I nst r uct i on Manual

Threaded I nser t Power Tool

74200
3
Cont ent s
Safety Rules 4
Tool Specications 5
Intent of Use 6
Tool Dimensions 6
Putting into Service
Air Supply 7
Stroke Adjustment 7
Operating Procedure 7
Nose Assemblies
Fitting & Servicing Instructions 8
Selection 9
Servicing the Tool
Daily / Weekly 10
Molykote 55M Safety Data 10
Service Kit 11
Maintenance
Pneumatic Cylinder 12
Rod Guide 12
Trigger 12
Swivel Air Inlet 12
Differential Valve 13
Head Assembly 13
Rear Casing 13
Distributor 13
Hydraulic Piston & Air Motor Assembly 13
General Assembly of Base Tool
General Assembly and Parts List 14-15
Priming
Oil Details & Safety Data 16
Priming Procedure 16
Fault Diagnosis
Symptom, Possible Cause & Remedy 17-18
LIMITED WARRANTY
Avdel makes the limited warranty that its products will be free of defects in workmanship and materials
which occur under normal operating conditions. This Limited Warranty is contingent upon: (1) the product
being installed, maintained and operated in accordance with product literature and instructions, and (2)
conrmation by Avdel of such defect, upon inspection and testing. Avdel makes the foregoing limited
warranty for a period of twelve (12) months following Avdels delivery of the product to the direct purchaser
from Avdel. In the event of any breach of the foregoing warranty, the sole remedy shall be to return the
defective Goods for replacement or refund for the purchase price at Avdels option. THE FOREGOING
EXPRESS LIMITED WARRANTY AND REMEDY ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES
AND REMEDIES. ANY IMPLIED WARRANTY AS TO QUALITY, FITNESS FOR PURPOSE, OR MERCHANTABILITY
ARE HEREBY SPECIFICALLY DISCLAIMED AND EXCLUDED BY AVDEL.
Avdel UK Limited policy is one of continuous product development and improvement and we reserve the right to change the specication of any product without prior notice.
4
Saf et y Rul es
1 Do not use outside the design intent.
2 Do not use equipment with this tool/machine other than that recommended and supplied by Avdel UK Limited.
3 Any modication undertaken by the customer to the tool/machine, nose assemblies, accessories or any equipment supplied by
Avdel UK Limited or their representatives, shall be the customers entire responsibility. Avdel UK Limited will be pleased to advise
upon any proposed modication.
4 The tool/machine must be maintained in a safe working condition at all times and examined at regular intervals for damage and
function by trained competent personnel. Any dismantling procedure shall be undertaken only by personnel trained in Avdel UK
Limited procedures. Do not dismantle this tool/machine without prior reference to the maintenance instructions. Please contact
Avdel UK Limited with your training requirements.
5 The tool/machine shall at all times be operated in accordance with relevant Health and Safety legislation. In the U.K. the Health
and Safety at Work etc. Act 1974 applies. Any question regarding the correct operation of the tool/machine and operator safety
should be directed to Avdel UK Limited.
6 The precautions to be observed when using this tool/machine must be explained by the customer to all operators.
7 Always disconnect the airline from the tool/machine inlet before attempting to adjust, t or remove a nose assembly.
8 Do not operate a tool/machine that is directed towards any person(s) or the operator.
9 Always adopt a rm footing or a stable position before operating the tool/machine.
10 Ensure that vent holes do not become blocked or covered and that hoses are always in good condition.
11 The operating pressure shall not exceed 7 bar (100 lbf/in
2
).
12 Do not operate the tool without full nose equipment, oil plug and oil bleed screw in place.
13 When using the tool, the wearing of safety glasses is required both by the operator and others in the vicinity to protect against pin
ejection, should a fastener be placed in air. We recommend wearing gloves if there are sharp edges or corners on the
application.
14 Take care to avoid entanglement of loose clothes, ties, long hair, cleaning rags etc. in the moving parts of the tool which should
be kept dry and clean for best possible grip.
15 When carrying the tool from place to place keep hands away from the trigger/lever to avoid inadvertent start up.
16 Excessive contact with hydraulic oil should be avoided. To minimise the possibility of rashes, care should be taken to wash
thoroughly.
This instruction manual must be read with particular attention to the following safety rules, by any person
installing, operating, or servicing this tool.
Tool Speci f i cat i on
Speci f i cat i ons
5
Air Pressure Minimum - Maximum 5-7 bar (75-100 lbf/in
2
)
Free Air Volume Required @ 5 bar/75 lbf/in
2
8 litres (.28 ft
3
)
Stroke Maximum 7 mm (.276 in)
Motor Speed Spin On 2000 rpm
Spin Off 2000 rpm
Pull Force @ 5 bar/75 lbf/in
2
19.1 kN (4300 lbf)
Cycle time Approximately 2.5 seconds
Noise Level Less than 75 dB(A)
Weight Without nose equipment 2.2 kg (4.85 lb)
Vibration Less than 2.5 m/s
2
(8 ft/s
2
)
6
I nt ent of Use
The hydro-pneumatic 74200 tool is designed to place Avdel

threaded inserts at high speed making it ideal for batch or ow-line assembly in a
wide variety of applications throughout all industries.
A complete tool is made up of the base tool (part number 74200-12000) and the appropriate nose assembly for the insert, as
described on page 9.
NOSE ASSEMBLIES MUST BE FITTED AS DESCRIBED ON PAGE 8.
115
4.53
280
11.02
63
2.48
9.84
250
63
2.48
27
1.06
Dimensions shown in bold are millimetres. Other dimensions are in inches.
Tool Di mensi ons
Ai r Suppl y
St roke Adj ust ment
Operat i ng Procedure
Put t i ng i nt o Ser vi ce
7
All tools are operated with compressed air at an optimum pressure of 5.5 bar. We recommend the use of pressure regulators and
automatic oiling/ltering systems on the main air supply. These should be tted within 3 metres of the tool (see diagram below) to
ensure maximum tool life and minimum tool maintenance.
Air supply hoses should have a minimum working effective pressure rating of 150% of the maximum pressure produced in the system
or 10 bar, whichever is the highest. Air hoses should be oil resistant, have an abrasion resistant exterior and should be armoured
where operating conditions may result in hoses being damaged. All air hoses MUST have a minimum bore diameter of 6.4 millimetres
or
1
/4 inch.
Read servicing daily details page 10.
8 6
4
2
0
10121
41 6
TAKE OFF POINT
FROM MAIN SUPPLY
STOP COCK
(USED DURING MAINTENANCE
OF FILTER/REGULATOR
OR LUBRICATION UNITS)
MAIN SUPPLY
DRAIN POINT
PRESSURE REGULATOR
AND FILTER
(DRAIN DAILY)
LUBRICATOR
3
M
ETRES MAXIMUM
Connect tool to air supply.
Offer up insert, lip rst to drive screw. A light pressure will start the motor and automatically thread the insert up against nose and
stop.
Insert fastener into application squarely.
Fully depress trigger. This will both place insert into the application and reverse it off the drive screw.
This adjustment is necessary to ensure optimum insert deformation. It
is suggested, therefore, that a test plate with the same thickness and
hole size as workpiece be used.
If deformation is insufficient, the insert will rotate inside the application.
If deformation is excessive, thread distortion will occur and possibly
drive screw fracture.
The stroke is adjusted by the amount the rear casing 86 is screwed in or
out. To shorten stroke, screw in; to lengthen stroke, unscrew the rear
casing but never more than 5 turns from the fully IN position unless
dismantling the tool. Adjust until optimum deformation is obtained.
Lock the stroke set nger 88 into the rear casing.
Item numbers in bold refer to the General Assembly drawing and parts list (pages 14-15).
8
Fi t t i ng I nst ruct i ons
Ser vi ci ng I nst ruct i ons
Nose Assembl i es
It is essential that the correct nose assembly is tted prior to operating the tool. By knowing the details of the fastener to be placed,
you will be able to order a new complete nose assembly using the selection tables on page 9.
I M P O R T A N T
The air supply must be disconnected when tting or removing nose assemblies unless specically instructed
otherwise.
Nose assemblies should be serviced at weekly intervals.
Remove the complete nose assembly using the reverse procedure to the Fitting Instructions.
Any worn or damaged part should be replaced by a new part.
Particularly check wear on drive screw.
Assemble according to tting instructions.
* Refers to items included in the 74200 service kit. For complete list see page 11.
Item numbers in bold refer to illustration below:
If still tted remove the nose casing and the adaptor nut.
Insert drive shaft 4 into spindle.
Fit drive screw 3 onto drive shaft 4.
Insert reducing sleeve 5 (if specied) into the adaptor nut.
Screw the adaptor nut onto the spindle.
Hold the spindle with a spanner* and tighten the adaptor nut clockwise.
While holding the adaptor nut with the spanner*, tighten the lock nut anti-clockwise.
Screw on the nose casing and nose tip 1 with the nose tip lock nut.
The reverse operation is carried out for equipment removal.
With tool still disconnected from air supply, screw one insert onto drive screw manually - making sure the insert is ush with the
end of drive screw.
Set nose tip in exact position and lock nose tip nut clockwise with a spanner*.
Remove the insert from drive screw.
1 2
FRICTION RING
4 3
5
SPINDLE LOCK NUT
ADAPTOR NUT NOSE CASING
Items in grey are included in the base tool.
Items in black make up the nose assembly.
9
Nose Assembl i es
Nose tips vary in shape according to the insert type. Each nose assembly represents a unique assembly of components which can be
ordered individually. All nose assemblies also include a nose tip locknut 2 (part number 07555-00901). Component numbers refer
to the illustration on the opposite page. We recommend some stock as items will need regular replacement. Read the Nose
Assemblies servicing instructions opposite carefully.
74200-00083
74200-00084
74200-00085
74200-00485
74200-00086
74200-00088
74200-00080
74200-00082
74200-00054
74200-00056
74200-00058
74200-00050
74200-00048
74200-00040
74200-00042
74200-00070
74200-00068
74200-00060
74200-00062
74200-00016
74200-00018
74200-00010
LARGE FLANGE INSERTS (9698,FS58,9408,9418,9498) + STANDARD NUTSERT

(9500) + SQUARESERT

(GK08) + EUROSERT

(GJ08)
74200-00183
74200-00184
74200-00185
74200-00186
74200-00188
74200-00180
74200-00182
74200-00154
74200-00156
74200-00158
74200-00150
74200-00148
74200-00140
74200-00170
74200-00168
74200-00160
74200-00116
74200-00118
74200-00130
74200-00132
74200-00134
M3
M4
M5
M6
M8
M10
M12
4 UNC
6 UNC
8 UNC
10 UNC
1
/4 UNC
5
/16 UNC
10 UNF
1
/4 UNF
5
/16 UNF
3
/16 BSW
1
/4 BSW
0BA
2BA
4BA
THIN SHEET NUTSERT

(9468, FS38, 9650, 9488 )

74200-00283
74200-00284
74200-00285
74200-00286
74200-00288
74200-00258
74200-00250
74200-00248
74200-00278
74200-00270
74200-00268
M3
M4
M5
M6
M8
8 UNC
10 UNC
1
/4 UNC
8 UNF
10 UNF
1
/4 UNF
SUPERSERT

- OPEN AND CLOSED END ( FB )

74200-00683
74200-00684
74200-00685
74200-00686
74200-00688
M3
M4
M5
M6
M8
07555-00903
07555-00904
07555-00905
07555-00915
07555-00906
07555-00908
07555-00910
07555-00912
07555-00854
07555-00856
07555-00858
07555-00850
07555-00848
07555-00840
07555-00842
07555-00850
07555-00848
07555-00840
07555-00842
07555-00850
07555-00848
07555-00840
07555-00993
07555-00994
07555-00995
07555-00996
07555-00998
07555-00999
07555-00992
07555-00954
07555-00956
07555-00958
07555-00950
07555-00948
07555-00940
07555-00950
07555-00948
07555-00940
07555-00950
07555-00948
07555-00996
07555-00950
07555-00934
07555-07103
07555-07104
07555-07105
07555-07106
07555-07108
07555-07158
07555-07150
07555-07148
07555-07158
07555-07150
07555-07148
07555-08103
07555-08104
07555-08105
07555-08106
07555-00998

07555-09003
07555-09004
07555-09005
07555-09005
07555-09006
07555-09008
07555-09010
07555-09012
07555-09054
07555-09056
07555-09058
07555-09050
07555-09048
07555-09040
07555-09042
07555-09070
07555-09068
07555-09060
07555-09062
07555-09016
07555-09018
07555-09019
07555-09003
07555-09004
07555-09005
07555-09006
07555-09008
07555-09010
07555-09012
07555-09054
07555-09056
07555-09058
07555-09050
07555-09048
07555-09040
07555-09070
07555-09068
07555-09060
07555-09016
07555-09018
07555-09030
07555-09032
07555-09034
07555-09003
07555-09004
07555-09005
07555-09006
07555-09008
07555-09058
07555-09050
07555-09048
07555-09078
07555-09070
07555-09068
07555-09003
07555-09004
07555-09005
07555-09006
07555-09008
07555-01003
07555-01004
07555-01005
07555-01005
07555-01006
07555-01008
07555-01010
07555-01012
07555-00754
07555-00756
07555-00758
07555-00750
07555-00748
07555-00740
07555-00742
07555-00750
07555-00748
07555-00740
07555-00742
07555-00750
07555-00748
07555-00740
07555-01003
07555-01004
07555-01005
07555-01006
07555-01008
07555-00758
07555-00750
07555-00748
07555-00758
07555-00750
07555-00748
07555-01003
07555-01004
07555-01005
07555-01006
07555-01008
07555-09103
07555-09104
07555-09105
07555-09105
07555-09106
07555-09108

07555-09154
07555-09156
07555-09158
07555-09150
07555-09148
07555-09140

07555-09150
07555-09148
07555-09140

07555-09150
07555-09148
07555-09140
07555-09103
07555-09104
07555-09105
07555-09106
07555-09108

07555-09154
07555-09156
07555-09158
07555-09150
07555-09148
07555-09140
07555-09150
07555-09148
07555-09140
07555-09150
07555-09148
07555-09106
07555-09150
07555-09134
07555-09103
07555-09104
07555-09105
07555-09106
07555-09108
07555-09158
07555-09150
07555-09148
07555-09158
07555-09150
07555-09148
07555-09103
07555-09104
07555-09105
07555-09106
07555-09108
HEXSERT

( 9688 )

Places all inserts listed in this section except M5 large flange Thin Sheet Nutsert

Places M5 large flange Thin Sheet Nutsert 09698-00516 ONLY

These nose assemblies include an adaptor nut part number 74200-12119 to replace the one on the tool.
INSERT
SIZE
M3
M4
M5

M5

M6
M8
M10
M12
4 UNC
6 UNC
8 UNC
10 UNC
1
/4 UNC
5
/16 UNC
3
/8 UNC
10 UNF
1
/4 UNF
5
/16 UNF
3
/8 UNF
3
/16 BSW
1
/4 BSW
5
/16 BSW
07555-09883
07555-09884
07555-09885
07555-09185
07555-09886
07555-09888
07555-09880
74200-09882
07555-09854
07555-09856
07555-09858
07555-09850
07555-09848
07555-09840
07555-09842
07555-09870
07555-09868
07555-09860
07555-09862
07555-09816
07555-09818
07555-09810
07555-09983
07555-09984
07555-09985
07555-09986
07555-09988
07555-09980
74200-09982
07555-09954
07555-09956
07555-09958
07555-09950
07555-09948
07555-09940
07555-09970
07555-09968
07555-09960
07555-09916
07555-09918
07555-09930
07555-09932
07555-09934
07555-09583
07555-09584
07555-09585
07555-09586
07555-09588
07555-09558
07555-09550
07555-09548
07555-09578
07555-09570
07555-09568
07555-09283
07555-09284
07555-09285
07555-09286
07555-09288

COMPLETE TOOL NOSE ASSEMBLY 1 3 4 5

07555-01003
07555-01004
07555-01005
07555-01006
07555-01008
07555-01010
07555-01012
07555-00754
07555-00756
07555-00758
07555-00750
07555-00748
07555-00740
07555-00750
07555-00748
07555-00740
07555-00750
07555-00748
07555-01006
07555-00750
07555-00756
10
Ser vi ci ng t he Tool
I M P O R T A N T
The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate personnel.
The operator should not be involved in maintenance or repair of the tool unless properly trained.
Daily, before use or when rst putting the tool into service, pour a few drops of clean, light lubricating oil into the air inlet of the tool if no
lubricator is tted on air supply. If the tool is in continuous use, the air hose should be disconnected from the main air supply and the tool
lubricated every two to three hours.
Check for air leaks. If damaged, hoses and couplings should be replaced by new items.
If there is no lter on the pressure regulator, bleed the air line to clear it of accumulated dirt or water before connecting air hose to tool.
Check that the nose assembly is correct.
Check the stroke of the tool is adequate to place selected insert. (See stroke adjustment page 7).
Inspect the drive screw in the nose assembly for wear or damage. If any, renew.
Check for oil leaks and air leaks on air supply hose and ttings.
Grease can be ordered as a single item, the part number is shown in the service kit page 11.
First Aid
SKIN: Wipe off and wash with soap and water.
INGESTION: No adverse effects are normally expected.
Treat symptomatically.
EYES: Irritant but not harmful. Irrigate with water and seek medical attention.
Environment
Scrape up for incinerating or disposal on approved site.
Fire
FLASH POINT: 101C
Not classied as ammable.
Suitable extinguishing media: Carbon dioxide, foam, dry powder or ne water spray.
Handling
Plastic or rubber gloves should be worn.
Storage
Away from heat and oxidising agent.
Regular servicing should be carried out and a comprehensive inspection performed annually or every 500,000 cycles, whichever is sooner.
Dai l y
Weekl y
Mol ykot e 55m Saf et y Dat a
Ser vi ce Ki t
Ser vi ci ng t he Tool
11
For all servicing we recommend the use of the service kit (part number 74200-99990) supplied in its own plastic case.
07900-00393 14mm/15mm SPANNER 1
07900-00409 12mm/13mm SPANNER 1
07900-00626 11mm SPANNER 1
07900-00469 2.5mm ALLEN KEY 1
07900-00351 3mm ALLEN KEY 1
07900-00224 4mm ALLEN KEY 1
07900-00225 5mm ALLEN KEY 1
07900-00620 12mm ALLEN KEY 1
07900-00456 T BAR 1
07992-00075 MOLYKOTE 55M (100 gm TUBE) 1
07900-00627 PLASTIC CASE 1
07900-00632 17mm/19mm SPANNER 2
07900-00618 PUSHER 1
07900-00619 GUIDE BUSH 1
07900-00478 3mm PIN PUNCH 1
07900-00624 4mm PIN PUNCH 1
07900-00157 INTERNAL CIRCLIP PLIERS 1
07900-00161 EXTERNAL CIRCLIP PLIERS 1
07900-00625 SOFT MALLET 1
07900-00623 25mm SOCKET 1
07900-00006 SPATULA 1
07900-00434 32mm SPANNER 1
07900-00621 28mm SPANNER 1
07900-00637 17mm SPANNER 1
07900-00643 PUSHER KNOB 1
ITEM PART N DESCRIPTION N OFF
SERVICE KIT
ITEM PART N DESCRIPTION N OFF
SERVICE KIT (Continued)
12
Mai nt enance
Every 500,000 cycles the tool should be completely dismantled and components replaced where worn, damaged or when
recommended. All O rings and seals should be replaced with new ones and lubricated with Molykote 55M grease before assembling.
I M P O R T A N T
Safety Instructions appear on page 4.
The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate personnel.
The operator should not be involved in maintenance or repair of the tool unless properly trained.
Remove rubber base 2.
Place tool, base uppermost in vice tted with soft jaws.
Using a spanner*, unscrew end plug 3. Pneumatic piston 9 should move upward under spring 11 pressure (it may be necessary
to exert hand pressure to pneumatic piston 9).
Remove O ring 4.
Withdraw pneumatic piston 9.
Remove lip seal 8 and O ring 36.
Hold piston rod 10 in soft vice jaws to avoid scratching rod diameter.
Separate piston rod 10 from pneumatic piston 9 by unscrewing piston rod fastening bolt 5 using a spanner*.
Inspect air tube 12 for damage or distortion. (Air tube is screwed internally into handle and set in position with Loctite 222) If it is
necessary to remove air tube, the base of the air tube will require warming to a temperature of 100o C to soften the Loctite
adhesive. The air tube 12 can then be unscrewed from the handle using an Allen key*.
Check spring 11 is not distorted or damaged.
Assembly is in reverse order to dismantling.
The airline must be disconnected before any servicing or dismantling is attempted unless specically instructed otherwise.
It is recommended that any dismantling operation be carried out in clean conditions.
Before proceeding with dismantling, empty the oil from the tool. Remove oil plug 42, oil seal washer 43, bleed screw 48 and bleed screw
washer 49 from the handle assembly and drain the oil into a suitable container.
Prior to dismantling the tool it is necessary to remove the nose assembly. For simple removal instructions see the nose assemblies
section, pages 8-9.
For total tool servicing we advise that you proceed with dismantling of sub-assemblies in the order shown below.
* Refers to items included in the 74200 service kit. For complete list see page 11.
Item numbers in bold refer to the General Assembly drawing and parts list (pages 14-15).
With tool in upside down position in vice, unscrew rod guide 15 using a spanner* and T-bar*.
Withdraw rod guide 15.
Unscrew locknut 13 using an Allen key*, remove seal 14 and O ring 98.
Remove O ring 16.
Assembly is in reverse order to dismantling.
With tool held in vice, remove pin 26 using a pin punch*.
Remove trigger 25, pin 22, roller 23 and push wedge 24.
Gently push on the head of trigger rod 20 and, remove together with O rings 7 and 21, guide 19, lip seal 18 and plug 17.
Assembly is in reverse order to dismantling. Ensure lip of lip seal 18 is towards head of tool.
Using an Allen key* remove screw 40 and washer 39.
Remove swivelling inlet 38.
Unscrew double male connector 41 from swivelling inlet 38 and remove nylon washer 33.
Using a spanner*, remove drilled bolt 37.
Remove two nylon washers 33 and air inlet block 35.
Remove circlip 97 from double male connector 41 using circlip pliers and withdraw sintered lter 96.
Assemble in reverse order of dismantling.
Pneumat i c Cyl i nder
Rod Gui de
Tri gger
Swi vel Ai r I nl et ( 74200- 12700)
Di f f erent i al Val ve
Head Assembl y
Rear Casi ng
Di st ri but or
Hydraul i c Pi st on & Ai r Mot or Assembl y ( 74200- 12610)
Mai nt enance
13
Wrap adhesive tape around hydraulic piston 54 thread and move assembly backwards slowly and rmly. Using circlip pliers* remove
circlip 52 and front seal 51.
Remove O rings 76 and 77.
Using two spanners* separate the hydraulic piston 54 from air motor casing 75. Shim adjustment ring 55, movement pivot 56 and
O ring 101 will come out with hydraulic piston 54.
Remove air motor assembly out of air motor casing 75, remove circlip 61 using circlip pliers*, then tap air motor casing 75 on bench to
free components.
Parts 62 to 74 can be pulled out as an assembly, taking care not to drop pin 74.
Remove bearing 62, planet gear spindle 63, three planets 64, planet gear 65 and spacer 66.
Using a soft mallet tap splined head of rotor 70.
Bearing 67 and front end plate 68 will come out with stator 69 and ve rotor blades 71. (rotor 70 remains in hand).
Place rear end plate 72 in vice with soft jaws.
Using a pin punch* tap centre of rotor 70 to remove bearing 73. (turn rotor 70 upside down and bearing 73 will come out).
When assembling air motor, rear side of rotor 70 must just touch rear end plate 72 without any axial gap, (any existing gap will disappear
when bearing 73 is fully located.
When inserting air motor into air motor casing 75 carefully align parts so that pin 74 locates in centre hole between spin on/off ports of
air motor casing 75 and rear end plate 72.
When assembling hydraulic piston 54 onto air motor assembly, tighten parts by hand and blow air into one of the outer ports of air motor
casing 75, checking to see air motor rotates freely.
When assembling front seal 51 ensure larger diameter faces rear of tool.
Complete assembly in reverse order to dismantling.
* Refers to items included in the 74200 service kit. For complete list see page 11.
Item numbers in bold refer to the General Assembly drawing and parts list (pages 14-15).
I M P O R T A N T
Check the tool against daily and weekly servicing.
Priming is ALWAYS necessary after the tool has been dismantled and prior to operating
Using special at spanner* unscrew valve locking plug 27, withdraw and remove spring 104 and O ring 29.
Remove silencer 34 using a spanner* and remove nylon washer 33.
Push valve piston 28 out from its housing together with O rings 30, 31 & 32.
Check spring 104 for distortion and renew if required.
Assemble in reverse order of dismantling.
Remove nose equipment prior to commencing dismantling.
Using spanners* remove spindle 44 and locknut 45.
Remove return spring locknut 46 using a spanner*.
Remove return spring 47, washer 99 and locking ring 90.
Check return spring 47 for distortion and renew if required.
Assemble in reverse order of dismantling.
Using an Allen key* remove screw 40 from stroke set nger 88 and lift off bridge washer 95.
Disengage stroke set nger 88 by pushing it back against spring 89.
Unscrew rear casing 86.
Remove rear casing rubber band 87 if necessary.
Extract circlip 84 using circlip pliers* and remove sintered silencer 85.
Complete assembly in reverse order of dismantling. Locate pawl 102 in head before screwing on rear casing 86.
Using an Allen key* remove two screws 40.
Withdraw distributor 83 together with air motor end plug 81 and O rings 82 & 31 taking care not to drop ball 79 and push rod 78.
Using an Allen key* remove four countersunk socket head screws 58 and withdraw stroke stop 57.
Pull out two air supply tubes 59 and four O rings 60.
Assemble in reverse order of dismantling.
14
Gener al Assembl y of Base Tool 74200- 12000
8
3
3
1
8
2
8
1
6
4
0
8
4
8
5
8
6
8
7
6
1
6
2
6
3
6
4
6
5
6
6
6
7
6
8
6
9
7
0
7
1
7
2
7
3
7
4
7
5
7
6
7
7
7
8
7
9
1
3
3
3
4
9
1
2
5
2
6
2
2
2
4
9
2
9
0
9
0
9
9
4
4
4
5
4
6
4
7
2
1
2
0
1
9
1
8
1
7
7
4
2
4
3
6
0
5
9
4
0
8
9
9
5
8
8
1
0
2
5
0
4
9
4
8
2
3
5
1
5
2
5
4
5
3
5
5
5
6
1
0
1
5
8
5
7
3
2
3
1
2
9
2
8
2
7
3
0
1
0
4
3
8
3
6
3
9
4
0
4
1
9
7
9
6
3
7
3
3
3
3
3
3
3
5
3
6
3
6
1
0
3
5
2 3 4 8
1
5
1
6
1
2
9
1
4
1
3
9
8
1
0
1
1
1
1
5
1
1
3
1
1
4
15
Par t s Li st f or 74200- 12000
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5
3
6
3
7
3
8
3
9
7
4
2
0
0
-
1
2
0
0
1
7
4
2
0
0
-
1
2
0
0
2
7
4
2
0
0
-
1
2
0
0
3
7
4
2
0
0
-
1
2
0
0
4
7
4
2
0
0
-
1
2
0
0
5
0
7
0
0
2
-
0
0
1
0
9
0
7
0
0
3
-
0
0
0
2
7
7
4
2
0
0
-
1
2
0
0
8
7
4
2
0
0
-
1
2
0
0
9
7
4
2
0
0
-
1
2
0
1
0
0
7
5
5
5
-
0
0
2
0
5
7
4
2
0
0
-
1
2
0
1
2
7
4
2
0
0
-
1
2
0
1
3
7
4
2
0
0
-
1
2
0
1
4
7
4
2
0
0
-
1
2
0
1
5
0
7
0
0
3
-
0
0
1
0
0
7
4
2
0
0
-
1
2
0
1
7
7
4
2
0
0
-
1
2
0
1
8
7
4
2
0
0
-
1
2
0
1
9
7
4
2
0
0
-
1
2
0
2
0
0
7
0
0
3
-
0
0
3
1
5
7
4
2
0
0
-
1
2
0
2
2
7
4
2
0
0
-
1
2
0
2
3
7
4
2
0
0
-
1
2
0
2
4
7
4
2
0
0
-
1
2
0
2
5
7
4
2
0
0
-
1
2
0
2
6
7
4
2
0
0
-
1
2
0
2
7
7
4
2
0
0
-
1
2
0
2
8
0
7
0
0
3
-
0
0
0
8
6
0
7
0
0
3
-
0
0
0
4
0
0
7
0
0
3
-
0
0
0
2
6
0
7
0
0
3
-
0
0
0
4
6
7
4
2
0
0
-
1
2
0
3
3
7
4
2
0
0
-
1
2
0
3
4
7
4
2
0
0
-
1
2
0
3
5
0
7
0
0
3
-
0
0
0
2
9
7
4
2
0
0
-
1
2
0
3
7
7
4
2
0
0
-
1
2
0
3
8
7
4
2
0
0
-
1
2
0
3
9
H
E
A
D

&

H
A
N
D
L
E
R
U
B
B
E
R

B
A
S
E
E
N
D

P
L
U
G

(
S
C
R
E
W
E
D
)
'
O
'

R
I
N
G
P
I
S
T
O
N

R
O
D

F
A
S
T
E
N
I
N
G

B
O
L
T
M
4

S
H
A
K
E
P
R
O
O
F

W
A
S
H
E
R

'
O
'

R
I
N
G


L
I
P

S
E
A
L

(
P
N
E
U
M
A
T
I
C

P
I
S
T
O
N
)
P
N
E
U
M
A
T
I
C

P
I
S
T
O
N
P
I
S
T
O
N

R
O
D

(
I
N
T
E
N
S
I
F
I
E
R
)
S
P
R
I
N
G
A
I
R

S
U
P
P
L
Y

T
U
B
E
L
O
C
K

N
U
T
S
E
A
L
R
O
D

G
U
I
D
E
'
O
'

R
I
N
G
P
L
U
G
L
I
P

S
E
A
L
G
U
I
D
E
T
R
I
G
G
E
R

R
O
D
'
O
'

R
I
N
G
P
I
N
R
O
L
L
E
R
P
U
S
H

W
E
D
G
E
T
R
I
G
G
E
R
P
I
N
V
A
L
V
E

L
O
C
K
I
N
G

P
L
U
G
V
A
L
V
E

P
I
S
T
O
N
'
O
'

R
I
N
G
'
O
'

R
I
N
G
'
O
'

R
I
N
G
'
O
'

R
I
N
G
1
/
8
"

N
Y
L
O
N

W
A
S
H
E
R
1
/
8
"

S
I
L
E
N
C
E
R
A
I
R

I
N
L
E
T

B
L
O
C
K
'
O
'

R
I
N
G
D
R
I
L
L
E
D

B
O
L
T
S
W
I
V
E
L
L
I
N
G

I
N
L
E
T

W
A
S
H
E
R
111112211111111111111111111111214114111
-
1
-
1
--
21
--
11
-
1
-
1
-
1
--
111
-
11
--
112141
-
4
--
1
4
0
4
1
4
2
4
3
4
4
4
5
4
6
4
7
4
8
4
9
5
0
5
1
5
2
5
3
5
4
5
5
5
6
5
7
5
8
5
9
6
0
6
1
6
2
6
3
6
4
6
5
6
6
6
7
6
8
6
9
7
0
7
1
7
2
7
3
7
4
7
5
7
6
7
7
7
8
0
7
0
0
1
-
0
0
4
2
0
7
4
2
0
0
-
1
2
0
4
1
0
7
0
0
5
-
0
1
2
7
4
7
4
2
0
0
-
1
2
0
4
3
7
4
2
0
0
-
1
2
0
4
4
0
7
5
5
5
-
0
0
8
0
3
7
4
2
0
0
-
1
2
0
4
6
7
4
2
0
0
-
1
2
0
4
7
0
7
0
0
1
-
0
0
3
2
9
0
7
0
0
3
-
0
0
0
3
3
0
7
2
6
5
-
0
3
0
2
1
0
7
2
6
5
-
0
2
0
0
4
0
7
0
0
4
-
0
0
0
3
3
7
4
2
0
0
-
1
2
0
5
3
7
4
2
0
0
-
1
2
0
5
4
7
4
2
0
0
-
1
2
0
5
5
7
4
2
0
0
-
1
2
0
5
6
7
4
2
0
0
-
1
2
0
5
7
0
7
0
0
1
-
0
0
4
2
7
7
4
2
0
0
-
1
2
0
5
9
7
4
2
0
0
-
1
2
0
6
0
7
4
2
0
0
-
1
2
0
6
1
7
4
2
0
0
-
1
2
0
6
2
7
4
2
0
0
-
1
2
0
6
3
0
7
5
5
5
-
0
9
2
0
8
7
4
2
0
0
-
1
2
0
6
5
7
4
2
0
0
-
1
2
0
6
6
0
7
5
5
5
-
0
9
2
0
6
0
7
5
5
5
-
0
9
2
1
0
0
7
5
5
5
-
0
9
2
1
1
7
4
2
0
0
-
1
2
0
7
0
0
7
5
5
5
-
0
9
2
1
3
0
7
5
5
5
-
0
9
2
1
4
0
7
5
5
5
-
0
9
2
1
5
0
7
5
5
5
-
0
9
2
1
6
7
4
2
0
0
-
1
2
0
7
5
0
7
0
0
3
-
0
0
3
0
5
0
7
0
0
3
-
0
0
3
0
6
7
4
2
0
0
-
1
2
0
7
8
M
4

B
U
T
T
O
N

S
O
C
K
E
T

H
D

S
C
R
E
W
1
/
4
"

D
O
U
B
L
E

M
A
L
E

C
O
N
N
E
C
T
O
R
O
I
L

P
L
U
G
O
I
L

S
E
A
L

W
A
S
H
E
R
S
P
I
N
D
L
E
L
O
C
K

N
U
T
R
E
T
U
R
N

S
P
R
I
N
G

L
O
C
K
N
U
T
R
E
T
U
R
N

S
P
R
I
N
G
M
5

B
L
E
E
D

S
C
R
E
W
O
I
L

S
E
A
L

B
L
E
E
D

W
A
S
H
E
R
S
U
S
P
E
N
S
I
O
N

R
I
N
G
F
R
O
N
T

S
E
A
L
C
I
R
C
L
I
P
S
E
A
L
H
Y
D
R
A
U
L
I
C

P
I
S
T
O
N
S
H
I
M

A
D
J
U
S
T
M
E
N
T

R
I
N
G
M
O
V
E
M
E
N
T

P
I
V
O
T
S
T
R
O
K
E

S
T
O
P
M
5

C
S
K

S
O
C
K
E
T

H
E
A
D

S
C
R
E
W
P
N
E
U
.

M
O
T
O
R

A
I
R

S
U
P
P
L
Y

T
U
B
E
'
O
'

R
I
N
G
C
I
R
C
L
I
P
B
E
A
R
I
N
G
P
L
A
N
E
T

G
E
A
R

S
P
I
N
D
L
E
P
L
A
N
E
T
P
L
A
N
E
T

G
E
A
R
S
P
A
C
E
R
B
E
A
R
I
N
G
F
R
O
N
T

E
N
D

P
L
A
T
E
S
T
A
T
O
R
R
O
T
O
R
R
O
T
O
R

B
L
A
D
E
R
E
A
R

E
N
D

P
L
A
T
E
B
E
A
R
I
N
G
P
I
N
A
I
R

M
O
T
O
R

C
A
S
I
N
G
'
O
'

R
I
N
G
'
O
'

R
I
N
G
P
U
S
H

R
O
D


8
0

m
m

L
O
N
G
411111111111111111424111311111151111151
4
-
111111111111
-
11
-
4241
---------
5
--
1
-
151
7
9
8
0
8
1
8
2
8
3
8
4
8
5
8
6
8
7
8
8
8
9
9
0
9
1
9
2
9
3
9
4
9
5
9
6
9
7
9
8
9
9
1
0
0
1
0
1
1
0
2
1
0
3
1
0
4
1
0
5
1
0
6
1
0
7
1
0
8
1
0
9
1
1
0
1
1
1
1
1
2
1
1
3
1
1
4
1
1
5
7
4
2
0
0
-
1
2
0
7
9
0
7
0
0
7
-
0
1
5
0
3
7
4
2
0
0
-
1
2
0
8
1
7
4
2
0
0
-
1
2
0
8
2
7
4
2
0
0
-
1
2
0
8
3
7
4
2
0
0
-
1
2
0
8
4
7
4
2
0
0
-
1
2
0
8
5
7
4
2
0
0
-
1
2
0
8
6
7
4
2
0
0
-
1
2
0
8
7
7
4
2
0
0
-
1
2
0
8
8
7
4
2
0
0
-
1
2
0
8
9
0
7
0
0
3
-
0
0
0
2
8
7
4
2
0
0
-
1
2
0
9
1
7
4
2
0
0
-
1
2
0
9
2
7
4
2
0
0
-
1
2
0
9
3
0
7
9
0
0
-
0
0
3
5
4
7
4
2
0
0
-
1
2
0
9
5
7
4
2
0
0
-
1
2
0
9
6
7
4
2
0
0
-
1
2
0
9
7
0
7
0
0
3
-
0
0
1
3
4
7
4
2
0
0
-
1
2
0
9
9
0
7
0
0
7
-
0
1
5
2
6
7
4
2
0
0
-
1
2
1
2
1
7
4
2
0
0
-
1
2
1
2
2
7
4
2
0
0
-
1
2
1
0
3
7
4
2
0
0
-
1
2
1
0
4
0
7
9
0
0
-
0
0
6
1
4
0
7
9
0
0
-
0
0
6
3
2
0
7
9
0
0
-
0
0
4
0
9
0
7
9
0
0
-
0
0
2
2
4
0
7
9
0
0
-
0
0
2
2
5
0
7
9
0
0
-
0
0
6
2
4
0
7
9
0
0
-
0
0
6
3
7
0
7
9
0
0
-
0
0
4
6
9
7
4
2
0
0
-
1
2
3
0
0
7
4
2
0
0
-
1
2
7
0
0
0
7
3
4
0
-
0
0
4
0
1
B
A
L
L

(
R
U
B
B
E
R
)
B
O
O
K
M
A
R
K

L
A
B
E
L
A
I
R

M
O
T
O
R

E
N
D

P
L
U
G
'
O
'

R
I
N
G
D
I
S
T
R
I
B
U
T
O
R
C
I
R
C
L
I
P
S
I
N
T
E
R
E
D

S
I
L
E
N
C
E
R
R
E
A
R

C
A
S
I
N
G
R
E
A
R

C
A
S
I
N
G

R
U
B
B
E
R

B
A
N
D
S
T
R
O
K
E

S
E
T

F
I
N
G
E
R
S
P
R
I
N
G
L
O
C
K
I
N
G

R
I
N
G
N
O
S
E

C
A
S
I
N
G
A
D
A
P
T
O
R

N
U
T

(
U
P

T
O

M
1
0
)
C
O
L
O
U
R
E
D

L
A
B
E
L
T
I
E

O
N

S
A
F
E
T
Y

L
A
B
E
L
B
R
I
D
G
E

W
A
S
H
E
R
S
I
N
T
E
R
E
D

F
I
L
T
E
R
E
D
C
I
R
C
L
I
P
'
O
'

R
I
N
G
W
A
S
H
E
R
'
C
E
'

L
A
B
E
L

(
A
V
D
E
L

I
T
A
L
Y
)
'
O
'

R
I
N
G
P
A
W
L

(
R
U
B
B
E
R
)
P
L
U
G
S
P
R
I
N
G
T
O
O
L

M
A
N
U
A
L
1
7
/
1
9

M
M

T
H
I
N

S
P
A
N
N
E
R
1
2
/
1
3

M
M

S
P
A
N
N
E
R
4

M
M

A
L
L
E
N

K
E
Y
5

M
M

A
L
L
E
N

K
E
Y

4

M
M

P
I
N

P
U
N
C
H

S
P
E
C
I
A
L

1
7

M
M

F
L
A
T

S
P
A
N
N
E
R
2
.
5

M
M

A
L
L
E
N

K
E
Y
D
E
F
L
E
C
T
O
R

A
S
S
E
M
B
L
Y
I
N
L
E
T

A
S
S
E
M
B
L
Y
S
P
R
I
N
G
111211111112111111111111112111111111
1N
/
I
-
2
-
11
-
1112
-
1N
/
I
N
/
I
11111N
/
I
111N
/
I
N
/
I
N
/
I
N
/
I
N
/
I
N
/
I
N
/
I
N
/
I
N
/
I
I
T
E
M
P
A
R
T

N

D
E
S
C
R
I
P
T
I
O
N
Q
T
Y
R
E
C
.
S
P
A
R
E
S
I
T
E
M
P
A
R
T

N

D
E
S
C
R
I
P
T
I
O
N
Q
T
Y
R
E
C
.
S
P
A
R
E
S
I
T
E
M
P
A
R
T

N

D
E
S
C
R
I
P
T
I
O
N
Q
T
Y
R
E
C
.
S
P
A
R
E
S
7
4
2
0
0
-
1
2
0
0
0

P
A
R
T
S

L
I
S
T
16
Oi l Det ai l s
Hyspi n VG 32 Oi l Saf et y Dat a
Pri mi ng Procedure
Pr i mi ng
Priming is ALWAYS necessary after the tool has been dismantled and prior to operating. It may also be necessary to restore the full
stroke after considerable use, when the stroke may be reduced and fasteners are not fully placed by one operation of the trigger.
The recommended oil for priming is Hyspin VG32 available in 0.5l (part number 07992-00002) or one gallon containers (part
number 07992-00006). Please see safety data below.
I M P O R T A N T
All operations should be carried out on a clean bench, with clean hands in a clean area.
Ensure that the oil is perfectly clean and free from air bubbles.
Care MUST be taken at all times, to ensure that no foreign matter enters the tool, or serious damage may result.
The tool must remain on its side throughout the priming sequence
Place tool on its side, oil plug 42 side up.
Pull back stroke set nger 88 and unscrew rear casing 86 by a maximum of 5 turns from the fully IN position.
With an Allen key, unscrew oil plug 42 and remove with oil seal washer 43.
Fill tool with priming oil rocking gently to expel air.
Replace oil seal washer 43 and oil plug 42 and tighten.
You must now bleed the tool. This operation is to ensure air bubbles are eliminated from the oil circuit.
Ensuring oil bleed screw 48 is fully tightened unscrew by ONE TURN only, using an Allen key. Connect the tool to the air supply
and depress the trigger.
Wait until oil appears all around oil bleed screw 48 then re-tighten. Wipe excess oil away.
Release the trigger.
Using an Allen Key open oil plug 42.
Top-up with priming oil to reset level. Replace oil seal washer 43 and oil plug 42 and fully tighten.
It is necessary to t the appropriate nose equipment and adjust the tool stroke prior to operating the tool.
Item numbers in bold refer to general assembly drawings and parts list (pages 14-15).
First Aid
SKIN:
Wash thoroughly with soap and water as soon as possible. Casual contact requires no immediate attention. Short term contact
requires no immediate attention.
INGESTION:
Seek medical attention immediately. DO NOT induce vomiting.
EYES:
Irrigate immediately with water for several minutes. Although NOT a primary irritant, minor irritation may occur following contact.
Fire
Flash point 232C. Not classied as ammable.
Suitable extinguishing media: CO2, dry powder, foam or water fog. DO NOT use water jets.
Environment
WASTE DISPOSAL: Through authorised contractor to a licensed site. May be incinerated. Used product may be sent for reclamation.
SPILLAGE: Prevent entry into drains, sewers and water courses. Soak up with absorbent material.
Handling
Wear eye protection, impervious gloves (e.g. of PVC) and a plastic apron. Use in well ventilated area.
Storage
No special precautions.
17
Faul t Di agnosi s
Pneumatic motor Air leak from motor Check for worn seals. Replace 13
runs slowly Low air pressure Increase 7
Air way blockage Clear restriction in air supply
Worn drive screw Replace 8
Vanes jamming Lubricate tool through air inlet
Insert does not Stroke incorrectly set Adjust 7
deform properly Air pressure outside the tolerance Adjust 7
Low oil level Prime tool 16
Insert out of grip Check grip range of Insert
Drivescrew turns Worn or damaged drive shaft Replace
independent of Worn or damaged drive screw Replace 8
motor Adaptor nut loose Tighten 8
Locking ring 90 missing Fit new locking ring 13
Insert will not Incorrect Insert thread size Change to correct insert
place onto Incorrect drive screw tted Change to correct drive screw
drivescrew Worn or damaged drive screw Replace
Nose equipment incorrectly assembled Disconnect air supply, re-t nose 8-9
equipment carefully
Tool is jammed Excessive stroke/ DO NOT DEPRESS TRIGGER. Unlock
on placed insert Defective insert/ stroke locking device and bring
Worn or defective drive screw rear casing forward to zero stroke
position. Depress trigger. Tool
should spin off. Reset stroke. If not,
disconnect air to tool. Insert a
4 mm pin through nose casing slots
into spindle 44. Turn until drive screw
leaves. Insert. Use new insert AND
drive screw.
Drive screw Stroke of tool excessive Re-set stroke
breaks Side load on drive screw Hold tool square to application when
placing Insert
continued overleaf
Item numbers in bold refer to general assembly drawings and parts list (pages 14-15).
Other symptoms or failures should be reported to your local Avdel authorised distributor or repair centre.
Sympt om Possi bl e Cause Remedy Page Ref
18
Faul t Di agnosi s
Tool does not Screw adaptor nut loose Tighten
spin on No air supply Connect 7
Insufficient gap between locknut 45 and Adjust to 1.5 mm gap to 2mm gap 13
spindle 44
Push rod 78 too short Replace 13
Air motor jammed Lubricate tool at air inlet. If insufficient
dismantle and clean air motor thoroughly
Trigger Static friction Depress trigger a few times
inoperative Low air pressure Increase air pressure
Valve piston remains stuck Depress trigger several times. Lubricate
tool through air inlet. If unsuccessful,
dismantle, clean and lubricate trigger
elements
Drivescrew does Lip seal 18 is defective Replace 12
not return and/or
keeps spinning off
Tool does not Adaptor nut 92 loose Tighten
spin off No air supply Connect
Rear casing unscrewed by more than Set tool stroke
5 turns
O ring 82 leaking air Replace 13
Distributor stuck Lubricate
Air motor jammed Lubricate tool at air inlet. If insufficient
dismantle and clean air motor
thoroughly
Item numbers in bold refer to general assembly drawings and parts list (pages 14-15).
Other symptoms or failures should be reported to your local Avdel authorised distributor or repair centre.
Sympt om Possi bl e Cause Remedy Page Ref
19
Decl ar at i on of Conf or mi t y
We, Avdel UK Limited, Watchmead Industrial Estate, Welwyn Garden City, Herts, AL7 1LY
declare under our sole responsibility that the product:
Model Type 74200
Serial No. ................................................
to which this declaration relates is in conformity with the following standards:
EN ISO 12100 - parts 1 & 2
BS EN ISO 8662 - part 6 BS EN ISO 11202
BS EN ISO 3744 BS EN 982
ISO EN 792 - part 13 - 2000 BS EN 983
following the provisions of the Machine Directive 89/392/EC
(as amended by Directive 91/368/EC, 93/44/EC and 93/68/EC)
and superseded by 98/37/EC
This box contains a power tool which is in
conformity with Machines Directive
89/392/EC. The Declaration of Conformity
is contained within.
Date of issue
M. Delle Fave - Quality Manager

A
v
d
e
l

U
K

L
i
m
i
t
e
d


2
0
0
7
Manual No. Issue Change Note No. Date
AA 11-01
B 07/044 01-07
B2 07/103 03-07
07900-00614
www.avdel-global.com
AUSTRALIA
Acument Australia Pty Ltd.
891 Wellington Road
Rowville, Victoria 3178
Tel: +61 3 9765 6400
Fax: +61 3 9765 6445
Email: [email protected]
CANADA
Avdel Canada, a Division of Acument
Canada Limited
87 Disco Road
Rexdale
Ontario M9W 1M3
Tel: +1 416 679 0622
Fax: +1 416 679 0678
Email: [email protected]
CHINA
Acument China Ltd.
RM 1708, 17/F., Nanyang Plaza,
57 Hung To Rd., Kwun Tong
Hong Kong
Tel: +852 2950 0631
Fax: +852 2950 0022
Email: [email protected]
FRANCE
Avdel France S.A.S.
33 bis, rue des Ardennes
BP4
75921 Paris Cedex 19
Tel: +33 (0) 1 4040 8000
Fax: +33 (0) 1 4208 2450
Email: [email protected]
GERMANY
Avdel Deutschland GmbH
Klusriede 24
30851 Langenhagen
Tel: +49 (0) 511 7288 0
Fax: +49 (0) 511 7288 133
Email: [email protected]
ITALY
Avdel Italia S.r.l.
Viale Lombardia 51/53
20047 Brugherio (MI)
Tel: +39 039 289911
Fax: +39 039 2873079
Email: [email protected]
JAPAN
Acument Japan Kabushiki Kaisha
Center Minami SKY,
3-1 Chigasaki-Chuo, Tsuzuki-ku,
Yokohama-city, Kanagawa Prefecture
Japan 224-0032
Tel: +81 45 947 1200
Fax: +81 45 947 1205
Email: [email protected]
SINGAPORE
Acument Asia Pacic (Pte) Ltd.
#05-03/06 Techlink
31 Kaki Bukit Road 3
Singapore, 417818
Tel: +65 6840 7431
Fax: +65 6840 7409
Email: [email protected]
SOUTH KOREA
Acument Korea Ltd.
212-4, Suyang-Ri,
Silchon-Eup, Kwangju-City,
Kyunggi-Do, Korea, 464-874
Tel: +82 31 798 6340
Fax: +82 31 798 6342
Email: [email protected]
SPAIN
Avdel Spain S.A.
C/ Puerto de la Morcuera, 14
Poligono Industrial Prado Overa
Ctra. de Toledo, km 7,8
28919 Legans (Madrid)
Tel: +34 (0) 91 3416767
Fax: +34 (0) 91 3416740
Email: [email protected]
UNITED KINGDOM
Avdel UK Limited
Pacic House
2 Swiftelds
Watchmead Industrial Estate
Welwyn Garden City
Hertfordshire
AL7 1LY
Tel: +44 (0) 1707 292000
Fax: +44 (0) 1707 292199
Email: [email protected]
USA
Avdel USA LLC
614 NC Highway 200 South
Staneld,
North Carolina 28163
Tel: +1 704 888-7100
Fax: +1 704 888-0258
Email: [email protected]