Scribd
Upload
194 views3 pages

EP Lab (EEE and ECE)

This document outlines the experiments and equipment for an Electrical Engineering Practices Laboratory course. The course covers basic residential wiring, measurement of electrical quantities in circuits, motor wiring and testing, and electronics components and circuits. It is a 1 credit course divided into Electrical and Electronics sections. Students will conduct 10 experiments in groups over the semester, which will be examined through a 90 minute written test for each section. The laboratory is equipped with materials for house wiring, electrical measuring instruments, motors, starters, soldering equipment, and components for making electronic circuits.

Uploaded by

prithivgokul
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
194 views3 pages

EP Lab (EEE and ECE)

This document outlines the experiments and equipment for an Electrical Engineering Practices Laboratory course. The course covers basic residential wiring, measurement of electrical quantities in circuits, motor wiring and testing, and electronics components and circuits. It is a 1 credit course divided into Electrical and Electronics sections. Students will conduct 10 experiments in groups over the semester, which will be examined through a 90 minute written test for each section. The laboratory is equipped with materials for house wiring, electrical measuring instruments, motors, starters, soldering equipment, and components for making electronic circuits.

Uploaded by

prithivgokul
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

ENGINEERING PRACTICES LABORATORY L T P C

0 0 2 1

ELECTRICAL


ELECTRICAL ENGINEERING PRACTICE 10
1. Residential house wiring using switches, fuse, indicator, lamp and energy meter.
2. Fluorescent lamp wiring.
3. Stair case wiring
4. Measurement of electrical quantities voltage, current, power & power factor in RLC circuit.
1. Single phase induction motor connection and energy measurement.
2. Three phase induction motor with star delta starter and power measurement on No-Load
using two wattmeter method.
3. Measurement of resistance to earth of electrical equipment.
4. Study of iron box, fan & regulator and emergency lamp.


ELECTRONICS 13
1. Study of Electronic components and equipments Resistor, colour
coding measurement of AC signal parameter (peak-peak, rms
period, frequency) using CR.
2. Study of logic gates AND, OR, EOR and NOT.
3. Generation of Clock Signal.
4. Soldering practice Components Devices and Circuits Using
general purpose PCB.
5. Measurement of ripple factor of HWR and FWR.

SEMESTER EXAMINATION PATTERN

The Laboratory examination is to be conducted for Group A&Group B, allotting 90 minutes
for each group, with a break of 15 minutes. Both the examinations are to be taken together in
sequence, either in the FN session or in the AN session. The maximummarks for Group A
and Group B lab examinations will be 50 each, totaling 100 for the Lab course. The
candidates shall answer either I or II under Group A and either III or IV under Group B,
based on lots.



List of equipment and components
(For a Batch of 30 Students)

ELECTRICAL
1. Assorted electrical components for house wiring 15 Sets.
2. Electrical measuring instruments 10 Sets.
3. Study purpose items: Iron box, fan and regulator, emergency lamp 1 each.
4. Megger (250V/500V) 1 No.
5. Single phase induction motor 1 No.
6. Three phase induction motor 1 No.
7. Star Delta starter 1 No.



ELECTRONICS

1. Soldering guns 10 Nos.
2. Assorted electronic components for making circuits 50 Nos.
3. Small PCBs 10 Nos.
4. Multimeters 10 Nos.
5. Study purpose items: Telephone, FM radio, low-voltage power supply

REFERENCES


1. S. Gowri and T. Jeyapoovan, Engineering Practices Lab Manual, Vikas Publishing House Pvt
Ltd., First Edition, 2011.
2. K.Jeyachandran, S.Natarajan & S, Balasubramanian, A Primer on Engineering Practices
Laboratory, Anuradha Publications, (2007).
3. H.S. Bawa, Workshop Practice, Tata McGraw Hill Publishing Company Limited, (2007).
4. A. Rajendra Prasad & P.M.M.S. Sarma, Workshop Practice, Sree Sai Publication, (2002).
P.Kannaiah & K.L.Narayana, Manual on Workshop Practice, Scitech Publications, (1999).

You might also like