LG 21fu7rl Chasis CW81B PDF

Internal Use Only
website:http://biz.LGservice.com
COLOR TV
SERVICE MANUAL
CHASSIS : CW81B
MODEL : 21FU7RL/RLG/RG
MODEL : 21FU7RL/RLG/RG-T4/Z4
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : MFL42115604
June., 2008
Printed in China
CONTENTS
CONTENTS ............................................................................................... 2
SAFETY PRECAUTIONS...........................................................................3
SPECIFICATIONS ......................................................................................4
ADJUSTMENT ...........................................................................................6
TROUBLE SHOOTING ............................................................................13
BLOCK DIAGRAM ...................................................................................17
PRINTED CIRCUIT BOARD ....................................................................18
EXPLODED VIEW ....................................................................................20
Copyright2008 LG Electronics.Inc. All right reserved.

Only for training and service purposes.
-2-
LGE Internal Use Only
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by
in the
Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
Before returning the receiver to the customer,
An isolation Transformer should always be used during the

servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)

It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube. Do
not lift the Picture tube by it's Neck.
X-RAY Radiation
Warning:
The source of X-RAY RADIATION in this TV receiver is the High
Voltage Section and the Picture Tube.
For continued X-RAY RADIATION protection, the replacement
tube must be the same type tube as specified in the
Replacement Parts List.
To determine the presence of high voltage, use an accurate high

impedance HV meter.
Adjust brightness, color, contrast controls to minimum.
Measure the high voltage.
The meter reading should indicate
23.5 1.5KV: 14-19 inch, 26 1.5KV: 19-21 inch,
29.0 1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service and
correction is required to prevent the possibility of premature
component failure.
With the instrument AC plug removed from AC source, connect an

electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1M and 5.2M.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
AC Volt-meter
To Instruments
exposed
METALLIC PARTS
Good Earth Ground

such as WATER PIPE,
CONDUIT etc.
0.15uF
1.5 Kohm/10W
-3-
SPECIFICATIONS
Note : Specification and others are subject to change without notice for improvement.
Scope
This specification is applied to all the television related to CW 81B Chassis.
5) The receiver must be operated for about 20 minutes prior to

the adjustment.
Test Method
1) Performance : LGE TV test method followed.
2) Demanded other specification
Requirement for Test

Each part is tested as below without special appointment.
1) Temperature : 25 5C (77 9F), CST : 40 5
2) Relative Humidity : 65 10%
3) Power Voltage : Standard input Voltage AC220V ~ 50/60Hz.
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
Model
Remark
Market
T4/Z4 Model PAL Model
Appliance
Safety: CB Spec. (EN60065)

EMC: CE Spec (EN55020,
EN55013)
General specification
No.
1
Item
Receiving System
Specification
Remark
PAL BG, DK, I / NTSC M (AV 3.58/ 4.43)
China/ Indonesia/ Thai/ Vietnam
CIS
SECAM DK
PAL NM / NTSC M (AV 3.58)
L America/ Philippines/ Taiwan
Asia/Middle East/ Africa
SECAM BG, DK, L

2
Available Channel
VHF : E2 ~ E12
UHF : E21 ~ E69
PAL Model
CATV : S1 ~ S20
HYPER : S21 ~ S41
3
4
Input Voltage
Market
AC220V ~ 50/60Hz
East Asia
AC100 ~ 240V, 50/60Hz
Others
Korea, Latin America, China, Indonesia,

Philipines, Taiwan, Thai, Vietnam, Asia,
Africa
Screen Size
Aspect Ratio
4:3
Display Method
CRT
Tuning System
FVS
Operating Environment
1) Temp : 0 ~ 40 deg
14 ~ 21 inch (FLAT / Conventional)

21'' Superslim/Ultraslim
PAL Model
2) Humidity : ~ 85 %
10
Storage Environment
1) Temp : -20 ~ 60 deg

2) Humidity : ~ 90 %

-4-
Features and Function (For China. Indonesia, Vietnam, Thai, CIS / Middle East Asia, Africa)
No.
1
Feature
AV Input
Remark
Specification
Item
2
Rear1, Front1(CVBS,L,R)
AV 1, 2
Tool Option (For China, Vietnam,Thai,CIS)
Key
Channel
Picture
AV Output
Monitor out
Rear
Component
Input (For component)
Rear (Y,Pb,Pr,DVD-L/R)
Local Key
Power, Vol(F, G), PR(E, D), MENU, OK
7EA/ Front
Turbo-Picture, Sound
Option
Remocon
LG Code (NEC)
Auto prog.
System/ Storage/ Normal/ Turbo
Manual
Storage/ System/ Channel/ Fine/ Search/ Name
Prog. edit
Copy/ Move/ Delete/ Skip
Favorite
8 Channel
PSM
Dynamic/ Standard/ Mild/ Game/ User
User Control
Contrast/ Brightness/ Color Sharpness
Tint: NTSC System only
Tint (NTSC-M Only)
Sound
Timer
Special
Etc.
8
XD
ON/OFF
option
SSM
Flat/ Music/ Movie/ Speech/ User
AV, RF Stereo Option
Treble/ Bass
0 ~ 100
AV, RFStereo
Turbo SND
ON/ OFF
Option For Middle East Aisa/Africa
FM Transmitter
Wide Range (191ch)
Option
(Option)
88.0MHz ~ 107.0MHz
Clock
-- : --
Off time
-- : -- Off(On)
On time
-- : -- Pr 1 VOL 30 Off (On)
Auto off (Sleep)
On/ Off
(Sleep) For Middle East Asia/Africa
Language
English/ Indonesia/ Thai/ Vietnam
East Asia
Input
TV/ AV1/ AV2/ Component
AV2 Option
Child lock
On/ Off
Sleep
Review

-5-
ADJUSTMENT
1. Scope of Application
4. Screen Voltage Adjustment
These instructions are applied to CW81B Chassis.
4-1. Adjustment (Using Factory Remote Control)

1) Input in the 75 cable LG standard signal (Digital Pattern,
480NC).
2) Press the ADJ key of factory remote control once to make
the TV set display horizontal line.
3) Turn the screen volume on the FBT clockwise until the
horizontal line is visible and turn it counterclockwise until
horizontal line faintly visible.
(Exit screen voltage adjustment by press Enter(A) key of
factory remote control.)
2. Notes
1) Because this is a cold chassis, it is not necessary to use an
isolation transformer. However, operating it using a
transformer between the power supply line and chassis input
to prevent electric shock and to protect the test instrument.
2) All adjustment must be done in the correct sequence.
However, for better productivity, it can be change in a prepermitted range.
3) Environment conditions : If not specified, it must be done in
following conditions.
Temperature : 25 5C
Humidity: 60% 10%
4) Power supply of SET for PAL/SECAM
China/indonesia/Vietnam/CIS Market: AC100~240V10%,
50/60Hz.
5) If not specified, the receiver must be operated for more than
20 minutes prior to the adjustment.
6) Signal : Received the standard color signal (65dB1dBuV).
PAL/SECAM: LG standard signal means the digital pattern
PAL-B/G 05CH.
7) If not specified, APC ON is APC CLEAR (DYNAMIC)
5. Purity and Convergence Adjustment

5-1. Purity adjustment
(1) Adjustment Preparation
1) Receive Red Raster Pattern for purity adjustment (51CH).
2) Demagnetize the CPT and Cabinet with a degaussing coil.
(2) Adjustment
1) Pre-adjust the static convergence (STC) with the 4 and
6pole magnet.
2) If the horizontal Line is inline with CPT Mark, 2-Pole
magnet should direct 3-9 oclock direction.
3) If not, direct 2-pole magnet handle toward 6-12 oclock
direction and adjust the Horizontal Line to fall onto the
mark opening the magnet at an angle.
4) Push the DY(deflection yoke) all the way to the CPT
funnel.
5) Turn the purity magnet(2-pole magnet) so that the green
color portion of left side and the blue color portion on the
right side have equal amount of color.
3. AGC Voltage Adjustment

3-1. Necessary Instrument
- Digital Multi-meter: 1 set
- Max Input Current : Over 1A/ Max Input Voltage : 500Vdc
- Measurement Range : 10mV-100mVdc/ Accuracy : 0.03%
3-2. Adjustment Preparation

1) Input in the 75 cable 65dB(1dB) LG standard signal.
2) Connect the multi-meter to J105 (AGC Check, Marking).
3-3. Adjustment
1) Press the INSTART key of factory remote control and
select VP0 (RF AGC) adjustment mode.
2) Press the VOL+/- (F/ G) key until the multi-meter shows
reading as shown below.
3) CAUTION: Since the signal strength can be easily
changed by the condition of signal cable, you need to
check the signal strength frequently in order to prevent
error.
Tuner P/N
Maker
AGC Vol
Signal
Tuner Spec.
Remark
6700NFNS11E
LGIT
2.15 0.05V
65dBu
TAEA-H111F
Korea
6700VS0002F
LGIT
3.0 0.05V
70dBu
TAEW-G002D
PAL
6700PF0006B
SANYO
2.3 0.05V
65dBu
115-B-A86EL
PAL
6870NB0026A
LGIT
2.15 0.05V
65dBu
TAEA-J001F
HITACHI
6700MF0014A
LGIT
2.3 0.05V
65dBu
TAEW-G013D
PAL
6700MF0014B
LGIT
2.15 0.05V
65dBu
TAEW-G017D
SECAM(CIS)
6700MF0018B
LGIT
2.4 0.05V
65dBu
TAEA-G001D
PAL
6700MF0018A
LGIT
2.5 0.05V
65dBu
TAEA-G011D
SECAM(CIS)
6) Pull the DY slowly backward and fix it when the whole

screen becomes red.
(The specified torque for fixing DY screw should be
10Kg/cm.)
5-2. Convergency Adjustment

(1) Necessary Instrument
1) Degaussing Coil
2) Convergency fixing instrument (Speical tools)
(2) Adjustment Preparation

1) Operate the unit at least 15 minutes before adjustment.
2) Using degaussing coil, remove the stains on CPT &
Cabinet.
3) Received the Cross Hatch Pattern of Convergence. (09ch)
4) Let the Contrast in normal luminance level.
(3) Static Convergence (STC) Adjustment

1) Receive the Cross Hatch Pattern Convergence (09ch).

-6-
2) Before adjusting Static Convergence (STC), adjust the

focus first seeing to it that the WHITE color picture quality
is sharp enough.
3) Converge the RED vertical and BLUE vertical line in unity
(same line) by changing the angle between the 2 tabs of
4-pole magnet.
4) Converge the RED horizontal and BLUE horizontal line in
unity(same line) by turning the 2 tabs of the 4-pole
magnet. At this time, do not change the angle between
the 2 tabs.
5) Converge the R, G, B vertical line in unity (same line) by
changing the angle between the 2 tabs of the 6-pole
magnet.
6) Converge the R, G, B horizontal line in unity(same line) by
turning the 2 tabs of the 6-pole magnet. At this time, do
not change the angle between the 2 tabs.
(4) Dynamic Convergence (DYC) Adjustment

1) Y-axis Adjustment:
Adjust convergence of Y-axis (vertical) by moving the
deflection yoke (DY) left and right.
2) X-axis Adjustment:
Adjust convergence of X-axis (horizontal) by moving the
deflection yoke (DY) up and down.
light with B-BIAS to have the color temperature as

shown below.
e. Repeat steps a~d until both low and high light have the
same readings as shown below.
Market
Color Temperature
ALL
13,000
X-AXIS
Y-AXIS
2685
2735
7. Focus Voltage Adjustment

This adjustment must be done after operating the TV set
receiver sufficiently.

Receive the LG standard pattern (PAL: Digital pattern,
480NC,13CH) and set the picture condition on APC ON
(CLEAR) mode.
7-2. Adjustment
Turn the focus volume on the FBT upper direction to have
the best focus vertical line (Fig. 1(a)) and horizontal line (Fig.
1(b)) as shown below.
(a)
6. White Balance Adjustment

6-1. Necessary Instrument
(b)
1) Automatic White Balance Meter (Low/High light Pattern

generator)
2) CRTColor Analyzer, CA -100: 1 set
3) Factory Remote Control
<Fig. 1>

Prior to this adjustment, the Screen Voltage adjustment
should be finished.
8. SUB-BRIGHTNESS Adjustment
This adjustment must be done after White balance adjustment.
6-3. Automatic adjustment

1) Adjust using Auto White Balance Meter.
2) Enter CPU OFF Mode by pressing IN-START & MUTE
key of factor remote control in turn before adjustment.
Exit CPU OFF mode by press the MUTE key of factory
remote control after adjustment finished.
* In case there is excess RED color at screen voltage
adjustment, adjust it using volume - (F) key of factory remote
control until the RED color disappear.

1) Receive PAL B/G 5CH pattern.
2) Set the picture condition on PSM ON (DYNAMIC) mode.
8-2. Adjustment
6-4. Manual adjustment

1) Adjust using white Balance meter and factory remote
control.
2) Enter white balance adjustment mode by pressing
INSTART key of factory remote control.
3) Use the CHD, CHE Key to choose adjustment item.
4) Use the VOLF, VOLG Key to change item data.
5) Adjustment Procedure
a. Make the picture luminance 45Ft-L by changing the
CONTRAST and BRIGHTNESS.
b. Adjust X data of High light with R-DRIVE and Y data of
high light with B-DRIVE to have the color temperature
as shown below.
c. Make the picture luminance 4.5Ft-L by changing the
CONTRAST and BRIGHTNESS.
d. Adjust X data of low light with R-BIAS and Y data of low

-7-
1) Press the ADJ key of the factory remote control twice to

enter to SUB-BRIGHTNESS adjustment mode.
2) Change the Sub-Brightness data by pressing the VOLF,
VOLG key so that the 1th, 2th black level in gray scale of
PAL B/G 05CH pattern have a little bit of difference.
(See Fig. 2)
1th VS 2th
BLACK LEVEL have a bit of difference.
(In case of Vietnam Model 2th VS 3th)
<Fig. 2> PAL B/G 05CH Signal
8-3. Sub-Tint adjustment
be parallel to the vertical line of the center of screen. (or the

remotest grid of CPT)
7) Trapezoidal Adjustment
Select SVC02(EW TRAPE) and adjust so that the width of
the upper part of screen is alike with the one of the lower part
of the screen.
8) EW UPCOR / LOCOR Adjustment
Select SVC02(EW C UPCOR, EW LOCOR) and adjust so
that the vertical line in the four corners become straight line.
9) BOW Adjustment
Select SVC02(HP BOW) and adjust so that the vertical line in
the four corners become straight line.
This adjustment has to be done only if the picture has bad tint
otherwise, it can be omitted if the picture has good tint.
1) Receive LG standard pattern signal (SMPTE, 2CH)
2) Set the picture condition on APC ON (CLEAR) mode.
3) Press the ADJ key of the factory remote control three
times to enter to SUB-TINT adjustment mode.
4) Change the Sub-Tint data by pressing the VOLF, VOLG
key until the upper and lower CYAN color becomes same
color.
9. Deflection setting data adjustment

These adjustment will be done by automatic adjustment
Equipment.
For manual adjustment, it is also possible by the following
procedure.
10. IIC BUS SUB Adjustment Data

Table
OSD
SUB-BRIGHTNESS
SUB-TINT

1) Deflection setting data adjustment can be done only with
remote control.
2) Press IN-START key on factory remote control continuously
to enter to Deflection Adjustment mode.
3) Press the CHD, E key to select adjustment item.
4) Press the VOLF, G key to change the data.
Range
0 ~ 100
-20 (R) ~ +20 (G)
PAL
40
R5
NTSC Secam
60
40
G8
R5
11. Auto Adjustment Preparation

Setting Table
VIDEO IC
BA
SLave ADD
9-2. Adjustment
1) Horizontal Position Adjustment
Select SVC02(H-POS) and adjust so that the left and right
vertical line are symmetrical as possible.
2) Vertical Position Adjustment
Select SVC02(V-POS) and adjust so that the horizontal
center line coincide with geometric horizontal center of the
CPT.
3) Vertical Size Adjustment
Select SVC02(VA) and adjust so that the middle circle of the
Digital Pattern(480NC, 13CH) coincide with the effective
screen of CPT.
EEPROM
A0
R BIAS
B DRIVE
B BIAS
Sub Add
Start Bit
Stop Bit
Masking
Direction
8D
8A
8F
8C
SpeedPlus
Step/Data
B AMP
B CUT G AMP G CUT
PC
R DRIVE
Sub Add
Delay
5
TV
VCD
EEPROM
Speed
1
9-3. Adjustment (21'' Superslim, Ultra S/S

Model)
1) Vertical Position Adjustment
Select SVC02(V-POS) and adjust so that the horizontal
center line coincide with geometric horizontal center of the
CPT.
2) Vertical linearity Adjustment
Select SVC02(V-LIN) and adjust so that the size of the upper
circle is alike with the one of the lower circle at LG standard
pattern (PAL: EU05CH, NTSC: 13CH)
3) Vertical Size Adjustment
Select SVC02(VA) and adjust so that the middle circle of the
Digital Pattern(PAL B/G 5CH) has 6~7mm gaps from the
effective screen of CPT
4) Horizontal Position Adjustment
Select SVC02(H-POS) and adjust so that the left and right
vertival line are symmetrical as possible.
5) Horizontal Size Adjustment
Select SVC02(EW WIDTH) and adjust so that the outer line of
the left and right and the remotest grid will correspond to the
effective boundary surface. (The remotest grid PAL: within
0~25%; NTSC: within 2.5~3.0 column)
6) Parabora Adjustment
Select SVC02(EW PARAB) and adjust so that the vertical line
of the remotest grid at the left or right side of the screen will

-8-
12. EEPROM OPTION TABLE
( <Table 1> PAL MODEL SOUTH EAST, <Table 2> PAL MODEL MIDDLE EAST)
You can find the EEPROM Option Data if entering the IN-START key of the adjustable remote control and then pressing the MENU key.
OPTION 1
CODE
CPT
0/1
0: Slim/Ultra, 1:Normal/Flat
DESCRIPTION
REMARK
OPTION 1
CODE
CPT
0/1
1: Slim/Ultra, 0:Normal/Flat
DESCRIPTION
REMARK
XD MENU
0/1
1: With; 0: Without
XD MENU
0/1
1: With; 0: Without
TURBO SND
0/1
1: With; 0: Without
TURBO SND
0/1
1: With; 0: Without
V-CURVE
0/1
1: Volume Curve high; 0: Volume Curve low
V-CURVE
0/1
1: Volume Curve high; 0: Volume Curve low
V-MUTE
0/1
1: WithVideo Mute; 0: Without
V-MUTE
0/1
1: With Video Mute; 0: Without
SND MUTE
0/1
1: WithSound Mute(no signal);0: Without(no signal)
SND MUTE
0/1
1: With Sound Mute(no signal);0: Without(no signal)
OPTION 2
CODE
Teletext
0/1
1: With; 0: Without
DVD
0/1
1: With DVD input; 0: Without
SCART
0/1
1: With; 0: Without
EYE
0/1
1: With; 0: Without
OPTION 2
CODE
GAME
0/1
1: With Game Module ; 0: Without
DVD
0/1
1: With DVD input; 0: Without
DESCRIPTION
X-WAVE
0/1
1: With Blue Back; 0: Without X-WAVE
COLOR T
0/1
1: Color+10 STEP; 0: -
Degausss
0/1
HOTEL
REMARK
DESCRIPTION
REMARK
EYE
0/1
1: With; 0: Without
GAME
0/1
1: With Game Module ; 0: Without
1: With; 0: Without
X-WAVE
0/1
1: With Blue Back; 0: Without X-WAVE
0/1
1: With; 0: Without
COLOR T
0/1
1: Color+10 STEP; 0: -
200Pr
0/1
1: 200 Program; 0: 100 Program
Degausss
0/1
1: With; 0: Without
OPTION 3
CODE
HOTEL
0/1
1: With; 0: Without
NTSC
0/1
1: With NTSC system; 0: Without
200Pr
0/1
1: 200 Program; 0: 100 Program
DUAL SV
0/1
1: With DUAL SAVING; 0: Without
OPTION 3
CODE
PIP
0/1
1: SYNC KILL=1(no signal); 0: SYNC KILL=0 (no signal)
NTSC
0/1
1: With NTSC system; 0: Without
SND1 FL1
0/1
1: 75KHZ (mono filter); 0: 50KHZ (mono filter)
DUAL SV
0/1
1: With DUAL SAVING; 0: Without
SND1 FL2
0/1
1: 200KHZ(mono filter); 0: 100KHZ (mono filter)
PIPI
0/1
1: SYNC KILL=1(no signal); 0: SYNC KILL=0 (no signal)
SND2 FL1
0/1
1: WithA2STEREO direction; 0: Without
SND1 FL1
0/1
1: 75KHZ (mono filter); 0: 50KHZ (mono filter)
SND2FL2
0/1
1: WithNICAM direction; 0: Without
SND1 FL2
0/1
1: 200KHZ(mono filter); 0: 100KHZ (mono filter)
HIDEV
0/1
1: With; 0: Without
SND2FL1
0/1
1: WithA2STEREO direction; 0: Without
OPTION 4
CODE
REMARK
SND2 FL2
0/1
1: WithNICAM direction; 0: Without
OSD LANG
0: INDONE (IND/ENG)
INDONESIA
HIDEV
0/1
1: With; 0: Without
1: THAI (THA/ENG)
THAILAND
OPTION 4
CODE
2: VIETNA (VIE/ENG)
VIETNAM
OSD LANG
0: ENG (ENG)
3: MULTI: ENG/IND/THA/VIE
1: ARAB (ENG/FRE/ARAB/URUD)
4: AUS: ENG
2: FARSI (ENG/FARSI)
DESCRIPTION
DESCRIPTION
REMARK
DESCRIPTION
REMARK
DESCRIPTION
REMARK
SND MODE
0/1/2
0: MONO; 1: AV STEREO; 2: RF STEREO
TXT LANG
0/1/2/3 0: EU WEST; 1: EU EAST; 2: ARABIC 3: FARSI
AV
0/1/2
0: NO AV; 1: AV1; 2: AV1 2
OPTION 5
CODE
Local KEY
0/1/2
0: 4 KEY; 1: 6 KEY; 2: 8 KEY
Snd Mode
0/1/2
0: MONO; 1: AV STEREO; 2: RF STEREO
AV
0/1/2
0: NO AV; 1: AV1; 2: AV12
Local Key
0/1/2
0: 4 KEY; 1: 6 KEY; 2: 8 KEY
<Table 1>
DESCRIPTION
REMARK
<Table 2>

-9-
<TABLE 3 >
SVC
SVC 01
SVC 02
SVC 03
Register
RF AGC
R BIAS
G BIAS
B BIAS
R DRIVE
G DRIVE
B DRIVE
Y-DELAY
OSD CONT.
OSD POS.
V POS
V LIN
VA
H POS
EW WIDTH
EW PARAB
EW TRAPE
EW UPCOR
EW LOCOR
HP BOW
HP ANGLE
V SC
V COMP
HS COMP
V DC
VBLK SW
H BLK L
H BLK R
EW Cor
DEEM TC
FM GAIN
A2 SW
SIF SYS
CH CONV
FM MUTE
VOL FIL
VOLUME L
AUDIO SW
SURR CNT
MONO
VOLUME R
TONE ATT
T BOOST C
TREBLE
PSEUD ST
BBOOST C
BASS GA
S TRAP
S TRAP SW
F DDS
DELAY T
Y FILTER
C FILTER
SVC 04
Y APF
COR GAIN
P SHOOT
O SHOOT
WPL OPE
Range
0 ~ 63
0 ~ 255
0 ~ 255
0 ~ 255
0 ~ 127
0 ~ 127
0 ~ 127
0 ~ 15
0~7
0 ~ 60
0 ~ 15
0 ~ 31
0 ~ 127
0 ~ 31
0 ~ 127
0 ~ 127
0 ~ 127
0 ~ 31
0 ~ 31
0 ~ 31
0 ~ 31
0~7
0~7
0~7
0 ~ 63
0: normal mode; 1: wide mode
0~7
0 ~7
0: Normal mode; 1: Corner pin gain up mode
0: 50us ; 1: 75us
0: 500mVrms@ 50KHz. deviation (for PAL)
0: Normal mode; 1: 5.74MHz mode need to set SIF system=1
0: 4.5MHz; 1: 5.5MHz; 2: 6.0MHz; 3: 6.5MHz
0: Normal BPF mode; 1: CH converter measure mode at India
0: Enable FM output; 1: Disable FM output
0: Filter OFF; 1: TV operating mode
0 ~ 127
MONO Mode: 0 (0: Stereo EXT; 1: Stereo INT)
MONO Mode: 1 (0: MONO CH1; 1: MONO CH2; 0: MONO CH3; 1: MONO CH4)
0: Surround OFF; 1: MODE-A (-3dB); 2: MODE-B (0dB); 3:MODE-C(+3dB)
0: STEREO input mode; 1: MODE input mode
0 ~ 127
0: 0dB; 1: -6dB
0: Cut; 1: Boost
0 ~ 63
0: Pseudo Stereo OFF; 1: Pseudo Stereo ON
0: Cut; 1: Boost
0 ~ 63
0 (min) ~ 7 (max)
0: Sound trap OFF mode (need external trap); 1: Normal mode (sound trap ON)
0: Normal mode (NTSC: work; PAL/SECAM: stop);
1: Forced DDS mode (always work)
Delay Test
0: 3.58MHz Trap; 1: 4.43MHz Trap; 2: Wide mode; 3: 4.286MHz Trap
0: 3.58MHz peaking; 1: 3.58MHz symmetrical;
2: 4.43MHz peaking; 3: 4.43MHz symmetrical
0: Chroma trap ON (composite video mode)
1: Chroma trap OFF (YCbCr mode and YC mode)
0: Coring OFF; 1: Coring Gain 1(minimum);
2: Coring Gain 2(middle); 3: Coring Gain 3(maximum)
0 (narrow) ~ 3 (wide)
0 (narrow) ~ 3 (wide)
0: WPL OFF; 1: High operating point;
2:Middle operating point; 3: Low operating point

- 10 -
Initial(PAL)
32
90
90
90
85
95
85
4
5
42
9
22
92
4
74
44
39
21
8
16
16
18
7
7
28
3
4
4
0
0
0
0
1
0
0
1
50
0
Initial(SECAM)
32
90
90
90
85
95
85
4
5
42
9
22
92
4
74
44
39
21
8
16
16
18
7
7
28
3
4
4
0
0
0
0
1
0
0
1
50
0
Remark
Necessary
Necessary
Unnecessary
Necessary
Necessary
Unnecessary
Necessary
Unnecessary
Unnecessary
Unnecessary
Necessary
Unnecessary
Necessary
Necessary
Necessary
Necessary
Necessary
Necessary
Necessary
Necessary
Necessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
0
0
50
0
0
63
0
0
63
2
1
0
0
0
50
0
0
63
0
0
63
2
1
0
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
0
1
0
0
1
0
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
0
0
0
0
0
0
Unnecessary
Unnecessary
Unnecessary
SVC
Register
GAMMA ST
DC REST
BS START
SVC 04
BS GAIN
C TRAP
C BPF
GAMMA GA
GRAY MDE
YCMIX
TXT CC
VIN/XRGB
T DISABLE
H FREQ
AFC G
A MUTE
V MUTE
SYN KILL
V KILL
VSEP
V RES T
HLVDT
SVC 05
SVC 06
SVC 07
V SYN
CD MODE
FBPBLK
AFC NST
AFC2SW
CROSS BW
BLK DEF.
SUB BIAS
V TRANS
DIG OSD
RGB CONT
RGB TEMP
ACL DEF.
ACL SW
ABL DEF.
MID STP
ABL TH
VXO ADJ
CrCb IN
C EXT
C BYPASS
C KI ON
C KI OFF
C KI OPE
GRN ADJ
TINT TH
ID KILL
CVCO ADJ
VCO CNTR
FSC/EHT
C SYS
RY BY GA
RY BY AN
R-Y LEVEL
B-Y LEVEL
GY AMP
HTNo CIr
VXO Free
VXO Stby
Range
0: Low operating point; 1: Middle operating point;
2: High operating point; 3: Defect
0: 100%; 1: 107%; 2: 113%; 3: 129%
0: Black Stretch ON (Starting Point=401RE);
1: Black Stretch ON (Starting Point=501RE)
2: Black Stretch ON (Starting Point=601RE)
3: Black Stretch OFF
0 (min) ~ 2 (max)
0 (min) ~ 7 (max)
0 (min) ~ 3 (max)
0 (min) ~ 3 (max)
0: White (70%); 1: Gray (15%)
0: YC_C; 1: 2.2V_DC
0: Output without LPF; 1: Output by LPF
0: FBP/EXT RGB IN; 1: YC-C/DVD-Y/CR-IN/CB-IN
0: Test mode; 1: TV operating normally
0 ~ 63
0: Automatic mode; 1: Enforce high gain mode
0: Audio Mute OFF; 1: Audio Mute ON
0: Video Mute OFF; 1: Video Mute ON
0~1
0: TV operating mode; 1: Defeat the vetical output
0: Normal mode; 1: Sensitivity up mode
0: Normal mode; 1: Sensitivity up mode
0: If H-Lock is not defect, stop vertical sync detection
1: V sync system always working
0~7
0~1
0: Normal mode; 1: Enforce low gain mode (non-standard)
0: About 4us ~ 8us; 1: about 8us ~ 12us
0: TV operating mode; 1: Black pattern; 2: White pattern; 3: Crosshatch pattern
0: Blanking ON (normal mode); 1: Blanking OFF
0 ~ 127
0: Random transmission; 1: Transmission between vertical retrace period
0: Analogue OSD mode; 1: Digital OSD mode
0 ~ 15
0: -1VBE; 1: Flat
0: ACL Defect OFF; 1: ACL Defect ON
0: High sentivity; 1: Low sentivity
0: ABL Defect OFF; 1: ABL Defect ON
0: Enable limit operating; 1: Disable limit operating
0~7
Initial(PAL) Initial(SECAM)
3
3
1
0
1
0
Unnecessary
Unnecessary
1
4
0
0
0
0
0
1
1
70
0
0
0
0
0
0
0
0
1
4
0
0
0
0
1
0
1
70
0
0
0
0
0
0
0
0
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
0
0
1
0
0
0
0
20
1
1
5
1
0
0
0
1
0
0
0
0
20
1
1
5
1
0
0
1
4
0
1
4
0
0
7
4
2
1
0
0
0
7
4
2
1
0
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
10
10
16
14
10
0
0
0
10
10
16
14
10
0
0
0
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
?
?
?
?
?
?
?
?
?
?
?
?
?
?O@?he?
?@@@@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
?@@@@@@@h?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?@@@@@@?g?
?@@@@@@?g?
J(M?he?
7Yhf?
@@6Xhe?
@@@)X?h?
?I'@)Xh?
V4@1h?
?@h?
?@h?
?@h?
J5h?
?W.Yh?
?'6KO.Y?h?
?V4@0Yhe?
?
?
?
?
?
0: Video; 1: CbCr
0: Internal composite video signal; 1: From pin 2 input
0: Bypass OFF; 1: Bypass ON (used in Y/C mode)
0: Automatic mode (TV in operation); 1: Enforce killer ON when color control is min
0: TV in operation; 1: Test mode, killer circuit is not in operation
0 ~ 7 (-30dB ~ -40dB)
0 ~ 7 (Auto green off ~ level high)
0: Normal mode; 1: Tint control set center value (cann't control tint)
0: Easy to become NTSC; 1: Easy to become PAL
0~7
0: Normal mode; 1: VCO free run mode
0: FSC OUT; 1: EHT
0: PAL/NTSC/4.43 NTSC (AUTO); 1: PAL-M/PAL-N/NTSC(AUTO)
2: PAL; 3: PAL-M; 4: PAL-N; 5: NTSC; 6: 4.43NTSC; 7: Not available
0 ~ 15
0 ~ 15
0 ~ 31
0 ~ 31
0 ~ 15
0: Color ON; 1: Color OFF
0: Normal mode;1: VXO free run mode
0: Normal mode;1: VXO Standby mode

- 11 -
Remark
Unnecessary
0
0
0
0
0
?
?
?
?
?
?
?
?
?
?
?
?
?
W&h?
?W&@h?
W&@@h?
7Y@@h?
?J5?@@h?
W.Y?@@h?
?O.Ye@@h?
@@Y?e@@h?
@@@@@@@@@@g?
@@@@@@@@@@g?
@@h?
@@h?
@@h?
@@h?
@@h?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?O@?he?
?@@@@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
@?he?
?@@@@@@@h?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?@@@@@@?g?
?@@@@@@?g?
J(M?he?
7Yhf?
@@6Xhe?
@@@)X?h?
?I'@)Xh?
V4@1h?
?@h?
?@h?
?@h?
J5h?
?W.Yh?
?'6KO.Y?h?
?V4@0Yhe?
?
?
?
?
?
0
0
0
0
0
?
?
?
?
?
?
?
?
?
?
?
?
?
W&h?
?W&@h?
W&@@h?
7Y@@h?
?J5?@@h?
W.Y?@@h?
?O.Ye@@h?
@@Y?e@@h?
@@@@@@@@@@g?
@@@@@@@@@@g?
@@h?
@@h?
@@h?
@@h?
@@h?
?
?
?
?
?
SVC
SVC 07
Register
IF AGC
SVO SW
VIF SYS
V LEVEL
OM TYPE
OM SW
OM LEVEL
VCO FREQ
AMONI SW
AFT SENS
SVC 08
SVC 09
SVC 10
VCO ADJ
VIDEO SW
SYNC SS
DIntLace
OE TEST
Ext RB
Ext GB
Ext BB
Ext RDr
Ext GDr
Ext BDr
MONI C2
DDS BPF
BELL ADJ
BELL MONI
S KIL OPE
S KIL ON
S KIL OFF
BellBypas
Text Hpos
Text VPos
DE EM SW
CIK STOP
TEST MODE
MONI cbcr
IF TEST
DVD VOL
MAX VOL
CLPDEL50
CLPDEL60
CLPLEN
CLMPID
PIP H
Ch1 Pre
FM 2 Pre
NICAM Pre
MONO Pre
CH1 - M TH
CH1 - L TH
CH2 - M TH
CH2 - L TH
BERL
BERH
Range
0: Normal mode; 1: Minimize the gain of VIF amplifier
0: Internal Video out mode; 1: Selected External video output mode
0: 38.0 MHz; 1: 38.9MHz; 2: 39.5MHz; 3: 45.75MHz
0~7
0: APC Voltage sample holde circuit type; 1: APC detector stop type
0: Normal mode; 1: Over modulation measure circuit ON
0 ~ 15
0 ~ 255
0: Normal mode (de-empasis FM detector);
1: SAO mode at external audio input mode
0: 200KHz (4.5-0.5v change); 1: 150KHz (4.5-0.5v change)
2: 100KHz (4.5-0.5v change); 3:50KHz (4.5-0.5v change)
0: Internal; 1: External; 2: DVD-Y; 3: YC-Y
000: Low (sync tip side); 100: Middle (normal); 111: High (pedestal side)
0: Normal mode; 1: Deinterlace mode
Ext R Bias setting
Ext G Bias setting
Ext B Bias setting
Ext R Drive setting
Ext G Drive setting
Ext B Drive setting
DDS Band Pass Filter
Secam IC Only
Secam IC Only
Secam IC Only
Secam IC Only
Secam IC Only
Secam IC Only
Text Only
Text Only
0:Cut off freq. high; 1:Cut off freq. low
0:Normal; 1:IC Test Mode
0~7
0 ~ 100
0 ~ 100
0 ~ 31
0 ~ 31
1~3
1~3
0~255
0~49
0~49
0~49
0~49
0~143
0~255
0~143
0~255
0~255
0~255

- 12 -
Initial(PAL)
0
0
1
4
0
0
8
100
0
Initial(SECAM)
0
0
1
4
0
0
8
100
0
Remark
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
15
1
1
0
0
8
8
8
8
8
8
0
2
0
0
0
0
0
0
0
0
1
0
0
0
0
0
100
18
18
3
3
10
29
29
30
10
48
0
47
0
64
128
15
1
1
0
0
8
8
8
8
8
8
0
2
1
0
0
0
0
8
0
0
1
0
0
0
0
0
100
18
18
3
3
10
29
29
30
10
48
0
47
0
64
128
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
Unnecessary
TROUBLE SHOOTING
1. TV FUNCTIONAL
11100
TUNER / IF
12500
VIDEO/MICOM
13100
SOUND
18200
18100
SMPS
14400
HORZ. DEFL
15300
VERT. DEFL
16100
CPT
Secondary
SMPS Primary
2. TU / IF SECTION
11100
TUNER
11100
10
3
TUNER/IF
11101
11
(TU101)
11102
11104
11103
CONTROL SECTION
TUNER INPUT SECTION

5V(ZD102,C108,C106)
SDA(R514)
30V(C103,C107,ZD103,R150)
SCL(R516)
VIDEO/SOUND BUFFER
MOD. CONTROL SECTION
IF(Z111,C101,R100)
AGC(C110,R151,J108,R109
,R154,R108)
TUNER Not Working
TUNER Not Working
TU SEARCH Problem
TU SEARCH Problem
TUNING Problem
TU Weak Picture Signal
No Video Signal
No Sound Signal
TV system Detection Problem
Video S/N Problem
Sound S/N Problem
TV MODE Weak Picture Signal
Video Noise
No
Sound Noise
3. VIDEO PROCESSING
12511
12500 VIDEO/MICOM
R/C RECEIVER
PA01,R82,C30,C28,
In case of influx NOISE
12508
R/C is not operate
SOUND Section
11100
12510
LED O/P Section
TUNER
R501,R504,C502,C506,C507
LD11,R58,R60,R72,Q10
R154,C101,Z111
12509
R622,R621
NO SOUND
KEY I/P Section
NO CH. SEARCH
SW11~SW16
NO PICTURE
R16,R17,R18,R19,R20,R66
NO SOUND.
12507
R/G/B DRIVE Section
KEY Error
R505~R510, C510
12500
C510,C511,R515
35,36,40
50~64
NO PICTURE
61 ~ 64
31,32
AUDIO L/R
46~49
LV762XX
17~22
12506
DEFLECTION SECTION
R404,R512,R532,C512,C513
1~13
12502
REAR A/V
1 CHIP IC (IC501)
C515,C516,C517,C523,C544
04,09,35,4
DVD
12
41
Deflection Problem
9,62
Vertical/Horizontal Line
L IN: L221,C215
R IN: L222,C222
VIDEO
IN: L225,R226
DVD-Y,Pb,Pr
IN: C210,C211,C212
DVD-R
IN: L221,C215
DVD-L
IN: L222,C222
12505
12503
OSC SECTION (4.43MHz)
X501,
12504
RESET SECTION
R22,C15
R537
AUDIO/VIDEO No I/P, O/P
SET Maneuver
defectiveness
POWER SUPPLY SECTION

POWER
ST-5V(C521,R528)
RGB 9V(C510,C511,R515)
SET Maneuver
defectiveness
IF VCC(C528,C526,L528,C547)
VCC(C518,L503)
Clock Error
MENU Picture Error
SET Maneuver defectiveness
OSD Not Working
SET LATCH-UP
KEY Not Working No Sound
MENU Picture Error

- 13 -
4. SMPS PRIMARY SECTION

18200
18103
18105
BRIDGE RECTIFIER
NO POWER
NO STR VCCSUPPLY SO
NO POWER
FUSE OPEN & STR
DAMAGED DUE TO CHANGE
IN PRIMARY INDUCTANCE
OF SMPS
18110
VD801(TVR621D)
F801(T4AL250V)
NO POWER
POWER RADIATION
SAFETY PROBLEM
NO POWER
FUSE OPEN
NO RECTIFIER
DC O/P
18106
START RESISTOR
NO MICOM CONTROL
NO DEGAUSS
PURITY PROBLEM
IC801(STR-W6754)
SECONDARY LOAD REGULATION POOR
OVER VOLTAGE PROT. NOT OPR.
NO POWER / INTERMITANT NO POWER
SWITCHING NOISE
D815,R804,R805,R810,R839
STR NO OPR./NO POWER
EXCESSIVE I/P VOLTAGE CAUSES
NO POWER/ NO OSCILLATIONS
18111
18205
R804,R805
STR SWITCH ON PROB.
NO POWER
18108
STR VCC POWER SECTION
P801A/B,SW801
NO POWER
FUSE OPEN
18104
RELAY(DEGAUSS)
RL801,Q845,D847
TO
DEGAUSS
COIL
18101
AC INPUT
FUSE & VARISTOR
T802(150-F06T)
DB801(TS4B05G)
T803
18102
FILTER SECTION
STR FEED BACK SECTION

D845,R810,C840
LOAD REG. FB SECTION

IC802,Q840,R808,R853,C852
STR NO OPR./NO POWER

INTERMITENT NO POWER
SECONDARY O/P VOLTAGE POOR
INTERMITANT ST-BY MODE
SMPS SEC LOAD REG POOR

INTERMITANT NO POWER
5. SMPS SECONDARY SECTION

STRW6554
(S-Vcc)
17V
20V-(10W)
14V / 25mA
C831
(330u/25V)
D824
(SFAF504G)
(st-by 5V)
11V
D813
(RU3AMV)
ST_BY 1W
Option
KIA78L05BP
R873
(47/0.5W)
C826
(1000u/16V)
IC804
KIA78R09API
FBT
Trans
IC803 5V_1
KIA7805API
NT: 360mA
PAL:465mA
3.3V Reg.
1.5V Reg.
C540
(4.7u/250V)
LA78040N
(#2,Vcc)
D301
(RGP15J))
C309
(470u/35V)
112.17V / 395mA
110V
D826
(RU3AMV)
110.1V
R833
(RS 0.47/2W)
1.8V
9V
R513
(RS 300)
R529
(RS 68)
9V
R132
(RS 68)
9V
110.07V
L802
(82uH)
3.3V
LV76213(#62,#4 Vcc)
5.0V / 14mA
LA72730 (#8 Vcc)
5.0V / 40mA
LA72702N (#19 Vcc)

LA42102 (#5,St-by)
85mA
LC75024E (3.3V Vcc)
5V
145mA.
IC 501 (Main IC)

IC 751 (S/W IC )
IC 661 (RF STEREO NT)
IC 601 (SOUND-amp)
IC 807 (NICAM)
LC75024E (1.5V Vcc)

FM TX, Game, USB OPT
3.3V / 10mA
5.0V / 13mA
8.0V / 15mA
LV76213(#9, Vcc)
IC 501 (Main IC 3.3V Vcc)
LV76213(#20, Vcc)
IC 501 (Main IC Hor Vcc)
LV76213(#49,Vcc)
IC 501 (Main IC RGB Vcc)
5V /75mA.
TUNER(Vcc)
109.63V / 380mA (105V~120V)
FBT B+
FR403
(RF 1.2/2W)
29.97V / 10mA
C831
(220u/160V)

5.0V / 231mA
60mA
R520
(RS 620)
9V
28.2V / 320mA
EEPROM (#8, Vcc)
R620
(RS 5.6/2W)
CPT Board
26V
IC 601 (SOUND-amp) 10W+10W ST
D-Coil Relay
ST-5V
184.47V / 18mA
D505
(RGP10J))
LA42102N (#7,Vcc)
ST-5V
T/X Pre-Amp
NT: 398mA
PAL:503mA
180V
IC 601 (SOUND-amp) 5W+5 W ST
MAIN IC (#24, Vcc)
KIA78R05API
D806
(TVR06J)
IC 601 (SOUND-amp) 5W MONO
LA42102 (#7,Vcc)
IC04
IC806
C838
(2200u/25V)
SMPS
Trans
17V
LA42101 (#7,Vcc)
(28V~32V)
R107
(RS 12K/2W)
- 14 -
Tuner 30V
6. VERTICAL SECTION
15300
VERTICAL IC(IC301)
V-IN
PUMP
VVCC -UP GND OUT
O/STAGE
LA78141
15305
VERTICAL O/P DAMPING
& FILTER
R310,R315,C314,C305,C310
V-REF
15301
VERTICAL I/P
R305,R309,R311,C322
V
E
R
T
VERTICAL FOLDING
VERTICAL ROLLING NOISE
(HORZ LINE MOVING UP/DOWN)
VCT VERTICAL O/P

RETRACE KINE
VERT SIZE PROBLEM
VERT IC O/P CAN DECIDE
GAIN
D
Y
15306
VETICAL REFERECE SECTION
C313,C322
VERT SIZE PROBLEM
VERT LINEARITY PROBLEM
POWER OFF(PROTECTION ENABLED)
15303
VCC SECTION (24V)
FR301,D301,C303,C309,C306
15308
15304
PUMP UP VCC
C307,D302
FBT SEC O/P VCC

FULL RASTER
VERT. PROTECTION ENABLE
CAUSES NO POWER
OUTPUT STAGE VCC SECTION
C307
VCT VERT. PROTECTION
ENABLE
POWER OFF
RETRACE LINE
POWER OFF
7. HORIZONTAL SECTION
14401
H-OUT
HORZ DRIVE SECTION
R403,R401,
47V VCC
Q401,T403,C404
DEFLECTI0N PROB
POWER OFF
14404
14402
HORZ. DEF
HORZ O/P SECTION
COMPENSATION SECTION
H
O
R
Q402,C414
C412 ,L401,L402,
DEFLECTION PROB
INEARITY ADJ NOT WORK
POWER OFF
STRANGE NOISE
HORZ SIZE PROBLEM
STRANGE NOISE
COLLECTOR
14410
HEATER
VOLTAGE
.FR401
X-RAY WORKING
SAFETY PROB
ROLLING PICT
180V VOLTAGE
FBT
T402
FR501,D505,C540
HORZ LINE
NO RETRACE
26V VOL
MAIN VCC(110V)
FR301,D301
ANODE
FOCUS
SCREEN

- 15 -
8. SOUND PROCESSING SECTION

ANT.
Speaker
11500
TUNER
12500
1 CHIP IC
NICAM IC
(LV762XX)
(LC75024E)
13603
11100
Sound Amp.
13602
LA42102L(10W*2))
TUNER : RF signal is feed to TUNER through Antenna. IF output from Tuner is then given to 1 CHIP IC.
1 CHIP IC : 1 CHIP IC processes the input IF. Demodulates Picture and sound information and gives analog R G B
output for Display and SPKL/R as audio output, this sound output is further Amplified and feed to speakers.
Sound Amp : Sound amps(LA42102L) is and Audio Amplifier it amplifies the output sound signal from
Surround ic(LC75024E) and feeds to speaker which generates Sound.
9. CPT DRIVE SECTION

16100
CPT Board Circuit 11700
R G B AMP CIRCUIT
16101
L901
180V
R917
R923
R912
L902
R
Q901
The CPT-BOARD assembly is composed of discrete type RGB

Amplifier.
Q903
Amp- Gain is defined by Resistance of R917, R912,R923.
High Frequency compensation is made by inductance of L901,
L903
capacitance of C907,C904 and C902.
R915
DC level of emitter of Q901,Q902 and Q903 is defined by R908.
R916
C907
Q902
B
R906
L904
R905
R921
C902
9V
C904
R908
R922
D902
11500
VIDEO PROCESSING
SECTION
16101
R,G,B Signal-IN
L902, L903, L904
180V
R
16100
16002
CPT CIRCUIT VCC / GND
1 Vcc 180V 5 GND
9V
16004
DISCHARGE
PROTECTION CIRCUIT
L901
ONE SIGNAL R/G/B)

MISSING
NO PICTURE, CPT
Dead
L902
Q901
ONE SIGNAL (R/G/B)

MISSING
CPT DRIVE
SECTION
L903
R915
L904
R916
C907
R905
CPT / e-GUN
Q902
R906
>
>
>
R921
C902
C904 R922
R908
D902
16005
Spot Killer CIRCUIT
C901, R902, D903
SPOT & TRAY

- 16 -
17006
Heater Voltage
FR932
e-GUN Dead
e-GUN LIFE
DECREASE
5.1V
IC804
From
9V
10
SCL
SDA
33V
5V
IF
SAW
SAW
SPK1.
18
3,6 11
HIC291
01+ '
Audio(Game)
Video(Game)
out
9V
RGB
49
46~48
33
SCART
SCART
R,G,
JA01
ST-5V
24C04/16
EEPROM
IC02
SDA SCL
(FLAT
(FLAT OPT.)
OPT.)
EW IN
16
EW-OUT
31 32
DVD
DVD
10 11 13
Y(G)/Cr(R)/Cb(B)
LA76213
LA76213
22
17
H-OUT
5V
Vcc
5V
3.3V
VDD
H-Vcc
IF
5V
USOC
OUT
RGB
24
19
62
From
IC803 IC804 IC804 IC04
9v
From
IC804
9v
From
5v
From
9v
From
64 61
(( PHONE)
PHONE)
ST-5v
7.5V
7.5V
5V
5V
IC804
Monitor V OUT(ST)
R620
R620
IC803
IC803
9v
From
Rear_AV(1)
Rear_AV(1)
56
IF IN
57
TV IN(ST)
54
OUT
SIF
SPK L/R
50
EXT
Video-in
IN
R/L Out
Ext R/L
19 20
SCL
SDA
51
21
15
9
14
AV1(V/R/L)-IN
(STEREO
(STEREO Opt)
Opt)
IC751
IC751 LA72730
LA72730
SIF IN
24
23
SPK2.
Game
Game Pack(Game
Pack(Game Opt)
Opt)
4,5,6
From USOC
TUNER
Z102
12
SDA SCL
27 26
LC75024E
A2/NICAM
IC661
17 18
LIN-TV
LA72702
BTSC
IC701
SDA SCL
R-OUT
L-OUT
RIN-TV
SOUND
SOUND AMP.
AMP.
LA42102(N)
LA42102(N)
Sound
Sound Max
Max
STEREO,
STEREO,
LA42101
LA42101
(Mono)
SOUND
SOUND AMP
AMP
V-OUT (Mono)
MONO
MONO
M L-OUT
CPT DRIVE
FB
IIC Bus Line
ID
- 17 AV

M_R/L OUT(ST)
Option Par
t
EW OUT
HDT
L401
AC
AUDIO B+
(100~240V)
INPUT
14
(110/115V)
B+
10.5V
STEREO
( ~ A43L)
MONO
( ~A43K )
TRANS
SMPS
(17V/11V)
MD1803
Q402
Collector
HEATER
9
B+
ABL
AFC
8
12
V_DY
FBT
185V
2
24V
5V
5V
SOUND
SOUND
10
FBP in
IC401
Vcc
TDA8145
V-in
V-OUT
IC301
5V
R610
9V REG
IC804
ST-5V REG
IC04
(1W Opt)
TRANS
ST-BY
BLOCK DIAGRAM
PRINTED CIRCUIT BOARD

MAIN

- 18 -
CPT (option)

- 19 -
EXPLODED VIEW
IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics.These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION,Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
943
400
170
913
150
510
(option)
174
105
112
120
520
300
330
320
310

- 20 -
P/NO.:3854VA0196D (08.04.14)
SVC. SHEET : 3854VA0196D-S

LG 21fu7rl Chasis CW81B PDF

Uploaded by

Copyright:

Available Formats

LG 21fu7rl Chasis CW81B PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG 21fu7rl Chasis CW81B PDF

Uploaded by

Copyright:

Available Formats

Internal Use Only

Copyright2008 LG Electronics.Inc. All right reserved.

LGE Internal Use Only

Before returning the receiver to the customer,

An isolation Transformer should always be used during the

always perform an AC leakage current check on the exposed

Leakage Current Cold Check(Antenna Cold Check)

To determine the presence of high voltage, use an accurate high

With the instrument AC plug removed from AC source, connect an

Leakage Current Hot Check (See below Figure)

Leakage Current Hot Check circuit

Good Earth Ground

LGE Internal Use Only

5) The receiver must be operated for about 20 minutes prior to

Requirement for Test

T4/Z4 Model PAL Model

Safety: CB Spec. (EN60065)

PAL BG, DK, I / NTSC M (AV 3.58/ 4.43)

China/ Indonesia/ Thai/ Vietnam

PAL BG, DK, I / NTSC M (AV 3.58/ 4.43)

L America/ Philippines/ Taiwan

PAL BG, DK, I / NTSC M (AV 3.58/ 4.43)

Asia/Middle East/ Africa

SECAM BG, DK, L

AC100 ~ 240V, 50/60Hz

Korea, Latin America, China, Indonesia,

14 ~ 21 inch (FLAT / Conventional)

1) Temp : -20 ~ 60 deg

Copyright2008 LG Electronics.Inc. All right reserved.

LGE Internal Use Only

Tool Option (For China, Vietnam,Thai,CIS)

Input (For component)

Power, Vol(F, G), PR(E, D), MENU, OK

System/ Storage/ Normal/ Turbo

Storage/ System/ Channel/ Fine/ Search/ Name

Copy/ Move/ Delete/ Skip

Dynamic/ Standard/ Mild/ Game/ User

Contrast/ Brightness/ Color Sharpness

Tint: NTSC System only

Tint (NTSC-M Only)

Flat/ Music/ Movie/ Speech/ User

AV, RF Stereo Option

Option For Middle East Aisa/Africa

Wide Range (191ch)

-- : -- Pr 1 VOL 30 Off (On)

Auto off (Sleep)

(Sleep) For Middle East Asia/Africa

English/ Indonesia/ Thai/ Vietnam

TV/ AV1/ AV2/ Component

Copyright2008 LG Electronics.Inc. All right reserved.

LGE Internal Use Only

4. Screen Voltage Adjustment

These instructions are applied to CW81B Chassis.

4-1. Adjustment (Using Factory Remote Control)

5. Purity and Convergence Adjustment

3. AGC Voltage Adjustment

3-2. Adjustment Preparation

6) Pull the DY slowly backward and fix it when the whole

5-2. Convergency Adjustment