Security Analysis of LTE Access Network: Abstract: The Latest Technological Development in Mobile

Security Analysis of LTE Access Network
Cristina-Elena Vintil, Victor-Valeriu Patriciu, Ion Bica

Computer Science Department
Military Technical Academy - Bucharest, ROMANIA
[email protected], [email protected], [email protected]

Abstract: The latest technological development in mobile
telecommunications is the 4G architecture. Developed and
standardized by the 3GPP, this technology proposes significant
throughput and security enhancements in comparison with its
predecessor, 3G a 3GPP architecture, as well as with the non-
3GPP solutions like WiMAX. Besides the enhancements
mentioned above, 4G is a simplified network architecture, flat-IP
topology and services-oriented. One of the major simplifications
is the base-station architecture, called eNodeB in the 4G
terminology, which eliminates the need for a radio resource
controller and assumes signaling, control-plane and security
functions. It is the mobile device connection to the network and
the proxy of all its traffic. This is why the access network is one of
the most important areas for network design and optimization
and also for security in term of access control, authentication,
authorization and accounting. This paper reviews the access
network components, the eNodeB security requirements, as
defined by 3GPP and analyzes two secure access mechanisms to a
4G network, one via eNB (3GPP access type) and the other one
via AP (non-3GPP access type). It also proposes an improvement
to the AKA protocol in order to obtain better security.
Keywords-SAE; LTE; EPC; security; eNodeB; shared-secret;
HSS; Diameter; EAP; AKA; J-PAKE

I. INTRODUCTION

The most important and influential telecommunications
organizations around the Globe are part of the 3GPP society
[20]. The latest technological design for mobile
telecommunications that appears to be the future
communications architectural baseline is the 4G architecture,
also called SAE (System Architecture Evolution). SAE
comprises the radio access network, usually referred to as LTE
(Long Term Evolution) and the EPC (Evolved Packet Core)
the core network of this design, a flap-IP network, highly
optimized and secure network, oriented on services.
The figure below describes one of the most common
architectural design views, a non-roaming architecture with a
4G mobile device and only 4G access to the network. The
entities that appear in this case are the UE (User Equipment),
the eNodeB (the antenna), the MME (Mobility Management
Entity), the SGW (Serving Gateway), PGW (PDN (Packet
Data Network) Gateway), HSS (Home Subscriber Server),
PCRF (Policy Charging Rules Function) and a 3G access
network where the UE can roam to. This also represents the
naming of the interfaces that connect these entities.

Figure 1. Basic 4G Core Network Architecture

The UE connects to the 4G network by signaling its
presence in the eNodeB cell. The cell selection prerequisites
are described in [3], [4] and [5]. The process by which an UE
chooses a certain antenna (eNodeB) to connect to is called
camping the UE camps on a cell. The best situation for an
UE is to find a so-called suitable cell to camp on. This suitable
cell is a cell that meets the following requirements: it is part of
the selected PLMN (Public Land Mobile Network), part of a
registered PLMN or part of the Equivalent PLMN list as per
the most recent update from the NAS. Also, the cell should not
be barred, not reserved and should not be in the list of
forbidden areas for roaming. Once these criteria are met, the
UE sends an Attach Request message to this eNodeB, asking
to attach to the network. This message flows over the LTE
29
ICN 2011 : The Tenth International Conference on Networks
Copyright (c) IARIA, 2011 ISBN:978-1-61208-113-7

radio interface, reaches the eNodeB, and then the eNB sends
this message to the MME via the S1-MME interface. The
MME verifies the validity of the UE request against the HSS
credentials, then selects an appropriate SGW that has access to
the PLMN requested by the UE. The PLMN where the UE
connects is identified by a string called APN (Access Point
Name) preconfigured on the USIM. Once the access request
reaches the PGW which is the UEs anchor point to the
desired PLMN, the request is replied with an IP address
suitable for this connection and, even more, after interrogating
the PCRF about this UE, the PGW may create dedicated
bearers for this UE immediately after attach. The decisions on
the way are detailed in Section 4.3.8 of [1], which describes
the selection functions of each of the core-network entities.
Briefly, the HSS drives the selection of the SGW and the
SGW on its turn, selects the PGW, based mostly on
information already decided upon by the HSS. The MME is
selected based on the network topology, the eNB trying to
select the MME that minimizes the probability of doing
handovers and that provides load balancing with other MMEs.
The Initial Attach process starts with the Attach Request
message sent by the UE to the eNB selected. This message
contains, among other parameters, the IMSI (International
Mobile Subscriber Identity) or the old GUTI (Global Unique
Temporary Identity), the last TAI (Tracking Area Identifier) if
available, PDN Type, PCO (Protocol Configuration Options),
Ciphered Options Transfer Flag, KSI-ASME (Key Set
Identifier - Access Security Management Entity), NAS
(Network Access Server) Sequence Number, NAS-MAC,
additional GUTI and P-TMSI (Packet - Temporary Mobile
Subscriber Identity) signature.
The PCO means that the UE wants to send some
customized information to the network (the PGW may not be
in the visited network also), indicating for instance that the UE
prefers to obtain the IP address after the default bearer has
been activated. If the UE intends to send authentication
credentials in the PCO, it must set the Ciphered Options Flag
and only send PCO after the authentication and the NAS
security have been set up completely. From now on, it is the
responsibility of the eNB to proxy the UEs message to the
MME. And, once the UE is authenticated, the eNB is also the
one responsible of establishing security connections with the
UE and the core network in order to protects the UEs traffic
at the radio/ethernet border. Being at the border between these
two topologies, the eNB is exposed to the security issues
arising from both the radio and the IP networks.

II. SECURITY ARCHITECTURE
The 4G architecture defines, in [6], the five main areas
concerned with the Security of this design. The first is called
Network Access Security and it refers mostly to the radio
attacks. The second one is the Network Domain Security and
it defines the requirements and rules to prevent attacks over
the wire, when exchanging control-plane and user-plane. The
third is User Domain Security, dealing with securing the
access to mobile terminals, the fourth is the Application
Domain Security which standardizes the set of rules for
secure message exchange between applications on clients and
servers. The fifth domain defined by this standard is the
Visibility and Configurability of Security set of features that
informs the user about a particular security feature and
whether this feature is applicable or not to the services this
user is trying to access.
The standard [6] describes in Section 5.3 the security
requirements necessary for a secure eNB operation
environment, as well as for secure eNB functioning. It
nevertheless leaves these specifications at a requirements
level, permitting the operator to implement the exact protocols
he considers for his network; these protocols are compliant to
the standard as long as they meet the security requirements
defined here, in Sections 11 and 12. The principles are that the
eNB should have a mean of securing the cryptographic keys
and information inside the device, it should have secure
communication links both over the air with the UE and with
the MME (via the S1-MME interface), SGW (via the S1-U
interface) and other eNBs (via the X2 interfaces, if they exist)
for control-plane and user-plane traffic. Also, if the operator
has a securely contained environment where these
communications happen, he may not implement any precise
security measure for the requirements defined here.
The access to a 4G network is done in many ways, most
importantly driven by the type of radio medium in place. The
most usual procedure is the AKA (Authentication and Key
Agreement) Procedure. This happens when the access medium
is LTE. The AKA procedure is described in the figure below.

Figure 2. AKA Exchange

The MME here is the authenticator, while the HSS is the
authentication server. The communication between the MME
and the HSS takes place over S6a and it uses Diameter as a
30

protocol. The UE (the mobile terminal) has a UICC (Universal
Integrated Circuit Card) inside. This circuit stores the K, a
shared key located as well on the AuC (Authentication Center)
entity part of the HSS. The authentication in 4G is not natively
implemented over a PKI infrastructure; it uses the shared-
secret symmetric authentication inherited from the 3G UMTS
systems, with some improvements.
The purpose of the AKA mechanism is to create keying
material for the RRC (Radio Resource Control) signaling,
NAS (Non-Access Stratum) signaling and for the user-plane,
both ciphering and integrity keys. The first NAS message may
be an Attach Request, a Service Request or PDN Connectivity
Request message. This message reaches the MME, which
should verify the UEs identity. If the UE is new to this
network entirely, then the MME asks the UE for its permanent
identity the IMSI. This is considered a security flaw and it is
not yet addressed. But, if the UE is not new to this network,
but rather reached this MME by means of a TAU (Tracking
Area Update) procedure, then this MME should have a GUTI
in the message received from the UE. This MME then sends
the GUTI and the full TAU message to the previous (old)
MME, and this one replies with the actual permanent UE
identity the IMSI and the authentication data for it. The
message exchange between the two MME entities takes place
over the S10 interface. Also, if the UE roamed to this MME
from a 3G network, the current MME tries to connect to the
previous management entity of this UE, the (old) SGSN
(Serving GPRS Gateway) via the S3 interface and get the
IMSI information from there. Otherwise, it tries to derive it
and then connects to the HSS via the S6a interface and verifies
that the IMSI this UE utilizes is actually valid for this network
and may have permission to attach. This message is a
Diameter message described in [9].
The HSS gets the AV (Authentication Vector) set and
sends it to the MME. This EPS-AV consists of RAND,
AUTN, XRES and K-ASME and the HSS, entity that is also
called UEs HE (Home Environment) may send multiple sets
of AVs to the MME currently serving the UE. The standard
recommends that the HSS sends only one set of AVs, but in
case it still sends multiple sets, there should be a priority list
which the MME should use.
A major improvement when comparing EPS-AKA to
UMTS-AKA is that the CK and IK keys never actually have to
leave the HSS. The UE signals in its initial message the type
of access network he used. If this is E-UTRAN, then a flag
called AMF is set to value 1, and this instructs the MME and
ultimately the HSS to only send the K-ASME key in the AV
reply (along with RAND, AUTN and XRES), but not the CK
and IK as well. Also, this K-ASME can be stored in the MME,
so, when re-synchronizing the UEs status, the full AKA
process may not even have to take place. The MME sends the
RAND and AUTN to the UE, then it waits for the response.
Here, the eNodeB just forwards these messages back and
forth, not participating effectively in the cryptographic
exchange. Unlike the GSM, where only the network was
authenticating the UE, but not viceversa, the EPS-AKA
provides mutual authentication between the UE and the
network. Upon receipt of the message, the UE can verify,
based on the AUTN, the validity of the reply, computes the
RES and sends this message to the MME. The MME verifies
whether XRES equals the RES and if they are the same, the
UE is authenticated. As described, the CK and IK are
computed by UICC and HSS independently, they are never
sent over the wire in EPS. Also, the HSS sends initial keys to
MME and eNB, which are then used by these entities to derive
actual keys for NAS, user-plane and RRC traffic.
The figure below depicts two flows: the first one
represents the sending of the IMSI in clear-text over the
network (the case of the first attach of this UE to the network
or when the new MME cannot locate the previous MME) and
the second one represents the message exchange between the
two MMEs.

Figure 3. Message exchanges to locate the IMSI

The key hierarchy in 4G is more complicated than in 3G,
but it assures this way the protection of the master keys and it
also reduces the need for periodic updates, re-generation and
transmission of the master keys. There are also special cases
for TAU and handover types and also for re-keying that may
require special attention, and they are described in [6].
For the non-3GPP access types, the 4G architecture no
longer uses the AKA mechanism, but a variation of the EAP
with AKA: EAP-AKA (Extensible Authentication Protocol)
mechanism. This assumes the presence of a EAP capable
phone, the Access Point, which connects to the AAA
(Authentication, Authorization, Accounting) server via the Wa
interface and the AAA server connects to the HSS via the Wx
interface. The EAP-AKA message flow is represented in the
picture below. The EAP is a Request/Response type of
protocol. When the AP detects the presence of the USIM, it
sends this mobile an EAP Identity Request message. The
USIM sends back its NAI (Network Address Identifier), which
is similar to an e-mail address RFC 822. The AP forwards
this NAI to the 3GPP AAA Server based on the domain name
which is part of the NAI this happens over the Wa interface.
31

Then the AAA server verifies whether it has a valid and
unused AV for this USIM. If so, it sends this AV and AKA
Challenge for the USIM, back to the AP. If there is no
available AV for this USIM, the AAA server contacts the HSS
server via the Wx interface, retrieves the AV and then
continues to the AKA Challenge. The rest of the process is
similar to the EPS-AKA, with the only observation that it
takes place over the EAP framework.

Figure 4. EPS EAP-AKA exchange

When comparing pre-4G authentication methods, there
are several aspects that may be observed. One of them is the
authentication method. This is very similar for 3G (UMTS),
3.5 G (HSDPA) and 3.75G (HSDPA+), as all of them use the
AKA mechanism. The differences appear in the actual
implementation: the 3G implementation specifies that the CK
and IK keys from the AuC (Authentication Center) part of the
HE (Home Environment) are actually being sent to the SGSN
at the moment the SGSN downloads the Authentication
Vectors from this database. This never happens in 4G, where
the key hierarchy is more complicated and the only key
downloaded from the HSS to the MME is the K-ASME key.
This is also a security improvement in 4G in comparison to
3G, because the CK and IK keys should not leave the AuC,
but only be derived independently by the UICC and HSS. In
both 3G and 4G security architectures, there are multiple AVs
(Authentication Vectors) available in the authentication part of
the subscribers database. All these authentication vectors may
be downloaded initially by the authentication entity (SGSN,
MME respectively), a certain AV being used for a single
round of authentication. The order in which these AVs are
used is determined in both architectures by a sequence
number. The CK||IK pair is derived by the UICC in 3G, and
the SGSN only selects this pair from the authentication data
received from the AuC. In 4G, the MME receives only its K-
ASME from the HSS, and it then derives, together with the
UE, the K-NASint and K-NASenc from the K-ASME. The
following figure describes the key hierarchy in the 4G
architecture.

Figure 5. EPS key hierarchy [6]

The keys derived in the classical 4G AKA procedures are
the following: K-NASenc (encryption key for NAS traffic), K-
NASint (integrity key for NAS traffic), KeNB (derived by
MME and eNB), KUPenc (encryption key for the user-plane
data, derived by MME and eNB from KeNB), KRRCint and
KRRCenc (integrity check, respectively encryption key
derived by MME and eNB from KeNB, used for securing the
Radio Resource Control traffic).
The sections in this figure describe which entities are
involved in a particular key generation process; there are 6
keys derived from the EPS authentication mechanism. This
key generation feature introduced in 4G improves the speed of
the re-authentication procedures and also the refreshing
process of the keys. As the K-ASME may be used a master
key in further service requests authentication, the MME no
longer has to download the authentication data from the HSS
and it can also avoid re-synchronization issues. HSDPA and
HSDPA+follow the 3G procedures and mechanisms.
The entire authentication information that is stored in the
UICC and its corresponding associates from the network side
is called security context; a security context consists of the
NAS (Non Access Stratum) and AS (Access Stratum) security
contexts. The AS security context has the cryptographic keys
and chaining information for the next hop access key
derivation, but the entire AS context exist only when the radio
bearers established are cryptographically protected. The NAS
context consists of the K-ASME with the associated key set
identifier, the UE security capabilities and the uplink and
downlink NAS count values, used for each EPS security
context. The 3G architecture also has the concept of security
contexts, and this becomes very important when 3G and 4G
devices and network entities interoperate. A 3G device that
was initially attached to a 3G network has received a set of
security content that is stored in the UICC. This information is
considered a partial and legacy security context in the 4G
environment. For a security context to be considered full, the
MME should have the K-NASenc and K-NASint keys, which
are obtained when the 3G device handovers to the 4G
network. In this handover case, the legacy security context is
32

referred to as mapped security context. A NAS security
context of a mapped security context is always full and it is
current (which means it is the most recently activated context).
A summary of the types of security contexts that exist in the
3G 4G interoperation is in the following table.
TABLE I. TYPES OF SECURITY CONTEXTS
AGE/EFFECT CURRENT NON-CURRENT
FULL NATIVE / MAPPED NATIVE
PARTIAL X NATIVE

A native security context is the one established at the
EPS-AKA procedure successful completion.

III. SECURITY ISSUES AND ASSESSMENT
The security analysis in a mobile network expands from the
radio access network until the core network and services. The
most common threats are related to the following security
prerogatives:
- authentication: the network must be sure that the
person accessing a certain service is the one
pretending to be and paying for this service
- confidentiality of data: the user and the network must
be sure nobody un-authorized is viewing or accessing
the users data
- confidentiality of location: the users location must
not be known by anybody un-authorized
- denial of service: the user and the network must be
sure that nobody interferes with a users session, nor
high-jacks it
- impersonation: the network and the user must be sure
that no other user is pretending to be the actual
registered user, nor this user can access services
available to the actual registered user
The EPS security mechanisms should be able to
enforce the above principles, and everything starts with the
access level. The NDS (Network Domain Security) enforces
these principles as well, but at a different level. When talking
about User Domain Security, the Access Level is the first line
of defense against attacks. For this, the EPS provides mutual
authentication via the EPS-AKA mechanism or EPS-EAP-
AKA (for non-3GPP access types). Using the keys generated
after the AKA mechanism, all the RRC, NAS and user-plane
signaling and data-planes are protected by secure
encapsulation and integrity protected. Even though a flaw of
the EPS-AKA: the transmission of the permanent identity
IMSI over the air at Initial Attach exchange, EPS implements
the GUTI value that is sent over the air instead of the IMSI, so
that the AKA mechanism also provides identity protection.
The only cases that require the transmission of the IMSI are
the first Initial Attach and the attach after the core network
entities are de-synchronized. This vulnerability opens the door
for a man-in-the-middle attack that can take place once the
IMSI is captured. Another vulnerability identified within the
EAP-AKA, but that manifests in consequence with EPS-AKA
also is the lack of PFS support. The PFS Perfect Forward
Secrecy is an attribute of the mechanisms that assures the
secrecy of a set of session keys even if a previous set of keys
has been compromised.
A solution for the PFS vulnerability can be the use of an
algorithm that has the PFS built-in. This algorithm is the
Diffie-Hellman key exchange. Still, DH does not provide
mutual authentication by itself. Another algorithm, based on
the J-PAKE mechanism, can be used. The J-PAKE mechanism
has the following properties as described in [19]:
- off-line dictionary attack resistance it does not leak any
password verification information to a passive attacker
- forward secrecy it produces session keys that remain secure
even when the password is later disclosed
- known-key security it prevents a disclosed session key
from affecting the security of other sessions
- on-line dictionary attach resistance it limits an active
attacker to test only one password per protocol execution
One solution for using the Juggling scheme in the UEs
authentication to the network is to replace part of the AKA
protocol with the J-PAKE protocol.

Figure 6. Simplified J -PAKE usage in 4G authentication

This solution does not cover the first security issue present
in AKA, the identity protection. This aspect will be debated in
a separate article. This solution also assumes the existence of a
secure communication channel between the MME and the
HSS. Once the IMSI is sent to the HSS by the MME, the HSS
will return the shared key it has for this UE, secured via the
S6a interface. Having the password, the MME will run the J -
PAKE protocol with the UE, the eNB serving as simple relay
agent; the UE proves, via the J-PAKE rounds, its knowledge
of the password, and at this moment, the UE is considered
authenticated by the network and it has also authenticated the
network, This is a mutual authentication, resistant to the 4
security aspects listed above. It improves on the AKA
algorithm by providing forward secrecy for the keys resulted
from this negotiation. The generation of the EPS key hierarchy
is not impacted by the authentication mechanism, the
generation remains the same as described by the standard.
A more detailed comparison and simulation on the
effectiveness of the J -PAKE method versus the AKA method
is in progress.
J-PAKE is a password authentication keying agreement
protocol, a method to provide zero-knowledge proof using a
shared key that is never sent over the transmission medium.
One of the first algorithms of this type is the EKE (Encryption
Key Exchange) protocol, which has been proved to have many
33

flaws. SPEKE (Simple Password Exponential Key Exchange)
is one of the protocols that improved the EKE variant. SPEKE,
along with EKE and J -PAKE are all balanced versions of
password-authenticated key agreement. This variant uses the
same password to authenticate both peers. There is another
variant of PAKE, called augmented PAKE. This variant is
usable in a client/server environment. Here, a brute-force
attack on the connection is more inconvenient and the
representative protocols for this variant are B-SPEKE and SRP
(Secure Remote Password protocol). J-PAKE improves on the
limitations of S-PEKE, limitations that are already observed in
the BlackBerry implementation. The actual protocol level
security comparison between J -PAKE and SPEKE are
described in the J-PAKE presentation paper. The conclusions
are that EKE does not fulfill the off-line dictionary attack
resistance requirement, while the SPEKE does not fulfill the
on-line dictionary attack resistance requirement.

IV. CONCLUSIONS AND FUTURE WORK

This paper presented the basic 4G architecture and reviewed
the main security domains used to classify and integrate the
security aspects to this design. The paper focused on the
access-level security issues that may arise at the eNodeB, UE
and MME level. As the connection to the network poses the
most issues when talking about User Domain security, this
paper analyzed the authentication process of the UE
connecting to the 4G network. There are two most common
cases when talking about initial attach, the attach of a plain 4G
device and the attach of non-3GPP device.
The paper identified two issues that appear almost every
time: the lack of identity protection at the first initial attach
and the lack of perfect forward secrecy for the AKA
mechanism, inherited also in the EAP-AKA mechanism
specific to the authentication of the non-3GPP devices. At
least for the perfect forward secrecy issue, we have proposed
the usage of the J -PAKE protocol in the authentication
process, instead of the AKA protocol, which we consider a
flexible and lightweight mechanism, suited for use in the
mobile device environment.
The future articles will describe the comparison and a
possible simulation of the efficiency of J-PAKE in comparison
with SPEKE and other similar balanced PEKE algorithms, as
well as measure the efficiency of this protocol as the main
authentication algorithm in the 4G authentication process.
Further on, this study continues with the analysis of the
IMSI identity protection mechanism and proposes a solution
for the complete identity protection even for the first initial
attach process.

REFERENCES
[1] TS 23.401, GPRS Enhancements for E-UTRAN access,
http://www.3gpp.org/ftp/Specs/archive/23_series/23.401/23401-a10.zip
[retrieved: November 2010]
[2] TS 23.122, NAS Functions related to Mobile Stations in idle mode,
[3] TS 36.300, E-UTRAN Overall Description,
[4] TS 43.022, Functions of the MS in idle mode and group receive mode,
http://www.3gpp.org/ftp/Specs/archive/43_series/43.022/43022-920.zip
[5] TS 25.304, UE Procedures in idle mode and procedures for cell reselection
in connected mode,
[6] TS 33.401, SAE - Security Architecture,
[7] TS 33.310, Network Domain Security; Authentication Framework,
[8] TS 33.102, 3G Security Architecture,
[9] RFC 5516, Diameter Command Code Registration for the Third
Generation Partnership Project (3GPP) Evolved Packet System (EPS),
http://tools.ietf.org/html/rfc5516 , April 2009 [retrieved: November 2010]
[10] TS 29.272, MME related interfaces based on Diameter,
[11] Tech-Invite, http://tech-invite.com/, [retrieved: March 2010]
[12] TS 29.294, Tunneling Protocol for Control plane (GTPv2-C),
[13] TS 33.220, Generic Authentication Architecture; Generic Bootstrapping
Authentication,
[14] TR 33.919, Generic Authentication Architecture System Overview,
[15] TS 33.221, Support for Subscriber Certificates,
[16] Han-Cheng Hsiang and Weu-Kuan Shih, Efficient Remote Mutual
Authentication and Key Agreement with Perfect Forward Secrecy,
Information Technology J ournal 8, 2009, Asian Network for Scientific
Information [retrieved: November 2010]
[17] RFC 4187, EAP Method for 3GPP AKA,
http://tools.ietf.org/html/rfc4187 [retrieved: November 2010]
[18] RFC 2631, Diffie-Hellman Key Agreement Method,
http://tools.ietf.org/html/rfc2631 [retrieved: November 2010]
[19] F. Hao and P.Ryan, Password Authenticated Key Exchange by
J uggling, Proceedings of the 16th International Workshop on Security
Protocols,2008,
http://grouper.ieee.org/groups/1363/Research/contributions/hao-ryan-2008.pdf
[20]3GPP, http://3gpp.org/-partners-, [retrieved: November 2010]
[21] Georgios Kambourakis, Angelos Rouskas, and Stefanos Gritzalis,
"Performance Evaluation of Public Key-Based Authentication in Future
Mobile Communication Systems", August 2004, EURASIP J ournal on
Wireless Communications and Networking [retrieved: November 2010]
[22] Qiang Tang and Chris J . Mitchell, On the security of some password-
based key agreement schemes, 23rd May 2005 [retrieved: November 2010]
34

Security Analysis of LTE Access Network: Abstract: The Latest Technological Development in Mobile

Uploaded by

Copyright:

Available Formats

Security Analysis of LTE Access Network: Abstract: The Latest Technological Development in Mobile

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Security Analysis of LTE Access Network: Abstract: The Latest Technological Development in Mobile

Uploaded by

Copyright:

Available Formats

Security Analysis of LTE Access Network

Cristina-Elena Vintil, Victor-Valeriu Patriciu, Ion Bica

You might also like