6 No.32395 Government Gazette, 15 July 2009

Download as pdf or txt
Download as pdf or txt
You are on page 1of 17

6 No.

32395 GOVERNMENT GAZETTE, 15 JULY 2009


"SANS 10228" means the Standard Specification for the identification and
classification of dangerous goods for transport, SANS 10228, published by
the South African Bureau of Standards;
"SANS 10254" means the Standard Specification for the installation,
maintenance, replacement and repair of fixed electric storage water heating
systems. S,t\NS 10254. published by the South African Bureau of Standards;
SANS/ISO 17020" means the Standard Specification for general criteria for
the operation of various types of bodies performing inspection, SANS 17020,
published by the South African Bureau of Standards:
"steam generator" means any apparatus to convert water continuously into
steam at a pressure higher than that due to the atmosphere and where the
heat ;s derived from a source other than steam, and includes any super
heater or economiser which is an integral part of a steam generator or is
separately fired there from, fired steam and hot-water boilers, waste-heat
boilers, waste-incineration boilers, and electrode or immersion-type
electrically heated boilers;
"the Act" means the Occupational Health and Safety Act, 1993 (Act No. 85 of
1993);
"transportable gas container" means any refillable vessel for the storage
and conveyance of liquefied, dissolved or compressed gases, of water
capacity from 0,5 litres to 3000 litres;
"unique mark" means the mark and accreditation reference number of the
approved inspection authority_
7 STAATSKOERANT, 15JULIE2009 NO.32395
Scope of application
2. (1) These Regulations shall apply to the design, manufacture,
operation, repair, modification, maintenance, inspection and testing of
pressureequipmentwithadesignpressureequaltoorgreaterthan 50kPa, in
terms of the relevant health and safety standard incorporated into these
Regulationsundersection44oftheAct.
(2) Regulations 3, 4, 5, 9(1), 9(2) and 9(3) shall not apply to pressure
equipment in use oron order prior to the publication ofthese Regulations,
which equipment shall be designed and constructed according to the
requirementsapplicableatthetimeoforder.
(3) The following pressure equipment shall be excluded from these
Regulations:
(a) Piping forthe supply, distribution and discharge ofwater below
its boiling point at atmospheric pressure and associated
pressure equipment and headraces such as penstocks,
pressuretunnels, pressure shafts for hydro-electric installations
andtheirrelated specificpressureaccessories;
(b) aerosoldispensers;
(c) pressure equipmentintendedforthefunctioning ofroad and rail
vehicles, excludingafuelgassystem;
(d) pressureequipmentcomprising casings ormachinerywherethe
dimensioning, choice of material and manufacturing rules are
based primarily on requirements for sufficient strength, rigidity
and stability to meetthe static and dynamicoperational effects
orotheroperationalcharacteristicsandforwhich pressure is not
a significant design factor, and such pressure equipment may
include-
(i) engines, including turbines and internal combustion
engines;
(ii) reciprocating steam engines, gas turbines, steam
turbines, turbo-generators, compressor engines, pumps
andactuatingdevices;
(e) open metal-making potsandblastfurnaces
(f) housing for electrical machinery such as switchgear, control
gear, transformersand rotatingmachines;
(g) tyres and flexible pressurised casings used for recreational
purposes;
8 NO.32395 GOVERNMENTGAZErrE, 15JULY2009
(h) fixed electrical hot-water storage container of water capacity
from 15 litres to 450 litres operating at amaximum pressure of
600kPa manufacturedtothe requirements ofSANS 151, which
shall be installed in accordance with the requirements of SANS
10254.
Generalrequirements
3. (1) Anyperson who manufactures, imports, sells, offers orsupplies
any pressure equipment described in these Regulations for use in the
RepublicshallensurethatsuchequipmentcomplieswiththeseRegulations.
(2) Any person who erects or installs any pressure equipment for use in
the Republicshallensure, asfarasisreasonablypracticable,thatitiserected
or installed in a safe manner and without risk to health and safety when
properlyused.
(3) Allpressureequipmentforuseinthe Republicshall becategorized and
submitted to the applicable conformance assessments of SANS 347 in
addition to the requirements of the relevant health and safety standard
incorporated intothese Regulationsundersection44oftheAct.
Dutiesofmanufacturers
4. (1) The manufacturer shall have an obligation to ensure that all
equipment designed and manufactured for use in the Republic shall be
conformityassessedand subjectedtothe requirementssetoutin SANS 347.
(2) Subject to the requirements set out in the relevant health and safety
standard incorporated intothese Regulations undersection 44 oftheAct, the
manufacturer shall ensure that the pressure equipment as manufactured,
modified, inspected, tested or repaired is safe and without risks to health
when properlyused.
(3) Subject to the requirements of this regulation a manufacturer shall
issue acertificate ofmanufacturefor all pressure equipmentsupplied, with a
verificationsignaturebyanapprovedinspectionauthoritywhensorequired.
(4) Subject to the requirements of this regulation a manufacturer shall
comply with any other duty assigned to the manufacturer in these
Regulations.
(5) A manufacturerwho determinesthatpressure equipmentin use has a
latentdefectshall advise the chiefinspectorin writing forthwiththereofand of
measuresbeingtakentocorrectthedefect.
Dutiesofimportersandsuppliers
5. (1) Importers and suppliers shall ensure that pressure equipment
sold complieswiththerequirementsofthese Regulations.
9
STAATSKOERANT, 15JULIE2009
No.32395
(2) The importershall assume the liability ofthe manufacturer in terms of
theseRegulations.
(3) Any pressure equipment that requires a permit to be issued by an
organisation approved bythe chiefinspectorshall ensurethatsuch approval
isobtained bythe importerormanufacturerbeforethepressureequipmentis
placed in the market: Provided that such equipment shall comply with the
relevanthealthandsafetystandard incorporatedintotheseRegulations under
section44 oftheAct. .
Duties of users
6. (1) The usershall ensure thatthe pressure equipment is operated
and maintainedwithin itsdesignandoperating parameters.
(2) The user shall, subject to the relevant health and safety standard
incorporatedintothese Regulationsundersection44 oftheAct-
(a) provide the manufacturer, repairer or modifier with
comprehensive information of the operating or intended
operating conditions of the pressure equipment, including the
characteristics of the fluid and operating parameters of other
connected pressureequipment,wherereasonablypracticable;
(b) ensure pressure equipment has a certificate, issued by the
manufacturer, including a verification signature by an approved
inspection authority when required, which certi'fies that the
pressure equipment has been designed and manufactured in
accordance with the relevant health and safety standard
incorporated intotheseRegulationsundersection44oftheAct;
(c) ensure pressure equipment has a certificate issued by the
repairer or modifier, including a verification signature by an
approved inspection authoritywhen required, which certifiesthat
the pressure equipment has been modified or repaired in
accordance with the relevant health and safety standard
incorporatedintothese Regulationsundersection44oftheAct;
(d) ensure that pressure equipment has a certificate issued by an
approved inspection authority before commissioning, where
applicable; and
(e) ensure that a gas system has a valid certificate issued by an
authorisedperson.
10 No.32395 GOVERNMENTGAZETTE, 15JULY2009
Approval and duties of approved inspection authority
7. (1) Only an organisation holding an approval certificate from the
chief inspector shall perform the duties of an approved inspection authority
withinthescopeofaccreditation.
(2) An application for approval in terms ofsubregulation (1) shall include
the applicant's proof of accreditation prescribed by paragraph (a) or (b) of
subregulation(3), includingfullcontactdetailsandaddress.
(3) Thechiefinspector'sapproval-
(a) ofinspectionbodiesoperating in the Republicshallbesubjectto
the submission of an accreditation certificate issued by the
accreditation authority in accordance with the requirements of
SANSIISO 17020 and SANS 10227: Provided that the chief
inspector may set additional requirements before granting
approval; or
(b) offoreign inspectionbodiesshallbesubjecttothesubmissionof
an accreditationcertificate issued byan InternationalLaboratory
Accreditation Cooperation (ILAC) or an International
Accreditation Forum (IAF). Mutual Recognition Arrangement
signatory in accordance with the requirements of ISOIIEC
17020: Providedthat-
(i) the foreign inspection bodyshall ensure compliance with
all the duties assigned to an approved domestic
inspection authority in terms of these Regulations and
within their scope of accreditation together with the
applicablehealthand safetystandards; and
(ii) the chief inspector may set additional requirements
beforegrantingapproval.
(4) Imported pressure equipment stamped by an ASME authorised
manufacturerin compliancewith the full ASME Code ofConstruction shall be
deemedto meettherequirementsoftheseRegulations.
(5) Intheeventofadisputeofatechnical orsafetyissue, which could not
be reasonably resolved between an approved inspection authority and any
interested party, including the user, modifier, repairer or manufacturer, an
interested party may refer the case to the chief inspector in writing for
arbitration, settingoutthefulldetailsofthedispute.
(6) Upon receiving such a dispute in terms ofsubregulation (5), the chief
inspector may appoint an arbitrator mutually agreed upon between the
parties.
(7) Acasereferredtothechiefinspectorin termsofsubregulation (5)shall
be investigatedand arbitratedwithin amaximumof90days.
STAATSKOERANT, 15JULIE2009 NO.32395 11
(8) An approved inspection authority shall ensure compliance with all the
duties assigned to an approved inspection authority in these Regulations
within itsscopeofaccreditationandtherelevanthealth and safetystandard.
Registration of a steam generator
8. (1) No user may use a steam generator unless such user IS In
possession ofacertificate ofregistration issued in terms ofsubregulation (3)
forthatsteamgenerator.
(2) Application for registration to use a steam generator shall be made
prior to use to the provincial director in the form ofAnnexure 2. including
copies of a certificate from the manufacturer and from the approved
inspectionauthorityafterinstallation priortocommisSioning: Provided thatthis
subregulation shall not apply in respect of the re-erection of a steam
generatoronthesamepremises.
(3) On receipt ofan application for registration in terms of subregulation
(1). the provincial directorshall forward that application to an inspector who
may issue a certificate ofregistration in the form ofPart C ofAnnexure 2in
respect of that steam generator, subject to the conditions that may be
speci'fied on thecertificate.
(4) Anyuserofasteamgeneratorforwhich acertificateofregistration has
been issued shall cause the certificateofregistration tobemadeavailableon
requesttoan inspectororan approvedinspectionauthority.
(5) A usershall. within seven days afterdiscovering thatthe certificate of
registration has been lost, defaced or destroyed. apply to the provincial
director in the form of Part A of Annexure 2 for the issue of a duplicate
certificate, and affix the fee of R100,00 in the form ofuncancelled revenue
stampstosuchanapplication.
(6) On receiptofan application intermsofsubregulation (5), theprovincial
director shall issue the duplicate certificate ifhe or she is satisfied that the
originalcertificatehasbeen lost, defacedordestroyed.
(7) A user of a steam generator shall immediately notify the provincial
directorinwritingwhen-
(a) suchsteamgeneratoris nolongerin use;
(b) the right of control over the use of the steam generator is
transferred bytheusertoanyotheruser;or
(c) the usermoves the steam generatorto premises otherthanthe
premisesreflected on itscertificateofregistration.
(8) A certificate of registration issued in terms of subregulation (3) shall
lapse-
12 No. 32395 GOVERNMENTGAZETTE, 15JULY2009
(a) uponthetransferoftherightofcontrolovertheuseofthesteam
generatortoanotheruser; or
(b) when asteam generatoris removed from the premisesreflected
on itscertificateofregistration.
Pressureequipmentmarking
9. (1) Every manufacturer of pressure equipment shall cause the
pressure equipmentto be marked in accordancewith the relevanthealth and
safety standard incorporated into these Regulations under section 44 ofthe
Act.
(2) Everymanufacturershallcause adataplateto bepermanentlyfixed in
a conspicuous place to any steam generator or pressure vessel with the
following minimumparticulars:
(a) Nameofmanufacturer;
(b) countryoforigin;
(c) yearofmanufacture;
(d) manufacturer'sserial number;
(e) reference number, date and edition of the health and safety
standard;
(f) designpressurein unitsofPascal;
(g) design temperatureforboth minimum and maximum in degrees
Celsius; .
(h) capacityin cubicmetres;
(i) unique mark ofan approved inspection authority as applicable;
and
G) the hazard category in accordance with the requirements of
SANS347.
(3) In the caseofcomposite pressure equipmentthe following information
shallbe included inadditiontothatreferredto insubregulation(2):
(a) Theresinsystemofthecorrosionbarrierllining;
(b) theresin systemofthestructuralwall; and
(c) the name and specific gravity of the medium for which the
vesselwasdesigned.
STAATSKOERANT. 15 JULIE 2009 No.32395 13
(4) No person may remove a marking or data plate referred to in this
regulation or wilfully damage or alter the particulars marked thereon, except
as provided in this regulation.
(5) A user shall ensure that any modification that changes the original
design conditions is identified by affixing an additional data plate.
(6) A user shall ensure that a data plate is affixed to any steam generator
or pressure vessel that has been re-certified: Provided that where the
manufacturer is unknown, the user responsible for the re-certification shall be
deemed to be the manufacturer.
Pressure and safety accessories
10. (1) No user may require or permit pressure equipment to be used
unless it is provided with all the pressure and safety accessories required by
the relevant health and safety standard which is incorporated into these
Regulations under section 44 of the Act and used in the design, construction
and manufacture of such pressure equipment: Provided that alternative safety
accessories other than those required by the standard may be fitted with the
written approval of an approved inspection authority.
(2) In the absence of a requirement referred to in subregulation (1) in the
relevant health and safety standard which is incorporated into these
Regulations under section 44 of the Act and used in the design, construction
and manufacture of such pressure equipment, safety accessories shall be
provided by the user as required by the approved inspection authority and
those safety accessories shall be so selected, arranged and installed as to be
safe for the particular purpose for which the pressure equipment is to be used.
(3) Every user of a steam generator or pressure vessel shall ensure that
the steam generator or pressure vessel in use is fitted with at least one
pressure measuring device.
(4) Every user of a steam generator or pressure vessel shall ensure that
the steam generator or pressure vessel in use is fitted with at least one safety
valve and that safety valve is kept locked, sealed or otherwise rendered
inaccessible to any unauthorised person.
(5) The number and capacity of the safety valve referred to in
subregulation (4) shall comply with the requirements of the design standard
for the steam generator or pressure vessel or as required in terms of
subregulation (2).
(6) Every user shall ensure that the automatic controls and indicators of a
steam generator, pressure vessel or piping are arranged, installed,
maintained and operated in accordance with the relevant health and safety
standard which is incorporated into these Regulations under section 44 of the
Act and used in the design and manufacture of the steam generator, pressure
vessel or pressurized system: Provided that in the absence of such
14 No.32395 GOVERNMENTGAZETTE, 15JULY2009
provisions, whereautomaticcontrolsand indicatorsareinstalled,theyshallbe
selected, arranged and installed subject to the written approval of an
approvedinspectionauthority.
Inspection and test
11. (1) Subject to the requirements ofthe relevant health and safety
standard incorporated intothese Regulations undersection 44 oftheAct, the
usershallcause-
(a) steam generatorsorpressurevessels, including pressure
and safety accessories, after they are installed or re-
installed and before they are commissioned, to be
subjected to awitnessed internal and external inspection
of a hydraulic pressure test to 1,25 times the design
pressure by an approved inspection authority: Provided
that Category I equipment as categorized in terms of
SANS 347 may be inspected, tested and witnessed by
the user: Provided further that the user may, subject to
the written approval ofan approved inspection authority,
dispense with the internal inspection and hydraulic
pressure test where it could have an adverse effect on
theoperationorintegrityofthepressureequipment;
(b) piping to be inspected and tested by the manufacturer
aftermanufacture, installation, modification or repair and
before commissioning in accordance with the relevant
health and safety standard incorporated into these
Regulations under section 44 of the Act, and, where
applicable, to be witnessed by an approved inspection
authority: Provided that Category I equipment as
categorized in terms of SANS 347 may be inspected,
tested andwitnessed bytheuser;
(c) every fire-tube steam generator to be subjected to an
external inspection every 12 months and a witnessed
hydraulictest and crack detection ofcritical welds every
36 months, by an approved inspection authority for in-
serviceinspectionappointedbytheuserinwriting;
(d) every pressure vessel and steam generator, excluding
those referred to in subregulation (3), to be subjected to
an internaland externalinspectionand ahydraulictestto
a pressure of 1,25 times the design pressure by an
approved inspection authority for in-service inspection
appointed by the user in writing, at intervals not
exceeding 36 months: Provided that Category
equipmentas categorized in terms ofSANS 347 may be
inspected and tested by the user: Provided further that
where the pressure equipment is not subject to
I
STAATSKOERANT, 15JULIE2009 No.32395 15
deterioration processes, the user may dispense with the
internal inspection and hydraulic pressuretest, subjectto
a maximum period ofnineyears forthat pressure vessel
or steam generatorand written approval by an approved
inspection authority: Provided further that the chief
inspector may require a specific steam generator or
pressure vessel to be inspected or tested more
frequently; and
(e) all piping and pipelines to be inspected and tested in
accordancewith the relevant in-servicehealth and safety
standard: Provided that where the health and safety
standard does not prescribe in-service inspections and
test intervals, such intervals shall be determined by a
risk-based inspection applying sound engineering
practice: Providedfurtherthatsuch inspectionandtestfor
CategoryII equipmentand higherascategorized interms
ofSANS 347 shall be performed by acompetent person
referred to in regulation 1 of the General Machinery
Regulations, 1988.
(2) Where itis impracticableto use a liquid forthe hydraulicpressure test
referred to in subregulation (1)(d) or (e), the test may, subject to the prior
written approval of an approved inspection authority, be carried out with an
inertgastoapressureof1,1 timesthedesign pressure: Providedthat, where
reasonably practicable, the test shall be preceded by an internal inspection
and anyconditions and precautionarymeasuresdetermined by the userand
approvedbytheapproved inspectionauthority.
(3) Wherean inspectionortestcarried outintermsofsubregulation (1)(c),
(d) and (e) reveals any weakness or defect whereby the safety of persons
maybeendangered, theweaknessordefectshall be reportedforthwith tothe
user by the person carrying out the inspection or test and the user shall
forthwith cease the use ofthe pressure equipment until such weakness or
defect has been rectified to the satisfaction ofthe person who carried outthe
inspection and the approved inspection authority concerned in cases of
modifications or repairs, as the case may be, or the steam generator,
pressurevessel orstorage vessel hasbeen re-rated to the satisfaction ofthe
approved inspectionauthority_
Risk-based inspection
12. (1) The usermay, asan alternativetothe in-serviceinspection and
testing interval requirements referred to in regulation 11(1)(d), implement a
risk-based inspection management system in accordance with the relevant
health and safety standard incorporated intothese Regulations undersection
44oftheAct.
(2) A risk-based inspection process and implementation shall be verified
byacertificationbodyaccredited bytheaccreditationauthorityintermsofISO
16 No.32395 GOVERNMENTGAZETTE. 15JULY2009
17021 specifically for risk-based inspections and approved by the chief
inspector.
Repairsandmodifications
13. (1) Subject to the requirement of the relevant health and safety
standardincorporated intotheseRegulationsundersection44oftheAct-
(a) any person who intends to modifyorrepair any pressure
equipment shall cause such modification or repair to be
carried out in accordance with the relevant health and
safety standard, and in accordance with the assessment
procedure, as specified by the relevant hazard category
asdeterminedbySANS 347;
(b) any modifier or repairer carrying out any modification or
repair, referred to in paragraph (a), shall issue a
certificate in whichtheextentofthe modification orrepair
is described and certify that such work is in accordance
with the relevant health and safety standard incorporated
into these Regulations under section 44 of the Act:
Provided that such certificate shall be countersigned by
the approved inspection authority, where applicable, as
evidence that the design of such modification has been
verified and that it has been modified or repaired and
tested under its supervision in accordance with the
original health and safety standard where reasonably
practicable;
(c) any user requiring re-certification of any pressure
equipment shall ensure that the re-certification is
performed under the supervision of an approved
inspectionauthority, asapplicable;and
(d) whenever it appears "from any inspection or test that
pressureequipmentcannotbe used safelyin accordance
with its design criteria and the user chooses notto have
the necessary repairs effected immediately, the user
shall, subject to approval by an approved inspection
authority, ensurethatthe pressureequipmentis re-rated,
the amended data plate added and the pressure
equipment operated within the re-rated criteria: Provided
that, in the case of a steam generator, the registration
certificate, together with a copy of the approved
inspection authority's design verification report, shall be
forwarded to the provincial director for updating of the
steamgeneratorregistration.
STAATSKOERANT, 15JULIE2009
NO.32395 17
Records
14. (1) Every user of pressure equipment shall keep a record, which
shall be open for inspection by an inspector, in which the certificate of
manufacture, and the results, after manufacturing, of a" inspections, tests,
modificationsand repairsshallbe recorded.
(2) When pressureequipmentissold, themanufacturershallensurethatit
is accompanied, where relevant, with instructions forthe user, containing a"
thenecessarysafetyinformation relatingto-
(a) mounting, including the assembling of different pieces of
pressureequipment;
(b) puttingintoservice;and
(c) maintenance, includingchecksbytheuser:
Providedthatthoseinstructionsshall coverinformationaffixed tothepressure
equipment in accordance with these Regulations and the relevant health and
safety standard incorporated intothese Regulationsbysection 44 oftheAct,
with the exception of serial identification, and be accompanied, where
appropriate, by technical documents, drawings and diagrams that are
necessaryforafull understanding ofthe instructions: Provided furtherthat, if
appropriate, the instructions shall also refertohazardsarising from misuseof
thepressureequipment.
(3) The manufacturershall keep the original manufacturing records ofthe
pressureequipmentforaminimumperiodof12years.
Access
15. Theusershallcausepressureequipmenttobeerected and maintained
in such a mannerthat access to and exitfrom any chamber, flue, manhole,
inspectionopening, controloraccessoryissafeand unobstructed.
Doorinterlocks
16. (1) Any user of pressure equipment shall cause such pressure
equipmentwhich foroperational purposes is equipped with a quick-actuating
opening, to be provided with an interlock or other effective means for
preventing-
(a) a rise of pressure inside the pressure equipment before the
quick-actuating openings are in the fully closed and locked
position; and
(b) the release ofthe quick-actuating opening from the locked and
closed position before the pressure inside the pressure
equipment has been reduced to atmospheric pressure or the
pressureacrosstheopenings hasbeenequalised.
Gasreticulationequipmentandsystems
18 No. 32395 GOVERNMENTGAZETTE, 15JULY2009
17. (1) Nopersonshall-
(a) handle, store or distribute any gas in any manner. which
includesthe filling ofacontainer, otherthan in accordance with
the relevant health and safety standard incorporated into these
Regulationsundersection44oftheAct;
(b) install or remove an appliance, pressure equipment or system
forgasinanymannerotherthan in accordancewiththerelevant
safety standard incorporated into these Regulations under
section44oftheAct;
(c) install or remove a gas appliance, or a gas system or a gas
reticulation system, unlesssuch person isan authorised person;
or
(d) usepressureequipmentorsystemsforgasin anymannerother
than in accordance with the relevant safety standard
incorporated intotheseRegulationsundersection44oftheAct.
(2) After installation or re-installation. and before commissioning a gas
system. the usershall ensurethat an external inspection and a leaktest are
performed by an authorised person or an approved inspection authority as
applicablein termsofsubregulation(1)(c).
(3) An authorised personoran approved inspection authorityshall issuea
certificate of conformity after completion of a gas installation. modification.
alterationorchangeofuserorownershipintheform ofAnnexure1.
Transportablegascontainers
18. (1) No user shall use. require or permit a transportable gas
containerto be used, and no usershall fill. place in service, handle, modify,
repair, inspect or test any transportable gas container, other than in
compliance with the relevant standards incorporated into these Regulations
undersection44oftheAct.
(2) Theinspection and testreferred to in subregulation (1) shall be carried
outbyan approvedtesting station.
(3) Applications for approval of a testing station shall include proof of
accreditation as prescribed in subregulation (4), and shall includefull contact
detailsand addressinformation.
(4) The chief inspector's approval is subject to a valid accreditation
certificate issued by the accreditation authority: Provided that the chief
inspectormaysetadditional requirementsbeforegrantingapproval.
STAATSKOERANT. 15 JULIE 2009 No.32395 19
Fire extinguishers
19. (1) No user shall use, require or permit the use of a fire extinguisher
unless designed, constructed, filled, recharged, reconditioned, modified,
repaired, inspected or tested in accordance with the relevant safety standard
incorporated into these Regulations under section 44 of the Act.
(2) No person shall fill, recharge, recondition, modify, repair, inspect or test
any fire extinguisher unless such person is an authorised person employed by
a permit holder: Provided that a permit is issued by an organisation approved
by the chief inspector.
(3) Applications for approval shall include proof of accreditation as
prescribed in subregulation (4), and shall include full contact details and
address information.
(4) The chief inspector's approval shall be subject to a valid accreditation
certificate issued by the accreditation authority: Provided that the chief
inspector may set additional requirements before granting approval.
Offences and penalties
20. (1) Any person who contravenes or fails to comply with any of the
provisions of regulations 3, 4, 5,6, 7(1), 7(2), 8(1), 8(2), 8(3), 8(4), 8(5), 8(7),
9,10,11(1).11(3),12(2). 13, 14, 15, 16, 17, 18(1), 18(2), 19(1) and 19(2)
shall be guilty of an offence and liable upon conviction to a 'fine or to
imprisonment for a period not exceeding 12 months and, in the case of a
continuous offence, to an additional 'fine of R200,OO for each day on which the
offence continues or additional imprisonment of one day for each day on
which the offence continues: Provided that the period of such additional
imprisonment shall not exceed 90 days.
Repeal of regulations and annexures
21. The Vessels under Pressure Regulation, 1996, published under
Government Notice No. R. 1591, dated 4 October 1996, is hereby repealed.
Short title
22. These Regulations shall be called the Pressure Equipment
Regulations. 2009, and shall come into effect on 1 October 2009: Provided
that approved inspection authority for in-service inspections shall come into
effect on 1 April 2011 on condition that the inspection shall be carried out by
an authorised person.
--------------
20 No.32395 GOVERNMENTGAZETTE, 15JULY2009
Annexure1
CERTIFICATEOFCONFORMITYFORGASINSTALLATIONS
OCCLIPATIONALHEALTHANDSAFETYACT, 1993
Regulation17(3)ofthePressureEquipmentRegulations,2009
Certificateofconformitybyanauthorised person
I, ,declarethatIamanauthorised
personforgasinstallationswith registration number and 10
number____
Address________________
Telephonenumber( )________
IfurtherdeclarethatIinspectedandtestedtheinstallationat-
Street_________________
Stand number
Nameofbuilding____________
Nameoffarm_____________
Numberoffarm
--=----------
Township/Municipality/District_______
Nameofgassupplier__________-'-
Typeofgas_______________
Amountofgasstoredonpremises kg
and that, in terms of regulation 17(3), the installation complies with the
provisionsof17(2)andthatthe installationissafe.
Iam awarethatIam liable,toprosecutioninthecaseofafalsedeclaration.
Signature Date
-------
--------------
___________________ _
STAATSKOERANT, 15JULIE2009 NO.32395 21
Annexure2
REGISTRATIONOFASTEAMGENERATOR
OCCUPATIONALHEALTHANDSAFETYACT, 1993
Regulation 8(2)ofthe Pressure EquipmentRegulations,2009
Registration ofasteamgenerator
A. APPLICATIONFORREGISTRATIONOFA STEAM
GENERATOR/DUPLICATECERTIFICATE
To:ProvincialDirector From:(PostalAddress)
DepartmentofLabour
Tel._______
Fax
I (user) (legal persona) hereby apply for a registration/duplicate
registrationcertificateofasteamgenerator, particularsofwhich arereflected in PartBbelow.
Signatureofapplicant Date
Nameofapplicant(inblockletters) Designationofapplicant
B. PARTICULARSOFSTEAMGENERATOR
1. Physicaladdressofinstallation__________
2. Typeofsteamgenerator ____________
3. Nameofmanufacturer
4. Countryoforigin______________
5. Yearofmanufacture:----:-___________
6. Manufacturer'sserial number __-:---:---:----:-_____
7. Name, numberand dateofthestandard ofdesign,____
8. Designgaugepressurein pascal__________
9. Maximum permissibleoperating pressurein pascal____
10. Operatingtemperature______________
11. Sourceofenergy(oil, coal, gas,electricityornuclear)___
12. Steamingcapacityofsteamgenerator kg ofsteam perhourfrom and at
100degreesCelsius
13. Nameofapprovedinspectionauthority(during manufacture)____
14. Copyofcertificatefrom manufacturerattached---:----:-__~
15. Copyofapproved inspectionauthority'scommissioningreport
~ c h o o
22 No.32395 GOVERNMENTGAZETTE, 15JULY2009
FOROFFICIALUSEONLY
C. STEAMGENERATORREGISTRATIONCERTIFICATE
Thesteamgenerator,theparticularsofwhichappearin PartB, hasthisday_____
been registeredwiththeofficialnumber ___
Permissionisherebygrantedtousetheboileratamaximumpermissiblepressureof
___kPa.
Signatureofinspector
Official stamp
Issueofduplicatesteamgeneratorregistration certificate
Revenue stamps for duplicate
certificate
Date.______

You might also like