Galmet Spraypaint Aerosol (all colours except silver)

Chemwatch Material Safety Data Sheet

Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 1 of 9
Section 1 - CHEMICAL PRODUCT ANDCOMPANY IDENTIFICATION
PRODUCTNAME
Galmet Spraypaint Aerosol (all colours except silver)
PROPER SHIPPINGNAME
AEROSOLS
PRODUCTUSE
Application is by spray atomisation from a hand held aerosol pack.
Anti-corrosive and decorative coating.
SUPPLIER
Company: ITWPolymers & Fluids
Address:
100 Hassall Street
Wetherill Park
NSW, 2164
Australia
Telephone: +61 2 9757 8800
Emergency Tel:1800 039 008
Emergency Tel:+61 3 9573 3112
Fax: +61 2 9757 3855
Section 2 - HAZARDS IDENTIFICATION
STATEMENTOFHAZARDOUSNATURE
HAZARDOUS SUBSTANCE. DANGEROUS GOODS. According to the Criteria of NOHSC, and the ADGCode.
RISK SAFETY
Extremely flammable. Keep away from sources of ignition. No smoking.
Irritating to eyes. Do not breathe gas/fumes/vapour/spray.
Risk of explosion if heated under Avoid contact with skin.
confinement.
Harmful: danger of serious damage to health Avoid contact with eyes.
by prolonged exposure through inhalation.
Harmful to aquatic organisms, may cause Wear suitable protective clothing.
long- term adverse effects in the aquatic
environment.
Possible risk of harm to the unborn child. Wear suitable gloves.
Wear eye/face protection.
Use only in well ventilated areas.
Keep container in a well ventilated place.
Avoid exposure - obtain special instructions
before use.
Keep in a cool place.
To clean the floor and all objects contaminated
by this material, use water and detergent.
Keep container tightly closed.
Keep away from food, drink and animal feeding
stuffs.
In case of contact with eyes, rinse with plenty
of water and contact Doctor or Poisons Information
Centre.
If swallowed, IMMEDIATELY contact Doctor or
Poisons Information Centre. (show this container
or label).
This material and its container must be disposed
of as hazardous waste.
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 2 of 9
Section 3 - COMPOSITION/ INFORMATIONONINGREDIENTS
NAME CAS RN %
solvent naphtha petroleum, medium aliphatic 64742-88-7 10-29
toluene 108-88-3 0-9
naphtha petroleum, light aromatic solvent 64742-95-6. 0-9
dimethyl ether 115-10-6 30-60
Section 4 - FIRST AID MEASURES
SWALLOWED
Not considered a normal route of entry.
If spontaneous vomiting appears imminent or occurs, hold patient's head down, lower than their hips to help avoid possible
aspiration of vomitus.
If swallowed do NOT induce vomiting.
If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and
prevent aspiration.
Observe the patient carefully.
Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becoming unconscious.
Avoid giving milk or oils.
Avoid giving alcohol.
EYE
If aerosols come in contact with the eyes:
Immediately hold the eyelids apart and flush the eye continuously for at least 15 minutes with fresh running water.
Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting
the upper and lower lids.
Transport to hospital or doctor without delay.
Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
SKIN
If skin contact occurs:
Immediately remove all contaminated clothing, including footwear.
Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
INHALED
If aerosols, fumes or combustion products are inhaled:
Remove to fresh air.
Lay patient down. Keep warm and rested.
Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid
procedures.
If breathing is shallow or has stopped, ensure clear airway and apply resuscitation, preferably with a demand valve
resuscitator, bag-valve mask device, or pocket mask as trained. PerformCPR if necessary.
NOTESTOPHYSICIAN
Treat symptomatically.
Section 5 - FIRE FIGHTINGMEASURES
EXTINGUISHINGMEDIA
SMALL FIRE:
Water spray, dry chemical or CO2
LARGE FIRE:
Water spray or fog.
FIRE FIGHTING
Alert Fire Brigade and tell them location and nature of hazard.
May be violently or explosively reactive.
Wear breathing apparatus plus protective gloves.
Prevent, by any means available, spillage from entering drains or water course.
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 3 of 9
Section 5 - FIRE FIGHTINGMEASURES
FIRE/EXPLOSIONHAZARD
Liquid and vapour are highly flammable.
Severe fire hazard when exposed to heat or flame.
Vapour forms an explosive mixture with air.
Severe explosion hazard, in the form of vapour, when exposed to flame or spark.
Other combustion products include: carbon dioxide (CO2), nitrogen oxides (NOx).
FIRE INCOMPATIBILITY
Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may
result.
HAZCHEM
2YE
Section 6 - ACCIDENTAL RELEASE MEASURES
MINOR SPILLS
Clean up all spills immediately.
Avoid breathing vapours and contact with skin and eyes.
Wear protective clothing, impervious gloves and safety glasses.
Shut off all possible sources of ignition and increase ventilation.
MAJOR SPILLS
Clear area of personnel and move upwind.
Alert Fire Brigade and tell them location and nature of hazard.
May be violently or explosively reactive.
Wear breathing apparatus plus protective gloves.
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
Section 7 - HANDLINGANDSTORAGE
PROCEDUREFORHANDLING
Avoid all personal contact, including inhalation.
Wear protective clothing when risk of exposure occurs.
Use in a well-ventilated area.
Prevent concentration in hollows and sumps.
SUITABLECONTAINER
Aerosol dispenser.
Check that containers are clearly labelled.
STORAGEINCOMPATIBILITY
Avoid storage with oxidisers.
STORAGEREQUIREMENTS
Keep dry to avoid corrosion of cans. Corrosion may result in container perforation and internal pressure may eject contents of
can.
Store in original containers in approved flammable liquid storage area.
DO NOT store in pits, depressions, basements or areas where vapours may be trapped.
No smoking, naked lights, heat or ignition sources.
Keep containers securely sealed. Contents under pressure.
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURECONTROLS
Source Material TWA TWA STEL STEL Peak Peak TWA Notes
ppm mg/m ppm mg/m ppm mg/m F/CC
__________ __________ ______ ______ ______ ______ ______ ______ ______ ______
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 4 of 9
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Source Material TWA TWA STEL STEL Peak Peak TWA Notes
ppm mg/m ppm mg/m ppm mg/m F/CC
__________ __________ ______ ______ ______ ______ ______ ______ ______ ______
Australia solvent naphtha 900 (see Chapter 16)
Exposure petroleum,
Standards medium aliphatic
(Petrol
(gasoline))
Australia toluene 50 191 150 574 Sk
Exposure (Toluene)
Standards
Australia dimethyl ether 400 760 500 950
Exposure (Dimethyl ether)
Standards
MATERIALDATA
DIMETHYL ETHER:
NAPHTHA PETROLEUM, LIGHT AROMATIC SOLVENT:
SOLVENT NAPHTHA PETROLEUM, MEDIUM ALIPHATIC:
Sensory irritants are chemicals that produce temporary and undesirable side-effects on the eyes, nose or throat.
Historically occupational exposure standards for these irritants have been based on observation of workers' responses to various
airborne concentrations.
NAPHTHA PETROLEUM, LIGHT AROMATIC SOLVENT:
SOLVENT NAPHTHA PETROLEUM, MEDIUM ALIPHATIC:
Odour threshold: 0.25 ppm.
The TLV-TWA is protective against ocular and upper respiratory tract irritation and is recommended for bulk handling of
gasoline based on calculations of hydrocarbon content of gasoline vapour.
GALMET SPRAYPAINT AEROSOL (ALL COLOURS EXCEPT SILVER):
Not available
SOLVENT NAPHTHA PETROLEUM, MEDIUM ALIPHATIC:
NOTE L: The classification as a carcinogen need not apply if it can be shown that the substance contains less than 3%DMSO
extract as measured by IP 346. European Union (EU) List of Dangerous Substances (Annex I) - up to the 29th ATP.
REL TWA: 110 ppm [Manufacturer]
CEL TWA: 110 ppm, 500 mg/m3
TOLUENE:
For toluene:
Odour Threshold Value: 0.16-6.7 (detection), 1.9-69 (recognition)
NOTE: Detector tubes measuring in excess of 5 ppm, are available.
High concentrations of toluene in the air produce depression of the central nervous system(CNS) in humans.
Exposure limits with "skin" notation indicate that vapour and liquid may be absorbed through intact skin. Absorption by skin
may readily exceed vapour inhalation exposure. Symptoms for skin absorption are the same as for inhalation. Contact with eyes and
mucous membranes may also contribute to overall exposure and may also invalidate the exposure standard.
NAPHTHA PETROLEUM, LIGHT AROMATIC SOLVENT:
REL TWA: 25-100 ppm*, 125 mg/m3* [Various Manufacturers]
CEL TWA: 50 ppm, 125 mg/m3
DIMETHYL ETHER:
for dimethyl ether:
The no-effect-level for dimethyl ether is somewhere between 2000 ppm (rabbits) and 50,000 ppm (humans) with possible cardiac
sensitisation occurring around 200,000 ppm (dogs). The AIHA has adopted a safety factor of 100 in respect to the 50,000 ppm level
in its recommendation for a workplace environmental exposure level (WEEL) which is thought to protect against both narcotic and
sensitising effects.
May act as a simple asphyxiants; these are gases which, when present in high concentrations, reduce the oxygen content in air
below that required to support breathing, consciousness and life; loss of consciousness, with death by suffocation may rapidly
occur in an oxygen deficient atmosphere.
CARE: Most simple asphyxiants are odourless or possess low odour and there is no warning on entry into an oxygen deficient
atmosphere.
PERSONAL PROTECTION
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 5 of 9
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
RESPIRATOR
Type AX Filter of sufficient capacity. (AS/NZS 1716 & 1715, EN 143:2000 & 149:2001, ANSI Z88 or national equivalent)
EYE
No special equipment for minor exposure i.e. when handling small quantities.
OTHERWISE: For potentially moderate or heavy exposures:
Safety glasses with side shields.
NOTE: Contact lenses pose a special hazard; soft lenses may absorb irritants and ALL lenses concentrate them.
HANDS/FEET
No special equipment needed when handling small quantities.
OTHERWISE:
For potentially moderate exposures:
Wear general protective gloves, eg. light weight rubber gloves.
OTHER
No special equipment needed when handling small quantities.
OTHERWISE:
Overalls.
Skin cleansing cream.
Eyewash unit.
Do not spray on hot surfaces.
ENGINEERINGCONTROLS
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed
engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions to
provide this high level of protection.
The basic types of engineering controls are:
Process controls which involve changing the way a job activity or process is done to reduce the risk.
Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation
that strategically "adds" and "removes" air in the work environment.
Section 9 - PHYSICAL ANDCHEMICAL PROPERTIES
APPEARANCE
Supplied as an aerosol pack. Contents under PRESSURE.
Coloured liquid with a solvent odour; does not mix with water.
PHYSICAL PROPERTIES
Liquid.
Gas.
Does not mix with water.
Floats on water.
State Liquid Molecular Weight Not Available
Melting Range (C) Not Available Viscosity Not Available
Boiling Range (C) - 24.84 Solubility in water (g/L) Immiscible
Flash Point (C) - 41.1 pH (1%solution) Not Applicable
Decomposition Temp (C) Not Available pH (as supplied) Not Applicable
Autoignition Temp (C) 296 Vapour Pressure (kPa) 520 @21.1C
Upper Explosive Limit (%) 27.0 Specific Gravity (water=1) 0.98 @20C
Lower Explosive Limit (%) 3.4 Relative Vapour Density >1
(air=1)
Volatile Component (%vol) >60 Evaporation Rate 0.14 BuAC = 1
toluene
log Kow (Sangster 1997): 2.73
dimethyl ether
log Kow (Sangster 1997): 0.1
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 6 of 9
Section 10 - STABILITY AND REACTIVITY
CONDITIONSCONTRIBUTINGTOINSTABILITY
Elevated temperatures.
Presence of open flame.
Product is considered stable.
Hazardous polymerisation will not occur.
For incompatible materials - refer to Section 7 - Handling and Storage.
Section 11 - TOXICOLOGICAL INFORMATION
POTENTIALHEALTHEFFECTS
ACUTEHEALTHEFFECTS
SWALLOWED
Not normally a hazard due to physical form of product.
Considered an unlikely route of entry in commercial/industrial environments. The liquid may produce gastrointestinal discomfort
and may be harmful if swallowed. Ingestion may result in nausea, pain and vomiting. Vomit entering the lungs by aspiration may
cause potentially lethal chemical pneumonitis.
EYE
The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to
irritants may produce conjunctivitis.
SKIN
The material may cause skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling,
the production of vesicles, scaling and thickening of the skin.
INHALED
Inhalation of high concentrations of gas/vapour causes lung irritation with coughing and nausea, central nervous depression
with headache and dizziness, slowing of reflexes, fatigue and inco-ordination.
If exposure to highly concentrated solvent atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma and
possible death.
WARNING:Intentional misuse by concentrating/inhaling contents may be lethal.
CHRONICHEALTHEFFECTS
Chronic solvent inhalation exposures may result in nervous systemimpairment and liver and blood changes. [PATTYS].
Constant or exposure over long periods to mixed hydrocarbons may produce stupor with dizziness, weakness and visual disturbance,
weight loss and anaemia, and reduced liver and kidney function. Skin exposure may result in drying and cracking and redness of
the skin. Chronic exposure to lighter hydrocarbons can cause nerve damage, peripheral neuropathy, bone marrow dysfunction and
psychiatric disorders as well as damage the liver and kidneys.
TOXICITYANDIRRITATION
Not available. Refer to individual constituents.
CARCINOGEN
Toluene International Agency for Group 3
Research on Cancer (IARC) -
Agents Reviewed by the IARC
Monographs
REPROTOXIN
toluene ILO Chemicals in the electronics industry Reduced fertility or
that have toxic effects on reproduction sterility
SKIN
toluene Australia Exposure Notes Sk
Standards - Skin
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 7 of 9
Section 12 - ECOLOGICAL INFORMATION
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
This material and its container must be disposed of as hazardous waste.
Ecotoxicity
Ingredient Persistence: Persistence: Air Bioaccumulation Mobility
Water/Soil
solvent naphtha petroleum, No Data No Data
medium aliphatic Available Available
toluene LOW MED LOW MED
naphtha petroleum, light No Data No Data
aromatic solvent Available Available
dimethyl ether LOW No Data LOW HIGH
Available
Section 13 - DISPOSAL CONSIDERATIONS
Consult State Land Waste Management Authority for disposal.
Discharge contents of damaged aerosol cans at an approved site.
Allow small quantities to evaporate.
DO NOT incinerate or puncture aerosol cans.
Section 14 - TRANSPORTATION INFORMATION
Labels Required: FLAMMABLE GAS
HAZCHEM:
2YE (ADG7)
Land Transport UNDG:
Class or division 2.1 Subsidiary risk: None
UNNo.: 1950 UNpacking group: None
Shipping Name:AEROSOLS
Air Transport IATA:
ICAO/IATA Class: 2.1 ICAO/IATA Subrisk: None
UN/ID Number: 1950 Packing Group: -
Special provisions: A145
Shipping name:AEROSOLS
Maritime Transport IMDG:
IMDG Class: 2 IMDG Subrisk: SP63
UNNumber: 1950 Packing Group: None
EMS Number: F-D,S-U Special provisions: 63 190 277 327 344 959
Limited Quantities: See SP277
Shipping name:AEROSOLS
Section 15 - REGULATORY INFORMATION
POISONS SCHEDULE
S5
REGULATIONS
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 8 of 9
Section 15 - REGULATORY INFORMATION
Regulations for ingredients
solvent naphtha petroleum, mediumaliphatic (CAS: 64742-88-7) is found on the following
regulatory lists;
"Australia Exposure Standards", "Australia Hazardous Substances", "Australia High Volume Industrial Chemical List (HVICL)",
"Australia Inventory of Chemical Substances (AICS)", "Australia Standard for the Uniform Scheduling of Medicines and Poisons
(SUSMP) - Appendix E (Part 2)", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5",
"GESAMP/EHS Composite List - GESAMP Hazard Profiles", "IMO IBC Code Chapter 17: Summary of minimum requirements", "IMO
Provisional Categorization of Liquid Substances - List 3: (Trade-named) mixtures containing at least 99% by weight of components
already assessed by IMO, presenting safety hazards", "International Agency for Research on Cancer (IARC) - Agents Reviewed by
the IARC Monographs", "International Council of Chemical Associations (ICCA) - High Production Volume List", "International
Fragrance Association (IFRA) Survey: Transparency List", "International Maritime Dangerous Goods Requirements (IMDG Code) -
Substance Index", "OECD List of High Production Volume (HPV) Chemicals", "OSPAR List of Chemicals for Priority Action", "OSPAR
National List of Candidates for Substitution Norway"
toluene (CAS: 108-88-3) is found on the following regulatory lists;
"Australia - Australian Capital Territory - Environment Protection Regulation: Ambient environmental standards (AQUA/1 to 6 - non-
pesticide anthropogenic organics)", "Australia - Australian Capital Territory - Environment Protection Regulation: Ambient
environmental standards (Domestic water supply - organic compounds)", "Australia - Australian Capital Territory - Environment
Protection Regulation: Pollutants entering waterways taken to cause environmental harm (Aquatic habitat)", "Australia -
Australian Capital Territory - Environment Protection Regulation: Pollutants entering waterways taken to cause environmental harm
(Domestic water supply quality)", "Australia Customs (Prohibited Exports) Regulations 1958 - Schedule 9 Precursor substances -
Part 2", "Australia Exposure Standards", "Australia Hazardous Substances", "Australia High Volume Industrial Chemical List
(HVICL)", "Australia Illicit Drug Reagents/Essential Chemicals - Category III", "Australia Inventory of Chemical Substances
(AICS)", "Australia National Pollutant Inventory", "Australia Standard for the Uniform Scheduling of Medicines and Poisons
(SUSMP) - Appendix E (Part 2)", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Appendix F
(Part 3)", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Appendix I", "Australia Standard for
the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5", "Australia Standard for the Uniform Scheduling of
Medicines and Poisons (SUSMP) - Schedule 6", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) -
Schedule 7", "GESAMP/EHS Composite List - GESAMP Hazard Profiles", "IMO IBC Code Chapter 17: Summary of minimum requirements",
"IMO MARPOL 73/78 (Annex II) - List of Noxious Liquid Substances Carried in Bulk", "IMO Provisional Categorization of Liquid
Substances - List 3: (Trade-named) mixtures containing at least 99%by weight of components already assessed by IMO, presenting
safety hazards", "International Agency for Research on Cancer (IARC) - Agents Reviewed by the IARC Monographs", "International
Fragrance Association (IFRA) Standards Prohibited", "International Fragrance Association (IFRA) Survey: Transparency List", "OECD
List of High Production Volume (HPV) Chemicals", "OSPAR List of Chemicals for Priority Action", "United Nations Convention
Against Illicit Traffic in Narcotic Drugs and Psychotropic Substances - Table II", "United Nations List of Precursors and
Chemicals Frequently used in the Illicit Manufacture of Narcotic Drugs and Psychotropic Substances Under International Control
(Red List) - Table II", "WHO Guidelines for Drinking-water Quality - Guideline values for chemicals that are of health
significance in drinking-water"
naphtha petroleum, light aromatic solvent (CAS: 64742-95-6) is found on the following
regulatory lists;
"Australia Exposure Standards", "Australia Hazardous Substances", "Australia High Volume Industrial Chemical List (HVICL)",
"Australia Inventory of Chemical Substances (AICS)", "Australia Standard for the Uniform Scheduling of Medicines and Poisons
(SUSMP) - Appendix E (Part 2)", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5",
"GESAMP/EHS Composite List - GESAMP Hazard Profiles", "IMO IBC Code Chapter 17: Summary of minimum requirements", "IMO
Provisional Categorization of Liquid Substances - List 3: (Trade-named) mixtures containing at least 99% by weight of components
already assessed by IMO, presenting safety hazards", "International Agency for Research on Cancer (IARC) - Agents Reviewed by
the IARC Monographs", "International Council of Chemical Associations (ICCA) - High Production Volume List", "International
Fragrance Association (IFRA) Survey: Transparency List", "International Maritime Dangerous Goods Requirements (IMDG Code) -
Substance Index", "OECD List of High Production Volume (HPV) Chemicals", "OSPAR List of Chemicals for Priority Action", "OSPAR
National List of Candidates for Substitution Norway"
dimethyl ether (CAS: 115-10-6, 157621-61-9) is found on the following regulatory lists;
"Australia Exposure Standards", "Australia Hazardous Substances", "Australia Inventory of Chemical Substances (AICS)", "Australia
National Pollutant Inventory", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Appendix E (Part
2)", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5", "IMO IBC Code Chapter 17:
Summary of minimum requirements", "International Council of Chemical Associations (ICCA) - High Production Volume List",
"International Fragrance Association (IFRA) Survey: Transparency List", "OECD List of High Production Volume (HPV) Chemicals"
No data for Galmet Spraypaint Aerosol (all colours except silver) (CW: 5141-44)
Section 16 - OTHER INFORMATION
INGREDIENTSWITHMULTIPLECASNUMBERS
Ingredient Name CAS
dimethyl ether 115-10-6, 157621-61-9
continued...
Galmet Spraypaint Aerosol (all colours except silver)
Chemwatch Material Safety Data Sheet
Issue Date: 15-Nov-2011 CHEMWATCH5141-44
X9317SP Version No:2.0
Page 9 of 9
Section 16 - OTHERINFORMATION
Classification of the preparation and its individual components has drawn on official and authoritative sources as well as
independent review by the Chemwatch Classification committee using available literature references.
A list of reference resources used to assist the committee may be found at:
www.chemwatch.net/references.
The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether
the reported Hazards are Risks in the workplace or other settings.
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or
criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written
permission fromCHEMWATCH. TEL (+61 3) 9572 4700.
Issue Date: 15-Nov-2011
Print Date: 16-May-2012
This is the end of the MSDS.