10gigabit XFP Optical Receiver

RTXM226-406
Wuhan Telecommunication Devices Co., Ltd.

http://www.wtd.com.cn

1

10Gigabit XFP Optical Receiver
RTXM226- 406
Features
Compliant with XFP MSA
Data Rate from 9.953 Gbps to 10.7
Gbps
APD ROSA
I ndustry- standard,
protocol- independent XFI
interface
Power dissipation<1W
LC duplex receptacle package
Low power dissipation
Hot Pluggable
Built in digital diagnostic
Functions
Operating case temperature range:
0
o
C~70
o
RoHs compliant
C
Application
SONET OC- 192 SR- 1&SDH STM
I - 64.1
10GBASE- LR/ LW 10Gigabit
Ethernet
Standards
XFP MSA

RTXM226-406

2
Absolute Maximum Ratings
Parameter Symbol Unit Min Max
Storage Temperature T
s

o
C -40 85
Supply Voltage 1 VCC3 V -0.5 4.0
Supply Voltage 2 VCC5 V -0.5 6.0
Recommended Operating Conditions
Parameter Symbol Unit Min Typ Max
Case Operating Temperature Range T
C

o
C 0 70
Supply Voltage 1 VCC3 V 3.13 3.3 3.45
Supply Voltage 2 VCC5 V 4.75 5.0 5.25
Electrical Characteristics
( Tested under recommended operating conditions, unless otherwise noted)
Parameter Symbol Unit Min Typ Max Test condition
Receiver
Output differential impedance Rout - 100 - 1
Differential data output swing Vout,pp mV 600 700 800 2
Data output rise time Tr ps 24 34 3
Data output fall time Tf ps 24 34 3
LOS Fault V V
LOS fault
Vcc-0.5 Vcc 4
HOST

LOS Normal V
LOS norm
V 0 +0.5 4
Power Supply Rejection PSR See Note 5 below 5
Note1: After internal AC coupling.
Note2: Into 100 ohms differential termination.
Note3: 20-80%
Note4: Loss of Signal is open collector to be pulled up with a 4.7k-10kohm resistor to 3.15-3.6V. Logic 0
indicates normal operation; logic 1 indicates no signal detected.
Note5: Per Section 2.7.1.in the XFP MSA Specification
Optical Characteristics
( Tested under recommended operating conditions, unless otherwise noted)
Parameter Symbol Unit Min Typ Max Test condition
Optical transmitter Characteristics
Data rate
Gbps 9.95 10.7
Receiver Sensitivity
dBm -24 Ber<10
-12,
2
31
-1PRBS
Maximum input optical Power P dBm
in-MAX
-7 Ber<10
-12,
2
31
-1PRBS
Optical Center Wavelength
c
nm 1280 1610
RTXM226-406

3
LOS De-Assert LOS dBm
D
-28
LOS Assert LOS
A
dBm -35
LOS Hysteresis dB 0.5
Bit Error Ratio BER 10
-12
2
31
-1PRBS
Block Diagram

Pin Description
Pin Logic Symbol Name/Description Note
1 GND Module Ground 1
2 VEE5 Optional -5.2V Power Supply (Not Required)
3 LVTTL-I Mod_DeSel
Module De-select; When held low allows the module
to respond to 2-wire serial interface commands

4 LVTTL-O
Interrupt

Interrupt

which can be read over the 2-wire serial interface
; Indicates presence of an important condition
2
5 LVTTL-I TX_DIS Transmitter Disable; Turns off transmitter laser output (Not Required)
6 VCC5 +5V Power Supply
8 VCC3 +3.3V Power Supply
9 VCC3 +3.3V Power Supply
10 LVTTL-I/O SCL 2-Wire Serial Interface Clock 2
11 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2
12 LVTTL-O Mod_Abs Indicates Module is not present. Grounded in the Module 2
13 LVTTL-O Mod_NR Module Not Ready; Indicating Module Operational Fault 2
14 LVTTL-O RX_LOS Receiver Loss Of Signal Indicator 2
17 CML-O RD- Receiver Inverted Data Output
18 CML-O RD+ Receiver Non-Inverted Data Output
20 VCC2 +1.8V Power Supply(Not Required)
21 LVTTL-I P_Down/RST
Power down; When high, requires the module to limit power
consumption to 1.5W or below. 2-Wire serial interface must be
functional in the low power mode.

RTXM226-406

4
Reset; The falling edge initiates a complete reset of the module including
the 2-wire serial interface, equivalent to a power cycle.
22 VCC2 +1.8V Power Supply(Not Required)
24 PECL-I RefCLK+
Reference Clock Non-Inverted Input,AC coupled on the host board (Not
Required)

25 PECL-I RefCLK-
Reference Clock Inverted Input,AC coupled on the host board (Not
Required)

28 CML-I TD- Transmitter Inverted Data Input (Not Required)
29 CML-I TD+ Transmitter Non-Inverted Data Input (Not Required)
Note1: Module ground pins GND are isolated from the module case and chassis ground within the module.
Note2: Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.

Diagram of Host Board Connector Block Pin Numbers and Names

RTXM226-406

5
Typical Application Circuit

Package Outline
WTDs XFP transceivers are compliant with the dimensions defined by the XFP Multi-Sourcing Agreement
(MSA).

Unit: mm
Tolerance: 0.1
1
5
.
8
2
.
2
5
1
.
7
1
1.9
4
.
3
4
.
2
5
44.1
1
.
4
9
8.15
8
.
5
3
62.95
1
3
.
2
18.35
6.250.05
6.9
1
8
.
3
5
1
6
.
3
5
71.1

RTXM226-406

6
Regulatory Compliance
Feature Test method Performance
Electrostatic Discharge (ESD) to
Electrical Pins
MIL-STD 883C, Method 3015.4
Human Body Model
TBD
1

Electrostatic Discharge (ESD) to
Optical Connector
IEC 61000-4-2; 1999 TBD
1

Electromagnetic Interference (EMI)
FCC Part 15 Subpart J Class B,
CISPR 22: 1997; EN 55022: 1998
Class B, VCCI Class I
Compliant with standards
NOTE 1: TBD: to be determined
Ordering Information
Part No.
Specifications
Package Data rate Detector Sensitivity Temp Others
RTXM226-406 XFP 10G APD < -24dBm 0~70
o
RoHS C

WTD reserves the right to make changes to the product(s) or information contained herein without notice. No
liability is assumed as a result of their use or application. No rights under any patent accompany the sale of
any such product(s) or information.
Edition 2009-12-01
Published by Wuhan Telecommunication Devices Co.,Ltd.
Copyright WTD
All Rights Reserved.

10gigabit XFP Optical Receiver

Uploaded by

Copyright:

Available Formats

10gigabit XFP Optical Receiver

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

10gigabit XFP Optical Receiver

Uploaded by

Copyright:

Available Formats

RTXM226-406

Wuhan Telecommunication Devices Co., Ltd.

You might also like