c

Torque
Converter
CLARK-HURTI-:>
COMPONENTS
SM-C270 (Rev. 2-97)
I
I
I
I
I
I
I
TOWING OR PUSH STARTING
Before towing the vehicle, be sure to lift the
rear wheels off the ground or disconnect the
driveline to avoid damage to the trans-
mission during towing.
NOTE: If the transmission has 4 wheel drive,
disconnect both front and rear drivelines.
Because of the design of the hydraulic
system, the engine cannot be started by
pushing or towing.
OCopyright Clark Equipment Company, 1997
Unpublished material -All rights reserved
Limited Distribu1ion
No part of this work may be reproduced in any form under
any means withou1 direct written permission of Clark
Equipment Company.
FOREWORD
This manual has been prepared to provide the customer and the
maintenance personnel with information and instructions on the mainten-
ance and repair of the CLARK-HURTH COMPONENTS product.
Extreme care has been exercised in the design, selection of materials and
manufacturing of these units. The slight outlay in personal attention and
cost required to provide regular and proper lubrication, inspection at
stated intervals, and such adjustments as may be indicated will be
reimbursed many times in low cost operation and trouble free service.
In order to become familiar with the various parts of the product, its
principal of operation, trouble shooting and adjustments, it is urged that
the mechanic study the instructions in this manual carefully and use it as a
reference when performing maintenance and repair operations.
Whenever repair or replacement of component parts is required, only Clark-
Hurth Components-approved parts as listed in the applicable parts
manual should be used. Use of "will-fit" or non-approved parts may
endanger proper operation and performance of the equipment. Clark-
Hurth Components does not warrant repair or replacement parts, nor
failures resulting from the use of parts which are not supplied by or
approved by Clark-Hurth Components. IMPORTANT: Always furnish the
Distributor with the serial and model number when ordering parts.
TABLE OF CONTENTS
SECTIONAL VIEWS AND PARTS IDENTIFICATION
Torque Converter with Offset Output
A
Torque Converter with Inline Output
.c
CONVERTER OIL FLOW DIAGRAM
.E
IRREGULARITIES IN PERFORMANCE , F-G
GENERAL INFORMATION
, G
TRANSMISSION ClUTCH Oil PRESSURE
.G
OIL PRESSURE AND LUBRICATION RECOMMENDATIONS
.H
CONVERTER ASSEMBLY INSTRUCTIONS (Inline and Offset Output)
DISASSEMBLY OF TORQUE CONVERTER
, 1
CLEANING AND INSPECTION
...6
REASSEMBLY OF TORQUE CONVERTER
.7
RING GEAR INSTALLATION PROCEDURE (16 screw) for lockwire procedure. ..
.13
RING GEAR INSTALLATION PROCEDURE (32 Screw) , 14
CONVERTER ASSEMBLY INSTRUCTIONS (Lock-Up)
,..15
Torque Converter with Offset Output (Lock-Up) , 16
DISASSEMBLYOF LOCK-UP.
18
REASSEMBLY OF LOCK-UP
.20
AUTOMATIC LOCK-UP ADAPTOR DISASSEMBLY AND REASSEMBLY
.22
SPECIAL APPLICATION IMPELLER HUB BEARING .23
RING GEAR INSTALLATION PROCEDURE (16 Screw) , ...24
SPEED SENSOR INSTALLATION
26
DRIVE PLATE INSTALLATION INSTRUCTIONS ""... , 27
NOTE: Metric Dimensions Shown in Brackets
1.
SERVICING MACHINE AFTER TORQUE CONVERTER OVERHAUL
The transmission, torque converter, and its allied
hydraulic system are important links in the drive line
between the engine and the wheels. The proper oper-
ation of either unit depends greatly on the condition
and operation of the other; therefore, whenever repair
or overhaul of one unit is performed, the balance of
the system must be considered before the job can be
considered completed.
5. On remote mounted torque converters remove
drain plug from torque converter and inspect
interior of converter housing, gears, etc. If
presence of considerable foreign material is
noted, it will be necessary that converter be re-
moved, disassembled and cleaned thoroughly.
It is realized this entails extra labor; however ,
such labor is a minor cost compared to cost of
difficulties which can result from presence of
such foreign material in the system.
6,
After the overhauled or repaired transmission has
been installed in the machine, the oil cooler, and con-
necting hydraulic system must be thoroughly cleaned.
This can be accomplished in several manners and a de-
gree of judgment must be exercised as to the method
employed.
The following are considered the minimum steps to
be taken:
Drain entire system thoroughly.
2. Disconnect and clean all hydraulic lines. Where
feasible, hydraulic lines should be removed from
machine for cleaning.
3. Replace oil filter elements, cleaning out filter
cases thoroughly.
4. The oil cooler must be thoroughly cleaned. The
cooler should be "back flushed" with oil and
compressed air until all foreign material has been
removed. Flushing in direction of normal oil flow
will not adequately clean the cooler. If neces-
sary, cooler assembly should be removed from
machine for cleaning, using oil, compressed air
and steam cleaner for that purpose. DO NOT
use flushing compounds for cleaning purposes.
Reassemble all components and use only type
oil recommended in lubrication section. Fill
transmission through filler opening until fluid
comes up to LOW mark on transmission dipstick.
NOTE: If the dipstick is not accessible oil level
check plugs are provided.
Remove LOWER check plug, fill until oil runs
from LOWER oil hole. Replace filler and level
plug.
Run engine two minutes at 500-600 RPM to
prime torque converter and hydraulic lines. Re-
check level of fluid in transmission with engine
running at idle (500-600 RPM).
Add quantity necessary to bring fluid level
to LOW mark on dipstick or runs freely from
LOWER oil level check plug hole. Install oil
level plug or dipstick. Recheck with hot oil
(180-200 F.) [82, 2-93, 3 C].
Bring oil level to FULL mark on dipstick or
runs freely from UPPER oil level plug.
7. Recheck all drain plugs, lines, connections, etc.,
for leaks and tighten where necessary.
CONVERTER CHARGE PUMP REPLACEMENT AND PRIMING PROCEDURE
1. The cause for pump failure must be found and corrected before a replacement pump is installed. Check all of the hoses,
tubes, "0" rings, adaptors and split flanges.
2. Replace any collapsed or damaged hoses, damaged split flange "0" rings, tube "0" rings and adaptors.
3. After all checks have been made and corrections completed install the pump.
4. See filling instructions in paragraph 6 above.
5. Start the engine. Run the engine at low idle for two minutes, watch the clutch pressure gage and listen for cavitation of
the pump.
6. If the pressure does not come up, check the oil level and bleed off air from system as follows.
7. To bleed off the air from the system, loosen the pressure gage line at the pressure regulating valve or loosen the pressure
hose at the oil filter or pressure regulating valve. Crank the engine over until the air is displaced with oil. DO NOT START
THE ENGINE.
8. If bleeding the lines does not correct the problem it may become necessary to prime the pump. Disconnect the suction
hose or pressure hose, whichever is higher, and fill the port with transmission oil, reconnect the hose and tighten.
9. Start the engine and check pressure.
10. Recheck oil level with hot oil (180-200F) with engine at idle. Add oil as necessary to bring oil level to full mark.
12~
~
I
I
~
/"Y
4t"'\
5251
\
26-~
'\
\
\
"0
~
\is
59
\
/
\-/
.~.
\ /
\
/
...\
/
/
\
/
\
/
/
.,~
\,
""'/
\
/
1t
/
/
/
," /
/
/
7~
I /
76
~\
)778
...',
"
/ --.::-
/
--"'\
i,/"',
~///
I
/
/
\
/
\
/
/
~
/
/
/
\,
/
/
/
-A
/
/
/
/
/
\
/
/
/
'~II
104
/
11
\~/
Figure A
24-'
/
C-270 CONVERTER WITH OFFSET OUTPUT
ITEM DESCRIPTION QTY. ITEM DESCRIPTION QTY.
I
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
III
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
Inlet Cover (3000 Trans. only) ,
Inlet Cover Plug (3000 Trans. only) 1
Cover Bolt Lockwasher (3000 Trans. only) 1
Cover Bolt-Long (3000 Trans. only) ,
Cover Bolt-Short (3000 Trans. only) 3
Cover Bolt Lockwasher (3000 Trans. only) 3
Valve Stop ,
Valve Stop "0" Ring 1
Valve Piston ,
Valve Spring -Inner ,
Valve Spring -Outer ,
Valve Stop Roll Pin ,
Regulator Valve to Housing Screw Lockwasher 4
Regulator Valve to Housing Screw 4
Valve Stop Roll Pin 1
Valve Stop "0" Ring 1
Valve Stop 1
Regulating Valve Assembly 1
Valve Housing Pipe Plug 1
Valve Housing Pipe Plug 1
Safety Valve Seat 1
Safety Valve Plunger 1
Safety Valve Spring ,
Regulator Valve to Housing "0" Ring 1
Regulator Valve to Housing Gasket ,
Air Breather Check Valve Assembly 1
Pump Drive Gear 3
Pump Drive Gear Snap Ring 3
Converter Housing 1
Converter Housing Pipe Plug 1
Oil Baffle Screw Lockwasher 3
Oil Baffle Screw 3
Converter Housing Pipe Plug 1
Converter Housing Pipe Plug 2
Pump Drive Shaft Bearing 3
Pump Drive Shaft Spacer 3
Pump Drive Shaft Bearing 3
Bearing Locating Ring 3
Pump Drive Shaft 3
Pump Drive Shaft Snap Ring 3
Pump Shaft Washer 3
Pump Shaft Snap Ring 3
Charging Pump Sleeve 1
Pump Gasket 1
Pump Mounting Screw Lockwasher 3
Pump Mounting Screw 3
Converter Charging Pump 1
Output Shaft Nut 1
Output Shaft Washer 1
Output Shaft "0" Ring 1
Bearing Retainer Screw 3
Bearing Retainer Screw Lockwasher 3
Companion Flange 1
Bearing Retainer Oil SeaL ,
Bearing Retainer Stud Nut 2
Bearing Retainer Stud Lockwasher 2
Bearing Retainer 1
Output Shaft Bearing Retainer Stud 2
Bearing Retainer "a" Ring 2
Output Shaft Rear Bearing 1
Output Shaft Bearing Snap Ring 1
Output Shaft 1
Output Shaft Gear ,
Output Shaft Front Bearing 1
Bearing Snap Ring 1
Output Gear Snap Ring 1
Turbine Shaft Gear 1
Turbine Shaft Snap Ring 1
Turbine Shaft Bearing 1
Turbine Shaft Piston Ring 1
Turbine Shaft 1
Stator Support & Sleeve Assembly 1
p. t R.
E d S ."'0 Longer Used
IS on Ing xpan er prong L'
Stator Support Piston Ring 1
Impeller Hub Gear Snap Ring 1
Impeller Hub Gear 1
Stator Support Screw 6
Stator Support Screw Lockwasher 6
Turbine 1
Turbine Hub 1
Turbine Shaft Snap Ring 1
Reaction Member Snap Ring 1
Reaction Member 1
Reaction Member Spacer 1
Impeller Bearing Snap Ring 1
Impeller Hub Bearing 1
Impeller Hub 1
Impeller Hub "0" Ring 1
Impeller c 1
Hub to Impeller Screw Washer 8
Hub to Impeller Screw 8
Oil Baffle 1
Oil Baffle "0" Ring 1
Oil Baffle Oil Seal 1
Impeller to Cover "0" Ring 1
Impeller Cover Bearing Snap Ring 1
Impeller Cover Bearing 1
Impeller Cover 1
Impeller Cover Sleeve 1
Ring Gear Screw 16
Plain Washer 16
Flywheel Ring Gear 1
Turbine Shaft Snap Ring 1
Turbine Hub Screw Lockwasher 8
Turbine Hub Screw 8
Impeller to Cover Screw Lockwasher 24
Impeller to Cover Screw 24
Pump Adaptor Gasket 1
Pump Adaptor 1
Pump Adaptor Screw Lockwasher 2
Pump Adaptor Screw 2
Pump Adaptor Screw Lockwasher 3
Pump Adaptor Screw 3
Pump Adaptor Gasket 1
Pump Adaptor 1
Pump Adaptor Screw 6
Pump Adaptor Stud Nut 4
Pump Adaptor Stud Lockwasher 4
Pump Adaptor Stud 4
Idler Shaft Snap Ring " 1
Idler Shaft Drive Gear 1
Idler Shaft Bearing 1
Governor Drive Gear 1
Idler Shaft Bearing 1
Idler Shaft '-0" Ring 1
Idler Shaft 1
Idler Shaft Key 1
Pump Stud 6
Charging Scavenger Pump (Optional) 1
Pump Stud Lockwasher 6
Pump Stud Nut 6
-8-
C-210 CONVERTER WITH INLINE OUTPUT
ITEM DESCRIPTION QTY. ITEM DESCRIPTION QTY.
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
-D-
IRREGULARITIES IN PERFORMANCE
C-270 Series Converters
Make all checks with converter outlet temperature at least 180 -200 F. [82,3 -93,3 C.]
PROBABLE CAUSE REMEDY
TROUBLE
Worn oil sealing and
"0" rings
A. Trouble is internal and will require a corn.
plete tear-down of the converter .
1 .Low converter
(Below 25 p .S.
with engine at
NO LOAD)
(See Converter
Specifications)
B. Replace.
C. Clean and check valve spring and valve.
Worn oil pump.
Safety Valve stays open.
2. Sucfion line faking air. D. Fill to proper level.
E. Check oil line connections and tighten
securely.
F. Replace.
low oil level.
Suction line connection!
taking air .
Worn oil pump.
G. Check oil cooler line and oil cooler for
restrictions. Clean or replace.
Oil cooler or oil lineo;
restricted.
H. Check oil weight. See oil recommenda-
tions.
I. Converter pressure in cold weather will
vary. As soon as converter gets hot, pres-
sure should drop.
Oil too heavy
3. High converter
(Above 70 P.S.
with engine at
NO LOAD)
(See Converter
Specifications)
Cold oil.
4. Over-heating
J. Clean and check oil cooler and oil cooler
lines. Replace if necessary.
K. Replace with larger cooler.
l. Replace oil pump.
M. Install at lowest drain opening in conver-
ter housing. line must maintain constant
gradual drop to oil sump for gravity drain.
See items No. 1 & 2.
Oil cooler or oil cooler
lines restricted causing
safety valve to stay open.
Oil cooler too small.
Worn oil pump
Converter drain line to
transmission or oil sump
not installed properly.
Worn cou
Worn oil
Damaged
5. Noisy Converter. N. Replace.
0. Replace.
P. A complete teardown will be necessary
to determine this. Replace if necessary.
Q. Replace. Worn drive gears.
Transmission malfunc-
tion.
6. low clutch pressure.
(See pressure specifications)
R. Close pressure line to transmission con-
trol valve. If clutch pressure returns to
normal, trouble is in transmission.
S. Replace.
T. Clean and check valve for worn or dirty
parts, replace if necessary.
Worn oil pump.
Regulator valve stuck
open.
~-
OUT pressure
I. [172,4 kPa]
2000 RPM -
Pressure
OUT pressure
I. [482,6 kPa]
2000 RPM -
Pressure
piing gear .
pump
bearing.
IRREGULARITIES IN PERFORMANCE (Cont'd.)
C-270 Series Converters
TROUBLE PROBABLE CAUSE REMEDY
Regulator valve stuck
closed.
u. See item T. 7. High clutch pressure.
(See pressure specifications)
8. Lack of power. v. Tune engine
Check governor. w. Tune engine.
x. See item No.
Improper engine func-
tion.
Engine stall speed below
normal.
low converter out pres-
sure.
Air in the oil.
Improper oil.
v. See item No.2.
Z. See oil recommendations.
9. Oil in engine flywheel
housing.
AA. Replace.
88. Replace.
"011 ring between impel-
ler cover and impeller
damaged.
Oil baffle "011 ring
damaged.
Oil baffle oil seal
damaged.
cc. Replace.
I
GENERAL INFORMATION:
Use Clark 1533614 Oil Filter only.
Use Clark 215502 Oil Filter Element only.
Use minimum number of Pipe and Hose Fittings.
Gravity drain from Converter Sump to Transmission mlJst be of minimum length and have no "U" bends to trap air or
oil.
Cooler capacity for normal application, 30 per cent of net Engine Horsepower at Governed Speed.
Check oil level with engine idling and transmission in neutral.
CHANGE OIL FILTER ELEMENT EVERY 500 HOURS. DRAIN AND REFILL SYSTEM EVERY 1000 HOURS.
I
I
TRANSMISSION CLUTCH OIL PRESSURE P.S.I.
The C-270 Converter will be equipped with one of three variations involving the clutch regulating valve. They are as follows:
1.lnlet cover for Converter oil only with clutch pressure valve in transmission control cover. 180 to 220 P.S.I. [1241.1 -1516.8
kPa] pressure range. (See note).
2. Pressure regulator valve on Converter with a 240 to 280 P.S.I. [1654.8- 1930.5 kPa] pressure range. (See Note).
3. Pressure regulator valve on Converter with a 180 to 220 P.S.I."i1.241.1 -1516.8 kPa] pressure range. (See Note).
NOTE: All pressure must be equal within 5 P.S.I. [34.5 kPa]. If clutch pressure varies in anyone clutch more than 5 P.S.I. [34.5 kPa]
repair clutch. All pressures must be taken with two clutches engaged.
I
.
-G-
OIL PRESSURE AND LUBRICATION SPECIFICATIONS
for C-270 SERIES CONVERTERS
Converter outlet oil temperature 1800 -200 F. [32,3 -93.3 C],
Transmission in NEUTRAL.
Converter Out
Pressure
Operating specifications:
25 P.S.I. [172,4 kPa] minimum pressure at 2000 RPM engine speed AND a maximum of 70 P.S.I. [482,6
kPa] outlet pressure with engine operating at no-load governed speed.
Converter outlet presssure equals the total pressure drop of the cooler, cooler lines and back pressure of the tranmsmis-
sion lubrication systems.
Disconnect CONVERTER DRAIN BACK line at transmission with engine running at 2000 RPM and
measure oil into a gallon container. Measure oil leakage for 15 seconds and multiply the volume of oil by
four to get gallons per minute leakage.
Converter Lube Flow
Leakage in C-270 series not to exceed 2 gallons maximum per minute. Leakage in Converter
LUBRICA TION
TYPE OF OIL See Lube Chart.
CAPACITY Consult Operator's Manual on applicable
machine model for system capacity. Torque
Converter, Transmission and allied hydraulic
system must be considered as a whole to
determine capacity.
CHECK PERIOD Check oil level DAILY with engine running
at 500.600 RPM and oil at 180 to 200 F.
[82, 2.93, 3 C]. Maintain oil level to FULL
mark.
NORMAL * Every 500 hours, change oil filter element.
DRAIN PERIOD Every 1000 hours, drain and refill system as
follows: Drain with oil at 150 to 200 F.
[65,6-93,3 C].
NOTE: It is recommended that filter elements
be chang"d after 50 and 100 hours of op-
eration on new and rebuilt or repaired units.
(a) Drain transmission and remove sump
screen. Clean screen thoroughly and
reploce, using new goskets.
(b) Droin oil filters, remove and discord
filter elements. Clean filter shells ond
instoll new elements.
(c) Refill tronsmission to LOW ma!k.
(d) Run engine at 500-600 RPM to prime
converter ond lines.
(e) Recheck level with engine running ot
500 -600 RPM ond add oil to bring
level to LOW mork. When oil tempero-
ture is hot (180-200 F.) [82,2-93,3 C]
moke final oil level check. BRING OIL
LEVEL TO FULL MARK.
* Normal drain periods and filter change intervals are for average environmental and duty-cycle conditions.
Severe or sustained high operating temperatures or very dusty atmospheric conditions will cause acceler-
ated deterioration and contamination. For extreme conditions judgment must be used to determine the
required change intervals.
-H-
7. AFTER ASSEMBLY OF PARTS USING
PERMATEX OR CRANE SEALER
THERE MUST BE NO FREE OR
EXCESS MATERIAL THAT COULD
ENTER THE OIL CIRCUIT
B. HEAT NOSE BUSHING TO 200 F.
{93 C] BEFORE ASSEMBLY OF
BUSHING TO COVER.
9. GOVERNOR DRIVE NEEDLE BEAR-
INGS TO BE PRESSED 0.031 [0.79]
BELOW ENDS OF GEAR
10 LUBE HOLES TO BE CHECKED
PRIOR TO ASSEMBLY. HOLES MUST
BE FREE OF DIRT & BURRS.
1. TORQUE OUTPUT SHAFT NUT TO
200-250 Ib.ft [271,2-338.9 N.m.1
2. ALL LEAD-IN CHAMFERS FOR OIL
SEALS, PISTON RINGS & "0"
RINGS MUST BE SMOOTH & FREE
FROM BURRS. INSPECT AT
ASSEMBLY
3. LUBRICATE ALL PISTON RINGS &
"0" RINGS AT ASSEMBLY
4. APPLY THIN COATING OF GREASE
BETWEEN SEAL LIPS ON LIP TYPE
SEALS PRIOR TO ASSEMBLY.
5. USE PERMATEX & CRANE SEALER
ONLY WHERE SPECIFIED.
6. APPLY VERY LIGHT COAT OF
PERMATEX NO.2 TO O.D OF ALL
OIL SEALS BEFORE ASSEMBLY
REGULATOR VALVE
LOCKWIRE
Q
11
7~
'=-;
Y::
~
,31 [7,9]-J -
/
.:r
)::::11
"'
1[
J ~,--;"","
~ ~ ENLARGED VIEW OF
PISTON RING &
.EXPANDER
J m
56 [ 14, 2]
1
~
5
:1
~
...;-..,./
~
-(-"j]]
-~\
I
LUBE HOLES TO BE CHECKED
/ PRIOR TO ASSEMBL y .HOLES
MUST BE FREE OF DIRT
&BURRS.
'PERMATEX 2 STUDS USED ON
REAR BEARING CAP.
STRAIGHT THRU DRIVE
~~
OFFSET DRIVE
'\
SEAL TO BE FLUSH
WITH REAR SURFACE
NOTE: METRIC OIMENSIONS
SHOWN IN BRACKETS
"L.--
Torque Specification for Lubricated
or Plated Screw Threads
NOM.
SIZE
.7500
flNE THREAD
Le-fT ,N'm]
COARSE THREAD
LB-FT [N'm]
r 10.9 -
FINE THREAD
LB-FT-IN'm]
COARSE THREAD
LB.FT (N"ml
9- 11
16- 20
26- 29
41- 45
64- 70
91- ~oo
128- 141
223 -245
[ 12,3; 14,9]
[ 21,7- 27, 1]
[ 35,3 -39,3]
[ 55,6 -61,0]
I 86,8 -94,9]
[123,4- 135,5]
[173,5 -191,2]
(~02,3 -332,2)
8- 10
12- 16
23- 25
37- 41
57- 63
82- 90
113- 124
200 -220
.13,51
[ 16,3 -21,61
[ 31,2 .33,8]
[ 50,2 .55,5]
[ 77,3 -85,4]
[111,2.122,01
[153,2.168,1]
[271,2- 298,31
11- 13
28- 32
37- 41
58- 64
90- 99
128- 141
180.198
315- 347
ASSEMBLY INSTRUCTIONS FOR C-270 CONVERTER
WITH INLINE AND OFFSET OUTPUT
LMUST BE LOOSE INTERNAL
FIT BEARING. NO. "3" ETCHED
ON BEARING.
'TORQUE TURBINE BOL TS
TO 30-35 LBS./Ft. [40.7-47 ,4 N.m.]
I
C-270 SERIES CONVERTER
The following instructions will cover the disassembly
and assembly of the C-270 Converter in a sequence that
would normally be followed after the Converter has
been removed from the vehicle.
CAUTION: Cleanliness is of extreme importance and
an absolute must in the repair and overhaul of the
Converter. Before attempting any repairs the exterior
of the unit must be thoroughly cleaned to prevent the
possibility of dirt and foreign matter entering the
mechanism.
DISASSEMBLY
Figure 3
If pilot bushing sleeve is to be replaced use proce-
dure as shown above.
Figure 1
Remove bolts securing impeller cover to impeller.
Figure 4
If necessary to replace pilot bearing, remove retain-
er ring and use small inside bearing puller.
Figure 2
Use two bolts in threaded puller holes 180 apart to
remove impeller cover from impeller. NOTE: some
units may have pry slots instead of threaded holes.
Figure 5
Remove outer turbine hub retainer ring.
-1-
I
I
I
I
I
Figure 9
Reaction member and spacer .
I
Figure 6
Remove turbine and hub assembly frol'r1 turbine
shaft. Remove turbine locating ring.
I
Figure 10
Remove three bolts that secure oil baffle to con-
verter housing.
I
Figure 7
Remove reaction member retainer ring.
I
Figure 11
Install special puller tool as shown above, turn jack
screw pulling oil baffle and impeller from stator support
as an assembly. Special tool can be made for easier
removal of impeller assembly but it is not necessary.
(See Figure 12).
Figure 8
Remove reaction member from stator support
threaded puller holes are provided should reaction
member be too tight to be removed by hand.
-2-
I
I
Figure 12
If special tool is not available, remove oil baffle bolts
part way. Tap lightly on each bolt, this will loosen oil
baffle from converter housing, remove oil baffle and
impeller from housing as an assembly.
Figure 15
Remove oil baffle oil seal and "0" ring. NOTE: Oil
seal should be removed only if it is to be replaced.
Figure 13
Remove impeller hub gear retainer ring.
Figure 16
Remove impeller hub bolts and washers.
Figure 17
Remove impeller hub from impeller. Remove hub
"0" ring.
Figure 14
Remove impeller hub gear and oil baffle from impeller.
-3-
Figure 21
On offset output, remove stator support and turbine
shaft assembly from converter housing.
Figure 18
Remove hub bearing retainer ring and press bearing
from hub.
Figure 19
PUMP DRIVES VARY IN QUANTITY FROM ONE TO
THREE -ALL DRIVES DISASSEMBLE THE SAME.
Remove oil pump drive gear retaining rings. Remove
drive gears from pump shafts.
Figure 22
On inline output, remove companion flange cotter,
nut, washer, \\0" ring, and companion flal:1ge from in-
line turbine shaft.
Figure 23
Remove inline turbine shaft by using a brass ham-
mer and tapping on threaded end of shaft. Stator sup-
port and turbine shaft will come out as a unit.
Figure 20
Remove stator support bolts.
-4-
(I
Figure 24
On offset output remove turbine shaft gear retainer
ring and turbine shaft gear .
Figure 27
On the inline output converter, the offset output shaft
cover need not be removed unless \\0" ring is to be
cnanged.
Figure 28
Remove pump adaptor sleeve from pump shaft.
Remove pump shaft washer retainer ring and pump
shaft washer .
Figure 25
Remove turbine shaft bearing retainer ring :Tram
stator support. NOTE: Use same procedure on 'in\ine
output or offset output.
Figure 26
Press turbine shaft from stator support. Press turbine
bearing from turbine shaft. Remove oil sealing rings
from stator support and turbine shaft. NOTE: Use same
procedure on inline output or offset output.
Figure 29
Tap on pump shaft from inside converter housing,
pump shaft and bearings will come out as an assembly.
-5-
CLEANING AND INSPECTION
I
CLEANING
Clean all parts thoroughly using solvent type clean-
ing fluid. It is recommended that parts be immersed
in cleaning fluid and moved up and down slowly until
all old lubricant and foreign material is dissolved and
parts are thoroughly cleaned.
CAUTION: Care should be exercised to avoid skin
rashes, fire hazards and inhalation of vapors when
using solvent type cleaners.
Bearings
Remove bearings from cleaning fluid and strike flat
against a block of wood to dislodge solidified particles
of lubricant. Immerse again in cleaning fluid to flush
out particles. Repeat above operation until bearings
are thoroughly clean. Dry bearings using moisture-
free compressed air. Be careful to direct air stream
across bearing to avoid spinning. Do not spin bearings
when drying. Bearings may be rotated slowly by hand
to facilitate drying process.
Figure 30
Remove pump shaft bearing locating ring.
bearings from pump shaft.
Press
Figure 31
Remove pressure regulator valve assembly. Use
caution as not to lose safety valve plunger or spring
(See arrow).
Housings
Clean interior and exterior of housings, bearing caps,
etc., thoroughly. Cast parts may be cleaned in hot
solution tanks with mild alkali solutions providing these
parts do not have ground or polished surfaces. Parts
should remain in solution long enough to be thorough-
ly cleaned and heated. This will aid the evaporation of
the cleaning solution and rinse water. Parts cleaned
in solution tanks must be thoroughly rinsed with clean
water to remove all traces of alkali. Cast parts may
also be cleaned with steam cleaner.
CAUTION: Care should be exercised to avoid in-
halation of vapors and skin rashes when using alkali
cleaners.
All parts cleaned must be thoroughly dried immedi.
ately by using moisture-free compressed air or soft,
iintless absorbent wiping rags free of abrasive materi-
als such as metal filings, contaminated oil or lapping
compound.
INSPECTION
The importance of careful and thorough inspection
of all parts cannot be overstressed. Replacement of
all parts showing indication of wear or stress will elim-
inate costly and avoidable failures at a later date.
Figure 32
Depress piston stop and remove piston stop roll pin.
Remove piston stop and inner and outer spring. Re-
move roll pin at opposite end. Remove valve stop and
valve piston.
-6-
I
11
Bearings:
Carefully inspect all rollers, cages and cups for wear,
chipping or nicks to determine fitne~s of bearings for
further use. Do not replace a bearing cone or cup
individually without replacing the mating cup or cone
at the same time. After inspection, dip bearings in
recommended type Automatic Transmission Fluid and
wrap in clean lintless cloth or paper to protect them
until installed.
REASSEMBL Y OF TORQUE CONVERTER
Instructions given below on reassembly of compo-
nents are given in the sequence that must be followed
in rebuilding.
Oil Seals, Gaskets, Etc.
Replacement of spring load oil seals, "0" rings,
metal sealing rings, gaskets and snap rings is more
economical when unit is disassembled than premature
overhaul to replace these parts at a future time. Fur-
ther loss of lubricant through a worn seal may result
in failure of other more expensive parts of the assem-
bly. Sealing members should be handled carefully,
particularly when being installed. Cutting, scratching,
or curling under of lip of seal seriously impairs its
efficiency. Apply a thin coat of Permatex No.2 on
the outer diameter of the oil seal to assure an oil tight
fit into the retainer. When assembling new metal type
sealing rings, same should be lubricated with coat of
chassis grease to stabilize rings in their grooves for
ease of assembly of mating members. lubricate all
"0" rings and seals with recon-:mended type Automatic
Transmission Fluid before assembly.
Figure 33
Install valve piston (top view Figure 33). Install
valve stop and new "0" ring in valve housing and
secure with roll pin. Install inner and outer valve
spring in valve housing. Install valve spring stop and
new "0" ring in valve housing. Depress spring stop
and install spring stop roll pin.
Gears and Shafts
If magna-flux process is available, use process to
check parts. Examine teeth on all gears carefully for
wear, pitting, chipping, nicks, cracks or scores. If gear
teeth show spots where case hardening is worn through
or cracked, replace with new gear. Small nicks may
be removed with suitable hone. Inspect shafts and
quills to make certain they are not sprung, bent, or
splines twisted, and that shafts are true.
Figure 34
Install pump shaft rear bearing locating ring. Press
rear bearing on pump shaft with bearing snap ring
toward rear of shaft. Install bearing spacer and press
front bearing on shaft until it shoulders against bear-
ing spacer.
Housing, Covers, etc.
Inspect housings, covers and bearing caps to be
certain they are thoroughly cleaned and that mating
surfaces, bearing bores, etc., are free from nicks or
burrs. Check all parts carefully for evidence of cracks
or condition which would cause subsequent oil leaks
or failures.
I
Figure 35
Install pump shaft and bearing assembly in conver-
ter housing.
-7-
I
I
I
Figure 39
Press output rear 'bearing in bearing retainer. Secure
with retainer ring. Press output shaft into bearing
retainer. Use caution as not to damage oil seal. Posi-
tion output gear on shaft. Press front output bearing
on shaft. Install bearing retainer ring.
Figure 36
Tap pump shaft and bearing assembl'l in converter
housing until rear bearing snap ring shou1ders against
bearing bore.
Figure 40
Press offset output shaft, gear and bearing assembly through
rear bearing and bearing retainer. Secure output shaft gear in
vise equipped with soft jaws. Install companion flange, new
flange "0" ring, flange washer and flange nut, tighten nut 200
to 250 foot pounds torque [271 ,2 -338,9 N.m.].
Figure 37
Install pump shaft washer and washer retainer ring.
Pump adaptor sleeve can be installed just before pump.
I
Figure 38
Apply a light coat of Permatex on the outer diameter
of the output shaft oil seal. Press oil seal in bearing
retainer from inside of retainer as shown and to di-
mension shown. Press inline output shaft oil seal in
converter housing. Lip of seal in. NOTE: Oil seal
must be pressed 5/16" [7,93 mm] below rear face
of converter housing.
Figure 41
Install new "0" ring (See arrow) on offset output
shaft bearing retainer. Install output shaft assembly to
converter housing and secure with nuts, bolts and lock-
washer. Tighten to specified torque.
-8-
~
Figure 45
Install new oil sealing ring on support.
Figure 42
Press rear bearing on turbine shaft, this is also the
output shaft for the inline output converter, install
shaft oil sealing ring (See arrow).
Figure 46
Install companion flange spacer on threaded end of
inline output shaft. NOTE: Spacer must be put on shaft
before shaft installation in converter housing, as spacer
will not pass through oil seal. Align holes in stator
support with holes in converter housing. Install bolts
and tighten to specified torque.
Figure 43
Press shaft and bearing assembly in stator support.
Use caution as not to damage oil sealing ring. Secure
bearing with retainer ring. Use same procedure on
inline output or offset output.
Figure 44
Install output shaft gear on offset output shaft and
secure with retainer ring.
Figure 47
Install oil pump drive gears and secure with retainer
rings.
-9-
I
I
I
I
Figure
NOTE: See page 23 for 13 inch special impeller
hub bearing and 12 bolt assembly instructions.
Install bolts and tighten to specified torque. lock-
wire in pairs to prevent loosening.
Figure 48
On inline output shaft install companion flange, new flange
"0" ring, flange washer and flange nut. Tighten nut 200 to 250
foot pounds torque [271 ,2 -338,9 N.m.l.
Install oil baffle on impeller assembly. Install im-
peller hub gear on impeller hub and secure with re-
tainer ring. Install new "0" ring on oil baffle (See
arrow).
Figure 49
Press new oil seal in oil baffle with lip of seal down.
(See Fig. I).
Figure 53
Install impeller and oil baffle assembly over stator
slJpport and into converter housing. Align holes in
oil baffle with holes in converter housing. Install
bolts and lockwashers into oil baffle. Tighten baffle
bolts evenly to prevent damaging oil baffle "0" ring.
Tighten to specified torque.
Figure SO
Press impeller bearing in impeller hub and secure
with retainer ring. Install new "0" ring (see arrow) on
impeller hub. Align holes in impeller hub with holes
in impeller.
-10-
I
il
Figure 54
Install reaction member spacer with tang of spacer out. Install
reaction member. NOTE: Casted knob on reaction member
must be positioned between the 3 & 6 o'clock location on
support, preferably between 4 & 5 o'clock.
Figure 57
Install turbine and hub assembly on turbine shaft
and secure with outer retaining ring.
I
Figure 58
Press pilot bearing in impeller cover and secure with
retainer ring.
Figure 55
Install reaction member on stator support and se-
cure with retaining ring.
Figure 59
Heat impeller cover sleeve to 2000 [93 C.] and press on im-
peller shaft.
Figure 56
Install inner turbine locating ring on turbine shaft.
-11-
Figure 60
Install spring and plunger in converter housing (See
arrow). Install new gasket on valve assembly. Install
pew "0" ring on valve assembly. Secure valve assem-
bly to converter housing with bolts and lockwashers.
Tighten to specified torque. Figure 62
Install impeller cover to impeller bolts and lock-
washers, tighten to specified torque.
Figure 61
Install new \\0" ring (See arrow) on impeller cover.
Align holes in impeller cover with holes in impeller.
.
I
I
SEE PAGE 26 FOR SPEED SENSOR INSTALLATION
I
-12-
I
I
16 SCREW STABLE DRIVE CONNECTION NON-ASBESTOS CONVERTER DRIVE
RING GEAR INSTALLATION PROCEDURE
)J
1 Remove all burrs from flywheel mounting face and pilot bores. Clean the torque converter ring gear flywheel
mounting surface and the ring gear screw tapped holes with solvent. Dry thoroughly, being certain ring gear
screw holes are dry and clean.
I
I
Check engine flywheel and housing or housing adaptor for conformance to standard S.A.E. No.3 -SAE
J927 and J1033 tolerance specifications for pilot bores size, pilot bores eccentricities and mounting face
deviations. Refer to CLARK-HURTH form number 802563 for measuring procedures.
2.
3. Measure and record engine crankshaft and end play.
Install torque converter ring gear as shown. 4.
NOTE: Assembly of the ring gear must be completed within a fifteen minute
period from start of screw installation. The screws are prepared with an epoxy
coating which begins to harden after installation in the flywheel mounting holes. If not
tightened to proper torque within the fifteen minute period insufficient screw clamping
tension will result.
I
5. Install backing ring and sixteen (16) special screws to approximately .06 inch [1.5 mm] of seated position. It is
permissible to use a power wrench for this installation phase. With a calibrated torque wrench tighten screws 38
to 42 pounds feet of torque [51,6- 56,9 N.m].
To obtain maximum effectiveness of the special screw's locking feature, a minimum time period after screw
installation of twelve (12) hours is suggested before engine start-up.
I
The special screw is to be used for ONE installation only. If the screw is removed for any reason it MUST BE
REPLACED. It is recommended that the epoxy left in the flywheel hole be removed with the proper tap and
cleaned with solvent. Dry hole thoroughly and use a NEW screw for re-installation.
6. Assemble torque converter to engine flywheel by sliding converter into position by hand before fastening hous-
ing attachment screws. This may require more than one trial to match the drive gear teeth. Pulling the convert-
er into position with housing attachment bolts is not recommended.
Measure engine crankshaft end play after assembly of torque converter. This value must be within one
thousandth (.001) of an inch [0,0254 mm] of end play recorded (line 3) before assembly of torque
converter.
802646 -1.5 INCH [38,1] 16 SCREW RING GEAR KIT
1 249474 SDC Torque Converter Ring Gear
16 236288 Ring Gear Screw 1.5 Inch [38,1]
1 802648 Installation Instruction Sheet
802647 -1.5 INCH [38, 1] 16 SCREW RING GEAR KIT
1 249474 SDC Torque Converter Ring Gear
16 236288 Ring Gear Screw 1.5 Inch [38.1]
1 243767 Backing Ring
1 802648 Installation Instruction Sheet
243767 Backing Ring not included in 802646 Ring Gear Kit. Must be Ordered Separately.
SEE PAGE 24 FOR 32 SCREW RING GEAR INSTALLATION PROCEDURE
-13-
I
I
I
-14-
7. AFTER ASSEMBLY OF PARTS USING
PERMATEX OR CRANE SEALER
THERE MUST BE NO FREE OR
EXCESS MATERIAL THAT COULO
ENTER THE OIL CIRCUIT
B. HEAT NOSE BUSHING TO 200 F.
[93 C) BEFORE ASSEMBLY OF
BUSHING TO COVER
9 GOVERNOR ORIVE NEEOLE BEAR-
INGsTOBEPREssEDO031 [0.79)
BELOW ENDS OF GEAR.
10 LUBE HOLES TO BE CHECKED
PRIOR TO ASSEMBLY HOLES MUST
BE FREE OF DIRT & BURRS
1. TORQUE OUTPUT SHAFT NUT TO
200-250 Ib.ft [271,2-338.9 N.m.)
2. ALL LEAD-IN CHAMFERS FOR OIL
SEALS, PISTON RINGS & "0"
RINGS MUST BE SMOOTH & FREE
FROM BURRS INSPECT AT
ASSEMBLY
3 LUBRICATE ALL PISTON RINGS &
"0" RINGS AT ASSEMBLY
4 APPLY THIN COATING OF GREASE
BETWEEN SEAL LIPS ON LIP TYPE
SEALS PRIOR TO ASSEMBLY
5 USE PERMATEX & CRANE SEALER
ONLY WHERE SPECIFIED
6. APPLY VERY LIGHT COAT OF
PERMATEX NO 2 TO O.D. OF ALL
OIL SEALS BEFORE ASSEMBLY
MUST BE LOOSE INTERNAL
FIT BEARING. NO. "3" ETCHEO
ON BEARING.-
~
NEEDLE BEARINGS TO BE ~
PRESSED .03 [0.7] BELOW
ENDS OF GEAR.
r-LOCKWIRE
.005 [0.13] MIN. CLEARANCE
7 INSPECT AT ASSEMBLY.
TWO PLATE
CLUTCH
:~6[14.2J~
4
~
LOCK TAB
(
I
/
~
1
~
-
./
-!JJ
.31 [7.9]
ONE PLATE
CLUTCH -
PERMATEX 2 STUDS USED
ON SHIPPING COVER -
STRAIGHT THRU DRIVE
/
~
/
~
/
GOVERNOR DRIVE
/ OFFSET DRIVE WITH LOCK-UP
LTORQUE ;URBINE BOLTS
TO 30-35 LBS./Ft. [40,7-47,4 N.m. NOTE: METRIC OIMENSIONS
SHOWN IN BRACKETS[
\
3
AUTOMATIC LOCK-UP
f] ADAPTOR OPTION
~
r ASSEMBLY INSTRUCTIONS FOR C-270 CONVERTER
WITH LOCK-UP AND OTHER OPTIONS
15 -
I
I
DISASSEMBLY OF THE LOCK-UP PORTION
OF THE CL-270 SERIES CONVERTER
After the Converter has been removed from
the vehicle and the exterior thoroughly cleaned
to prevent dirt and foreign matter from entering
the mechanism.
I
I
Figure 3
Remove turbine shaft lock-up oil sealing piston ring.
I
Figure 1
Remove impeller cover to impeller bolts and washers.
Figure 4
Remove turbine retaining ring.
I
Figure 2
Remove impeller cover. Note: Lock-up clutch disc parts
will come off with impeller cover.
Figure 5
If turbine hub is to be removed, straighten lock tabs from
bolt heads and remove bolts, disc hub and turbine ring.
-18-
I
Figure 6
Remove lock-up end plate bolts.
Figure 9
Remove outer drive disc.
Figure 7
Remove end plate.
Figure 10
Remove lock-up piston. NOTE: This may require turning
impeller cover over and tapping on a wooden bench to
remove piston.
Figure 8
NOTE: Some units will have a two friction plate and one
steel plate clutch and some units will have a single friction
plate clutch. The one shown is a single friction type.
Remove friction disc.
Figure 11
Remove outer piston oil sealing ring.
-19-
I
I
I
I
Figure 12
Remove piston inner sealing ring.
See CLEANING AND INSPECTION section.
REASSEMBLY OF LOCK-UP COVER.
Figure 15
Install piston in impeller cover as shown.
I
Figure 16
Align holes in outer drive disc with holes in impeller cover
and install drive disc.
I Figure 13
Install a new inner piston oil sealing ring.
I
Figure 17
Some units will have a two friction plate clutch and some
units will have a single friction plate clutch. On a Two plate
clutch install one friction plate (teeth on the inner diameter)
as shown. Install one steel plate with teeth on the outer
diameter. Install second friction plate (teeth .on the inner
diameter). On a single friction plate install plate as shown.
Figure 14
Install outer piston oil sealing ring.
-20-
Figure 18
Install end plate as shown.
Figure 21
Install turbine shah lock-up oil sealing ring on turbine
shaft.
Figure 19
Install end plate bolts and tighten 23 to 25 Ft. Lbs. Torque
[31,2- 33,8 N.m.].
Figure 22
Position new impeller to impeller cover oil sealing ring on
impeller cover assembly.
Figure 23
Install impeller to impeller cover bolts and tighten 23 to 25 Ft.
Lbs. Torque [31,2 -33,8 N.m.J.
Figure 20
Position turbine on turbine shaft and install retaining ring.
-21 -
AUTOMATIC LOCK-UP&TURBINE SHAFTTACHOMETER DRIVE DISASSEMBLY& REASSEMBLY
Remove Speed Sensor & Hydraulic Line From Tachometer & Drive Adaptor
DISASSEMBLY
1
?
3.
4.
Remove Tachometer Adaptor Housing Bolts -Item 2 and Washers -Item 1.
Remove Tachometer Housing -Item 4 from Converter Housing.
Note: Tach Drive Shaft and Bearings will come off with the Tach Housing as an assembly. Remove Drive Shaft "a" Ring -
Item 12 from Shaft.
See Section " AA". Remove Bearing Snap Ring -Item 10 from Tach Housing.
Using a small punch in the end of the Tach Drive Shaft -Item 7 on the end where the Speed Sensor is attached, tap Shaft
from housing -Item 4. Remove Tach Housing "a" Ring -Item 11 from Housing.
Remove the two Tach Drive Shaft Piston Rings -Item 5 from Drive Shaft.
Remove Drive Shaft Bearing Snap Ring -Item 8 from Shaft.
Press Tach Drive Shaft Bearing -Item 9 from Shaft.
If ail Seal -Item 6 is to be replaced tap Seal from Housing -Item 4 from Speed Sensor End of Housing.
REASSEMBLY
5.
6.
7.
8.
9. Install a new Oil Seal -Item 6 in Housing with lip of Seal toward the large end of Housing.
10. Press Bearing -Item 9 on Tach Drive Shaft -Item 7.
11. Install Bearing Snap Ring -Item 8 on Tach Drive Shaft being certain Ring is in full position in Snap Ring Groove.
12. Install two new Drive Shaft Piston Rings -Item 5 on Tach Drive Shaft.
13. Install Tach Drive Shaft -Item 7 and Bearing Assembly into Tach Drive Housing -Item 4. Use caution as not to damage Oil
Seal -Item 6 or Piston Rings -Item 5 when installing Shaft in Housing.
14. See Section " AA" and install Bearing Snap Ring -Item 10 in Housing being certain Ring is in full position in Snap Ring
Groove.
15. If Roll Pin -Item 13 was removed, reinstall Roll Pin in Drive Shaft.
16. Install new "0" Ring -Item 11 on Drive Shaft Housing -Item 4.
17. Install new "0" Ring -Item 12 on Drive Shaft- Item 7.
18. Install Tach Drive Assembly on Converter Housing aligning Roll Pin -Item 13 with hole in Turbine Shaft. Use caution as not
to damage Housing or Drive Shaft "0" Rings.
19. Apply a %" [9,52 mm] band of Loctite Dri-\ock Adhesive No.202 (green) about Ys" [3, 17 mm] from the threaded end of the
Bolt- Item 2. Install all Bolts -Item 2 and Washers -Item 1 in Tach Drive Housing into Converter Housing. Tighten Bolts 15
to 17 ft. Ibs. Torque [20.4 1-23. 0 N.m] 2 3
d 4
A
/
SNAP RING
r I N GROOVE
5
/6
13
~
/
~
"
"
12
SECTION "A-A" 7
11--1'/
10
8
9
A
LOCKUP AND TURBINE SHAFT TACH DRIVE
-22-
IMPELLER HUB, TURBINE HUB AND BACKING RING WITH SPECIAL SCREWS
1. CLEAN HUB MOUNTING SURFACE AND TAPPED HOLES WITH SOLVENT. DRY THOROUGHLY BEING
CERTAIN TAPPED HOLES ARE DRY AND CLEAN.
2. INSTALL BACKING RING AND SPECIAL SELF-LOCKING SCREWS TO APPROXIMATELY .06 INCH [1,5) OF
SEATED POSITION. WITH A CALIBRATED TORQUE WRENCH, TIGHTEN SCREWS 40 TO 45 LBS. FT.
[54,3 -61,0 N.m.) TORQUE.
NOTE: ASSEMBLY OF HUB MUST BE COMPLETED WITHIN A FIFTEEN MINUTE PERIOD FROM START OF
SCREW INSTALLATION. THE SCREWS ARE PREPARED WITH AN EPOXY COATING WHICH BEGINS TO
HARDEN AFTER INSTALLATION. IF NOT TIGHTENED TO PROPER TORQUE WITHIN THE FIFTEEN
MINUTE PERIOD, INSUFFICIENT SCREW CLAMPING TENSION WILL RESULT.
THIS SPECIAL SCREW IS TO BE USED FOR ONE INSTALLATION ONLY. IF THE SCREW IS REMOVED FOR
ANY REASON IT MUST BE REPLACED.
THE EPOXY LEFT IN THE HUB HOLES MUST BE REMOVED WITH THE PROPER TAP AND CLEANED
WITH SOLVENT. DRY HOLE THOROUGHLY AND USE A NEW SCREW FOR REINSTALLATION.
ASSEMBLY INSTRUCTIONS FOR C-270 CONVERTER
WITH SPECIAL APPLICATION IMPELLER HUB BEARING.
-23-
32 SCREW STABLE DRIVE CONNECTION NON-ASBESTOS CONVERTER DRIVE
RING GEAR INSTALLATION PROCEDURE
Remove all burrs from flywheel mounting face and pilot bores. Clean the torque converter ring gear flywheel mounting surface
and the ring gear screw tapped holes with solvent. Dry thoroughly, being certain ring gear screw holes are dry and clean.
2. Check engine flywheel and housing or housing adaptor for conformance to standard S.A.E. No.3 -SAE J927 and J1033
tolerance specifications for pilot bores size, pilot bores eccentricities and mounting face deviations. Measure and record engine
crankshaft end play.
3. Install torque converter ring gear as shown.
NOTE: Assembly of the ring gear must be completed within a fifteen minute
period from start of screw installation. The screws are prepared with an epoxy
coating which begins to harden after installation in the flywheel mounting holes. If not
tightened to proper torque within the fifteen minute period insufficient screw clamping
tension will result.
4. Install backing ring and thirty-two (32) special screws to approximately .06 inch [1 ,5 mm] of seated position. It is permissible to
use a power wrench for this installation phase. With a calibrated torque wrench tighten screws 23 to 25 pounds feet of torque
[31,2- 33,8 N.m].
To obtain maximum effectiveness of the special screw's locking featured, a minimum time period after screw installation of
twelve (12) hours is suggested before engine start-up.
5.
The special screw is to be used for ONE installation only. If the screw is removed for any reason is MUST BE REPLACED. It is
recommended that the epoxy left in the flywheel hole be removed with the proper tap and cleaned with solvent. Dry hole
thoroughly and use a NEW screw for re-installation.
Assemble torque converter to engine flywheel by sliding converter into position by hand before fastening housing attachment
screws. This may require more than one trial to match the drive gear teeth. Pulling the converter into position with housing
attachment bolts is not recommended.
6. Measure engine crankshaft end play after assembly of torque converter. This value must be within one thousandth (.001) of an
inch [0,0254 mmJ of end play recorded (in Paragraph #2) before assembly of torque converter.
802649 -1.5INCH [38,1] 32 SCREW RING GEAR KIT 802652- 2.5 INCH [63,5] 32 SCREW RING GEAR KIT
249473
243970
802655
SDC Torque Converter Ring Gear
Ring Gear Screw 1.5 Inch [38, 1]
Installation Instruction Sheet
1
32
1
249473
237153
802655
SDC Torque Converter Ring Gear
Ring Gear Screw 2.5 Inch [63,5]
Installation Instruction Sheet
1
32
1
802653 -3.0 INCH [76,2] 32 SCREW RING GEAR KIT 802650- 1.75 INCH [44,4] 32 SCREW RING GEAR KIT
SDC Torque Converter Ring Gear
Ring Gear Screw 1.75 Inch [44,4]
Installation Instruction Sheet
1
32
1
249473
236938
802655
SDC Torque Converter Ring Gear
Ring Gear Screw 3.0 Inch [76,2]
Installation Instruction Sheet
1
32
249473
244903
802655
802651 -2.0 INCH [50,8] 32 .SCREW RING GEAR KIT 802654 -M8-32 SCREW RING GEAR KIT
249473
240318
802655
SDC Torque Converter Ring Gear
Ring Gear Screw 2.0 Inch [50,8]
Installation Instruction Sheet
1
32
1
249473 SDC Torque Converter Ring Gear
4200097 Ring Gear Screw [MB x 1.25]
802655 Installation Instruction Sheet
1
32
1
236937 Backing Ring Not Included in Ring Gear Kit. Must be Ordered Separately.
NOTE: The initial installation drive gear mounting kit includes a converter air breather. This breather is used on C & CL 270/C
& CL 320 converters only and is not required for the HA & LHA 28000/Hr & LHA 32000 applications.
SEE PAGE 25 FOR INSTALLATION ILLUSTRATIONS
24
-~/ BACKING RING
1
ENGINE FL YWHEEL
~~
I
/
/
TORQUE CONVERTER
RING GEAR
RING GEAR SCREW
ENGINE FL YWHEEL
RING GEAR SCREW
(32) 243970 1.500 [38.1 ] '"
(32) 2449031.750 [44.4] ,
(32) 240318 2.000 [50.8]
(32) 237153 2.500 [63.5]
(32) 236938 3.000 [76.2]
(32) 4200097 [M8 x 1.25]
--~ -~-.::J
SEE PAGE 24
FOR INST ALLA TION
PROCEDURE AND
BOL T TORQUE
"
.I I I
l#,~
BACKING RING
236937
TORQUE CONVERTER RING GEAR 249473
-25-
I
SPEED SENSOR INSTALLATION
VIEW "T" (Pump Drive Gear Sensor)
Inspect at assembly.
Dim. "U" from gear tooth.
REAR VIEW OF CONVERTER
\ t
0
\
~i
~
~
")
After curing of Loctite,
speed sensor bushing
must be secure with 40
Ft. Lb. [54.2 N.m] torque
:~
~ ..,.,.,." , '\' .)-~, .' \\,)
VIEW "S" (Output Drive Gear se ~sor) O
Inspect at assembly.
Dim. "W" from gear tooth. --
Assemble Speed Sensor Bushing in housing to specified
dimension "U" or "W" with Loctite 262 and stake (3) three
places. See Pump Drive and Output Gear Charts for dimensions.
PUMP DRIVE RATIO
DRIVE
NO. OF
3~
4.
SPEED SENSOR BUSHING
DEPTH "U" PER VIEW "T"
1.060:f: .007 [26.9:f: .17]
1 .060 :f: .007 [26.9:f: .17]
~ ATIO 1.135
.951
OUTPUT GEAR RATIO (6 PITCH)
TURBINE SHAFT
& GEAR ASS'y
NO. OF TEETH
24
RATIO
SPEED SENSOR BUSHING
DEPTH ..W.. PER VIEW ..S..
1.060:t .007 [26.9t .171
1.060 t .007 [26.9 t .17]
1.390t .007 [35.3t .17]
1.390:t .007 [35.3t .17]
1.390:t .007 [35.3 t .17]
* Requires straight thru housing plus bore plug
OUTPUT GEAR RATIO (5.35 PITCH)
TURBINE SHAFT
& GEAR ASS'V
NO. OF TEETH
21
23
24
25
26
SPEED SENSOR BUSHING
DEPTH ..W.. PER VIEW ..S..
1.060:t .007 [26.9:t .17]
1.060:t .007 [26.9:t .17]
1.390:t .007 [35.3:t .17]
1.390:t .007 [35.3:f: .17]
1.390:t .007 [35.3:f: .17]
.26-
28000/32000 SERIES TRANSMISSION AND C-270/C-320 CONVERTER DRIVE PLATE
INSTALLATION INSTRUCTIONS
Proper Identification by Bolt Circle Diameter.
Measure the "A" dimension (Bolt Circle diameter) and order Drive Plate Kit listed below
AlIgnment Holes
I
(1) Drive Plat. and
Weld Nut Assembly
Washer
s,~~{~
,,\ .\:
~~"
"~,,
Diameter
Backing Ring
AlIgnment Holes
~-/
~
Washer
-'
,
~ \:
~~'\
'\0,\
(4) Intermediate
Backing Ring Drive Plates
Screw
~\
-(5) Intermediate
DrIve Plates
"A"Dimension (Bolt Circle Diameter)
13.125" [333,375 mm] Diameter
Kit No.802335
"A" Dimension (Bolt Circle
Diameter)
13.125" [333.375 mm] Diameter
Kit No.802521
13.50 [342,900 mm] Diameter
Kit No.802517
NOTE: Assembly of flexplates must
be completed within a 15 minute
period from start of screw installa-
tion. If the screw is removed for any
reason it must be replaced. The
adhesive left in the tapped hole must
be removed with the proper tap and
cleaned with solvent. Dry the hole
thoroughly and use a new screw for
reinstallation.
13.50" [342,900 mm] Diameter
Kit No.802568
17.00" [431,800 mm] Diameter
Kit No.802454
17.00" [431 ,800 mm] Diameter
Kit No.802566
Each kit will include the following parts
5 Intermediate Drive Plates
1 Backing Ring
10 Drive Plate Mounting Screws
10 Drive Plate Washer
1 Instruction Sheet
Each kit will include the following parts:
4 Intermediate Drive Plates
1 Drive Plate and Weld Nut Assembly
1 Backing Ring
10 Drive Plate Mounting Screws
10 Drive Plate Washer
1 Instruction Sheet
TO FACILITATE ASSEMBLY, ALIGN SMALL HOLES IN DRIVE PLATES-SEE ILLUSTRATION ABOVE.
Position drive plate and weld nut assembly on impeller cover with weld nuts toward cover. Align intermediate drive plate and
backing ring with holes in impeller cover. NOTE: Two dimples 180 degrees apart in backing ring must be out (toward engine fly-
wheel). Install capscrews and washers. Tighten 33 to 36 ft. Ibs. torque [45-49 N.m]
Over for TRANSMISSION TO ENGINE INSTALLATION PROCEDURE
-27-
I
I
TRANSMISSION TO ENGINE INSTALLATION PROCEDURE
1
2.
I
3.
4.
I
5.
I
6,
7,
I
I
I
8.
Remove all burrs from flywheel mounting face and
nose pilot bore. Clean drive plate surface with solvent.
Check engine flywheel and housing for conformance
to standard S.A.E. #3 -S.A.E. J-927 tolerance
specifications for pilot bore size, pilot bore runout and
mounting face flatness. Measure and record engine
crankshaft end play.
Install two 3.50 [88,90 mm] long transmission to
flywheel housing guide studs in the engine flywheel
housing as shown. Rotate the engine flywheel to align
a drive plate mounting screw hole with the flywheel
housing access hole.
Install a 4.00 [101 ,60 mm] long drive plate locating
stud .3750-24 fine thread in a drive plate nut. Align the
locating stud in the drive plate with the flywheel drive
plate mounting screw hole positioned in step No.3.
Locate transmission on flywheel housing aligning
drive plate to flywheel and transmission to flywheel
housing.
Install transmission to flywheel housing screws.
Tighten screws to specified torque. Remove trans-
mission to engine guide studs. Install remaining
screws and tighten to specified torque.
Remove drive plate locating stud.
Install drive plate attaching screw and washer. Snug
screw but do not tighten. Some engine flywheel
housings have a hole located on the flywheel housing
circumference in line with the drive plate screw access
hole. A screwdriver or pry bar used to hold the drive
plate against the flywheel will facilitate installation of
the drive plate screws. Rotate the engine flywheel and
install the remaining seven (7) flywheel to drive plate
attaching screws. Snug screws but do not tighten.
After all eight (8) screws are installed torque each one
25 to 30 ft. Ibs. torque [33,9 -40,6 N.m.]. This will re-
quire torquing each screw and rotating the engine
flywheel until the full amount of eight (8) screws have
been tightened.
Measure engine crankshaft end play after trans-
mission has been completely installed on engine
flywheel. This value must be within .001 [0,025 mm]
of the end play recorded in step No.2.
I
I
I
-28-
I