3. Aquaplaning (hydroplaning) phenomenon.
There is a clear distinction between the effect of fluid contaminants and hard contaminants:
Hard contaminants (compacted snow and ice) reduce the friction forces.
Fluid contaminants (water, slush, and loose snow) reduce the friction forces, create an additional drag
and may lead to aquaplaning.
Definitions (extract from FCOM 3.03.01) or below.
Damp
A runway is damp when the surface is not dry, but when the water on it does not
give it a shiny appearance.
Wet
A runway is considered as wet when the surface has a shiny appearance due to
a thin layer of water. When this layer does not exceed 3 mm depth, there is no
substantial risk of hydroplaning.
Standing water
Is caused by heavy rainfall and/or insufficient runway drainage with a depth of more
than 3 mm.
Slush
Is water saturated with snow, which spatters when stepping firmly on it.
It is encountered at temperature around 5C and its density is approximately
0.85 kg/liter (7.1 lb/US GAL).
Wet snow
Is a condition where, if compacted by hand, snow will stick together and tend to
form a snowball. Its density is approximately 0.4 kg/liter (3.35 lb/US GAL).
Dry snow
Is a condition where snow can be blown if loose, or if compacted by hand, will fall
apart again upon release. Its density is approximately 0.2 kg/liter (1.7 lb/US GAL).
Compacted snow Is a condition where snow has been compressed (a typical friction coefficient is 0.2).
Icy Is a condition where the friction coefficient is 0.05
E. Performance
E. Performance 39
To develop a model of the reduced according to the type of contaminant is a difficult issue. Until recently,
regulations stated that wet and cont can be derived from the observed on a dry runway (dry/2 for
wet runway, dry/4 for water and slush).
Nevertheless, recent studies and test shave improved the model of for wet and contaminated runways,
which are no longer derived from dry. The certification of the most recent aircraft already incorporates
these improvements.
3.4. Correlation between reported and braking performance
Airports release a friction coefficient derived from a measuring vehicle. This friction coefficient is termed as
reported .
The actual friction coefficient, termed as effective is the result of the interaction tire/runway and depends
on the tire pressure, tire wear, aircraft speed, aircraft weight and anti-skid system efficiency.
To date, there is no way to establish a clear correlation between the reported and the effective
. There is even a poor correlation between the reported of the different measuring vehicles.
It is then very difficult to link the published performance on a contaminated runway to a reported only.
The presence of fluid contaminants (water, slush and loose snow) on the runway surface reduces the
friction coefficient, may lead to aquaplaning (also called hydroplaning) and creates an additional drag.
This additional drag is due to the precipitation of the contaminant onto the landing gear and the airframe,
and to the displacement of the fluid from the path of the tire. Consequently, braking and accelerating
performance are affected. The impact on the accelerating performance leads to a limitation in the depth
of the contaminant for takeoff.
Hard contaminants (compacted snow and ice) only affect the braking performance of the aircraft by a
reduction of the friction coefficient.
ATR publishes takeoff and landing performance according to the type of contaminant, and to the depth
of fluid contaminants.
3.5. Aircraft directional control
When the wheel is yawed, a side-friction force appears. The total friction force is then divided into the
braking force (component opposite to the aircraft motion) and the cornering force (side-friction).
The maximum cornering force (i.e. directional control) is obtained when the braking force is nil, while a
maximum braking force means no cornering.
The sharing between cornering and braking is dependent on the slip ratio, that is, on the efficiency of the
anti-skid system.
Cornering capability is usually not a problem on a dry runway, nevertheless when the total friction force is
significantly reduced by the presence of a contaminant on the runway, in crosswind conditions, the pilot
may have to choose between braking or controlling the aircraft.
4. Aircraft braking means
Aircraft braking performance, in other words, aircraft stopping capability, depends on many parameters.
Three means allow aircraft to decelerate: wheel brakes, aerodynamic drag, and reverse thrust.
4.1. Wheel brakes
Brakes are the primary means to stop an aircraft, particularly on a dry runway.
Deceleration is obtained by friction forces between runway and tires. Forces appear at the contact zone tire/
runway. By applying brakes, wheels are slowed down. This creates a force opposed to aircraft motion, which
depends on wheel speed and load applied on the wheel.
E. Performance 40
4.1.1. Wheel load
A load must be placed on the wheel to increase contact
surface between tire and runway, and to create a braking/
friction force.
There is no optimum on the load to be placed on wheels.
The greater the load, the higher the friction, the better the
braking action.
The friction coefficient is defined as the ratio between
maximum available tire friction force and vertical load acting
on a tire. This coefficient is named MU or .
4.1.2. Wheel speed
The area of tire/runway contact has its own speed, which can vary between two extremes:
Free rolling speed, which is equal to aircraft speed.
Lock-up speed, which is zero.
Any intermediate speed causes the tire to slip over
runway surface with a speed equal to: Aircraft speed
Speed of tire at the contact point. The slipping is
often expressed in terms of percentage to aircraft
speed.
Friction force depends on the slipping percentage.
It is easily understood that a free-rolling wheel (in
other words, 0% slip) does not resist to aircraft
motion, therefore does not create a friction force.
So, in theory, there is no braking action.
It is a well-known fact that a locked-up wheel
simply skidding over the runway has a bad braking
performance. Hence, the advent of so-called anti-
skid systems on modern aircraft.
Somewhere in between these two extremes lies the
best braking performance.
The following figure shows that the maximum friction
force, leading to the maximum braking performance,
is obtained for a slip ratio around 12%.
Tests have demonstrated that the friction force on a
dry runway varies with the aircraft speed as shown
on the following graph:
4.2. Reverse thrust
Reverse thrust creates a force opposite to aircraft motion, inducing a significant decelerating force, which is
independent of runway contaminant.
According to JAR 25.109, regulations do not allow a credit for the effect of reverse performance on a dry
runway.
However, regulations presently allow crediting reverses effect on takeoff performance for wet and contami-
nated runways.
The situation is a bit different for landing performance where regulations allow crediting effect of reverse only
for contaminated runways, and not for dry and wet runways.
PRINCIPLE OF ANTI-SKID SYSTEM
Extracted from FCOM, 1.14
The system compares the speed of each main gear
wheel (given by a tachometer) to a velocity reference
signal. The anti skid system applies a deceleration
law continuously adapting the actual wheel speed to
the reference speed.
Lookod Wnool
SLP-PATO PEPCENTAGE
Froo rotation
12%
F
P
C
T
O
N
F
O
P
C
E
Speed
APCPAFT MOTON
Friotion oroo
Friotion oroo
m =
Load
LOAO = % o airorat gross woignt on ono tiro.
E. Performance
E. Performance 41
Remark: This may lead to a performance-limited weight on a wet or contaminated runway being greater than
the performance-limited weight on a dry runway. It is compulsory to restrict the performance-limited weight
on a wet/contaminated runway to that of the corresponding dry runway.
As illustrated by the following graphs, reverse proportionally have a more significant effect on contaminated
runways than on dry runways, since only low deceleration rates can be achieved on contaminated or slippery
runways.
The results are computed with the following data:
ATR 42-300
MLW: 16.4 Tons
Flaps 30
Repartition of braking action between available means
10% 20% 70%
15% 30% 55%
26% 35% 39%
20% 36% 44%
45% 39% 16%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
% of braking action
Dry
Wet
Water
(1/4 inch)
Compacted
snow
Icy
T
y
p
e

o
f

c
o
n
t
a
m
i
n
a
n
t
Aerodynamic drag Reverse Wheel brake
5. Braking performance
5.1. Influence of the contaminants
Presence of contaminants on the runway surface affects braking performance in various ways.
The first obvious consequence of the presence of contaminants between tire and runway surface is a loss of
friction force, hence a reduced . If this phenomenon is quite natural to understand, it is difficult to convert
to useable figures. That is why the mathematical model is still evolving and is monitored by regulations.
Presence of a fluid contaminant like water or slush can also lead to a phenomenon known as aquaplaning
or hydroplaning. In such a configuration, there is a loss of contact, therefore a loss of friction, between tire
and runway surface.
Fluid contaminants produce a lot of precipitation on airframe and landing gears, causing additional drag.
Hard contaminants: Compacted Fluid contaminants: Water, slush and loose snow
snow and ice Decrease of friction forces + precipitation drag +
Decrease of friction forces aquaplaning
E. Performance 42
5.2. Reduction of the friction coefficient
Friction force reduction is due to interaction of the contaminant between tire and runway surface. One can
easily understand that this reduction depends directly on the contaminant. Let us review the reduction by
contaminant.
5.2.1. Wet runway
The following text is extracted from the ICAO Airport Services Manual, Part 2.
Normal wet friction is the condition where, due to the presence of water on a runway, the available friction
coefficient is reduced below that available on the runway when it is dry. This is because water cannot be
completely squeezed out from between the tire and the runway and, as a result, there is only partial contact
with the runway by the tire. There is consequently a marked reduction in the force opposing the relative
motion of the tire and runway because the remainder of the contacts is between tire and water.
To obtain a high coefficient of friction on a wet or water-covered runway, it is, therefore, necessary for the
intervening water film to be displaced or broken through during the time each element of tire and runway are
in contact. As the speed rises, the time of contact is reduced and there is less time for the process to be
completed; thus, friction coefficient on wet surfaces tend to fall as the speed is raised, i.e. the conditions in
effect become more slippery.
In other words, we expect
wet
to be less than
dry
, and to decrease as speed increases.
Until recently, regulations stated that a good representation of the surface of a wet runway condition is obtained
when considering
dry
divided by two.
As of today, a new method has been developed taking into account:
Level of tire wear
Type of runway
Tire inflation pressure
Anti-skid effect demonstrated through flight tests on wet runways.
In any cases, the braking friction coefficient decreases (non-linearly) with aircraft ground speed.
5.2.2. Fluid contaminated runway: water, slush and loose snow
The reason for friction force reduction on a runway contaminated by water or slush is similar to the one on a
wet runway. Loss in friction is due to the presence of a contaminant film between runway and tire resulting
in a reduced area of tire/runway dry contact.
As for the
wet
, cont is often derived from
dry
. Again, until recently, regulations stated that
cont
=
fry
/4.
As for wet condition, a new model has been developed to take into account state of tire wear, type of runway,
tire inflation pressure and anti-skid effect.
5.2.3. Hard contaminated runway: compacted snow and ice
These two types of contaminants differ from water and slush, as they are hard. Wheels just roll over them,
as they do on a dry runway surface but with reduced friction forces.
As no rolling resistance or precipitant drag is involved, the amount of contaminant on the runway surface is
of no consequence. Assuming an extreme and non-operational situation, it would be possible to takeoff from
a runway covered with a high layer of hard compacted snow, while it would not be possible to takeoff from
a runway covered with 10 inch of slush. One can easily imagine that rolling resistance and precipitation drag
would be too important.
The model of friction forces on a runway covered by compacted snow and icy runway as defined in the FCOM
section 2.02, leads to the following :
Compacted snow: = 0.35 to 0.30
Icy runway: = 0.25 and below
E. Performance
E. Performance 43
5.3. Precipitation drag
Regulation requires, in AMJ 25.1591:
During take-off acceleration, account should be taken of
precipitation drag. During accelerate-stop deceleration and
at landing, credit may be taken for precipitation drag.
Displacement drag
Drag produced by the displacement of contaminant fluid
from tire path, and increases with speed up to a value close
to aquaplaning speed.
It is proportional to the density of contaminant, to the frontal
area of the tire in the contaminant and to the geometry of
the landing gear.
Drag displacement = 0.5 S
tire
GS
2
C
D
K
is the density of the contaminant
S
tire
is the frontal area of tire in the contaminant
GS is the ground speed
C
D
is the coefficient equal to 0.75 for water or slush
K is the coefficient for wheels

GROUND SPEED
Aquaplaning speed
D
I
S
P
L
A
C
E
M
E
N
T
D
R
A
G
Spray impingement drag
Additional drag produced by the spray thrown up by wheels (mainly those of nose gear) onto fuselage.
5.4. Aquaplaning
As previously explained, presence of water on the runway creates an intervening water film between tire and
runway leading to a reduction of the dry area. This phenomenon gets more critical at higher speeds, where
water cannot be squeezed out from the interface between tire and runway. Aquaplaning is a situation where
the tires of the aircraft are, to a large extent, separated from the runway surface by a thin fluid film. Under
these conditions, tire traction drops to almost negligible values and aircraft wheels braking as well as wheel
steering for directional control is, therefore, virtually ineffective. ICAO Airport Services Manual, Part 2.
Aquaplaning speed depends on tire pressure and on the specific gravity of the contaminant (i.e. How dense
is the contaminant).
In other words, aquaplaning speed is a threshold from which friction forces decrease dramatically.
6. Correlation between reported and
braking performance
6.1. Information provided by airport authorities
Airport authorities give measurements of a runway friction coefficient. Results are published via a standard form,
called SNOWTAM, defined in ICAO Annex 15 Aeronautical Information Services.
E. Performance 44
A SNOWTAM contains:
The type of contaminant,
Mean depth for each third of total runway length,
Estimated braking action,
Reported .
E. Performance
E. Performance 45
The following table relates reported to estimated braking action and equivalent runway status.
Equivalent runway status:
1: Dry runway 5: Slush or water for depths between 3 and 13 mm
2: Wet up to 3 mm depth 6: Compact snow
3: Slush or water for depths between 3 and 6 mm 7: Ion
4: Slush or water for depths between 6 and 13 mm 8: Runway with high risk of hydroplaning
6.2. Difficulties in assessing the effective
The two major problems introduced by airport authorities evaluation of runway characteristics are:
Correlation between test devices, even though some correlation charts have been established.
Correlation between measurements made with test devices or friction measuring vehicles and aircraft
performance.
These measurements are made with a great variety of measuring vehicles, such as: Skidometer, Saab Friction Tester
(SFT), MU-Meter, James Brake Decelerometer (JDB), Tapley meter, Diagonal Braked Vehicle (DBV).
Refer to ICAO, Airport Services Manual, Part 2 for further information on these measuring vehicles.
The main difficulty in assessing braking action on a contaminated runway is that it does not depend solely
on runway surface adherence characteristics.
What must be found is the resulting loss of friction due to interaction between tire and runway. Moreover, the
resulting friction forces depend on the load, i.e. aircraft weight, tire wear, tire pressure and anti-skid system
efficiency.
In other words, to get a good assessment of the braking action of an ATR 72 landing at 15,000 kg, 95 kt
with tire pressure 144 PSI, the airport should use a similar spare ATR 72... Quite difficult and pretty costly!
The only way out is to use some smaller vehicles. These vehicles operate at much lower speeds and weights
than an aircraft. Then comes the problem of correlating figures obtained from these measuring vehicles and
actual braking performance of an aircraft. The adopted method was to conduct some tests with real aircraft
and to compare results with those obtained from measuring vehicles.
Results demonstrated poor correlation. For instance, when a Tapley meter reads 0.36, a MU-meter reads
0.4, a SFT reads 0.43, a JBD 12... To date, scientists have been unsuccessful in providing the industry with
reliable and universal values. Tests and studies are still in progress.
As it is quite difficult to correlate the measured with the actual one, termed as effective , measured is
termed as reported .
In other words, one should not get confused between:
1. Effective : The actual friction coefficient induced by tire/runway surface interaction between a given aircraft
and a given runway, for the conditions of the day.
2. Reported : Friction coefficient measured by measuring vehicle.
Particularities of fluid contaminants
Moreover, aircraft braking performance on a runway covered by a fluid contaminant (water, slush and loose
snow) does not depend only on the friction coefficient .
Equivalent runway status
Braking action Friction coefficient Take-off Landing
Good 0,40 and above 1 1
Good/medium 0,39 to 0,36 2 2
Medium 0,35 to 0,30 3/6 5/6
Medium/Poor 0,29 to 0,26 4 5
Poor 0,25 and below 7 7
Unreliable Unrel iable 8 8
E. Performance 46
The model of aircraft braking performance (takeoff and landing) on a contaminated runway takes into account
not only the reduction of a friction coefficient but also:
The displacement drag
The impingement drag
These two additional drags (required to be taken into account by regulations) require knowing type and depth
of the contaminant.
In other words, even assuming the advent of a new measuring friction device providing a reported equal to effective
, it would be impossible to provide takeoff and landing performance only as a function of reported . ATR would
still require information regarding the depth of fluid contaminants.
6.3. Data provided by ATR
Please refer to FCOM section Performances for further details on contaminated runway performance.
Hard contaminants
For hard contaminants, namely compacted snow and ice, ATR provides corrections to apply independently
of the amount of contaminants on the runway. Behind these terms are some effective . These two sets of
data are certified.
Fluid contaminants
ATR provides takeoff and landing corrections on a runway contaminated by a fluid contaminant (water, slush
and loose snow) as a function of the depth of contaminants on the runway.
In other words, pilots cannot get the performance from reported or Braking Action.
Pilots need the type and depth of contaminant on the runway.
7. Aircraft directional control
The previous section analyzes impact of the reduction of friction forces on aircraft braking performance.
The reduction of friction forces also significantly reduces aircraft directional control.
One should also consider the effect of the crosswind component on a slippery runway.
7.1. Influence of slip ratio
When a rolling wheel is yawed, the force on the wheel can be
resolved in two directions: one in the direction of wheel motion,
the other perpendicular to the motion. The force in direction of the
motion is the well-known braking force. The force perpendicular to
the motion is known as the side-friction force or cornering force.
Steering capability is obtained via the cornering force.
Maximum cornering effect is obtained from a free-rolling wheel,
whereas a locked wheel produces zero cornering effect. With
respect to braking performance, we can recall that a free-rolling
wheel produces no braking. In other words, maximum steering
control is obtained when brakes are not applied. One realizes that
there must be s ome compromise between cornering and braking.
The following figure illustrates this principle. It shows that when
maximum braking efficiency is reached (i.e. 12% slippage), a
significant part of the steering capability is lost.
Cornering force
Aircraft
motion
Braking force
TOP VIEW
Yaw angle
Friction force
E. Performance
E. Performance 47
This is not a problem on a dry runway, where the total friction force, split in braking and cornering, is high
enough. It may however be a problem on a slippery runway, where the total friction force is significantly
reduced. In some critical situations, the pilot may have to choose between braking or controlling the aircraft;
both may not be efficient at the same time.
7.2. Influence of wheel yaw angle
The cornering force also depends on the wheel yaw angle. The wheel yaw angle is defined as the angle
between the wheel and its direction of motion. The cornering force increases with the yaw angle, however
if the wheel is yawed too much, the cornering force rapidly decreases. The wheel yaw angle providing the
maximum cornering force depends on the runway condition and diminishes when the runway is very slippery.
It is around 8 on a dry runway, 5 on a slippery runway and 3 on an icy runway.
8. Performance determination
ATR provides data to compute take-off and landing on contaminated runways. They look like distance penal-
ties to apply to normal computation. See FCOM section 3.03.08 for takeoff correction and FCOM section
3.08.03 for landing distances.
Note that FOS, the ATR flight planning software is able to compute more accurate performance charts.
The following example illustrates FOS method and is based on these assumptions:
Blagnac airport runway 32L
TORA: 3500 m
TODA: 3800 m
ASDA: 3800 m
Slope: 0,1%
QNH: 1019
Contaminant: water or slush
1
/
4
inch
Cornering force
Aircraft
motion
Braking force
DRY RUNWAY
Yaw angle
Friction force
Cornering force
Aircraft
motion
Braking force
CONTAMINATED RUNWAY
Yaw angle
Friction force
Free rotation
Locked Wheel
SLIP-RATIO PERCENTAGE
F
R
I
C
T
I
O
N
F
O
R
C
E
12%
BRAKING
CORNERING
:-------------------------------------------------------------------------------------------------:
: F15 : 19/09/2003 BLAGNAC : LFBO 32L :
:-------------------------------------------------------------------------------------------------:
: ELEVATION= 499.0(FT) LIMITATION CODES : ATR42-300 JAR-DGAC:
: T.O.R.A. = 3500.0(M ) 0-DRY CHECK 5-TYRE SPEED : :
: A.S.D.A. = 3800.0(M ) 1-STRUCTURE 6-BRAKE ENERGY : V2/VS OPTIMIZED V1/VR OPTIMIZED:
: T.O.D.A. = 3800.0(M ) 2-2ND-SEGMENT 7-RWY 2 ENGINES : AIR COND. OFF :
: SLOPE = -0.10( %) 3-RUNWAY 8-FINAL T.O. : NORMAL CONDITIONS :
: 4-OBSTACLE 9-VMC : WITHOUT REVERSE :
:-------------------------------------------------------------: :
: : :
: : :
: : :
: : :
:-------------------------------------------------------------:-----------------------------------:
: - WIND: TOW(KG) DTOW1/DTOW2 QNH=1019.00(HPA) : WATER OR SLUSH 1/4 INCH (6.3 MM) :
:O - KT : V1 VR V2(IAS KT) CODES DQNH= +10/ -10 : SCREEN HEIGHT 15 FT :
:A - : DV1 DVR DV2/DV1 DVR DV2 : DRY CHECK :
:T - :-----------------------------------------------------:-----------------------------------:
:(DC) -: -10 : -5 : 0 : 10 : 20 :
:-------:-----------------:-----------------:-----------------:-----------------:-----------------:
: -10.0 :15736 +50/ -51:16135 +51/ -51:16516 +51/ -52:16773 +52/ -52:16900 +0/ +0:
: : 103 103 110 4-4 : 105 105 111 4-4 : 104 104 110 4-4 : 105 105 111 4-4 : 100 101 108 1-1 :
: :+0 +0 +0/+0 +0 +0:+0 +0 +0/+0 +0 +0:+0 +0 +1/+0 +0 +0:+0 +0 +1/+0 +0 +0:-1 +0 +0/+0 +0 +0:
:-------:-----------------:-----------------:-----------------:-----------------:-----------------:
: 0.0 :15526 +52/ -53:15923 +53/ -53:16303 +53/ -54:16559 +54/ -54:16802 +54/ -55:
: : 102 102 109 4-4 : 104 104 110 4-4 : 103 103 110 4-4 : 104 104 111 4-4 : 105 105 111 4-4 :
: :+1 +1 +0/+0 +0 +0:+0 +0 +1/+0 +0 +0:+1 +1 +0/+0 +0 +0:+1 +1 +0/+0 +0 -1:+0 +0 +1/+0 +0 +0:
:-------:-----------------:-----------------:-----------------:-----------------:-----------------:
: 5.0 :15425 +53/ -54:15822 +54/ -54:16201 +54/ -55:16457 +55/ -55:16699 +55/ -56:
: : 102 102 108 4-4 : 101 101 108 4-4 : 103 103 109 4-4 : 104 104 110 4-4 : 105 105 111 4-4 :
: :+0 +0 +1/+0 +0 +0:+3 +3 +2/+0 +0 +0:+0 +0 +1/+0 +0 +0:+0 +0 +0/+0 +0 +0:+0 +0 +0/+0 +0 +0:
:-------:-----------------:-----------------:-----------------:-----------------:-----------------:
: 10.0 :15323 +55/ -56:15720 +56/ -57:16098 +57/ -57:16354 +57/ -58:16595 +57/ -58:
: : 102 102 108 4-4 : 101 101 108 4-4 : 103 103 109 4-4 : 104 104 110 4-4 : 105 105 111 4-4 :
: :+0 +0 +0/+0 +0 +0:+0 +0 +0/+0 +0 -1:+0 +0 +0/-1 -1 +0:+0 +0 +0/-1 -1 +0:+0 +0 +0/-1 -1 +0:
:-------:-----------------:-----------------:-----------------:-----------------:-----------------:
: 15.0 :15222 +58/ -59:15619 +58/ -59:15995 +59/ -60:16251 +59/ -60:16491 +59/ -61:
: : 101 101 108 4-4 : 101 101 107 4-4 : 102 102 109 4-4 : 103 103 110 4-4 : 104 104 110 4-4 :
: :+1 +1 +0/+0 +0 -1:+0 +0 +0/+0 +0 +0:+1 +1 +0/+0 +0 -1:+1 +1 +0/+0 +0 -1:+0 +0 +1/+0 +0 +0:
:-------:-----------------:-----------------:-----------------:-----------------:-----------------:
: 20.0 :15124 +61/ -62:15520 +61/ -62:15896 +62/ -63:16151 +62/ -63:16391 +63/ -64:
: : 101 101 107 4-4 : 101 101 107 4-4 : 102 102 108 4-4 : 103 103 109 4-4 : 104 104 110 4-4 :
: :+0 +0 +1/+0 +0 +0:+0 +0 +0/-1 -1 +0:+0 +0 +0/+0 +0 +0:+0 +0 +0/+0 +0 +0:+0 +0 +0/+0 +0 +0:
:-------:-----------------:-----------------:-----------------:-----------------:-----------------:
/OBSTACLE FROM BEGINNING OF TORA : DISTANCE(M )/HEIGHT(FT)
/ 4145/ 309 4155/ 307 4160/ 310 4180/ 311 4545/ 316
/MINI. ACCELERATION HEIGHT : 502.(FT) QNH ALT. : 1001.(FT)
/MAXI. ACCELERATION HEIGHT : 3551.(FT) QNH ALT. : 4050.(FT)
FOS WINDOWS 4.0.3 /TLC:M1 APR.2003 AT00G76U.PDF ATR42*00/AA/PW-120 T00/15-AR-BY8.-JA
Example of a FOS take-off performance chart for a contaminated runway
E. Performance 48
F. Procedures
F. Procedures 49
F. Procedures 50
1. Parking
When leaving the aircraft parked in cold weather conditions, some precautions need to be taken for the safety
of the following flight. Refer to the Service Letter SL 30-5011 for ATR 42 aircraft and SL 30-6004 for ATR
72 aircraft for the detailed procedures.
The main points to remember are to protect the exposed airframe parts, and especially the engine, the wheels,
the blades and the gears against the snow or ice accumulation. And to remove the standing water that could
freeze from the critical parts, notably the flaps hinges.
2. Exterior inspection
2.1. Walk-around
An exterior inspection of the aircraft is performed before each flight. For cold weather operation, the crew
must be particularly vigilant and shall not forget to check the following parts of aircraft. If the crew detects
ice or pollution on ANY surface, de-icing and anti-icing procedures are required.
engine inlets
engines cowling and draining
propellers
pack inlets
landing gear assemblies
landing gear doors
pitot, and static vents
angle of attack sensors
fuel tank vents
It is essential that the following aerodynamical surfaces are checked clear of ice or snow too:
fuselage
wings
vertical and horizontal stabilizer
control surfaces
2.2. Frost due to condensation
Light hoar frost can appear under fuel tanks with winter
anticylonic conditions and light wind. This phenomenon is
induced by a difference of temperature between wing skin
and fuel inside tanks.
CAUTION: Takeoff is only possible with no more than 2 millimeters of frost
under wings. The rest of the aircraft must be totally clear of frost. Takeoff
must be performed with atmospheric icing speeds and performance penalties
must be applied. It is the Captains responsibility to assess the undersurface
of the wings before initiating a takeoff with the undersurface polluted.
F. Procedures
F. Procedures 51
3. Cockpit preparation
3.1. Cold weather operation
Apply normal procedures plus the following items:
Provided air intake and both pack inlets are free of snow,
frost, ice, start engine 2 in Hotel Mode
In order to quickly improve cabin warm up, select the
overboard valve to full close position.
With this position selected, the overboard valve drives hot
avionics cooling flow to the cabin, thus increasing quickly
cabin temperature.
3.2. Permanent anti-icing
Before each flight, the crew must select permanent anti-
icing ON (level 1): probes and front windshield are heated
to prevent ice building up.
4. Taxi
4.1. Taxi procedure
ATR recommends both engines taxi procedures,
particularly in case of contaminated runways:
To avoid skidding by using differential power
when friction coefficient is low (especially when
OAT is very low).
To allow a good warm-up of engine n1 before
takeoff.
4.2. Caution
Nose wheel deflection must be used with little variations. Observe special care with thick contaminant layer.
In this case, apply the following procedure to avoid landing gear damage:
Set 18% of torque on both engine
Use brakes to maintain a speed down to a walking pace for 30 seconds with 18% of torque. In this way,
brakes temperature increases and eliminates any contamination on landing gear assemblies.
Use nose wheel steering with little variations to ensure symmetrical brake warming.
Anti-icing fluids film disruption on canted surfaces implies a reduced holdover time. Therefore, FAA notice
8900 Revised FAA-Approved Deicing Programs Updates, Winter 2010-2011 recommends to delay take-off
flaps extension as appropriate.
Avionic vent panel with overboard valve on
full close
Permanent anti-icing panel selected ON for
every flight
F. Procedures 52
5. Take-off
Icing conditions and contaminated runways introduce operational constraints. Thus to ensure both safety
and payload maximization at takeoff, crew have to focus on some important points, developed in the current
chapter. A synoptic table summarizes take-off situations.
5.1. Take-off in atmospheric icing conditions
According to FCOM 2.02.08 the crew must select anti-icing ON to prevent ice accretion on airframe. As
soon as anti-icing is ON, what is confirmed by the ICING AOA light ON, the crew must monitor speed to
stay in the flight envelope.
Furthermore takeoff speeds are increased while ICING AOA light is ON, leading to performance reduction.
NOTE: The take-off is assumed to last until the aircraft has reached 1500ft AGL or when 10 minutes elapsed from brakes release,
whichever occurs first.
When the icing conditions are met after this point, the take-off is performed in normal conditions. The take-off
performance, and the payload are thus maximized. Once the take-off sequence is completed and when the
icing conditions are met, the anti-icing and de-icing systems are switched ON and the icing speeds are set.
5.2. Take-off on contaminated runways
In this case the crew has to select propellers anti-icing only. This is to prevent ice formation on blades induced
by projection of contaminants such as slush or snow. Thus, takeoff performances are optimum.
Furthermore landing gears must be cycled after takeoff to avoid ice accretion on rods and paddles.
5.3. Fluid type II and fluid type IV particularities
These fluids present a high viscosity to increase the holdover time protection and can thus increase stick
forces at the aircraft rotation: these control forces may be more than twice the normal takeoff force. This
should not be interpreted as a pitch jam leading to an unnecessary abort decision above V1. Although
not systematic, this phenomenon should be anticipated and discussed during pre-takeoff briefing each time
de-icing/anti-icing procedures are performed. These increased pitch forces are strictly limited to the rotation
phase and disappear after takeoff. Refer to FCOM 2.02.08 for further information on the pitch jam matter.
In very exceptional circumstances, because of increased rotation forces, the pilot can consider that takeoff is
impossible and consequently initiate an aborted takeoff.
To handle this problem, ATR provides two methods described in AFM appendices.
Method 1: This method applies to a crew who has not received a specific training. In this case the crew
applies the standard takeoff procedure, but TOD, TOR and ASD are increased by 20% on ATR 42 and
25% on ATR 72.
Method 2: This method applies to a crew who has received a specific training. In this case, the crew has
to perform a specific briefing to review possible increased stick forces during rotation. If this happens the
captain request the first officers assistance. He orders pull and the first officer pull the control wheel
until pitch reaches 5. Proceeding in such a way minimizes takeoff penalties. 70m only are added to the
takeoff distance.
NOTE: Increased stick forces during rotation may be reinforced with forward CGs.
F. Procedures
F. Procedures 53
A
p
p
l
y

n
o
r
m
a
l

p
r
o
c
e
d
u
r
e

+

t
h
e
s
e

f
o
l
l
o
w
i
n
g

i
t
e
m
s
:

I
c
i
n
g

s
p
e
e
d
s

b
u
g
s

s
e
t

A
n
t
i
-
i
c
i
n
g

O
N

R
e
s
p
e
c
t

i
c
i
n
g

s
p
e
e
d
s
(
r
e
d

b
u
g

f
o
r

t
h
e

f
l
a
p
s

r
e
t
r
a
c
t
i
o
n
)

D
e
t
e
r
m
i
n
e

t
a
k
e
-
o
f
f

d
a
t
a

w
i
t
h

i
c
i
n
g

c
o
n
d
i
t
i
o
n
s
.
G
R
O
U
N
D

I
C
I
N
G

C
O
N
D
I
T
I
O
N
S
W
I
T
H
O
U
T

A
T
M
O
S
P
H
E
R
I
C

I
C
I
N
G

C
O
N
D
I
T
I
O
N
S
A
p
p
l
y

n
o
r
m
a
l

p
r
o
c
e
d
u
r
e

+

t
h
e
s
e

f
o
l
l
o
w
i
n
g

i
t
e
m
s
:
T
a
x
i
C
o
n
t
a
m
i
n
a
n
t

m
a
y

a
d
h
e
r
e

t
o

w
h
e
e
l

b
r
a
k
e
s

w
h
e
n

t
a
x
i
i
n
g

o
n

c
o
n
t
a
m
i
n
a
t
e
d

r
a
m
p
,

t
a
x
i
w
a
y
s

a
n
d

r
u
n
w
a
y

i
n

t
h
i
s

c
a
s
e

a
p
p
l
y

t
h
i
s

s
p
e
c
i
a
l

f
o
l
l
o
w
i
n
g

p
r
o
c
e
d
u
r
e
:
S
e
t

1
8
%

t
o
r
q
u
e

o
n

e
a
c
h

e
n
g
i
n
e

a
n
d

k
e
e
p

t
a
x
i

s
p
e
e
d

d
o
w
n

t
o

a

w
a
l
k
i
n
g

p
a
c
e

f
o
r

3
0

s
e
c
o
n
d
s

u
s
i
n
g

n
o
r
m
a
l

b
r
a
k
e

a
c
t
i
o
n

w
i
t
h

m
i
n
i
m
u
m

u
s
e

o
f

n
o
s
e

w
h
e
e
l

s
t
e
e
r
i
n
g

t
o

e
n
s
u
r
e

a

s
y
m
m
e
t
r
i
c
a
l

w
a
r
m
i
n
g

u
p

o
f

t
h
e

b
r
a
k
e
s
.
B
e
f
o
r
e

t
a
k
e
-
o
f
f

P
r
o
p

a
n
t
i
-
i
c
i
n
g

O
N
A
f
t
e
r

t
a
k
e
-
o
f
f

L
a
n
d
i
n
g

g
e
a
r

r
e
c
y
c
l
e
N
O
T
E
:

S
p
e
c
i
a
l

p
r
o
c
e
d
u
r
e

f
o
r

t
h
e

l
a
n
d
i
n
g

D
e
t
e
r
m
i
n
e

t
a
k
e
-
o
f
f

d
a
t
a

w
i
t
h

c
o
n
t
a
m
i
n
a
t
e
d

r
u
n
w
a
y

c
o
m
p
u
t
a
t
i
o
n

c
h
a
r
t
s
W
H
E
N

U
S
I
N
G

A
N
T
I

&

D
E
-
I
C
I
N
G

F
L
U
I
D

T
Y
P
E
S

I
I

&

I
V
A
f
t
e
r

g
r
o
u
n
d

a
n
t
i
-
i
c
i
n
g

p
r
o
c
e
d
u
r
e
,

u
s
i
n
g

t
y
p
e

I
I

&

I
V

f
l
u
i
d
s
,

h
i
g
h
e
r

t
h
a
n

n
o
r
m
a
l

s
t
i
c
k

f
o
r
c
e
s

m
a
y

b
e

e
n
c
o
u
n
t
e
r
e
d
.

A
T
R

A
F
M

p
r
o
v
i
d
e
s

t
w
o

f
l
i
g
h
t

p
r
o
c
e
d
u
r
e
s

d
e
p
e
n
d
i
n
g

o
n

c
r
e
w

t
r
a
i
n
i
n
g
.
M
E
T
H
O
D

1
P
i
l
o
t
s

w
i
t
h
o
u
t

s
p
e
c
i
f
i
c

t
r
a
i
n
i
n
g

A
p
p
l
y

n
o
r
m
a
l

p
r
o
c
e
d
u
r
e

M
E
T
H
O
D

2
P
i
l
o
t
s

w
i
t
h

s
p
e
c
i
f
i
c

t
r
a
i
n
i
n
g

A

s
p
e
c
i
f
i
c

b
r
i
e
f
i
n
g

b
e
f
o
r
e

t
a
k
e
-
o
f
f

m
u
s
t

b
e

c
o
m
p
l
e
t
e
d

T
h
e

C
a
p
t
a
i
n

i
s

t
h
e

p
i
l
o
t

f
l
y
i
n
g
.

I
n

c
a
s
e

o
f

d
i
f
f
i
c
u
l
t
i
e
s

t
o

r
o
t
a
t
e
,

t
h
e

C
a
p
t
a
i
n

s
h
o
u
l
d

r
e
q
u
i
r
e

t
h
e

F
i
r
s
t

O
f
f
i
c
e
r
s

a
s
s
i
s
t
a
n
c
e
.
C
P
T

o
r
d
e
r
s

P
U
L
L
:

F
i
r
s
t

O
f
f
i
c
e
r

h
e
l
p
s

t
h
e

C
a
p
t
a
i
n

t
o

p
u
l
l

t
h
e

c
o
n
t
r
o
l

w
h
e
e
l

u
n
t
i
l

p
i
t
c
h

r
e
a
c
h
e
s

5
.
M
E
T
H
O
D

1

D
e
t
e
r
m
i
n
e

V
r

f
o
r

l
o
w
e
s
t

a
v
a
i
l
a
b
l
e

V
2

&

a
s
s
u
m
e

V
1
=
V
r

I
n
c
r
e
a
s
e

T
O
R
,

T
O
D
,

A
S
D

b
y

2
0
%

f
o
r

A
T
R

4
2
,

a
n
d

2
5
%

f
o
r

A
T
R

7
2
M
E
T
H
O
D

2

I
n
c
r
e
a
s
e

T
O
D

b
y

8
0
m

f
o
r

A
T
R

4
2
-
5
0
0

a
n
d

7
0
m

f
o
r

o
t
h
e
r

A
T
R
.
A
I
R

S
P
E
E
D

E
F
F
E
C
T
A
n
t
i
-
i
c
i
n
g

f
l
u
i
d
P E R F O R M A N C E F L I G H T O P E R A T I O N S
T
A
K
E
-
O
F
F

I
N

C
O
L
D

W
E
A
T
H
E
R
F. Procedures 54
6. Flight profile in icing conditions
This diagram is a sum-up of the different procedures for flight in atmospheric icing conditions that can be
found in FCOM 2.02.08:
Entering icing conditions
At first visual indication of ice accretion and as long as icing conditions exist
Leaving icing conditions
When the aircraft is visually verified clear of ice
6.1. Entering icing conditions
Operations in atmospheric icing conditions require special care since ice accretion on airframe and propellers
significantly modify their aerodynamic characteristics. To avoid such problems, the crew must select anti-icing
level ON (level 2) as soon as aircraft reaches icing conditions.
Icing conditions definition:
Visible moisture
Temperature SAT
<
5 C on ground or at take-off
TAT
<
7 C in flight
Visibility less than 1 Nm
By depressing one of both horns push buttons to the ON position, ICING AOA green light appears auto-
matically, alerting the crew that the stall threshold alarm has been decreased
In normal operations the stick shaker threshold is set at ~12 of angle of attack to prevent stall with flaps 0.
When ICING AOA light is ON, stick shaker threshold is reduced at ~7.
FA|T
lOlNG
lOlNG
AOA
FA|T
lOlNG
lOlNG
AOA
FA|T
lOlNG
lOlNG
AOA
lOlNG
AOA
FA|T
lOlNG
FA|T
lOlNG
lOlNG
AOA
lOlNG
AOA
FA|T
lOlNG
Conditions
Speeds Normal Icing Icing Icing Normal
Cont. relight (only for
ATR 42-300 & 72-200)
As required As required ON As required As required
Non icing
conditions
Entering icing
conditions
Leaving icing
conditions
At 1st visual indication
of ice accretion and as long
as icing conditions exist
When the aircraft
is visually veried
clear of ice
Permanent protection
Anti-icing protection
De-icing protection
Level protection
Release
With residual
ice on the
aircraft (IEP
or propeller
spinners)
Icing light
(ice accretion
detected)
Icing AOA
(stall warning
threshold reduced)
1 1 2 1 1 1 2 3
P
A
1
2
3 TAT 7 C
ice accretion end of
ice accretion
F. Procedures
F. Procedures 55
Under FAA regulation Eng 1 and 2 de-icing must be engaged while in icing conditions
6.2. At 1st visual indication of ice accretion and as long
as icing conditions exist
6.2.1. Ice accretion
Aircraft enters in ice accretion area, at first sign
of ice building up on any part of the airframe.
The Ice Evidence Probe and the Ice detector
are two supplementary devices to help the crew
detecting such situation:
Ice evidence probe (primary mean)
This component is located near the cockpit left
side window. When encountering ice accretion,
ice builds up on the leading edge of this probe
allowing visual detection. An integrated lighting
controlled by the NAV LIGHT switch has been
included for night operations.
Some ATR 42 may not be equipped with an IEP. In this case, the propeller spinners are the primary mean
of detection.
Ice detector
The ice detector electronic sensor is located under left wing, and alerts the crew with a single chime, a master
caution and an icing amber light as soon as ice accretion is sensed. If ice accretion is detected with horns
anti-icing and/or airframe de-icing still OFF the icing light will flash until the crew select both anti-icing and
de-icing systems ON. The icing light remains steady ON as long as ice builds upon the aircraft.
F. Procedures 56
6.2.2. End of ice accretion
In icing conditions, even if ice accretion stops, crew must maintain anti-icing and deicing ON (level 2 and
3) for many reasons:
To anticipate further ice accretion areas
To keep aircraft in the flight envelope (due to ice on airframe, aerodynamic characteristics could change).
Blue memo de-icing light will flash 5 minutes after the last detection of ice accretion by the ice detector.
This must be disregarded and de-icing systems must remain ON until icing conditions are left.
Ice detector panel with both
ICING AOA and ICING light ON
Anti-icing and de-icing panels with systems
ON (level 2 and 3)
Anti-icing and de-icing panels with systems
ON (level 2 and 3)
Ice detector panel
with ICING AOA light ON
Reset of ICING AOA
F. Procedures
6.3. Leaving icing conditions
One can consider leaving icing conditions when:
Total Air Temperature (TAT) is above 7 C
And/Or
Aircraft is flying without visible moisture
When leaving icing conditions, crew selects anti-icing and de-icing systems OFF and continues flying with
ICING AOA light ON until aircraft is checked clear of ice.
6.4. When the aircraft is visually verified clear of ice
As soon as normal conditions are recovered (temperature, visibility), airframe condition must be monitored.
If the Ice Evidence Probe (IEP) is checked clear of ice, this means that there is no more ice on the critical
airframe surfaces. (If the IEP is not installed, the propeller spinner shall be used as a visual mean.)
Thus depress ICING AOA light. When ICING AOA light is OFF, normal flight conditions are recovered and
normal operating speeds must be applied.
Anti-icing and de-icing panels
with systems OFF
Ice detector panel
with ICING AOA light ON
F. Procedures 57
7. Procedures following APM alerts
The APM aims at drawing the attention of the flight crew to a potential risk of ice accretion. It does not
replace the previous procedures, which details how to manage the flight profile in icing conditions, but it helps
to detect when the aircraft is facing severe icing conditions.
APM and its associated alerts are additional means to detect the ice accretion, but do not replace the general
methodology for flight in icing conditions.
CRUISE SPEED LOW
This alert is an advisory alert to warn the flight crew to monitor potential ice accretion. The associated proce-
dure is detailed in the QRH normal procedures.
DEGRADED PERF.
This alert is a caution alert triggered in cruise or in climb to warn the flight crew of an abnormal decrease in
the aircraft speed, that can be caused by ice accretion on the aerodynamic parts of the aircraft. The flight
crew has to switch on the de-icing systems and to determine if the atmospheric icing conditions are confirmed.
The associated procedure is detailed in the QRH following failures procedures.
INCREASE SPEED
This alert is a caution alert triggered in flight to warn the flight crew of an abnormal decrease in the aircraft
speed, that can be caused by ice accretion. The flight crew has to check if the abnormal conditions are
observed, and once confirmed, they have to recover the aircraft speed immediately.
The associated procedure is detailed in the QRH following failures procedures.
F. Procedures 58
G. Severe icing
G. Severe icing 59
G. Severe icing 60
1. Overview
Current certification standards for icing call for protection against ice accretions generated within a certain
icing envelope defined in the Appendix C of JAR/FAR25. Icing conditions in clouds were established as
being satisfactory standards for the design and the certification of airplane ice protection provisions. However
atmospheric icing conditions are highly variable and can exceed these standards. An aircraft certified for flight
into known icing conditions may transit into more severe icing conditions. Under these conditions, the ice
protection systems may not be able to adequately protect the aircraft.
The AIM 7-20 provides the following definition for the icing severity index: Severe. The rate of accumulation is such that
de-icing/anti-icing equipment fails to reduce or control the hazard. Immediate flight diversion is necessary.
The icing conditions are characterized by their median volumetric diameters of droplets, the liquid water content,
the outside air temperature and the time of exposure. Exceedance of one of these parameters may lead to
accumulation of ice either beyond the capacity of the ice protection systems or in locations not normally prone
to icing and not protected. In this case the ice protection provisions may no longer be effective to provide
safe operations and the flight crew may be required to promptly exit these conditions.
The current certification standards for icing refer to supercooled clouds having droplets of a median diameter
(MVD) between 15 and 50 microns. In this view icing conditions involving larger droplet diameter such as
Supercooled Large Droplets (SLD) may be considered as severe icing conditions.
1.1. Supercooled large droplet
Freezing rain and freezing drizzle are forms of SLD. These conditions are observed and forecast as surface
conditions. They are typically found below 10,000 feet AGL. However, SLD may exist at altitude and not be
detected on the surface. Pilots have reported SLD encounters up to 18,000 feet. Ice pellets on the surface
also frequently indicate the presence of SLD aloft, but SLD conditions at altitude may be completely unde-
tectable from the ground.
Two different atmospheric conditions result in the formation of freezing rain and freezing drizzle:
Temperature inversion
Collision-coalescence Process
1.2. Temperature inversion
Ordinarily, temperatures decrease with altitude. However,
when there is a temperature inversion, this is not the
case. A layer of cold air lies under a layer of warmer air.
Temperature inversions are most often associated with
warm fronts and stationary fronts.
Freezing rain and occasionally freezing drizzle can form
when liquid water dropsfall from an area of warm air through
a layer of air that is at or below freezing.
1.3. Collision-coalescence process
Freezing drizzle is more often formed via the collision-coalescence process, than temperature
inversion. Through condensation, some droplets within the clouds may grow in diameter, begin
to settle, and fall fast enough to collide with smaller, slower moving droplets to coalesce and
form bigger droplets. These droplets can be found throughout the entire depth of the cloud.
This process is more likely to occur when the cloud temperatures are warmer than 15 C.
Supercooled Large Droplets (SLD) can be 100 times larger than the droplets to be considered
in the current certification standards
TEMPERATURE (C)
-5 -4 -3 -2 -1 0 1 2 3 4
ALTITUDE
Freezing
drizzle
area
Melting
layer
Frontal
layer
2
,
0
0
0

t
o

3
,
0
0
0

f
t
G. Severe icing 61
Certification Standards
Droplets diameter from 5 to 135 microns
MVD from 15 to 50 microns
Supercooled Large Droplets
Droplets diameter from 5 to 2000 microns
MVD from 15 to 2000 microns
Droplet trajectory relative to the aircraft is governed by aerodynamic forces
acting on the droplet and its inertia. The opposite chart evidences how small drop-
lets, essentially following the streamlines will escape the airfoil except close to the
stagnation point, when the much heavier larger droplets will tend to go straight, with
a significantly extended accretion coverage.
200 microns versus 40 microns:
Droplet aerodynamic drag x 25
Droplet inertia x 125
Large droplets will also tend to stream back before freezing, further extending the
coverage of the resulting ice accretion.
The extent of the ATR wing de-icing boots is such as it is unlikely to accrete ice
beyond the protection on the upper surface. Nevertheless under these SLD condi-
tions ice may accrete aft of the protected area on the lower surface and the whole
boots extent may be covered with residual ice.
Case of severe icing conditions: the whole chordwise extent
of the boot is covered with ice.
2. Detection of SLD
2.1. Conditions conducive to SLD
The following weather conditions may be a sign of SLD encounters:
Visible water precipitation at temperatures close to 0 C ambient air temperature (SAT)
Droplets that splash or splatter on impact on cockpit windows at temperatures close to 0 C ambient air
temperature
2.2. Visual Cues
SLD encounters have been experienced several times on ATR during either flight test campaigns or commercial
flights and the following visual cues were established:
Ice spots covering all or a substantial part of the unheated portion of either forward side windows, possibly
associated with water splashing and streaming on the windshields
Unexpected decrease in speed or rate of climb
SLD
Certification
Standards
Stagnation point
AIRFOIL
Droplet trajectories
40 microns
Droplet trajectories
200 microns
Streamlines
Streamlines
Stagnation point
AIRFOIL
SLD- Total coverage
of the unheated part
of the side window.
The yellow color is
due to the water used
during tanker tests.
SLD - Partial
coverage of
the unheated
part of the side
window
SLD
G. Severe icing
G. Severe icing 62
Speed and ROC decreases
The following may be used as secondary indications of SLD encounters:
Unusually extensive ice accretion on the airframe in areas not normally observed to collect ice,
Accumulation of ice on the propeller spinner farther aft than normally observed,
Accumulation of ice on the lower surface of the wing aft of the protected areas.

SLD - Underwing ice accretion SLD - Ice accretion on the propeller spinner
3. Procedure
In case of severe icing, the crew must apply the SEVERE ICING emergency procedure, contained in AFM 4.05.
Each step of this procedure is explained below.
INCREASE ICING SPEED BY 10KTS
During a severe Ice exposure, the icing atmosphere can create conditions beyond the ability of the aircraft
system to withstand. Ice will be accreting faster than the deicing system can get rid of it. The airfoil shape will
be changed and the stall warning system may not activate before the wing stall. It is to avoid this circumstance
that an additional safety margin of 10kts is added. Remember to apply conservative maneuvering speed any
time needed (refer to FCOM 2.02.01 Operating speeds).
PWR MGT SET TO MCT
Severe Ice on the aircraft increases the drag enormously, max available power will be required. Set CL/PL at 100%/MCT.
As power equal NP multiplied by TQ, it is mandatory to set both CL/PL at their maximum continuous values.
FIRMLY HOLD CONTROL WHEEL AND DISENGAGE AP
The AP may mask tactile cues that indicate adverse changes in handling characteristics. Full aileron trim may
be required so if the AP does not disengage automatically because of the unusual trim requirement, when
disengaged manually expect strong control column forces to avoid an aircraft upset.
ESCAPE SEVERE ICING CONDITIONS
Always plan the escape route when first encountering any ice accretion, anticipate conditions deteriorating.
Severe Ice atmosphere is usually very localised, climb (if possible) or descend (if terrain clearance allows). An
increase of 1 C may be sufficient for escape.
Change heading based on information provided by ATC.
Speed (kt)
E
x
p
e
c
t
e
d

c
l
i
m
b

p
r
o
f
i
l
e
Alt.(ft)
Time in severe icing
IAS
G. Severe icing
G. Severe icing 63
NOTIFY ATC
If an unusual roll response or uncommanded roll control movement is observed.
This is standard ATR stall symptoms which require stall recovery by:
Pushing firmly on the control wheel
Setting flaps 15
Both actions reduce the angle of attack.
If the flaps are extended, do not retract them until the airframe is clear of ice.
Accretions collected with flaps 15 were found to be further aft and more severe than flaps 0. Indeed, in
flaps 15 configuration, the low angle of attack especially close to VFE increases the exposure of the
upper side to large droplet impingement.
After this exposure, retracting flaps from 15 to 0 would increase the angle of attack, and the airflow could
easily disrupt from the contaminated wing, resulting in a stall.
If the aircraft is not clear of ice, use flaps 15 for landing.
Ice contaminated tail stalls are almost always associated with flaps extension. Lowering the flaps increases
the wing downwash, and thereby greatly increases the horizontal stabilizers angle of attack.
Increasing tailplane angle of attack with ice on the tail can disrupt the airflow under the stabilizer and make the elevator
less effective. The elevator may oscillate without pilot input and cause an uncommanded pitch change.
SEVERE ICING
MINIMUM ICING SPEED ........................................................... INCREASE RED BUG by 10 kt
PWR MGT ......................................................................................................................... MCT
CL/PL ...............................................................................................................100%/ MCT
AP (if engaged) ....................................... FIRMLY HOLD CONTROL WHEEL and DISENGAGE
SEVERE ICING CONDITIONS ...................................................................................... ESCAPE
ATC ............................................................................................................................... NOTIFY
If an unusual roll response or uncommanded roll control movement is observed:
Push firmly on the control wheel
FLAPS ................................................................................................................................... 15
If the flaps are extended, do not retract them until the airframe is clear of ice.
If the aircraft is not clear of ice:
GPWS .................................................................................................................... FLAP OVRD
STEEP SLOPE APPROACH (
>
4.5) ...................................................................... PROHIBITED
APP/LDG CONF ....................................................................................... MAINTAIN FLAPS 15
............................................................ with REDUCED FLAPS APP/LDG icing speeds + 5 kt
Multiply landing distance FLAPS xx by yy, depending on aircraft.
DETECTION
Visual cue identifying severe icing is characterized by ice covering all or a substantial part of the
unheated portion of either side window
and/ or
Unexpected decrease in speed or rate of climb
and/ or
The following secondary indications:
Water splashing and streaming on the windshield
Unusually extensive ice accreted on the airframe in areas not normally observed to collect ice
Accumulation of ice on the lower surface of the wing aft of the protected areas
Accumulation of ice on propeller spinner farther aft than normally observed
The following weather conditions may be conducive to severe in-flight icing:
Visible rain at temperatures close to 0C ambient air temperature (SAT)
Droplets that splash or splatter on impact at temperatures close to 0C ambient air temperature (SAT).
Appendices 64
Appendices
Appendices 65
Appendices
Appendix 1. Quizz
Questions
1. How can the pilot know that his aircraft is
free of ice?
a) When wings are free of ice
b) When Ice Evidence Probe is visually checked
free of ice
c) When TAT is above 7C, and/or the aircraft is
flying outside visible moisture
d) When there is no more ice on the unheated
part of the lateral window
2. Detection of severe icing conditions:
What are the primary visual cues pilots have
to monitor to detect severe icing conditions?
a) Ice spots covering all or a significant part of
the unheated portion of either side window,
possibly associated with splashing or
splattering water streaming off windshields,
and/or unexpected decrease in speed and/or
rate of climb
b) Unusual ice shapes accreting on airframe
parts not usually ice contaminated
c) Accumulation of ice on propeller spinner,
further aft than usually observed
d) Droplets that splash or splatter on window
impact, with SAT close to 0C
3. When pilots apply Severe icing emergency
procedure, first action they must perform is?
a) Increase power to MCT
b) Call ATC, to advise of severe icing conditions
encounter
c) Disconnect auto pilot to detect possible
ailerons and/or elevator behaviour changes
d) Increase icing speed by 10 kt and maintain
this additional safety margin
4. When pilots apply severe icing procedure,
following actions must be applied:
a) do not retract flaps until airframe is free of ice
b) GPWS, set flaps override
c) Approach slope must not exceed 4.5
d) maintain flaps 15 for approach and landing
configurations,
e) All previous answers are correct
5. In case of severe icing, if an unusual or
uncommanded roll control movement is
observed, pilots have to firmly push control
wheel forward and extend flaps to 15.
a) True
b) False
6. There are numerous secondary visual cues
to detect severe icing conditions, one
amongst them is ice accretion rate. Ice
accretion rate is considered as severe,
when the rate of accumulation is:
a) 1 cm of ice accumulation in 15 to 60 minutes
b) 1 cm of ice accumulation in 5 to 15 minutes
c) 1 cm of ice accumulation in less than 5
minutes
7. Holdover times charts are providing
indications regarding protected timeframes
that could reasonably be anticipated with
ongoing atmospheric precipitations.
a) The smallest figure indicates estimated
protection time during heavy precipitations,
while the biggest one refers to light
precipitations.
b) The smallest figure indicates estimated
protection time during light precipitations,
while the biggest one refers to heavy
precipitations.
c) The smallest and biggest figures indicate
minimum and maximum estimated protection
time with atmospheric precipitations.
8. Aircraft is now ready for take-off. Last
METAR figures showing 300m RVR in light
freezing rain. Holdover time charts indicate
a 45 mn time protection. Having conducted
de/ anti-icing operations 25 minutes ago:
a) Crew may take off because aircraft is inside
holdover time protection.
b) Crew may take off because light precipitation
is reported.
c) Crew may take off because, even if light
freezing rain presents a severe icing risk,
aircraft is protected by the anti-icing fluid for
20 minutes after take-off.
d) Crew can not take off because the anti-
icing fluid is solely efficient during ground
operations.
Appendices 66
Answers
1. b) When flight out of icing conditions is resumed, airframe condition must be
checked and continuously monitored, as long as icing risks prevails.
If the IEP is checked free of ice, it means there is no more ice on critical airframe
surfaces.
On aircraft not fitted with IEP, propeller spinner shall be used as a visual cue.
Once and only once airframe has been checked free of ice (IEP or spinners), AOA
green light should be depressed, turning it out thus allowing crew to resume use
of normal operating speeds.
Please refer to paragraph F.6.4. When the aircraft is visually verified clear of ice.
2. a) Supercooled Large Droplets (SLD) encounters have been experienced several
times on ATR during either flight test campaigns or commercial flights, and the
following visual cues were established:
Ice spots covering all or a significant part of the unheated portion of either side
window, possibly associated with splashing or splattering water streaming off
windshields,
and/or unexpected decrease in speed and/or rate of climb
Please refer to paragraph G.2. Detection of SLD.
3. d) First action pilots have to perform when beginning Severe Icing emergency
procedure is to increasing icing speed by 10 kt and maintain this additional safety
margin.
Please refer to paragraph G.3. Procedure.
4. e) An unusual roll response or uncommanded roll control movement are standard
ATR approaches to stalls symptoms requiring to perform stall recovery procedure
by:
Firmly pushing forward the control wheel
Extending flaps to 15
Both actions aim to immediately reduce angle of attack.
Please refer to paragraph G.3. Procedure.
5. a) Please refer to paragraph G.3. Procedure.
6. c) To standardize icing severity encounters reports, different icing severity levels
were determined:
1 cm of ice accumulation in 15 to 60 minutes is the reference for light icing
1 cm of ice accumulation in 5 to 15 minutes is the reference for moderate icing
1 cm of ice accumulation in less than 5 minutes is the reference for severe icing
7. a) Timeframe figures are published to cope with varying existing meteorological
conditions.
8. d) The fluids used during ground de/anti-icing is not intended for and does not provide
protection in flight. During acceleration, the fluids are washed away from wings.
Once airborne, ice protection rely only on aircraft systems. Anti/de-icing systems
do not provide any kind of severe icing protection.
Freezing drizzle or rain is considered as a risk of severe icing conditions.
Appendices
Appendices 67
Appendix 2. Definitions
Anti-icing is a precautionary procedure, which provides protection against the formation of frost or ice and
the accumulation of snow on treated surfaces of the aircraft, for a limited period of time (holdover time).
Anti-icing code describes the quality of the treatment the aircraft has received and provides information to
determine the holdover time.
Aquaplaning or hydroplaning is a situation where the tires of the aircraft are, to a large extent, separated
from the runway surface by a thin fluid film.
Braking action is a report on the conditions of the airport movement areas, providing pilots the quality or
degree of braking that may be expected. Braking action is reported in terms of: good, medium to good,
medium, medium to poor, poor, nil or unreliable.
Clear ice is a smooth compact rime, usually transparent, fairly amorphous, with a ragged surface, and
morphologically similar to glaze.
Contaminated runway: A runway is considered to be contaminated when more than 25% of the runway surface
area (whether in isolated areas or not) within the required length and width being used is covered by the following:
Surface water more than 3 mm (0.125 in) deep, or slush, or loose snow, equivalent to more than 3 mm (0.125 in)
of water; or
Snow which has been compressed into a solid mass which resists further compression and will hold together
or break into lumps if picked up (compacted snow); or
Ice, including wet ice
Damp runway: A runway is considered damp when the surface is not dry, but when the moisture on its
surface does not give it a shiny appearance.
De-icing is a procedure by which frost, ice, slush or snow is removed from the aircraft in order to provide
clean surfaces. This procedure can be accomplished by mechanical methods or pneumatic methods or the
use of heated fluids.
De/Anti-icing is a combination of the two procedures, de-icing and anti-icing, performed in one or two steps.
A de-/anti-icing fluid, applied prior to the onset of freezing conditions, protects against the build up of frozen
deposits for a certain period of time, depending on the fluid used and the intensity of precipitation. With
continuing precipitation, holdover time will eventually run out and deposits will start to build up on exposed
surfaces. However, the fluid film present will minimize the likelihood of these frozen deposits bonding to the
structure, making subsequent de-icing much easier.
Dew point is the temperature at which water vapor starts to condense.
Dry runway: A dry runway is one which is neither wet nor contaminated, and includes those paved runways which
have been specially prepared with grooves or porous pavement and maintained to retain effectively dry braking
action, even when moisture is present.
Fluids (de-icing and anti-icing)
De-icing fluids are:
a) Heated water
b) Newtonian fluid (ISO or SAE or AEA Type I in accordance with ISO 11075 specification)
c) Mixtures of water and Type I fluid
d) Non-Newtonian fluid (ISO or SAE or AEA Type II or IV in accordance with ISO 11078 specification)
e) Mixtures of water and Type II or IV fluid
De-icing fluid is normally applied heated to ensure maximum efficiency.
Appendices 68
Anti-icing fluids are:
a) Newtonian fluid (ISO or SAE or AEA Type I in accordance with ISO 11075 specification)
b) Mixtures of water and Type I fluid
The first two anti-icing fluids are normally applied heated at 60C on clean aircraft surfaces.
c) Non-Newtonian fluid (ISO or SAE or AEA Type II or IV in accordance with ISO 11078 specification)
d) Mixtures of water and Type II or IV fluid
The last two anti-icing fluids are normally applied unheated on clean aircraft surfaces.
Freezing conditions are conditions in which the outside air temperature is below +3C (37.4F) and visible
moisture in any form (such as fog with visibility below 1.5 km, rain, snow, sleet or ice crystals) or standing
water, slush, ice or snow is present on the runway.
Freezing fog (Metar code: FZFG) is a suspension of numerous tiny supercooled water droplets which freeze
upon impact with ground or other exposed objects, generally reducing the horizontal visibility at the earths
surface to less than 1 km (5/8 mile).
Freezing drizzle (Metar code: FZDZ) is a fairly uniform precipitation composed exclusively of fine drops diameter less
than 0.5 mm (0.02 inch) very close together which freeze upon impact with the ground or other objects.
Freezing rain (Metar code: FZRA) is a precipitation of liquid water particles which freeze upon impact with
the ground or other exposed objects, either in the form of drops of more than 0.5 mm (0.02 inch) diameter
or smaller drops which, in contrast to drizzle, are widely separated.
Friction coefficient is the relationship between the friction force acting on the wheel and the normal force on
the wheel. The normal force depends on the weight of the aircraft and the lift of the wings.
Frost is a deposit of ice crystals that form from ice-saturated air at temperatures below 0C (32F) by direct
sublimation on the ground or other exposed objects. Hoar frost (a rough white deposit of crystalline appearance
formed at temperatures below freezing point) usually occurs on exposed surfaces on a cold and cloudless
night. It frequently melts after sunrise; if it does not, an approved de-icing fluid should be applied in sufficient
quantities to remove the deposit. Generally, brushing alone cannot clear hoar frost. Thin hoar frost is a uniform
white deposit of fine crystalline texture, which is thin enough to distinguish surface features underneath, such
as paint lines, markings, or lettering.
Glaze ice or rain ice is a smooth coating of clear ice formed when the temperature is below freezing and freezing
rain contacts a solid surface. It can only be removed by de-icing fluid; hard or sharp tools should not be used to
scrape or chip the ice off as this can result in damage to the aircraft.
Grooved runway: see dry runway.
Ground visibility: The visibility at an aerodrome, as reported by an accredited observer.
Hail (Metar code: GR) is a precipitation of small balls or pieces of ice, with a diameter ranging from 5 to
50 mm (0.2 to 2.0 inches), falling either separately or agglomerated.
Holdover time is the estimated time anti-icing fluid will prevent the formation of frost or ice and the accumu-
lation of snow on the protected surfaces of an aircraft, under (average) weather conditions mentioned in the
guidelines for holdover time. The ISO/SAE specification states that the start of the holdover time is from the
beginning of the anti-icing treatment.
Ice Pellets (Metar code PE) is a precipitation of transparent (sleet or grains of ice) or translucent (small hail)
pellets of ice, which are spherical or irregular, and which have a diameter of 5 mm (0.2 inch) or less. The
pellets of ice usually bounce when hitting hard ground.
Icing conditions may be expected when the OAT (on the ground and for takeoff) is at or below 5C or
when TAT (in flight) is at or below 7C, and there is visible moisture in the air (such as clouds, fog with low
visibility of one mile or less, rain, snow, sleet, ice crystals) or standing water, slush, ice or snow is present
on the taxiways or runways.
Icy runway: A runway is considered icy when its friction coefficient is 0.05 or below.
Appendices
Appendices 69
Light freezing rain is a precipitation of liquid water particles which freezes upon impact with exposed objects,
in the form of drops of more than 0.5 mm (0.02 inch) which, in contrast to drizzle, are widely separated.
Measured intensity of liquid water particles are up to 2.5 mm/hour (0.10 inch/hour) or 25 grams/dm
2
/hour with
a maximum of 2.5 mm (0.10 inch) in 6 minutes.
Non-Newtonian fluids have characteristics that are dependent upon an applied force. The viscosity of Newtonian
fluids depends on temperature only.
NOTAM is a notice containing information concerning the establishment, condition or change in any aeronau-
tical facility, service, procedure or hazard, the timely knowledge of which is essential to personnel concerned
with flight operations.
One-step de-/anti-icing is carried out with an anti-icing fluid, typically heated. The fluid used to de-ice the
aircraft remains on aircraft surfaces to provide limited anti-ice capability.
Precipitation: Liquid or frozen water that falls from clouds as rain, drizzle, snow, hail, or sleet.
Continuous: Intensity changes gradually.
Intermittent: Intensity changes gradually, but precipitation stops and starts at least once within the hour
preceding the observation.
Precipitation intensity is an indication of the amount of precipitation falling at the time of observation. It
is expressed as light, moderate or heavy. Each intensity is defined with respect to the type of precipitation
occurring, based either on rate of fall for rain and ice pellets or visibility for snow and drizzle. The rate of fall
criteria is based on time and does not accurately describe the intensity at the time of observation.
Rain (Metar code: RA) is a precipitation of liquid water particles either in the form of drops of more than
0.5 mm (0.02 inch) diameter or of smaller widely scattered drops.
Rime (a rough white covering of ice deposited from fog at temperature below freezing). As the fog usually
consists of super-cooled water drops, which only solidify on contact with a solid object, rime may form only
on the windward side or edges and not on the surfaces. It can generally be removed by brushing, but when
surfaces, as well as edges, are covered it will be necessary to use an approved de-icing fluid.
Saturation is the maximum amount of water vapor allowable in the air. It is about 0.5 g/m
3
at 30 C and
5 g/m
3
at 0 C for moderate altitudes.
Shear force is a force applied laterally on an anti-icing fluid. When applied to a Type II or IV fluid, the shear
force will reduce the viscosity of the fluid; when the shear force is no longer applied, the anti-icing fluid should
recover its viscosity. For instance, shear forces are applied whenever the fluid is pumped, forced through
an orifice or when subjected to airflow. If excessive shear force is applied, the thickener system could be
permanently degraded and the anti-icing fluid viscosity may not recover and may be at an unacceptable level.
SIGMET is an information issued by a meteorological watch office concerning the occurrence, or expected
occurrence, of specified en-route weather phenomena, which may affect the safety of aircraft operations.
Sleet is a precipitation in the form of a mixture of rain and snow. For operation in light sleet treat as light
freezing rain.
Slush is water saturated with snow, which spatters when stepping firmly on it. It is encountered at tempera-
ture around 5C.
Snow (Metar code SN): Precipitation of ice crystals, most of which are branched, starshaped, or mixed without
branched crystals. At temperatures higher than about 5 C (23 F), the crystals are generally agglomerated
into snowflakes.
Dry snow: Snow which can be blown if loose or, if compacted by hand, will fall apart upon release; specific
gravity: up to but not including 0.35.
Dry snow is normally experienced when temperature is below freezing and can be brushed off easily from
the aircraft.
Appendices 70
Wet snow: Snow which, if compacted by hand, will stick together and tend to or form a snowball. Specific
gravity: 0.35 up to but not including 0.5. Wet snow is normally experienced when temperature is above
freezing and is more difficult to remove from the aircraft structure than dry snow being sufficiently wet to
adhere.
Compacted snow: Snow which has been compressed into a solid mass that resists further compression
and will hold together or break up into chunks if picked up. Specific gravity: 0.5 and over.
Snow grains (Metar code: SG) is a precipitation of very small white and opaque grains of ice. These grains
are fairly flat or elongated. Their diameter is less than 1 mm (0.04 inch). When the grains hit hard ground,
they do not bounce or shatter.
Snow pellets (Metar code: GS) is a precipitation of white and opaque grains of ice. These grains are spherical
or sometimes conical. Their diameter is about 2 to 5 mm (0.1 to 0.2 inch). Grains are brittle, easily crushed;
they bounce and break on hard ground.
Supercooled water droplets is a condition where water remains liquid at negative Celsius temperature.
Supercooled drops and droplets are thermodynamically unstable and freeze upon impact.
Two-step de-icing/anti-icing consists of two distinct steps. The first step (de-icing) is followed by the second
step (anti-icing) as a separate fluid application. After de-icing a separate overspray of anti-icing fluid is applied
to protect the relevant surfaces, thus providing maximum possible anti-ice capability.
Visibility: The ability, as determined by atmospheric conditions and expressed in units of distance, to see and
identify prominent unlit objects by day and prominent lit objects by night.
Visible moisture: Fog, rain, snow, sleet, high humidity (condensation on surfaces), ice crystals or when taxi-
ways and/or runways are contaminated by water, slush or snow.
Visual meteorological conditions: Meteorological conditions expressed in terms of visibility, distance from
cloud, and ceiling, equal to or better than specified minimums.
Wet runway: A runway is considered wet when the runway surface is covered with water, or equivalent,
less than or equal to 3 mm or when there is sufficient moisture on the runway surface to cause it to appear
reflective, but without significant areas of standing water.
Appendices
Appendices 71
Appendix 3. Abbreviations
AEA Association of European Airlines
AFM Airplane Flight Manual
AGL Above Ground Level
AOA Angle of Attack
APM Aircraft Performance Monitoring
ASD Accelerate-Stop Distance
ATC Air Traffic Control
Clouds As: Altostratus, Ns: Nimbostratus, Sc: Stratocumulus, St: Stratus, Ac: Altocumulus,
Cu: Cumulus, Cb: Cumulonimbus
FAA Federal Aviation Administration
FCOM Flight Crew Operating Manual
ICAO International Civil Aviation Organization
ISO International Standard Organization
MPC Multi Purpose Computer
NOTAM Notice To Airmen
OAT Outside Air Temperature
QRH Quick Reference Handbook
SAT Static Air Temperature
TAT Total Air Temperature
TOD Take-Off Distance
TOR Take-off Run
TOW Take-Off Weight
UTC Coordinated Universal Time
ATC March 2011
All reasonable care has been taken by ATC to ensure the accuracy of the present document.
However this document does not constitute any contractual commitment from the part of ATC which will offer,
on request, any further information on the content of this brochure. Information in this brochure is the property of ATC
and will be treated as confidential. No use or reproduction or release to a third part may be made there
of other than as expressely authorized by ATC.
ATR Customer Services - March 2011
Avions de Transport Rgional. 1, alle Pierre-Nadot 31712 Blagnac Cedex - France
Phone: +33 (0)5 62 21 62 07 - Fax: +33 (0)5 62 21 63 67 - https://www.atractive.com
Cont ac t
For ordering manuals, please contact us at:
Phone: +33 (0)5 6221 6207
e-mail: [email protected]
ATR Customer Services Portal: https://www.atractive.com

Coldweatheroperations 2011 20

Uploaded by

Copyright:

Available Formats

Coldweatheroperations 2011 20

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Coldweatheroperations 2011 20

Uploaded by

Copyright:

Available Formats

ATR CUSTOMER SERVICES

You might also like