International Journal of Computer Trends and Technology (IJCTT) volume 8 number 4 Feb 2014

ISSN: 2231-2803 http://www.ijcttjournal.org Page178

Implementation of Minutiae Based Fingerprint Identification System using
Crossing Number Concept
Atul S. Chaudhari
#1
, Dr. Girish K. Patnaik*
2
, Sandip S. Patil
+3
#1
Research Scholar, *
2
Professor and Head,
+3
Associate Professor
#1
(Department of Computer Engineering, SSBTs College of Engineering & Technology, Bambhori, Jalgaon [M. S.], INDIA)
*
2
(Department of Computer Engineering, SSBTs College of Engineering & Technology, Bambhori, Jalgaon [M. S.], INDIA)
+3
(Department of Computer Engineering, SSBTs College of Engineering & Technology, Bambhori, Jalgaon [M. S.], INDIA)

Abstract: Biometric system is essentially a pattern
recognition system which recognizes a person by determining
the authenticity of a specific physiological (e.g., fingerprints,
face, retina, iris) or behavioral (e.g., gait, signature)
characteristic possessed by that person. Among all the
presently employed biometric techniques, fingerprint
identification systems have received the most attention due to
the long history of fingerprints and its extensive use in
forensics. Fingerprint is reliable biometric characteristic as it
is unique and persistence. Fingerprint is the pattern of ridges
and valleys on the surface of fingertip. However, recognizing
fingerprints in poor quality images is still a very complex job,
so the fingerprint image must be preprocessed before
matching. It is very difficult to extract fingerprint features
directly from gray scale fingerprint image. In this paper we
have proposed the system which uses minutiae based
matching algorithm for fingerprint identification. There are
three main phases in proposed algorithm. First phase enhance
the input fingerprint image by preprocessing it. The enhanced
fingerprint image is converted into thinned binary image and
then minutiae are extracted by using Crossing Number
Concept (CN) in second phase. Third stage compares input
fingerprint image (after preprocessing and minutiae
extraction) with fingerprint images enrolled in database and
makes decision whether the input fingerprint is matched with
the fingerprint stored in database or not.
Keywords: Fingerprint Identification, Minutiae Extraction,
Crossing Number Concept.
1. INTRODUCTION
In the field of biometric identification, fingerprints are the
most widely used biometric feature for person identification
and verification. The fingerprint of every individual is
considered to be unique. No two persons have the same set of
fingerprints; also finger ridge patterns do not change
throughout the life of an individual. This property makes
fingerprints an excellent biometric identifier. Therefore it is
one of the popular and effective means for identification of an
individual and used as forensic evidence. In recent years,
significant performance improvements have been achieved in
commercial automatic fingerprint recognition systems.
Biometric Systems are systems that use distinctive
anatomical (e.g., fingerprints, face, iris) and behavioral (e.g.,
speech) characteristics, called biometrics traits, to
automatically recognize individuals. The word biometrics is
derived from the Greek words bios (meaning life) and metron
(meaning measurement); biometric identifiers are
measurements from living human body [3]. Perhaps all
biometric identifiers are a combination of anatomical and
behavioral characteristics and they should not be exclusively
classified into either anatomical or behavioral characteristics.
For example, fingerprints are anatomical in nature but the
usage of the input device depends on the persons behavior.
Thus, the input to the recognition engine is a combination of
anatomical and behavioral characteristics.
Fingerprints are the patterns formed on the epidermis
of the fingertip. Fingerprints are made up of series of ridges
and valleys (also called as furrows) on the surface of the
fingertip and have core around which pattern like swirls, loops
or arches are curved to ensure that each print is unique [3].
Fingerprint is composed of ridges and valleys. The interleaved
pattern of ridges and valleys are the most evident structural
characteristic of a fingerprint. The ridges are the single curved
segment and valleys are the region between two ridges. The
most commonly used fingerprint features are minutiae.
Minutiae are the discontinuities in local ridge structure. They
are used by forensic experts to match two fingerprints. There
are about 150 different types of minutiae [7]. Among these
minutiae types ridge ending and ridge bifurcation are the
most commonly used as all the other types of minutiae are
combinations of ridge endings and ridge bifurcations. A ridge
ending is defined as the ridge point where a ridge ends
abruptly [3]. A ridge bifurcation is defined as the ridge point
where a ridge forks or diverges into branch ridges [3]. Some
common types of minutiae are shown in fig. 1

Fig 1: Types of minutiae.

International Journal of Computer Trends and Technology (IJCTT) volume 8 number 4 Feb 2014
ISSN: 2231-2803 http://www.ijcttjournal.org Page179

2. RELATED WORK

Lili Liu and Tianjie Cao proposed an efficient verification
system based on biometrics. In this systemthey have used
Gabor filter based Enhancement and CN concept for Minutiae
Extraction [1].
Lin Hong et al. have designed and implemented an
Identity Authentication systemwhich operates in two stages:
minutiae extraction and minutiae matching. An alignment-
based elastic matching algorithmis proposed for minutiae
matching [9].
Manvjeet Kaur et al. proposed Fingerprint
Verification System using Minutiae Extraction Technique. In
this Systemthey have introduced combined methods to build
a minutia extractor and a minutia matcher. Segmentation with
Morphological operations used to improve thinning, false
minutiae removal, minutia marking. For this system they have
used Histogram Equalization and FFT for fingerprint image
enhancement and CN Concept for Minutiae Extraction [8].
F. A. Afsar et al. presented the minutiae based
Automatic Fingerprint Identification Systems. The technique
is based on the extraction of minutiae from the thinned,
binarized and segmented version of a fingerprint image. The
system uses fingerprint classification for indexing during
fingerprint matching which greatly enhances the performance
of the matching algorithm[5].
Ishpreet Singh Virk and Raman Maini have used
histogram equalization for fingerprint image enhancement,
segmentation using Morphological operations, minutia
marking by specially considering the triple branch counting,
branch into three terminations, an alignment-based elastic
matching algorithmminutia unification by decomposing has
been developed for minutia matching were implemented. The
proposed alignment- based elastic matching algorithm is
capable of finding the correspondences between minutiae
without resorting to exhaustive search [10].
Weiping Chen and Yongsheng Gao presented a new
minutiae-based fingerprint matching algorithmusing phase
correlation. They define a new representation called Minutiae
Direction Map (MDM). First, they convert minutiae sets into
2D image spaces. Then the transformation parameters are
calculated using phase correlation between two MDMs to
align two fingerprints to be matched. The similarity of two
fingerprints is determined by the distance between two
minutiae sets [11].
Anil Jain et al. develop a matcher that utilizes Level
3 features, including pores and ridge contours, for 1000dpi
fingerprint matching. Level 3 features are automatically
extracted using wavelet transformand Gabor filters and are
locally matched using the ICP algorithm. Their experiments
on a median-sized database show that Level 3 features carry
significant discriminatory information. EER values are
reduced (relatively 20%) when Level 3 features are
employed in combination with Level 1 and 2 features [12].
Thrust literature survey and review concludes that
existing methods are not only facing problems of poor quality
fingerprint image but also their dataset dependency.


Table 1: Literature Review



Authors Techniques/Al
gorithms Used
FAR,
FRR and
VR
D/B Used Accu
racy
Compu
tation
Time
Lili Liu and
Tianjie Cao
(2012)[1]
Gabor filter
based
Enhancement
and CN
concept for
Minutiae
Extraction
FAR=
0.085%
FRR=
1.4%
VR=
99.75%
2000
fingerprint
images of 200
individuals at
500dpi
size: 256360
N/A N/A
Lin Hong,
Anil Jain,
Sharath
PanKanti
and R.
Bolle
(1997) [9]
Alignment
based elastic
matching
algorithm
FRR=
15%
MSU: contain
10 images per
finger from70
individuals.
Total 700
images
size: 640480
High 1.4 sec.
on Sun
ULTR
A 1
Work
station
Manvjeet
Kaur,
Mukvinder
Singh and
Parvinder S.
Sindhu
(2008) [8]
Histogram
Equalization
and FFT for
enhancement
and CN
Concept for
Minutiae
Extraction
VR=
75%
N/A N/A N/A
F. A. Afsar,
M. Arif and
M. Hussain
(2004) [5]
Gabor filter
based
Enhancement
and CN
concept for
Minutiae
Extraction
FAR=
1%
FRR=
7%
EER=
5%
FVC 2000
800
fingerprints
from110
different
fingers
High
92%
12 sec.
Ishpreet
Singh Virk
and Raman
Maini
(2012) [10]
Histogram
Equalization
for
enhancement
and CN
Concept for
Minutiae
Extraction
FAR=
0.06%
FRR=
6.9%
FVC2000 N/A N/A
Weiping
Chen and
Yongsheng
Gao
(2007)[11]




Fingerprint
Matching
Algorithm
Using Phase
Correlation
EER=
2.44%
Total 400
fingerprints,
which consists
of 100 fingers
and 4
impressions
per finger
size: 260
300
N/A N/A
Anil Jain,
Yi Chen,
and Meltem
Demirkus
(2007)[12]
Fingerprint
Matching
Using Level 3
Features
(LCP algorithm
for matching
level 3
features)
EER=
4.9%
1000dpi (slap)
fingerprint
impressions of
410 different
fingers
(41 subjects
10 fingers per
subject)
High N/A
International Journal of Computer Trends and Technology (IJCTT) volume 8 number 4 Feb 2014
ISSN: 2231-2803 http://www.ijcttjournal.org Page180

3. PROPOSED SYSTEM
In real world environment, for fingerprint identification it is
not always possible to provide idle quality fingerprint image
and also it not possible to provide homogeneous dataset.
These major challenges in fingerprint identification is
accepted and overcome in proposed system.
Proposed fingerprint identification systemis mainly
divided into three modules like fingerprint image
preprocessing, minutiae extraction and minutiae matching as
shown in fig.2. The input fingerprint image is processed for
skeleton image by the fingerprint image preprocessing stage
and subsequently processed by minutiae extraction stage for
extracting minutiae using crossing number concept. After
minutiae extraction stage if input fingerprint image is
processed for enrollment then the skeleton image is saved as
template fingerprint image in database, otherwise skeleton
image is given to matching stage. In matching stage system
compares skeleton image with template fingerprint images
fromdatabase and make decision whether input fingerprint
matched or not.


Fig 2: Work Flow Diagramof Proposed Fingerprint
Identification System.

The working of proposed systemis as follows:
Step 1: Load the input fingerprint image.
Step 2: Performnormalization on the input fingerprint image
to standardize the intensity values in fingerprint image.
Step 3: Performsegmentation using Variance Thresholding
method on Normalize fingerprint image to separate
foreground region and background region.
Step 4: Next, enhance the fingerprint image using Gabor
filter.
Step 5: After enhancement convert the image into binary
image using global threshold of zero method.
Step 6: Performthinning operation on binary image to create
skeletonised version of the binary image.
Step 7: Extract minutiae from thinned image using crossing
number concept and go to step 8 if input fingerprint image is
processed for enrollment otherwise go to step 9 if it is
processed for identification.
Step 8: If input fingerprint image is processed for enrollment
then enroll it into database.
Step 9: Use minutiae based algorithm to match input
fingerprint image with all template images stored in database
if matching is successful then fingerprint is identified, display
information related to matched fingerprint otherwise it is not
identified.
The main modules of proposed systemare explained
in following sections.

0.1. Normalization
In this stage normalization is performed on input fingerprint
image. Normalization is used to standardize the intensity
values in fingerprint image by adjusting the range of grey-
level values so that it lies within a desired range of values. Let
I (i, j) represent the grey-level value at pixel (i, j), and N (i, j)
represent the normalized grey-level value at pixel (i, j). The
normalized image is defined as [5]:
N(i,]) =

H
0
+
_
I
0
(I(i,]) H)
2
I
i I(i,]) >H,
H
0

_
I
0
(I(i,]) H)
2
I
otcrwisc,
(1)
where M and V are the estimated mean and variance of I(i; j),
respectively, and M0 and V0 are the desired mean and
variance values, respectively.

0.2. Segmentation
Segmentation is the process of separating the foreground
regions in the image from the background regions. In
fingerprint image the foreground regions correspond to the
fingerprint area containing the ridges and valleys, which is our
area of interest and background corresponds to the regions
outside the borders of the fingerprint area, which do not
contain any valid fingerprint information. When minutiae
extraction algorithms are applied to fingerprint image due to
the background regions of an image, extraction algorithm
extract noisy and false minutiae. Therefore in this stage
segmentation is employed to discard these background
regions, which facilitates the reliable extraction of minutiae.
In a fingerprint image, the background regions generally
exhibit a very low grey-scale variance value, whereas the
foreground regions have a very high variance. Hence a
International Journal of Computer Trends and Technology (IJCTT) volume 8 number 4 Feb 2014
ISSN: 2231-2803 http://www.ijcttjournal.org Page181

method based on variance Thresholding [7] is used to perform
the segmentation. Firstly, the image is divided into blocks and
the grey-scale variance is calculated for each block in the
image. If the variance of block is less than the global
threshold, then the block is assigned to be a background
region; otherwise, it is assigned to be part of the foreground.
The grey-level variance for a block of size WW is calculated
as:
I(k) =
1
w
2

w-1
=0

w-1
]=0
(I(i,]) H(k))
2
(2)

where V(k) is the variance for block k, I(i, j) is the grey-level
value at pixel (i, j), and M(k) is the mean grey-level value for
the block k.

3.3. Fingerprint Image Enhancement
In this stage fingerprint image is enhanced using method
employed by Hong et al. [7] The configuration of parallel
ridges and valleys with well-defined frequency and orientation
in a fingerprint image provide useful information which helps
in removing undesired noise. Gabor filters have both
frequency-selective and orientation-selective properties and
have optimal joint resolution in both spatial and frequency
domains. Therefore, it is appropriate to use Gabor filters as
band pass filters to remove the noise and preserve true
ridge/valley structures.

3.4. Binarisation
Most minutiae extraction algorithms operate on binary images
where there are only two levels of interest: the black pixels
that represent ridges, and the white pixels that represent
valleys. Binarisation is the process that converts a grey level
image into a binary image. This improves the contrast
between the ridges and valleys in a fingerprint image, and
consequently facilitates the extraction of minutiae.
In this stage grayscale fingerprint image is converted
into binary image using a global threshold. [4] The
binarisation process involves examining the grey-level value
of each pixel in the enhanced image and if the value is greater
than the global threshold, then the pixel value is set to a binary
value one; otherwise, it is set to zero. The outcome is a binary
image containing two levels of information, the foreground
ridges and the background valleys.
Let I (x, y) represent the intensity value of enhanced
grayscale image at pixel position (x, y). Let Tp be the
threshold value. In case of fingerprint images Tp represents
the differentiating intensity between the background pixels
and ridge pixels. BW(x, y) represent the binary image
obtained by the equation.
Bw(x,y) =_
1, i I(x,y) I
p
0, 0tcrwisc
(S)



3.5. Thinning
In this stage thinning operation is performed on binary image
to create skeletonised version of the binary image. Thinning is
a morphological operation that successively erodes away the
foreground pixels in binary image until they are one pixel
wide[2]. A standard thinning algorithmis employed, which
performs the thinning operation using two sub-iterations. This
algorithmis accessible in MATLAB via the thin operation
under the bwmorph function. [2] The skeleton image is then
used in the subsequent extraction of minutiae.

3.6. Minutiae Detection
The most commonly employed method of minutiae extraction
is the Crossing Number (CN) concept. This method involves
the use of the skeleton image where the ridge flow pattern is
eight-connected. The minutiae are extracted by scanning the
local neighborhood of each ridge pixel in the image using a
33 window. The CN value is then computed, which is
defined as half the sumof the differences between pairs of
adjacent pixels in the eight-neighborhood. According to
Rutovitz the CN for a ridge pixel P is given by: [6][10]

CN =
1
2
|P

P
-1
|, P
9
= P
1
8
=1
(4)

where Pi is the pixel value in the neighborhood of P. For a
pixel P, its eight neighbouring pixels are scanned in an anti-
clockwise direction as follows:

P
4
P
3
P
2

P
5
P P
1

P
6
P
7
P
8

Fig 3: 33 window for searching minutiae [6] [10]
After the CN for a ridge pixel has been computed, the
pixel can then be classified according to the property of its CN
value. Using the properties of the CN as shown in Table 2, the
ridge pixel can then be classified as a ridge ending, bifurcation
or non-minutiae point. For example, a ridge pixel with a CN
of one corresponds to a ridge ending, and a CN of three
corresponds to a bifurcation.

Table: 2 Properties of Crossing Number [6] [10]
CN Property
0 Isolated Point
1 Ridge Ending Point
2 Continuing Ridge Point
3 Bifurcation Point
4 Crossing Point

International Journal of Computer Trends and Technology (IJCTT) volume 8 number 4 Feb 2014
ISSN: 2231-2803 http://www.ijcttjournal.org Page182

3.7. Minutiae Matching

Let T and I be the representation of the template and input
fingerprint, respectively. Each minutia is considered as a
triplet m = {x, y, } that indicates the x, y minutia location
coordinates and the minutia angle :
T ={m
1,
m
2,
m
3..
m
m
}, m
i
={x
i
, y
i
,
i
} , i=1,2m
I ={m
1,
m
2,
m
3 ..
m
n
}, m
j
={x
j
, y
j
,
j
} , j=1,2n
where mand n denote the number of minutiae in T and I,
respectively.
A minutia m
j
in I and a minutia m
i
in T are
considered matching, if the spatial distance (sd) between
themis smaller than a given tolerance r
0
and the direction
difference (dd) between them is smaller than an angular
tolerance
0.
[3]

4. EXPERIMENTAL RESULTS
The proposed systemis implemented using MATLAB 7.10
(R2010a) and tested on database which is contains total 440
fingerprint images out of which 160 images are fromFVC
2000 (DB1 and DB2)[13], 160 images are fromFVC 2002
(DB1 and DB2)[14] and 120 fingerprint images (size
260300) are scanned using SecuGen Hamster plus. This
scanner employs a high-performance and maintenance-free
optical sensor. To evaluate the performance of proposed
system FAR and FRR of proposed system are calculated.
Table 2 shows the FAR and FRR of proposed fingerprint
identification system. At first we have enrolled 440 fingerprint
images in database, and then to calculate FRR of the proposed
system we have tested the system by giving 440 input
fingerprint images for identification. The systemis also tested
by giving 200 imposter fingerprint images as input.

Table: 3 Performance Evaluation of Proposed System.
Enrolled
Fingerprints
Imposter
Fingerprints
Input test Fingerprints 440 200
Accepted Fingerprints 439 0
Rejected Fingerprints 1 200
FRR=0.23% FAR=0%

Fig 4 shows experimental results of various stages in proposed
system. Fig 4(a) shows original images, Fig 4(b) shows
fingerprint image after normalization, Fig 4(c) shows
fingerprint image after segmentation using variance
Thresholding, Fig 4(d) shows resulting fingerprint image after
enhancement using Gabor filter Fig 4(e) shows result if
binarisation using global threshold, Fig 4(f) shows skeleton
image after applying thinning operation on binary image and
Finally Fig 4(g) shows extracted minutiae using Crossing
Number method.


(a) Original image (b) Normalized image

(c) Segmented image (d) Enhanced image

(e) Binary image (f) Thinned image

(g) Minutiae Extracted Using CN Concept
Fig: 4 Experimental results in various stages of proposed
system
V. CONCLUSIONS AND FUTURE WORK
The performance of a fingerprint feature extraction and
matching algorithms heavily depends upon the quality of the
input fingerprint image. Gabor filters has both frequency
selective and orientation-selective properties. It is observed
that Gabor filter method of fingerprint image enhancement is
International Journal of Computer Trends and Technology (IJCTT) volume 8 number 4 Feb 2014
ISSN: 2231-2803 http://www.ijcttjournal.org Page183

giving better results. Minutiae extraction algorithmcan detect
all the minutiae, including both true and false minutiae, using
the Rutovitz Crossing Number (CN) on the skeleton images
after thinning stage. The performance of proposed system is
evaluated by calculating FAR and FRR. The proposed system
has 0% FAR and 0.23% FRR which shows that the accuracy
of proposed systemis high. The proposed system is simulated
on 2.30 GHz Intel core i5 general purpose system using
MATLAB 7.10. The proposed minutiae based fingerprint
identification shows better performance in identifying the
fingerprint, till it takes more time. The time required for
detection and recognition could considerable be reduced by
implementing the same systemon dedicated hardware using
low or middle level language such as C and C++. In future, we
will try to implement the same systemusing C language. Also
it is observed that thinning process sometime breaks the ridges
which results in increasing number of false minutiae so there
is scope to improve thinning algorithm so that it will reduce
number of false minutiae and increase accuracy of the system.


REFERANCES
[1] Lili Liu and Tianjie Cao, The Research and Design of an
Efficient Verification System Based on Biometrics,
International Conference on Computer Science and Electrical
Engineering, 2012.

[2] Dr. Salah M. and Dr. Feryal I. Haj Hassan, Fingerprint
Minutiae Extraction, Journal of Computing Press., Vol. 2,
November 2010.

[3] Maltoni D., Maio D., Jain A. K., and Prabhakar S.
Handbook of Fingerprint Recognition. Springer, 2003.

[4] Lavanya B. N., K. B. Raja and Venugopal K. R.,
Minutiae Extraction in Fingerprint using Gabor Filter
Enhancement, International Conference on Advances in
Computing, Control and Telecommunication Technologies,
IEEE, 2009.

[5] F. A. Afsar, M. Arif and M. Hussain, Fingerprint
Identification and Verification System using Minutiae
Matching, National Conference on Engineering
Technologies, 2004.

[6] Feng Zhao and Xiaoou Tang, Preprocessing and
postprocessing for skeleton-based fingerprint minutiae
extraction, Pattern Recognition Society, Published by
Elsevier Ltd, 2006.

[7] L. Hong, Y. Wan and A. Jain, "Fingerprint Image
Enhancement: Algorithm and Performance Evaluation, IEEE
Pattern Analysis and Machine Intelligence, vol. 20, No. 8, pp.
777-787, 1998.

[8] Manvjeet Kaur, Mukvinder Singh and Parvinder S.
Sindhu, Fingerprint Verification System using Minutiae
Extraction Technique, Proceedings of World Academy of
Science, Engineering and Technology, vol. 36, December
2008.

[9] Lin Hong, Anil Jain, Sharath PanKanti and R. Bolle,
Identity Authentication Using Fingerprints, Proceedings of
the IEEE, Vol. 85, September1997.

[10] Ishpreet Singh Virk and Raman Maini, Fingerprint
Image Enhancement and Minutiae Matching in Fingerprint
Verification, Journal of Computing Technologies, vol. 1,
June 2012.

[11] Weiping Chen and Yongsheng Gao, A Minutiae-based
Fingerprint Matching Algorithm Using Phase Correlation,
Digital Image Computing Techniques and Applications, IEEE,
2007.

[12] Anil Jain, Yi Chen, and MeltemDemirkus, Pores and
Ridges: Fingerprint Matching Using Level 3 Features, 2007.

[13] Fingerprint Verification Competition (FVC2000)
http://bias.csr.unibo.it/fvc2000/

[14] Fingerprint Verification Competition (FVC2002)
http://bias.csr.unibo.it/fvc2002/

[15] Mary Lourde R. and Dushyant Khosla, Fingerprint
Identification in Biometric Security Systems, International
Journal of Computer and Electrical Engineering, vol. 2, No.
5, October 2010.

[16] Ravi J., K. B. Raja and Venugopal K. R., Fingerprint
Recognition using Minutia Score Matching, International
Journal of Engineering Science and Technology, vol. 1(2),
2009.

[17] A. K. J ain, A. Ross, and S. Prabhakar, An introduction
to biometric recognition", IEEE Transaction on Circuits and
Systems for Video Technology, vol. 14, no. 1, pp. 4-20,
January 2004.