DESIGN GUIDE

IP-Surveillance design guide

Setting up an IP-Surveillance system using Axis network cameras,
video encoders and AXIS Camera Station software
Table of contents
This document is a guide to setting up an IP-Surveillance system in a
small- to medium-sized security installation. It provides an overview
of network videos functionalities and benefits, and outlines
considerations and recommendations for implementing such a
system.
1. Introduction to an IP-Surveillance system 3
2. Component considerations 10
3. Mounting surveillance cameras 27
4. Server selection 31
5. AXIS Camera Station installation and configuration 34
6. Video motion detection 39
7. Daily operation 40
8. Scaling up your surveillance system 45
9. Conclusion 48
10. Appendix: Letter chart 49
3
Introduction to an IP-Surveillance system
This chapter provides an overview of what is involved in an IP-Surveillance system, the benefits of net-
work video, the importance of defining your surveillance application and legal considerations to take
into account when setting up an IP-Surveillance system in your area.
What is IP-Surveillance?
IP-Surveillance is a term for a security system that gives users the ability to monitor and record video
and/or audio over an IP (Internet Protocol-based) computer network such as a local area network (LAN)
or the Internet. In a simple IP-Surveillance system, this involves the use of a network camera (or an ana-
log camera with a video encoder/video server), a network switch, a PC for viewing, managing and storing
video, and video management software. (More detailed discussions of the components are provided in
Chapter 2.)
Figure 1.1.a. An IP-Surveillance or network video system
Unlike analog video systems that use dedicated point-to-point analog cabling from the camera location
to the viewing/recording station, IP-Surveillance (or network video) uses the IP network technology as
the backbone for transporting information. In an IP-Surveillance application, digitized video and/or audio
streams can be sent to any locationeven around the world if desiredvia a wired and/or wireless IP
network, enabling video monitoring and recording from anywhere with network access.
Figure 1.1.b. An analog video system that incorporates a DVR (digital video recorder)
While an analog video system is for the most part a one-directional signal carrier that ends at the re-
cording device, a network video system is bi-directional (allowing information to be sent and received)
and can be an integrated part of a larger, scalable system. A network camera, for instance, can send
video, audio and other data (e.g., SMS) to a user, as well as receive from the user audio and data instruc-
tions that could, for example, activate doors or external alarms. In addition, a network video system can
communicate with several applications in parallel and perform various tasks such as detecting motion or
sending different streams of video. Such a system provides for greater performance possibilities and
flexibility.
1.
1.1.
PoE switch
Network cameras Computer with video
management software
LAN
LAN/Internet
Analog Coax
Cabling DVR
Monitor
Analog
cameras
4
Figure 1.1.c. A network video system with alarm integration
Because of the digital nature and method of video distribution, IP-Surveillance provides a host of ben-
efits and advanced functionalities that gives you greater control and management of live and recorded
video, as well as alarm events. This makes the system highly suited to security surveillance applications.
The advantages include:
1) Remote accessibility: You can access live and recorded video at any time and from virtually any
networked location in the world. Multiple, authorized users at different locations may be able to
access live or recorded video. This is advantageous if your company wants a third-party, such as a
security firm, to benefit from and have access to the video. In a traditional analog CCTV system,
you need to be in a specific, on-site monitoring location to view and manage video, and off-site
video access would not be possible without some additional equipment, such as a video encoder or
a network DVR (digital video recorder).
2) High image quality: High image quality is essential in a security surveillance application. You want
to be able to clearly capture an incident in progress and identify persons or objects involved. In a net-
work video system, the quality of images produced can be more easily retained than in an analog sur-
veillance system. With an analog video system, the captured images are degraded with every conversion
that the images make between analog and digital formats and with the cabling distance. The further the
analog video signals travel, the weaker they become. In a fully digital IP-Surveillance system, images
from a network camera are digitized once and they stay digital with no unnecessary conversions and no
image degradation due to distance traveled. In addition, digital images can be more easily stored and
retrieved than is the case with the use of analog video tapes.
A network camera that uses progressive scan technology provides clearer images of moving objects
because the whole image is presented at one time. With an analog video signal, two consecutive inter-
laced fields of lines are presented to form an image, and when displayed on a PC monitor, blurriness
occurs when objects move between the image capture of the two interlaced fields.

Figure 1.1.d. Progressive scan Figure 1.1.e. Analog interlaced scan
PIR
detector
Computer with video
management
software
Home
Office
INTERNET
Mobile
telephone
Video
recording
server
IP NETWORK
Relay
Alarm siren
Analog camera
Axis network
camera
5
A megapixel network camera (i.e. one that delivers an image comprised of 1 million or more pixels)
can also offer resolutions greater than what an analog camera can offer, which means that more
detail or larger areas can be covered.




Figure 1.1.f. Integration with Point of Sales system
3) Easy, future-proof integration: Network video products based on open standards can be easily
integrated with computer and Ethernet-based information, audio and security systems, video
management and application software, and other digital devices. For instance, a network camera
can be linked to specialized software programs that could, for example, integrate video with a
Point of Sales system, or analyze the visual and/or audio data to detect wanted persons in a crowd
or unauthorized access to specific areas.
4) Scalable and flexible: An IP-Surveillance system can grow with your needs. You can add as many
network video products to the system as desired without significant or costly changes to the
network infrastructure. You can place and network the products from virtually any location, and the
system can be as open or as closed as you wish.
5) Cost-effective: An IP-Surveillance system has a lower total cost of ownership than a traditional
analog CCTV surveillance. Management and equipment costs are lower since back-end applica-
tions and storage run on industry standard, open systems-based serversnot on proprietary hard-
ware such as a DVR in the case of an analog CCTV system. Additional cost savings come from the
infrastructure used. IP-based video streams can be routed around the world using a variety of
interoperable infrastructure. IP-based networks such as LANs and the Internet, and various
connection methods such as wireless are much less expensive alternatives than traditional
coaxial and fiber needed for an analog CCTV system. In addition, an IP infrastructure can be
leveraged for other applications across the organization.
Furthermore, Power over Ethernet (PoE) technology, which cannot be applied in an analog video
system, can be used in a network video system to increase savings and reliability.
6

Figure 1.1.g. A system that uses Power over Ethernet (PoE). A PoE-supported network camera connects directly to a PoE-
enabled switch, while a network camera without built-in PoE support can use an active splitter to make use of PoE.
PoE enables networked devices to receive power from a PoE-enabled switch or midspan through
the same standard cable that transmits data (video). Hiring a certified electrician and installing a
separate power line are not neededa big advantage, particularly in difficult-to-reach areas. With
PoE, network cameras/video encoders will also be able to receive centralized backup power from a
server room with an Uninterruptible Power Supply; so in the event of a power failure, the cameras/
video encoders will still be able to operate. (See diagram above.)
6) Event management and intelligent video: There is often too much video recorded and lack of
time to properly analyze them. Advanced network cameras/video encoders with built-in intelli-
gence or analytics take care of this by reducing the amount of uninteresting video recorded and
enabling programmed responses.
Advanced network cameras/video encoders have such features as built-in video motion detection,
audio detection alarm, active tampering alarm, I/O connections, and alarm and event management
functionalities. These features enable the network cameras/video encoders to be constantly on guard in
analyzing inputs and waiting for an impulse to kick-start an action or a series of actions. Having intel-
ligence/analytics conducted at the network camera/video encoder rather than at the recording server
reduces network bandwidth usage and storage needs since only actionable data (video) is sent over the
network. In addition, less computing power is required from the recording server.
Event management functionalities can be configured using the network video product user
interface or a video management software program. Users can define the alarms/events by setting
the type of triggers to be used and when, as well as the responses (e.g., recording to one or
multiple siteswhether local and/or off-site for security purposes; activation of external devices
such as alarms, lights and doors; and notification messages to users).
Figure 1.1.h. Setting up an event trigger using the network cameras user interface.
PoE-enabled switch
Uninterruptible Power
Supply (UPS)
3115
Network camera
with built-in PoE
Network camera
without built-in
PoE
P o we r D s in e 4 0 0 1
Active
splitter
Power Power over Ethernet
7
A security personnels ability to protect people, property and assets can be enhanced by the flexibility
and power of IP-Surveillance technology. IP-Surveillance systems have been installed in indoor/outdoor
and private/public spaces; for example, in stores, homes, day care centers, schools, banks, government
offices, factories, warehouses, railway/subway stations and airports.
Overview of an IP-Surveillance system
An IP-Surveillance system can be as simple or as sophisticated as your needs require. In a simple sce-
nario, you have a PC where you want to view and record video. You have an Ethernet cable between a
PC and a network switch (which allows different devices to connect to each other and share, for in-
stance, a common Internet connection) and a cable from the switch to the camera location. You then
need equipment that can capture video and send a video stream over the network. This can be a network
camera, or an analog camera connected to a video encoder (also sometimes known as a video server).

Figure 1.2.a Overview of an IP-Surveillance system
A network camera or a video encoder connects directly to the networknot to a PC as is the case with
a web camera. Once the network camera (or analog camera and video encoder) is installed and config-
ured, you can view and record live video using a web browser on a local PC or a remote PC via the Inter-
net. If you want to access and record video from many cameras simultaneously, it is advisable to install
a video management software program on the recording PC.
As mentioned earlier, an IP-Surveillance system is easy and cost-effective to scale up. It is also flexible,
and each component of the system can be customized to your needs. The following is a brief overview
of the components that can be tailored to your application:
a) Network camera/video encoder: A wide variety of network cameras and video encoders are avail-
able. Network cameras range from fixed cameras and fixed domes, to pan/tilt/zoom (PTZ) and PTZ
dome cameras, and may be designed for use indoors or outdoors. Other network camera features in-
clude built-in support for wireless communication, megapixel resolutions and vandal resistance. Both
network cameras and video encoders may offer a variety of capabilities such as: 1) several simultane-
ous video streams using different video compression formats (e.g. H.264, MPEG-4 Part 2, Motion JPEG)
that are optimized for bandwidth and image quality; 2) input/output ports for connection to external
devices such as sensors and alarms; 3) built-in intelligence such as video motion detection and tamper-
ing detection; 4) sophisticated alarm and event management functions that can communicate with
different devices and applications simultaneously, and can send separate video streams in different
resolutions, at different frame rates and to different places; 5) audio support; and 6) Power over Eth-
ernet, which enables power to be delivered over the same cable as for data transmission.
1.2.
AXIS Q7406 Video Encoder Blade
AXIS Q7406 Video Encoder Blade
0 -
0 -
AXIS Q7900 Rack
100-240 50-50 Hz 4-2 A
FNP 30
Power-one
AC
ACTIVITY
LOOP
NETWORK
1 2 3 4
PS1 PS2 FANS
POWER
POWER
100-240 AC 50-50 Hz 4-2 A
FNP 30
Power-one
AC
Computer with
video management
software
Axis network cameras
Axis video encoders
Computer
with web
browser
Web
browser
Office
Home
Analog
cameras
IP NETWORK
INTERNET
AUDIO
I/O
IN
OUT 1 2 3 4 5 6
8
b) Network: There are many ways to design and secure a network for IP-Surveillance. In addition, a
network can be as small or as extensive as your requirements, and it can be wired, wireless or a com-
bination of both. It is also easy to increase the bandwidth capacity of your network simply by adding
switches/routers. And different technologies can be used to optimize bandwidth usage. Furthermore,
a wired network can deliver not only data, but also power using Power over Ethernet (PoE) technol-
ogy. This simplifies installation of PoE-enabled network cameras/video encoders and provides cost
savings.
c) Hardware (server and storage): The hardware requirements of an IP-Surveillance system are not
complex. Simply use standard components found in the IT industry. Todays PC, with a Pentium pro-
cessor and Windows operating system, is able to run a video management software, and record and
store video from up to 50 cameras. If the hard disk on the actual server running the recording applica-
tion is not enough, there are solutions that enable you to increase storage space and achieve in-
creased flexibility and recoverability. As larger hard drives are produced at lower costs, it is becoming
less expensive to store large amounts of video.
d) Software: A wide range of software is available to help you in the preparation, installation and
management of an IP-Surveillance system. For example, you can use the AXIS Design Tool, which
helps you estimate how much bandwidth your network video system will require, and installation
software such as the AXIS Camera Management (free download), which makes it easier for you to
find, install and configure the video products on the network. A video management software is also
recommended. It will allow you to, among other things, centrally manage and configure the network
video products to your viewing, recording and security preferences.

Figure 1.2.c. AXIS Camera Management software
A more detailed discussion of the components and the considerations to take into account when select-
ing equipment is provided in Chapter 2.
9
1.4.
Defining your surveillance application
The first and most important step in implementing a
video surveillance installation is determining the goal
of your surveillance application. It is a good idea to
map out where you want video surveillance to take
place and for what purpose (i.e. surveillance overview,
identification, people counting). This will determine the
type and number of network cameras, as well as other
components to install and can influence the overall
cost of the installation. More information about how to
select a network camera and other components is cov-
ered in Chapter 2.
Legal considerations
Video surveillance can be restricted or prohibited by laws that vary from
country to country. It is advisable to check the laws in your local region
before installing a video surveillance system. There may be legislation or
guidelines covering the following:
a) License. You may need to register or get a license from an authority to
conduct video surveillance, particularly in public areas.
b) Purpose of the surveillance equipment. Is it in accordance with what
is permitted by the laws in your area?
c) Position or location of the equipment. Is it positioned or located in such a way that it only
monitors the spaces which the equipment is intended to cover, and if unintended areas are covered,
would you have to consult with the owners of such spaces? There may be rules covering areas where
video surveillance is prohibited; for example, toilets and changing rooms in a retail environment.
d) Notification. You may have to place signs to warn the public that they are entering a zone covered
by surveillance equipment and there may be rules regarding the signage.
e) Quality of images. There may be rules regarding the quality of images, which can affect what may
be permitted or acceptable for use as evidence in court.
f) Video format. Police authorities may require that the video format be ones that they can handle.
g) Information provided in recorded video. Video recordings, for instance, may be required to have
time and date stamped.
h) Processing of images. There may be rules regulating how long images should be retained, who can
view such images and where recorded images can be viewed. You may have to keep an audit log.
i) There may be requirements for drawings of where cameras are placed.
j) Personnel training. There may be regulations that require operators to be trained in security and
disclosure policies, as well as privacy issues.
k) Access to and disclosure of images to third parties. There may be restrictions on who can access
the images and how images can be shown. For example, if video is to be disclosed to the media, im-
ages of individuals may have to be disguised or blurred.
l) Recording of sound. A permit may be required for recording sound in addition to video.
m) Regular system checks. There may be guidelines on how often and thorough a company should
perform system checks to make sure all equipment are operating as they should.
1.3.
10
Component considerations
This chapter describes the major components of an IP-Surveillance system, and provides guidelines for
selecting equipment. The components covered in this chapter include network camera, video encoder,
network switch, server hardware and video management software (AXIS Camera Station).
Network camera
A network camera can be described as a camera and computer combined in one unit. It has a compres-
sion chip, an operating system, a built-in web server, FTP (File Transfer Protocol) server, FTP client, e-mail
client, alarm management and much more. A network camera, unlike a web camera, does not need to be
attached to a PC; it operates independently and connects, as with a PC, directly to an IP network. It can
be placed wherever there is a wired or wireless network connection. The network camera captures and
sends live images, enabling authorized users to locally or remotely view, store and manage video over a
standard IP-based network infrastructure.














Figure 2.1.a. Inside an Axis network camera Figure 2.1.b. Back of an Axis network camera
Many types of network cameras are available today, and no matter what your needs are, there is a net-
work camera available to meet them. Although analog cameras are available in a similar variety, network
cameras can now offer more benefits, including better image quality and greater installation flexibility.
For some special applications, such as very high image resolution or wireless needs, network cameras are
the only option.
The following sections provide an overview of the types of network cameras available, the network
camera features to consider and how to select a network camera.
a) Types of network cameras
Axis offers the widest range of professional network cameras on the market. Network cameras can
be categorized into indoor/outdoor versions and types.
> Indoor or outdoor. Outdoor network cameras must
have an auto iris lens to regulate how much light is
received. Many outdoor cameras require a protective
housing. Others may already be designed with a
protective enclosure. Housings are also available for
indoor cameras that require protection from harsh environments such as dust and humidity, and
from vandalism or tampering.

> Types: Fixed, fixed dome, PTZ (pan/tilt/zoom) or PTZ dome
2.
2.1.
CPU
Image
Processor
Compression
Flash
Memory
DRAM
Ethernet
Interface
Image
Sensor
Lens
Optical Filter
Power connector
DC-Iris
control cable
I/O terminal
connector
RJ-45 Ethernet network connector
(and Power over Ethernet depending on model)
11
Fixed network cameras
A fixed camera is one whose viewing angle is fixed once it is mounted. A fixed camera with a body and
a lens represents the traditional camera type. In some applications, it is advantageous to make the
camera very visible. If this is the case, then a fixed camera represents the best choice since both the
camera and the direction in which it is pointing are clearly visible. Another advantage is that most fixed
cameras have exchangeable lenses. For further protection, fixed cameras can be installed in housings
designed for indoor or outdoor installation.
Figure 2.1.d. AXIS 211 Network Camera
Fixed dome network cameras
Fixed dome cameras, also called mini domes, essentially consist of a fixed camera that is pre-installed
in a small dome housing. The camera can be easily directed to point in any direction. Its main benefit
lies in its discreet, non-obtrusive design, as well as in the fact that it is hard to see in which direction
the camera is pointing. The camera is also tamper resistant. A limitation of a fixed dome camera is
that it rarely comes with a changeable lens, and even if it is changeable, the choice of lenses is lim-
ited by the space inside the dome housing. However, a varifocal lens is often provided, which enables
the cameras field of view to be adjusted. Fixed dome cameras are designed with different types of
enclosures such as vandal-resistant and/or IP66-rated enclosures for outdoor installations. No exter-
nal housing is required. The mounting of such a camera is usually on a wall or ceiling.
Figure 2.1.e. AXIS 216FD Network Camera
PTZ network cameras
The cameras view can be remotely controlled, either manually or automatically, for panning from side
to side, tilting up and down, and zooming in and out of an area or object. There are now mechanical
as well as non-mechanical PTZ cameras.
Mechanical PTZ cameras can pan, tilt and zoom through manual or automatic control. In a manual
operation, an operator can use a PTZ camera to follow, for instance, a person in a retail store. PTZ
cameras are mainly used indoors and in applications where an operator is employed and where the
visibility of the cameras viewing angle is desirable or not an issue. The optical zoom on PTZ cameras
typically ranges from 10X to 26X. A PTZ camera can be mounted on a ceiling or wall.
Figure 2.1.f. AXIS 214 PTZ Network Camera
12
A difference between PTZ cameras and PTZ domes is that many PTZ cameras do not have full 360-de-
gree pan due to a mechanical stop that prevents the cameras from making a continuous circular
movement. It means that the camera cannot follow a person walking continuously in a full circle
around the camera. An exception is the AXIS 215 PTZ Network Camera, which thanks to its auto-flip
functionality, can instantly flip the camera head 180 degrees and continue to pan beyond its zero
point. The camera can then continue to follow a passing person or object, regardless of the direction.
Another difference between PTZ cameras and PTZ domes is that PTZ cameras are not made for con-
tinuous automatic operation or so-called guard tours.

Figure 2.1.g. AXIS 215 PTZ Network Camera in drop-ceiling mount
A non-mechanical PTZ camera uses a megapixel sensor and a wide-angle lens to enable it to have a view-
ing angle of 100 degrees to 180 degrees (or even wider in same cases). Such a camera allows an operator
to zoom in on any part of a scene without any mechanical movement. The key advantage is that there is
no wear and tear since the camera has no moving parts. Zooming in on a new area of a scene is immedi-
ate. In a traditional PTZ camera, this can take up to 1 second. Since a non-mechanical PTZ cameras
viewing angle is not visible, it is ideal for discreet installations. To obtain good image quality, pan, tilt and
zoom should be limited. If such a camera has a 3 megapixel sensor, the recommended maximum viewing
angle is 140 degrees with a 3X zoom capability. This type of camera is typically mounted on a wall.

Figure 2.1.h. AXIS 212 PTZ Network Camera
PTZ dome network cameras
PTZ dome network cameras can cover a wide area by enabling greater flexibility in pan, tilt and zoom
functions. They enable a 360-degree, continuous pan, and a tilt of usually 180 degrees. PTZ dome
cameras are ideal for use in discreet installations due to their design, mounting (particularly in drop-
ceiling mounts as seen in the picture to the right), and difficulty in seeing the cameras viewing angle
(dome coverings can be clear or smoked). A PTZ dome network camera also provides mechanical ro-
bustness for continuous operation in guard tour mode, whereby the camera continuously moves be-
tween presets. In guard tour mode, one PTZ dome network camera can cover an area where 10 fixed
cameras would be needed. The main drawback is that only one location can be monitored at any
given time, leaving the other nine positions unmonitored. The optical zoom typically ranges between
10X and 35X. A network dome camera is often used in situations where an operator is employed. This
type of camera is usually mounted on a ceiling if used indoors, or on a pole or corner of a building in
outdoor installations. With a PTZ dome network camera, all PTZ control commands are sent over an
IP network, and no RS-485 wires need to be installed, unlike the case with an analog dome camera.
Figure 2.1.i. AXIS 233D Network Dome Camera in drop-ceiling mount
13
b) Feature considerations
> Image sensor: Two types of image sensor technologies are available for use in network cameras:
CCD (charge-coupled device) and CMOS (complementary metal-oxide semiconductor). Each has
its own unique strengths and weaknesses that make them appropriate for different applications.
CCD sensors have been used in cameras for more than 20 years and present many advantageous
qualities such as good light sensitivity, which is important in low-light conditions. However, they
are more expensive and more complex to incorporate into a camera and may consume much more
power than an equivalent CMOS sensor.







Figure 2.1.j. CCD Figure 2.1.k. CMOS
Recent advances in CMOS sensors bring them closer to their CCD counterparts in terms of image
quality. CMOS sensors lower the total cost for cameras since they contain all the logics needed to
build cameras around them. CMOS sensors enable more integration possibilities and more
functions. They make it possible for manufacturers to produce smaller-sized cameras.
The most common image sensor sizes used in network cameras are -inch and 1/3-inch and they
may use progressive scan or interlaced scan technology (see next point below for more on the
technologies). Many megapixel sensors are the same size as sensors used in cameras that deliver
VGA 640x480 resolution. It means that the megapixel sensor has many more pixels but the pixel
sizes are smaller, and therefore, less light sensitive than a non-megapixel sensor.
> Progressive scan: This technology involves exposing, capturing and presenting an entire image at
one timeline by line in perfect order, rather than splitting an image into two separate fields and
presenting them at separate times as with analog interlaced scanning technology. Since PC
monitors use progressive scan technology, moving objects in a video will be presented more clearly
on PC screens if the video is captured using progressive scan. If interlaced video is presented on a
PC screen, objects that move between the image capture of two interlaced fields will be blurry. All
of Axis current network cameras, with the exception of a couple of PTZ dome cameras, use progres-
sive scan technology.

Progressive scan An interlaced scan image shown on a progressive PC monitor







Figure 2.1.l.
Freeze frame on moving
dot using progressive scan
Figure 2.1.m.
1st field: Odd lines 2nd field: Even lines
[17/20 ms (NTSC/PAL) later]
Freeze frame on moving
dot using interlaced scan
14
> Lens: Different types of lens are available on network cameras. Lenses may be fixed (the focal
length or horizontal field of view is fixed), varifocal (allows for the manual adjustment of the focal
length) or zoom (allows the camera to stay in focus when zooming in on objects). Varifocal and
zoom lenses offer focal lengths that range from telephoto to wide angle.
Figure 2.1.n. Fixed lens Figure 2.1.o. Varifocal lens
A lens iris, which controls the amount of light coming into the camera, can be manually adjusted
(for indoor cameras) or automatically controlled (for outdoor cameras). An auto iris lens can be
controlled by the cameras processor (DC-controlled), or by video signal.
> Lens changeable: Changeable lens gives users the option of using other lenses (such as telephoto
or wide angle) that may be more appropriate for a particular application. You will need to know if
the cameras original lens is C-mount or CS-mount so that the new lens you purchase fits the same
type of mount. Today, almost all surveillance cameras and lenses sold are CS-mount types.
When choosing the size of a new lens, you will also need to know the size of the image sensor. If a
lens is made for a smaller sensor than the one actually fitted inside the camera, you will have black
corners in the image. If a lens is made for a larger sensor than the one fitted inside the camera, the
angle of view will be smaller than the default angle of the lens since part of the information will be
lost outside of the sensor.
> Automatic day/night functionality: This feature is incorporated into some outdoor cameras and
enables the automatic removal of the infrared (IR) cut filter that is incorporated into all color
cameras to prevent color distortion from near-infrared light. When there is light, the IR-cut filter
is on and the camera delivers color video. In dark conditions, the camera removes the filter to make
use of near-infrared light to deliver infrared-sensitive black and white video. Infrared or day/night
cameras are particularly useful in outdoor environments or situations that restrict the use of arti-
ficial light. These situations include discreet and covert surveillance applications.
> Minimum illumination/light sensitivity: A network
cameras light sensitivity is often specified in terms of
lux, which corresponds to a level of illuminance in which
a camera produces an acceptable image. The lower the
lux number, the better the camera is at capturing images
in low light conditions. If a camera is specified to work
down to 1 lux, it means that the camera can produce an
image at 1 lux, but it may not necessarily be of high
quality. Normally, at least 200 lux is needed to illuminate
an object so that a good quality image can be obtained.
Different manufacturers also use different references
when they specify the lightsensitivity of a camera, so it
is important to look at captured images to make a com-
parison.
Environment: lux
> Strong sunlight: 100,000
> Full daylight: 10,000
> Normal office light: 500
> Poorly lit room: 100
Lux is the amount of light falling onto a
surface per square meter. Many natural
scenes have fairly complex illumination
with both shadows and highlights that
give different lux readings in different
parts of a scene. It is, therefore, impor-
tant to keep in mind that one lux read-
ing cannot be an indication of the light
condition for a scene as a whole.
15
> Type of video compression: There are three main video compression standards in use today:
Motion JPEG, MPEG-4 Part 2 (also referred to simply as MPEG-4 in some references), and H.264
(also known as MPEG-4 Part 10/AVC). Each standard employs different techniques to reduce the
amount of data transferred and stored in a network video system.
H.264 is the latest standard that is expected to become the video standard of choice in the
coming years. Without compromising image quality, H.264 can reduce bandwidth and storage
requirements by more than 80 percent compared with Motion JPEG and as much as 50 percent
more than with the MPEG-4 Part 2 standard. H.264 and MPEG-4 Part 2 are licensed technologies,
so if a network video product supports those standards, be sure to find out if the license fee is
already included in the products purchase price. H.264 and MPEG-4 Part 2 provide support for
synchronized audio, while Motion JPEG does not. Motion JPEG is an unlicensed technology.
For the time being, network video products that support multiple compression standards are ideal
for maximum flexibility and integration possibilities.
> Video resolution: A VGA resolution is 640x480 pixels. (Computer screens have resolutions in VGA
or multiples of VGA.) Another common format is 4CIF (704x480 pixels in NTSC / 704x576 pixels in
PAL standard). Megapixel cameras provide high resolutions of at least 1280x960 pixels and are
used for applications that require the ability to see fine details or cover a large area. A network
video products ability to deliver a specified number of frames per second may vary depending
on the resolution.
> Frames per second: There may be different frame rates specified for different resolutions. Full-
motion video is 30 frames per second in NTSC video standard (in North America/Japan) and 25
frames per second in PAL video standard (Europe). Full frame rate on all cameras at all times is
more than what is required for most applications. With the configuration capabilities and built-in
intelligence of network cameras, frame rates under normal conditions can be set lower, e.g. one to
four frames per second, to dramatically decrease storage requirements. In the event of an alarm
for instance, if video motion detection or an external sensor is triggereda video management
software program can be configured to request that the network video product send a different
stream with a higher recording frame rate.
> Multiple, individually configurable streams: Network video products with this capability can
provide multiple streams and each stream can be configured differently in terms of compression
format and level, frame rate and resolution. For example, one stream can be configured with
maximum compression and low frame rate for storage purposes; another stream can be sent with
higher frame rate and less compression and, therefore, less lag for live viewing; and a third stream
with high compression and low resolution can be sent to mobile devices.
Figure 2.1.p. Multiple, individually configurable video streams
Local recording/
viewing at full
frame rate and
high resolution
Remote recording/
viewing at medium
frame rate and
medium resolution
1 second
Viewing with a
mobile telephone
at medium frame
rate and low
resolution
AUDIO I/O
IN OUT 1 2 3 4 5 6
Analog camera
Video encoder
16
> Audio support: A network camera with audio support comes either with a built-in microphone or
an input for an external microphone. Speakers may be built in or external. An audio feature
enables users to remotely listen in on an area and communicate instructions, orders or requests to
visitors or intruders. Audio can also be used as an independent detection method. When sound
above a certain level is detected, video recordings and alarms can be triggered.
Figure 2.1.q. Enhancing video surveillance with audio
Audio modes may be simplex (audio is sent either by the operator or the camera), half duplex
(audio is sent in both directions, but only one party at a time can send) or full duplex (audio is sent
to and from the operator simultaneously). Audio can be compressed and integrated into the video
stream, and sent over a network for monitoring and/or recording. There are four audio compres-
sion standards used in network video. They are AAC-LC, which requires a license, and G.711, G.726
and G.722.2 (Adaptive Multi-RateWideband), which are non-licensed technologies. Audio and
video are two separate packet streams that are sent over a network. In order for the client or
player to perfectly synchronize the audio and video streams, the audio and video packets must be
time-stamped. Time stamping using Motion JPEG may not always be supported in a network
camera. If synchronized audio and video is a priority, it is better to use H.264 or MPEG-4 Part 2
for the video compression since time stamping is usually supported using those standards.
> Input and output (I/O) ports: Input/output connectors enable external devices to be connected
to a network camera. Inputs to a camera (e.g. a door contact, infrared motion detector, glass break
sensor or shock sensor) enable the camera to react to an external event by, for example, initiating
the sending and recording of video. Outputs enable the camera to control external devices such as
activating alarms, triggering door locks, generating smoke or turning on lights.
I/Os also allow you to save storage space. For example, if you want to simply capture the identity
of a person at an entrance, you do not need the camera to continually send video. You can set up
the system in such a way that the camera is triggered to capture and send the necessary image
frames only when the door opens. I/O ports are available in all Axis network cameras and video
encoders.
> Video motion detection: Video motion detection monitors changes in the cameras field of view
and if a change occurs (e.g. an intruder enters the scene), an alarm condition is generated. This
function can be a built-in feature of a network camera or a feature of a video management soft-
ware. Using the built-in video motion detection feature in a network camera reduces bandwidth
use since no video is delivered on the network unless video motion is detected. Video motion
detection is a standard feature in all Axis network cameras.
> Active tampering alarm: This is an intelligent video analytics application available in selected
Axis network video products. When a camera is manipulated in any way (e.g. accidental redirec-
tion, blocking, defocusing spray-painted, covered or damaged), it can automatically trigger
recordings and alert notifications.
Axis network
camera
Power over Ethernet-
enabled network switch
Computer
Microphone
Microphone
Loudspeaker
Loudspeaker
17
> Alarm and event management: With this capability, event triggers can be programmed based on
schedule, I/Os, video motion detection, audio detection, active tampering alarm or temperature,
among others. Pre- and post-alarm image buffers within a network camera can save and send
images collected before and after an alarm occurs. Once an alarm or event is detected, a network
camera can send notifications via e-mail, TCP, HTTP and upload images via e-mail, FTP and HTTP.
Note that image uploads consist of sending individual JPEG files and do not mean recordings of
video streams. Recording a video stream on an alarm trigger can be done using a video manage-
ment software program, which has the capability to request a stream based on specific criteria
(e.g., an H.264, MPEG-4 or Motion JPEG compression format, higher frame rate and image quality)
that may be different from normal recording settings.
> Power over Ethernet (PoE) (IEEE 802.3af): When a network camera supports this feature, it
means that the camera can receive power through the same cable as for data. It reduces cabling
requirements and installation costs.
> Wireless: A network camera with built-in wireless support is a consideration when running a cable
between a LAN and a network camera is impractical, difficult or expensive. Wireless network
cameras are suitable for use in outdoor situations, in environments such as historic buildings where
the installation of cables would damage the interior, or in cases where there is a need to move
cameras to new locations on a regular basis, such as in a supermarket. Ensure that the wireless
network camera supports security protocols such as IEEE 802.1X and WPA/WPA2 (Wi-Fi Protected
Access), which will help secure the wireless communication.
> Security and management: At a basic level, a video surveillance network camera should provide
different levels of password-protected access to a network camera. For instance, some authorized
users may only have access to view images from specific cameras; others have operator-level access,
and a few have access to administer all settings in a network camera. Beyond multi-level password
protection, a network camera may offer HTTPS encryption for secure communication; IP address
filtering, which gives or denies access rights to defined IP addresses; IEEE 802.1X to control network
access; and user access log.
> Network management features: They include support for Quality of Service (QoS), which can
prioritize and reserve network capacity for mission-critical surveillance in a QoS aware network,
and support for Internet Protocol version 6 (IPv6) in addition to IPv4 addresses.
c) How to select a network camera:
To determine the type of network cameras required, as well as the number of cameras needed to
adequately cover an area, you first need to determine the scene or environment and the goal of the
surveillance application.
Consider:
1) Environment: This will determine whether you need an outdoor or indoor camera, whether the
camera needs to be tamper or vandal proof, and whether special housing is required. Consider also
the lighting requirements: Is there adequate light to obtain a good quality image? Do you need to
add light sources? How light sensitive should the camera be?

Figure 2.1.r. Overview Figure 2.1.s. Close-up
18
2) Area of coverage: A PTZ or dome camera is able to cover a wider area than a fixed network
camera. The bigger the area, the more cameras are needed.
3) Application:
i. Determine the kind of surveillance you want to conduct (overt/covertthis will help you in
selecting cameras that offer a non-discreet or discreet installation).
ii. Determine also the kind of image you want to capture: overview or close-up for identifica-
tion purposes. The purpose will determine the placement of the camera, the type of camera
and camera features required (e.g. megapixel for exceptional details, audio, security
features) and lens adjustment/type (normal, telephoto or wide angle).
A security operator using a PTZ or dome camera can cover a large area and capture different
images for different purposes. In many cases, different cameras will be needed to capture
images for different purposes (i.e. one camera providing a full overview image for capturing
an incident in action, and another camera for close-up views of a person/object for identifi-
cation purposes).
iii. Viewing and recording needs: Consider when and how often you need to view and record:
day, night and/or weekends; frame rate capabilities; resolution; type of video compression
support (H.264/MPEG-4 Part 2/Motion JPEG) and different alarm management functions
and intelligent video features such as video motion detection, active tampering alarm
and audio detection, which are also features that provide savings in bandwidth and storage
space.
iv. Connection considerations: e.g. Power over Ethernet support, wireless.
Focus on image quality, open API, free upgrades, global product support
Axis network video products are focused on providing high image quality. The products also have an
open API (application programming interface) that enables many software vendors to write programs
for. This benefit increases your choices in software applications. Axis also continually supports its net-
work video products with free upgrades for new functionalities that are introduced. Global product
support is also available.
In addition to network cameras, Axis offers video encoders and decoders, network video recorders and
video management software. A wide range of accessories are also available: protective housings, IR il-
luminators, Power over Ethernet midspans and active splitter, connectors and cables, lenses and lens
accessories, power accessories, as well as third-party accessories.
Before you set out to order or buy many network cameras, it is a good idea to field test a few cameras
before making a decision. Try out an Axis network camera with a free AXIS Camera Station One video
management software, which is packaged with every network camera purchase and is also downloadable
on Axis web site at www.axis.com. AXIS Camera Station One provides simultaneous viewing and recording
of high quality H.264, MPEG-4 Part 2 and Motion JPEG video from a single surveillance camera.
19
Video encoder
If you already have existing analog CCTV surveillance cameras and want to move to an IP-based surveil-
lance system, you can still make use of your analog investments by adding a video encoder (also called
a video server). Simply connect a video encoder to analog cameras. The encoder converts analog signals
into digital video and sends them over an IP network, enabling users to remotely monitor the cameras,
as well as record and store video on standard PC servers. A video encoder brings new functionalities and
benefits, such as remote monitoring capabilities, event management, scalability and ease of integration
with other security systems. It also eliminates the need for dedicated equipment such as coaxial cabling,
analog monitors and digital video recorders.
Figure 2.2.a. A video encoder migrates analog cameras into an IP-based video solution
Figure 2.2.b. A one-channel, standalone video encoder with audio, I/O (input/output) ports for controlling external devices such
as sensors and alarms, serial ports (RS-422/485) for controlling PTZ analog cameras and Ethernet connection with Power over
Ethernet support.
A video encoder can be connected to a wide variety of specialized cameras, such as a highly sensitive
black and white camera, a miniature or a microscope camera, in addition to fixed, dome, indoor, outdoor
and pan/tilt/zoom analog cameras.
A standalone video encoder typically provides between one and four connections to analog cameras, as
well as an Ethernet port to connect to the network. Like network cameras, it contains a built-in web
server, a compression chip, an operating system and processing power for local intelligence.
Besides digitizing analog signals, a video encoder can support a host of other functions: for example, in-
telligent video functionalities such as video motion detection, active tampering alarm and audio detec-
tion; digital inputs and outputs (I/O, which can trigger the encoder to start sending images or to activate
alarms and devices such as lights and doors); and serial port(s) for serial data or control of pan/tilt/zoom
cameras and devices. With image buffering, a video encoder can also send pre- and post-alarm images.
Some Axis video encoders also support Power over Ethernet (PoE), which enables the video encoders, as
well as the analog cameras that are connected to them, to receive power through the same cable as for
data transmission. Installation is easier and costs are reduced since there is no need to run separate
cables for power. It also makes it easier to move a camera/video encoder to a new location. With PoE, a
camera/video encoder can still operate in the event of a power failure if it is connected to a centralized
backup power with an Uninterruptible Power Supply.
2.2.
Network switch
Computer with
video management
software
LAN LAN/Internet
Axis video
encoder
AUDIO
I/O
IN
OUT 1 2 3 4 5 6
Analog Coax
Cabling
Analog
cameras
Audio
I/O
RS-422 RS-485
Analog input
Power
Ethernet (PoE)
20

Figure 2.2.c. When the AXIS Q7900 Rack is fully outfitted with 6-channel video encoder blades, it can accommodate 84 analog
cameras.
In instances where there are large numbers of analog cameras with coaxial cables running to a dedi-
cated control room, rack-mounted video encoders or blades (video encoders without their casings) are
beneficial. A rack can be outfitted with a mix of video encoder blades. Video encoder blades with one,
four and six channels are available from Axis. Racks come with network, serial and I/O ports, and may
provide a common power supply to all the blades. Axis racks also enable hot swapping of the video en-
coder blades so there is no need to power down when installing or removing the blades. One 19-inch
rack can digitize up to 84 analog cameras and send multiple streams from each channel.
Where no coaxial cabling is in place, it is always best to use standalone video encoders and position
them close to the analog cameras. It eliminates the need to lay new, separate coaxial cables since video
and PTZ commands can be sent over an IP network infrastructure. This reduces installation costs and
also eliminates the loss in image quality that would occur if video were to be transferred over long dis-
tances through coaxial cables. With coaxial cables, the video quality decreases the further the signals
have to travel. Digital images do not lose quality over distance.
Considerations when selecting a video encoder solution:
(See also guidance provided in the previous section under network cameras.)
> Image quality: Axis video encoders provide high-quality, deinterlaced digital video. The deinterlace
filter eliminates the artifacts (a series of horizontal lines) caused by analog interlaced scanning tech-
nology.
> Frame rate and resolution: Axis high performance video encoders provide full frame rate30 fps
(frames per second) in NTSC, 25 fps in PALin all resolutions for all video channels. Common
resolutions are: CIF (352x240 NTSC, 352x288 PAL), 4CIF (704x480 NTSC, 704x576 PAL), and D1
(702x480 NTSC, 720x576 PAL), which is the highest available resolution.
> Video compression: Many Axis video encoders offer users the option of more than one video
compression format. The video compression standards include Motion JPEG, MPEG-4 and H.264.
H.264 is the latest compression standard that offers the most efficient format for compressing video
and which enables great savings in bandwidth and storage.
> Multiple, individually configurable streams: The Axis video encoders that have this capability are
able to provide multiple streams from each video channel. Each stream can be configured differently
in terms of compression format and level, frame rate and resolution.
> Power over Ethernet: Some Axis video encoders have built-in support for PoE. Consider if there is a
need for PoE, which reduces costs and makes installation easier.
> Audio: A microphone or line-in equipment can be connected to Axis video encoders with integrated
audio. Audio enhances the video surveillance capability by enabling users to also listen in on an area
or pick up unusual sounds. Audio detection can also be used as an event trigger.
> Rack solution: Consider if there is a need for a rack solution, the number of analog channels a rack
can support, as well as the types of network connection supported.
21
> Event management and intelligent video: Consider requirements for I/Os and intelligent video
functionalities such as video motion detection, audio detection and active tampering alarm. These
features can help reduce bandwidth and storage consumption as they enable only actionable data to
be sent upon alarm.
> Advanced security and network management: Axis video encoders offer many ways to secure
access to video. Security features include multi-level password protection; IP address filtering, which
gives or denies access rights to defined IP addresses; HTTPS encryption, which provides a secure
channel between the video encoder and application; and IEEE 802.1X to control network access. Net
work management features include Quality of Service (QoS), which helps secure the necessary band
width for streaming video and control commands over a network; and support for Internet Protocol
version 6 (IPv6) and standard IPv4 addresses.
> Video management software: Axis video encoders are supported by a wide range of application
software, including AXIS Camera Station.
Network
The next consideration to make is assessing your network needs.
Network switches allow devices such as network cameras, servers and PCs to communi-
cate with each other to share information and, in some cases, a common Internet con-
nection. Network designs can take many forms and may vary in terms of performance
and security.
First, determine what your company is using the network for and how congested your
local area network (LAN) or wide area network (WAN) is.
If you are implementing a smaller surveillance system involving 8 to 10 cameras, you
should be able to use a basic 100-megabit (Mbit) network switch without having to
consider bandwidth limitations. Most companies can implement a surveillance system of
this size using their existing network.
If you are implementing 10 cameras or more, you should try to estimate the load on the network using
a few rules of thumb:
> A camera will use approx. 2 to 3 megabits of bandwidth when configured to deliver high-quality
images at high frame rates.
> With more than 12 to 15 cameras, you should consider using a switch with a gigabit (Gbit) backbone.
If a gigabit-supporting switch is used, the server that runs the video management software should
have a gigabit network adapter installed.
Determine the pattern of congestion levels over a given period to find out if you have to install addi-
tional bandwidth capacity on your network or whether you can make use of the same network as for
general business activities. It may be that the network traffic drops off during nighttime and weekends
the times when you may want to activate the video surveillance system. The usage pattern will help you
to determine whether you can a) simply use the same network infrastructure for your general purpose
needs as for your surveillance needs, or b) use a combination of existing general purpose network as well
as a new network for IP-Surveillance. If additional network capacity is needed, new cabling is normally
not needed since adding a switch or reconfiguring the patch panel may solve the problem. One tool that
helps estimate bandwidth usage is the AXIS Design Tool, which is available at www.axis.com/products/
video/design_tool/. See also section 5.d for more about bandwidth control.

2.3.
22
Wireless networks
When running a cable between a LAN and a network camera is impractical, difficult or expensive, a
wireless solution using a wireless access pointalso called a device bridge or wireless routeris a good
option. Wireless technology can be useful, for example, in historic buildings where the installation of
cables would damage the interior; within facilities where there is a need to move cameras to new loca-
tions on a regular basis, such as in a supermarket; or in outdoor installations. Wireless technology can
also be used to bridge sites without expensive ground cabling.
Figure 2.3.b. A network with wired and wireless connections.
Security in wireless networks
Securing a wireless network should be addressed. Otherwise, everyone with a wireless device present
within the area covered by the network will be able to participate in the network and use shared ser-
vices. The most commonly used standard today is WEP (Wireless Equivalent Privacy), which adds RSA
RC4-based encryption to the communication, and prevents people without the correct key from access-
ing the network. But as the key itself is not encrypted, it is possible to pick the lock, so this should be
seen only as a basic level of security. A new standard, the WPA (WiFi Protected Access), significantly
increases security by taking care of some of the shortcomings in the WEP standard with, for instance,
the addition of an encrypted key.
When using wireless cameras for surveillance, there are a few rules of thumb:
> Enable the user/password login in the cameras
> Enable the encryption in the wireless router/cameras
> Since wireless routers do not have the same bandwidth capacity as a normal switch, no more than
four to five cameras should be connected to a wireless access point.
Hardware (storage needs)
Similar to the way a PC can save documents and other files, video can be stored on a server or PC hard
disk. Specialized equipment is not needed since a storage solution treats video data like any other large
group of files that can be stored, accessed and eventually deleted. Video storage, however, puts new
strains on storage hardware because it may be required to operate on a continual basis, as opposed to
during normal business hours with other types of files. In addition, video by nature generates very large
amounts of data, creating high demands on the storage solution.
Calculating the storage needs
In order to appropriately calculate the storage requirements of a network surveillance system, there are
a number of elements to factor in, such as the number of cameras required in your installation, the num-
ber of hours a day each camera will be recording, how long the data will be stored, and whether the
system uses event triggers such as video motion detection or continuous recording. Additional param-
eters such as frame rate, compression, image quality and scene complexity (little motion or lots of mo-
tion) should also be considered.
Wireless device
point
Axis network
camera
Axis network
camera
Wireless access
point
Axis network
camera
Server
Network switch
PC client
2.4.
23
The type of video compression employed also effects storage calculations. The H.264 compression for-
mat is by far the most efficient video compression technique available today. Without compromising
image quality, an H.264 encoder can reduce the size of a digital video file by more than 80 percent
compared with the Motion JPEG format and as much as 50 percent more than with the MPEG-4 Part 2
(referred to simply as MPEG-4 in future references) standard. This means much less network bandwidth
and storage space are required for an H.264 video file. Or seen another way, much higher video quality
can be achieved for a given bit rate.
With Motion JPEG, storage requirements vary depending on the frame rate, resolution and degree of
compression. With H.264 and MPEG-4, bit rate is the key factor in determining the corresponding stor-
age requirements.
There is a clear formula for calculating storage requirements when it comes to Motion JPEG (see calcula-
tion below) because Motion JPEG consists of one individual file for each image. Calculations are not so
clear-cut for H.264 and MPEG-4 because of a number of variables that affect bit rate levels. However,
sample calculations for H.264 and MPEG-4 are also provided below:
H.264 calculation:
Bit rate / 8(bits in a byte) x 3600s = Kilobyte (KB) per hour / 1000 = Megabyte (MB) per hour
MB per hour x hours of operation per day / 1000 = Gigabyte (GB) per day
GB per day x requested period of storage = Storage need
(Note: The figures below are based on lots of motion in a scene. With fewer changes in a scene, the figures can be 20 percent lower.
The amount of motion in a scene can have a big impact on the amount of storage required.)
Total for the 3 cameras and 30 days of storage = 135 GB
MPEG-4 calculation:
Bit rate / 8(bits in a byte) x 3600s = KB per hour / 1000 = MB per hour
MB per hour x hours of operation per day / 1000 = GB per day
GB per day x requested period of storage = Storage need
(Note: The formula does not take into account the amount of motion, which is an important factor that can influence the size of
storage required.)
Total for the 3 cameras and 30 days of storage = 204 GB
Motion JPEG calculation:
Image size x frames per second x 3600s = KB per hour/1000 = MB per hour
MB per hour x hours of operation per day / 1000 = GB per day
GB per day x requested period of storage = Storage need
Total for the 3 cameras and 30 days of storage = 1002 GB
Camera Resolution
Bit rate
(Kbit/s)
Frames per
second
MB/hour
Hours of
operation
GB/day
No. 1 CIF 110 5 49.5 8 0.4
No. 2 CIF 250 15 112.5 8 0.9
No. 3 4CIF 600 15 270 12 3.2
Camera Resolution
Bit rate
(Kbit/s)
Frames per
second
MB/hour
Hours of
operation
GB/day
No. 1 CIF 170 5 76.5 8 0.6
No. 2 CIF 400 15 180 8 1.4
No. 3 4CIF 880 15 396 12 5
Camera Resolution Image size (KB)
Frames per
second
MB/hour
Hours of
operation
GB/day
No. 1 CIF 13 5 234 8 1.9
No. 2 CIF 13 15 702 8 5.6
No. 3 4CIF 40 15 2160 12 26
24
Storage Options
Storage solutions depend on a PCs or servers ability to store data. As larger hard drives are produced at
lower costs, it is becoming less expensive to store video. There are two ways to approach hard disk stor-
age. One is to store video on the same server that runs the application. This is called a direct attached
storage. The other is to have the storage separate from the server that runs the application. This is called
a network-attached storage (NAS) or a storage area network (SAN).
Figure 2.4.a. Direct attached storage
Direct attached storage is probably the most common solution for hard disk storage in small to medium-
sized IP-Surveillance installations (See image above). The hard disk is located in the same PC server that
runs the video management software. The PC and the number of hard disks it can hold determine the
amount of storage space available. Most standard PCs can hold between two and four hard disks. With
todays technology, each disk can store approximately 300 gigabytes of information for a total capacity
of approximately 1.2 terabytes (one thousand gigabytes).
For information about NAS and SAN, please see Chapter 8.
Video management software
Although video can be managed simply by using the built-in web interface of a network video product,
video management software enables more effective management of video from multiple cameras for live
monitoring and recording. Video management software is, therefore, an important component of an IP-
Surveillance system.
Video management requirements depend on the number of cameras, performance criteria, platform
preferences, scalability, and whether there is a need for integration with other systems. Solutions typi-
cally range from single PC systems to advanced client/server-based software that provides support for
multiple, simultaneous users and thousands of cameras.
AXIS Camera Station
AXIS Camera Station is a video management software program that is designed specifically for manag-
ing Axis network cameras and video encoders. It enables multi-camera viewing, high-quality recording,
playback and event management.
Figure 2.5.a. AXIS Camera Station video management software
2.5.
Computer server with video
management software
Network switch
Network cameras
25
Key features include:
> Simultaneous viewing and recording of live video from multiple cameras: Multiple users can view
several different cameras at the same time, and recordings can take place simultaneously. The system
can also be used for different purposes; for example, in a retail environment, one user can use the
system for security, while another individual may use the same system to study store traffic.
> Several recording modes: Continuous, on alarm trigger and/or intelligent video features such as
video motion detection, and manually. Continuous and triggered recordings can be scheduled to run
at selected times during each day of the week. The software supports recordings in H.264, MPEG-4
and Motion JPEG for optimized quality and bandwidth. For a comprehensive picture of an event, the
softwares multi-view playback feature allows users to view simultaneous recordings from different
cameras. Recording instances can be visualized using a timeline, making searches easy. Recordings
can also be searched based on motion and external alarm triggers. Export functionality is also
provided.
> Alarm management functions: Event triggers can be programmed based on schedule, I/Os and
intelligent video functionalities such as video motion detection. AXIS Camera Station can set the
amount of pre- and post-alarm image buffers a network camera or video encoder should send before
and after an alarm occurs. Once an alarm or event is detected, the software program can send alarm
notifications via e-mail and request that a network video product send a video stream with specific
settings for recording.
> Frame rate control: AXIS Camera Station enables users to set different recording frame rates for
selected cameras; for example, one under normal operation and another when alarm is triggered.
Different frame rates can also be set for viewing and/or recording purposes and for different
recipients.
> Camera management: AXIS Camera Station enables administration and management of network
cameras and video encoders to be done from a single interface. It is useful for tasks such as detecting
cameras on the network, managing IP addresses, and setting resolution, compression and security
levels. The software can provide access to every camera on the network and will automatically
administer firmware upgrades. This is practical particularly in situations where cameras are located in
distant or hard-to-reach locations. The administrator does not have to visit each location to upgrade
every camera.
Each AXIS Camera Station installation lets you monitor up to 50 cameras at the same time. You can
install as many AXIS Camera Station programs as required. Based on a PC Server platform solution, the
software enables full scalability as cameras can be added one at a time and there is no limit to the num-
ber of cameras that can be added or managed. The limitation is only in the storage hardware capacity
rather than the software. Since AXIS Camera Station uses common, off-the-shelf hardware, the hard-
ware components can be selected for maximum performance.

Recordings are saved directly onto the hard disk(s) of the local PC server where the AXIS Camera Station
is installed. A Windows-based software, AXIS Camera Station has a Windows client program that is used
to provide local or remote viewing, playback and administration. All settings are inherited and down-
loaded from the video management software. This means that the server can be placed anywhere; for
example, in the server room or basement.
26
Figure 2.5.b. AXIS Camera Station is installed on a Windows-based PC. Remote users can access the software via a Windows client.
The AXIS Camera Station Client enables users to switch between different servers with the video man-
agement software installed. This makes it possible to manage video at many remote sites or in a large
system. AXIS Camera Station runs as a background service on a Windows PC with XP Professional or
Vista Business. This means that even when you are logged off the PC that is running the software, the
AXIS Camera Station program is still operating.
AXIS Camera Station can also be integrated with other systems such as point of sale, access control,
tracking (e.g. radio-frequency identification), building management and industrial control. When video
is integrated, information from other systems can be used to trigger functions such as event-based re-
cordings in the network video system, and vice versa. In addition, users can benefit from having a com-
mon interface for managing different systems.
AXIS Camera Station comes with a base license for four Axis network cameras/video encoders. The
number of licenses required is based on the number of network cameras/video encoders that are to be
used with the program. Additional licenses, as well as software upgrade licenses, are available for pur-
chase at your local Axis reseller.
More details about AXIS Camera Station are covered in the latter half of this document.

AXIS Camera Station
Client software
OPTIONAL VIEWING,
PLAYBACK and
ADMINISTRATION
Axis network cameras
Analog cameras
Network
switch
AUDIO
I/O
IN
OUT 1 2 3 4 5 6
Axis video encoder
VIEWING, PLAYBACK
and ADMINISTRATION
BACKGROUND
SERVICE
RECORDING
DATABASE
OPTIONAL VIEWING,
PLAYBACK and
ADMINISTRATION
Remote access via
AXIS Camera Station
Client software
AXIS Camera Station
software installed on a
Windows PC
Broadband
router
INTERNET
IP NETWORK
Coax
cables
27
Mounting surveillance cameras
This chapter provides recommendations on how to best achieve useable, high-quality, surveillance video
based on camera positioning and environmental considerations.
The following are some guidelines:
> Surveillance objective
When positioning a surveillance camera, it is important to keep in mind the kind of
image you would like to capture. If the aim is to get an overview of an area to be able
to track the movement of people or objects, make sure you are using a suitable camera
and that it is placed in a position that achieves this goal.
If the intention is to be able to identify a person or object, you will need a suitable
camera that is positioned or focused in a way that will capture the level of detail
needed for identification purposes. It may be favorable to place a camera in a high
position to limit tampering. However, a lower placement may improve identification of
faces or detailed objects, avoiding a birds eye perspective. Local police authorities
may also be able to provide guidelines on how best to position a surveillance camera.
A letter chart, with varying letter sizes (attached as an appendix in this document), can
be used as an indicator of the level of detail an installed camera can provide. A
spinning Rotakin (see device at right) may also be used to test how well a camera
displays moving objects.
> Housing
If a camera is to be mounted outdoors or in a relatively hostile environment, it needs a protective
(weatherproof and/or vandal-proof) housing. Camera housings come in different sizes and qualities
and some versions have built-in fans (for cooling) and/or heaters. There are vandal-resistant cameras
that are already designed with an IP66-rated casing and have a built-in heater and fan, such as the
AXIS 225FD Network Camera. In such a case, no additional housing accessory is required.



Figure 3.b. Outdoor casing suitable for use with Axis network cameras.
> Reflections
If a camera is mounted behind a glass in a housing, the lens must be placed close to the glass.
Otherwise, reflections from the camera and the background will appear in the image. To reduce
reflection, special coatings can be applied on any glass used in front of the lens.

Figure 3.c. How to position a camera to avoid reflections.
3.
R
e
f
le
c
t
io
n
R
e
f
le
c
t
io
n
Glass
BAD
Glass
GOOD
28
> Secure support
A camera should be placed on stable supports to minimize camera movement. As PTZ cameras move
around, the action can cause image interference if the camera mounting is not properly secured. In
outdoor situations, sturdy mounting equipment should always be used to avoid vibrations caused by
strong winds.
> Use lots of light/Add light if needed
The most common reason for poor quality images is lack of
light. Generally, the more light, the better the images. With
too little light, the images will become blurred and dull in
color. You can easily and cost-effectively add strong lamps in
both indoor and outdoor situations to give you the light
conditions necessary for capturing good images.
Lux is the standard unit of measurement for light. The table at right shows the available light in
different kinds of conditions. At least 200 lux is needed to capture good quality images. A high-
quality camera might be specified to work down to 1 lux, which means that you can capture an image
at 1 lux, but it may not be of high quality. Different manufacturers use different references when they
specify the light sensitivity of a camera, and this makes it difficult to compare cameras without first
testing them and comparing the images captured.
When using external, artificial lighting in outdoor environments, reflections and/or shadows should
be avoided.
For covert security or in areas where the presence of artificial light is unwanted, you can choose to
use an IR-sensitive, black and white camera, or an automatic, day/night camera. In a day/night
camera, color video is delivered during light conditions, while at night, the camera makes use of
near-infrared light to generate IR-sensitive, black and white video. An IR illuminator, which provides
infrared light, can also be used in conjunction with an IR-camera or a day/night camera to further
enhance a cameras ability to produce high-quality video in low-light or nighttime conditions.
Figure 3.d. IR-sensitive network camera with IR illuminator attached below the camera housing
Environment: lux
> Strong sunlight: 100,000
> Full daylight: 10,000
> Normal office light: 500
> Poorly lit room: 100
29
> Avoid direct sunlight
Direct sunlight should always be avoided. Direct sunlight will blind the camera and can reduce the
performance of the image sensor chip. If possible, position the camera with the sun shining from
behind the camera.
> Bright areas in the images should be avoided as they might become overexposed (bright white) and
objects can then appear too dark. This problem typically occurs when attempting to capture an object
in front of a window. To solve this problem, simply reposition the camera or draw the curtains and
close blinds if possible.

> Contrast
In outdoor environments, viewing too much of the sky results in too much contrast. The camera will
adjust in order to achieve a proper light level for the sky. Consequently, the object/landscape of
interest will appear too dark. One way to solve this problem is to mount the camera high above the
ground, using a pole if needed. In advanced network cameras, users may be able to set which part of
an image should be more correctly exposed.
> Lenses
An auto iris lens should always be used for outdoor applications. An auto iris lens automatically
adjusts the amount of light that reaches the image sensor. This optimizes the image quality and
protects the image sensor from being damaged by strong sunlight.
Figure 3.e. Avoid very bright areas in an image
by changing the camera position.
Figure 3.f. Advanced cameras include
the feature to compensate for backlight.
30
> Adjust camera settings
It is important to adjust the white balance settings for different environments (indoor/outdoor/
fluorescent), as well as for brightness and sharpness.

Figure 3.g. Example of a camera user interface showing options for advanced camera settings.
When deciding upon the exposure, a fast shutter speed or shorter exposure time is recommended when
capturing rapid movement or when a high frame rate is required. A longer exposure time will improve
image quality but it may lower the total frame rate and result in increased motion blur. In Axis network
cameras, an automatic exposure setting means the frame rate will increase or decrease with the amount
of available light. It is only as the light level decreases that you need to have artificial light or prioritize
frame rate or image quality.
31
The following chapters outline how a small- to mid-sized IP-Surveillance system can be implemented
using Axis network video products and AXIS Camera Station software.
Server selection
This chapter discusses general server recommendations, hard disk selection, network-attached storage
and RAID as they relate to the installation of the AXIS Camera Station software and its hard disk clean-
up procedure.
General server recommendations for AXIS Camera Station
The table above outlines the recommendations for server requirements in implementing an IP-Surveil-
lance system using AXIS Camera Station as the video management software. The recommendations are
not minimum requirements.
Notes:
> The figures are based on viewing and recording video with a 640x480 resolution and a 25 percent
compression rate using Motion JPEG. Raising the resolution, frame rate and image quality will raise
the requirements for the server.
> The CPU recommendation is based on Intel Dual Core processors. Other options such as Xeon Dual
may lower the CPU requirement.
> Using H.264 or MPEG-4 recording will reduce bandwidth and hard disk requirements.
> For best performance and stability, use local hard disks or a high performance network storage
solution for storing recordings.
> Software-based RAID systems should not be used since performance bottlenecks could result. A good
hardware RAID controller with fast disks could be a good option to secure your recordings.
> The disk drive (normally C:) where Windows and AXIS Camera Station are installed should have enough
disk space for the AXIS Camera Station log files. Allow at least 1 GB free disk space for the log files.
> The AXIS Camera Station Client requires a good graphics adaptor with at least 256 MB of memory and
support for DirectX 9.0C.
Hard disks
When selecting hard disks for your surveillance solution, keep in mind that the recording of a continuous
stream of video from multiple cameras will add more load on the hard drive than a standard office PC or
mail server.
There are three main hard drive solutions on the market:
1. SCSI
2. Serial ATA
3. IDE
4.2.
4.
4.1.
Number of
cameras
Server:
Recommended hardware
Client:
Recommended hardware
Hard disks Bandwidth CPU (GHz) RAM (GB) Graphics CPU (GHz) RAM (GB)
10 1 100 Dual Core 2.0 1 256 Dual Core 2.0 1
20 2 1000 Dual Core 3.0 2 512 Dual Core 3.0 3
30 2-3 1000 Core2 quad 2 512 Core2 quad 2
40 3 1000 Core2 quad 3 512 Core2 quad 3
50 4 1000 Core2 Extreme 4 768 Core2 Extreme 4
32
SCSI is the best solution in terms of reliability (and also the most expensive), followed in order by Serial
ATA and IDE. Note that Serial ATA and IDE are made for office desktops and not for 24-hour server op-
erations, as a surveillance solution demands. Since it is difficult to predict how long such hard disks will
last, Serial ATA and IDE disks should be installed in a way that makes them easy to replace.
Network-attached storage (NAS) and RAID
This section describes how AXIS Camera Station can use NAS to store recordings.
AXIS Camera Station will record video on the hard drive. The video will remain there for the number of
days specified in the configuration.
For each drive that is used for recording, you will need to specify how much disk space should be dedi-
cated for recording purposes. If the amount of disk space used is exceeded, AXIS Camera Station will
remove the oldest recording to ensure that there is enough space for ongoing recordings.
For each camera, you will need to specify the number of days that recordings should be stored. A special
option called Unlimited can be selected. The camera will then record for as many days as there is space
on the hard drive before AXIS Camera Station removes the oldest recordings.
Figure 4.3.a. AXIS Camera Station: Recording storage settings
When using remote disks or NAS, you will need to ensure that the necessary bandwidth is available to
move recordings from the AXIS Camera Station server to the archive drives. Keep in mind that in a
network-attached storage setup, live streams from the cameras are running while data is being moved
to the NAS.
Using Redundant Array of Independent Disks (RAID) setup
RAIDwhich is a method of arranging hard drives in such a way that the operating system sees them as
one large, logical hard diskcan be used to secure your recordings and configuration, but it must be
implemented with caution.
4.3.
33
RAID is mostly configured in three different ways:
When RAID 1 or 5 is used, data is written twice, over two hard disks (one for the primary data disk and
one for the mirror disk). This has an impact on performance since all disk writes are doubled in a RAID
setup. When multiple cameras are streaming data to the hard drives, the RAID controller will handle the
load using buffers and distribute the data to the disks. Since the hard disk write is doubled and there is
a limit of how many write per second the setup can handle, a RAID setup can become a bottleneck in a
video surveillance system if it is not implemented correctly.
There are three usual ways to implement RAID:
1) Using a software solution that can configure two or more hard disks into a RAID setup. This is a
very slow implementation and should never be used for a video surveillance system.
2) The CPU comes with an on-board RAID solution. This is a hardware implementation that may have
limited performance and should be used with caution.
3) Full hardware implementation with a separate RAID controller. This is the only recommended way
to implement RAID for a video surveillance solution. Make sure you use a well-known and well-
proven RAID technology as your surveillance solution will rely on it.
AXIS Camera Station hard disk cleanup procedure
While the AXIS Camera Station recording engine is running, some procedures are continuously executed
to ensure that your hard disks do not become full. The procedures include:
1) Comparing recorded images with the current date and configured days to record. If the saved re-
cordings have passed the number of days that they should be stored in the primary hard drive, the im-
ages are removed.
2) Freeing up space on the primary hard drive for current recordings. If the space available on the primary
drive is less than what is specified in the configuration, an emergency cleanup is invoked. This means that
the oldest recordings from all cameras are deleted and space is freed up for current recordings.

4.4.
RAID Level Characteristics
RAID-0
Data is being striped (divided) over two or several hard disks for improved read/write speed but no redundancy. There is
no advantage of using this setup with the AXIS Camera Station.
RAID-1
This is also known as disk mirroring since all hard disks are mirrored one by one. At least two disks duplicate data. Both
disks can be read at the same time. Write performance as for single disk storage.
RAID-5 Minimum of three hard disks. One of the hard disks is used to mirror the others (in theory).
34
AXIS Camera Station installation and configuration
This chapter provides an overview of the AXIS Camera Station installation and configuration processes
covering registration, camera setup, recording methods, bandwidth control and security.
Installing AXIS Camera Station
AXIS Camera Station should be installed on a dedicated, standalone PC where you wish to run the main
administration of your network cameras and video encoders. When the program is installed, it will ask
you to register your license. The license key can only be used on one computer. Once the license key is
registered, it cannot be used again. Therefore, the AXIS Camera Station must be installed on the target
computer when activating the software.
You can choose to activate one of four AXIS Camera Station alternatives, either automatically or
manually:
a) Licensed Version
b) Grace Period (which allows you to use the software for five days)
c) Demo (30-day trial version for four cameras. When the period expires, you will be required to register
the software.)
d) AXIS Camera Station One Free Version
Figure 5.1.a. AXIS Camera Station installation alternatives
Setting up a network camera/video encoder in AXIS Camera Station
After installing the AXIS Camera Station, it must be configured for your network cameras and video
encoders. The first time the software is configured, a search function automatically finds and installs the
network cameras/video encoders on your network. If there are more cameras/video encoders on your
network than you have licenses for, this procedure will be stopped. To add or remove a network camera/
video encoder at a later date, you can either manually enter the IP address of the network video product,
or click the Search button to get a list of video products on your network. Once a video product is im-
ported into AXIS Camera Station, you will need to choose a master user name and password if the
cameras are set up to use a common user name and password, or enter a specific user name and pass-
word for a specific camera.
5.2.
5.
5.1.
35
Customize the view in AXIS Camera Station
AXIS Camera Station offers a number of different ways and layouts to view one or many cameras simul-
taneously. These are called Auto views, My Views, Shared Views and Camera Views. Auto Views are
predefined (showing views from cameras that are added to AXIS Camera Station) and cannot be changed.
My views and Shared views enable users to customize the viewing layout. Cameras can then be arranged
by simply dragging and dropping a camera into the desired viewing location. Camera Views enables the
user to select the specific camera to open its Live View.
Figure 5.2.a AXIS Camera Stations live view screen
For each individual camera, you can specify the image settings (streaming format, quality, frame rate
and size) to be used for live viewing. This setting will be used in live views except in views with nine or
more cameras where the settings are fixed to optimize the performance of the PC.
Recording methods
For each camera, you can select one of three recording methods to use:
1) continuous
2) triggered by motion or alarm
3) manual (start/stop recordings from the user interface)
Continuous and triggered recordings can be scheduled to run at selected times during each day of the
week.

5.3.
Menu
Links to
workspaces
View groups
Audio and
PTZ controls
Alarm log
Recording indicator
Toolbar
36
Figure 5.3.a. Making recording settings using AXIS Camera Station.
For each camera, you can specify the image settings (streaming format, quality, frame rate and size) to
be used for recording. The settings will affect the amount of bandwidth used, as well as the amount of
storage space required.
For recordings triggered by video motion detection, AXIS Camera Station uses the Axis network camera/
encoders built-in motion detection functionality. This reduces bandwidth usage and processing load on
the server. (More about video motion detection is covered in Chapter 6.) With recordings triggered by
external inputs/outputs (I/O triggered recording), simply define the alarm trigger for the selected camera(s)
that will record when the alarm is triggered. The length of the pre- and post-alarm image buffers can be
set by defining the number of seconds the camera/encoder should record before and after an alarm is
triggered. The image buffers help to provide a more comprehensive picture of an event. Recording only
when motion or alarm is detected will save hard disk space compared with continuous recording.
The AXIS Camera Stations background service automatically starts running upon system start-up. When
the background service is running, recording will continue even after a user has logged out from the PC
where AXIS Camera Station is installed.
Event handling
AXIS Camera Station has an event handler that is built into the recording engine. It allows you to con-
figure the actions to be taken when defined events are triggered. Triggers in AXIS Camera Station are
classified under two categories: video motion detection and input/output.
Video motion detection is triggered when an Axis camera/video encoder detects motion within its defined
viewing area. The detection is performed by the Axis camera/video encoder so there is no processing load
on the AXIS Camera Station server. (More about video motion detection is covered in Chapter 6.)
5.4.
37
External devices such as a door contact, a glass break detector or a passive infrared detector (PIR) that
are connected to the input or output ports of a camera/video encoder can also be used as triggers by
AXIS Camera Station. In addition, other intelligent video functionalitiesfor example, active camera
tamperingthat are supported in a network camera/video encoder can be used by AXIS Camera Station
if they are first configured (through the network video products web interface) to trigger the output
port of the network video product.
Event/alarm responses include initiating recordings from selected cameras, raising an alarm, showing a
live image from a selected camera, setting an external output device such as sounding a siren, and send-
ing e-mail notifications.
Calculating your hard disk requirements
Network video products utilize network bandwidth based on their configuration. Bandwidth usage de-
pends on five criteria:
1) Image resolution (the higher the resolution, the more bandwidth is required)
2) Compression type (H.264 requires much less bandwidth than MPEG-4 and Motion JPEG)
3) Compression ratio (the higher the compression, the lower the bandwidth usage)
4) Frame rate (the higher the frame rate, the higher the bandwidth usage)
5) Image complexity (the more motion or scene changes, the higher the bandwidth usage)
The above criteria can be set either in the AXIS Camera Station software or in the network camera or
video encoder itself. A simulation-based calculation tool called the AXIS Design Tool is available at
www.axis.com/products/video/design_tool/ (or on a DVD) and helps provide guidance on a network
video products bandwidth and storage requirements based on the five criteria mentioned earlier.

Figure 5.5.a. AXIS Design Tool user interface
You can reduce the use of bandwidth and storage space if you record only when motion or alarm is de-
tected compared with continuous recording and if you use the H.264 or MPEG-4 compression format.
5.5.
38
Security aspects
A high level of security can be implemented in the AXIS Camera Station. The software can inherit the
Windows user database (local or LDAP/Domain) and you can grant or deny users access to a specific
camera. This feature allows you to use your current user database without having to set up and maintain
a separate database of users.
Once a user is defined, you select the user-access level. Three levels are available:
1) Administrator full access to all of AXIS Camera Stations functionalities
2) Operator Access to all functionalities (including recorded events) except the configuration pages
under Options
3) Viewer Access only to live video
For each user, you can choose which cameras the user will be allowed to access. There are also options
to allow/deny access to functions such as audio and PTZ control for each user or camera.

Figure 5.6a. AXIS Camera Station allows an administrator to select which camera and functionality a user may have access to.
5.6.
39
Video motion detection
This section describes how video motion detection works in the network camera or video encoder and
how it functions with AXIS Camera Station.
The built-in video motion detection feature in Axis network cameras or video encoders is used to gener-
ate an alarm whenever movement occurs in the viewing area. You can configure a number of included
windows (a specific area in an image where you want motion to be detected), as well as excluded
windows (areas within an included window that should be ignored).

Figure 6a. Setting recording instructions using the network cameras or video encoders video motion detection functionality.

When configuring for video motion detection, you can adjust the size of the window where you want
motion to be detected and drag the window to the desired position. You can then adjust sliders for the
object size (how large the object should be in order for the trigger to activate), history (how far back in
time the reference point for motion detection should be), and sensitivity (how big the pixel changes
should be in order to trigger an alarm).
Any detected motion within an active window is then indicated by red peaks in the activity window (the
active window has a red frame).
Once the video motion detection is configured, AXIS Camera Station will monitor the function and start
recording when the motion flag is raised by the network camera/video encoder. This is a very efficient
way of doing video motion detection as all the image processing is done by the network camera/video
encoder and not by the AXIS Camera Station server.
6.
40
Daily operation
This chapter describes the functions in the AXIS Camera Station that may be used on a daily basis: events
search, live image viewing, log files and configuration check, as well as remote connections.
Events search
AXIS Camera Station offers easy ways to search for recorded events. The Event Search function pulls up re-
cordings that are triggered by alarms or by manual recordings. The 4-camera Playback function plays simul-
taneous recordings from up to four cameras, enabling users to obtain a comprehensive picture of events.
















Figure 7.1a. By selecting the camera and the date, AXIS Camera Station will search for and display the recordings.
To search, simply select a camera and the date and time, and you will get sample images of all events
found. Double-clicking on the image plays the recorded sequence. Another option is to view the recorded
events on a timeline. This will show when recordings are present during a selected period of time, as well
as the type of recording (manual, continuous or triggered).
Each recorded event can be locked from the log search window. This means that the event recording will
not be deleted even if the AXIS Camera Station engine detects that the event is older than the config-
ured days to keep recordings. The event recording will remain on the hard drive until it is unlocked.
During playback, you can zoom into the video and continue to playback the stream in zoomed-in mode.
Figure 7.1.b. Recording playback with timeline
7.
7.1.
41
Single or multiple event recordings can be exported to ASF files from the event list. The ASF files include
the selected streaming formats decoder and are playable from Windows Media Player, so any Windows
client with Media Player installed should be able to view the recording.
Live images, PTZ and audio controls
The AXIS Camera Station provides four different ways to view live images:
1) Split view
2) Single camera view
3) Monitor mode (full screen)
4) Sequence/salvos (A camera sequence is a pre-defined tour that automatically switches to all of
the cameras included in the tour.)
AXIS Camera Station also enables pan/tilt/zoom (PTZ) control when working with a PTZ or dome network
camera. The software allows you to control the PTZ function of the camera by 1) clicking on a display
keypad, 2) using a mouse (you can click in the image to move the camera or zoom in using the mouse
scroll wheel), or 3) using the AXIS 295 Video Surveillance Joystick.

In live view, you can also do digital pan/tilt/zoom. This means that when you are using a fixed camera,
you can zoom and steer within the cameras view.

Figure 7.2.a. Screenshot of live view with PTZ and audio controls.
If the camera is equipped with audio capability, the audio controls will be automatically shown in the
AXIS Camera Station program.
7.2.
Master audio
control
PTZ control
Audio control
in image
42
Log files
The AXIS Camera Station provides three types of log files: alarm, event and audit. The alarm log shows
customer-configured alarms as defined in the event configuration, as well as some system-related mes-
sages. The event log provides a list of camera and server events based on date, time, type and source of
the events. You can sort or search, for example, for a list of errors or when motion is detected.
Figure 7.3.a. The event log provides a list of events such as errors or change in motion detection status.
The audit log allows you to generate a list of user actions based on the user, time, type of activity and
camera. All user activities are logged in AXIS Camera Station. All fields in the generated list can be fil-
tered and sorted.
Figure 7.3.b. The audit log notes all user activities.
7.3.
43
Configuration overview
For maintenance purposes, the AXIS Camera Stations configuration sheet enables you to obtain, in one
place, an overview of all camera and recording configurations. The sheet is accessible from the Help
menu.
Figure 7.4.a. AXIS Camera Stations configuration sheet provides an overview of all camera and recording configurations.
Remote connections

Figure 7.5.a. Using AXIS Camera Stations Windows client software
7.4.
7.5.
AXIS Camera Station
software
Axis network cameras
Analog cameras
Network
switch
AUDIO
I/O
IN
OUT 1 2 3 4 5 6
Axis video encoder
VIEWING, PLAYBACK
and ADMINISTRATION
RECORDING
DATABASE
VIEWING, PLAYBACK
and ADMINISTRATION
Remote access via
AXIS Camera Station
Client software
AXIS Camera Station
Client software
Broadband
router
INTERNET
IP NETWORK
VIEWING, PLAYBACK
and ADMINISTRATION
BACKGROUND
SERVICE
Coax
cables
44
The AXIS Camera Station Client program enables local as well as remote operations on client workstations
using the same user interface. The client application lets you work as if you are operating directly on the
AXIS Camera Station recording server. Once the Client program is installed, you simply enter the IP ad-
dress or host name of the server PC where AXIS Camera Station is installed and, if required, enter the user
name and password. The Client will download and inherit the camera settings from the AXIS Camera Sta-
tion server. From the same client, you can also switch between different AXIS Camera Station servers.
Figure 7.5.b. You can also switch between different AXIS Camera Station servers using the client software
VIEWING, PLAYBACK
and ADMINISTRATION
Remote access via
AXIS Camera Station
Client software
AUDIO I/O
IN OUT 1 2 3 4 5 6
INTERNET
AUDIO I/O
IN OUT 1 2 3 4 5 6 AUDIO I/O
IN OUT 1 2 3 4 5 6
45
Scaling up your surveillance system
AXIS Camera Station enables you to easily add more cameras to the system, while the client application
allows you to work with multiple AXIS Camera Station servers.
Adding more cameras
AXIS Camera Station allows you to easily add cameras to the system simply by using the Add function.
You can add as many cameras to the system as the purchased license allows. If the number of cameras
exceeds the number allowed under license, simply purchase an add-on license.
Network considerations
When implementing 10 cameras or more, try to estimate the load on the network using a few rules of
thumb:
> A camera will use approx. 2 to 3 megabits of bandwidth when configured to deliver high-quality
images at high frame rates. The bandwidth usage will be significantly lowered using H.264 or MPEG-4
streaming compared with Motion JPEG.
> In a system with more than 12-15 cameras, consider using a switch with a gigabit backbone. If a
gigabit-supporting switch is used, the server that runs the video management software should have
a gigabit network adapter installed.
Consider also using Quality of Service (QoS) on your network. Quality of Service enables reservation of
network capacity and prioritization of mission-critical surveillance. Some Axis network video products
support QoS.
Figure 8.2.a. The above is an example of a QoS aware network, where Router 1 has been configured to devote a certain amount of
maximum bandwidth usage to streaming video, FTP traffic, and HTTP and all other traffic. The maximum usage applies only when
there is congestion on the network. If there is unused bandwidth available, any type of traffic can take advantage of it. (In an ordi-
nary or non-QoS network, there is no reserved bandwidth usage for different types of traffic, so when there is network congestion,
there is no guarantee that video streams will be able to maintain the desired frame rate.)
Server considerations
If you are adding more cameras, you should monitor the servers CPU usage so that it does not exceed
its limitations. One hard disk is suitable for storing recordings from six to eight cameras. With more than
12-15 cameras, at least two hard disks should be used to split the load. For 50 or more cameras, the use
of a second server is recommended. The AXIS Camera Station Client will be able to switch between dif-
ferent AXIS Camera Station servers.
For more information, please refer to the hardware recommendation sheet on page 31.
8.
8.1.
8.2.
100 Mbit
Switch 1 Switch 2
Router 2 Router 1
PC 1
PC 2
PC 3
Camera 1
Camera 2
100 Mbit
100 Mbit
FTP 2
Video 5
HTTP 3
10 Mbit
F
T
P
Video
8.3.
Number of cameras Considerations
1 to 15 1 disk
15 to 30 2 disks
30 to 40 3 disks
40 to 50 4 disks
50+ 2 servers
46
Storage considerations
When the amount of stored data and management requirements exceed the limitations of a direct at-
tached storage, a network-attached storage (NAS) or storage area network (SAN) allows for increased
storage space, flexibility and recoverability.
Figure 8.4.a. Network-attached storage
NAS provides a single storage device that is directly attached to a LAN and offers shared storage to all
clients on the network. A NAS device is simple to install and easy to administer, providing a low-cost
storage solution. However, it provides limited throughput for incoming data because it has only one
network connection, which can become problematic in high-performance systems.
SANs are high-speed, special-purpose networks for storage, typically connected to one or more servers
via fiber. Users can access any of the storage devices on the SAN through the servers, and the storage is
scalable to hundreds of terabytes. Centralized storage reduces administration and provides a high perfor-
mance, flexible storage system for use in multi-server environments. In a SAN system, files can be stored
block by block on multiple hard disks. Technologies such as Fiber Channel are commonly used, providing
data transfers at four gigabits per second. This type of hard disk configuration allows for very large and
scalable solutions where large amounts of data can be stored with a high level of redundancy.
Figure 8.4.b. A typical SAN architecture where a fiber channel network ties all storage devices together and lets the servers share
the storage capacity.
8.4.
Computer server with video
management software
Network switch,
broadband router or
coprorate firewall Axis network cameras
Separate
storage
Server Server Server Server
TCP/IP LAN
Fiber channel switch
RAID disk
array
Fiber channel Fiber channel
RAID disk
array
Tape
47
Redundant Storage
SAN systems build redundancy into the storage device. Redundancy in a storage system allows video, or
any other data, to be saved simultaneously in more than one location. This provides a backup for recov-
ering video if a portion of the storage system becomes unreadable. There are a number of options for
providing this added storage layer in an IP-Surveillance system, including a Redundant Array of Indepen-
dent Disks (RAID), data replication, server clustering and multiple video recipients.
RAID -- RAID is a method of arranging standard, off-the-shelf hard drives such that the operating sys-
tem sees them as one large hard disk. A RAID set up spans data over multiple hard disk drives with
enough redundancy so that data can be recovered if one disk fails. There are different levels of RAID -
ranging from practically no redundancy to a full-mirrored solution in which there is no disruption and
no loss of data in the event of a hard disk failure.

Data replication -- This is a common feature in many network operating systems. File servers in the net-
work are configured to replicate data among each other providing a back up if one server fails.
Server clustering -- A common server clustering method is to have two servers work with the same
storage device, such as a RAID system. When one server fails, the other identically configured server
takes over. These servers can even share the same IP address, which makes the so-called fail-over
completely transparent for users.
Multiple video recipients -- A common method to ensure disaster recovery and off-site storage in
network video is to simultaneously send the video to two different servers in separate locations. These
servers can be equipped with RAID, work in clusters, or replicate their data with servers even further
away. This is an especially useful approach when surveillance systems are in hazardous or not easily ac-
cessible areas, such as in mass-transit installations or industrial facilities.
The variety of storage options available for IP-Surveillance systems makes it crucial to consider the dif-
ferent ways the information will be used and stored for the long term. As hard drive technology contin-
ues to advance, it is important to utilize open standards to ensure that storage is scalable and future
proof. In addition, advances in IP-Surveillance, such as intelligent video algorithm, will make it even more
critical to select open storage devices that can handle combinations of data from different sources.
Storage systems should be able to accommodate new and upcoming applications so that equipment
investments are not lost as technology advances.

48
Conclusion
We hope this document has been helpful in providing guidelines for implementing an IP-Surveillance
system. While there are many considerations to take into account, it is relatively easy to set up and
operate an Axis IP-Surveillance system once you have defined your application requirements and deter-
mined the components you require.
Setting up an Axis IP-Surveillance system Quick checklist:
> Define your surveillance needs
- Draw a plan of your installation
- Select points of interest to view (area of coverage)
- Position each camera: define what you want to be able to capture with each camera
- Consider environment: light conditions
- Consider cabling to cameras
- Position the recording server
> Network camera and/or video encoder selection
- Image quality requirements: resolution, compression and frame rate
- Light sensitivity and lens selection (re: camera)
- Outdoor/indoor, fixed/fixed dome/PTZ/PTZ dome network camera
- Consider needs such as Power over Ethernet (PoE), video motion detection, audio
- Housing, mounting and other accessories
- Buy and try: Buy one camera to test its quality
> Hardware components
- Additional switches (PoE, wireless options)
- Additional light sources
- Power supplies and eventually UPS
- Server for video management software
- Hard drives (local disks, SAN, RAID, etc.)
> Software
- Select a software package for your required functionality
- Purchase licenses that fit the number of cameras
- Specify image quality and frame rate requirements for each camera
- IP address range for cameras and servers
- Calculate hard disk usage
- Configure your cameras and their recording settings
- Configure video motion detection settings
- Grant user access and authentications
> Operations and maintenance
- Check recorded events for all your cameras
- Check motion detection settings again
- Check hard disk free space and eventually adjust recording options
Appendix
Letter chart on page 49. (Place the letter chart at the distance where you want an image to be captured.
Rows 5 and 6 should be clear for recognition purposes; rows 7 and 8 and most gray shades should be
clear for identification purposes.) Printed with permission from SKL Statens kriminaltekniska laboratorium
9.
10.
49
www.axis.com
3
2
5
6
8
/
E
N
/
R
3
/
0
8
0
7
About Axis Communications
Axis is an IT company offering network video solutions
for professional installations. The company is the global
market leader in network video, driving the ongoing
shift from analog to digital video surveillance. Axis
products and solutions focus on security surveillance
and remote monitoring, and are based on innovative,
open technology platforms.
Axis is a Swedish-based company, operating worldwide
with offices in more than 20 countries and cooperating
with partners in more than 70 countries. Founded in 1984,
Axis is listed on the OMX Nordic Exchange under the
ticker AXIS. For more information about Axis, please visit
our website at www.axis.com.
2008 Axis Communications AB. AXIS COMMUNICATIONS, AXIS, ETRAX, ARTPEC and VAPIX are registered trademarks or trademark applications of Axis AB
in various jurisdictions. All other company names and products are trademarks or registered trademarks of their respective companies. We reserve the right
to introduce modifications without notice.