0% found this document useful (0 votes)
305 views5 pages

4.3 The Non-Inverting Amplifier

This document describes the non-inverting operational amplifier configuration. It provides feedback control through a voltage divider network connected from the output to the inverting input. This produces a non-inverting amplifier with high input impedance, low output impedance, and a gain determined by the ratio of the feedback and input resistors. A special case is the voltage follower circuit, which has unity gain feedback and isolates the input from the output while maintaining the input voltage.

Uploaded by

lizhi0007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
305 views5 pages

4.3 The Non-Inverting Amplifier

This document describes the non-inverting operational amplifier configuration. It provides feedback control through a voltage divider network connected from the output to the inverting input. This produces a non-inverting amplifier with high input impedance, low output impedance, and a gain determined by the ratio of the feedback and input resistors. A special case is the voltage follower circuit, which has unity gain feedback and isolates the input from the output while maintaining the input voltage.

Uploaded by

lizhi0007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

4.

3 Non-inverting Operational Amplifier


The Non-inverting Operational Amplifier
The second basic configuration of an operational amplifier circuit is that of a Non-inverting
Operational Amplifier. In this configuration, the input voltage signal, ( Vin ) is applied directly
to the non-inverting ( + ) input terminal which means that the output gain of the amplifier
becomes Positive in value in contrast to the Inverting Amplifier circuit we saw in the last
tutorial whose output gain is negative in value. The result of this is that the output signal is in-
phase with the input signal.
Feedback control of the Non-inverting Operational Amplifier is achieved by applying a small
part of the output voltage signal back to the inverting ( - ) input terminal via a R R2 voltage
divider network, again producing negative feedback. This closed-loop configuration produces a
non-inverting amplifier circuit with very good stability, a very high input impedance, Rin
approaching infinity, as no current flows into the positive input terminal, (ideal conditions) and a
low output impedance, Rout as shown below.
Non-inverting Operational Amplifier Configuration


In the previous Inverting Amplifier tutorial, we said that for an ideal op-amp No current flows
into the input terminal of the amplifier and that V1 always equals V2. This was because the
junction of the input and feedback signal ( V1 ) are at the same potential.
In other words the junction is a virtual earth summing point. Because of this virtual earth node
the resistors, R and R2 form a simple potential divider network across the non-inverting
amplifier with the voltage gain of the circuit being determined by the ratios of R2 and R as
shown below.
Equivalent Potential Divider Network


Then using the formula to calculate the output voltage of a potential divider network, we can
calculate the closed-loop voltage gain ( A
V
) of the Non-inverting Amplifier as follows:


Then the closed loop voltage gain of a Non-inverting Operational Amplifier will be given as:

We can see from the equation above, that the overall closed-loop gain of a non-inverting
amplifier will always be greater but never less than one (unity), it is positive in nature and is
determined by the ratio of the values of R and R2.
If the value of the feedback resistor R is zero, the gain of the amplifier will be exactly equal to
one (unity). If resistor R2 is zero the gain will approach infinity, but in practice it will be limited
to the operational amplifiers open-loop differential gain, ( Ao ).
We can easily convert an inverting operational amplifier configuration into a non-inverting
amplifier configuration by simply changing the input connections as shown.


Voltage Follower (Unity Gain Buffer)
If we made the feedback resistor, R equal to zero, (R = 0), and resistor R2 equal to infinity,
(R2 = ), then the circuit would have a fixed gain of 1 as all the output voltage would be
present on the inverting input terminal (negative feedback). This would then produce a special
type of the non-inverting amplifier circuit called a Voltage Follower or also called a unity gain
buffer.
As the input signal is connected directly to the non-inverting input of the amplifier the output
signal is not inverted resulting in the output voltage being equal to the input voltage, Vout = Vin.
This then makes the voltage follower circuit ideal as a Unity Gain Buffer circuit because of its
isolation properties.
The advantage of the unity gain voltage follower is that it can be used when impedance matching
or circuit isolation is more important than amplification as it maintains the signal voltage. The
input impedance of the voltage follower circuit is very high, typically above 1M as it is equal
to that of the operational amplifiers input resistance times its gain ( Rin x Ao ). Also its output
impedance is very low since an ideal op-amp condition is assumed.
Non-inverting Voltage Follower


In this non-inverting circuit configuration, the input impedance Rin has increased to infinity and
the feedback impedance R reduced to zero. The output is connected directly back to the
negative inverting input so the feedback is 100% and Vin is exactly equal to Vout giving it a
fixed gain of 1 or unity. As the input voltage Vin is applied to the non-inverting input the gain of
the amplifier is given as:


Since no current flows into the non-inverting input terminal the input impedance is infinite (ideal
op-amp) and also no current flows through the feedback loop so any value of resistance may be
placed in the feedback loop without affecting the characteristics of the circuit as no voltage is
dissipated across it, zero current flows, zero voltage drop, zero power loss.
Since the input current is zero giving zero input power, the voltage follower can provide a large
power gain. However in most real unity gain buffer circuits a low value (typically 1k) resistor
is required to reduce any offset input leakage currents, and also if the operational amplifier is of a
current feedback type.
The voltage follower or unity gain buffer is a special and very useful type of Non-inverting
amplifier circuit that is commonly used in electronics to isolated circuits from each other
especially in High-order state variable or Sallen-Key type active filters to separate one filter
stage from the other. Typical digital buffer ICs available are the 74LS125 Quad 3-state buffer or
the more common 74LS244 Octal buffer.
One final thought, the closed loop voltage gain of a voltage follower circuit is 1 or Unity. The
open loop voltage gain of an ideal operational amplifier with no feedback is Infinite. Then by
carefully selecting the feedback components we can control the amount of gain produced by a
non-inverting operational amplifier anywhere from one to infinity.
Thus far we have analysed an inverting and non-inverting amplifier circuit that has just one input
signal, Vin. In the next tutorial about Operational Amplifiers, we will examine the effect of the
output voltage, Vout by connecting more inputs to the amplifier. This then produces another
common type of operational amplifier circuit called a Summing Amplifier which can be used to
add together the voltages present on its inputs.

You might also like