Air Cadet Publication: Navigation

Download as pdf or txt
Download as pdf or txt
You are on page 1of 68

air cadet publication

ACP 32
navigation
volume 1 - map reading
C
O
M
B
I
N
E
D
C
A
D
ET
F
O
R
C
E
Uncontrolled copy not subject to amendment
Revision 1.00
Amendment List Date
Amended by Incorporated
No Date
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
i
Crown Copyright 2007
Uncontrolled copy not subject to amendment
Revision 1.00
Chapter 1 ................ What is a Map?
Chapter 2 ................ Map Language
Chapter 3 ................ Scales
Chapter 4 ................ Grid References
Chapter 5 ................ Relief
Chapter 6 ................ Gradients
CONTENTS
ACP 32
NAVIGATION
ii
ISSUED 1999
Volume 1................. Map reading
Volume 2 ................. Basic Navigation
Volume 3 ................. Air Navigation
Volume 4 ................. Pilot Navigation
Volume 1
Map Reading
Uncontrolled copy not subject to amendment
Revision 1.00
iii
Uncontrolled copy not subject to amendment
Revision 1.00
WHAT IS A MAP?
CHAPTER 1
32.1.1-1
Why do we need maps?
WHAT IS A MAP?
Introduction
1. Even from the earliest days the urge for man to explore has been great. The
early travellers used natural features to help them find their way from place to place.
By noting the position of the stars, the moon and the sun, man devised a method of
finding out where he was. This meant exploration past known boundaries was now
possible. As the explorer ventured further and further from home and recognisable
features disappeared, he would often sketch his surroundings so that the way home
could be found more easily. These early maps where often drawn on animal hide,
stone or reed paper.
2. If we think of the earth as a sphere, we can imagine how it could be covered
with imaginary lines to help pinpoint a position on the surface. First of all the earth
has an axis, running from the True North pole to the True South pole - the only 2
points on earth that do not rotate. Next, imagine a line that runs around the middle
of the earth half way between the North and South poles- this circular line is called
the equator.
Finding your position
on the earth
Fig 1-1 13th Century
Britain (courtesy of the
British Library)
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 1
32.1.1-2
Prime Meridian
Lines of Longitude
3. If we add more lines running parallel to the equator, they will also be circular,
though smaller than the equator; they are called lines of latitude. Lines on the Earths
surface drawn from pole to pole are called lines of longitude.
Longitude
4. Longitude lines, also called meridians, are circular. They are numbered and
have a starting point at Greenwich in England. This line is numbered zero and
called the prime meridian- all other lines are either east or west of it. Every meridian
- from one pole to the other - is a semi-circle, and has an anti-meridian on the
opposite side of the earth. A meridian and its anti-meridian together make a full
circle round the earth.
5. By numbering the lines, it means that the whole of the earth can be covered.
The position of each line is expressed in degrees away from the prime meridian.
For example in the diagram point A is about 20 (degrees) west of the prime
meridian. Point B is about 40 east of the prime meridian. Although this system
can give reasonably accurate positioning it is not accurate enough for everyday
use, so each degree is further broken down into 60 minutes. This now gives us a
system of describing a points location in terms of degrees and minutes either east
or west of the prime meridian (Greenwich).
Latitude
6. Lines of latitude are circles drawn around the earth, parallel to the equator.
The equator, at zero degrees, splits the earth into two halves, the northern
hemisphere and southern hemisphere. Using the lines of latitude you can descibe
any points location in degrees and minutes either north or south of the equator.
Degrees and minutes
Lines of Latitude
Fig 1-2 Lines of Longitude
NORTH POLE
NORTH LATITUDE
EQUATOR
SOUTH LATITUDE
SOUTH POLE
NORTH POLE
SOUTH POLE
GREENWICH
PRIME
MERIDIAN
Fig 1-3 Lines of Latitude
Uncontrolled copy not subject to amendment
Revision 1.00
WHAT IS A MAP?
32.1.1-3
Recording your
position
7. The parallels of latitude are often drawn at 15 intervals covering the globe,
although other intervals may be chosen. The examples in Fig 1-3 show point A to
be 15 north, point B to be 30 south and point C to be 20 north.
Recording a Position
8. If you put the latitude and longitude lines together on the same globe you will
get a matrix. With this system you can give a points exact position by stating its
latitude, followed by its longitude in degrees and minutes. For example point A
would be at 20N 056W, point B at 17S 017W and point C at 45N 015E.
Note that Latitude must always be given first and that Latitude is always expressed
with 2 figures and Longitude with 3.
Curved or Flat
9. Since the world is curved a truly representative map would also need to be
curved. This would be too difficult for normal use so the curved surface of the earth
is flattened out to fit on to a sheet of paper. This means that there are some
differences between a map and the actual ground it represents. If however, only
small areas of ground are considered when map making, these errors are reduced
to a negligible amount. The need for accurately drawn maps gave rise to the art of
cartography (map making).
10. This art has now become a science where today, every area of ground is
covered either by survey or by satellite to give up-to-date maps of the world.
Ordnance Survey
11. The UK is fortunate because it is served by possibly the best cartographers
anywhere. The Ordnance Survey (OS) is a Government department based in
The curved surface of
the earth is flattened to
fit on paper
Maps are made using
satellites
M726 series map
NORTH POLE
SOUTH POLE
Fig 1-4 Latitude and
Longitude matrix
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 1
32.1.1-4
Topographical maps
Southampton and produced its first map in 1791 for the Army (hence ordnance).
These maps were initially 1 inch to 1 mile (M722 series) and it took 190 sheets to
cover the UK. OS are constantly up-dating the information and map availability. At
this time there are 204 sheets in the Metric 726 Series 1:50,000 covering the whole
of the UK. OS have done a very good job producing this series and you should find
them easy to use. It is this map series that the Air Training Corps use most and will
be the main reference in this publication.
What Do You Want From A Map?
12. If you need to get from A to B it is important that you find the best route so that
you can avoid rivers, lakes, motorways and other such obstacles. By the end of this
publication you should be able to interpret (read) a map, that will include:
Symbols
Grid references
Distances
Most of the basic work can be carried out in the classroom but getting familiar with
the map and what it tells you is the first priority.
13. The M726 Series is classed as a topographical map which means that it
particularly shows the shape and surface detail of the land, including natural and
man-made features. A typical map would show:
Rivers Valleys Hills
Streams Woods
Mountains Marshes
14. Man-made features would include:
Roads Canals
Railways Towns
Villages Power lines
Uncontrolled copy not subject to amendment
Revision 1.00
WHAT IS A MAP?
32.1.1-5
15. The M726 Series is not the only type of map available, there are maps for
several other user groups, including:
a. Administrative maps (eg. for population surveys or council boundaries)
b. Historical maps (giving details on layout of monuments and buildings).
c. Marine maps (estuaries, sandbanks or wrecks).
d. Road maps (motorist route planning).
e. Outline maps (giving very brief description of specific area).
Map Selection
Which map to use?
16. The map you will require will depend on your activity. Here are some of the
choices available:
SCALE POSSIBLE USES
1: 10,000 (1cm = 100m) Orienteering, town planning
1: 25,000 (1cm = 250m) Walking (you may need more
than one)
1: 50,000 (1cm = 500m) Walking (most popular)
1: 63,360 (1inch = 1 mile) Walking (replaced by 1: 50,000)
1: 100,000 (1cm = 1,000m) Cycling, hostelling, route planning
1: 250,000 (1cm = 2,500m) Cycling , motoring, flying
1: 1,000,000 (1cm = 10km) Long distance air navigation
Remember - the larger the number on the right hand side of the scale ratio, the
larger the area covered and so less detail.
Types of maps
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.1-6
Use the latest revision
CHAPTER 1
17. The most popular maps that are used by walkers are:
a. Landranger series (OS) 1: 50,000
b. Outdoor Leisure (OS) 1: 25,000
c. Tourist (OS) 1: 63,360 or 2.5 cm :1 Mile
18. The detail required on a map will depend on the area being covered. An area
which is small is best served with a very detailed map but if touring in a car a less
detailed map is more useful.
Revision (the latest edition)
19. A map is most accurate on the day that it is produced and will continue to be
accurate until the features on it are changed. If you had planned an expedition in
the classroom then went to the start point to find the valley had been dammed and
the river is now a reservoir, this could prove to be a heavy dampener on the walk
and your enjoyment. Some maps may stay fairly constant - for example, those of
mountainous areas, as it takes many years to erode mountains and the area is not
likely to be developed. You must be aware of urban areas like towns and villages
because they can grow or have road bypasses built. Maps covering these areas
may therefore change frequently. Before you start check the revision date of the
map you are about to use.
Looking After Your Map
20. Some maps are now produced laminated (plastic covered) and you can also
treat maps with a waterproof coating. You may decide to protect your map by using
a map case, clear map holder or even a plastic bag. Whatever method you choose
you must always take care of your map. Always keep your map folded because in
high winds you may lose control of it (flapping around) or lose it altogether. NEVER
mark a map surface with ink as this will damage the surface when you try to remove
the mark. If you need to mark a map use a soft pencil and use it very lightly so the
marks can be removed easily with a soft clean eraser. Try to avoid getting your map
wet but if it does then allow the map to dry naturally at the earliest possible chance.
Remember maps are expensive - treat them with care.
NEVER mark maps
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.1-7
Folding your map
WHAT IS A MAP?
Fig 1-5 Folding your map
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 1
32.1.1-8
Do not mark the paper
in any way - write your
answers on a separate
piece of paper, in the
form of a sentence.
Sample Questions
1. Which of these best describes a topographical map? It shows:
a. The shape and surface detail of the land
b. Underlying geological features
c. The distribution of climates
d. The distribution of minerals
2. The Series M726, 1:50,000 maps are:
a. Geological
b. Synoptic
c. Topographical
d. Demographical
3. Which one of these maps shows the greatest detail:
a. 1:25,000
b. 1:250,000
c. 1:500,000
d. 1:1,000,000
4. How should a map be folded so that it does not suffer too much damage in
use and yet ensures the maximum area of map is accessible for reference?
a. Fold back each of the four edges until the piece required is exposed
b. Fold into four equal quarters
c. Fold up from the bottom concertinawise
d. Fold in half length wise with the outwards, then concertinawise
Uncontrolled copy not subject to amendment
Revision 1.00
MAP LANGUAGE
32.1.2-1
CHAPTER 2
MAP LANGUAGE
Introduction
1. The first time you look at a map it will probably be very confusing. It will no
doubt take you a while to understand what is on the sheet and how it gives you
information. Make sure you have a Series M726, 1:50,000 map to look at while you
are working through this chapter. Outside of the main grid, in the margins, there is
a host of useful information and in this chapter you will find a breakdown of whats
what. Whether you are in the classroom or out in the field, if in doubt look in the
margin.
Elevation
2. When you are using a map you must first check the units of height or elevation.
They will either be in feet or metres. In older maps the units of elevation are normally
in feet, so to avoid confusion, check. The units of elevation are displayed on the
map in the top left hand corner, key position 1 in the diagram. It is essential when
you are calculating timings that you know the correct units of height.
Check the units of
height
KEY
1. Units of elevation (Metres)
2. Grid Magnetic Angle
3. Degrees and minutes of longitude
4. Map title
5. Sheet Identification
6. Conventional signs
7. How to give a grid reference
8. Height conversion
9. Adjoining sheet details
10. North points
11. Compilation and revision
12. Deviation of contours
13. Scale and scale lines
14. Grid numbers (eastings)
15. Degrees and minutes of latitude
16. Grid numbers (northings)
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 2
32.1.2-2
Latitude/Longitude
3. The lines of latitude are expressed in degrees and minutes and are marked
along the right and left (east and west) hand side of the map in key position 15. The
lines of longitude are marked along the top and bottom (north and south) of the
map in key position 3. The lines of latitude and longitude are not actually drawn on
the map itself- it would be too confusing.
4. In map reading there are always references to north. There are in fact 3
norths:
a. True north
b. Grid north
c. Magnetic north
True North
5. This is the geographical north pole of the earth - the point where the earths
axis meet the surface.
Grid North
6. This north takes its name from the National Grid system, a system of imaginary
lines drawn vertically and horizontally which divide your map into a series of squares.
Because grid lines are drawn on a flat map and not on the curved surface of the
earth as are the lines of latitude and longitude, the two systems are different. This
difference is shown on the map, key position 10, as a difference between true north
and grid north.
Magnetic North
7. Magnetic north is the point where a magnetic needle will align itself if freely
suspended. The earth has its own magnetic field, similar to that produced by a
giant bar magnet running along the earths axis. Unfortunately, the earths north
and south magnetic poles do not coincide with the geographical poles - in fact they
are about 1200 miles apart!
Information on Latitude
and Longitude
3 Norths
Uncontrolled copy not subject to amendment
Revision 1.00
MAP LANGUAGE
32.1.2-3
Map Identification
8. On the M726 Series of maps the identification box is found at key position
5, at both the top and bottom of the right hand column. This gives details such as:
a. SERIES M726 (type and scaling of map)
b. SHEET 139 (particular area covered by map)
c. EDITION 6-GSGS (Geographical Section General Staff,
Authority in UK)
9. There will be times when the information in this box will change. The most
noticeable change will be the edition number. You may also find the adjoining sheet
information useful if you are not quite sure of the sheet number you require.
Title
10. In the top right hand area of the column you will find the title of the sheet at
key position 4. This will be a rough guide to the area covered by the map. For
example: Birmingham, Grantham, East Kent and Black Mountains.
Scale and Scale Lines
11. The scales are situated along the bottom of the sheet at key position 13 and
they give you: distances in nautical miles, statute miles and kilometres.
A nautical mile = 6076.1 feet = 1.85km
A statute mile = 1760 yrds = 1.6093 km
A kilometre = 0.6214 mile or 5/8 of a mile
12. These scales can be used to obtain measurements for calculations of
distances when route planning in the field.
How to identify your
map
What does GSGS stand
for?
Where are scale lines
on your map?
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 2
32.1.2-4
Revision
13. The revision date is an important feature on a map because it gives the
user an idea how up-to-date it is. The revision date can be found under the heading
COMPILATION AND REVISION which is in the lower quarter of the right hand
column at key position 11. The date will tell when the last set of changes to effect
the map were added. Changes include such things as: new motorways, major
industrial developments or new housing estates.
The Map
14. Having checked all the information and ensured that you have chosen the
correct map, you are now ready to take a closer look at the main grid to see what it
tells you.
15. When a map maker compiles information to put on to a map the aim is to give
an accurate representation of what is on the ground. An aerial photograph of an
area the same size as your map, would not give you all the information you require
and would not be very clear. A map improves on an aerial photograph by using a
set of convenient signs and symbols (a kind of shorthand depicting features on the
ground). After a little practice using these signs and symbols you will soon find it
quite easy to read a map and interpret what you see.
General Features
16. You must be able to SEE what is on a map and know what the features
would actually look like if you were standing in front of them. To help you in this,
some of these features are graded to signify the degree of importance they hold.
Sometimes the same symbol is shown in different colours to signify a difference; for
example, red National Trust symbols show the area is open all year, whilst the
same symbol in blue indicates it has a restricted opening period. It is worth noting
that if a feature is fenced-in then it will have a solid line on the map but if it is a
natural boundary it will have a broken line around it.
Triangulation Points
17. Surveyors build up a map from a large number of triangles. The angles that
are calculated from field work go into giving an accurate measurement on the ground.
Which revision is best?
Trig points
Uncontrolled copy not subject to amendment
Revision 1.00
GENERAL FEATURES
BOUNDARIES
Electricity transmission line
(with pylons spaced conventionally)
Pipe line
(arrow indicates direction of flow)
Buildings
Quarry
Radio or TV mast
with tower
with spire
Church
or
Chapel
Chimney or tower
Glasshouse
Heliport
Windpump
Windmill with or without sails
Triangulation pillar
Graticule intersection at 5' intervals
without tower or spire
Spoil heap, refuse tip or dump
ruin
Public buildings (selected)
Bus or coach station
Coniferous wood
Non-coniferous wood
Mixed wood
Orchard
Park or ornamental grounds
National
County, Region
or Islands Area
District London Borough
National Park
or Forest Park
Forestry Commission
National Trust
always open
opening restricted
Pedestrians only
observe local signs
NT
NT
FC
NT
H
MAP LANGUAGE
32.1.2-5
The points from where this information is taken are called triangulation points (trig
points). Trig points are actually small concrete pillars with a 3 channelled plate on
top. On the map they are shown as a small blue triangle with a dot in the middle
with its height printed next to it (to the nearest metre).
Conventional signs
Uncontrolled copy not subject to amendment
Revision 1.00
Not necessarily rights of way
ROADS AND PATHS
M1
Elevated Service area
Motorway (dual carriageway)
Motorway under construction
Junction number
Unfenced
Sans clture
Dual carriageway
Main road
A 45 (T)
A 1071
Footbridge
Trunk road
1
S
Uneingehegt
Main road under construction
Secondary road
Narrow road with passing places
B 1078
A 855 B 885
Road generally more than 4 m wide
Road generally less than 4 m wide
Other road, drive or track
Gates
Path
Ferry (passenger)
Footpath
Bridleway
Danger Area MOD Ranges in the area Danger! Observe warning notices
Road used as a public path
Extent of available
information
Byway open to all traffic
Ferry P
PUBLIC RIGHTS OF WAY
(Not applicable to Scotland)
Ferry V
Ferry (vehicle)
Road tunnel
Gradient: 1 in 5 and steeper 1 in 7 to 1 in 5
Bridge
Public rights of way indicated by these symbols have been
derived from Definitive Maps as amended by later enactments
or instruments held by Ordnance Survey on 1st February 1986
and are shown subject to the limitations imposed by the scale
of mapping. Later information may be obtained from the
appropriate County or London Borough Council.
The representation on this map of any other road, track or
path is no evidence of the existence of a right of way.
CHAPTER 2
32.1.2-6
Roads and Paths
18. There are some signs and symbols that will be more important to you when
you are planning an expedition on foot - they will be roads, paths and tracks. Note
the different colours representing different types of road.
Conventional signs
Uncontrolled copy not subject to amendment
Revision 1.00
Heights are to the nearest
metre above mean sea level
Heights shown close to a triangulation pillar refer to the station height at ground level and not
necessarily to the summit.
Contours are at 10 metres
vertical interval
HEIGHTS ROCK FEATURES
+144
50
outcrop 6
5
0
scree
cliff
5
0
0
MAP LANGUAGE
32.1.2-7
Spot Heights
19. Spot heights appear on maps as an added guide and are used to back up
triangulation points. They are represented by a dot with the height next to it (to the
nearest metre).
Contour Lines
20. A contour line is a reddish brown line drawn on the map joining all points of
equal height above mean sea level (MSL). Mean sea level is a fixed height
approximately half way between high and low tides calculated at Newlyn in Cornwall
over many years. This MSL gives a common baseline so that anywhere in the UK
can be measured to give an accurate height. By joining all the points at the same
height you can achieve a picture and shape of the land. These contour lines will
wander all over the map and eventually rejoin at the starting point to show an area
of equal height. There is an exception to this rule and that is where a contour line
meets a cliff face. If you look at a contour line and cannot find the height try following
it round until you come across the figure. These heights are shown in small breaks
in the contour line itself and every fifth line is shown slightly thicker to make them
easier to read. These contour lines are situated at 10 metre intervals on the M726
Series and the rise or fall between contours is called the vertical interval (VI).
Railways and Waterways
21. Railway conventional signs are used to indicate either double or single track.
Special features include tunnels, cuttings, sidings and embankments. Stations that
are open to the public are shown in red, whereas a station that is closed is shown in
white. Bridges, viaducts and tunnels especially those connected with roads, railways
and waterways are shown as solid objects when above ground and as dotted or
broken lines when below ground.
Contour lines
Vertical Interval
Conventional signs
Uncontrolled copy not subject to amendment
Revision 1.00
RAILWAYS
WATER FEATURES
Track multiple or single Freight line, siding or tramway
Station
a b
LC
Level crossing
Embankment
Cutting
(a) principal
(b) closed to passengers
Track narrow gauge
Bridges, Footbridge
Tunnel
Viaduct
Marsh or salting
Towpath Lock
Bridge
Footbridge
Slopes
Normal tidal limit
High water mark
Cliff
Canal
Lake
Canal (dry)
Aqueduct
Weir
Ford
Sand
Dunes
Flat rock
Lighthouse (disused)
Lighthouse (in use)
Low water mark
Mud
Shingle
Beacon
CHAPTER 2
32.1.2-8
Tourist Information
22. This information is often very useful. The long distance path information shown
at the bottom simply indicates the route of the path across the sheet.
Conventional signs
Conventional signs
Uncontrolled copy not subject to amendment
Revision 1.00
MAP LANGUAGE
32.1.2-9
Conclusion
23. Remember - conventional signs are appropriate ONLY to the map that you
are using. They may be different on a different version of the same map. These
signs and symbols are easy to learn and the best way to improve your understanding
is to get as much practice using them as possible, then follow it up by groundwork.
There may be one or two signs that you come across that you dont recognise - if in
doubt look in the margin.
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 2
32.1.2-10
Do not mark the paper
in any way - write your
answers on a separate
piece of paper, in the
form of a sentence.
Sample Questions
1. On an M726 series map the letters PC represent:
a. Public convenience
b. Police communications centre
c. Private chapel
d. Picnic site
2. Contour lines are continuous (ie wherever they run they eventually return to
their starting point), with one exception. The exception is:
a. At a cliff edge
b. At the North or South Pole
c. At a river
d. When the land is very flat
3. To help in reading and counting contours to determine heights, some contours
are drawn using thicker lines than the rest. The thicker ones occur:
a. Every 2nd contour
b. Every 3rd contour
c. Every 5th contour
d. Every 10th contour
4. On the M726 series map, spot heights are shown in:
a. Kilometres
b. Metres
c. Feet
d. Yards
Uncontrolled copy not subject to amendment
Revision 1.00
50,000
SCALES
32.1.3-1
CHAPTER 3
Why use a scale?
Different ways to
express a scale
Understanding scale
SCALES
Introduction
1. If your map is to cover a reasonable area then everything on the map has to
be reduced considerably from its real size. The choice of scale would be determined
by the user or the task required.
How do you express scale?
2. There are 3 ways to express scale
a. In words- by saying so many centimetres to the kilometre. For example a
scale of 2cm to 1km means that for every 2cm on the map you would travel
1km on the ground. Measuring the distance from the Squadron Headquarters
to the local Police Headquarters as 12cm on this scale would be equal to 6
km on the ground.
b. As a Representative Fraction (RF)- in this method the scale is expressed
in the form of a fraction, for example
1
Using this method you are
saying that any distances measured on the map are one-fiftythousandth of
the real distance on the ground.
c. As a ratio: very similar to b. but is written as:
1:50,000 The meaning is also the same as b.
Calculation
3. In the case of RF and ratio the expression of the distance, whether it is in
inches, centimetres or metres, is the measurement on the ground. So a 1:50,000
ratio would be equally valid for
1 inch on the map 50,000 inches on the ground
1 cm on the map 50,000 cm on the ground
1 m on the map 50,000 m on the ground
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 3
32.1.3-2
4. If the scale is expressed in words it may be necessary to convert it into either
a RF or a ratio. For example, to convert a scale of 1 inch to 1 mile, you have to
calculate the number of inches in a mile:
There are 1,760 yards in a mile
There are 5,280 feet in a mile (1760 x 3)
There are 63,360 inches in a mile (5280 x 12)
5. So the scale of 1 inch to 1 mile can be expressed as a ratio of 1:63,360. This
type of calculation is made easier using the metric system, but it will still require
careful thought.
Area
6. When using scales, areas of ground will also be proportionately reduced but
remember that areas contract rapidly on small scale maps. For example if you take
a map that is half the scale of another then the area is reduced by a quarter (not a
half). This is because the area of a rectangular figure is length multiplied by breadth.
If you therefore halved the scale you will quarter the area of the map.
7. From this you can see that a large scale map is very detailed in area. As a
rough guide:
Large scale - city or town maps (defined buildings)
Medium scale - Larger areas (buildings as symbols)
Small scale - atlas (large towns in name only)
Reducing areas
The same area of ground in three different scales
(Half the scale = one quarter of the area)
4 x 4 = 16
4
4
2
2
2 x 2 = 4
1Km square at
1:12,500
1Km square at
1:25,000
1Km square
at 1:50,000
Different types of map
use different scales
Uncontrolled copy not subject to amendment
Revision 1.00
SCALES
32.1.3-3
Visualisation
8. If you can get into the habit of checking your scale when you use your map
you will soon become familiar with distances and areas covered by that scale. This
will also make your task of route planning easier to achieve.
Air Photography
9. Photographs from the air can provide an almost instant representation of
what is on the ground. Air photographs, like maps, can become out of date very
quickly. The examples below show the differences between maps and photographs
(both black and white and colour). By using a special lens you can obtain a 3-D
picture of the ground which will show relief. The scale of the photograph is fairly
small and therefore to give adequate detail for use on the ground a very large
photograph would be needed. Which would you prefer to use, a photograph or a
map?
Fig 3-1 Blackpool Airport
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 3
32.1.3-4
Fig 3-2 Telford in Shropshire
Uncontrolled copy not subject to amendment
Revision 1.00
SCALES
32.1.3-5
Do not mark the paper
in any way - write your
answers on a separate
piece of paper, in the
form of a sentence.
Sample Questions
1. If you measured the distance between two places on a 1:50,000 map and it
came to 26 centimetres, what would be the real ditance over the ground in
Kilometres?
a. 52
b. 26
c. 13
d. 7.5
2. On a 1:50,000 M726 series map, what distance on the ground is represented
by 2cm on the map?
a. 4Km
b. 2Km
c. 1Km
d. 0.5Km
3. On a 1:50,000 M726 series map, what distance on the ground is represented
by one side of a 2cm grid square?
a. 1Km
b. 10Km
c. 0.5Km
d. 5Km
4. For which of the following uses would a map with a scale of 1:1,000,000 be
suitable?
a. Showing street and houses in great detail
b. Motoring in the UK
c. Navigating on foot, as in an expedition
d. Long distance aeronautical navigation
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 3
32.1.3-6
Uncontrolled copy not subject to amendment
Revision 1.00
GRID REFERENCES
32.1.4-1
CHAPTER 4
GRID REFERENCES
1. If you look at a M726 Series map you will notice that it is covered in squares.
These squares make up a grid that covers the whole area of the map. The lines are
better known as grid lines and allow you accurately to locate points on the map.
This system also allows you to route plan using grid references (GR). For ease,
the numbers are printed around the grid and inside at every 10th grid line in both
directions across the map.
2. These grid lines belong to a much bigger system that covers the UK and is
known as the National Grid (there is no connection with the electricity supply!).
Grid Lines
UTM
Kilometres Northings
FALSE ORIGIN OF NATIONAL GRID
Kilometres Eastings
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 4
32.1.4-2
The UKs National Grid is not the only one of its kind. There is a world wide grid
called Universal Transverse Mercator Grid (known as UTM Grid), which is used on
aviation and maritime charts evrywhere else in the world, exception UK and Ireland.
The National Grid
3. Every grid system must have a starting point so that the grid can be built up
from it. From the diagram at the previous paragraph you can see that the UKs
starting point is off Lands End. To cover the UK there is a need for seven 100
kilometre lines of eastings (vertical lines) and thirteen 100 kilometre lines of northings
(horizontal lines) from the starting point. These squares of 100 kilometres (Km) are
further identified by two letters. The reference point for the UK national Grid is 49
North 002 West . The grid is numbered from the South West corner. This is explained
in Vol 2 (Instructors Note).
Grid References (GR)
4. You will understand that a map drawn on the scale to fit a 100km square will
have very little detail at all. A map that will be useful to you has to be based on a
much smaller area. The M726 Series covers an area of about 40km
2
which is less
than a quarter of the 100km
2
area. The M726 Series map has squares of 1km in
size giving an accurate scale map for most types of use. The number printed against
each vertical line indicates the number of kilometres that line is east of the starting
point for the 100km square to which your map belongs. The number printed against
the horizontal grid line indicates the number of kilometres the line is north of the
same starting point. There is on a M726 Series map a British National Grid legend
that tells you where your map is in relation to the 100km square. The need for these
grid lines will now become obvious and can be referred to as eastings and northings
lines.
5. It is fairly easy to locate an object within a 1km square as long as you know
what square it is in. This can be done using Easting and Northing to indicate the
south west (SW) corner of the square you wish to identify. By using the SW corner
of the square, the grid reference is standardised so everyone knows what it means.
GRs point to the South
West corners
Uncontrolled copy not subject to amendment
Revision 1.00
GRID REFERENCES
32.1.4-3
6. As shown by the examples you end up with two sets of figures. If you put
them together they form a 4-figure reference. You always quote the eastings first
followed by the northings. There is a saying that might help you remember this
sequence:
Across the hall (eastings) and up the stairs (northings)
26
15 16 17 18 19
25
24
23
22
37
05 06 07 08 09
36
35
34
33
19
03 04 05 06 07
18
17
16
15
7. This 4-figure reference system is a good method of pinpointing objects on the
ground like a church or a farm but if there are more than one of the same object in
that particular square it may get confusing. To overcome this problem you need to
increase your accuracy. There is a system of 6-figure referencing you can use.
8. In the following examples each 1km square has been subdivided into 10
equal parts (1/10ths). Each of the small squares now represents 100m
2
on the
ground. So to give a 6-figure reference you start in the SW corner and get your 1km
grid number (say 33) as before, then mentally divide the grid into ten parts and
estimate how far into the square the object is (say 4). Once this is done add the
figure to the first (giving 334)- now you have your easting. Repeat the process for
the northing and you will end up with a 6-figure reference number. Judging tenths
across the square (both up and down) may be difficult to begin with but with practice
Fig 4-1 GR 1825 Fig 4-2 GR 0536 Fig 4-3 GR 0417
6 Figure GR
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 4
32.1.4-4
it soon becomes an easy system to use.
53
45
46
47
54 55 05
19
20
21
06 07 28
88
89
90
29 30
Noughts
9. When you are compiling your GR you may find it contains noughts. You must
remember to include them. If the object you seek is on the easting or northing lines
then the third number in your grid reference will be a nought, you must include it. In
this example the GR would be:
080 050
07
06
05
04
03
07 08 09 10
Letters
10. In the diagram at paragraph 2 showing the National Grid, the 100Km squares
are identified by the use of letters. You would not normally refer to these but there
are some cases where you would need to (in the completion of a long trek, crossing
into another 100Km square). To provide clarity and to avoid uncertainty the letters
would also be added to the grid reference, for example:
SO 080 050
Fig 4-7 GR080 050
The full GR
Fig 4-4 GR 545 454 Fig 4-5 GR 058 205 Fig 4-6 GR 299 902
Uncontrolled copy not subject to amendment
Revision 1.00
GRID REFERENCES
Plotting A Grid Reference
11. If you had been tasked to locate an object at a given reference 875 303 on
Sheet 130 on a M726 Series 1:50,000 map, this is how you might go about it:
a. Mentally divide the number into two segments.
b. This gives you 875 and 303.
c. Use the 87 from the first set (easting).
d. Locate that number across the sheet.
e. Use the 30 from the second set (northing).
f. Locate that number up or down the sheet.
g. You will now be able to locate the SW corner of the square where the
object lies - 87 30.
h. Now use third number from the first set (5).
i. Move half way across the easting line.
j. Use the third number of the second set (3).
k. Move up the grid 3 tenths.
l. At this point you will find a trig point at 141m.
12. This may seem a long process but once you have gained some experience
you will no doubt develop your own method and increase your speed.
13. So far you have been estimating the 10 divisions required for a 6 figure
reference. There are more accurate methods of taking this measurement. One such
method is a useful device called a Roamer. This device has tenths marked out in
several different scales along various edges. You can find these scales on most
compasses designed for navigation on foot.
32.1.4-5
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.4-6
CHAPTER 4
Picture of a Roamer.
Uncontrolled copy not subject to amendment
Revision 1.00
Do not mark the paper
in any way - write your
answers on a separate
piece of paper, in the
form of a sentence.
Sample Questions
1. A Roamer would be used in finding:
a. The direction of a track
b. The grid reference point
c. The average gradient
d. A relative bearing
2. When using an M726 1:50,000 map, a 4-figure grid reference will define a 1
Kilometre square on the map. The 4-figure reference refers to a particular corner
of the square: whcih corner?
a. NE
b. SE
c. NW
d. SW
3. Each side of each Grid square on a 1:50,000 map represents on the ground:
a. 1/2 Kilometre
b. 1.5 Kilometre
c. 1 Kilometre
d. 2 Kilometre
4. What is the meaning of the two letters in a Grid Reference using the UK
National Grid e.g. a GR of TL307624?
a. The point is located in one of the Grid squares with sides of 500Km
b. The point is located in one of the Grid squares with sides of 1Km
c. The point is located in one of the Grid squares with sides of 100Km
d. The point is located 30Km East and 62Km North of origins of the grid
32.1.4-7
GRID REFERENCES
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.4-8
CHAPTER 4
Uncontrolled copy not subject to amendment
Revision 1.00
RELIEF
CHAPTER 5
RELIEF
Introduction
1. The word relief means the rise and fall of the ground or, in other words such
features as hills and valleys. This involves both the height and the shape of the
land. As a map is drawn on a flat sheet of paper the representation of height and
shape is difficult. Map makers have various ways of doing this, but whatever method,
it is left to the reader (you!) to interpret the information. This chapter introduces you
to relief on a map.
Height
2. Methods of showing height on a map include:
a. Spot heights and triangulation points, which are used to give an accurate
height above sea level at given points. They give an indication of height but
not shape.
b. Layer tinting, which uses colours that may vary depending on the type of
map you are using. For example, land up to 60 metres may be coloured
green, rising higher ground may be light brown and higher ground still may
be in dark brown. If this system is in use on a map you will find a key legend
for the colours in the margin. Layer tinting gives you some idea of the shape
as well as height and its main advantage is that it gives a quick impression of
the highest and lowest ground. However, because of its general nature it is
best to use it only as a rough guide.
Unit Of Measurement
3. Units of height are important. In particular you must appreciate the difference
between feet and metres, a foot being about the size of your shoe whereas a metre
is a full stride. You can imagine your groups reaction if you were planning to climb
a hill of a 1,000 feet which was going to take two hours, only to find that it was
actually 1,000 metres taking six or seven hours to climb. Hence it is vital to know
the units of height from the planning stage right through to the execution of an
exercise.
What is relief?
Methods of showing
height
CHECK the units of
height
32.1.5-1
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 5
32.1.5-2
Shape
4. Methods of showing shape include:
a. Hachures. These are short tadpole-shaped strokes, the thicker end of the
stroke being in the direction of the higher ground. When depicting steep
ground they are drawn thickly and close together. On areas where the ground
is a gentle slope, the hachures are drawn thinly and wider apart. This method
gives no definite height indication and is seldom used except to show cuttings,
embankments and steep slopes.
b. Hill Shading. Hill shading is similar to hachures, but using an oblique stroke
to achieve a depth of shading. This means that the darkest shading is the
steepest ground. Another form of shading is based on a convention that light
is shed from the NW corner and the hills are shaded accordingly. This method
does not in itself give any indication of height.
Contour Lines
5. Contour lines on a map join all the points of the same height together and,
with a little practice you can get from them a very good idea of the shape of the
ground. So much so, they are the standard way in which height is depicted. There
are some points to bear in mind before you start interpreting information from contour
lines:
a. Between any two contour lines there must be a slope either up or down.
b. Contour lines are continuous and only stop abruptly at a cliff edge.
c. Heights on contour lines are printed so that when you read them the right
way up, you are facing uphill.
Contour lines
Showing steep ground
Fig 5-1 Hachures
Uncontrolled copy not subject to amendment
Revision 1.00
RELIEF
Contour Plans
6. Contour lines represent an area on the ground and can be thought of as a
plan of that ground. If you take a map and look at the contour lines you will see
something like the plan view shown below. From this representation you can build
up a picture in your minds eye as to what it will look like on the ground (side view).
The perspective is the combination of plan and side views and gives both the shape
and height of the object.
Slopes
Steepness and direction
7. If two contour lines are far apart it would suggest there is a greater distance
to travel from one to the other to gain the height. This is better described as a gentle
slope. If you see two contour lines very close together you would expect to see a
very steep slope. The next few figures demonstrate these points well and with
practice you too will be able to see when a climb will be hard (steep) or easy
(gentle). It is not always easy to tell in the classroom whether a set of contours
represents a steep upward or a steep downward slope. Remembering that contour
Steep or gentle slopes?
Contour markings face
uphill
Fig 5-2 Visualising the
shape of the land
32.1.5-3
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 5
32.1.5-4
values are always printed facing uphill this should give you a good guide in telling
which way the slope is going. Other clues may be available to you, like rivers or
lakes as these tend to be at the bottom of a slope.
Fig 5-3 Photograph from
GR 289 824
Facing West
Uncontrolled copy not subject to amendment
Revision 1.00
RELIEF
Fig 5-4 Photograph from
GR 402 083
Facing North
32.1.5-5
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 5
32.1.5-6
Convex/Concave
8. As well as being gradual or steep, slopes may be convex or concave. The
diagram shows in line CXYD that the slope is convex (YD) because the contours
are closer together at the bottom. If the contours are further apart at the bottom as
in (CX) the slope is concave. It follows that if the contour lines are more evenly
spaced, then the slope will be relatively uniform or straight.
Lie of the land
9. Where contours meander and are varying distances apart, but never very
close, the ground is undulating and relatively flat. You can only gain a little knowledge
of the ground from the sparse detail, but the land will fall gentle from the higher
contour to the lower one.
Fig 5-5 Convex and
Concave slopes
Uncontrolled copy not subject to amendment
Revision 1.00
RELIEF
Ridges Saddles and Cols
A ridge is a long narrow stretch of elevated ground; it is also known as a saddle.
Where a ridge has a peak at each end, the lower part of the ridge between the
summits is called a col.
Fig 5-6 Photograph from
GR 878 365
Facing North
32.1.5-7
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 5
32.1.5-8
Fig 5-7 Ridge and Col
Fig 5-8 Photograph from
GR 176 567
Facing West
Uncontrolled copy not subject to amendment
Revision 1.00
RELIEF
Spurs And Re-entrants
11. A spur is a piece of high ground jutting from a range of hills into lower ground.
A re-entrant is a narrow valley closed at one end, separating two spurs. They are
very similar on the map because the contours for both will have a hairpin shape.
You will need to study the contour heights and decide whether the closed part of the
hairpin points to the high or low ground. If the closed part points in the direction of
the lower ground it is a spur - shown in the diagram. If the closed part points towards
the higher ground it is a re-entrant.
Difference between
Spurs and Re-entrants
Fig 5-9 Photograph from
GR 973 589
Facing North
32.1.5-9
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.5-10
CHAPTER 5
Escarpment and Knoll
An escarpment is a landform with sides sloping in opposite directions consisting of
a steep scarp slope and a more gentle dip or back slope. A knoll is a small isolated
hill.
Fig 5-10 Spurs and
Re-entrants
Fig 5-12 An Escarpment
Fig 5-11 Escarpment
Uncontrolled copy not subject to amendment
Revision 1.00
RELIEF
For expamples of Knolls and peaks at different grid references see over.
Conclusion
If you use the information that is provided by a contour map the lie of the land will
become easy to interpret with experience and practice. Once gained, this experience
will allow you to build a mental picture of the ground when reading the map in the
planning stage.
32.1.5-11
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.5-12
CHAPTER 5
Uncontrolled copy not subject to amendment
Revision 1.00
RELIEF
F
i
g

5
-
1
3

B
r
e
n
t

K
n
o
l
l

f
r
o
m

G
R

3
8
9

5
5
2
F
i
g

5
-
1
5

B
r
e
n
t

K
n
o
l
l

f
r
o
m

G
R

3
4
9

5
0
9
F
i
g

5
-
1
4

C
r
o
o
k

P
e
a
k

f
r
o
m

G
R

3
7
8

5
5
5
F
i
g

5
-
1
6

C
r
o
o
k

P
e
a
k

f
r
o
m

G
R

3
7
1

5
2
5
32.1.5-13
Uncontrolled copy not subject to amendment
Revision 1.00
Do not mark the paper
in any way - write your
answers on a separate
piece of paper, in the
form of a sentence.
Sample Questions
1. In map reading, what does the word relief mean?
a. Hill shading
b. Layer tinting
c. The rise and fall of the land
d. Hachuring
2. What shape would the contours be for a spur?
a. Round
b. Elliptical
c. Hairpin
d. Straight
3. If you were to rotate the map so that the figures on the contour lines were the
right way up, which way would you be looking?
a. Down the slope depicted by the contours
b. Up the slope depicted by the contours
c. Grid North
d. True North
4. What must there be between any two adjacent contour lines (on a map)
which have different values?
a. Flat land
b. A slope
c. A ridge
d. A spur
CHAPTER 5
32.1.5-14
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.6-1
GRADIENTS
CHAPTER 6
GRADIENTS AND INTERVISIBILITY
1. In this chapter you will learn more about slopes. You will see how the steepness
of a slope is expressed and how to work out what you should be able to see from a
given point.
Gradients
2. The angle or degree of a slope is called a gradient and is expressed as a
ratio. Imagine a slope with a gradient of 1:5. This would mean that for every 5 units
along the ground (horizontally) the slope will rise or fall by 1 unit. If this ratio is small
the slope will be very steep and if the ratio is large the slope will be gentle. Very
steep roads in the UK are specially marked on maps so that you may avoid them if
you wish.
Measurement Of A Gradient From A Map
3. To work out a gradient from a map you need to know both the vertical interval
(VI) and the horizontal equivalent (HE). Given 2 points A and B, it is possible to
calculate the VI by measuring the distance between the contour lines. In the example
this measurement would be 40 metres. To obtain the HE use the maps scale and
measure the distance between the 2 points. In the example the HE is measured out
to be 2000 metres. IT IS IMPORTANT THAT YOU USE THE SAME UNITS OF
MEASUREMENT IN BOTH THE HE AND THE VI. You now have two figures and
you must reduce these to a ratio in which the VI is 1.
Fig 6-1 Slopes - gentle or
steep
Gradients expressed as
a ratio
VI and HE
AC = VERTICAL INTERVAL (VI)
CB and CD = HORIZONTAL EQUIVALENT (HE)
Uncontrolled copy not subject to amendment
Revision 1.00
VI= 40
HE= 2000
4. The ratio is 40:2000 which (if 2000 is divided by 40) gives1: 50. The ratio of
1:50 for this slope means that for every 1 unit you ascend you have moved forward
50 units. If you are looking at a map and your planned route takes you across some
steep ground (where the contours are so close together that short measurements
are difficult), measure the HE over several contours.
Visualising Gradients
5. The eye tends to exaggerate slopes and so in order to visualise an area of
ground accurately from a map a great deal of practice is required. To find gradients
you must measure the distances between contours, which may be small and difficult
to measure accurately on a M726 Series 1:50,000 map. However, it is quite easy to
construct a table that will assist you in visualising gradients.
6. Begin with contours that are as close as 1mm to each other. From the scale
you know that 1mm on the map equals 50,000mm on the ground, which is 5000cm
or 50 metres. Thus you have an HE of 50m. On the M726 map the VI between
contours is 10m. A VI of 10 with an HE of 50 gives a gradient of 10:50 or 1:5. Similar
calculations for contour lines that are 2mm apart give a gradient of 10:100 or 1:10.
For a 3mm spacing the gradient is 10:150 or 1:15, and so on. In this way you can
build up your own copy of the table on the next page. The table also shows a
column for expressing gradients as a percentage; you may wish to complete this
column if you are familiar with percentages - your instructor will help if you need it.
Fig 6-2 Calculating a
gradient
CHAPTER 6
32.1.6-2
SCALE - KILOMETRES
Uncontrolled copy not subject to amendment
Revision 1.00
Do not mark the table below but use it as a guide. You may like to draw it or use a
photocopy.
GRADIENTS
DISTANCE BETWEEN GRADIENT APPROX
ADJACENT CONTOURS AS % GRADIENT
(IN MILLIMETRES)
1 20 1:5
2 10 1:10
3 6.66 1:15
4 5 1:20
5 4 1:25
6 3.33 1:30
7 2.85 1:35
8 2.5 1:40
9 2.22 1:45
10 (1cm) 2 1:50
11 1.8 1:55
12 1.66 1:60
13 1.54 1:65
14 1.43 1:70
15 1.33 1:75
16 1.25 1:80
17 1.18 1:85
18 1.11 1:90
19 1.05 1:95
GRADIENTS
32.1.6-3
Uncontrolled copy not subject to amendment
Revision 1.00
Intervisibility
7. When you are map reading it may be necessary to know whether you can
pick out a feature or point to help in the next stage of your route. Be very careful
because as these examples show interpreting the lie of the ground can be tricky.
CHAPTER 6
32.1.6-4
What is Intervisibility?
Fig 6-3 Concave slope Fig 6-4 Convex slope
Fig 6-5 Visible ground
CONCAVE SLOPE
B can be seen from A
CONVEX SLOPE
B cannot be seen from A
No Intervening high ground
(B can be seen from A)
Uncontrolled copy not subject to amendment
Revision 1.00
GRADIENTS
8. If the ground between you and your goal is not clear you may have to draw a
section. Your instructor will help you if have any problems understanding how it is
done.
9. Cover the diagrams with tracing paper and using a pencil, lightly mark the
shape of the land in the following examples.
When to draw a section
32.1.6-5
Uncontrolled copy not subject to amendment
Revision 1.00
10. Intervisibility problems cannot always be solved accurately from a map.
Buildings and trees are not always shown on maps, especially if they have been
added since the map was drawn. If visibility is critical for what you are doing then a
reconnaissance visit must be made.
11. Now that you have had some practice drawing sections, try this example.
Remember to use tracing paper and pencil ONLY.
Fig 6-6 Beware of
unseen ground
CHAPTER 6
32.1.6-6
Uncontrolled copy not subject to amendment
Revision 1.00
Do not mark the paper
in any way - write your
answers on a separate
piece of paper, in the
form of a sentence.
Sample Questions
1. If the Vertical Interval between two places is 90 metres and the Horizontal
Equivalent is 2 kilometres, what is the gradient (to the nearest whole figure)?
a. 1:11
b. 1:22
c. 1:33
d. 1:44
2. Which of these gradients is the steepest?
a. 1:7
b. 1:11
c. 1:14
d. 1:17
3. If, by studying a map, you cannot be sure whether one place can be seen
from another, what can you do to decide?
a. Draw a cross-section of the land between them
b. Calculate the gradient between them
c. Calculate the mean contour line
d. Calculate the height of the land by reference to the spot heights in the
area
32.1.6-7
GRADIENTS
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 6
32.1.6-8
G
E
N
E
R
A
L

E
X
E
R
C
I
S
E
G
i
v
e

t
h
e

6

f
i
g
u
r
e

G
r
i
d

R
e
f
e
r
e
n
c
e

o
f

t
h
e

p
o
i
n
t
s

o
f

d
e
t
a
i
l

i
n
d
i
c
a
t
e
d

b
y

t
h
e

a
r
r
o
w
s
Uncontrolled copy not subject to amendment
Revision 1.00
GRADIENTS
G
E
N
E
R
A
L

E
X
E
R
C
I
S
E

2
I
d
e
n
t
i
f
y

t
h
e

c
o
n
v
e
n
t
i
o
n
a
l

s
i
g
n
s

b
y

t
h
e

n
u
m
b
e
r
e
d

a
r
r
o
w
s

w
i
t
h
o
u
t

r
e
f
e
r
e
n
c
e

t
o

a

l
e
g
e
n
d
32.1.6-9
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 6
32.1.6-10
G
E
N
E
R
A
L

E
X
E
R
C
I
S
E

3
I
d
e
n
t
i
f
y

t
h
e

r
e
l
i
e
f

f
e
a
t
u
r
e
s

i
n
d
i
c
a
t
e
d

b
e
l
o
w
1
.

N
a
m
e

t
h
e

r
e
l
i
e
f

f
e
a
t
u
r
e
s
n
u
m
b
e
r
e
d

1
-
5
2
.

W
h
a
t

a
r
e

t
h
e

t
y
p
e
s

o
f

s
l
o
p
e
s
u
n
d
e
r

t
h
e

l
i
n
e
s

n
u
m
b
e
r
e
d

6
a
n
d

7
?
3
.

W
h
a
t

i
s

t
h
e

a
p
p
r
o
x
i
m
a
t
e
h
e
i
g
h
t
,

a
b
o
v
e

s
e
a

l
e
v
e
l

o
f
L
o
n
g

L
o
c
h
?
4
.

W
h
a
t

i
s

t
h
e

d
i
f
f
e
r
e
n
c
e

i
n
h
e
i
g
h
t

b
e
t
w
e
e
n

t
h
e

K
i
n
l
o
c
h
M
o
u
n
t
a
i
n

R
e
s
c
u
e

P
o
s
t

a
n
d
H
a
l
l
i
v
a
l

(
3
9
5

9
6
3
)
?
5
.
W
h
a
t

i
s

t
h
e

n
a
m
e

o
f

t
h
e
f
e
a
t
u
r
e

n
u
m
b
e
r
e
d

8
,

a
n
d

w
h
a
t
i
s

i
t
s

h
i
g
h
e
s
t

p
o
i
n
t
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 1
INSTRUCTORS GUIDE
32.1.1a NOTES
INSTRUCTORS GUIDE
Page 32.1.1-4 Para 12
MAP READING
WHAT IS A MAP?
1. Once you have selected your map - HOW do you use it?
It is necessary that the cadets know the following points in connection with the subject.
Planning is a very important part of any activity and time should be spent on getting to know the
area you intend to go. The sort of things to look out for are those features which stand out on the
map and would be easily recognisable on the ground. This is particularly useful if you or your party
run into problems - remember your reaction will be quicker if you familiar with the map. Once you
are happy with your map and feel confident to use it you need to go out and gain some experience
of comparing the map to the ground area. This may be achieved in towns, cities or local country
side. Any map may be used even a street map as long as it gives the cadets practice in moving
from one point to another.
2. If you look at any atlas of the world, you will get a good idea of how continental landmasses
lie compared to oceans. When the surface of the earth is shown on a flat piece of paper some
distortion takes place. You can spot errors of distortion if you look closely. For example Greenland
is shown to be larger than India but in fact India is approximately four times the size of Greenland.
This happens because the surface of the earth is stretched at the poles and squeezed at the
equator to make it lie flat.
Maps tend to be accurate in shape and position (bearing) - they are inaccurate as far as distance
and area are concerned.
To allow more detail to be shown the world map can be broken down into many single sheet maps.
You might think of it as using a microscope with the world under the lens. The more you zoom in
the clearer the picture becomes and the more accurate the image you get.
3. To make map reading more enjoyable and to make cadets think, you may like to try some
of the following ideas.
a. Blindfold a cadet and then pace out a set distance in a straight line. Make a note of how
much drift there is and in what direction it was.
b. Have one cadet blindfolded and have another direct the first through a small obstacle
course (using paces and direction only).
c. Have the cadets draw a map of the town/village or city centre (from memory) then compare
the results to an actual map.
d. Try comparing old maps to new ones to see what changes have taken place in your
area.
e. Mark out a route on an aerial photograph and have the cadets follow it.
f. Use different types of ground to find out different pace numbers and times i.e. 100m on -
paths, road, tracks, bracken, heather, sand, uphill and downhill.
4. Map reading can be fun but it also has a serious side. If you decide to go out for a walk
locally it is possible to get lost. A map can be a good friend to you when you are out walking - dont
leave home without one!
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.1b NOTES
CHAPTER 1
Page 32.1.1-5 Para 16 There are many types of maps in general use. Different types of map depict different types
of information. Although maps tend to suit a specific user, different types of map can sometimes be
used by different groups. For map reading in the Corps the important factor is scale. The many
types of map available on the market reflect the wide range of activities for which maps are needed.
Motoring atlas of the UK 1 inch to 3 mile scale
Cycle tours 1:50,000 or 1.25 inches to 1 mile
Explorer maps 4 cm to 1 Km or 2.5 inches to 1 mile
Pathfinders maps 4 cm to 1 Km or 2.5 inches to 1 mile
Coast to Coast maps
Travelmaster map 1 inch to 4 miles
Waterway guides
Outdoor Leisure maps 4 cm to 1 Km or 2.5 inches to 1 mile
National Trail guide 1:25,000
Historical maps and guides 1 cm to 25 cm or 25 inches to 1 mile
World Atlas
Local authority maps
Air maps
Agricultural maps
Marine maps
Political maps
There are now available CD-ROMS that contain information that you can interrogate, zoom
in or walk through in detail.
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 2
INSTRUCTORS GUIDE
32.1.2a NOTES
INSTRUCTORS GUIDE
MAP LANGUAGE
ROADS
Roads in the UK are categorised into classes. All roads except motorways are classed
according to the width, surface and ease of driving (no really sharp bends). There are 3 main
classes and they are:
a. Trunk Roads - Motorways and A(T) Roads. These are maintained by Central Government
b. Classified Roads - A and B Roads. Maintained by the County Council through which they
run.
c. Unclassified Roads - Footpath, bridleways and urban roads. These are maintained by
the local District Council concerned.
TRUNK ROADS
A trunk road has been so classed by the Trunk Roads Act 1936 or 1946, or has been made
a trunk road (either by upgrading or construction) by order of the Government. Trunk Roads form
part of the road system for through traffic. The roads are numbered and carry either a prefix, a
suffix or both. For example:
M25 where the M is for Motorway
A1 where A is for All purpose
A1(M) where an A road has been upgraded or constructed to motorway standard.
MOTORWAYS
Motorways are the only type of road that is constructed to a specific standard and has
restrictions placed on their use. Motorways are built to at least dual carriageway standard, with
hard shoulders. Motorways have limited joining points and NO intersections.
A ROADS
A roads are all purpose and prefixed with the letter A. They are deemed as important to the
road system, whether they are feeders to the trunk roads or as part of the urban infrastructure.
B ROADS
B roads are classed to be not as important as A roads but have a value to the communities
through which they pass.
UNCLASSIFIED ROADS
Unclassified roads carry no numbers or letters and serve the area in which they are built.
THE HIGHWAY CODE
The Highway Code contains a wealth of information regarding road types, description and
uses. Also contained within the Highway Code is rules for safety of pedestrians. This would prove
useful information that can be studied and observed by those planning or executing expeditions on
foot.
Page 32.1.2-6 Para 18
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 3
32.1.3a NOTES
CHAPTER 3
INSTRUCTORS GUIDE
SCALES
Map Scales
It may be hard for the cadets to understand that as the Representative Fraction (RF)
increases the smaller the scale becomes. The following table will allow you to ask the cadets their
ideas on the RFs of the following:
RF Cm to Km Use
Large scale 1:1250 80 Town plans
1: 25,000 4 Tactical/leisure
1: 50,000 2 Tactical/leisure
Medium scale 1: 250,000 0.4 Strategical/tactical
Small 1: 625,000 0.151 Planning
A good exercise for cross referencing map symbols to the air photograph is select a few
points on the map and have the cadets pick them out from the map. It is a good comparison
exercise coupled with improving map symbol skills.
Page 32.1.3-1 Para 2
Page 32.1.3-3 Para 9
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 4
INSTRUCTORS GUIDE
32.1.4a NOTES
INSTRUCTORS GUIDE
GRID REFERENCES
Making a Roamer
A Roamer is an aid to measuring the tenths on a map. Although these scales are included
on most compasses, a roamer is a very easy guide to make. By using a postcard you can achieve
quite an accurate measuring tool for grid reference work. You could give it two different scales if so
desired. Place the edge of the postcard onto a 1:50,000 scaled map. Locate the corner of the
postcard near the bottom centre of the map by the scaling bars. The top one of these is the
kilometres scale and the first part of that scale is marked off in tenths. Carefully align the postcard
along this edge and mark off the scale. Rotate the postcard through 90 degrees and repeat. Once
you have finished the 1:50,000 scale you could possibly use another scale map for the other
corners.
You should end up with something like this:
Place the corner of the postcard on the map feature that you want to record as a GR - make
sure the edges of the postcard are parallel to the grid lines. Count the number of tenths, both
horizontally (eastings) and vertically (northings) to the lower numbered grid line - when added to
the 4 figure GR, you now have the GR in 6 figures.
Page 32.1.4-5 Para 11
Uncontrolled copy not subject to amendment
Revision 1.00
CHAPTER 5
32.1.5a NOTES
CHAPTER 5
INSTRUCTORS GUIDE
RELIEF
Drawing a section
To encourage the understanding of contour lines there are ways to build up a picture. In the diagram
a line AB is drawn across the contours (You may use either plain or squared paper). Every time a
contour line cuts AB draw a dotted line down to line AB (this is at mean sea level). Draw horizontal
lines to match the contour line height above line AB. Once this is completed you can drawn the
section by joining the dots.
Page 32.1.5-12 Para 11
Uncontrolled copy not subject to amendment
Revision 1.00
ANSWER SHEET
Self Assessment Questions - Answer Sheet
Chapter 1 Page 32.1.1-8
1. a
2. c
3. a
4. d
Chapter 2 Page 32.1.2-10
1. a
2. a
3. c
4. b
Chapter 3 Page 32.1.3-5
1. a
2. c
3. a
3. d
32.1.5b NOTES
Uncontrolled copy not subject to amendment
Revision 1.00
32.1.5c NOTES
ANSWER SHEET CONT...
Self Assessment Questions - Answer Sheet cont...
Chapter 4 Page 32.1.4-7
1. b
2. d
3. c
4. c
Chapter 5 Page 32.1.5-14
1. c
2. c
3. b
4. b
Chapter 6 Page 32.1.6-7
1. b
2. a
3. a
Uncontrolled copy not subject to amendment
Revision 1.00

You might also like