YETI CYCLES

600 CORPORATE CIRCLE, UNIT D

GOLDEN, CO 80401
USA
303.278.6909 / 888.576.9384
www.yeticycles.com
575 OWNERS MANUAL 07
Table of Contents
Brand Overview 6
Frame Features 8
Geometry 10
Maintenance Schedule 12
Bike Setup Overview 14
Shock Setup FOX RP23 16
Shock Setup FOX DHX Air 17
Quick Start Guide 19
Cable Routing 20
Assembly Overview 22
Assembly 24
Disassembly Tips 28
Exploded Views 20
Part List 32
Warranty 34
Contact Information 35
6 OVERVIEW
Overview
WELCOME TO THE TRIBE
Congratulations on your purchase of a new
Yeti bicycle and welcome to the Yeti Tribe. We
are condent your new bicycle will exceed your
expectations for value, performance and ride quality.
Each frame set and component has been custom
specied and designed to enhance your riding
experience. Whether you are a beginner cyclist or
a seasoned pro, Yeti bicycles will provide endless
hours of two-wheeled fun.
GENERAL INFORMATION
This model-specic manual is designed to be
used in conjunction with the general Yeti Owners
Manual and the manuals supplied by the suspension
manufacturers. If you did not receive the Yeti
Owners Manual or the manual provided by the
suspension manufacturer, download the materials
off the Internet, or contact you dealer.
Bicycling can be a hazardous activity even under
the best of circumstances. Proper maintenance of
your bicycle is your responsibility and when done
properly helps reduce the risk of injury and damage
to your bicycle. This manual outlines basic setup
and maintenance recommendations of your new
Yeti. Because it is impossible to anticipate every
situation or condition that may occur during the
assembly, setup and maintenance of your bicycle,
Yeti recommends that all service and repairs be
performed by an authorized Yeti dealer.
Warning: Make sure you review and understand the warnings, instructions and content of this manual and
accompanying manuals for your bicycle.
Warning: Technological advances have made bicycles and bicycle components more complex and the pace of
innovation is increasing. It is impossible for this manual or accompanying manuals to provide all the information
required to properly repair and maintain your bicycle. In order to help minimize the changes of injury, it is critical for you
to have work performed by an authorized Yeti dealer.
This manual contains many Warnings and
Cautions concerning the consequences of failure
to maintain or inspect your bicycle. The combination
of the safety alert symbol and the word Warning
indicates a potentially hazardous situation in which,
if not avoided, could result in serious injury or death.
The combination of the safety alert symbol and the
word Caution indicates a potentially hazardous
situation in which, if not avoided, may result in minor
injuries or damage to your bicycle or a component
of your bicycle. Be sure to read and understand all
Warnings and Cautions.
8
Frame Features
FEATURES
1. PURE TUBING
Yeti pure tubing is custom butted and tapered 7005 aluminum.
This makes the frame lightweight and strong without the use of
gussets. Unique shape provides added strength at the head tube
junctions.
2. BOTTOM BRACKET
73mm shell, for use with a 113mm spindle.
3. SEATSTAY (A) + CHAINSTAY (B)
Square seatstays are stiff and strong. Asymmetrical chainstays
provide chainring clearance and are light and strong.
Accommodates a 2.35 tire.
4. FLEX PIVOTS
CarbonFlex pivots allowed us to shave weight and increases
performance. I-Beam construction has great lateral stiffness and
enhances suspension performance.
5. SHOCK
7.875 eye-to-eye / 2 stroke.
6. DOGBONE
Dogbone controls suspension rate and enhances rear end
stiffness. Sealed cartridge bearings allow the dogbone to move
freely.
7. KNUCKLE
CNC machined knuckle junction allows for greater stand-over
clearance. This is the strongest part of the frame.
8. MAIN PIVOT
Oversized sealed bearings on main pivot for low maintenance and
stiction-free performance.
1
7
4
5
2
3b
8
3a
6
10
Geometry
GEOMETRY
GEOMETRY 575
140 MM FORK (RIDE HEIGHT 511MM) 160 MM FORK (RIDE HEIGHT 545MM)
S M L XL S M L XL
A 17.5 18.5 20.5 21.5 17.5 18.5 20.5 21.5
B 22.4 23.4 24.4 25.2 23 24 25 25.8
C 68.5 68.5 68.5 68.5 66.9 66.9 66.9 66.9
D 71.5 71.5 71.5 72.5 70.4 70.4 70.4 70.4
E 16.9 16.9 16.9 16.9 16.9 16.9 16.9 16.9
F 41.8 42.8 43.8 44.4 43.5 44.5 45.5 46.4
G 13.75 13.75 13.75 13.75 14 14 14 14
H 29.25 29.25 29.25 29.25 29.7 29.7 29.7 29.7
I 4.5 4.5 5.25 6 4.5 4.5 5.25 6
*All measurements are in inches.
C D
A
B
I
E
F
H
G
12
Maintenance
MAINTENANCE
MAINTENANCE Following these guidelines will help maintain the performance of your bicycle and prevent
more serious problems from arising. It is important to remember that service intervals can vary depending
on climate, trail conditions and riding frequency.
Caution: The torque specifcations listed should be used as a guide when performing maintenance. Technological
advances have made bicycles and bicycle components more complex, and the pace of innovation is increasing.
Because of these advances, Yeti recommends that you refer to the torque specifcations of the manufactures component
you are adjusting. In order to help minimize the chances of injury, do not perform any maintenance that you are not
confdent can be completed within your abilities.
MAINTENANCE? Not sure how to work on your own bike?
Contact your authorized Yeti dealer or visit www.parktool.com
and check out the repair help section. This section contains
detailed instruction on many of the service items listed in the
maintenance schedule.
TORQUE We have attached a brief list of torque specications for bolts and components that may need to
be tightened while performing basic maintenance. This is just a guide. For specic torque, specications,
please contact the component manufacturer directly.
TORQUE SPECS
Pivot Bolts 125 -150
Derailleur Hanger Bolts 30 -45
Handlebar Binder Bolt 150 -180
Stem Binder Bolt 175 -260
Seatpost Binder Bolt 150 -180
Saddle Clamp Bolts 175 -250
Rear Derailleur 70 -86
Front Derailleur Clamp 45 -60
Chainring Bolts 88 -132
ACTION WEEKLY MONTHLY 3 MONTHS ANNUALLY
Clean and lube chain x
Check tire pressure x
Clean bike of mud and debris (never
spray water directly into frame or
components)
x
Check brake function x
Check shock pressure, if applicable x
Check for loose bolts and tighten, if
necessary
x
Check headset and tighten / loosen, if
necessary
x
Thoroughly clean pivot points with a
rag (do not lubricate)
x
Replace brake pads, if necessary x
Check tires for wear x
Check spoke tension and retention, if
necessary
x
Check chain for worn, damaged, or
loose links, replace chain if necessary
x
Complete tune-up performed by an
authorized Yeti dealer
x
14
Bike Setup
SETUP
TOOLS NEEDED
Shock pump
Tape measure
4mm allen key
TIME
15-20 minutes
YETI TIPS
Inspect your shock for any visible damage. If
oil is leaking or you notice any damage to the
surfaces or seals, please contact the Fox Racing
Shox service center for repair at 800.FOX.SHOX.
Removing the shock from the linkage will
require the Yeti linkage tool for proper assembly
and disassembly. The tool can be purchased
online at www.yeticycles.com or through an
authorized Yeti dealer.
16
Setup-Fox RP23
SETUP SHOCK RP23
Setup-Fox DHX Air
PRO-PEDAL The pro-pedal dampening has three levels of adjustment
and is controlled by the blue lever (formerly the lock-out lever). The
three different levels of dampening are light, medium and heavy pro-pedal.
We recommend setting the pro-pedal in the middle of its adjustment
range (position 2). If you feel like the bike is too rm and is not absorbing
the small bumps, ick the lever left to the light setting. If the bike feels
sluggish and you want the suspension to feel more efcient, turn the lever
right to the stiffer setting.
AIR PRESSURE The main air spring controls the sag of the shock.
For the 575 to ride properly it is important to setup the shock with the
correct amount of sag. For general riding use 20-30% of the shock stroke
(5mm to 10mm). To increase sag reduce the main spring air pressure. To
reduce sag increase the main spring air pressure. Refer to the quick start
guide to get your starting air pressure.
SAG Once you have set your baseline air pressure you need to
measure the sag. To measure the sag slide the travel indicator
(O-Ring) up against the shock body. With a friend supporting the bike, sit
on the saddle (do not bounce) and allow your body weight to compress
the shock. Once you have compressed the shock, get off the bike and
measure the distance between the shock body and the new position of the
travel indicator (O-Ring). This is your sag. Refer to the guide below for the
percentage of sag equivalents for the measurement recorded.
Firm ride- 20-25% sag
Plush ride- 30% sag
REBOUND The rebound adjustment has a nine-click range. The
rebound knob is the red adjustment dial located above your blue pro-
pedal adjustment lever. As a general rule, adjustments that are too fast
(counter-clockwise adjustment) will produce a springy ride with excessive
kick-up of the rear end causing a bucking sensation. Adjustments that
are too slow (clockwise adjustment) will cause packing of the rear wheel
indicated by a sluggish ride feeling ride.
Slower rebound- turn the knob clockwise
Faster rebound- turn the knob counter-clockwise
4
SETUP OVERVIEW The DHX 5.0 employs both speed sensitive rebound damping and positive sensitive
compression damping. There are three external adjustments that affect the compression and one external
adjustment for the rebound. The three compression adjustments are bottom-out resistance, boost valve and
pro-pedal. The pro-pedal controls the anti-bob properties of the shock or the rst part of the shocks stroke;
the bottom-out resistance controls the end of the shock stroke; and the boost valve damping links these
two adjustments together to create a seamless transition through the entire stroke. The boost valve also
decouples the pro-pedal and bottom-out resistance making these adjustments independent of each other.
AIR PRESSURE The main air spring controls the sag of the shock.
For the 575 to ride properly it is important to setup the shock with
the correct amount of sag. For general riding use 20-30% of the shock
stroke. To increase sag reduce the main spring air pressure. To reduce sag
increase the main spring air pressure. Refer to the quick start guide to get
your starting air pressure.
Firm Ride - 20-25% sag
Plush ride - 30% sag
1
Warning: Use of the shock with improper air pressure can cause loss of
dampening and malfunction of the shock.
BOOST VALVE The DHX 5.0 has an air pressure range of 75-200 psi,
and it must be pressurized for the shock to work properly. The Boost
Valve allows the Pro-Pedal (beginning compression) and the Bottom-Out
Resistance (ending compression) to work seamlessly together. Because
of this relationship the Boost Valve pressure affects both the Bottom-Out
Resistance and the Pro-Pedal Adjustments (see adjustment relation).
Lower pressures (75 100 psi)- will decrease bottoming resistance and
lessen pro-pedal stiffness at a given setting.
Higher pressures (110 200 psi)- will increase bottoming resistance and
stiffen pro-pedal at a given setting.
Warning: Use of the shock with improper air pressure can cause a loss
of dampening and shock malfunction could occur. Do not attempt to turn the
adjuster with more than 125 psi in the chamber.
2
1
2
3
18
Setup-Fox DHX Air
SETUP DHX AIR
Quick Start Guide
WHAT IS PRO-PEDAL? Pro-pedal is a compression tune that
gives the right amount of low-speed compression to lter out
unwanted rider-induced bob without sacricing critical mid-
and high-speed damping. No ushing through your travel,
no wasted setup time, and no energy-sucking suspension
movement. Just super efcient pedaling performance ready
for hits of any size.
SAG Once you have set your baseline air pressure you need to
measure the sag. To measure the sag slide the travel indicator
(O-Ring) up against the shock body. With a friend supporting the bike, sit
on the saddle (do not bounce) and allow your body weight to compress
the shock. Once you have compressed the shock, get off the bike and
measure the distance between the shock body and the new position of the
travel indicator (O-Ring). This is your sag. Refer to the guide below for the
percentage of sag equivalents for the measurement recorded.
3
REBOUND The rebound adjustment has a nine click range. As a
general rule, adjustments that are too fast (counter-clockwise) will
produce a springy ride with excessive kick-up of the rear end. Adjustments
that are too slow (clockwise) will cause packing of the rear wheel and give
the bike a sluggish feel.
S lower rebound - turn the knob clockwise
Faster rebound- turn the knob counter-clockwise
BOTTOM-OUT RESISTANCE The bottom-out adjuster has three
full turns of adjustment. This adjustment controls the bottom out
resistance of the shock, or the compression on the nal part of the shocks
stroke. If you feel like you are bottoming-out the shock on big hits, you can
minimize this sensation by increasing the bottom-out resistance.
More resistance- clockwise rotation
Less resistance- counter-clockwise rotation
The adjuster can be turned by hand or with a 4mm allen key. The allen key
should be placed into one of the holes on the perimeter of the adjuster.
PRO-PEDAL The pro-pedal adjustment has a 15 click range of
adjustment. The pro-pedal dampening affects the rst half of stroke
where most rider induced bob occurs.
More Damping - clockwise rotation
Less Damping - counter-clockwise rotation
5
4
6
QUICK START GUIDE RP23 575
AIR SPRING SETTINGS
Rider Weight lbs 125 135 145 155 165 175 185 195 205 215
Air Pressure (psi) 135 145 155 165 175 185 195 205 215 225
*EXTERNAL ADJUSTMENTS
Rebound 4 Clicks
Pro-Pedal Lever ON
Pro-Pedal Knob Level 2
SAG SETTINGS
Sag % 20 25 30
Measured (mm) 10 12.5 15
QUICK START GUIDE DHX AIR 575
AIR SPRING SETTINGS
Rider Weight lbs 125 135 145 155 165 175 185 195 205 215
Air Pressure (psi) 145 155 165 175 185 195 205 215 225 235
Boost Valve Settings 109 116 124 131 139 146 154 161 169 176
*EXTERNAL ADJUSTMENTS
Rebound 10 Clicks
Bottom-Out Resistance 1.5 Turns
Pro-Pedal 5 Clicks
SAG SETTINGS
Sag % 20 25 30
Measured (mm) 10 12.5 .15
*All clicks are clockwise rotation from all the way out
or a full counter-clockwise position.
20
The 575 has full cable housing. By using full cable housing, we have eliminated break points in the line
of your shifter housing. This allows riders to experience better overall shifting performance by reducing
the entrance of unwanted elements such as sweat and sediment. Use of full cable housing helps prevent
corrosion from the elements and keeps the shifting smoother for a longer period of time.
Cable Setup
SETUP HOUSING
HOUSING END CAPS Yeti recommends using metal end caps
to maintain the integrity of the housing. The metal caps do not
allow the cable to pull through as do the plastic versions. Do
not mix up the shift and brake housing because it will result
in a loss in performance.
Caution: The failure to properly route shifter housing can cause malfunction of the shift mechanism and unexpected
shifting of gears.
REAR DERAILLEUR Fit the housing from the rear shifter across the
head tube and down the cable drop outs. There are three cable drop
outs groups on the non-drive side of the down tube to which the housing
and brake line can be attached. Fit the rear housing along the down tube
into the drop outs that are for the rear brakes.
The routing of the housing around the bottom bracket is a little tricky. The
shifter housing is looped over the bottom bracket shell and then passed
over to the drive side chainstay. The nal stretch of rear derailleur housing
is attached using c-clips on the drive side chainstay and looped into the
derailleur.

FRONT DERAILLEUR Fit a piece of housing form the front shifter
across the head tube into the rst cable stop on the drive side of the
top tube.
The cable runs parallel along the drive side of the down tube and then
slides into the cable guide under the bottom bracket shell. Sometimes the
plastic guide from the front derailleur is oriented incorrectly. The cable
should run thru the long guide. This should be positioned on the drive side
of the bike closest to the crank. Make sure cable does not make contact
with frame.
REAR BRAKE The rear brake loops across the head tube and into
the cable drop outs on the non-drive side of the down tube. Use the
plastic c-clips to secure brake line to your frame. Then the attached line is
to the open stops on the top of the non-drive chainstay. Make sure the line
is on the inside of the seatstay when attaching the caliper body.
Note: This will prevent the brake line from being compromised if the bike
or rider falls.
1
2
3
22
Assembly
ASSEMBLY
TOOLS NEEDED
Warning: Service on Yeti bicycles requires special
knowledge and tools. Yeti Cycles recommends that all
service and repairs be performed by an authorized Yeti
dealer.
Dead blow hammer
Adjustable pliers
Two - 5mm allen keys
6mm allen key
4mm allen key
4mm t-handle allen key
8mm allen key or 5/16 guide
Linkage tool
TIME
30-45 minutes depending
on condition of the bike
YETI TIPS
Make sure your tools are in good condition.
A worn allen key can round the hex on a bolt
preventing proper torque. Be careful when using
ballpoint allen wrenches for the same reason.
Torque settings are listed throughout the
instructions. It is also important to prep all bolt
threads. The instructions denote whether to use
a blue Loctite compound or grease.
The linkage tool is necessary to properly
disassemble and reassemble the linkage. Using
a hammer to tap out the pin can cause damage
to the linkage and shock.
Not every tool may be needed for the assembly /
disassembly of your bike. The list encompasses
all the tools necessary to completely assemble
and disassemble each bike.
24 ASSEMBLY
Assembly
LINKAGE ASSEMBLY The procedure in step two produces a relief,
shown on the right, that aids in the assembly.
LINKAGE ASSEMBLY Place two of the dogbone bearings (300020029)
and the 1.38 steel pin onto the threaded bolt as shown. Now put on
the linkage tool washer and nut (200020071). At this point tighten down the
assembly with two 1/2 inch wrenches.
LINKAGE ASSEMBLY Slide one of the black nylon washers
(300030100) onto the steel pin ush against the inside edge of the
bearings.
LINKAGE ASSEMBLY Place the dogbone over the shock with the
counter-bored holes facing out, what would be back towards the
seat tube, and the threaded end facing towards the shock. Slide the pin
subassembly into the shock eyelet as shown.
Tip: You will need to press evenly using your body weight in order for the
steel pin to slide through the garlock bushing in the shock eyelet.
LINKAGE ASSEMBLY Once you have the pin subassembly started
into the shock eyelet, you can slide the threaded bolt, press-cup
and press-cup insert conguration from step one through the steel pin
subassembly and shock. On the opposite end of the bolt, slide a second
nylon washer, the remaining two bearings, press-cup insert, press-cup,
washer and nut.
THREAD PREP Yeti recommends prepping all bolt threads
at once on your work bench with Loctite or grease. This will
ensure that all bolts are used in assembly. The medium
strength (blue) Loctite formula along with proper torque is
ideal to keep the bolts snug.
LINKAGE ASSEMBLY Slide a washer, press-cup and press-cup insert
onto the threaded bolt of you linkage tool.
LINKAGE ASSEMBLY Use two 1/2 wrenches and torque the linkage
together until the bearings press into position. Make sure bearings
are ush on both sides of dogbone. This will ensure proper alignment of the
swing arm once it is installed.
LINKAGE ASSEMBLY Insert the small socket head cap screws
(300030056) into the dogbone and torque down with a 2.5mm allen
key. Make sure to prep the bolts with Loctite.
Torque spec: 125-150 inch/pounds.
7
8
1
3
2
4
5
6
nylon washers
26
Assembly Cont.
ASSEMBLY
FRAME ASSEMBLY First slide the swing arm over the main pivot
as shown, notice the recess cut in the swing arm in front of the
bearings. The recess should be lined up over the main pivot lip to ease the
installation process. Slide the seatstays over the steel pivot pin. Now slide
the 41.2mm female Yeti bolt and washer through the seatstays and shock
assembly. Place a male Yeti bolt with a washer on the non-drive side of the
bike. Tighten down both Yeti bolts with 5mm allen keys.
Note: Assemble this rst so the seatstays dont hit the frame when
hammering in the main pivot pin.
FRAME ASSEMBLY Make sure the bearings are lined up with the main
pivot before tapping the lightly greased main pivot pin through the
frame with the dead blow hammer.
Tip: Use your left index ner to align the main pivot while installing.
FRAME ASSEMBLY Install the black washer and button head bolt over
the main pivot pin as shown. Cinch the button head down with a 5mm
allen key while holding the main pivot with 6mm allen key.
The last step is to install the derailleur hanger and water bottle bolts.
13
FRAME ASSEMBLY Place the shock assembly onto the bike in the
conguration shown to the right. Slide your rst 33mm female bolt
and washer through mounting position one to hold the shock assembly in
place. Now swing the dogbone into mounting position two. Slide the other
22mm female Yeti bolt and washer through the mounting hole of the bike.
Tap the 22mm female Yeti bolt into position with the dead blow hammer.
Note: All female bolts and the main pivot are installed from the drive side
of the bike.
FRAME ASSEMBLY Thread the male Yeti bolts into the 22mm female
bolts and tighten down with 5mm allen keys.
Note: The shoulder on the bolt should not be visible. The bolt should
t ush against the frame. Be careful when tightening, make sure the
shoulder of the male bolts do not bind or bend the washers.
.
11
12
9
10
28
Disassembly Tips
DISASSEMBLY
FRAME DISASSEMBLY To remove the main pivot pin, place a 5mm
allen key on the button head bolt and a 6mm allen key on the main
pivot pin. Turn counter-clockwise until the button head is removed. Then
take 8mm allen key or a punch and tap out the main pivot pin with a dead
blow hamemr.
Note: Disassemble this rst so that the seatstays dont hit the frame when
hammernig out the main pivot pin.
FRAME DISASSEMBLY Now remove the male and female Yeti bolts
that attach the seatstays to the shock and dogbone. You will need two
5mm allen keys in order to back off these bolts. Your swing arm should now
be free to slide off the front triangle.
FRAME DISASSEMBLY To remove the shock mounting bolts, place a
5mm allen key on both ends of the bolts and turn counter-clockwise.
Once the male Yeti bolt is removed, take a 6mm allen key and tap out the
female end.
Note: This methods works for all three mounting bolts on a Fox Racing
Shock.
FRAME DISASSEMBLY Use a 2.5mm allen key to loosen the socket
head cap screws from the dogbone.
3
4
1
2
FRAME DISASSEMBLY Slide a washer and removal slug onto the
threaded bolt. Slide this subassembly through the shock and dogbone.
On the opposite end, slide on the catch sleeve, washer and then thread the
nut on.
Use two 1/2 and adjustable wrenches and torque down until the removal
slug presses the steel pin out of the dogbone bearing assembly.
5
30
Exploded Views
EXPLODED VIEWS
REBUILD KITS The individual components of each Yeti bike
are not sold separately. All Yeti parts are sold in rebuild kits
listed below. Each and every part can be obtained by purchas-
ing one of the rebuild kits. Cross reference the part number
you desire from the parts lists.
PARTS LIST W/FOX SHOCK
QTY. PART # DESCRIPTION
1 1 NA Front Triangle
2 1 NA Swingarm
3 1 NA Rear Shocl
4 2 300020020 Fox Garlock
5 2 300020034 Reducer- 22mm (front)
6 1 300040210 2007 575 Dogbone
7 1 300030085 Pivot Pin (M6 x 17 x 52.4mm)
8 1 300030087 Pin- Steel Shock- 1.38 ASR 2
9 1 300030015 Bolt- Pivot (8 x 41.2mm)
10 2 300030077 Yeti Pivot Bolt Female (M6 x 1 x 24.8mm)
11 3 300030078 Yeti Pivot Bolt Male 17mm
12 1 300030006 Bolt Button HD (M6 x 1 x 12mm)
13 1 300030045 Main Pivot Washer
14 6 300030069 Washer (8.5 x 12.5 x 0.5mm)
15 2 300030100 Washer Blk Nyl 0.7 x 0.51 x 0.061
16 2 300020001 Bearing 6903 Max
17 4 300020029 Bearing 0.75 x 0.5
18 2 300020026 Bearing 16 x 8 x 5mm w/ Ext Race
19 2 300020027 Bearing 16 x 8 x 5mm
20 1 300060045 Derailleur Hanger w/ Fasteners
21 2 300030056 Bolt Cap (M3 x 0.5 x 12)
N/A 4 300030010 Bolt-Cap H20 (M5 x 0.8 x 16mm)
21
1
2
3
4
5
5
4

7
8

10
10
11
11
11
12
13
14
14
14
14
14
14
15
15
1
1
17
17
17
17
18
18 1
1
20
20
20
21
2007 575
32
Parts List
PARTS LIST
PART NUMBER DESCRIPTION QTY. PART NUMBER DESCRIPTION QTY.
300030006 BOLT-BUTTON HD M6X1X12 5MM HEX 1
300030087 PIN - STEEL SHOCK - 1.38 ASR 2 1
300030100 WASHER- BLK NYL .70X.51X.061 4
200020071 LINKAGE TOOL 1
300030107 BOLT G5 5/16-24X6.5 4
300030126 MACHINE PARTS FOR TOOL 1
300030105 FINISHED HEX NUT 5/16-24 1
300030087 PIN- STEEL SHOCK- 1.38 ASR 2 1
200020066 575 04-07 DOGBONE PLUS BEARINGS 1
300020027 BEARING 16MMX8MMX5MM 2
300020026 BEARING 16MMX8MMX5MM W/EXT RING 2
300020029 BEARING .75X.5 4
300040210 DOGBONE- 575 1
300030056 BOLT CAP M3X0.5X12 2
300030100 WASHER- BLK NYL .70X.51X.061 2
200020073 575 04-07 FOX MOUNTING HARDWARE 1
300030087 PIN - STEEL SHOCK - 1.38 ASR 2 1
300030078 PIVOT BOLT MALE YETI 17MM 1
300030015 PIVOT BOLT - 8X41.2MM 1
300030069 WASHER SS 8.5MM ID 12.5MM OD 2
300030100 WASHER- BLK NYL .70X.51X .061 2
200020065 575 04-07 BEARING REBUILD KIT 1
300030100 WASHER-BLK NYL.70X.51X.061 2
300020027 BEARING 16MMX8MMX5MM 2
300020026 BEARING 16MMX8MMX5MM W/EXT RING 2
300020029 BEARING .75 X .5 4
300020001 BEARING 6903 MAX 2
300030006 BOLT-BUTTON HEAD M6X1X12 5MM HEX 1
300030092 HAT-O-RING-PIN - PROG AIR SHOCK 2
300030090 PIN - PROGRESSIVE AIR SHOCK 1
300030094 O-RING - PROGRESSIVE AIR SHOCK 2
300030100 WASHER- BLK NYL .70X.51X.061 2
200020063 575 04-07 MASTER REBUILD KIT (W/FOX MOUNTING HARDWARE) 1
300020027 BEARING 16MMX8MMX5MM 2
300020026 BEARING 16MMX8MMX5MM W/EXT RING 2
300020029 BEARING .75 X .5 4
300020001 BEARING 6903 MAX 2
300030015 BOLT- PIVOT BOLT- 8X41.2MM 1
300030077 PIVOT BOLT FEMALE YETI 24.8MM 2
300030078 PIVOT BOLT MALE YETI 17MM 3
300030069 WASHER SS 8.5MM ID 12.5MM OD 6
300030179 WASHER- CUSTOM PIVOT PIN- 7075 1
300030085 PIVOT PIN- AL- 17MMX52.4MM 1
34
Warranty
WARRANTY
YETI LIMITED (2) TWO YEAR FRAME WARRANTY (applies to 303, 4X, DJ)
Yeti Cycles will repair or replace, at its option, any frame it determines to be defective materials and / or
workmanship. The (2) two year limited warranty is conditioned upon the bicycle being ridden under normal
conditions and having been properly maintained. This warranty does not apply to the components attached
to the frameset such as suspension components, wheels, drive train, brakes, seatpost, handlebar and stem.
This warranty applies only to the original owner and is non-transferable. This warranty is void if the bicycle
was not properly assembled by an authorized Yeti dealer.
YETI LIMITED (5) FIVE YEAR FRAME WARRANTY (applies to AS-R sl, AS-R Carbon, 575, ARC, ARC-X)
Yeti Cycles will repair or replace, at its option, any frame it determines to be defective materials and / or
workmanship. The (5) ve year limited warranty is conditioned upon the bicycle being ridden under normal
conditions and having been properly maintained. This warranty does not apply to the components attached
to the frameset such as suspension components, wheels, drive train, brakes, seatpost, handlebar and stem.
This warranty applies only to the original owner and is non-transferable. This warranty is void if the bicycle
was not properly assembled by an authorized Yeti dealer.
ADDITIONAL CONDITIONS
These limited warranties do not apply to normal wear and tear, nor to claimed defects, malfunction or
failures that result from abuse, neglect, improper assembly, improper maintenance, alteration, collision,
crash or misuse. The original owner shall pay all labor charges connected with the repair or removal of all
components. Under no circumstances does this limited warranty include of the cost of travel or shipment to
and from an authorized Yeti dealer. In order to exercise your rights under these limited warranties, the bicycle
or frameset must be presented to an authorized Yeti dealer, together with proof of purchase.
The above warranties have been in effect since January 2000. All Yeti frames sold prior to that date
had a limited (1) one year warranty on the frameset.
No Fault Replacement Policy
Yeti Cycles will make replacement parts available at a minimum charge to the original owner in the
event of a crash or any other non-warranty situation. Yeti Cycles does this at its sole discretion and
reserves the right to refuse this offer.
If you have a warranty concern, please contact your authorized Yeti dealer.
NO FAULT REPLACEMENT POLICY
Yeti Cycles will make replacement parts available at a minimum charge to the original owner in the event of a
crash or any other non-warranty situation. Yeti Cycles does this at its sole discretion and reserve the right to
refuse this offer. If you have a warranty concern, please contact you authorized Yeti dealer.
PRODUCT LIFE CYCLE
Every Yeti frameset has a useful product life cycle. The length of that useful product life cycle will vary
depending on the construction and materials of the frameset, maintenance and care the frameset receives,
and the amount and type of use the frameset is subjected to over its life. Yeti recommends that an authorized
Yeti dealer should inspect the frame for stress annually. Frame stress could cause potential failure and the
signs are usually apparent in the form of cracks, fracture lines, deformation, dents and other visual indicators
of abnormality. These safety checks for frame stress are important to prevent accidents, injury to the cyclist
and product failure of a Yeti frameset.
DISCLAIMER
Yeti Cycles is not responsible for any damages to you or others arising from riding, transporting or other
use of your bicycle. In the event that your frame breaks or malfunctions, Yeti Cycles shall have no liability or
obligation beyond the repair or replacement of your frame pursuant to the terms outline in this warranty.
CONTACT INFO
Yeti Cycles
600 Corporate Circle, Unit D
Golden, CO 80401
(p) 303-278-6909
(f) 303-278-6906
WWW.YETICYCLES.COM
BUSINESS HOURS
Monday-Friday
8AM-11:30AM, 1:00PM-5:30PM
(Mountain Time)