A (Very) Short Course in Internal Ballistics

Internal ballistic, or the science of what goes on inside of the gun, is a very complicated topic. This page is
not designed to give you a degree in the field but rather to provide some background data to help you
understand the subject.
Fr. Frog's Rules of Internal Ballistics
1) There ain't no magic powders!
2) There are no magic cartridge cases!
3) Details! It's in the details.
4) Inconsequential increments are meaningless.
5) Most gun writers are pathological liars.
Definition of Terms
Barrel Length - In interior ballistic work this differs from the "barrel length" use in general
measurements. It is measured from the face of the muzzle to the base of the seated bullet or base of the
case neck.
Bulk Density - The ratio of the weight of a given volume of powder vs. the weight of the same volume of
water.
Burning Rate - A arbitrary index of the quickness that burning propellant changes into gas. Burning rate
is controlled by the chemical composition, the size and shape of the propellant grains, coatings, and the
pressure at which the burning takes place. IMR 5010 powder is very slow burning and Bullseye is fast
burning.
For a chart of comparative burning rates for current commercial powders you can click here.
CUP - Copper Units of Pressure. In this pressure measuring technique a hole is drilled in the chamber and
a piston fitted that presses on a calibrated copper slug (or crusher). (Some set ups also drill the cartridge
case which changes the results compared to non-drilled cases.) The whole assembly is held in place with a
yoke. When the cartridge is fired the piston presses on the crusher and deforms it lengthwise slightly.
Measurement of the length change is used with a lookup table supplied with each lot of crushers to
determine the peak pressure. The total deformation is effected by both the peak pressure and by shape of
the pressure curve around the peak pressure. This method tends to give readings slightly lower than the
actual peak pressure. A typical reading might be stated as 47,500 CUP which is supposed to be close to
the actual average psi measurement. This method has been largely superseded by piezo-electric and strain
gauge units which replace the copper slug with a crystal or strain gauge which changes its electrical
properties in response to pressure or dimensional changes. Such measurements are stated in PSI. For low
pressures a lead crusher can be used and measurements are in LUP.
Internal Ballistics http://www.frfrogspad.com/intballi.htm
1 de 12 27-05-2014 02:47
Typical Dual Measurement (Copper & Piezo-Electric) Pressure Gun
Expansion Ratio - The ratio of the capacity of the powder chamber plus bore (in grains of water) to the
capacity of the powder chamber (in grains of water).
Loading Density - The ratio of the weight of the powder charge to the capacity of the powder chamber
(case). It is usually expressed as the ratio of the charge weight to the capacity the powder chamber in
grains of water. (See below.) Generally, the more fully the powder charge fills the case the more consistent
and accurate the load will be. On the other hand if the loading density is too low, (too much free space in
the case) it can cause erratic ignition, change in the pressure curve (moving the peak towards the muzzle),
or even overly rapid burning ("detonation") of the powder charge. (One reason manuals list minimum or
starting loads.)
PSI - Pounds per square inch. It is sometimes seen designated as PSIA. This designation is now used to
signify a measurement of chamber pressure taken with a piezo-electric device or a strain gage. Piezo-
electric units operate in a similar fashion to the copper crusher units but use a reusable crystal "crusher"
that changes its electrical properties in response to pressure. When connected to suitable recording
equipment the entire pressure pulse history can be recorded or displayed. The peak pressure recorded by a
piezo-electric peak device usually reads higher than the figure determined by the copper crusher method
and depending on the cartridge and the pressures involved the differences can range between 3,000 and
15,000 units..
There are also electronic strain gauge units. These work by measuring the expansion of the chamber area
on firing by means of device that changes its electrical properties as it changes size. These devices are
very sensitive and if one knows the thickness of the walls of the cartridge case and the thickness of the
chamber wall, very accurate and detailed information on the pressure curve can be generated.
Internal Ballistics http://www.frfrogspad.com/intballi.htm
2 de 12 27-05-2014 02:47
Strain gauge on a dime
(Measuring the strain on the economy???)
Strain gauge mounted on rifle
(The white block is the connector
Piezo (PSI) and strain gauge (PSI) are not directly relatable to copper crusher (CUP) due to the
differences in the sensitivity of the copper crusher versus the other methods used to measure the
pressure. However, new statistical data analysis suggests that for most cartridges ANSI/SAAMI Maximum
Average Piezo (PSI) and Maximum Average copper crusher (CUP) taken in a "standard" barrel can be
approximated by the following formula which has an R
2
value (a statistical measurement of certainty) of
.927.
(1.51586 * CUP) - 17902.0 = PSI
While the relationship is generally within 3Kpsi (it assumes that the CUP was determined using ANSI/
SAAMI standards) one should not rely on this conversion for absolute maximum loads.
Interestingly the correlation between the European CIP CUP measurements and Piezo measurements has
an even better correlation with an R
2
of .997. The formula for the CIP conversion is
(1.20911 * CIPCUP) - 2806.88
The same warning about using this conversion for maximum load work applies to this formula.
Comparison of Pressure Specifications Between Copper Crusher and Piezo
SAAMI Specifications for .308 Win.
Max Average Pressure
Max Probable
Lot Mean
Max Probable
Sample Mean
Copper Units of Pressure
(CUP)
52,000 53,300 55,300
PSI (Piezo/Strain gauge) 62,000 63,600 66,000
Powder Chamber Capacity - As with most interior ballistics capacity measurements it is usually
expressed in grains of water. It is determined by measuring the weight of water that a fired case from the
test firearm can contain with a bullet seated to its normal depth. Note that this varies with different bullets
or seating depth as well as the dimensions of the chamber, and the brand of case.
Sectional Density - The is the ratio of the bullets weight (in pounds) to its diameter
Charge Weight to Bullet Weight ratio - This is the ratio of the weight of the powder charge to the
weight of the projectile.
What Affects What
Among the things that affect the internal performance (pressure and velocity) of a given cartridge & bullet
are:
Internal Ballistics http://www.frfrogspad.com/intballi.htm
3 de 12 27-05-2014 02:47
Capacity of the powder chamber (a function of chamber size and shape, case construction, and
bullet seating depth)
Relative burning rate and burning characteristics of the propellant powder used
Amount of propellant used and how much it fills the powder chamber (load density)
Diameter, weight, and the bearing area of the projectile
Length and interior dimensions of the barrel
Uniformity and speed of ignition of the propellant powder (Primer and loading density related)
Temperature of the propellant prior to ignition
Barrel freebore
Neck tension
Some Powder Basics
There are basically four types of gunpowder. Black powder, semi-smokeless, pseudo black powder
("Pyrodex"), and smokeless.
Black Powder
In the west it is generally attributed to Roger Bacon or Berthold Schwartz circa the 1200s, but they
basically popularized what had been known for a long time and did not invent it. It was undoubtedly
known to the early Chinese and Hindu people of India. Some early writings, circa 1300 BC, from these
cultures speak of such a substance though it was used as an incendiary or a demolition device and not in
"firearms." It is also clear that such a substance was known to the ancient Greeks. The earliest known
use of it as propellant in firearms was by the Arabs circa 1150 in their war with the Iberians. While the
exact proportions have varied over the years, but blackpowder is basically a finely ground mixture of
about 15% charcoal, 10% sulfur, and 75% potassium nitrate.
Blackpowder burns so rapidly that it actually explodes even with minimal confinement and unlike modern
smokeless powders it is classed as an "explosive". Other than for historical recreational shooting and the
manufacture of some types of blank ammunition, black powder is not in general use any more, and with
the recent "anti-terror" controls it is getting more difficult to obtain.
Brown Powder
This almost unknown powder was made using under-burnt charcoal and gave performance not very far
below later smokeless powders. Coming at the end of the black powder age it was superceded after little
more than a decade.
Semi-smokeless
In the late 1800s and early 1900s there was a type of powder known as Semi-smokeless. This was a
mixture of black powder and gun cotton (nitrocellulose) . Unfortunately the use of raw nitrocellulose
made its manufacture very hazardous and with the advent of modern smokeless powders it was
discontinued in the late 1940s.
Pseudo Blackpowder (Pyrodex and similar products)
Pseudo black powders such as Pyrodex, sold by Hodgdon, are a modern substitute for black powder and
remedy the explosive and fouling problems of black powder. Due to its chemical make-up, pseudo black
powder is classified as a flammable solid not as an explosive. Pyrodex can be substituted volume-
for-volume for blackpowder.
Smokeless Powder
The majority of todays small arms smokeless powders are made of either a nitrocellulose base, referred to
as single base powders, and typified by the IMR powders, or of a nitrocellulose and nitroglycerine mix
(usually from 3 to 39 percent), called double base powders, which include powders like Bullseye, 2400,
and Hi-Vel #2. An early form of smokeless powder was Cordite, which was a double based propellant
made of 65% nitroglycerine, by weight, 30% guncotton and 5% petroleum jelly, and loaded as
spaghetti-like strings of powder. There are also some special double base ball powders available in
Internal Ballistics http://www.frfrogspad.com/intballi.htm
4 de 12 27-05-2014 02:47
non-canister powders. Double base powders have a higher energy potential than single base powders.
Some modern powders referred to as "triple base" now incorporate an additional ingredient like
nitroguanidine, but these, like the double based ball powders are not in wide distribution except military
powders and some commercial grade non-canister powders. They can yield a substantial increase in
velocities while maintaining normal peak pressures as they give a longer, flatter pressure curve. In
addition some manufactures are using "blended powders" for some of their high performance
ammunition.
The grains of modern smokeless propellant powders are made in various sizes and shapes to give the best
results in the firearm they are designed to be used in. Powder for the 16" naval cannon has grains almost
an inch in diameter and 2 inches long while typical modern rifle powder has grains only 2/32 or 3/32 of an
inch long and maybe a 1/32 of an inch wide. The smaller the grain the faster it burns. Modern powders are
available in tubular grains, spherical grains, and flakes.
Most tubular grained powders have a hole through the center of the grain to allow burning to take place
from both the inside and outside surfaces. Without the hole, as the grain burned its surface area would
decrease and the amount of gas would decrease as the grain burned. Powders of this type, called
digressive powders, give peak pressures when the bullet is close to the breech and a low muzzle pressure.
By putting a hole down the center of the grain the burning area stays more constant and the maximum
pressure point is moved to a point where the bullet has moved further down the bore. These types of
powders are called neutral burning.
Another way of controlling the burning rate is with the use of a coating as used with ball powders, which
are made with spherically shaped grains. The coating on the powder grain tends to hold back the rate of
burning until the coating has burned through. These powders, called progressive burning give a peak
pressure at a point in bullet travel even further along. Coating technology is important in small arms
powders since without it the grains would sometimes have to be larger than practical.
Much has been made about ball powders being cooler burning than extruded powders, but the fact of the
matter is that there really isnt much difference. Flame temperature is very close to the same for all
smokeless powders and runs about 3300 degrees F. Ball type powders tend to be from 3200 to 3300
degrees F and extruded powders tend to run 3300 to 3400 degrees F but there is wide variation.
As a technical point of interest, conventional small arms propellant powders have an energy potential of
about 178 ft lb per grain of weight. However, in practice this figure is not even closely approached
because of various energy losses--such as the energy used in forcing the bullet into the rifling, overcoming
bore friction, heating the barrel, and giving the powder gases their high velocity, etc.-- that are inherent
and unavoidable. According to The World s Great Rifles, by Roger Ford (1998, Brown Packaging Books,
Ltd., London) it is estimated that just one-fifth of one percent of the energy produced when a cartridge is
fired goes to rotating the bullet, while friction in the barrel accounts for another three percent, 20 to 30
percent goes to propelling the bullet, 30 percent goes in heat to the barrel, and 40 percent goes in muzzle
blast.
Contrary to media myths, smokeless powder is not an explosive but rather a highly flammable solid. (Note
that we are talking about smokeless powders here.) As an example, one of the large powder grains used in
the 16" naval cannon can actually be lit while held in the hand and then blown out. Even individual grains
of modern small arms powders burn very slowly. But, when several grains or a pile of them are ignited
together the heat generated by each burning grain makes the adjacent grains burn even faster. A very
small pile of smokeless powder burned in the open may seem harmless but the resulting rapid ignition can
cause such a rapid build up of heat that a person may not be able to get away fast enough to avoid injury.
Inside of a cartridge case the same process happens but on a much shorter time scale.
Bang!
(What happens when the trigger is pulled.)
Internal Ballistics http://www.frfrogspad.com/intballi.htm
5 de 12 27-05-2014 02:47
When you pull the trigger and the primer fires, the intense flame created by the priming compound fills the
interior of the cartridge case and ignites the powder charge. The more nearly the powder charge fills the
case the less the powder gases generated by the burning powder can expand without doing work and the
more the heat generated accelerates the burning process as described above. (Thus a full or nearly full
case of powder is more efficient than a partially filled case.) The increasing pressures generated by the
burning powder pushes the bullet down the barrel. If the bullet is heavy, tightly held into the neck of the
cartridge, or if it is a tight fit in the rifling then the confinement of the powder is accentuated and the
burning is proceeds more quickly than if these conditions were not present--in other words you get higher
pressures more quickly.
The graph below is a representative pressure curve of a typical cartridge (in this case from the M193
5.56mm cartridge using 846 ball powder). Notice how the peak pressure rises quickly and then tapers off.
The location of the peak pressure and the shape of the pressure curve is determined by the burning
characteristics of the powder used and the loading density. Slower burning powders tend to have a flatter
curve while faster powders a steeper curve.
The gas port pressure curve on this chart shows a critical part of internal ballistics for cartridges used in
gas operated firearms. Gas operated weapons are generally tailored to a narrow range of powder burning
rates and characteristics. If the port pressure is too low the weapon will fail to function and if to high the
weapon may function too forcefully or rapidly causing extraction or cycling problems. A poorly
researched change of powder from an IMR type to a ball powder and the subsequent change of port
pressure and fouling was what caused all those nightmare stories about the M16 during the early days of
the Vietnam war.
Another very good graphical representation of what happens is shown on page 322 of "Hatchers
Notebook", (by Julian S. Hatcher, 3rd edition, June 1962, Stackpole Books, ISBN: 0811707954) but the
graph is a little data dense for good reproduction here. It is similar to what is shown above but it is based
upon the .30-06 cartridge, and along with the pressure curve it shows bullet velocity and time of bullet
travel.
As can be seen from the above graph, the longer the barrel the more time the powder has to work on
moving the bullet, so thus you get higher velocities with a longer barrel--all else being equal. However,
while not often reached with high powered rifles there is a point at which additional barrel length does not
Internal Ballistics http://www.frfrogspad.com/intballi.htm
6 de 12 27-05-2014 02:47
increase velocity, but rather causes a decrease.
As the bullet moves down the bore and the gas pressure behind it decreases there will come a time--with a
sufficiently long barrel-- that the bore friction and the air pressure in front of the bullet will equal the
pressure behind it. At that point velocity will start to decrease. With the .22 rimfire that point is reached in
about 14" - 16" of barrel. Beyond that length no velocity increase occurs, and in fact the bullet can slow
down, but the extra length may be useful for other things such as increased sight radius or legal
requirements.
If we have to keep barrel length reasonable, the way to get more velocity is to either change the burning
characteristics of the powder so it gives higher pressures over a longer time (as is done with the powders
in the new "enhanced performance" ammunition now available from Hornady and Federal), or to simply
burn more powder by using a bigger cartridge case.
By using a cartridge case with greater capacity we provide for more chamber volume with the same bore
volume, thus the expansion ratio (see definitions above) becomes less. As a result, the powder gases have
been through less expansion by the time they reach the muzzle and muzzle pressure is higher. As the
muzzle pressure is higher, the average pressure along the bore is higher and the bullet has a higher
velocity. There is a trade off for this. Because the muzzle pressure is higher, more energy is carried off into
the air unused (as flash and muzzle blast) and thus the efficiency of the load (the getting of energy out of
the powder charge) is less.
Here is a sample output from PressureTrace for a 6 PPCcartridge. The only difference between all these
traces is the first 3 were seated right on the lands. The last 4 were 30 thousands of an inch off the lands.
Note the substantially reduced pressure and overall reduction in energy. As the bullet broke its neck
tension and jumped to the lands it provides more expansion room for the gases reducing both the energy
and velocity.
The Hacksaw Effect
(Sometimes referred to as "get shorty.")
The often asked question of "How much velocity will I lose if I shorten my barrel "x" inches?" is tied quite
closely to the expansion ratio, although the type of powder also plays a part. Thus there is no clear cut
general answer as to just how much velocity is lost per inch of barrel shortening. Rifles with high
expansion ratios tend to lose less velocity as the barrel is shortened than do rifles with low expansion
ration. Thus a .300 Win Mag will lose more velocity per inch of barrel than say a .30-06 and it is not
uncommon for a smaller cartridge in a long barrel to out perform a big bottle cartridge in a short barrel as
some folks found out to their dismay when they chronographed their 22" razzle-dazzle magnums next to
Internal Ballistics http://www.frfrogspad.com/intballi.htm
7 de 12 27-05-2014 02:47
their buddies convention calibers with 24" barrels.
Because of the fact that "high velocity" cartridges generally have low expansion ratios (big cases in
relation to bore diameter) one can make some generalizations. The chart below will give you some idea of
what can be expected if you cut your barrel shorter within the range of 20" to 26". Remember, your
mileage may vary from this chart. Note that this chart does not hold true if we are comparing different
barrels of different lengths. In that case it is quite possible, due to certain barrel design parameters, for a
short barrel to give higher velocity than a longer one with the same ammunition.
Velocity Range
Vel change
per inch
0-2000 5-10
2000-2500 10-20
2500-3000 20-30
3000-3500 30-40
Mathematical Calculation of Internal Ballistics for the End User
There are some "mathematical" methods of computing a fairly close approximation of the actual internal
performance (i.e.: chamber pressure and muzzle velocity) of a given combination of cartridge, firearm,
bullet, and powder but their details are beyond the scope of this page. The "Powley Computer," a slide
rule type device was at one time available and gives rather good results when used with the "IMR" type of
powders and cases of similar capacity to the .308 and .30-06. It is based on some mathematically derived
"constants" developed at Frankord Arsenal which provide a close approximation to the results derived by
some rather complex mathematical gyrations. Several computer-based adaptations of these calculations
are available from different sources (such as the rather expensive QuickLoad program) and all suffer from
the limitations of being based upon the Frankfort Arsenal model of the .308/.30-06. As far as I know the
Powley Computer is no longer available although Powleys code has been privately adapted to computer
use by various people. As mentioned previously these computations are based upon case capacities and
pressures in the .308 Win & .30-06 range. For cartridges of significantly larger or smaller capacities, or
lower pressures, the result will be not be accurate and can frequently be dangerous if you dont understand
what is what.. There was a website that allowed you to make your own slide rule computer, but it is no
longer active. However, there is an online adaptation of the Powley Computer available at http://kwk.us
/powley.html
Mechanical /Electrical Calculation of Internal Ballistics for the End User
Consumer Crusher Systems
Crusher based pressure systems are generally beyond the means of the average shooter. At one time there
was available a "do-it-yourself" pressure measuring device using a "crusher" type tool. Rather than
utilizing a drilled chamber this unit was mounted on a firearm in place of the telescopic sight and when the
firearm was fired the recoil impulse compressed the crusher which could be measured and compared to a
calibrated table. Unfortunately, the unit was tricky to set up, required very precise measurements of the
firearms weight, and if memory serves me right worked best when the firearm was unrestrained in recoil
(as in hanging from support wires). It was also only really suitable for rifles.
Strain Gauge Systems
There are moderately priced electronic strain gauge unit available that do a better job and allow one to see
the pressure curve on an oscilloscope or a computer screen and which dont require a special free swinging
support. The new PressureTrace II system and the the no longer available $800 Oehler Model 43
"Ballistic System" with its $170 add-on a strain gauge pressure sensor are examples of this technology.
Strain gauge units with real-time microprocessor compensation such as PresureTrace II have been shown
to actually be more accurate than either piezo or crusher measurements. By utilizing certain easily
measurable parameters of the chamber wall thickness and cartridge case wall thickness in the firmware
Internal Ballistics http://www.frfrogspad.com/intballi.htm
8 de 12 27-05-2014 02:47
and software, the measurements from strain gauge units give results that are accurately given in PSI. (If
no compensation is utilized with a strain gauges, the measurements are in arbitrary units, such as
"coconuts" as my friend says, which still can be used for comparison readings.
Strain gages have been used in industrial instrumentation for several decades and is fully developed,
proven technology. Denton Bramwell, (physicist and statistician with a great deal of test instrumentation
experience) recently compared the results of various pressure measurement methods . He used a standard
measure of how likely a system will give correct answers called "Sigma E" for comparison. (Smaller Sigma
E values are best.)
System Sigma E
Copper Crusher
Fabrique Scientific Peak Strain Meter
Commercial piezoelectric
Microprocessor compensated strain gauge
1827 psi
1419 psi
1366 psi
667 psi
The PressureTrace II unit gives you the actual readings in your firearm, while the Oehler unit converted its
measurements to what would probably be obtained by the load in a SAAMI specification test barrel. For
the details on the PressureTrace II go to http://www.shootingsoftware.com/pressure.htm.
I have worked with RSI on the development and production of the PressureTrace II unit and I personally
use it. It is VERY neat but not inexpensive, running around $500. If you do order one Id appreciate it if
you would let RSI know that I sent you by telling Jim.
NOTE: While you can reliably compare the pressure generated by your handloads with the pressures
generated by factory ammunition fired in your gun, or compare the pressures from different handloads in
the same gun, strain gauges or recoil based pressure devices do not generate " SAAMI specification"
pressure measurements (either PSI or CUP) even thought the results are probably more accurate,
because SAAMI specifications currently requires piezo or crusher pressure technology and certain
convoluted statistical analysis of the data, as well as requiring that the barrel and chamber be minimum
specification to provide "worst case" data. Does it really matter? No.
Case Head Expansion
Some people think it is possible to estimate pressures from cartridge case head expansion. This has been
shown to be incorrect and there is little if any correlation between case head expansion and pressures.
Rather than reinvent the wheel here visit http://www.shootingsoftware.com
/ftp/dbramwell%20july%2019%2004.pdf for an in depth discussion.
Continuing on...
We know that as pressure goes up, so does velocity. Pressure goes down, so does velocity. If you are
worried about pressures, and dont have access to pressure equipment, develop your loads using a soft
primer like Winchesters and a chronograph and find the top node or stop when you get flattening or
cratering. Then switch to a harder primer and adjust your load to give the node velocity.
While these pressure measuring devices can be very informative for someone with a interest in interior
ballistics and the effect that things like different powders and seating depths, most folks who buy these
sort of devices dont understand barrel harmonics and velocity nodes. (See the discussion of "load
development.") They hope to be able to load all the way up and wring the last foot-second of velocity out
of their guns. They forget that the top velocity/accuracy node reachable without signs of excessive
pressure (primer flattening/cratering) is the top practical limit for a firearm.
So, what good is being able to "read" pressure? Using PressureTrace II can let you see the effect of
burning rates on pressure curves and and the effect of the change of the shape of the pressure curve all of
which have an effect on velocity. For many folks it is simply fun to see what is going on. With a highly
sensitive unit with a high sample rate like PressureTrace II you can also see the effect of many other
things like neck tension, seating depth and powder / bullet / cartridge match. In addition if you are trying
Internal Ballistics http://www.frfrogspad.com/intballi.htm
9 de 12 27-05-2014 02:47
to work up a load for a cartridge with little or no published data, a pressure unit can help to keep you safe
if you start with data for a cartridge with a similar case capacity and then slowly work up from the lowest
pressure loads. If you are working with modified non-standard chamber designs or rifling you can see
what is happening and work up safe loads rather than guessing. The loading data for the DMR chamber
design for the 6.8 x 43 mm (6.8 SPC) was developed using a PressureTrace II unit.
Rules of the Road
(Or, things to keep in mind when developing loads)
Rule 1 - Dont do anything stupid.
Rule 2 - For a given load a 3 percent rise in velocity requires a 6 percent rise in chamber pressure.
Rule 3 - For a 3 percent change in case capacity chamber pressure changes by 6 percent. Remember that
case capacity varies drastically between brands of cases and that bullet seating depth also changes case
capacity.
Rule 4 - Changing ANY component can drastically effect chamber pressure.
Rule 5 - You DO NOT need to wring the last possible foot-second of velocity out of your ammunition--it
wont do anything for you. An accurate/moderate velocity load is better than an inaccurate/fast load. (See
the external ballistics and load development pages)
Rule 6 - Temperature affects chamber pressure. While the effect differs with each powder, over the range
of about 0 F to 125 F most modern commercial powders are fairly stable showing pressure variation of
up to 3000 psi from loads developed at 70 F. Out side of this range the effect is still there but not as
linear.) While most current ball powders handle temperatures changes well some types have exhibited a
very non-linear response especially at temperature extremes outside of the above range and can result in
catastrophic changes in pressures at temperatures much higher than the original temperature. Loads with
any powders should be carefully worked up if their use in extreme temperatures is expected especially if
at near maximum (Click here for a chart of temperature effects.)
Rule 7 - Dont do anything stupid.
Remember, Watcha-U-Back
(...or, once again, don't do anything stupid)
Unless you are well versed in internal ballistics leave the development of loading data with new powders
to the experts with the proper tools, and dont play around with unknown powders. More than one firearm
has been destroyed when the wrong powder was used without proper knowledge. As an example, in the
50s and 60s there were a lot of blow ups caused by people trying to use the powder from GI .30-06 blanks
in pistols and rifles. What these poor souls didnt realize was that the "EC" powder in those blanks burned
so fast that it was also used as a grenade filler. These folks turned their firearms into "grenades" with quite
small charges of this powder. By the same token many powders of vastly different burning rates look
similar. If its not in the original can, dont use it!
Leave new load development to the pros and stick with the data in reliable loading manuals.
Bullet Stability
While some may think that bullet stability is an external ballistics issue, it really starts in the bore.
Bullets are stabilized in flight by the gyroscopic effect of their spinning and their spin rate is determined by
Internal Ballistics http://www.frfrogspad.com/intballi.htm
10 de 12 27-05-2014 02:47
their muzzle velocity and the rate of twist in the barrel. A badly unstable bullet will actually wobble or
tumble in flight resulting in extremely poor accuracy.
The needed rate of twist is effected by the diameter of the bullet, the bullets weight, and the bullets
overall length. Longer bullets need a faster twist to stabilize. As an example, a 1:12 twist in .30 caliber will
adequately stabilized most commercial bullets of up to about 173 grains (depending on the overall length).
To use a heavier (longer) bullet or to obtain optimum stability and accuracy with long pointed or boat
tailed bullets of that weight requires a 1:10 twist. For best accuracy the slowest twist that will stabilize the
bullet should be used. Bullet stability is describe by a number called the Gyroscopic Stability Factor. A
stability factor of from 1.25 to 2 is considered "stable." Below that range the bullet is most likely not
stable enough for accurate flight. Above that range the bullet may be spinning so fast that it may
physically rupture from the forces involved, or minute imbalances that normally would not come to light
begin to cause problems.
There is an old formula called the Greenhill Formula that, while it was designed for estimating twists for
boat tailed lead core bullets of moderate velocity, does a pretty good job of estimating twist required for
flat based bullets under "normal" conditions.
T = Twist in inches
K = Greenhills constant = 150 (This has to do with the specific gravity of a jacketed lead
bullet)
D = Bullet diameter in inches
L = Bullet length in inches
T = (K * D
2
) / L
Using a 1.35 inch long .308 bullet (173 gr) and crunching the numbers we get about 10.5 (One turn in
10.5", which is pretty close to the 1:10 twist normally used in .30-06 rifles. The twist for the .308 is
nominally 1:12 because it was based on the shorter bullet of the150 gr military ammunition from which
the .308 commercial round was developed. Most match rifles in .308 have a 1:10 twist to stabilize the 180
and 190 boat tailed match bullets better. The results from the Greenhill formula are on the conservative
side--indicating a faster twist than probably needed. That doesnt cause any problems because a little too
much stabilization is better than too little.
However, the one big catch with the Greenhill formula is that it does not account for the effects of
temperature or muzzle velocity. As temperature or velocity decreases a faster twist is needed to maintain
the same level of stability. Colder and thus denser air has a more destabilizing affect than warmer air. A
lower muzzle velocity results in a slower rotational speed of the bullet and thus less stability.
As an example of the effect of temperature, the original M16 rifle for the M193 55 gr ball came out with a
1:14 twist which was barely stable at 68 degrees and which was totally unstable below about 40 degrees.
They changed to a 1:12 twist to get stability (barely) at colder temperatures. The M855 62 gr round is
unstable below about 65 degrees with the 1:12 twist and requires a 1:9 twist to be stable. They went to a
1:7 twist because the M856 tracer round has a very long bullet, but the ball round does just fine in 1:9.
Modern bullet stability calculations are based upon the work of the late Robert L. McCoy who was a
ballistician with the Ballistic Research Laboratory at Aberdeen Proving Ground. His work, now used in
advanced ballistics programs, accurately takes into account all of the factors involved in bullet stability
and accurately describe the bullets behavior at a given muzzle velocity and twist rate and generates a
stability factor for a range of muzzle velocities.
For velocity issues long bullets are more susceptible than short ones. For example the above 173 gr .308
bullet in a 1:12 twist barrel is stable from at muzzle velocities of 4000 f/s down to about 500 f/s . Below
that muzzle velocity it becomes unstable. If we turn the design into a VLD bullet with a length of 1.45" (a
VLD design has a longer more pointed ogive so the bullet itself gets longer) the bullet is stable for muzzle
velocities from 4000 f/s to 3,000 f/s in a 1:12 twist. Going to a 1:11 twist the bullet is stable at muzzle
Internal Ballistics http://www.frfrogspad.com/intballi.htm
11 de 12 27-05-2014 02:47
velocities of 4,000 f/s down to about 1150 f/s, and going to a 1:10 twist make the bullet stable at muzzle
velocities of 4000 f/s down to about 500 f/s
Another catch with the Greenhill formula is that Greenhill assumes that the bullets specific gravity is 10.9
(a lead cored jacketed bullet). For other bullet construction such as a steel core you need to apply a fudge
factor by determining the bullets specific gravity. The formula would be:
Twist = [Square Root (10.9 / specific gravity of the new bullet)] * twist derived for a lead core bullet
You can determine the specific gravity of a bullet thusly:
1) Suspend the bullet at its balance point from the pan of a scale.
2) Weight the bullet.
3) Place a container of water under the scale so the bullet hangs fully in the water and weigh the bullet.
4) Subtract the weight obtained in step 3 from the weight obtained in step 2
5) Divide the weight obtained in step 2 by the difference obtained in step 4.
As an interesting exercise you can also determine the spin needed in mediums other than air under
"standard conditions" by multiplying the spin for air by the square root of the number obtained by dividing
the density of the medium in question by the density of air. As an example water is about 900 times as
dense as air: 900 / 1 = 900 and the square root of 900 is 30. Thus you need a twist 30 times as fast to
stabilize a bullet in water.
Sharp eyed reader may note that the McCoy stability computations are based upon muzzle velocity. This
is the case because the rotational speed decays much more slowly than velocity decay. Most of the
research in this area was done by the Ballistics Research Lab at Aberdeen Proving Ground and Picatinny
Arsenal on artillery projectiles which have narrow driving bands that are engaged by the rifling rather than
full body length rifling engraving on the bullet as with small arms projectiles. Thus there are some
approximations made on spin decay for small arms projectiles. For the M80 147 gr 7.62 NATO bullet at
2750 f/s which has been studied and investigated thoroughly, the approximate spin decay at range is as
follows and the decay rate probably holds true for other small arms cartridges.
Range Muzzle 100 200 300 400 500 1000
Percent of
spin
remaining
100 98 96 93 91 89 75
Bullet RPM 198,000 194,000 190,000 184,000 180,000 176,000 148,500
To email me click here
| Ballistics Main Page | External Ballistics Page | Zeroing Page | Terminal Ballistics Page |
| Rifle Power Page | Misc. Questions |
| Back to Fr. Frogs Home Page |
Disclaimer
As far as I know all the information presented above is correct and I have attempted to insure that it is. However, I am not responsible for any errors,
omissions, or damages resulting from the use or misuse of this information, nor for you doing something stupid with it. (Don't you hate these disclaimers? So
do I, but there are people out there who refuse to be responsible for their own actions and who will sue anybody to make a buck.)
Updated 2014-03-01
Internal Ballistics http://www.frfrogspad.com/intballi.htm
12 de 12 27-05-2014 02:47