Scribd
Upload
141 views3 pages

Proced I Mien To

The document describes the configuration wizard that runs after terminating autoinstall on a network device. It prompts the user to configure various network settings like the system name, administrative username and password, management interface IP address, default gateway, VLAN, wireless settings, and time settings. After confirming the configuration is correct, the system saves the settings and resets with the new configuration.

Uploaded by

Jona Aguila
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
141 views3 pages

Proced I Mien To

The document describes the configuration wizard that runs after terminating autoinstall on a network device. It prompts the user to configure various network settings like the system name, administrative username and password, management interface IP address, default gateway, VLAN, wireless settings, and time settings. After confirming the configuration is correct, the system saves the settings and resets with the new configuration.

Uploaded by

Jona Aguila
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Procedimiento

Would you like to terminate autoinstall? [yes]: no



*** autoinstall must be terminated in order to run the configuration wizard.


Would you like to terminate autoinstall? [yes]:

System Name [Cisco_31:ad:84] (31 characters max):
AUTO-INSTALL: process terminated -- no configuration loaded

Enter Administrative User Name (24 characters max): admin
Enter Administrative Password (3 to 24 characters): *****
Default values (admin or Cisco or its variants) in password is not allowed.
Enter Administrative Password (3 to 24 characters): *********
Re-enter Administrative Password : *********

Enable Link Aggregation (LAG) [yes][NO]: no

Management Interface IP Address: 192.168.10.10/24
Invalid response


Management Interface IP Address: 192.168.10.10 255.255.255.0
Invalid response


Management Interface IP Address: 192.168.10.10
Management Interface Netmask: 255.255.255.0
Management Interface Default Router: 172.11.0.1

Err: Default Gateway must be on network interface IP subnet

Management Interface Default Router: 10.0.0.10

Err: Default Gateway must be on network interface IP subnet

Management Interface Default Router: 172.11.0.1 255.255.252.0
Invalid response

Management Interface Default Router: ?
Invalid response

Management Interface Default Router: 10.0.0.10/8
Invalid response

Management Interface Default Router: 192.168.10.11
Management Interface VLAN Identifier (0 = untagged): 0
Management Interface Port Num [1 to 4]: 1
Management Interface DHCP Server IP Address: 192.168.10.11

Virtual Gateway IP Address: 1.1.1.1

Multicast IP Address: 239.0.0.10

Mobility/RF Group Name: grupo1

Network Name (SSID): redes1

Configure DHCP Bridging Mode [yes][NO]: no

Allow Static IP Addresses [YES][no]:

Configure a RADIUS Server now? [YES][no]:
Enter the RADIUS Server's Address: 192.168.20.1
Enter the RADIUS Server's Port [1812]:
Enter the RADIUS Server's Secret:
Invalid response

Enter the RADIUS Server's Secret: cisco

Enter Country Code list (enter 'help' for a list of countries) [US]:

Enable 802.11b Network [YES][no]:
Enable 802.11a Network [YES][no]:
Enable 802.11g Network [YES][no]:
Enable Auto-RF [YES][no]:

Configure a NTP server now? [YES][no]: no
Configure the system time now? [YES][no]:
Enter the date in MM/DD/YY format:
Invalid response

Enter the date in MM/DD/YY format: 06/10
Invalid response

Enter the date in MM/DD/YY format: 06/10/14
Enter the time in HH:MM:SS format: 09:08:00

Configuration correct? If yes, system will save it and reset. [yes][NO]:

Configure a NTP server now? [YES][no]: no
Configure the system time now? [YES][no]: no

Warning! No AP will come up unless the time is set.
Please see documentation for more details.

Configuration correct? If yes, system will save it and reset. [yes][NO]: yes

Configuration saved!
Resetting system with new configuration...


Configuration saved!
Resetting system with new configuration...

Updating license storage ...

You might also like