HSF Release Notes v7.75

Copyright 2004-2008 by Conexant Systems.
All rights reserved

8/11/2008
Conexant SoftModem Driver
Release Notes
Conexant Confidential 2 08/11/08

Table of Contents
TABLE OF CONTENTS.................................................................................................................. 3
INTRODUCTION............................................................................................................................. 6
COUNTRY/REGION SUPPORT ..................................................................................................... 7
V.92 Feature Support ..................................................................................................... 8
SOFTMODEM RELEASE NOTES.................................................................................................. 9
Version 7.75.00............................................................................................................... 9
Version 7.74.00............................................................................................................... 9
Version 7.73.00............................................................................................................... 9
Version 7.72.00............................................................................................................... 9
Version 7.71.00............................................................................................................. 10
Version 7.70.00............................................................................................................. 10
Version 7.69.00............................................................................................................. 10
Version 7.68.00............................................................................................................. 11
Version 7.67.00............................................................................................................. 11
Version 7.66.00............................................................................................................. 11
Version 7.65.00............................................................................................................. 11
Version 7.64.00............................................................................................................. 11
Version 7.63.00............................................................................................................. 11
Version 7.62.00............................................................................................................. 12
Version 7.61.00............................................................................................................. 12
Version 7.60.00............................................................................................................. 13
Version 7.59.00............................................................................................................. 13
Version 7.58.00............................................................................................................. 13
Version 7.57.00............................................................................................................. 14
Version 7.56.00............................................................................................................. 15
Version 7.55.00............................................................................................................. 15
Version 7.54.00............................................................................................................. 15
Version 7.53.00............................................................................................................. 16
Version 7.52.00............................................................................................................. 16
Version 7.51.00............................................................................................................. 17
Version 7.50.00............................................................................................................. 17
Version 7.49.00............................................................................................................. 17
Version 7.48.00............................................................................................................. 17
Version 7.47.00............................................................................................................. 18
Version 7.46.00............................................................................................................. 18
Version 7.45.00............................................................................................................. 18
Version 7.44.00............................................................................................................. 18
Version 7.43.00............................................................................................................. 19
Version 7.42.00............................................................................................................. 19
Version 7.41.00............................................................................................................. 19
Version 7.40.00............................................................................................................. 20
Version 7.39.00............................................................................................................. 21
Version 7.38.00............................................................................................................. 21
Version 7.37.00............................................................................................................. 21
Version 7.36.00............................................................................................................. 21

Version 7.35.00............................................................................................................. 21
Version 7.34.00............................................................................................................. 22
Version 7.33.00............................................................................................................. 22
Version 7.32.00............................................................................................................. 22
Version 7.31.00............................................................................................................. 23
Version 7.30.00............................................................................................................. 23
Version 7.29.00............................................................................................................. 23
Version 7.28.00............................................................................................................. 23
Version 7.27.00............................................................................................................. 23
Version 7.26.00............................................................................................................. 24
Version 7.25.00............................................................................................................. 24
Version 7.24.00............................................................................................................. 24
Version 7.23.00............................................................................................................. 25
Version 7.22.00............................................................................................................. 25
Version 7.21.00............................................................................................................. 25
Version 7.20.00............................................................................................................. 26
Version 7.19.00............................................................................................................. 26
HOMOLOGATION/COUNTRY FILE CHANGES.......................................................................... 28
Master CTY file Updated to v1.28 starting from Modem Driver V7.73.00 ............... 28
Master CTY file Updated to v1.20 starting in v7.48.00 ............................................. 29
Master CTY file Updated to v1.19bis starting in v7.45.00 ........................................ 29
Master CTY file Updated to v1.17 for dedicated internal process. ......................... 30
XAUDIO (SOFT CALL PROGRESS FOR WINDOWS VISTA) .................................................... 33
Version 1.0.15.0............................................................................................................ 33
Version 1.0.8.0 1.0.14.0 ACF modem fixes ONLY.................................................. 33
Version 1.0.7.0.............................................................................................................. 33
Version 1.0.5.0 1.0.6.0 ACF modem fixes ONLY.................................................... 33
Version 1.0.4.0.............................................................................................................. 33
Version 1.0.3.0.............................................................................................................. 33
Version 1.0.1.0 and Version 1.0.2.0............................................................................ 33


Introduction
Please refer to the product documentation for full details of features supported in the HSF driver.

Country/Region Support
Unless modified in a particular release package the following list of countries/regions are
supported in the current release:

AFGHANISTAN
ALBANIA
ALGERIA
AMERICAN SAMOA
ANDORRA
ANGOLA
ANGUILLA
ANTIGUA AND BARBUDA
ARGENTINA
ARMENIA
ARUBA
ASCENSION ISLAND
AUSTRALIA
AUSTRIA
AZERBAIJAN
BAHAMAS
BAHRAIN
BANGLADESH
BARBADOS
BELARUS
BELGIUM
BELIZE
BENIN
BERMUDA
BHUTAN
BOLIVIA
BOSNIA AND HERZEGOVINA
BOTSWANA
BRAZIL
BRITISH VIRGIN ISLANDS
BRUNEI
BULGARIA
BURKINA FASO
BURUNDI
CAMBODIA
CAMEROON
CANADA
CAPE VERDE
CAYMAN ISLANDS
CENTRAL AFRICAN REPUBLIC
CHAD
CHILE
CHINA
CHRISTMAS ISLAND
COCOS KEELING ISLANDS
COLOMBIA
COMOROS
CONGO
COOK ISLANDS
COSTA RICA
COTE D'IVOIRE
CROATIA
CUBA
CYPRUS
CZECH REPUBLIC
DEMOCRATIC PEOPLE'S REPUBLIC OF KOREA
DENMARK
DIEGO GARCIA
DJIBOUTI
DOMINICA
DOMINICAN REPUBLIC
EAST TIMOR
ECUADOR
EGYPT
EL SALVADOR
EQUATORIAL GUINEA
ERITREA
ESTONIA
ETHIOPIA
FALKLAND ISLANDS
FAROE ISLANDS
FIJI
FINLAND
FRANCE
FRENCH ANTILLES
FRENCH GUIANA
FRENCH POLYNESIA
GABON
GAMBIA
GEORGIA
GERMANY
GERMANY
GHANA
GIBRALTAR
GREECE
GREENLAND
GRENADA
GUADELOUPE
GUAM
GUANTANAMO BAY
GUATEMALA
GUINEA
GUINEA-BISSAU
GUYANA
HAITI
HONDURAS
HONG KONG
HUNGARY
ICELAND
INDIA
INDONESIA
INMARSAT ATLANTIC EAST
INMARSAT ATLANTIC EAST
INMARSAT ATLANTIC WEST
INMARSAT INDIAN
INMARSAT PACIFIC
INTERNATIONAL FREEPHONE SERVICE
IRAN
IRAQ
IRELAND
ISRAEL
ITALY
JAMAICA
JAPAN
JORDAN
KAZAKHSTAN
KENYA
KIRIBATI
KOREA
KUWAIT
KYRGYZSTAN
LAOS
LATVIA
LEBANON
LESOTHO
LIBERIA
LIBYA
LIECHTENSTEIN
LITHUANIA
LUXEMBOURG
MACAO
MACEDONIA
MADAGASCAR
MALAWI
MALAYSIA
MALDIVES

MALI
MALTA
MARSHALL ISLANDS
MARTINIQUE
MAURITANIA
MAURITIUS
MAYOTTE
MEXICO
MICRONESIA, FEDERATED STATES OF
MOLDOVA
MONACO
MONGOLIA
MONTSERRAT
MOROCCO
MOZAMBIQUE
MYANMAR
NAMIBIA
NAURU
NEPAL
NETHERLANDS ANTILLES
NETHERLANDS
NEW CALEDONIA
NEW ZEALAND
NICARAGUA
NIGER
NIGERIA
NIUE
NORFOLK ISLAND
NORWAY
OMAN
PAKISTAN
PALAU
PANAMA
PAPUA NEW GUINEA
PARAGUAY
PERU
PHILIPPINES
POLAND
PORTUGAL
PUERTO RICO
QATAR
REUNION ISLAND
ROMANIA
ROTA ISLAND
RUSSIA
RWANDA
SAINT HELENA AND ASCENSION
SAINT KITTS AND NEVIS
SAINT LUCIA
SAINT VINCENT AND THE GRENADINES
SAIPAN ISLAND
SAN MARINO
SAO TOME AND PRINCIPE
SAUDI ARABIA
SENEGAL
SEYCHELLES
SIERRA LEONE
SINGAPORE
SLOVAKIA
SLOVENIA
SOLOMON ISLANDS
SOMALIA
SOUTH AFRICA
SPAIN
SRI LANKA
ST PIERRE ET MIQUELON
SUDAN
SURINAME
SWAZILAND
SWEDEN
SWITZERLAND
SYRIA
TAIWAN
TAJIKISTAN
TANZANIA
THAILAND
TINIAN ISLAND
TOGO
TOKELAU
TONGA
TRINIDAD AND TOBAGO
TUNISIA
TURKEY
TURKMENISTAN
TURKS AND CAICOS ISLANDS
TUVALU
UGANDA
UK
UKRAINE
UNITED ARAB EMIRATES
URUGUAY
US VIRGIN ISLAND
USA
UZBEKISTAN
VANUATU
VATICAN CITY
VENEZUELA
VIETNAM
WALLIS AND FUTUNA
WESTERN SAMOA
YEMEN
YUGOSLAVIA
ZAIRE
ZAMBIA
ZIMBABWE
V.92 Feature Support
All V.92 features are on by default in this release. If you want a driver that only supports V.90 and
V.34 modulations, please release it specifically, for 7.24.00 and above, a customized release is
required.

SoftModem Release Notes
Version 7.75.00
Problems Fixed/New Features Added
Operating
System
Hardware
Platform
On certain system there may be some sluggishness and failure
during handshake
Vista64 All
A BSOD may occur when rolling back using device manager to
an old driver version after a successful V.92 connection using a
new version
WinXP All
Version 7.74.00
Operating
System
Hardware
Platform
OCA crash: ATTEMPTED_SWITCH_FROM_DPC (B8) in
HSX_CNXT.sys
Vista All
BSOD with SYSTEM_SERVICE_EXCEPTION (3b) if memory
allocation fails when copying the contents of the CTY file into
the registry (copy usually happens during the installation)
All All
Potential BSOD with PAGE_FAULT_IN_NONPAGED_AREA
(50) when copying the contents of the CTY file into the registry
or creating the response to the +GCI=? command (both usually
happens during the installation)
All All
Version 7.73.00
Operating
System
Hardware
Platform
BSOD when modem DTM test suits disables HDA bus driver
during the WLK 1.2 WHQL test
Vista HDA modem
Version 7.72.00
Operating
System
Hardware
Platform
Erroneous echo loss value is by the #UG and #UD commands. All All
Intermittent failures when connecting to servers from different
ISP. Issue is caused by the server not following the required
standards. Connectivity problem is solved by enabling V.8bis at
modem client side.
All All
INF: Stored QC profile is cleared during the installation to
prevent possible incompatibility issues of QC profile structure
and size between old and new modem drivers
All All
INF: Close DLD application if it is running when uninstalling
modem driver
All All
On the same line (line condition does not change) many
subsequent QC calls takes the same amount of time to connect
as a non-QC call.
All All
Intermittent fallback to V.34 modulation when the line has
alternating RBS
All All
Downstream (Rx) rates using V.90 modulation may be limited
by sub-optimal EC convergence on difficult line loops
All All

Intermittent obsolete phase 2 error-recovery during QC
connection attempt.
All All
Possible fallback to V.34 modulation or low V.90 rate on long or
loaded line loops
All All
MOH session disconnects if user rejects incoming call when
connected to NACK server
All All
Version 7.71.00
Operating
System
Hardware
Platform
Driver Verifier failure (blue screen) when system fails to allocate
memory for DMA buffer
All All
Driver Verifier failure (blue screen) when driver is releasing
mutex object that was never allocated.
All All
Added support for the 2
nd
revision of PCIe modem All PCIe modem
Modem doesnt detect remote phone disconnection (and stays
off-hook) if CO indicates the disconnection with busy or fast
busy tone and that tone is detected as call waiting tone by
modem
All All
Version 7.70.00
Operating
System
Hardware
Platform
Failure to connect against Cisco CSMv6 and Lucent V.92
servers when Quick Connect is enabled
Windows 2000 All
Failure to connect using V.90 modulation against Lucent server
on loaded loops
Windows 2000 All
Failure to connect against Lucent server when PCM upstream is
enabled
Windows 2000 All
Modem fails to connect using V.90 modulation over wireless
DECT Phone Line Extender to a specific server in the UK
All All
Blue screen occurred when running driver verifier (bug check
C4) caused by running intermittently at wrong IRQL when
processing the data from DTE.
All All
Version 7.69.00
Operating
System
Hardware
Platform
Modem fails to connect using V.34 modulation over wireless
DECT Phone Line Extender to a specific server in Italy. V.90
connection is successful.
All All
Fixed a crash in Windows Vista modem driver that appeared
from Microsoft OCA bug report.
Windows Vista All
Failure to establish PPP connection with DUN and customized
script in Windows 2000 against a specific server.
Windows 2000 All
Noise is heard at remote side when calling from Fax Talk
application because the modem falsely reports speakerphone
capability to the application.
All All

Version 7.68.00
Operating
System
Hardware
Platform
AT|LC command to measure the loop current is functional ALL HAL
Version 7.67.00
Operating
System
Hardware
Platform
Blue screen occurs when performing Wake On Ring or going to
hibernation
Windows XP All
Reconnection fails from Modem on Hold state if Call Waiting
arrives without CID
All All
Version 7.66.00
Operating
System
Hardware
Platform
On some systems, when call progress starts after a stream is
already playing, there will be many interruptions that make it
appear like it is stuttering. Also, when running from battery, call
progress is always distorted, with or without playing a stream.
Windows XP All
Off-hook squeaks when using a buzzer All HAL
Version 7.65.00
Operating
System
Hardware
Platform
WOR is unreliable on Windows Vista and fails randomly (system
dependant)
Windows Vista All
Intermittent system lock up after NO DIALTONE happening after
500 to 3000 calls on Rainier platforms.
All Rainier
Version 7.64.00
Operating
System
Hardware
Platform
Fix pulse break failure in Australia with HAL designs. All HAL
Off hook power setting algorithm changed to correct an earlier
fix for handset detection
All
SmartHSFi
SmartMC3z
FixpotentialcauseforbluescreenonWindowsVistaduring
shutdown.
Windows Vista All
Version 7.63.00
Operating
System
Hardware
Platform
Fixed Pulse dialing on modems using SiLabs codec. All All
Issue with AT command AT&Zn where a saved phone number
in profile could not be modified or deleted. This issue is resolved
All All
Enhancements to AT command AT#UD. This command reports
port settings and last call time.
All All
Using the ATDL command the last number dialed is not redialed
after the modem port is closed and re-opened.
All All

IfPCMupstreamisdisabledintheINForCTYfile,AT+PIG=?
commandnowreturns(1).Previouslyitreturned(0,1)indicating
thatPCMUpstreamwasanoption.InAddition,AT+PIG=1
commandnowreturnsanOKresponse.Previouslyitreturned
[error].
All All
Version 7.62.00
Operating
System
Hardware
Platform
The AT&F0 command is now an alias to the existing AT&F
command [reset the modem settings to factory default]
All All
Modem handshake volume for pulse dialing was slightly higher
than tone dialing. Adjusted the volume so that Pulse and Tone
dialing are equal.
XP All
Version 7.61.00
Operating
System
Hardware
Platform
Add support for Conexant PCI Express modem (Rainier) All SmartHSF4e
Decrease Digital Line Detection (DLD) time from 240 ms to 120
ms to increase product reliability
All
Modem with
SmartDAA
Increase TBR-21 line seizure margin for SmartDAA3
(CX20493). This change provides a bigger margin to pass
regulatory tests in Europe.
All
Modem with
SmartDAA3
(CX20493)
Change the names of silent Universal Installer/Uninstaller (UIU)
and Universal CoInstaller (UCI) files for modem to avoid conflict
with the corresponding files from Conexant Audio drivers.
Files with the same name and contents may cause WHQL
system failures if both modem and audio drivers are Conexant
based.

New naming convention for silent UIU for modem:
UIU32m.exe for 32-bit OS
UIU64m.exe for 64-bit OS

New naming convention for UCI for modem:
UCI32Mnn.dll for 32-bit OS
UCI64Mnn.dll for 64-bit OS

Note: M stands for modem
nn stands for the last 2 digits of the UCI version.
All All
Fix an intermittent system crash (BSOD) when system goes to
Stand-by mode while the modem connection is active. The
problem is system specific and caused by a race condition
between OS services and modem driver.
Windows Vista All
System locks up when the system goes into Stand-by mode
while the modem connection is active and "Allow Hybrid Sleep"
settings in Power Management control panel is set to "Off".
The default setting of "Allow Hybrid Sleep" in the OS is "On" and
with this setting the problem doesn't show up.
This issue was resolved.
Windows Vista All
Wake On Ring (WOR) is not functional when the system goes
into Stand-by mode while modem connection is active.
This issue was resolved.
Windows Vista PCI modem

Fixed an intermittent failure to establish a successful connection
on very difficult lines (line characteristics close to the 2A6
standard). This issue was caused by failed error correction
negotiation.
All All
Improvement for V.90 connection rates on a very long line (~26
Kft).
All All
Fixed low connectivity rates or failure to connect the modem
with Discrete DAA and SoftRing detection. Issue was observed
during an automated test that does not close the ports between
each session. The problem is not observed in a real world
scenario (Dial-Up Networking, etc.) where the modem port is
reopened on every dial attempt. Problem was introduced in
7.60.00
All
Modem with
Discrete DAA
and SoftRing
circuitry
INF Changes:
Failure to load INF file under DTM RC2. To attain WHQL logo
for Windows 2000 and Windows XP it is required to use
Windows Vista DTM.
This is a Windows Vista problem introduced in DTM RC2 and
fixed in DTM RTM.
The workaround is to use the following:
[SourceDisksNames]
1 = %WINDiskName%,,,
instead of
[SourceDisksNames]
1 = %WINDiskName%,Disk1
Windows 2000
Windows XP
All

Version 7.60.00
Operating
System
Hardware
Platform
Intermittent failure to detect ring after successful V.90 or V.92
connection with modem board requiring software ring detection.
WDM SL2801

Version 7.59.00
Operating
System
Hardware
Platform
Intermittent false detection of Call Waiting tone while modem is
connected. This is a very rare condition and it could result in the
session to be disconnected.
WDM All
Bug check randomly happening when system goes to the
suspend state during the "Sleep Stress with I/O" test from DTM
RC2.
Windows Vista All

Version 7.58.00
Operating
System
Hardware
Platform
Bug check 0x3b while running devctl.exe on Windows Vista,
caused by
Failure to allocate DMA during devctl.exe test which injects fault
conditions when accessing the DMA later. The fix was to:
1) Return initialization result to upper layer.
2) Validate DMA buffer pointer before access.
WDM All

Bug check 0x9F randomly happening when resume from
standby or Hibernate starting from Windows Vista Beta 2 (build
5384).
When modem goes to D3, a series of events will power down
the codec and enable wake on ring. Sometimes, the bus driver
will already be in lower power state and reject any requests
coming in. This can also cause further failures when system
resumes.
The fix was to change the order of events and check for certain
conditions before making power management calls to avoid
scenarios where there is no response form the bus driver.
WDM All
Modem connection is stuck when CW CID arrives and country is
set to China
The problem was fixed by:
1) Allowing DTMF CID only for CID type 1
2) Add a new state handler for a state that previously was not
handled correctly
WDM All
Random CWCID failure during MOH sessions using NetWaiting
Fixed by changing the method of detecting and identifying CID
type 2.
WDM All
Failures to detect CID type 1 on some test cases in TIA/EIA
777A
Changed the logic in some of the routines handling CID type 1
detection.
WDM All
Add support for call hopping on Windows Vista WDM Windows Vista
INF changes:
1) Force BUFFERS=OFF for modems that have no hardware
buffers (ignore INF setting)
2) Default volume setting should be L3 for modems with buzzer
CP
3) Synchronize the settings for KMixer initial delays for 32 and
64-bit systems
4) Add entries for XAudio files to make sure the CoInstaller will
remove them during uninstall.
5) Ignore DaaType setting from INF for modems that supports
just Discrete DAA
6) Add new INF files for all relevant OS/type/etc. combination so
that call progress will route though buzzer when sound driver is
disabled on a system with SmartSP board with buzzer.
7) For HDAUDIO modem, UIPATH in default INFs should use
HDAUDIO instead of PCI
8) Add HDAUDIO prefix to ProductName definition for
HDAUDIO modem in default INFs.
9) Remove obsolete commented out lines referring to csacpl.cpl
10) Failure to load INF file under DTM RC2
This is a Microsoft problem introduced in DTM RC2.
The workaround is to use
[SourceDisksNames]
1 = %WINDiskName%,,,
instead of
[SourceDisksNames]
1 = %WINDiskName%,Disk1
All All

Version 7.57.00
Operating
System
Hardware
Platform

Removed the code that releases and re-allocates the DMA
which was added as a workaround for an issue with bus driver
version 1013 and is no longer needed.
This was causing a BSOD during power management test of
DTM.
WDM
All platforms
with SoftRing
Detection
INF changes:
1) XAudio .sys and .exe file names were changed for 64-bit
Windows Vista
2) Define blanks instead of empty strings for +GOI and +GSN
values to avoid INFCHK errors
3) Add infrastructure for Lassen (INF files, PVCS folders) for all
OS
All All

Version 7.56.00
Operating
System
Hardware
Platform
System lock up when going to S3 or hibernation with HDA
modem. The modem was changed to work around a system
lock seen on a specific system. The lock was seen while
returning from, or going to, a low power system state. The
modem was found to be in a loop waiting for the bus driver. The
change in the modem is to remove an indefinite wait state in the
case where the bus driver is unavailable. This allows the system
to return or enter the desired state without locking up. This does
not ensure that the modem will work, as the bus driver must be
available for proper modem operation.
WDM
SmartMC4,
SmartAMCHD2
Version 7.55.00
Operating
System
Hardware
Platform
The modem was seen to have Random CWCID failures (4%).
The modem Caller ID detection scheme was modified to add
tolerance for the timing between the signaling and the data.
All All
WOR was reported as not working on Windows Vista for Teton
HDAudio. The problem was found to be in the configuration.
The modem was changed to accommodate different ring
detection schemes used with the HSF Teton. The new
configuration method was added which allows the INF to control
whether the hardware ring detection method or the software ring
detection method.
Windows Vista HSF
Add the ability to hide the power management tab in the modem
properties.
Windows
2000,
Windows XP,
AMD64
All
Version 7.54.00
Operating
System
Hardware
Platform
The modem was changed to correct a reference to an
uninitialized set of parameters. A change to the codec interface
made in 7.50.00 introduced the problematic reference on ATi ,
ALi, SIS and VIA. The problem did not exist in the ICH hardware
module. The problem does not exist for ver 7.49.00 and below.
In the failing condition the modem port open during installation
WDM
AC'97 modems
on ALi, VIA,
ATi

would cause a system failure.
Version 7.53.00
Problems Fixed/New Features Added Operating System Hardware Platform
The modem was changed to prevent a system failure
seen during Driver Verifier NDIS-Standby Open test.
The modem driver was attempting to access information
that had expired. This access of invalid information
causes the system to blue screen. The change adds
conditional checks on the information to ensure that
they are valid prior to access. The blue screen indicates
that the failure was probably caused by
HSF_CNXT.sys.
WDM All
The modem was changed to implement a work around
for an issue seen with SmartHSF4 (Bryce) when
attempting WOR from S4. The symptom was that the
system was no longer responsive after the RING was
detected and the system begins to return from S4. The
problem was found to be rooted in the status of the PLL
used for the clock signal. In the failure mode the PLL
was not configured to run. The work around is to ensure
that the PLL is running in the routine used to return from
the low power state. Since the SmartDAA4 does not
have more than one power mode, it was assumed that
the PLL (clock) would be running while the modem is
active. The change is to remove the assumption and to
verify the clock is running when the modem is directed
to return from the low power state.
WDM
SmartHSF4
(Bryce)
Version 7.52.00
CTY file updated to 1.21 for
1) CAS time out for China
2) Sreg for Belarus and Japan
3) TXLevel Smart TXLevel for Belarus
4) SmartRelays for Mexico
All All
Can not power up Bryce X3 LSD WDM SmartMC3s (HAL)
No CP on Windows Vista when driver is installed over
an existing driver
All All
No CWCID was displayed on NW for incoming call in
CHINA
WDM All
System locks up entering S3 while modem is connected WDM All
System hangs during hibernate resume test on Intel
dual core.
WDM
HDA in Hyper
threading and Dual
Core systems
After hot swap of Riesling PCI boards, pci configuration
space is lost.
WDM PCI
Call hopping for Lassen is disabled in the driver, need
to re-enable
WDM Lassen
Windows Vista build 5444 Blue screen during modem
installation
Windows Vista-
specifically build
5444
All

Version 7.51.00
Blue screen on AMD dual core system WDM HDAudio
Windows Vista build 5444 Blue screen during modem
installation
Windows Vista All
Call Waiting tone is not detected on a specific line when
connected at V90
WDM All
DOS test does not set CPU rate (no effect on Windows
driver)
DOS HDAudio
Version 7.50.00
Added support for new SiLabs codec IDs. All All
Cosmetic changes in DTMF generator All All
Version 7.49.00
"NO CARRIER" is printed too long after remote hang
up.
All SmartMC3z
NetWaiting does not pop up during incoming call when
connected v90
Windows 2000,
Windows XP,
AMD64
All
V.32 Tx Level Sometimes Marginally Fails (between -10
and -9.8 dBm)

Version 7.48.00
CTY file update to 1.20 All All
Change UIU naming in x64. The silent
installation/uninstallation utility changed from
Setup64.exe to HXFSetup64.exe
AMD64 All
Congestion tone is detected as dial tone in European
countries
All All
HCT enable/disable test blue screens using 64-bit Zion
speakerphone driver
Windows XP,
AMD64
SmartMC3z
Modem fails to pulse dial on AMD dual core system. A
workaround was introduced to avoid erroneous timing
reports from specific AMD X2 processors. This patch is
not required if the system is patched with software
updates from AMD and Microsoft.
Windows XP SmartAMC2
Introduction of a new file naming convention to separate
driver names between Windows Vista and XP.
All All
Pulse dialing failed for countries set to pulse with slow
edge (e.g. France)
Windows 2000,
Windows XP,
AMD64
SmartMC3s
Zion/Hal has low throughput with certain transformers
Windows 2000,
Windows XP,
AMD64
SmartMC3s

Version 7.47.00
Operating
System
Hardware
Platform
Need to update CTY file for Brazil power test All All
Call progress / speakerphone does not work on latest
Windows Vista builds
Windows Vista All
Caller ID does not work. All HAL
Version 7.46.00
Operating
System
Hardware
Platform
Quick connect always fails (successful connection but
with full training)
All All
Driver does not build with WDK(Longhorn DDK)
Windows 2000
Windows XP
AMD64
All
ECS P13G Teton CNR (AC97) can't WOR in Win98
Windows 98
Second Edition
AC-Link modem
with Intel AC-Link
controller
Version 7.45.00
Call KeFlushQueuedDpcs() provided in Sever 2003
DDK by address in runtime instead of linking with it at
build time so we can still use the same driver for
Windows 2000 and Windows XP.
Windows 2000
Windows XP
AMD64
All
Connecting to a certain server (Sony Internal Server)
using Dial Up Networking, the negotiation sequence
does not complete and we get connection failure.
All All
Problem with HCT PCI Compliance test specific to Ali
platforms.
Windows XP SmartMC3S- ALi
Version 7.44.00
The modem driver was changed to place the modem
back on hook when presented with the line conditions
associated with the power cross test. This specific
test is part of the Brazilian modem qualification tests.
Windows XP
AMD64
HSF
A fix was implemented to correct gain settings in the
codec after connecting at V.90 on certain lines. When
the modem is placed back on hook the gain settings
are reset as to allow proper ring detection. A gain
switch change was also implemented that corrected a
failure to detect caller ID. The In order to detect an
incoming ring signal and then the CID signal to
follow, the codec gains must switch from low to high
gain and then back to low. This functionality has been
fixed in this version of the HSF. This change applies
to discrete DAA products using softring. Specifically
this fix applies to lead-free HSFi for ring detection
and to Teton for ring detection and caller ID.
Windows XP
AMD64
HSF

A Work around introduced for SiS AC97 modems
going to S3. The modem now checks to see if the
audio device has prepared the bus for power down. If
the bus has not been prepared the modem makes
the proper settings before going to the low power
state. This workaround resolves a failure to wake on
ring in Windows 2000 and in prior versions of the
operating system. Windows Xp does not require this
work around.
Windows 2000
Windows 98
Second Edition
WDM drivers
HSF
Version 7.43.00
New entries are added to the INF files, some for HAL
specific and some for all products.
All All
CallHopping feature support is added to the driver
code.
All All
Version 7.42.00
Changes required for building Linux drivers. Linux All
Driver does not work with smart link modem, changes
added for HSP support.
All HSP
Timing and overrun/underrun fixes for Windows Vista
XAudio (call progress) code.
Windows Vista All
Fix for WOR issue on Ali platforms.
Windows XP
AMD64
AC-Link modem
with ALi AC-Link
controller
Intermittent V.32 connect failures caused by wrong
initialization of the PLL and timing correction. This was
discovered during internal testing with a certain line
against a certain reference modem.
All All
V.34 Tx Level cannot be increased above -10 dBm
Discovered during PTT testing for India.
All All
Changes made specifically for embedded Fax product
does not get compiled for HSF drivers but is in the
common code base.
All All
Version 7.41.00
When softring is enabled, after manually resuming from
S3 via mouse or power button, modem can not detect
ring until we go off-hook and then back on-hook.
Ring detection works fine after coming out of S3 via
WOR.
When h/w ring is enabled, ring detection works fine.
All All
Bryce specific fix, when using PLL configuration, on
certain systems DIB clock is not ON and therefore,
driver can not access LSD.
Windows XP SmartMC*
When we dial out on Via platforms, sometimes the
system will freeze & display black screen
Windows XP
AMD64
SmartMC3S
AC-Link modem

with VIA AC-Link
controller
Startup failure with certain Venice (HAL LSD) devices All SmartMC3z
Using HyperTerminal, dial out and while the Modem is
still off-hook, go to suspend mode(S3). The system
closes all applications including HyperTerminal, screen
blank out and appears ready to suspend but power is
never turned off and the hard disk remains spinning. If
the Modem is not in off-hook state, then these is no
problem.
Fixed by closing the steam in KMixer during shutdown.
Windows XP
AMD64
All
Fixed sample rate converter and changed sample rate
of audio stream from 48 KHz to 16 KHz for XAudio on
Windows Vista.
Windows Vista All
Version 7.40.00
Integration of Windows Vista Speakerphone code
for future builds.
Windows Vista All
Support for HDA modems on nVidia chipsets is
needed in the DOS test.
DOS Nvidia
Japan CID is not detected with Zion boards.
Connect Phone line simulator for CID-4Lines. Open
Hyperterminal and issue AT+GCI=0, AT+VCID=1.
Make a call to Zion and observe it detect RING but
no CID.
Change Phone line simulator for TLS-5, issue
AT+GCI=B5, AT+VCID=1. Make a call to Zion and
observe it detect RING and CID.
All SmartMC3z
When port is open and system goes to S3, Lassen
can not dial after resume from S3.
Windows 2000
Windows XP
AMD64
AC-Link modem with
Intel AC-Link
controller
SmartMC3z
Use a single INF to install both modem and
speakerphone components
Windows Vista All
When modem goes off-hook, a Pop Noise can be
heard so we need to apply 800 ms silent time after
off-hook to remove the pop noise.
All All
Sample Rate Converter is required if audio driver
does not support sample rate of modem stream.
Windows Vista All
Taiwan CID (PreRing DTMF) only works for the first
call. If you drop the line and call again, CID is not
seen. Same scenario repeats after reboot.
Fixed by adding a call to update pre ring indicator at
the end of DTMF CLID which will setup CID RX.
All All
Teton has ring detection issues that were
introduced in 7.33.00.
All Teton
The new Mloader version 2.14 communicates with
the datapumps through Orca function table rather
than the CModem class. Need to add a wrap of C
functions calling the CModem class functions. This
code does not get compiled in the HSF drivers.
All All

Version 7.39.00
On hyper threading or dual core systems, if you run
coldboot.exe several hundred times, it eventually
blue screens in our HSFHWAZL.SYS driver
Windows XP HDAudio
Separate Windows 2000 and Windows XP INFs and
make sure one does not install on the other.
Windows 2000
Windows XP
All
Code added to drive new HAL DC circuit. All HAL products
Do not include strmdisp.sys and Yukon in release
build and update libraries for ORCA.
Windows 2000-
Windows XP-
AMD64
All
Modem Loopback test fails in PC doctor for
Windows for HDA systems
Windows 2000-
Windows XP-
AMD64
HDAudio
Using AT%TT26 (V.32 4800 bps) - AT%TT2A
(V.32bis 14400 bps) the modem generates 1800 Hz
tone rather than a 2400 Hz wide signal. As a result
the modem fails the PTT tests.
Problem found during by EEDC during PTT testing.
All All
Version 7.38.00
Blue screen running Coldboot.exe several hundred
times
Windows 2000-XP HD Audio
Version 7.37.00
Bryce PLL did not start when temperature reached
60C and above
All Bryce
HDAudio driver could not load on Windows 2000 Windows 2000 HDAudio
Version 7.36.00
ULi1573 X64 driver can't support WOR AMD64 HSP
Blacklisting is not working correctly when different
methods are configured.
All All
Blue screen during extended HCT DPE test cycles All
HDAudio dual core or
hyper threading
systems
Bryce and Lassen need OSR252 support All Bryce
Bryce:DTMF level is 8db below expected when
complex impedence bit is set
All Bryce
Cannot dial out with Teton on HDA
Windows 2000-
Windows XP
All
USB driver does not build with Server 2003 DDK
3790
All HSF-USB
WOR fails with SOftRing enabled. Windows XP SmartMC3S
Version 7.35.00
False OCP detection with Bryce All All
INFs needed for HAL products All HAL
No ring detect on ATI platforms All
AC-Link modem with
ATI AC-Link controller
Quanta/Fujitsu GU1 AT+MS upstream issue All All

Voice device fails if BondOption is set for Voice
Windows XP
AMD64
HSFi
Conducted emissions on Bryce\HAL is marginal
with AT%TT6xx (upstream PCM)
All All
Tone detection in voice mode uses the 2nd tone
parameter as bandwidth
All All
Fail to detect some of BUSY & REORDER tones
during CO signals test -voice mode
Windows XP All
Intermittent connect failures of V.23 and Bell-103 All All
Version 7.34.00
CARP crashes on Windows WINDOWS VISTA Windows Vista All
Can not open modem on AMD Dual Core (VIA),
TL21259
All SmartMC3S
OCP false detection and need LCL detection for
daa lib
All All
DMA buffers were not Unmapped after DMA were
closed.
Windows 2000
Windows XP
Win64
HDAudio
ESD failure All All
Failed to open port on 64-bit system with Uli1573 Win64
AC-Link modem with
ALi AC-Link controller
Issues for initial Bryce test All All
Korean Ring Impedence not set All Homer
Need Lassen support All Lassen
Percent TT failure for Bryce All Bryce
Poor CID detection for ZionX2HalX3 All
ZionX2
HALX3
Termination cause from v.42 was not clearly set. All All
Teton Generic INFs All All
Zion/Bryce Tx level is wrong when complex bit is
set in .cty file
All
HAL(Zion
Bryce)
ZionX2/HalX3 Pulse Setup and Flash hook test
failed in EEDC
All
ZionX2
HALX3
n400 was exceeded and caused disconnection
during large file transfer
All All
Failing tests in Belarus: V.22 frequency offset All All
Failing tests in Belarus: V.32 phase jitter All All
Download of a large file failed to complete All All
Random characters are displayed when the user
tries to connect to the server
All SmartMC3S
Version 7.33.00
Can not force modem using COM10 on Windows
XP/2k
Windows 2000
Windows XP
AMD64
All
Need Bryce driver support All All
Slow pulse dialing not working for Hal All All
Country.doc has no HAL updates All All
Version 7.32.00
Enable soft ring detection for all supported chipsets All All
DTMF transmit level 2.5dB too high, lowered by
3dB.
All
SmartMC3S
SmartMC3z
Inf setting change to eliminate speakerphone failure
during HCT 12.1.01.
AMD64 HSFi

Failure seen with previous releases during the NDIS
test. Remote phone mic to PC speaker is silent and
PC Mic to remote phone is silent
Unexpected Generic Country in response to ATI9. All All
Modem fails to detect V.42 (ADP,LAPM) in loop 6. All
All
HSF
Version 7.31.00
False ring detect with Teton(AC 97) on Win98 Win98 Teton
Include support for Teton and update AC97 VIA
support for new VIA Core logic
All
AC-Link modem with
VIA AC-Link controller
Version 7.30.00
DC loop current not compliant in Australia for
SmartMC3z
All All
Australia pulse dialing does not work, China,
Canada pulse dialing out of spec.
All All
HSF USB modem causes system failure with 64 bit
driver during HCT testing
Win64 HSF-USB
Version 7.29.00
Fix HD Audio driver for Teton. Windows 2000-XP Teton-HD Audio
DMA position may be incorrect on VIA VT8237
chips.
All
AC-Link modem with
VIA AC-Link controller
Added support for Zion Windows 2000-XP HD - Audio
Fax page retransmission running HCT on 64 bit ATI
drivers
Windows 2000-XP
AC-Link modem with
Version 7.28.00
HCT fax test failure for SmartMC3s on ATi. Fax test
fails after receiving 3 pages.
64 bit OS
AC-Link modem with
Sometimes the driver reads wrong DMA pointer
and that causes miscellaneous symptoms, i.e.
broken dial tone, no dial tone, etc.
64 bit OS
AC-Link modem with
Fix Korean ring busy/dial tone detection failure.
Add UpdateDACMute in Off hook, since Korean
ring mutes the DAC.
All All
Version 7.27.00
Poor connectivity performance for HDAudio with
Pre-Ring CID is enabled in Taiwan.
Windows 2000
Windows XP
Windows XP64
HDAudio
QC LAPM flag is not correctly received. All All
(DVT) modem fails V92 QC to 3Comhiper server All All
No Quick Connect connection against v.92 server
configured with upstream enabled.
All All

Version 7.26.00
Korean Ring Impedance is not enabled WDM drivers All
Manufacturing Test command: AT|LC Loop Current
test used the wrong format.
WDM drivers All
Line current detection failure on some central
office.
All HSP
Japan redial limitation timeout too long. All All
System crashed in VMM (blue screen) on Win98SE
and WinME during port open.
Windows 98 Second
Edition
Windows Millennium
All
System will freeze when modem goes off-hook
using Win98se with CARP driver when there is no
Audio driver loaded.
98 All
HDAudio modem could not detect dial tone
Windows XP
Windows 2000
HDAudio
UNAA train times (LT) are long, close to 30
seconds, for large portion of UNAA net.
With UNAA detection improvement, we had seen
the train time for U-cases dropped to as close to
those of I-cases.
All All
Intermittent failure to Connect in U-Cases WDM drivers HSFi
Modem fails to prepare CP sequence in time when
there are long Tx buffers (BuffersDelay registry
key) and probably specific RTD round trip delay.
This causes the renegotiation to fail and modem
disconnects.
All All
Fail to connect in U-case during a QC call against
different servers.
All All
Performance degradation against 3Com server U-
case
All All
Version 7.25.00
No 64-bit support for Silicon Labs codec Windows XP64 PcTel
Merged code to support Silab 12khz codec. All PcTel
AT|DMA, AT|PNPID, AT|NE windows manufacturer
test failures in HDAudio
Windows 2000
Windows XP
HDAudio
ISP connect failure during Bench mark test running. All SmartMC3S
Changes for HD Audio DOS test DOS HDAudio
In a Smart Speakerphone configuration, no sound is
heard on the receiving side. The problem is that we
cannot hear playback sounds on the speaker, i.e.
caller's or callee's voice and it is because for HD
Audio, the send and receive are handled as two
different devices.
Windows 2000
Windows XP
HDAudio
Version 7.24.00
USB 64-bit driver failed to connect using pulse
dialing.
AMD64 HSF-USB
HSF USB wdm driver did not load on Win98se.
Corrected by linking to different USB DDK library.
Win9SE WDM
drivers
HSF-USB

Version 7.23.00
Problems Fixed in v7.23.00 Operating System Hardware Platform
No call progress sound was heard with 64bit, or if
CSD\KMixerDataInitialDelay changed from 0x9 to
0xC in the INF, then a truncated sound was heard.
FIFO size increased, and under run detection
handled differently for 64bit. 64bit requires the
KMixerDataInitialDelay to be set to 0xC.
x64 All
In a manufacturing test environment, the port open
was not failing if the DAA module was not
populated.
All SmartDAA
The modem disconnects during ESD test using
MDC1.5. The fix is to block resets. On the notebook
the ground bounces look to the device like reset.
The device reset caused the disconnections.
WDM drivers HDAudio Modem
Specific busy tone cadence failure during some
Central Office testing
All ICH
Occasional blue screen on dial or answer after initial
installation with USB driver.
x64 HSF-USB
EFT testing blue screen fixed by turning off LCL
interrupts.
WDM drivers HDAudio Modem
Version 7.22.00
Public Import Test warnings for HCT12.1
Windows 2000
Windows Millennium
Windows XP
AMD64
All
Blue screens on HCT12.0 Device Path Exerciser
and Driver Verifier NDIS start/stop
Windows 2000
Windows 98 Second
Edition WDM drivers
Windows Millennium
Windows XP
AMD64
HSF-USB
Implement AT|PNPID for HD Audio
Windows 2000
Windows 98 Second
Edition WDM drivers
Windows NT4
Windows XP
AMD64
All
Version 7.21.00
Waikiki X3: Fail to connect in V34 in Answer mode Windows XP All
V.90 support is disabled All All
No V.92 in modem name All All
Waikiki V90 average throughput is > 100 cps lower
in 7.17.00 than in 7.12.09
All All
USB HCT 12.0 Failures Windows XP HSF-USB l
Waikiki X3: V90 Performance degradation Windows XP SmartAMC2
ALI 1563 can't make a V90 connection All
AC-Link modem with
ALi AC-Link
controller

New friendly name without reference to V.92 All All
Modem frequently failed to detect Type 2 CID
(CWCID)
All All
Spartacus X3: Fail to connect in loop6 & 7 in V34 Windows XP SmartMC3S
Version 7.20.00
V.90 support is disabled, only V.34 is supported.
Windows 98 Second
Edition WDM drivers
Windows Millennium
Windows XP
AMD64
All
Default driver should not have any reference to V.92
since it does not support any of the V.92 features.
All All
Known Issues in V7.20.00 Operating System Hardware Platform
Guiu Setup will show 2 devices upon installations on
AC-Link modem with HDAudio PnPID include in the
INF's. That is because the tool we use to scan the
bus (UIUSYS.SYS) doesn't yet know about
HDAUDIO bus devices. This will be resolved and
updated. There is no current impact other than a
misleading failure message regarding the HDAudio
installation when installing on an AC-Link platform.
All
AC-Link and HD
Audio
Un-install/re-install without reboot fails. The
installation fails if you uninstall the modem, and
immediately re-install. We are looking at this issue,
and will resolve it for the next release.
WDM drivers All
OCP does not pop-up on HDAudio platform, ok on
AC-Link when a Digital Line event occurs. This
does not affect the Digital Over Current protection, it
just results in a No Dial tone message as a dial-
termination reason. This will be resolved for the
next release.
All All
Version 7.19.00
Blue screen seen in Driver Verifier (HCT 12) All
SmartHSF
SmartHSFi
SmartHSFs
AT+VCID=1 returns ERROR for countries not
supporting CID causing TAPI dial abort
Windows XP All
Blue screen when AT+VRID is issued
Windows 2000
Windows XP
All
AT| commands are not supported Windows XP
SmartHSF
SmartMC3S
SmartMC3S RevB
SmartAMC2
Fixes for manufacturing test All All
Add voice INFs for SoftRing modems All All
Support standard DDK build
Windows XP
AMD64
All
Asus EFT test failure All SmartMC3z
Conditionally set V.92 settings based on build All All

options
Microsoft prefix warnings.
Windows XP
AMD64
All
FaxTalk engineer see two popup messages when
send .wave file to telephone line.
Windows 98 Second
Edition
All

Homologation/Country File Changes
Master CTY file Updated to v1.28 starting from Modem Driver V7.73.00

Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
None None

Update file
header
Update
header with
year 2008
and update
the list of the
supported
modems by
adding
PCIe, USB,
HDA
modems
Outdated
information
Current
information

Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
Germany All

Not shown in
Modem
properties under
Windows Vista
Create two
identical
profiles with
T.35 codes
0x04 and
0x42
One profile
Two identical
profiles

Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
All profiles
CALL_WAI
TING
Increase Call
Waiting detection
reliability
Use
Response
Time
parameter
and
increase the
value;
increase
On/Off time
Response
Time was
ignored
ResponseTime
(26 -> 42
msec) and
On/Off
Debounce (50 -
> 70 msec).

Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
All profiles
V92_CON
TROL

Enable PCM
Upstream
Disabled Enabled

Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification

South
Africa,
Turkey,
Canada, El
Salvador,
Puerto
Rico, USA
DTMF
SMART_D
TMF

No need to
overwrite profile
values
Remove
entries

Use values
from the
corresponding
profiles

Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
Samoa Name

MS request
Name
change
Western
Samoa
Samoa
Macedonia Name

MS request Name
change
Macedonia
MACEDONIA,
FORMER
YUGOSLAV
REPUBLIC OF
Congo Name

MS request

Name
change
Congo
CONGO,
DEMOCRATIC
REPUBLIC OF
THE
Yugoslavia Name

MS request
Name
Change
Yugoslavia Serbia
Montenegr
o
All

MS request
Creation
T.35 code
0xEA
Master CTY file Updated to v1.20 starting in v7.48.00
Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
All
Cadence
and Tones

Pass
Country
Tester
Numerous
fails
0 fail
Master CTY file Updated to v1.19bis starting in v7.45.00
Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
South
Africa
Smart
TXLevel
Tuning
Change
DTMF level
DTMF
Levels set to
-9/-11 dBm
57,\
3C
DTMF Levels
set to -6/-8
dBm
5D,\
40
Brazil Flags

Add bit for
surge test
...,4C, 00 ...,4C, 08
Taiwan Blacklisting

BL added on
No Dial
Tone and
Busy
HKR,Region
\00FE,BLAC
KLISTING,1,
\
00,\
01,\
00,\
01,\
01,\
HKR,Region\00
FE,BLACKLIST
ING,1,\
01,\
01,\
01,\
01,\
01,\
01,\

01,\
Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
Taiwan
Pulse,
Blacklisting
Test conformity
All to at&p1,
enable BL
Normal &p
mapping, No
BL
All &P mapped
1 and BL
method 2
Australia
SmartTXLev
el
Test conformity
Add pulse
setup
DTMF
Levels set to
-8/-10 dBm
DTMF Levels
set to -6/-8
dBm
2A,\
1C
Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
UAE All
Test conformity
Change to
TBR
reference
Reference
profile set to
01
Reference
Profile set to 02
All TBR
countries
SmartRelay
s bit 7
Wilfrid Request
SmartRelay
s bit 7
Compensati
on bit set
Compensation
bit reset
Ukraine
SmartTXLev
el, TXLevel
TGC request
Same as
Russia
ITU Default
Similar to
Russia (TGC)
South
Africa
SReg
TGC request
S7
S7 default to
57
S7 default set
to 32 (TGC)
Australia Pulse
Offset needed for
test conformity
Add pulse
offset
No section
F0,\
0F,\
Master CTY file Updated to v1.17 for dedicated internal process.
Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
Australia Pulse Test conformity
Add pulse
setup
No section 64
Australia
SmartRelay
s
Test conformity
Bit for very
slow edge
Rmake set
to 300 ohms
HKR,Region
\001E,SMAR
T_RELAYS,
1,\.A4,AC,\
A5,AC,\
A4,AC,\
A4,AC
HKR,Region\00
09,SMART_RE
LAYS,1,\....B4,
AE,\
B5,AE,\
B4,AE,\
A4,AE
Chile
SmartRelay
s
Test conformity
Set third
impedance
600 ohms
No section
reference to
profile 01
HKR,Region\00
25,SMART_RE
LAYS,1,\....in
C0

Belarus
SmartRelay
s
Test conformity DC2 to DC4
HKR,Region
\001E,SMAR
T_RELAYS,
1,\...in 84
HKR,Region\00
1E,SMART_RE
LAYS,1,\....in
8C
Pakistan Sreg Test conformity
Change in
S28 and
S29
No section
HKR,Region\00
84,SREG,1,\
Czech
Rep,
Romania,
Turkey,
Bosnia,
Moldova
All Test conformity
Profile
change to
match
Europe
ITU TBR
French
DOM
TOM
All Test conformity
Profile
change to
match
France
ITU TBR
Netherlan
ds Antilles
All Test conformity
Profile
change to
match
Netherlands
ITU TBR
Taiwan Toneparams Error
Remove
Wrong
parameters
TBR
Country
Parameter
Type
Reasons
Modification
- description
Before
Modification
After
Modification
Saint
Pierre and
Miquelon,
Inmarsat
Name
Flash hook
duration must be
set to 100ms +/-
20 ms according
to the spec
S002_A01_2001.
Changed
S29 from
250ms to
100ms
St Pierre et
Miquelon,
Inmarsat
atlantic east
Saint Pierre
and Miquelon,
Inmarsat
India
SmartRelay
s

Change for
Fast edge in
Pulse dialing
No
SmartRelays
section
SmartRelays
section with...
E4,80,\
E5,80,\
E4,80,\
E4,80
Japan Pulse
Interdigit
84,03,\
Interdigit
EE,02,\
USA CADENCE
Max Busy
58,02,00,00,
\
Max Busy
71,02,00,00,\
Korea FLAGS No bit set
New bit to
set for ring
impedance
Bit 2 Flag 03
FLAGS,1,02,
00,0C,00
FLAGS,1,02,00
,0C,04
ElSalvado
r, Puerto
Rico,
Norway,
USA,
japan
SREG
No S28
specification
default setting
used
No S28
setting
driver
default is
used
Add S28
setting for
clarification
purpose
1C,00,FF,00,\


Xaudio (Soft Call Progress for Windows Vista)
Version 1.0.15.0
Operating
System
Hardware
Platform
Severity
Intermittent blue screen
(SYSTEM_THREAD_EXCEPTION_NOT_HANDLED
(7e)) on a specific system when disconnecting
modem connection using AOL 9.0 Optimized
application.
Windows
Vista
All High
Version 1.0.8.0 1.0.14.0 ACF modem fixes ONLY
Version 1.0.7.0
Operating
System
Hardware
Platform
Severity
Call progress may not stop due to
synchronization issue.
Windows
Vista
All High
Version 1.0.5.0 1.0.6.0 ACF modem fixes ONLY
Version 1.0.4.0
Operating
System
Hardware
Platform
Severity
Blue screen when running DTM NDIS blind
dial test. This fix was a refinement of the fix
done in V1.0.3.0.
Windows
Vista
All High
Version 1.0.3.0
Operating
System
Hardware
Platform
Severity
CPU always stays at 100% maximum
frequency when XAudio is running. This
problem was introduced in internal release
V1.0.2.0.
Windows
Vista
All High
Blue screen when running DTM NDIS blind
dial test. This problem was introduced in
internal release V1.0.2.0.
Windows
Vista
All High

Version 1.0.1.0 and Version 1.0.2.0
Operating
System
Hardware
Platform
Severity
Internal test releases, never shipped
Windows
Vista
All

HSF Release Notes v7.75

Uploaded by

Copyright:

Available Formats

HSF Release Notes v7.75

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HSF Release Notes v7.75

Uploaded by

Copyright:

Available Formats

Copyright 2004-2008 by Conexant Systems.

All rights reserved

You might also like