ROCK-EVAL 6 APPLICATIONS

IN HYDROCARBON EXPLORATION, PRODUCTION

AND IN SOIL CONTAMINATION STUDIES
In Revue de l'Institut Franais du Ptrole, VOL. 53, N 4, p. 421 - p. 437

E. Lafargue, J. Espitali, F. Marquis and D. Pillot


Institut Franais du Ptrole, 1-4 Av. de Bois Prau, 92852 Rueil-Malmaison, France

The RockEval 6 is marketed by VINCI TECHNOLOGIES Parc de lile- 27B rue du Port- 92022 Nanterre cedex - France
Tel: +33 (0)1 41 37 92 20 - Fax: +33 (0)1 41 37 04 76 - E.Mail : [email protected]

Abstracts

Successful petroleum exploration relies on detailed analysis of the petroleum system in a given area.
Identification of potential source rocks, their maturity and kinetic parameters, and their regional distribution
is best accomplished by rapid screening of rock samples (cores and/or cuttings) using the Rock-Eval
apparatus. The technique has been routinely used for about fifteen years and has become a standard tool for
hydrocarbon exploration. This paper describes how the new functionalities of the latest version of Rock-
Eval apparatus (Rock-Eval 6) have expanded applications of the method in petroleum geoscience.
Examples of new applications are illustrated for source rock characterization, reservoir geochemistry and
environmental studies, including quantification and typing of hydrocarbons in contaminated soils.
Keywords: Rock-Eval ; source rock characterization ; reservoir geochemistry ; soil contamination


CONTENT:
1. INTRODUCTION 2
2. METHODOLOGY: ROCK EVAL 6 NEW FUNCTIONALITIES 2
2.1. NEW TEMPERATURE RANGE FOR THE PYROLYSIS AND OXIDATION OVENS 2
2.2. CONTINUOUS ON-LINE DETECTION OF CO AND CO
2
WITH INFRA-RED DETECTORS 2
2.3. PROCESSING OF MULTI-HEATING RATES CYCLES 3
3. RESULTS 3
3.1. MINERAL CARBON DETERMINATION 3
3.2. ORGANIC CARBON DETERMINATION 3
3.3. OXYGEN INDEX DETERMINATION 4
3.4. RESIDUAL PETROLEUM POTENTIAL (S2) AND HIGH TEMPERATURE TMAX 4
4. ROCK EVAL 6 ENLARGED APPLICATIONS 6
4.1. RESERVOIR GEOCHEMISTRY 6
4.2. SOIL CONTAMINATION STUDIES 6
5. CONCLUSIONS 7
6. REFERENCES 7







2 / 23
1. INTRODUCTION
The characterization of the organic matter from
sedimentary rocks is one of the main objectives of organic
geochemistry and is now widely recognized as a critical
step in the evaluation of the hydrocarbon potential of a
prospect. During the last two decades, various authors
(e.g., Barker, 1974; Claypool and Reed, 1976; Espitali et
al., 1977 and 1984; Clementz et al., 1979; Larter and
Douglas, 1980; Horsfield, 1985; Peters and Simoneit, 1982;
Peters, 1986) have used pyrolysis methods to provide data
on the potential, maturity and type of the source rocks in
different sedimentary basins.
Among these techniques, Rock-Eval pyrolysis has
been widely used in the industry as a standard method in
petroleum exploration. This technique consists in the
temperature programmed heating of a small amount of rock
(100mg) in an inert atmosphere (Helium or Nitrogen) so as
to determine (Fig. 1): the quantity of free hydrocarbons
present in the sample (S1 peak) and the amount of
hydrocarbons and oxygen containing compounds (CO
2
)
that are produced during the thermal cracking of the
insoluble organic matter (kerogen) in the rock (S2 and S3
peaks respectively peak). Furthermore, the Total Organic
Carbon (TOC) content of the rock is determined by
oxidation under air, in a second oven, of the residual
organic carbon after pyrolysis (S4 peak). The method has
not evolved much over the years. However, the new Rock-
Eval 6 apparatus incorporates major changes in the
methodology. As a consequence, new scientific
applications of the method are proposed.
As we will see in the following, some of these
applications are new and therefore expand the fields of use
of the Rock-Eval methodology, while others are mainly
improvements of the existing method. In this respect, we
will first present the Rock-Eval 6 functionalities and we
will then detail their different applications (use of mineral
carbon determination in carbonate sequences, application of
new Oxygen Indices, application of high temperature Tmax
(temperature measured at the top of the S2 peak), and use
of the improved total organic carbon (TOC) determination).
Finally, we will illustrate more specific applications of
Rock-Eval 6 data in reservoir geochemistry and in soil
contamination studies.
2. METHODOLOGY: ROCK EVAL 6 NEW
FUNCTIONALITIES
A number of technical changes have been
introduced in the Rock-Eval 6. They lead to the new
functionalities described in the next paragraphs.
2.1. NEW TEMPERATURE RANGE FOR THE
PYROLYSIS AND OXIDATION OVENS
In Rock-Eval 6, programmed heating of both the
pyrolysis and the oxidation ovens is conducted from 100C
(instead of 180C in the previous versions) up to 850C
(instead of 600C in the previous versions).
Pyrolysis at high temperatures up to 850C is
necessary for complete thermal degradation of terrestrial
type III organic matter. Previous studies have shown that
thermal cracking of terrestrial organic matter is not always
complete at 600C and therefore the corresponding S2 peak
can be underestimated. The consequence is a possible
underestimation of the petroleum potential for type III
source rocks. By increasing the maximum pyrolysis
temperature in Rock-Eval 6, the measure of the Hydrogen
Index (HI = S2/TOC) is more accurate and the range of
validity of Tmax is extended to higher values.
Another important outcome of this new functionality
is a better kinetic parameters determination for type III
organic matter. For such samples, we commonly observed
pyrolysis curves that did not return to the baseline when
using the low heating rates. This experimental problem
was a source of uncertainty in the determination of the
kinetic parameters for type III source rocks.
The temperature of oxidation of the sample has also
been increased (up to 850C) in order to avoid incomplete
combustion of refractory material, such as heavy oils, tar-
mats, coke or pyrobitumen in source rocks or reservoir
rocks, or polyaromatic hydrocarbons (PAH) in soils from
polluted sites. This new functionality has resulted in a
better TOC determination. As we will see later, high
temperature oxidation also allows mineral carbon
determination, which is one of the main improvements
provided by the Rock-Eval 6.
The initial pyrolysis temperature has been reduced
to 100C instead of 180C to allow detailed study of the
free hydrocarbons in rocks. This is particularly useful for
the analysis of cuttings on site (oil shows during drilling),
for reservoir studies (better evaluation of API gravity from
Rock-Eval data) and especially for soil contamination
studies where numerous contaminants are very light
hydrocarbon compounds (gasoline, diesel oil, jet fuel). In
conjunction with this lower temperature, it is now possible
to select the temperature program in order to optimize the
separation of these light compounds, thus approaching a
separation according to bubble points.
Furthermore, the location of the thermocouple
driving the ovens has been changed. In Rock-Eval 6, the
thermocouple is now located in the crucible immediately
below the sample (Fig. 2) instead of against the oven wall
as it was in Rock-Eval 2. Therefore the measured
temperature is very close to the real sample temperature.
As a result, the temperature measurement is more accurate.
As illustrated in Figure 2, the shape of the crucible has also
been changed in order to accommodate the thermocouple
(TC1). The second thermocouple (TC2) is used to ensure
continuity of temperature control when the crucible is
removed from the pyrolysis oven at the end of the analysis.
The same is true for the oxidation oven.
2.2. CONTINUOUS ON-LINE DETECTION OF CO
AND CO
2
WITH INFRA-RED DETECTORS
For earlier versions of the Rock-Eval instrument, the
CO
2
released during pyrolysis was trapped and quantified
using a catharometer. Although the S3 peak quantifies the
total CO
2
yield, it does not reflect its temperature
programmed release during kerogen cracking. This limits
interpretation of the S3 response. Similarly during
oxidation, the CO
2
released was trapped at 600C and then
quantified by the catharometer. For practical reasons, CO
was not analyzed during pyrolysis or oxidation.
These limitations have led us to introduce sensitive
infrared detectors into the Rock-Eval 6, that are capable of
continuous on-line recording of the amount of both CO and
CO
2
released during pyrolysis and oxidation of samples. As
a result, five characteristic curves are obtained for each
sample analyzed using Rock-Eval 6 (Fig. 3): (1) the amount
of hydrocarbons (Flame Ionization Detector, FID trace of
S1 and S2 peaks), (2-3) CO and CO
2
produced during

3 / 23
pyrolysis (CO and CO
2
pyrolysis curves), (4-5) CO and
CO
2
produced during oxidation (CO and CO
2
oxidation
curves). The sixth curve in Figure 3 is the superposition of
CO and CO
2
curves and is very useful for a rapid
visualization of the presence or absence of carbonate in the
sample.
As we will see in the results that follow, the
continuous recording of both CO and CO
2
has brought a
number of new useful parameters. For instance, the
character of CO and CO
2
pyrograms produced can be used
to distinguish the types of kerogen in rock samples. The
different peaks on the pyrograms represent different classes
of functional groups containing oxygen (e.g. ethers,
carboxyls, carbonyls) which vary from one organic matter
type to another. This approach was successfully used
earlier for CO pyrograms from immature to early mature
source rocks (Daly and Peters, 1982). This new
functionality allows measurement of the mineral carbon in
the rock in addition to the classical organic carbon
determination. Furthermore, mineral type determination
(e.g., calcite, dolomite, siderite) is possible.
2.3. PROCESSING OF MULTI-HEATING RATES
CYCLES
Because of new applications of the Rock-Eval
methodology to reservoir geochemistry and soil
contamination studies, it was necessary to allow enough
flexibility in the machine to account for the variety and the
specificity of the hydrocarbons to be detected and
quantified. For example, in soil contamination studies, the
residence time of the S1 peak and the starting heating rates
are critical for a good determination of pollutants. For
Rock-Eval 6, there is now a true Temperature versus
Time function, meaning that initial temperatures, heating
rates and residence times can be adjusted by the user for
any specific application. In addition, a number of pre-
programmed cycles are available that have already been
successfully tested for soil contamination studies and for
reservoir geochemistry (e.g., detection of tar-mats).
3. RESULTS

3.1. MINERAL CARBON DETERMINATION
The amount of mineral carbon is calculated by
addition of the CO
2
released during pyrolysis above 400C
and the CO
2
from carbonate decomposition during the
oxidation phase from 650C to 850C (Fig. 4). Carbonate
minerals such as magnesite and siderite start to be
decomposed when the pyrolysis temperature approaches
400C whereas dolomite and calcite (the most important
minerals in carbonate sequences) decompose during
oxidation (Fig. 5). On this figure, we see that dolomite
oxidative decomposition gives two characteristic peaks
corresponding to the following reactions:
(1) CaMg(CO
3
)
2
----> CaCO
3
+ MgO + CO
2

(2) CaCO
3
----> CaO + CO
2
at higher temperature
Calcite decomposition occurs at about 800C and is
recorded by a single peak.
Because of this sequential decomposition of the
carbonate minerals during the analytical cycle, it is possible
to quantify the amount of mineral carbon and estimate
which species is dominant in the sample.
Even though it is less abundant than calcite and
dolomite, siderite is quite common in source rocks,
particularly in fermentation zones where the preservation of
organic matter is enhanced (Curtis, 1977; Berner, 1981).
Its range of decomposition temperature is large, from
400C to 650C, and therefore it can interfere, during
pyrolysis, with the CO
2
released by the oxygenated
functions in the organic matter. In Rock-Eval 6, thanks to
the continuous on-line recording of CO and CO
2
released
during pyrolysis, it seems that the combination of S3CO,
S3CO
2
values and Tpeak CO
2
(temperature at the
maximum of CO
2
pyrolysis curve; "Tmax CO
2
") on bulk
rocks can point out very rapidly when and where siderite is
occurring. Samples with siderite present S3CO values
greater than 5mgCO/g rock; S3CO
2
greater than
10mgCO
2
/g rock and Tpeak CO
2
in the 485-520C
temperature range. As a result, we get access to a very
good indicator of the presence of siderite in source rock
samples which in turn may be used as a redox indicator of
the whole series (siderite is occurring only under specific
environment). Furthermore, the comparison of a series of
bulk rocks and acid-treated rocks indicated that, when there
is a lot of siderite, we can observe the production of CO
during pyrolysis according to the following set of chemical
reactions:
(1) FeCO
3
---> FeO + CO
2

(2) 3 FeO + CO
2
----> Fe
3
O
4
+ CO
Once siderite is removed by acid treatment, the
CO production stops which results in small values of
S3CO (organic CO alone).
Mineral carbon content based on Rock-Eval 6
analysis correlates well with that obtained by routine
chemical attack technique throughout the range observed in
most sedimentary rocks (0-12%; Fig. 6).
This rapid estimate of both the organic and mineral
carbon is very useful in studies of the relationship between
organic matter and mineral carbon in carbonate petroleum
systems. Such work has been successfully conducted
recently by Van Buchem et al. (1996) on the Upper
Devonian mixed carbonate-siliciclastic system of western
Canada. These authors show a distinct pattern in plots of
the carbonate versus organic carbon content within each
sequence, each being characteristic of the equilibrium
between carbonate precipitation, organic matter dilution,
and occurrence of dysaerobic conditions.
3.2. ORGANIC CARBON DETERMINATION
Like previous Rock-Eval systems, RockEval 6
determines the amount of organic carbon by adding
pyrolyzed carbon (PC) and residual carbon (RC).
Nevertheless, the continuous CO and CO
2
detection has
improved PC and RC quantifications (Fig. 7).
The pyrolyzed carbon is computed from: (1) the
hydrocarbon compounds released in peaks S1 and S2,
assuming that they contain about 83% of organic carbon,
(2) the CO released during pyrolysis up to 500C (S3CO
peak) and (3) the CO
2
released during pyrolysis up to
400C (S3CO
2
a peak). To avoid interference by release of
pyrolytic CO
2
from carbonate minerals such as siderite,
only the first part of the CO
2
pyrolysis curve is taken into
account. Likewise, in order to avoid possible interference
caused by Boudouard's reaction, where the CO
2
released
early during carbonate decomposition can react with the
residual carbon to produce CO (CO
2
+ C --> 2 CO), we

4 / 23
limit the calculation for CO to a temperature of 500C. The
residual carbon is obtained during the oxidation phase by
summing the organic carbon oxidized into CO (S4CO
peak) and CO
2
up to 650C (S4CO
2
peak). At higher
temperatures, there is no more CO production and the CO
2

comes generally from the decomposition of carbonates.
The progresses made in organic carbon
determination have brought higher performances as a
whole (Fig. 8; comparison between TOC measurements
using Rock-Eval 6 and LECO), but this is particularly true
when dealing with coal samples where Rock-Eval 2
response was often poor. The organic carbon measured
now for mature coal samples (Vitrinite Reflectance (Ro) >
2%) is drastically improved since high temperature
oxidation allows a complete combustion of the organic
matter, thus providing the true residual carbon in the
sample (Fig. 9).
3.3. OXYGEN INDEX DETERMINATION
In the previous Rock-Eval apparatus, the Oxygen
Index (OI in mgCO
2
/g TOC) is calculated from the amount
of CO
2
released and trapped over the 300C to 390C
pyrolysis range. For the Rock-Eval 6 instrument, both CO
and CO
2
are continuously monitored during the
programmed pyrolysis of a rock sample. From these
curves, Oxygen Indices specific to CO
2
(OICO
2
) and for CO
(OICO) can be defined (Fig. 10). The combination of these
two values gives the true Oxygen Index (OI
RE6
).
This improvement in the calculation of the Oxygen
Index allows the use of the OICO
2
/OICO ratio and the OI
RE6
,
to estimate changes during source rock deposition. For
instance, on a series of source rock samples from the
Bucomazi formation (Fig. 11), we were able to differentiate
between "basin fill" versus "sheet drape" geological
assemblages where the organo-facies variations depend
upon paleoenvironment of deposition (Lafargue and
Burwood, 1997). These differences were also illustrated by
the CO and CO
2
pyrolysis curves that vary from one
depositional environment to the other thus indicating
variations in the chemical composition of the organic
matter (Fig. 12).
This modification of the apparatus improves its
application toward studies of organic facies variation in
recent sediments, where the organic matter is rich in
oxygenated functions.
3.4. RESIDUAL PETROLEUM POTENTIAL (S2)
AND HIGH TEMPERATURE TMAX
For Rock-Eval 6, the final pyrolysis temperature is
850C instead of 600C. As a consequence, the petroleum
potential of many type III rock samples is increased and the
resulting Hydrogen Index is more representative. Another
improvement of this high temperature pyrolysis is the
ability to measure high Tmax values for type III samples
with vitrinite reflectance values (Ro) greater than 2%.
Figure 13 shows differences between the S2 peaks obtained
by Rock-Eval 2 and Rock-Eval 6 for coal samples with a
large range of maturities. The figure shows that the value
of S2 changes significantly and that Tmax values over
600C are significant and are not an artifact of the
measurement caused by very small S2 peaks. The
correlation between Tmax and Ro (Fig. 14) is thus
extended to the very mature samples, which was not
possible with the previous apparatus.
In type III source rocks, small residual potential S2
makes it difficult to know whether there is still remaining
gas potential. When such source rocks are located in
thrusted zones, it is very important to determine their
relative maturities in different parts of the thrust in order to
reconstruct the kinematics of deformation of the basin.
This reconstruction requires maturity measurements that
where difficult to obtain with previous Rock-Eval
apparatus when the samples were highly mature. In
addition, determination of the residual potential for gas and
the role of coal maturity on its retention properties is also of
interest for the evaluation of coal bed methane (Scott et al.,
1994).


5 / 23




Example of a complete
Rock-Eval 6 analysis
of crude rock.

The pyrolysable
carbon is computed
from S1, S2, S3co and
S3co2 residual carbon
(RC) from S4co and
S4co2 and mineral
carbon (MINC) from
S5 and S3MINC.

The TOC is calculated
by taking the sum of
the Pyrolysable carbon
(PC) and the residual
carbon (RC).

6 / 23
4. ROCK EVAL 6 ENLARGED APPLICATIONS
This section describes how the new functionalities
of the Rock-Eval 6 expand applications of the method in
reservoir geochemistry and in soil contamination studies.
4.1. RESERVOIR GEOCHEMISTRY
Geochemistry of reservoirs is an area of growing
interest with a remarkable economic importance because it
can be used to evaluate reservoir continuity during field
appraisal, to identify non-productive reservoir zones, and to
analyze commingled oils for production allocation
calculations (e.g., Kauffman, 1990; England and Cubitt,
1995). The Rock-Eval method has already been
successfully applied in reservoir geochemistry, especially
for the detection of tar-mats and for the prediction of oil
API gravities (Trabelsi et al., 1994). For reservoir
geochemistry, the main advantages of Rock-Eval 6 are the
capability to perform both pyrolysis and oxidation of the
sample up to 850C at various rates.
Figure 15 is an example of Rock-Eval 6 results for
four different reservoir rocks: three sandstones and one
carbonate. The first sample represents a conventional oil
accumulation that produces a large S1 peak and a smaller
S2 peak. Almost no CO and CO
2
are generated during
oxidation.
The second sample shows a small S1 peak, a
bimodal S2 peak (small S2a and large S2b) and significant
amounts of CO and CO
2
released during the oxidation.
This sample is from a conventional tar-mat, i.e. a reservoir
rock accumulated with crude oil enriched in resins and
asphaltenes. For the last sandstone reservoir, we still
observe the S1, S2a and S2b peaks but we also observe an
important CO
2
peak produced during oxidation at high
temperature (near 800C). Since we also observed this
peak in the rock sample after decarbonatation, it cannot be
caused by carbonate decomposition of minerals in the
sandstone matrix. This peak corresponds to the combustion
of refractory material associated with pyrobitumen in the
sample. Therefore it seems possible, from the comparison
of the oxidation curves of two tar-mat levels, to distinguish
a conventional tar-mat deposited in the reservoir from a
pyrobitumen produced by in-place secondary cracking of
an oil accumulation. This distinction is very important
since it can guide exploration and production strategies in
oil fields with tar-mats.
The carbonate reservoir sample shows the same
pattern in the FID trace as that observed for the
conventional tar-mat in the sandstone reservoir. This is
typical of the high amounts of resins and asphaltenes
present in the rock. During the oxidation phase of the
sample, the strong CO
2
production at about 500C and the
CO production correspond to the residual organic carbon,
whereas the very high amount of CO
2
produced at higher
temperature corresponds to the decomposition of the
carbonate matrix.
4.2. SOIL CONTAMINATION STUDIES
Due to its economic, environmental and industrial
importance, the characterization of soils contaminated by
hydrocarbons is another area where research is very active.
Rock-Eval 6 expands the application of pyrolysis
methodology to oil-contaminated sites due to the possibility
of starting the analysis at low temperature (100C).
Furthermore, heating rates can be adjusted so as to release
the different petroleum cuts (e.g., gasoline, diesel oil, heavy
oils, lubricant oils, gas plant distillation residues). For this
application a specific pyrolyser called Pollut-Eval with
cooled autosampler has been developed in order to reduces
the loss of light compounds. The vaporized hydrocarbons
are identified by the FID and the signal is integrated for full
quantification. A complete carbon mass balance is then
carried out through oxidation of the residue and continuous
quantification of CO and CO
2
by the infrared detectors.
The equipment thus provides the parameters needed
to characterize a contaminated site: what pollutant, how
much and where. Due to the short duration of the analysis
(30 min.), the time needed to evaluate the extent of a
contaminated site is drastically decreased compared to
routine techniques that involved the extraction of the
pollutant prior to its analysis by chromatography, infrared
or chromatography-mass spectrometry. Furthermore, when
used on site, the measurements can be used to optimize the
drilling program (Ducreux et al., 1997).



This pyrogram shows the
superposition of curves
obtained with the Pollut-
Eval for gasoline, kerosene,
diesel-oil and sewage-oil.

To identify the pollutant, we
use the relative value
(identified by the letter R and
numbered from 0 to 3) of the
hydrocarbon amount
measured in each pre-
defined integration area.

The relative values
corresponding to each
pyrogram are :
- Gasoline : R0 = 93%
- Kerosene : R1 = 81%
- Diesel-oil : R2 = 74%
- Sewage-oil : R3 = 75%


7 / 23
Pollut-Eval data can be correlated to standard
environmental data such as infrared response. Pollut-Eval
data are complementary to infrared or gas chromatographic
analyses because they allow rapid screening of a large
number of samples, thus helping to identify the samples
worthy of additional study. An example of the application
of Rock-Eval 6 data for two industrial sites is presented in
Figure 16. The upper part of the figure shows
contamination by diesel oil and polyaromatic hydrocarbons
in a soil near an old gas plant. The FID trace indicates two
main peaks corresponding to the mixture of these
hydrocarbons and the CO and CO
2
traces during oxidation
are characteristic of the combustion of the heavy residue
accompanying these products in the pollution. The second
example is taken from contaminated soil near a service
station. Light gasoline-range compounds are released early
during pyrolysis and no significant amounts of CO and CO
2

are recorded during oxidation.
5. CONCLUSIONS
The new Rock-Eval 6 pyroanalyzer marks an
important step in the development of programmed pyrolysis
systems. This apparatus provides new functionalities and
parameters that expand applications of the technique in
petroleum geoscience. Problems related to the older Rock-
Eval systems have been ameliorated. The major
improvements and their scientific impact can be
summarized as follows:
- Mineral carbon determination:
-> improved characterization of marly/carbonate
source rocks
-> detection of carbonate types (e.g., siderite,
calcite, dolomite)
-> enhanced characterization of hydrocarbons in
carbonate reservoirs
-> possible correction of matrix effects
- Oxygen indices:
-> impact on source rocks facies analysis
-> impact on the knowledge of source rocks
preservation conditions
- Improved measurements of TOC and Tmax:
-> better analysis of type III source rocks
-> better analysis of heavy bitumen in reservoirs
(tar-mat studies)
-> better characterization of coals
Acknowledgments
The support granted by the European Community (Thermie
Project OG/0146/93) for this project is greatly appreciated. We
also wish to thank A.Y. Huc, A. Mascle and K. Peters for their
very helpful review of a preliminary version of the manuscript.
6. REFERENCES
BARKER, C. 1974. Pyrolysis techniques for source rock
evaluation. Amer. Assoc. Pet. Geol. Bull., 58, 2349-2361.
BERNER, R.A. 1981. A new geochemical classification of
sedimentary environments. J. Sed. Petrol. 51, 359-365.
CLAYPOOL, G.E. and REED, P.R. 1976. Thermal analysis
technique for source rock evaluation: Quantitative estimate of
organic richness and effects of lithologic variation. Amer. Assoc.
Pet. Geol. Bull., 60, 608-626.
CLEMENTZ, D.M., DEMAISON G.J. and DALY A.R., 1979.
Well site geochemistry by programmed pyrolysis. Proceedings
of the 11th Annual Offshore Technology Conference, Houston,
OTC 3410, v.1, 465-470
CURTIS, C.D. 1977. Sedimentary geochemistry: environments
and processes dominated by involvement of an aqueous phase.
Phil. Trans. R. Soc. London. A.., 286, 353-372.
DALY, A.R. and PETERS K.E. 1982. Continuous detection of
pyrolytic carbon monoxide: A rapid method for determining
sedimentary organic facies. Amer. Assoc. Pet. Geol. Bull., 66,
2672-2681.
DUCREUX, J., LAFARGUE E., MARQUIS, F., PILLOT, D.
and BOCARD, C. 1997. Use of Rock-Eval method for the
evaluation of soils contaminated by hydrocarbons. Analusis, 25,
n 9-10, 40-44.
ENGLAND, W. and CUBITT, J. 1995. The Geochemistry of
Reservoirs. Geol. Soc. Sp. Publ., 86.
ESPITALIE, J., LAPORTE, J.L., MADEC, M., MARQUIS, F.,
LEPLAT, P. and PAULET, J. 1977. Mthode rapide de
caractrisation des roches mres, de leur potentiel ptrolier et de
leur degr dvolution. Rev. Inst. Fr. Petr., 32, 23-45.
ESPITALIE, J., MARQUIS, F., and BARSONY, I. 1984.
Geochemical logging. In: Analytical pyrolysis- Techniques and
applications, K.J. Voorhees ed., Boston, Butterworth, 276-304.
HORSFIELD, B. 1985. Pyrolysis studies in petroleum
exploration. In: Advances in Petroleum Geochemistry (eds J.
Brooks and D. Welte), Vol. 1, 247-298, Academic Press, New
York.
KAUFFMAN, R., AHMED, A., and ELSINGER, R.J. 1990.
Gas chromatography as a development and production tool for
fingerprints in oils from individual reservoirs: Application in the
Gulf of Mexico. In: GC-SSEPM Foundation Ninth Annual
Research Conference Proceedings, October 1, 1990, 263-282.
LAFARGUE, E. and BURWOOD, R. 1997. Improved source
rock characterisation utilizing Rock-Eval 6 derived Oxygen
Indices. In: 18th Int. Meeting on Org. Geoch. Sept. 22-26, 1997,
Maastricht, pp. 727-728, Book of abstracts.
LARTER, S.R. and DOUGLAS, A.G. 1982. Pyrolysis methods
in organic geochemistry: An overview. J. Anal. Appl. Pyrol., 4,
1-19.
PETERS, K.E., 1986. Guidelines for evaluating petroleum
source rocks using programmed pyrolysis. AAPG Bull., 70,
329.
PETERS, K.E. and SIMONEIT, B.R.T., 1982. Rock-Eval
pyrolysis of Quaternay sediments from Leg 64, sites 479 and
480, Gulf of California. Initial Report of the Deep Sea Drilling
Project, 64, 925-931.
SCOTT, A.R., KAISER, W.R. and AYERS Jr, W.B., 1994.
Thermal maturity of Fruitland coal and composition of Fruitland
Formation and Pictured Cliffs sandstone. In: Coal Bed Methane
in the Upper Cretaceous Fruitland Formation, San Juan Basin,
New Mexico and Colorado, New Mexico and Colorado, Bull.,
146, 165-185.
TRABELSI, K., ESPITALIE, J. and HUC, A.Y. 1994.
Characterisation of extra heavy oils and tar deposits by modified
pyrolysis methods. In: European symposium on Heavy Oil
Technologies in a Wider Europe, Proceedings, June 7&8, 1994,
30-40.
van BUCHEM, F.S.P., EBERLI, G.P., WHALEN M.T.,
MOUNTJOY, E.W. and HOMEWOOD, P., 1996. The basinal
geochemical signature and platform margin geometries in the
Upper Devonian mixed carbonate-siliciclastic system of western
Canada. Bull. Soc. Geol. France, 167, 685-699.

8 / 23


FIGURES CAPTIONS


Figure 1: General diagram showing the different fractions of the total organic matter of rocks
analyzed, the corresponding parameters and their recordings.
Figure 2: Schematic diagram indicating the location of the thermocouple for temperature regulation
in the pyrolysis oven.
Figure 3: Illustration of Rock-Eval 6 standard recordings for hydrocarbons, CO and CO
2
during the
pyrolysis and oxidation phases.
Figure 4: Principle of determination of mineral carbon (MINC; %) using CO
2
pyrolysis and oxidation
curves.
Figure 5: Rock-Eval 6 response of different types of carbonate minerals illustrating their progressive
decomposition with increasing temperature.
Figure 6: Comparison of mineral carbon determination using Rock-Eval 6 and acid attack.
Figure 7: Principle of determination of the total organic carbon (TOC; %) using FID, CO
2
pyrolysis
and oxidation curves to calculate the amounts of Pyrolyzed Carbon (PC) and Residual
Carbon (RC).
Figure 8: Comparison of organic carbon determination using Rock-Eval 6 and conventional carbon
analysis method.
Figure 9: Examples of oxidation curves for a series of coal samples at increasing maturity. The
resulting TOC calculation shows the differences between Rock-Eval 6 and Rock-Eval 2
measurements.
Figure 10: Principle of determination of the Oxygen Indices using CO
2
and CO pyrolysis curves.
Figure 11: Correlation of Rock-Eval 6 Oxygen Indices across different wells of Lower Congo Basin
illustrating the transition from basin fill to sheet drape assemblages.
Figure 12: CO
2
and CO pyrolysis curves illustrating the differences of the composition of the organic
matter in the basin fill and sheet drape organo-facies.
Figure 13: Illustration of the effect of high final pyrolysis temperature with Rock-Eval 6, on the
calculation of the residual potential S2 and on the measurement of Tmax.
Figure 14: Correlation between Tmax and Ro for Rock-Eval 6 and Rock-Eval 2 on a series of coal
samples.
Figure 15: Examples of application of Rock-Eval 6 to the study of reservoir rocks.
Figure 16: Examples of application of Rock-Eval 6 to the study of contaminated soils.

9 / 23


Figure 1: General diagram showing the different fractions of the total organic matter of rocks analyzed,
the corresponding parameters and their recordings.

10 / 23



Figure 2: Schematic diagram indicating the location of the thermocouple for temperature regulation
in the pyrolysis oven.

11 / 23




Figure 3: Illustration of Rock-Eval 6 standard recordings for hydrocarbons, CO and CO
2
during
the pyrolysis and oxidation phases.

12 / 23



Figure 4: Principle of determination of mineral carbon (MINC; %) using CO
2
pyrolysis
and oxidation curves.

13 / 23



Figure 5: Rock-Eval 6 response of different types of carbonate minerals illustrating their progressive
decomposition with increasing temperature.

14 / 23




Figure 6: Comparison of mineral carbon determination using Rock-Eval 6 and acid attack.

15 / 23



Figure 7: Principle of determination of the total organic carbon (TOC; %) using FID, CO
2
pyrolysis and
oxidation curves to calculate the amounts of Pyrolyzed Carbon (PC) and Residual Carbon (RC).

16 / 23




Figure 8: Comparison of organic carbon determination using Rock-Eval 6 and
conventional carbon analysis method.

17 / 23







Figure 9: Examples of oxidation curves for a series of coal samples at increasing maturity. The resulting
TOC calculation shows the differences between Rock-Eval 6 and Rock-Eval 2 measurements.


18 / 23



Figure 10: Principle of determination of the Oxygen Indices using CO
2
and CO pyrolysis curves.

19 / 23



Figure 11: Correlation of Rock-Eval 6 Oxygen Indices across different wells of Lower Congo Basin
illustrating the transition from basin fill to sheet drape assemblages.

20 / 23









Figure 12: CO
2
and CO pyrolysis curves illustrating the differences of the composition of the organic
matter in the basin fill and sheet drape organo-facies.


21 / 23



Figure 13: Illustration of the effect of high final pyrolysis temperature with Rock-Eval 6, on the calculation
of the residual potential S2 and on the measurement of Tmax.

22 / 23




Figure 14: Correlation between Tmax and Ro for Rock-Eval 6 and Rock-Eval 2
on a series of coal samples.

23 / 23










Figure 15: Examples of application of Rock-Eval 6 to the study of reservoir rocks.

24 / 23






Figure 16: Examples of application of Rock-Eval 6 to the study of contaminated soils.