Copyrights..................................................................................................................................................

2
1. Overview...............................................................................................................................................2
1.1.1 GENIUS G840 Characteristics.................................................................................................2
1.2 System Requirements..........................................................................................................................4
1.3 Programmer Package...........................................................................................................................4
2. Install the Software................................................................................................................................4
2.1 Setup G540(or G840) Software ..........................................................................................................5
2.2 Install USB Driver...............................................................................................................................7
3. Quick Guide.........................................................................................................................................10
3.1 Description of User Interface *(UI) .................................................................................................10
3.1.1 Main menu and Toolbar..........................................................................................................11
3.1.2 Information window...............................................................................................................11
3.1.3 Data buffer..............................................................................................................................12
3.2 Operation Intro...................................................................................................................................13
3.2 1On_Line (means connect the hardwar to PC):...................................................................13
3.2.2 The off-line operation (Only G840)......................................................................................14
4. Expatiation...........................................................................................................................................15
4.1 Base Operation...................................................................................................................................15
4.1.1 Select Device.........................................................................................................................15
4.1.2 Load File.................................................................................................................................16
4.1.3 Set Encryption .......................................................................................................................18
4.1.4 Insert device............................................................................................................................18
4.1.5 Program...................................................................................................................................19
4.1.6 Erase.......................................................................................................................................20
4.1.7 Blabk.......................................................................................................................................21
4.1.8 Verify......................................................................................................................................21
4.1.9 Encrypt....................................................................................................................................21
4.3 The Brief Introduction of support device..........................................................................................21
4.4 About power source adapter..............................................................................................................22
4.5 IC Test................................................................................................................................................23
4.5.1 Test known Device.................................................................................................................23
4.5.2 Tests the unknown Device......................................................................................................25

Copyrights
Software Copyright
20080101
Users Manual Copyright
20080101

STAGER
STAGER

The distribution and sales of the product are intented for use by t
he original purchaser under the terms of the License Agreement. This
document
may not, in whole or part, be copied, Photocapied, reproduced, transl
ated or reduced to any electrowic medium of machine-readable from
without prior
consent in writing from STAGER.

1. Overview

Genius GXXX serie productions lineup:

GENIS G540 universal programmer:USB communication,40 pins locking
socket, Updatable by software.Powerde by USB .Contour: 143mm112 mm25
mm.

GENIUS G840 universal programmer:USB communication,40 pins lockin

g socket,Full Pin_Drived, Off_line Operation,Updatable by software.Po
werde by 5V1000MA powersupply Contour: 143mm112 mm25 mm

1.1.1 GENIUS G840 Characteristics

GENIUS G840 is a newst type of the GENIUS programmer family. I
t has the features as following except the usual performances of othe
rs.
1. 40 pins Locking Socket.Full Pins Drived .
2. Updateable by software. The users enjoy the lifelong updating su
pport.It need only to download the newst software from our net site
to complete the update. (Please login to: http://www.sta51.com )
3. On-line operation and off-line operation fuctions. It is both suita
ble to the development, the testing, the teaching, and suitable to the

batch programming.
4. Touch key. You may not need to click on the mouse, which cause
s the operation to be more convenient. The touch key is durable and
be never damaged.
5. Pin Contacting detection. In the cases of poor conect between t
he IC and the sockt or wrog puting, the informations will be detected
and the operation will be broken.
6. Triply indicats the operating result: displaied in the window, in th
e LED lamp and choseable buzzing.
7.Powver supply: 5V1000mA.Low Power consumption(<200mA) so as
to avouch Non Over heat.
8. Perfect defenses. That both refrain effectively from to damage
user device and protect itself.
9. The pocket-sized and compact outward, provides a good visual
effect and a convenient carries.
Also, GENIUS G540 is a newst type of the GENIUS programmer
family.
It has the features.
1. 40 pins Locking Socket.
2. Updateable by software. The users regale the lifelong updating su
pport.It need only to download the newst software from our net site
to complete the update. (Please login to: http://www.sta51.com )
3. Pin Contacting detection. In the cases of poor conect between t
he IC and the sockt or error place, the informations will be detected
and the operation will be broken.
4. LED indicator.
5.Powvered by BUS .Low Power consumption(<200mA) avouch Non
Over heat.
6. Perfect defenses. That both avoid effectively to damage user d
evice and protect itself.
7. The pocket-sized and compact outward, provides a good visual
effect and a convenient carries.

1.2 System Requirements

The minimum requirements are as follows:

A personal computer with one USB port , CD-ROM driver windows 98/NT/2000/X
P operating system, There are least 100M of spare space on the Hard disk

1.3 Programmer Package

Standard package contains the following:

Main body of programmer 1 pcs
USB connecting cable

1 pcs

AC/DC adapter (Only G840) 1 pcs

The installation software CD 1 pcs
Users Manul
Registration card

1 pcs
1 pcs

2. Install the Software

If it's your first time to use the USB-based programmer of Genius Gxxx, This chapter
will help you to install the software and to connect the hardware.
There are tow parts will be installed:G540(or G840) Software & USB Diver.
USB device is PnP device. The USB Driver must be installed before the device can
be used.At first.time installation, windowns will start with new hardware wizard to sca
n all available INF files and find out the appropriate USB Driver

2.1 Setup G540(or G840) Software

1. First of all, insert the CD into CD-ROM driver.

2.Double click the G540Setup(or G840Setup) in the foldr SetupFil
e to run it.The following window be showed:

Figu 1

Click the buttonNext,The window is changing as:

Figu 2
Now, you can chang the destination folder if you want to do.Th

en click the button Next.The widow is changing as following:

Figu 3
Click the Next again to go on

Figu 4
Please read the text carefullyclick button "Install"

Figu5
The files are copying.After this process,it will display followiong infor
mation:

Figu 6

Click button Finish to finish the setup.

The Shartcut Icon of G540 (or G840) was created on the desk
of the PC

2.2 Install USB Driver

The installation of the USB Driver contains tow steps:one is per-installing and anat
her is connecting USB device

Step 1:Pre-inteall the USB Driver. This step is in oder to copy automatically all file
s of the Driver to PC.
Double Click to run the StgICproUSB_Installer.exe at the folder USB_DRIVER o
f the DISK.The window as following:

Figu 7
You can chang the Installing location if it is necessarily.
Then click the botton Install.
It showing:

Figu 8
Click the button OK.Finish Step 1.
Step 2 Connect the USB device. This step connect the USB device to the pc and i
nstall the specific files to Widows system automatically.
Connect the Programmer main body to PCs USB interface.The LED lamp light.(if
it is G840, the power must be turn on).The PC is scaning the new USB device and is sho
wing the window.(note: her use chinese version window for example.)

Figu 9
Select the automatically then click the button Next.The window changes:

Figu10
Click the button Finish to finish the installation

3. Quick Guide

This chapter helps users understand the process of IC programing.

3.1 Description of User Interface *(UI)

The hardware must be connected with PC befor run the soft ware.
Double click the shartcut Icon of the G540 (or G840) on the PC desk to run it. The
UI appears user
(F21)

Main menu

Tool bar

Information window

Figu 11

3.1.1 Main menu and Toolbar

Same as general Windowns software, any operation of G540(or G840) can be executed
on the main menu or the toolbar.
The main menu of G540(or G840)includ File, Edit, Operation, View, Set,Help.The t
oolbar includs the functions often used, they are Load,Edit,Select,Progrmming,Eras, Bloc
k check,Verify, ....

3.1.2 Information window

The Information window is used to demonstrate the IC information , programming env

ironment and operating results

(F22)

Figu 12

3.1.3 Data buffer

f23

Figu 13

This window demonstrates the data of the PC data buffers. The demonstration formatio
n may be either Hexadecimal(HEX) or JED. The buffer data may be gotten from one of t
hree methods,that is Loading the file ,Reading the device or Editing the data buffer. The
Data Buffer window is close when start the G540. and it will automatically display after y
ou load file,read from device,or fill the data buffer.

3.2 Operation Intro

3.2 1On_Line (means connect the hardwar to PC):

Click the button SELE on the toolbar .Select Device lass,Manufactory,Device ac
cording to the target device.
2Load data:
If your datas are at the data file, click the button Load on the toolbar . Locate to you

r data file then open it .

Note: Must select the formation to match the formation of the file.
If your datas are in the sample device,please place the sample device into the lockin
g socket then click the button Read on the toolbar.This operation read the device data to t
he buffer.
3Set Encryption or Configuration value.
Click the button Config Encrypt SET. to set Encryption or Configuration parameter acc
ording to the device attribute.
Note: The seting values take effect after Encrypt operation
Some of device may has not the encrypting feature.
4Set Programming Operation Sequence
There is a default Programming Operation Sequence for each device selection . Genera
lly it is not necessarly to chang.If you want to chang it,you can click main menu SetSet
Programming Sequence .
5Place the target device on the locking socket
6Click the button.Prog on the toolbar, the Programming Operation Sequence be set at
step 4 are automaticaly orderly executing
7Replay 5, 6, to program anather device.

3.2.2 The off-line operation (Only G840)

The Off_Line Operation means that the Programmer run solely without cennected to P
C.The informations are needed download to the programmer hardware befor Off_Line op
eration.
After do the steps 1 to 4 in the section 3.2,click the button DL Off_Line in the toolbar t
o download the informations and to break the logic connection.
Aftertime,you can use it without connecting the programmerto PC.
Refer to section 4 for detaill.

4. Expatiation
After you read the Quick Guide, this chapter will tell you all the funcitions of the prog
rammer.

4.1 Base Operation

GENIUS G540s operations can be executedr by the main menu or the toolbar. The opra
tions may mostly be completed by one-click, but some time may need multi- steps.

4.1.1 Select Device

Click button SELE (toolbar), display the Select Device windown.( )

Figu 14

Please select the Device class ,Manufactory ,and Device type according to the attrib
ute of the target device.
We recommend that you use as far as possible the selection matching with the target
device.

4.1.2 Load File

The Load File load the data from the data file into data buffer of the G540(or G840).
Click button Load (toolbar), the Open file dialog box will be display.

Fogu 15
Locat to your data file location ,double-click the file name or click the button Open,
the window is closing, at the same time, the File loadding mode window will show.

Figu 16
Please select the File Formation.It is must matching to the formation of your data file.
It is often not necessarly to chang the Offset address,the Loading mode and the Fill
mode in blank area.
Click button OK,that will close dialog box.The Data Buffer widow display automati
caly.
For memory(include EPROM,EEPROM,FLASH,Serial_EEPROM) or MCU,the dat
a formations may be HEX or Bin. For the PLD the data formation is only JED.
The file that is HEX or JED formation be created by specific assembler.
You can chang the File offset address or Buffer offset address to load the data of the
file to different location of the data buffer.The dfault offset addresses are 0.
Fill mode in blank area can be With xxH,or non care it ,her xxH is any value.The def
ault value is 0FFH.
You can connect tow or more files if you use the Offset address and Fill mode in bla
nk area.For a example: connect file a.hex and b.hex. first, you can load the file a.hex with
Datauffer offset address 0 and Fill value 0FFH,then load the file b.hex with Data buffer o

ffset address xxxxH and Non care Fill mode.her the xxxxH is the end address of the file a.
hex.

4.1.3 Set Encryption .

After you selected a new type device that it need to encrypt or need to config,you m
ust set the encryption paramters.
Click the butoon Config Encrypt SET on the toolbar.It will show the following wind
ow.(This window is for PIC16F73.It may be diferent for different device)

Figu17
Set the parameters.then click button OK to close the window.
Note: The seting values must be written to the device by Encrypt operation

4.1.4 Insert device

When you selected a type of device to program,the inserting mathod of the device wa
s ascertained It is shown with diagram.Rafer to Figu 12
Put the target device into the locking socket and lock it.

Note: Dont insert the device before turn on the power, and dont take out the device a
fter turn off the power, so as to prevent the wrong operation from unstable period of ON/
OFF power.

4.1.5 Program
The programming operation is a combination of multi-opernations.These operations are
repetitive used .
The operation sequence of programming are created when start the G540 or select a ne
w type of device.You can rearrange the sequnce if it is necessarly
1. Rearrange Sequnce of Programming
Click Set Programing Operation Seunceat main menuand pop up a dialog box of
Programing Operation Seunce.The options will appear on the left column of the dialog
box, and selected items will appear on the right. The selected items will be orderly execut
ed by pressing the Prog utton.on the toolbar
Select an option on the left, and press the button ADDor double click the ite
m then this item will be added to right. If you need the same item, you can add more. C
ontrarily, select an item on the right column, press buttonDelete X, or double click the i
tem bar, and this item will be deleted.

Figu 18

2. Programing
Click the button Prog on the toolbar.The operation sequnce are oerderly executed
Replay 4.1.4 & 4.1.5 2 to program anather devices
The buttons Erase Blank Verify Encrypt on the toolbar can be execute
d step by step when it is necessarly

4.1.6 Erase
For EPROM type, it demands that we erase it by using ultra-violet eraser. For the type
of EEPROM, FLASH ect, we can accomplish it on this programmer. Click the Erase bo
ttom in the toolbar, complete the erase at once.

4.1.7 Blabk
Click the button Blank in the toolbar, the blank operation will excute

4.1.8 Verify
The operation is compare the content of the Programmed evice to the content of data
buffer so as to confirm the Program whether correct. The verify operation should be do
ne before encrypt! We just need to click the button Verify on the toolbar the result wi
ll be displayed in the information window.

4.1.9 Encrypt
The Encryption parameters must be set befor encrypting if the device selection is n
ewst Refoer to section 4.1.3
Click the button Encrypt in the toolbar .

4.3 The Brief Introduction of support device

Following is only the brief introduction of support device.Refer to file DeviceList_G54

0(DeviceList_G840) on the Disk for detail.
1. EPROMultra-violet erase memoryall big brands'EPROMin clyd
ing:271627C16273227C32276427C642712827C1282725627C256
27C51227C01027C040 etc.
2. EEPROM and Flashelectric erase memory281628C1628172
8C1728C6428C25628C01028F51228F01028F02029C25629C512
29C01029C02039SF25639SF51239SF01039SF02039SF040 and 4
9...

3. MPU(micro controller)
The 51 series micro controller mainly using
ATMELAT89C51/52/55WD/LV55AT89S51/52/53/AT89C1051/205
1/4051AT90S1200/2313/Attiny11/12/15
Winbond77E58/78E51/78E52/78E54/78E58/78E516/...
AMD87C51/87C521/87C541
LGGMS97C2051/97C54/97C58/97C2051/97C4051/
INTEL87C51~87C5887C5FA~FC87C51RA~RT...
SSTSST89C54/5889F54/58...
The other brands' 51 series micro controller
PIC series micro controller
Micvochip PIC12C508/509PIC16C50216C52/54/55/57/58PIC16C61/
62/620/621/622/623/624/625PIC16C63PIC16C64/65/67PIC16C73PIC
16C74/76/77PIC16C745/765PIC16F72/73/74/76/77PIC16F870/871/87
2/873/874/876/877/877A/84PCF745/746
MDT series MDT2005 etc.
PLDprogrammble gate arraymain include
ATMELAT16V8AT20V8AT22V10ATF16V8ATF20V8ATF22V10 e
tc.
LADICEGAL16V8GAL20V8GAL22V10 etc.

4.4 About power source adapter

Genius UA800 universal programmerUSB communication

1Under the on-line pattern may use the USB power supply, generally
do
not have to use the power source adapter to supply power. When US

B
power supply ability insufficiency may use the power source adapter t
o
supply.
2Under the off-line pattern uses the power source adapter power su
pply,
uses AC110 - 240V, DC6V1000mA (center, outer annulus negative)
Genius SU0640 universal programmerUSB communication
Uses the USB direct power supply, does not need the external po
wer
supply
Genius SP2006 universal programmerserial communication
The use power source adapter power supply, uses AC110 - 240V, DC5V1000mA (cente
r, outer annulus negative)

4.5 IC Test
The function of IC test mainly is aims at the RAM component, TTL (the 74LS series, th
e 54LS series), the CMOS4000 series general digital circuit says.
IC Test have two situations
1Known its modle, test it whether is in good condition or has broken;
2Unknown its modle, search and analyze which modle it is belonged.

4.5.1 Test known Device

The component put in the locking socket lock it , then click the tool bar "Select" key, Se
lec" RAM test" or "test TTL or CMOS" ,Show the dialog box:

Figu 19

Clicks on " Test known" button, that will spring the dialog box of choice component.

Figu 20

Please select the divice that is as the same as the target device clicks OK button to clo
se the window.Put the target device into the socket Click the button Test on the tool bar, t
he system starts to test the device, and the result will demonstrate in the information

4.5.2 Tests the unknown Device

See the Figu 18 and select the Find the Unknown type,the window changes as followin
g:

Figu 21
Please select the IC Pin Number same as the number of the target device. Put the target
device into socket then click the Test button on tool bar. result will demonstrate as followi
ng:

Appendices
License Agreement
The copyright of the program and user's guider remain the property of STZGER.

you may:
Copy the program for back-up purposes ONLY in support of its use on a single comput
er.
Transfer the program and license to another party if the other party agrees to accept th
e terms and conditions of this agreement.

you may not:

Use this produet in a computer system or network, which allows the program to be oper
ated by more than one user at a time.
Modify, copy, or transfer the user's Guide, other documentation or any copy.
Reverse engineering, de-compiling, or disassemkble any program module or security de
vice.

Customer Support
Congratulate on you have Genius series program machine. you had been a friend of sta
ger Electric CD.LTD for all time.
Keep good your purchase credential, you will get favorable affer service and preferentia
l treatment:
If meet software update, you will have fruition right for free.
Supply corresponding technique service.
Guarantee to keep it in good repair for half a yesr for free, and supply service for life.
you can take 80% of market value to buy any other production of Genius series.
Software updates are available free from the web site.
Http://www.stg51.com
The telephone of technique service is +86075582528167

[email protected]
fax: 0755-82526062