International Journal of Engineering Trends and Technology (IJETT) Volume 4 Issue 10 - Oct 2013

ISSN: 2231-5381 http://www.ijettjournal.org Page 4281

Application of Waste Foundry Sand for
Evolution of Low-Cost Concrete
Pathariya Saraswati C
1
, Rana Jaykrushna K
2
, Shah Palas A
3
, Mehta J ay G
4
,Assistant Prof. Patel Ankit N
5

1
Student of final year B.E. Civil, Sigma Institute of Engineering College, Vadodara
2
Student of final year B.E. Civil, Sigma Institute of Engineering College, Vadodara
3
Student of final year B.E. Civil, Sigma Institute of Engineering College, Vadodara
4
Student of final year B.E. Civil, Sigma Institute of Engineering College, Vadodara
5
Assistant Professor, Civil Engg. Department, Sigma Institute of Engineering College, Vadodara Gujarat-India.


AbstractGeneration of waste foundry sand as by-
product of metal casting industries causes
environmental problems because of its improper
disposal. Thus, its usage in building material,
construction and in other fields is essential for reduction
of environmental problems. This research is carried out
to produce a low-cost and eco-friendly concrete. This
paper demonstrates the use of waste foundry sand as a
partial replacement by fine aggregate in concrete. An
experimental investigation is carried out on a concrete
containing waste foundry sand in the range of 0%, 20%,
40%, and 60% by weight for M-25 grade concrete(PPC).
Material was produced, tested and compared with
conventional concrete in terms of workability and
strength. These tests were carried out on standard cube
of 150*150*150* mm for 7, 14 and 28 days to determine
the mechanical properties of concrete. Through
experimental result we conclude that the compressive
strength increases with increase in partial replacement
of waste foundry sand and split tensile strength
decreases with increases in percentage of waste foundry
sand. The aim of this research is to know the behaviour
and mechanical properties of concrete after addition of
industrial waste in different proportion by tests like
compressive strength and split tensile.
Keywords: - Industrial waste, Foundry sand, PPC,
Low-cost, Eco-friendly, Compressive strength, Split
tensile strength.
I. INTRODUCTION
Now-a-days the construction sector is exploring
rapidly on a large scale and also involves new
techniques for rapid and comfort works on the field.
Concrete as a building material plays an important
role in this sector. The consumption of natural
resources as an ingredient of concrete, costs high as
well as it is on verge of extent. These problems
force us to recover the natural resources or to find
an alternative option to overcome this problem.
Presently, the production of waste foundry sand as a
by-product of metal casting industries causes
various environmental problems. Usage of this
waste in building material would help in reduction
of stress on environment.
Metal industries use foundry sand which is uniform
sized, high quality silica sand that is bound to form a
mould for casting of ferrous and non-ferrous metal.
Finer sand than normal sand is used in metal casting
process. The burnt sand after the casting process of
metal is reuse for many times but when it cannot be
longer used it is removed from foundry as a waste
for disposal known as Waste foundry sand. Use of
waste foundry sand as a partial replacement or total
replacement by fine aggregate in concrete leads in
production of economic, light weight and high
strength concrete.
Concrete is a material which is composed of coarse
aggregate, fine aggregate, cement, admixtures and
water these each material in concrete contributes its
strength. So, by partial or percentage replacing of
material affects different properties of concrete. By
using such waste material which harms the
environment can be used for the development of low
cost and eco-friendly building materials. In this
study an experimental investigation is carried out by
varying percentage of fine aggregate with used
foundry sand to produce low cost and eco-friendly
concrete
II. EXPERIMENTAL MATERIALS
(a) Foundry sand
Most of the metal industries prefer sand
casting system. In this system mould made of
uniform sized, clean, high silica sand is used. After
casting process foundries recycle and reuse the sand
several times but after sometime it is discarded from
the foundries known as waste foundry sand. The
application of waste foundry sand to various
engineering sector can solve the problems of its
disposal and harmful effect to environment.
International Journal of Engineering Trends and Technology (IJETT) Volume 4 Issue 10 - Oct 2013
ISSN: 2231-5381 http://www.ijettjournal.org Page 4282

Foundry sand is clean, uniformly sized,
high-quality silica sand that is bounded to form
moulds for ferrous (iron and steel) and non-ferrous
(copper, aluminum, brass) metals. Type of foundry
sand depends on the casting process in foundries.
Foundry sand is generally of two types: Green sand,
Chemically bounded sand. Additive in sand depends
on type of metal casting. Use of waste foundry sand
as full or partial replacement by fine aggregate helps
to achieve different properties or behaviour of
concrete.

FIGURE: 1 Waste foundry sand
SOURCE: Concrete Lab, Sigma Institute of Engg.
TABLE-1
CHEMICAL PROPERTIES OF FOUNDRY SAND
Constituent Value (%)
SiO
2
83.93
Al
2
O
3
0.021
Fe
2
O
3
0.950
CaO 1.03
MgO 1.77
SO
3
0.057
LOI 2.19

SOURCE: Geo-Test House, Gorwa, Vadodara.
(b) Cement
Cement in concrete acts as a binding
material that harden after the addition of water. It
plays an important role in construction sector. In this
study the Portland Pozzolana Cement (PPC) of 53
grade (Sanghi Cement) is used according to IS:
1489-1991. Various tests were performed on cement
they are: Soundness test, Consistency test, Initial
and final setting time.

FIGURE: 2 Sanghi cement (53 grade PPC)
TABLE-2
PROPERTIES OF (PPC) CEMENT
Physical properties
of SANGHI
Cement (PPC) 53
grade


Result
Chemical
properties of
SANGHI Cement
(PPC) 53 grade


Result
(%)
Specific gravity 2.90 SiO
2
23.7
Standard
consistency (%)
31.6% Al
2
O
3
12.4
Initial setting time
(min)
210 min CaO 48.0
Final setting time
(min)
250 min MgO 1.83
Compressive
strength N/mm
2
at
28 days
52 N/mm
2
Fe
2
O
3
2.01
- - Loss on ignition 1.00

(c) Aggregate
Aggregate is a natural deposit of sand and
gravel and also give structure to the concrete. It
occupies almost 75% to 80% of volume in concrete
and hence shows influence on various properties
such as workability, strength, durability and
economy of concrete. To increase the density of
concrete aggregate is frequently use in different
sizes. Aggregate acts as reinforcement and introduce
strength to the overall composite material.
Aggregate is also used as base material for roads,
railroads and under foundation due to its good
strength.
(d) Coarse aggregate
The aggregate having size more than 4.75
mm is termed as coarse aggregate. The graded
coarse aggregate is described by its nominal size i.e.
40mm, 20mm, 16mm, 12.5mm etc. 80mm size is the
International Journal of Engineering Trends and Technology (IJETT) Volume 4 Issue 10 - Oct 2013
ISSN: 2231-5381 http://www.ijettjournal.org Page 4283

maximum size that could be conveniently used for
making concrete. In this study coarse aggregate is
conformed to IS: 383. The Flakiness and Elongation
Index were maintained well below 15%.

FIGURE: - 3 Coarse aggregate


FIGURE: - 4 Grit
(e) Fine Aggregate
Aggregate that pass through a 4.75 mm IS
sieve and having not more than 5 percent coarser
material are known as fine aggregate. Main function
of fine aggregate is to fill the voids in between
coarser particles and also helps in producing
workability and uniformity in mixture. In this study
fine aggregate is conform to IS: 383.

FIGURE: - 5 Fine Aggregate









TABLE-3
PROPERTIES OF FINE AND COARSE AGGREGATE
Property
Fine
Aggregate
Coarse Aggregate
Less than 20
mm
Less than 10
mm (Grit)
Fineness
modulus
3.30 7.52 3.20
Specific
gravity
2.38 2.76 2.69
Bulk density
(gm/cc)
1752 1744 1714
Water
absorption
(%)
1.25 1.80 1.36

f) Water
Water plays an important role as it
contributes in chemical reaction with cement. Water
is used for mixing as well as for curing purpose also
it should be clean and free from salts, acids, alkalis
and other harmful materials. Generally, ordinary
water is used for mixing concrete.
III. MIX DESIGN
As per IS: 10262-1982 mix design was
prepared for M25 grade and same design was used
in preparation of test samples.TABLE-4 shows mix
design proportion.
TABLE-4
MIX DESIGN PROPORTION FOR M25 grade
Water
(lit.)
Cement
(kg/m
3
)
Fine
Aggregate
(kg/m
3
)
Coarse
Aggregate
(kg/m
3
)
By weight
(gms)
191.60 479 485.75 1197.03
By volume
(m
3
)
0.40 1 1.01 2.50

TABLE-5
CONCRETE MIX DESIGN (M25 grade)
Sr
no.
Type of
concrete
Concrete mix design proportion
w/c
ratio
C FA CA WFS
1. B0 0.40 1 1.01 2.50 -
2. B2 0.40 1 0.81 2.50 0.20
3. B4 0.40 1 0.61 2.50 0.40
4. B6 0.40 1 0.41 2.50 0.60
C=Cement, FA=Fine Aggregate, CA=Coarse
Aggregate, WFS=Waste Foundry Sand





International Journal of Engineering Trends and Technology (IJETT) Volume 4 Issue 10 - Oct 2013
ISSN: 2231-5381 http://www.ijettjournal.org Page 4284

TABLE-6
LIST OF SYMBOL AND ABBREVIATION
Sr
no.
Type of concrete Fine aggregate replaced
by waste foundry sand
1. B0 Traditional concrete
2. B2 20% replacement
3. B4 40% replacement
4. B6 60% replacement

IV. EXPERIMENTAL METHODOLOGY
Concrete contains waste foundry sand as a
partial replacement of fine aggregate is tested.
Concrete is composed of cement, coarse aggregate,
fine aggregate, waste foundry sand and water. The
waste foundry sand is replaced in the range of 0%,
20%, 40% and 60% by weight of fine aggregate.
The mixture was prepared and three standard cubes
of 150*150*150 mm were casted. After curing for
24hrs the samples were demoulded and subjected to
compressive strength test and tensile split test for 7,
14 and 28 days.
(a) Compressive strength test
Compressive strength tests were performed
on compression testing machine of 2,000 KN
capacity. Three cubes of 150*150*150 mm from
each batch were subjected to this test. The
comparative study was made on properties of
concrete after percentage replacement of fine
aggregate by waste foundry sand in the range of 0%,
20%, 40% and 60%.

FIGURE: - 6 Compression strength test for cube










TABLE-7
COMPRESSIVE STRENGTH OF CUBES FOR M25 grade
AT 7, 14, 28 DAYS.
Type of
concrete
Average
ultimate
compressive
strength at
7 days
(N/mm
2
)
Average
ultimate
compressive
strength at 14
days (N/mm
2
)
Average
ultimate
compressive
strength at 28
days (N/mm
2
)
B0 27.70 30.81 37.93
B2 25.78 32.15 39.26
B4 25.90 32.30 39.70
B6 33.19 35.70 40.74



FIGURE: - 7 Graph of % replacement of waste foundry sand
v/s compressive strength (N/mm
2
) for 7, 14, 28 days.
(b) Split tensile test
The tensile strength of concrete is
approximately 10% of its compressive strength.
Tensile splitting strength tests of concrete block
specimens were determined as per IS: 5816-1999.
After curing of 28 days the specimens were tested
for tensile strength using a calibrated compression
testing machine of 2000 KN capacity.

FIGURE: - 8 Split tensile test for cube
International Journal of Engineering Trends and Technology (IJETT) Volume 4 Issue 10 - Oct 2013
ISSN: 2231-5381 http://www.ijettjournal.org Page 4285





TABLE-8
SPLIT TENSILE STRENGTH OF CUBE FOR M25 grade
AT 28 DAY.
Type of concrete Average ultimate split tensile
strength at 28 days (N/mm
2
)
B0 4.3
B2 3.61
B4 3.53
B6 3.15


FIGURE:-9 Graph of % replacement of waste foundry sand
v/s split tensile strength (N/mm
2
) for 28 days.
V. COST FEASABILITY
TABLE-9
MATERIALS COST
Sr no. Material Rate
(Rs/Kg)
1. Cement 6.00
2. Fine aggregate (sand) 0.60
3. Coarse aggregate (>20mm) 0.65
4. Grit 0.65
5. Foundry sand 0.15


TABLE-10
TOTAL COST OF MATERIALS FOR M25 grade PER m
3
.

CT Consumption of mix design proportions for
M25 grade
Total
cost/m
3

% cost
change
C F.A C.A G W.F.S
B0 479.00 485.75 718.22 478.81 0.00 3751.92 0
B2 479.00 388.60 718.22 478.81 97.15 3708.20 -1.16
B4 479.00 291.45 718.22 478.81 194.40 3664.50 -2.33
B6 479.00 194.30 718.22 478.81 291.45 3620.77 -3.50
CT=Concrete type, F.A=Fine Aggregate,
C.A=Coarse Aggregate, G=Grit, W.F.S=Waste
Foundry Sand.


VI. CONCLUSION
Based on above study the following
observations are made regarding the properties and
behaviour of concrete on partial replacement of fine
aggregate by waste foundry sand:
(1) Compressive strength increases on increase in
percentage of waste foundry sand as compare to
traditional concrete.
(2) In this study, maximum compressive strength is
obtained at 60% replacement of fine aggregate by
waste foundry sand.
(3) Split tensile strength decrease on increase in
percentage of waste foundry sand.
(4) Use of waste foundry sand in concrete reduces
the production of waste through metal industries i.e.
its an eco-friendly building material.
(5) The problems of disposal and maintenance cost
of land filling is reduced.
(6) Application of this study leads to develop in
construction sector and innovative building material.
(7) The result of percentage cost change reduces up
to 3.5 for 60% replacement of waste foundry sand.
This shows that the concrete produced is
economical.
ACKNOWLEDGMENTS
The author thankfully acknowledge to Asst. Prof.
Jayeshkumar Pitroda, B.V.M. Engineering College,
Asst. Professor Patel Ankit, Asst. Professor Rajgor
Mamta, Lab Asst. Dinubhai .G .Desai Asst.
Professor Jasmini Khatri (HOD), Sigma Institute of
Engineering, Vadodara, Gujarat.
REFERENCES
[1] Abichou T. Benson, C. Edil T., 1998a.Database
on beneficial reuse of foundry by- products.
Recycled materials in geotechnical applications,
Geotech. Spec. Publ.No.79, C. Vipulanandan and
D.Elton, eds., ASCE, Reston, Va., 210-223
[2] Assistant Prof. Ankit .N. Patel, Assistant Prof.
Jayeshkumar.Pitroda stone waste as a
groundbreaking conception for the low cost concrete
,ISSN No-2231-5381,Vol IV, Issue IV, April 2013,
Pg no 843-849.

International Journal of Engineering Trends and Technology (IJETT) Volume 4 Issue 10 - Oct 2013
ISSN: 2231-5381 http://www.ijettjournal.org Page 4286

[3] Bemben, S.M., Shulze, D.A., 1993.The influence
of selected testing procedures on soil/geomembrane
shear strength measurements. Proc.,
Geosynthetics93, Industrial Fabrics Association
International, St.Paul, Minn., 619-631.
[4] Bemben, S.M., Shulze, D.A., 1995.The influence
of testing procedures on clay/geomembrane shear
strength measurements. Proc. Geosynthetics 95,
IFAI, St.Paul, Minn., 1043-1056.
[5] D.Lawrence and M. Mavroulidou, (2009)
Properties of Concrete Containing Foundry Sand,
London.
[6] Dushyant Rameshbhai Bhimani, (2013) Used
Foundry Sand: Opportunities for Development Of
Eco-Friendly Low Cost Concrete, IJAET/Vol. IV/
Issue I/Jan.-March., 2013/63-66, Vallabh
Vidyanagar, Gujarat, India.
[7] Eknath P. Salokhe, D.B.Desai, Application of
Foundry Waste Sand in Manufacture of Concrete.
Kolhapur, India.
[8] Hiren A. Rathod, (2013) An Experimental
Investigation on Utilization of Various Wastes In
The Lean Concrete Blocks, IJAERS/Vol. II/ Issue
III/April-June, 2013/106-109, Vallabh Vidyanagar,
Gujarat, India.
[9] IS: 383-1970, Specifications for coarse and fine
aggregates from natural sources for concrete,
Bureau of Indian Standards, New Delhi, India.
[10] IS: 10262-1982, recommended guidelines for
concrete mix design, Bureau of Indian Standards,
New Delhi, India.
[11] IS: 1489-1991, Specifications for 53-Grade
Portland Pozzolana cement, Bureau of Indian
Standards, New Delhi, India.
[12] IS: 516-1959, Indian standard code of practice-
methods of test for strength of concrete, Bureau of
Indian Standards, New Delhi, India.
[13] IS: 5816-1999, Indian standard code for
splitting tensile strength of concrete method of
test, Bureau of Indian Standards, New Delhi, India.
[14] Saveria Monosi, Daniela Sani and Francesca
Tittarelli, (2010) Used Foundry Sand in Cement
Mortars and Concrete Production, The Open Waste
Management Journal, 2010, 3, 18-25, Italy.
[15] Tarun R. Naik, Viral M. Patel, Dhaval M.
Parikh, and Mathew P. Tharaniyil, Utilization Of
Used Foundry Sand In Concrete, University Of
Wisconsin Milwaukee.
[16] Tikalsky, J. Paul, Smith, Earl and Regan, W.
Raymond, December 1998. Proportioning Spent
Casting Sand In Controlled Low-Strength Materials.
Aci Material Journal, V.95, No.6, Pp 740-746.