C200HW-PA204, C200HW-PA204S,

C200HW-PA204R, C200HW-PA209R,
C200HW-PD24
OMRON
SYSMAC - System C200H Power Supplies

Note Use either the C200HW-COM01 or a V1 Communications Board for the ZE-ver-
sion C200HX/HG/HE CPU Units.
Indicators (LEDs) The Communications Board indicators on the front panel of the CPU Unit indi-
cate the status of the Board, as described in the following table.
Indicator CoIor Status Meaning
RDY Green Not lit The Board cannot be used due to a hardware
error on the Board.
Flashing A setting error has been discovered in the PC
Setup or the protocol data.
Lit The Board is operating properly and
communications are possible.
COMB Orange Flashing Communications are in progress with the
device connected to port B.
COMA Orange Flashing Communications are in progress with the
device connected to port A.
2-2-4 Power SuppIy Units
Power Supply Units provide power to the CPU Rack and the Expansion /O
Racks. Power Supply Units are available for either AC or DC power input. The
numbers in the diagram correspond to the numbers of the following items in the
description. (The following diagram shows the C200HW-PA204S.)
Part Names and Functions
2. Terminals for external
connections
1. POWER indicator
100 to 120 VAC/
200 to 240 VAC
100 to 120
200 to 240
+24 VDC 0.8 A
L
2
/N
L
1
Note The AC input terminals may
be indicated as L
1
/N and L
2
instead of L
2
/N and L
1
on
some Units. However, there
is no difference in their func-
tions or performance.
L
2
/N
L
1
L
1
/N
L
2
1. POWER Indicator
The POWER indicator will be lit whenever the Power Supply Unit is output-
ting 5 V.
-
Section 2-2

2. TerminaIs for ExternaI Connections

These terminals are connected as shown in the diagram below. The num-
bers in the diagramcorrespond to the numbers of the following items in the
description.
SuppIy
voItage
Output
capacity
Output
terminaIs
RUN output ModeI
100 to
120 VAC or
200 t
5 VDC, 4.6 A,
30 W
Without Without C200HW-PA204
200 to
240 VAC
(Select the
voltage using
24 VDC,
0.8 A
Without C200HW-PA204S
voltage using
the metal
short bar on
Without With C200HW-PA204R
short bar on
the voltage
selector
terminals.)
5 VDC, 9 A,
45 W
Without With C200HW-PA209R
24 VDC 5 VDC, 4.6 A,
30 W
Without Without C200HW-PD024
-
Section 2-2

TerminaI Connections
1. AC nput
2. Voltage selector
terminals
3. LG
4. GR
C200HW-PA204: AC Input C200HW-PA204S: ACInput
100 to 120 VAC/
200 t o 240 VAC
L2/N
L1
1. AC nput
3. LG
4. GR
5. 24 VDC output
100 to 120 VAC/
200 t o 240 VAC
24 VDC 0.8 A
L2/N
L1
2. Voltage selector
terminals
nput
100 to 120
Close
200 t o 240
Open
nput
100 t o 120
Close
200 t o 240
Open
Output NC
1. AC nput
2. Voltage selector
terminals
3. LG
4. GR
7. RUN output
6. DC nput
3. LG
4. GR
C200HW-PA204R: AC Input
C200HW-PD024: DCInput
100 to 120 VAC/
200 t o 240 VAC
RUN OUTPUT
250 VAC
24 VDC
2 A
24 VDC
L2/N
L
1
C200HW-PA209R: DC Input
1. AC nput
2. Voltage selector
terminals
3. LG
4. GR
7. RUN output
RUN OUTPUT
240 VAC
24 VDC
2 A Resistive
100 to 120 VAC/
200 t o 240 VAC
L2/N
L1
nput nput
100 t o 120
Close
200 t o 240
Open
100 t o 120
Close
200 t o 240
Open
1. AC Input (C200HW-PA20 OnIy)
Supply either 100 to 120 VAC or 200 to 240 VAC to the AC input terminals. f
one power supply phase of the equipment is grounded, connect the
grounded phase side to the L
2
/N (or L
1
/N if so indicated) terminal.
2. VoItage SeIector TerminaIs (C200HW-PA20 OnIy)
Short these terminals with a metal short bar when 100 to 120 VAC is being
supplied to the AC input terminals.
3. LG
Ground the LGterminal to 100 or less to increase resistance to noise and
protect against possible electrical shock.
-
Section 2-2

4. GR
Ground the GR terminal to 100 or less to protect against possible electri-
cal shock.
5. 24 VDC Output (C200HW-PA204S OnIy)
The 24 VDC output terminals can be used to supply power to DC nput Units.
The combined power consumption for both 5 V and 24 V must be 30 W or
less.
6. DC Input (C200HW-PD024 OnIy)
Supply 24 VDC to the DC input terminals.
7. RUN Output (C200HW-PA204R/PA209R OnIy)
The internal contact will turn ON when the CPU Unit is operating in RUN or
MONTOR mode. These terminals are available only on the C200HW-
PA204R.
-
Section 2-2
!

Use the C200HW-PA204R/PA209R Power Supply Unit only with the following
CPU Units and Backplanes. CPU Units and Backplanes with manufacturing
numbers earlier than the ones given cannot be used.
CPU Units
ModeI Manufacturing number (See beIow.)
Made in Japan Made in the NetherIands
C200HX-CPU65-E 20Z6 or later 0147 or later
C200HX-CPU54-E 2817 or later
C200HX-CPU44-E 19Z6 or later
C200HX-CPU34-E 2417 or later
C200HG-CPU63-E 25Z6 or later
C200HG-CPU53-E 0817 or later
C200HG-CPU43-E 19Z6 or later
C200HG-CPU33-E 1017or later
C200HE-CPU42-E 20Z6 or later
C200HE-CPU32-E 19Z6 or later
C200HE-CPU11-E 20Z6 or later
C200HX/HG/HE-
CPU -ZE
All models
BackpIanes (with C200HW-PA204R)
ModeI Manufacturing number (See beIow.)
Made in Japan Made in the NetherIands
C200HW-BC031 0617 or later 0147 or later
C200HW-BC051 19Z6 or later
C200HW-BC081 24Z6 or later
C200HW-BC101 20Z6 or later
BackpIanes (with C200HW-PA209R)
CPU BackpIanes I/O BackpIanes
C200HW-BC031 Same
manufacturing
C200HW-B031 Same
manufacturing
C200HW-BC051
manufacturing
number as for
C200HW-PA204R.
C200HW-B051
manufacturing
number as for
C200HW-PA204R.
C200HW-BC081-V1 (-V1 or later) C200HW-B081-V1 (-V1 or later)
C200HW-BC101-V1 (-V1 or later) C200HW-B101-V1 (-V1 or later)
Caution When using the C200HW-PA209R Power Supply Unit, be sure to use only the
Backplanes listed in the above table. Using a different Backplane may result in
malfunction due to deterioration of the base or pattern burnout.
Note Manufacturing numbers are as shown in the following diagram.
Year (Ex. 1997 = 7)
Month (1 to 9 = Jan to Sep, X/Y/Z = Oct/Nov/Dec
Day (01 to 31)
Restrictions for the
C200HW-PA204R/PA209R
-
Section 2-2

2-2-5 BackpIanes
There are two types of Backplane: the CPU Backplane, used for the CPU Rack,
and the /O Backplane, used for Expansion /O Racks. The Backplane serves to
hold and connect the following types of Unit: the CPU Unit, the Power Supply
Unit, /O Units, Special /O Units, etc.
The components of the Backplanes are shown in the following diagrams and
described following them. The numbers in the diagram correspond to the num-
bers of the following items in the description.
CPU BackpIane
1. Backplane
mounting
screw
2. Power Supply
Unit connector
3. CPU Unit
connector
4. Unit mounting slots
5. Unit connector
6. Unit lock levers
7. /OConnecting Cable connector
I/O BackpIane
4. Unit mounting slots
5. Unit connector 6. Unit lock levers
7. /OConnecting Cable connector
1. Backplane
mounting
screw
2. Power Supply
Unit connector
1. BackpIane Mounting Screws
Mount the Backplane firmly using four M4 screws.
2. Power SuppIy Unit Connector
Connect the Power Supply Unit.
3. CPU Unit Connector
Connect the CPU Unit.
4. Unit Mounting SIots
Mount one Unit to each slot. There are 3, 5, 8, or 10 slots available on the
Backplane depending on the model of Backplane used.
5. Unit Connectors
Connect /O Units, Special /O Units, nterrupt nput Units, and/or Analog
Timer Units.
Note Attach a C500-COV01 Connector Cover to any slot that is not being used to pre-
vent dust and dirt from entering the unused connectors.
6. Unit Lock Levers
The lock levers hold the Units in place. Press down on the level and pull up
on the Unit to release the lock.
7. I/O Connecting CabIe Connector
Connect the /OCable fromthe CPU Rack to the first Expansion /ORack or
between adjacent Expansion /O Racks to this connector.
-
Section 2-2