The Principles of Motion Economy

The Principles of Motion Economy
The purpose of motion economy is to maximize the work efficiency by utilizing

the following three main categories.
• Use of Human Body

• Arrangement of the Workspace
• Design of Tools and Equipments
USE OF HUMAN BODY
The two hands should begin and end their motions at the
same time:
The natural tendency of most people is to use their preferred hand (right hand
for right-handed people and left hand for left-handed people) to accomplish most
of the work. The other hand is relegated to a minor role, such as holding the
object, while the preferred hand works on it. This first principle states that both
hands should be used as equally as possible. This reason is that both hands
reinforce the effectiveness of work and helps in minimizing the time for a
particular task.
To implement, it is sometimes necessary to design the method so that the work

is evenly divided between the right-hand side and the left-hand side of the
workplace. In this case, the division of work should be organized according to the
following principle.
The work should be designed to emphasize the worker’s

preferred hand:
The preferred hand is faster, stronger, and more practical. If the work to be done
cannot be allocated evenly between the two hands, then the method should take
advantage of the worker’s best hand.
For example, work units should enter the workplace on the side of the worker’s
preferred hand and exit the workplace on the opposite side. The reason is that
1
greater hand-eye coordination is required to initially acquire the work unit, so the
worker should use the preferred hand for this element. Releasing the work unit
at the end of the cycle requires less coordination.
The worker’s two hands should never be idle at the same

time:
The work method should be designed to avoid periods when neither hand is
working. It may not be possible to completely balance the workload between the
right and left hands, but it should be possible to avoid having both hands idle at
the same time.
The exception to this principle is during rest breaks. The work cycle of a worker-
machine system may also be an exception, if the worker is responsible for
monitoring the machine during its automatic cycle, and monitoring involves
using the worker’s cognitive senses rather than the hands. If machine monitoring
is not required, then internal work elements should be assigned to the worker
during the automatic cycle.
The motions of the hands and arms should be symmetrical

and simultaneous:
This will minimize the amount of hand-eye coordination required by the worker.
And since both hands are doing the same movements at the same time, less
concentration will be required than if the two hands had to perform different and
independent motions.
Method should consist of smooth continuous curved motions

rather than straight motions with sudden changes in
direction:
It takes less time to move through a sequence of smooth continuous curved
paths than through a sequence of straight paths that are opposite in direction,
even though the actual total distance of the curved paths may be longer (since
the shortest distance between two points is a straight line).
The reason behind this principle is that the straight-line path sequence includes
start and stop actions (accelerations and decelerations) that consume the
2
worker’s time and energy. Motions consisting of smooth continuous curves
minimize the lost time in starts and stops.
Use momentum to facilitate task:

When carpenters strike a nail with a hammer, they are using momentum, which
can be defined as mass times velocity. Imagine trying to apply a static force to
press the nail into the wood.
Not all work situations provide an opportunity to use momentum as a carpenter

uses a hammer, but if the opportunity is present, we can use it. The previous
principle dealing with smooth continuous curved motions illustrates a beneficial
use of momentum to make a task easier.
Take advantage of gravity & don’t oppose it:

Less time and energy are required to move a heavy object from a higher
elevation to a lower elevation than to move the object upward. The principle is
usually implemented by proper layout and arrangement of the workplace, and so
it is often associated with the workplace arrangement principles of motion
economy.
Method should achieve a natural cadence of the motions

involved:
Rhythm refers to motions that have a regular recurrence and flow from one to
the next. Basically, the worker learns the rhythm and performs the motions
without thinking, much like the natural and instinctive motion pattern that occurs
in walking.
Use lowest classification of hand and arm motion (five

classifications):
With each lower classification, the worker can perform the hand and arm motion
more quickly and with less effort. Therefore, the work method should be
composed of motions at the lowest classification level possible.
3
This can often be accomplished by locating parts and tools as close together as
possible in the workplace.
Classifications are as follows:
1- Finger motion only.

2- Finger and wrist motion
3- Finger, wrist and forearm motion
4- Finger, wrist, forearm and upper arm motion.
5- Finger, wrist, forearm, upper arm and shoulder motion.
Minimize eye focus and travel:

In work situations where hand-eye coordination is required, the eyes are used to
direct the actions of the hands. Eye focus occurs when the eye must adjust to a
change in viewing distance.
For example, from 25 in. to 10 in. with little or no change in line of sight.
Eye travel occurs when the eye must adjust to a line-of-sight change
For example, from one location in the workplace to another, but the distances
from the eyes are the same. Since eye focus and eye travel each take time, it is
desirable to minimize the need for the worker to make these adjustments as
much as possible. This can be accomplished by minimizing the distances
between objects (e.g. parts and tools) that are used in the workplace.
The method should be designed to utilize the worker’s feet

and legs when appropriate:
The legs are stronger than the arms, although the feet are not as practical as the
hands. The work method can sometimes be designed to take advantage of the
greater strength of the legs, for example, in lifting tasks.
4
ARRANGEMENT OF THE WORKPLACE
Locate tools and materials in fixed positions within the work

area:
As the saying goes, “a place for everything, and everything in its place.” The
worker eventually learns the fixed locations, allowing him to reach for the object
without wasting time looking and searching.
Locate tools and materials close to where they are used:

This helps to minimize the distances the worker must move (travel empty and
travel loaded) in the workplace. In addition, any equipment controls should also
be located in close proximity. This guideline usually refers to a normal and
maximum working area. It is generally desirable to keep the parts and tools used
in the work method within the normal working area, as defined for each hand
and both hands working together.
If the method requires the worker to move beyond the maximum working area,
then the worker must move more than just the arms and hands. This expends
additional energy, takes more time, and ultimately contributes to greater worker
fatigue.
Locate tools and materials to be consistent with sequence of

work elements:
Items should be arranged in a logical pattern that matches the sequence of work
elements. Those items that are used first in the cycle should be on one side of
the work area, the items used next should be next to the first, and so on.
The alternative to this sequential arrangement is to locate items randomly in the

work area. This increases the amount of searching required and detracts from
the rhythm of the work cycle.
5
Use gravity drop chutes (channels, tubes) for completed
work units where appropriate:
The drop chutes should lead to a container adjacent to the worktable. The
entrance to the gravity chute should be located near the normal work area,
permitting the worker to dispose of the finished work unit quickly and
conveniently. They are most appropriate for lightweight work units that are not
fragile.
Provide adequate illumination:

The issue of illumination is normally associated with ergonomics. However,
illumination has long been known to be an important factor in work design.
Illumination is especially important in visual inspection tasks.
A proper chair should be provided for the worker:

This usually means an adjustable chair that can be fitted to the size of the
worker. The adjustments usually include seat height and back height. Both the
seat and back are padded.
Many adjustable chairs also provide a means of increasing and decreasing the
amount of back support. The chair height should be in proper relationship with
the work height.
Design of Tools and Equipments:
Work-holding devices should be designed for the task:

A mechanical workholder with a fast-acting clamp permits the work unit to be
loaded quickly and frees both hands to work on the task productively.
Typically, the workholder must be custom-designed for the work part processed
in the task.
6
Hands should be relieved of work elements that can be
performed by the feet using foot pedals:
Foot pedal controls can be provided instead of hand controls to operate certain
types of equipment. Sewing machines are examples in which foot pedals are
used as integral components in the operation of the equipment.
As our examples suggest, training is often required for the operator to become
proficient in the use of the foot pedals.
Combine multiple functions into one tool where possible:

Many of the common hand tools implements this principle, such as head of a
claw hammer is designed for both striking and pulling nails. Nearly all pencils are
designed for both writing and erasing. Less time is usually required to reposition
such a double-function tool than to put one tool down and pick another one up.
Perform multiple operations simultaneously rather than

sequentially:
A work cycle is usually conceptualized as a sequence of work elements or steps.
The steps are performed one after the other by the worker and machine. In some
cases, the work method can be designed so that the steps are accomplished at
the same time rather than sequentially. Special tooling and processes can often
be designed to simultaneously accomplish the multiple operations.
Where feasible, perform operation on multiple parts

simultaneously:
This usually applies to cases involving the use of a powered tool such as a
machine tool. A good example is the drilling of holes in a printed circuit board
(PCB). The PCBs are stacked three or four thick, and a numerically controlled drill
press drills each hole through the entire stack in one feed motion.
7
Design equipment controls for operator convenience and
error avoidance:
Equipment controls include dials, cranks, levers, switches, push buttons, and
other devices that regulate the operation of the equipment. All of the controls
needed by the operator should be located within easy reach, so as to minimize
the body motions required to access and activate them.
Hand tools and portable power tools should be designed for

operator comfort & convenience:
For example, the tools should have handles or grips that are slightly
compressible so that they can be held and used comfortably for the duration of
the shift.
The location of the handle or grip relative to the working end of the tool should
be designed for maximum operator safety, convenience, and effectiveness of the
tool. If possible, the tool should accommodate both right-handed and left handed
workers.
Mechanize or automate manual operations if economically

and technically feasible:
Mechanized or automated equipment and tooling that are designed for the
specific operation will almost always outperform a worker in terms of speed,
repeatability, and accuracy. This results in higher production rates and better
quality products.
The economic feasibility depends on the quantities to be produced. In general,

higher quantities are more likely to justify the investment in mechanization and
automation.

The Principles of Motion Economy

Uploaded by

Copyright:

Available Formats

The Principles of Motion Economy

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

The Principles of Motion Economy

Uploaded by

Copyright:

Available Formats

The Principles of Motion Economy

The purpose of motion economy is to maximize the work efficiency by utilizing

• Use of Human Body

USE OF HUMAN BODY

To implement, it is sometimes necessary to design the method so that the work

The work should be designed to emphasize the worker’s

The worker’s two hands should never be idle at the same

The motions of the hands and arms should be symmetrical

Method should consist of smooth continuous curved motions

Use momentum to facilitate task:

Not all work situations provide an opportunity to use momentum as a carpenter

Take advantage of gravity & don’t oppose it:

Method should achieve a natural cadence of the motions

Use lowest classification of hand and arm motion (five

Classifications are as follows:

1- Finger motion only.

Minimize eye focus and travel:

The method should be designed to utilize the worker’s feet

Locate tools and materials in fixed positions within the work

Locate tools and materials close to where they are used:

Locate tools and materials to be consistent with sequence of

The alternative to this sequential arrangement is to locate items randomly in the

Provide adequate illumination:

A proper chair should be provided for the worker:

Design of Tools and Equipments:

Work-holding devices should be designed for the task:

Combine multiple functions into one tool where possible:

Perform multiple operations simultaneously rather than

Where feasible, perform operation on multiple parts

Hand tools and portable power tools should be designed for

Mechanize or automate manual operations if economically

The economic feasibility depends on the quantities to be produced. In general,

You might also like