LC1900SS 4-Wheel Steer Trailer Cart

LIMITED WARRANTY
This unit is warranted against defects in materials and workmanship to the original purchaser, under normal
use and service for a period of ninety (90) days from the date of sale. During the Warranty Period, we will repair or
replace, at our option, free of charge to the original purchaser, any part of the unit that our examination shows to
be defective in workmanship or materials.
This Warranty does not apply to damage in transit or damage caused by misuse, abuse, neglect, normal wear,
or alterations by unauthorized persons.
4750-2
4/08
Complete Parts List for the LC1900SS Trailer Cart
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Cart Body
Wheel
Undercarriage Assembly
Long Tow Bar
Tailgate
Tie Bar
Steering Bar
Steering Adjustment Bar
Short Tow Bar
Pivot Bar Assembly
Clevis Plate
Steering Link
1/2 x 4 Clevis Pin
1/8 x 1-1/4 Cotter Pin
2 x 2 Tube Plug
1/2 x 1-3/4 Clevis Pin
#14 Hitch Pin Clip
1/2 x 4 Shoulder Bolt
3/8" Lock Washer
4782GY
4425Z
4774GY
4435GY
5631GY
4786GY
4761GY
4760GY
4437GY
4787GY
1243GY
4755GY
4447
1262
1443
1840
1042
4791
1274
3/4 Flat Washer
1-1/2 x 1-1/2 Tube Plug
3/8 x 2-1/4 Shoulder Bolt
5/16 Lock Washer
3/8 x 3/4 Hex Head Bolt
3/8 Hex Head Nut
1/2 Flat Washer
5/16 x 1-1/2 Hex Head Bolt
3/8 Reverse Lock Nut
5/16 x 3/4 Hex Head Bolt
5/16 Hex Head Nut
Short Spindle Assembly
Long Spindle Assembly Weld
Flange Metal Bearing
Axle Boss Tube Drilled
Welded Undercarriage Assembly
5/16" Reverse Lock Nut
3/8 " Flat Washer
1 x 1/2 Spacer
1264
4751
4785
1276
1272
1273
1506
4014
3039
1248
1275
4768
4770
4232
4267
4774-1
1557
1278
4295
1
4
2
1
2
2
1
1
1
1
1
2
1
13
4
1
2
1
16
9
6
1
6
16
16
21
4
1
2
6
1
1
4
2
2
1
3
4
Ref. No.
Part Description Part No. Qty. Ref. No. Part Description Part No. Qty.
13
14
14
14
14
14
14
14
15
16
17
17
18
20
20
22
23
23
23
24
25
37
26 26
26
26
26
26
26
26
26
26
26
26
26
27
28
30
30
30
30
26
2
3
4
5
6
7
8
9
10
11
29
12
19
21
27
1
12
31
32
33
33
34
33
33
35
36
37
Page 2 Page 7
Your LC1900SS includes the feature of having the rear
Undercarriage Assembly lock into place.
To lock the rear wheels into place, simply remove the
#14 Hitch Pin Clip and Flat Washer from the Steering
Adjustment Bar attached to the Pivot Bar Assembly.
Next, place the Steering Adjustment Bar over the
Locking Post and secure with the Flat Washer and
#14 Hitch Pin Clip.
NOTE: It is advised to lock the rear wheels
while the cart is empty.
Locking the Rear Wheels
Adjusting the Rear Wheels
If your LC1900SS ever trails behind you wrong due
to improper alignment you can adjust the rear wheels
using the Steering Adjustment Bar. Simply loosen the
two Jam Nuts (one nut is a right-handed thread and
the other nut is a left-handed thread) located on each
side of the Coupler. Twist the Coupler to lengthen or
shorten the Steering Adjustment Bar. Turn the Coupler
until the wheels are square with the front wheel
assembly. When adjustment is complete re-tighten the
Jam Nuts to keep the Coupler in place.
Jam
Nut
Coupler
Jam
Nut
Steering
Adjustment Bar
LC1900SS Components & Hardware List for Assembly
2
3
4
5
6
7
8
10
9
11
13
13
14
15
16
17
18
19
20 21
22
23
24 25
26
27
28
29 30
Cart Body
Wheel
Undercarriage Assembly
Long Tow Bar
Tailgate
Tie Bar
Steering Bar
Steering Adjustment Bar
Short Tow Bar
Pivot Bar Assembly
Clevis Plate
Steering Link
Spacer 1 x
1
2
3
4
5
6
7
8
9
10
11
12
13
1
4
2
1
2
2
1
1
1
1
1
2
4
1/2 x 4 Clevis Pin
1/8 x 1-1/4 Cotter Pin
2 x 2 Tube Plug
1/2 x 1-3/4 Clevis Pin
#14 Hitch Pin Clip
1/2 x 4 Shoulder Bolt
3/8 Lock Washer
3/4 Flat Washer
1-1/2 x 1-1/2 Tube Plug
3/8 x 2-1/4 Shoulder Bolt
5/16 Lock Washer
3/8 x 3/4 Hex Head Bolt
3/8 Hex Head Nut
1/2 Flat Washer
5/16 x 1-1/2 Hex Head Bolt
3/8 Reverse Lock Nut
5/16 x 3/4 Hex Head Bolt
5/16 Hex Head Nut
5/16 Reverse Lock Nut
3/8 Flat Washer
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
13
4
1
2
1
16
9
6
1
6
16
16
21
4
1
2
6
1
3
Ref. No. Description Qty.
LC1900SS Assembly:
1/4 Hex Key (Allen) Wrench
1/2 Wrenches
9/16 Wrenches
Pliers
Hammer
Tools Required for
CUSTOMER SUPPORT
At Precision Products, Inc. delivering quality, value and
outstanding service is our goal. However, sometimes parts
do become damaged or lost during transport from our
facilities to the store. If you have any problems, please
do not return this merchandise to the store. Call us
and we will take care of any problem you may have
with this unit.
When ordering replacement parts, please
have the model number, part description
and part number available.
MAINTENANCE:
* Grease Wheels at regular intervals, at least
every six months, more frequently if used
regularly.
* Check tire pressure at regular intervals.
Proper inflation will prolong life of tire.
* Grease all moving joints at regular intervals.
TRAILER CART LIMITATIONS:
2,000 Lbs. Maximum Capacity
Approximate weight (1) Cu. Ft.
DIRT-150# SAND-125# GRAVEL-110#
Max. Speed 5 MPH
WARNING OF DANGER OF IMPROPER USE OF THIS TRAILER CART. THIS UNIT IS INTENDED FOR USE ONLY WITH
RIDING MOWERS OR GARDEN TRACTORS. IT IS DEFINITELY NOT FOR HIGHWAY USE, BEING PULLED AT HIGH
SPEEDS, OR TRANSPORTING PASSENGERS OF ANY SORT. SUCH USE COULD RESULT IN INJURIES FOR WHICH WE
CANNOT BE HELD RESPONSIBLE.
Assembly Tips:
* Make sure you have all the necessary components and hardware before assembling the trailer cart.
If any components are missing, please contact a Customer Service Representative.
* Have another person available to help maneuver the trailer cart while assembling.
* It may be necessary to remove excess paint when assembling some moving components.
If the fit is too tight, use some medium grit sandpaper to remove the paint. Apply grease
or oil to the joint to keep a smooth operation and fight corrosion.
Send To: Precision Products, Inc.
316 Limit Street
Lincoln, IL 62656
Toll Free (800) 225-5891
Phone (217) 735-1590
Fax (217) 735-2435

Visit us on the web: www.precisionprodinc.com
USING YOUR LC1900SS TRAILER CART:
* Do not allow children to operate the tractor while towing the trailer cart.
* It is recommended that you do not attempt to back this trailer cart while moving into a desired space. Due to the
4-Wheel-Steer set up with a tight turning radius, the trailer cart is more probable to jack-knife and cause damage to
your tractor and/or the cart itself.
* Always load your trailer cart on a level surface. Sharp inclines can cause severe instability.
* Center loads onto the trailer cart.
* Do not tow this trailer cart on any kind of steep slopes.
* Your tractors stability and braking abilities will be affected with the attachment of this trailer cart. Check your vehicles
owners manual for its capabilities for pulling and general operation with attachments.
* Reduce your speed while towing this trailer cart over rough surfaces.
.
Part No. Ref. No. Description Qty. Part No.
4782GY
4425Z
4774GY
4435GY
5631GY
4786GY
4761GY
4760GY
4437GY
4787
1243GY
4755GY
4295
4447
1262
1443
1840
1042
4791
1274
1264
4751
4785
1276
1272
1273
1506
4014
3039
1248
1275
1557
1278
Pivot Bar
Assembly
Steering
Adjustment Bar
Locking
Post
31
32
12
LC1900SS Assembly Instructions
Attach the Tie Bar to the Undercarriage Assembly using two (per end) 1/2 Flat Washers and a 1/8 x 1-1/4 Cotter Pin.
Insert two 2 Tube Plugs into both open ends of the Undercarriage Assembly as shown below.
2 Tube Plug
1/2 Flat Washers
1/8 x 1-1/4 Cotter Pin
2 Tube Plug
1/2 Flat Washers
1/8 x 1-1/4 Cotter Pin
Tie Bar
Attach both Undercarriage Assemblies to the Cart Body using 3/8 x 3/4 Hex Head Bolts, 3/8 Lock Washers and 3/8 Hex Head
Nuts. The Undercarriage Assemblies MUST be assembled as shown below. The Steering Links on the Undercarriage Assemblies
must be on the same side of the Cart Body as the Pivot Post and Locking Post.
Undercarriage Assembly
Pivot
Post
Locking
Post
Steering Link
Cart Body
Steering Link
Undercarriage Assembly
3/8 x 3/4 Hex
Head Bolt
3/8 Lock
Washer
3/8 Hex
Head Nut
Undercarriage
Assembly
Page 6 Page 3
Attach the wheels to the cart by putting a 1 x 1/2 Spacer over the Axle followed by a 3/4" Flat Washer then the Wheel
a final 3/4 Flat Washer and secure in place with a 1/8 x 1-1/4 Cotter Pin. Repeat procedure for the other three Wheels.
3/4 Flat
Washer
Wheel
1/8 x 1-1/4
Cotter Pin
3/4 Flat
Washer
Axle
Carefully turn the trailer cart over onto its wheels. Insert the two Tailgates into both ends of the trailer cart.
Gently tap six, 1-1/2 Tube Plugs into all of the open ends on the trailer cart body frame..
1-1/2 Tube Plugs
Tail Gate
Tail Gate
Slot in Trailer
Cart Body
Spacer
Spacer
Attach the Pivot Bar Assembly to the Pivot Post using a 3/4 Flat Washer and a 1/8 x 1-1/4 Cotter Pin.
Place 1/2 Flat Washers over both posts on the Pivot Bar Assembly and over the posts on both Steering Links.
Steering Link
3/4 Flat
Washer 1/8 x 1-1/4
Cotter Pin
Pivot Post
Pivot Bar
Assembly
1/2 Flat
Washer
1/2 Flat
Washer
1/2 Flat
Washer
Steering Link
Connect the Steering Adjustment Bar to both the rear Undercarriage Assembly and the outer pin on the Pivot Bar Assembly using two
1/2 Flat Washers a 1/8 x 1-1/4 Cotter Pin and a #14 Hitch Pin Clip (attaches to the outer pin on the Pivot Bar Assembly).
Connect the Steering Bar to the inner pin on the Pivot Bar Assembly and the front Undercarriage Assembly using two 1/2 Flat Washers and
two 1/8 x 1-1/4 Cotter Pins.
1/8 x 1-1/4
Cotter Pin
1/2 Flat
Washer
Pivot Bar
Assembly
Rear Undercarriage
Assembly
Front Undercarriage
Assembly
Steering Adjustment
Bar
Steering Bar
1/2 Flat
Washers
1/2 Flat
Washer
1/8 x 1-1/4
Cotter Pin
1/8 x 1-1/4
Cotter Pin
Attach the Short Tow Bar to the front Undercarriage Assembly by passing a 1/2 x 4 Shoulder Bolt through a 1/2 Washer, the
two pivot plates (on the Undercarriage Assembly), another 1/2 Flat Washer, the Short Tow Bar, a final 1/2 Flat Washer and secure
with a 3/8 Reverse Lock Nut.
Insert the 3/8 x 2-1/4 Shoulder Bolt through a 3/8 Flat Washer, center hole in the Tie Bar, 3/8" Washer, Short Tow Bar, then a 3/8
Flat Washer and secure with a 5/16 Reverse Lock Nut.
3/8 x 2-1/4
Shoulder Bolt
Tie Bar
Short Tow Bar
3/8 Flat
Washer
3/8 Reverse
Lock Nut
3/8 Flat
Washers
1/2 x 4
Shoulder Bolt
Pivot Plates
1/2 Flat
Washer
1/2 Flat
Washer
Connect the Long Tow Bar to the Short Tow Bar by passing a 1/2 x 4 Clevis Pin through the ends of the Long Tow Bar and
Short Tow Bar. Secure the 1/2 x 4 Clevis Pin using 1/2 Flat Washer and a 1/8 x 1-1/4 Cotter Pin.
Attach the Clevis Plate to the end of the Long Tow Bar using two 5/16 x 3/4 Hex Head Bolts, 5/16 Lock Washers and
5/16 Hex Head Nuts. Insert the 1/2 x 1-3/4 Clevis Pin through the Clevis Plate and Long Tow Bar and secure with a #14 Hitch
Pin Clip.
1/2 x 4
Clevis Pin
1/2 Flat
Washer
Clevis Plate
5/16 x 3/4
Hex Head Bolts
1/2 x 1-3/4
Clevis Pin
#14 Hitch
Pin Clip
5/16 Lock
Washers
5/16 Hex
Head Nuts
Long Tow
Bar
Short Tow
Bar
1/8 x 1-1/4
Cotter Pin
Page 4
Page 5
#14 Hitch
Pin Clip
5/16 Reverse
Lock Nut