Hybrid System Overview: Section 1
Hybrid System Overview: Section 1
Hybrid System Overview: Section 1
1-1
Section 1
The Toyota Hybrid System (THS) powertrain in the original Prius and the Toyota Hybrid System II (THSII) powertrain in the second generation Prius both provide impressive EPA fuel economy numbers and extremely clean emissions:
THS (20012003 Prius) City: Highway: 52 mpg 45 mpg THSII (2004 & Later) City: Highway: 60 mpg 51 mpg
SULEV
ATPZEV
SULEV standards are about 75% more stringent than ULEV and nearly 90% cleaner than LEV for smog forming exhaust gases. SULEV vehicles will emit less than a single pound of hydrocarbons during 100,000 miles of driving (about the same as spilling a pint of gasoline). ATPZEV vehicles use advanced technology capable of producing zero emissions during at least part of the vehicles drive cycle.
Figure 1.1
T072f101c
1-2
Figure 1.2
T071f102c
1-3
Section 1
IC Engine The 1NZFXE 1.5liter gasoline engine employs VVTi variable valve
timing and ETCSi electronic throttle control.
1NZ-FXE
Figure 1.3
T071f103p
1-4
Motor Generator 1 Motor Generator 1 (MG1) operates as the control element for the power (MG1) splitting planetary gear set. It recharges the HV battery and also
supplies electrical power to drive Motor Generator 2 (MG2). MG1 effectively controls the continuously variable transmission function of the transaxle and operates as the engine starter.
Figure 1.4
T071f104p
1-5
Section 1
Motor Generator 2 MG2 is used for motive force at low speeds and supplemental force at (MG2) high speeds. It provides power assist to the engine output as needed
and helps the vehicle achieve excellent dynamic performance. It also functions as a generator during regenerative braking.
Figure 1.5
T071f105p
1-6
Planetary Gear Unit The planetary gear unit is a power splitting device. MG1 is connected
to the sun gear, MG2 is connected to the ring gear and the engine output shaft is connected to the planetary carrier. These components are used to combine power delivery from the engine and MG2, and to recover energy to the HV battery.
Figure 1.6
T071f106p
1-7
Section 1
Inverter Current between MG1, MG2 and the HV battery is controlled by the
inverter. The inverter converts highvoltage battery DC to AC power, and it rectifies highvoltage AC from MG1 and MG2 to recharge the highvoltage battery.
Inverter Assembly
A device that converts the high-voltage DC (HV battery) into AC (MG1 and MG2) and vice versa.
Figure 1.7
T071f107p
1-8
HV Battery
Supplies electric power to MG2 during start-off, acceleration and uphill driving.
Figure 1.8
T071f108p
1-9
Section 1
When starting off and traveling at low speeds, MG2 provides the primary motive force. The engine may start immediately if the HV battery State of Charge (SOC) is low. As speed increases above 15 to 20 mph the engine will start. When driving under normal conditions, the engines energy is divided into two paths; a portion drives the wheels and a portion drives MG1 to produce electricity. The HV ECU controls the energy distribution ratio for maximum efficiency. During full acceleration, power generated by the engine and MG1 is supplemented by power from the HV battery. Engine torque combined with MG2 torque delivers the power required to accelerate the vehicle. During deceleration or braking, the wheels drive MG2. MG2 acts as a generator for regenerative power recovery. The recovered energy from braking is stored in the HV battery pack.
Hybrid Control The hybrid system uses various modes to achieve the most efficient Modes operation in response to the driving conditions. The following graphics
review each of these modes.
1-10
Stopped If the vehicle is fully charged and it not moving, the engine may stop.
The engine will start up automatically if the HV battery needs charging. Also, if MAX A/C is selected on a 2001 2003 Prius, the engine will run continuously due to the engine driven compressor. The 2004 & later Prius use an electric compressor.
Stopped
The engine may stop when the vehicle is not moving and the HV battery is fully charged.
Figure 1.9
T071f109c
1-11
Section 1
Starting Out When starting out under light load and light throttle, only MG2 turns
to provide power. The engine does not run and the vehicle runs on electric power only. MG1 rotates backwards and just idles; it does not generate electricity.
Starting Out
The electric power supply from the HV battery to MG2 provides force to drive the wheels.
Figure 1.10
T072f103c
1-12
Normal Driving During normal lowspeed driving (15 40mph), the engine runs and
provides power. MG2 turns and runs as a motor and provides an electric assist. MG1 is turned in the same direction by the engine as a generator and provides electricity for MG2.
Normal Driving
While the engine drives the wheels via the planetary gears, MG1 is driven via the planetary gears to supply electricity to MG2.
Figure 1.11
T072f104c
1-13
Section 1
Full Throttle For maximum acceleration or speed (over 100mph), electric drive Acceleration and power from MG2 supplements engine power. The HV battery provides High Speed Cruise electricity to MG2. MG1 also receives electrical power from the HV
battery and turns in the reverse direction to create an overdrive ratio for maximum speed.
Figure 1.12
T072f105c
1-14
Deceleration As soon as the driver releases the accelerator pedal, MG2 becomes a and Braking generator. MG2 is turned by the drive wheels and generates electricity
to recharge the HV battery. This process is called Regenerative Braking. As the vehicle decelerates, the engine stops running and MG1 turns backwards to maintain the gear ratio. When the brake pedal is depressed, most initial braking force comes from Regenerative Braking and the force required to turn MG2 as a generator. The hydraulic brakes provide more stopping power as the vehicle slows.
Figure 1.13
T072f106c
1-15
Section 1
Reverse When the vehicle moves in reverse, MG2 turns in reverse as an electric
motor. The engine does not run. MG1 turns in the forward direction and just idles; it does not generate electricity.
Reverse
MG2 rotates backwards to move the vehicle in reverse. The engine does not run.
Figure 1.14
T072f107c
1-16
Multi Display
A multi display is provided on the center cluster panel as standard equipment. The 7.0inch LCD screen has a pressure sensitive panel for easy function accessibility.
Energy Monitor
Figure 1.15
T071f115c
Figure 1.16
T071f116c
1-17
Section 1
In addition to the conventional mechanical key function and wireless door lock remote control function, this system provides a smart key with a bidirectional communication function. By enabling the smart ECU to recognize the presence of the smart key within the detection area, this system can lock or unlock the doors, or start the hybrid system without the use of the key, as long as the user has the smart key in their possession.
Door Open
Using smart entry by opening the door with smart key in pocket. The touch sensor is located on the back of the door handle.
Figure 1.17
T071f117c
1-18
On the 0103 Prius, an ignition key is used to operate the key cylinder (containing the ignition switch), in order to switch the power mode of the vehicle and start the system. On the 04 & later Prius, a push button start system operates the power switch by inserting a key in a key slot or by the driver keeping a key in their possession (models with smart entry and start system).
Power Mode A power mode (OFF, ACC, IGON, or READY) can be selected by
pressing the power switch. The indicator on this switch will tell you the power mode, which varies depending if the brake pedal is depressed or not while the switch is operated.
Figure 1.18
T071f118c
Figure 1.20
T071f120c
1-19
Section 1
Figure 1.19
T071f119c
Figure 1.21
T071f121c
1-20
Figure 1.22
T071f122c
Figure 1.23
T071f123c
Combination Meter
(04 & later Prius)
Figure 1.24
T071f124c
1-21
Section 1
1-22
Vehicle
Year/Prod. Date
Engine
Transmission
Worksheet Objectives
Review this sheet as you are doing the Hybrid System Overview worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
2. Unlike a conventional vehicle, the Prius may or may not start the engine when the vehicle is turned ON. What alerts the driver that the vehicle is ready to drive?
3. What is the primary motive force when starting, backing up or under light loads?
1-23
Section 1
4. While driving, what do you think happens when you shift into the B position?
5. When the vehicle is decelerating or braking, what kind of energy from the wheels is recovered and converted into electrical energy to recharge the HV Battery?
6. Where is the 12V auxiliary battery located and what is its function? Can the 12V battery be jump-started?
7. How can you tell if the vehicle has smart key and smart start?
8. Does the vehicle you are working on have navigation? Does it have Bluetooth? How can you tell?
2. When the vehicle begins to move forward after the release of the parking brake and brake pedal, what power source is being used to move the vehicle?
1-24
3. On a 2004 and later Prius, how do you start the vehicle (READY light ON) with the Power button? With and without smart key?
5. The engine may turn OFF periodically. List two conditions that will cause the engine to turn back ON.
Return all cars to the original state and return to the classroom.
1-25
Section 1
1-26
Name:
Date:
Self-assessment Objectives
Review this sheet as you are doing the Inclination Sensor Reset worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
I have questions
I know I can
Topic
Locate power button. Access the READY light. Use smart key & smart start. Locate the 12V battery. Locate the Navigation & Bluetooth functions.
Comment
1-27
Section 1
1-28
Section 2
Figure 2.1
T072f002c
2-1
Section 2
Figure 2.2
T071f202c
Hybrid Transaxle, consisting of MG1, MG2 and a Planetary Gear Unit Inverter Assembly containing an inverter, a boost converter, a DCDC converter, and an A/C inverter HV ECU, which gathers information from the sensors and sends calculated results to the ECM, inverter assembly, battery ECU and skid control ECU to control the hybrid system Shift Position Sensor Accelerator Pedal Position Sensor, which converts accelerator angle into an electrical signal Skid Control ECU that controls regenerative braking ECM HV Battery Battery ECU, which monitors the charging condition of the HV battery and controls cooling fan operation Service Plug, which shuts off the circuit The SMR (System Main Relay) that connects and disconnects the highvoltage power circuit Auxiliary Battery, which stores 12V DC for the vehicles control systems
2-2
Safety Procedures Incorrectly performed hybrid system repairs could cause electrical
shock, battery leakage or even an explosion. Be sure to perform the following safety procedures whenever servicing the hybrid vehicles highvoltage system or hybrid control system: Remove the key from the ignition. If the vehicle is equipped with smart key, turn the smart key system off. Disconnect the negative () terminal of the auxiliary battery. Wear insulated gloves. Remove service plug and put it in your pocket. Do not make any repairs for five minutes. If the key cannot be removed from the key slot (for instance, because of body damage during an accident) be sure to perform the following procedures: Disconnect the auxiliary battery. Remove the HEV fuse (20A yellow fuse in the engine compartment junction block.) When in doubt, pull all four fuses in the fuse block.
NOTE
Highvoltage insulated gloves can be ordered from the Toyota SPX/OTC SST catalog under part numbers: Small gloves 0000203100S Medium gloves 0000203200M Large gloves 0000203300L To check the integrity of the gloves surface, blow air into the glove and fold the base of the glove over to seal the air inside. Then, slowly roll the base of the glove towards the fingers. If the glove holds pressure, its insulating properties are intact. If there is an air leak, highvoltage electricity can find its way back through that same hole and into your body! Discard the glove(s) and start over until you have a pair of gloves that can fully protect you from the vehicles highvoltage circuits.
WARNING
After disabling the vehicle, power is maintained for 90 seconds in the SRS system and for five minutes in the highvoltage electrical system. If any of the disabling steps above cannot be performed, proceed with caution as there is no assurance that the highvoltage electrical system, SRS or fuel pumps are disabled. Never cut orange highvoltage power cables or open highvoltage components.
TOYOTA Hybrid System - Course 071
2-3
Section 2
WARNING
Due to circuit resistance, it takes at least five minutes before highvoltage is discharged from the inverter circuit. Even after five minutes have passed, the following safety precautions should be observed: Before touching an orange highvoltage cable, or any other cable that you cannot identify, use the tester to confirm that the voltage in the cable is 12V or less. After removing the service plug, cover the plug connector using rubber or vinyl tape. After removing a highvoltage cable, be sure to cover the terminal using rubber or vinyl tape. Use insulated tools when available. Do not leave tools or parts (bolts, nuts, etc.) inside the cabin. Do not wear metallic objects. (A metallic object may cause a shortcircuit.)
Submerged Many fire departments and police stations have been trained to safely Vehicle Safety remove hybrid vehicles from water in case of an emergency. Always call
your local fire department in this situation. To safely handle a Prius that is fully or partially submerged in water, disable the highvoltage electrical system and SRS airbags. Remove the vehicle from the water. Drain the water from the vehicle if possible. Then, follow the extrication and vehicle disable procedures below: Immobilize the vehicle. Chock the wheels and set the parking brake. Remove the key from the key slot. If equipped with smart key, use the smart cancel switch underneath the steering column to disable the system. Keep the electronic key at least 16 feet (5 meters) away from the vehicle. Disconnect the 12V auxiliary battery. Remove the HEV fuse in the engine compartment. When in doubt, pull all four fuses in the fuse block.
2-4
Service Plug
(01-03 Prius)
Figure 2.3
T071f203c
Service Plug
(04 & later Prius)
Figure 2.4
T071f204c
2-5
Section 2
Hybrid Transaxle
Figure 2.5
T071f205p
Transaxle Damper The transaxle damper uses a spring coil with low torsional
characteristics. In the 04 & later Prius, the spring rate characteristics of the coil spring have been reduced further to improve its vibration absorption performance and the shape of the flywheel has been optimized for weight reduction.
Transaxle Damper
The transaxle damper, which transmits the drive force of the engine to the transaxle, contains a torque fluctuation adsorption mechanism that uses a dry, single plate friction material.
Figure 2.6
T071f206p
2-6
04 Model Transaxle Type The No. of Ring Gear Teeth Planetary Gear Differential Gear Ratio Number of Links Chain Drive Sprocket Driven Sprocket Drive Gear Counter Gear Final Gear Fluid Capacity Driven Gear Drive Gear Driven Gear Liters (US qts qts, Imp qts) The No. of Pinion Gear Teeth The No. of Sun Gear Teeth P112 78 23 30 4.113 72 36 35 30 44 26 75 3 8 (4.0, 3.8 (4 0 3.3) 3 3)
Fluid Type Ty e
ATF WS or equivalent
MG1 & MG2 MG1 and MG2 function as both highly efficient alternating current Motor Generator 1 & synchronous generators and electric motors. MG1 and MG2 also serve Motor Generator 2 as sources of supplemental motive force that provide power assistance
to the engine as needed.
04 Model
Permanent Magnet Motor Generate, Engine Starter
03 Model
Function Maximum Voltage Cooling System MG2 Specifications Item Type Function Maximum Voltage Maximum Output Cooling System Figure 2.7 [V]
AC 500 Water-cooled
AC 273.6
04 Model
Permanent Magnet Motor Generate, Engine Starter
03 Model
[V]
kW (PS) / rpm
T071f207c
2-7
Section 2
MG1 Description MG1 recharges the HV battery and supplies electrical power to drive
MG2. In addition, by regulating the amount of electrical power generated (thus varying MG1s internal resistance and rpm), MG1 effectively controls the transaxles continuously variable transmission. MG1 also serves as the engine starter.
MG2 Description MG2 and the engine work together to drive the wheels. The addition of
MG2s strong torque characteristics help achieve excellent dynamic performance, including smooth startoff and acceleration. During regenerative braking, MG2 converts kinetic energy into electrical energy, which is then stored in the HV battery.
NOTE
Towing a damaged Prius with its front wheels on the ground may cause MG2 to generate electricity. If that happens, the electrical insulation could leak and cause a fire. Always tow the vehicle with the front wheels off of the ground or on a flat bed.
Planetary Gear Unit The planetary gear unit is used as a power splitting device. The sun
gear is connected to MG1, the ring gear is connected to MG2, and the planetary carrier is connected to the engine output shaft. The motive force is transmitted from the chain drive sprocket to the reduction unit via a silent chain.
Figure 2.8
T072f035
2-8
Reduction Unit The reduction unit consists of the silent chain, counter gears and final
gears. A silent chain with a small pitch width ensures quiet operation. The overall length has been reduced in contrast to the geardriven mechanism. The counter gear and final gear teeth have been processed through highprecision honing and their tooth flanks have been optimized to ensure extremely quiet operation.
Reduction Unit
The final gears have been optimized to reduce the distance between the engines center shaft and the differential shaft, resulting in a more compact transmission.
Figure 2.9
T071f209c
2-9
Section 2
Permanent When threephase alternating current is passed through the windings Magnet Motor of the stator coil, a rotating magnetic field is created. When the
rotation of this magnetic field is properly timed in relationship to the rotor, the magnetic field pulls the permanent magnets housed inside the rotor in a circle, causing the rotor to turn and creating the motors torque. The generated torque is proportionate to the amount of current passing through the stator coils and the rotational speed is controlled by the frequency of the threephase alternating current. A high level of torque can be generated efficiently at all speeds by properly controlling the rotating magnetic field and the angles of the rotor magnets. On the 04 & later Prius the builtin permanent magnets have been changed to a Vshaped structure to improve both power output and torque.
Figure 2.10
T071f210c
2-10
Figure 2.11
T071f211c
Speed Sensor This reliable and compact sensor precisely detects the magnetic pole (Resolver) position, which is essential for the control of MG1 and MG2.
The sensors stator contains three coils. Since the rotor is oval, the gap between the stator and the rotor varies with the rotation of the rotor. In addition, the HV ECU uses this sensor as an rpm sensor, calculating the amount of positional variance within a predetermined time interval.
Figure 2.12
T071f212
2-11
Section 2
Inverter Assembly
(04 & later Prius)
Figure 2.13
T071f213p
Inverter The inverter changes highvoltage direct current from the HV battery
into threephase alternating current for MG1 and MG2. The HV ECU controls the activation of the power transistors. In addition, the inverter transmits information that is needed to control current, such as the output amperage or voltage, to the HV ECU. The inverter, MG1, and MG2, are cooled by a dedicated radiator and coolant system that is separate from the engine coolant system. The HV ECU controls the electric water pump for this system. In the 04 & later Prius, the radiator has been simplified and the space it occupies has been optimized.
Boost Converter The boost converter boosts the nominal voltage of 201.6V DC that is (04 & later Prius) output by the HV battery to the maximum voltage of 500V DC. To boost
the voltage, the converter uses a boost IPM (Integrated Power Module) with a builtin IGBT (Insulated Gate Bipolar Transistor) for switching control, and a reactor to store the energy. When MG1 or MG2 acts as a generator, the inverter converts the alternating current (range of 201.6V to 500V) generated by either motor into direct current, then the boost converter drops the voltage to 201.6V DC to charge the HV battery.
2-12
Figure 2.14
T071f214c
Converter The vehicles auxiliary equipment (such as lights, audio system, A/C
cooling fan, ECUs, etc.) is powered by standard 12V DC. On the 0103 Prius, the THS generator voltage is 273.6V DC. A converter transforms the voltage from 273.6V DC to 12V DC to recharge the auxiliary battery. On the 04 and later Prius, the THSII generator outputs a nominal voltage of 201.6V DC. The converter transforms the voltage from 201.6V DC to 12V DC to recharge the auxiliary battery.
Figure 2.15
T071f215c
2-13
Section 2
A/C Inverter The inverter assembly includes a separate inverter for the air (04 & later Prius) conditioning system that changes the HV batterys nominal voltage of
201.6V DC into 201.6V AC to power the air conditioning systems electric inverter compressor.
A/C Inverter
(04 & later Prius)
Figure 2.16
T071f216c
2-14
Cooling System A dedicated cooling system uses a water pump to cool the inverter, for Inverter, MG1 MG1 and MG2. It is separate from the engine cooling system. This and MG2 cooling system activates when the power supply is switched to IG.
Cooling System
(04 & later Prius) The radiator for the cooling system is integrated with the radiator for the engine.
Figure 2.17
T071f217c
2-15
Section 2
Hybrid Nomograph
Ready-on.
Figure 2.18
T071f218c
2-16
Hybrid Nomograph
Starting out.
Figure 2.19
T071f219c
Hybrid Nomograph
Engine starting.
Figure 2.20
T071f220c
2-17
Section 2
Hybrid Nomograph
Light acceleration with engine.
Figure 2.21
T071f221c
Hybrid Nomograph
Low speed cruising.
Figure 2.22
T071f222c
2-18
Hybrid Nomograph
Full acceleration.
Figure 2.23
T071f223c
Hybrid Nomograph
High speed cruising.
Figure 2.24
T071f224c
2-19
Section 2
Hybrid Nomograph
Max speed.
Figure 2.25
T071f225c
Hybrid Nomograph
Deceleration or braking.
Figure 2.26
T071f226c
2-20
Hybrid Nomograph
Reverse.
Figure 2.27
T071f227c
Using Information Information Codes are a threedigit supplement to HV ECU DTCs. Codes They provide additional information and freeze frame data to help
diagnose the vehicles condition. These codes can be found on the Diagnostic Tester HV ECU menu. Use the screen flow shown below to access the codes. For a detailed description of each Information Code, refer to the DI section of the Repair Manual.
2-21
Section 2
Figure 2.28
T071f228
2-22
Vehicle
Year/Prod. Date
Engine
Transmission
Technician Objectives
This worksheet will familiarize you with the critical safety procedures involved in working with a high-voltage hybrid system. You will understand all safety procedures and use all safety equipment.
2. Using the Emergency Response Guide, explain how you could disable a hybrid vehicle if the ignition key or service plug were inaccessible?
2W1-1
Name:
Date:
Self-assessment Objectives
Review this sheet as you are doing the Hybrid Safety worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
I have questions
I know I can
Topic
Describe all safety procedures when working with the high voltages systems. Locate and list all safety equipment. Access the 12V battery. Access the high-voltage battery. Safely pull the service plug. Describe when the service plug needs to be removed.
Comment
2W1-3
Hybrid Safety
2W1-4
Vehicle
Year/Prod. Date
Engine
Transmission
Worksheet Objectives
In this worksheet you will use the Diagnostic Tester to obtain and view relevant information and observe data lists while driving the vehicle. You will then relate this information to the different components and technologies of the hybrid system.
Note: Remember that when REV and TORQ are the same (both + positive or both negative) the component is being used as a MOTOR. When REV and TORQ are different (ie. REV + & TORQ -) the component is a GENERATOR.
2W2-1
Hybrid Safety
3. Locate the Service Plug. Put on your safety gloves and protective eye wear and remove the plug. What device or devices are integrated into the service plug assembly?
4. Re-install the service plug and allow another student to remove the plug wearing their gloves. 5. When each student has removed and re-installed the plug, use the Repair Manual, EWD, or TIS workstation to locate the IGCT Relay or HEV fuse in the vehicle. Write the location of the relay below.
2W1-2
4. From a stop, lightly accelerate to 20 mph. Record the following values: MG1 REV MG2 REV ENGINE SPD MG1 TORQ MG2 TORQ -
8. Bring vehicle speed up to approximately 35 mph. Record the following values: MG1 REV MG2 REV ENGINE SPD MG1 TORQ MG2 TORQ -
12. Bring vehicle speed up to approximately 45 mph. Record the following values: MG1 REV MG2 REV ENGINE SPD MG1 TORQ MG2 TORQ -
2W2-2
V2
2W2-3
10. Accelerate full throttle to approx 45 mph. How is the temperature changing?
Charge
2W2-4
Name:
Date:
Self-assessment Objectives
Review this sheet as you are doing the Data List Information worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
I have questions
I know I can
Topic
Create User Data from the HV ECU Data List. Determine if MG1 is being used as a motor or generator. Determine if MG2 is being used as a motor or generator. View the Battery ECU Data List. Determine the SOC (State of Charge).
Comment
2W2-5
2W2-6
Section 3
High-Voltage Battery
Overview
The sealed nickelmetal hydride (NiMH) battery technology developed for the hybrid system provides both high power density and excellent longevity. The hybrid system controls charge and discharge rates to keep the HV battery at a constant State of Charge (SOC).
HV Battery Layout
The HV Battery, Battery ECU and SMR (System Main Relay) are enclosed in a single case located in the luggage compartment behind the rear seat.
Figure 3.1
T071f301c
3-1
Section 3
Power Cable The power cable is a highvoltage, highamperage cable that connects
the HV battery with the inverter and the inverter with MG1 and MG2. In the 04 & later Prius, the power cable also connects the inverter with the A/C compressor. The power cable is routed under the rear seat, through the floor panel, along the underthefloor reinforcement, and connects to the inverter in the engine compartment. The 12V DC wiring harness follows a similar route from the auxiliary battery to the front of the vehicle The power cable is shielded to reduce electromagnetic interference. For identification purposes, the highvoltage wiring harness and connectors are colorcoded orange to distinguish them from ordinary lowvoltage wiring.
Figure 3.2
T071f302c
3-2
High-Voltage Battery
HV - Nickel-Metal The HV battery pack contains six nickelmetal hydride 1.2V cells that Hydride Battery are connected in series to form one module.
In the 0103 Prius, 38 modules are divided into two holders and connected in series. Thus, the HV battery contains a total of 228 cells and has a rated voltage of 273.6V. In the 04 and later Prius, 28 modules are connected for a rated voltage of 201.6V. The cells are connected in two places to reduce the internal resistance of the battery. The electrode plates in the HV battery are made of porous nickel and metal hydride alloy.
NOTE
For battery recycling information, please refer to the Warranty Policy and Procedure manual.
HV Battery Pack Battery pack voltage Number of Ni-MH battery modules in the pack Number of cells Ni-MH battery module voltage
Figure 3.3
T071f303c
3-3
Section 3
Battery ECU
The battery ECU provides the following functions: It estimates the charging/discharging amperage and outputs charge and discharge requests to the HV ECU so that the SOC can be constantly maintained at a center level. It estimates the amount of heat generated during charging and discharging, and adjusts the cooling fan to maintain HV battery temperature. It monitors the temperature and voltage of the battery and if a malfunction is detected, can restrict or stop charging and discharging to protect the HV battery.
Battery ECU
(04 & later Prius)
Figure 3.4
T071f304p
3-4
High-Voltage Battery
State Of Charge The battery ECU constantly monitors HV battery temperature, voltage (SOC) and amperage. It also checks for leaks in the HV battery.
While the vehicle is in motion, the HV battery undergoes repetitive charge/discharge cycles as it becomes discharged by MG2 during acceleration, and charged by the regenerative brake during deceleration. The Battery ECU estimates the charge/discharge amperage and outputs charge/discharge requests to the HV ECU to maintain the SOC at a median level. The target SOC is 60%. When the SOC drops below the target range, the battery ECU informs the HV ECU. The HV ECU then signals the engine ECM to increase power to charge the HV battery. If the SOC is below 20%, the engine is not producing power.
Delta SOC The normal, low to high SOC deviation is 20%. If the Delta SOC
exceeds 20%, this means that the HV battery ECU cannot correct or maintain the SOC difference within the acceptable range.
SOC
The battery ECU outputs requests to the HV ECU so the SOC can be maintained at a center level.
Figure 3.5
T071f305c
3-5
Section 3
System Main Relay The System Main Relay (SMR) connects and disconnects power to the (SMR) highvoltage circuit based on commands from the HV ECU. A total of
three relays (one for the negative side and two for the positive side) are provided to ensure proper operation. When the circuit is energized, SMR1 and SMR3 are turned ON. The resistor in line with SMR1 protects the circuit from excessive initial current (called inrush current). Next, SMR2 is turned ON and SMR1 is turned OFF, allowing current to flow freely in the circuit. When deenergized, SMR2 and SMR3 are turned OFF in that order and the HV ECU verifies that the respective relays have been properly turned OFF.
Figure 3.6
T072f040c
3-6
High-Voltage Battery
Service Plug When the service plug is removed the highvoltage circuit is shut OFF
at the intermediate position of the HV battery. The service plug assembly contains a safety interlock reed switch. Lifting the clip on the service plug opens the reed switch, shutting OFF the SMR. The main fuse for the highvoltage circuit is inside the service plug assembly.
NOTE
For safety reasons, you must always turn the vehicle OFF before removing the service plug.
HV Battery Cooling The battery ECU detects battery temperature via three temperature System sensors in the HV battery and one intake air temperature sensor.
Based on those readings, the battery ECU adjusts the duty cycle of the cooling fan to maintain the temperature of the HV battery within the specified range. The battery ECU keeps the fan OFF or running at LO if: The A/C is being used to cool the vehicle. Some margin is left in the temperature of the battery.
Figure 3.9
T071f309p
3-7
Section 3
Figure 3.10
T071f310c
Auxiliary Battery The Prius uses an Absorbed Glass Mat (AGM) 12V maintenance free
auxiliary battery. This 12V battery powers the vehicles electrical system similar to a conventional vehicle. The battery is grounded to the metal chassis of the vehicle and vented to ambient (outside) air with a tube. This battery is very sensitive to highvoltage. When charging the auxiliary battery you should use the Toyota approved charger, because a standard battery charger does not have the proper voltage control and may damage the battery. If the approved charger is not available you may use a trickle charger if the amperage is kept below 3.5 A. The battery should be removed from the vehicle during charging. However, it is safe to jumpstart the Prius from either the battery or the jumpstart terminal under the hood. This will allow the vehicles charging system to restore the battery to normal SOC. If the vehicle will not be used for more than two weeks, disconnect the 12V battery to prevent it from discharging. Always make sure that all doors are properly closed and that the interior lights are OFF, especially overnight. These situations will quickly deplete the 12V battery.
3-8
High-Voltage Battery
Auxiliary Battery
In glass mat batteries, the electrolyte is trapped in separators to reduce the amount of hydrogen gas released when the battery is charged. Glass mat batteries are sealed and the electrolyte cannot be replaced.
Figure 3.11
T071f311c
Figure 3.12
T071f312p
3-9
Section 3
3-10
High-Voltage Battery
Vehicle
Year/Prod. Date
Engine
Transmission
Worksheet Objectives
In this worksheet you will diagnose hybrid malfunctions by viewing DTCs, Information Codes, and the HV ECU Data List.
2. Connect the Diagnostic Tester to DLC3. Select Codes All to check all the ECUs. 3. How many systems are checked when using Codes All?
5. Now view the Information Codes by pressing enter on the systems that say NG, then press enter again. Highlight the number next to INFORMATION and press enter.
3-11
Section 3
6. Use the Repair Manual or TIS to look up the DTC and Information Code in order to find what part of the system is affected. List this information below.
7. Is there any information in the HV ECU Data List that can help you diagnose the vehicle? If so, print and highlight the information. 8. After diagnosing the vehicle, clear the codes and return to the classroom.
Hint: To clear DTCs, you must exit out of CODES ALL and enter each section individually.
3-12
Name:
Date:
Self-assessment Objectives
Review this sheet as you are doing the Hybrid DTC Diagnosis worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
I have questions
I know I can
Topic
Locate vehicle warning lights. View Codes All using the Diagnostic Tester. View the Information Codes. Use TIS & Repair Manual to research these codes. View the HV ECU Data List. Clear Codes.
Comment
3-13
Section 3
3-14
Section 4
Engine
Overview
The 1NZFXE is one of two power sources for the Prius. The 1NZFXE is a 1.5 liter inline 4cylinder engine with VVTi (Variable Valve Timing with intelligence) and ETCSi (Electric Throttle Control System with intelligence). The 1NZFXE includes a number of modifications that help balance performance, fuel economy and clean emissions in hybrid vehicles. One unique aspect of the 1NZFXE is its Atkinson cycle valve timing, which allows the engine to decrease emissions by varying the relationship between the compression stroke and the expansion stroke. Another feature incorporated on 04 & later models is a special coolant heat storage system that recovers hot coolant from the engine and stores it in an insulated tank where it stays hot for up to three days. Later, an electric pump precirculates the hot coolant through the engine to reduce HC emissions normally associated with a cold start.
Engine
The 1NZ-FXE is a 1.5 liter inline 4-cylinder engine.
Figure 4.1
T071f401p
4-1
Section 4
Engine Specifications
Model Engine Type No. of Cyls. & Arrangement Valve Mechanism Combustion Chamber Manifolds Fuel System Displacement Bore x Stroke Compression Ratio Max Output Max Torque Intake Valve Timing Exhaust Firing Order Research Octane Number Octane Rating Engine Service Mass * (Reference) Oil Grade Tailpipe Emission Regulation Evaporative Emission Regulation kg (lb) (SAENET) (SAENET) Open Close Open Close cm3 (cu. in.)
04 Prius 1NZFXE 4Cylinder, Inline 16Valve DOHC, Chain Drive (with VVTi) Pentroof Type CrossFlow SFI 1497 (91.3) 75.0 x 84.7 (2.95 x 3.33) 13.0 : 1 57 kw @ 5000 rpm (76 HP @ 5000 rpm) 111 Nm @ 4200 rpm (82 ft1bf @ 4200 rpm) 18 ~ 15 BTDC 72 ~ 105 ABDC 34 BBDC 2 ATDC 1342 91 or higher 87 or higher 86.1 (189.8) API SJ, SL, EC or ILSAC SULEV ATPZEV, ORVR
03 Prius 52 kw @ 4500 rpm (70 HP @ 4500 rpm) 18 ~ 25 BTDC 72 ~ 115 ABDC 86.6 (190.9) API SH, SJ, EC or ILSAC LEVII, ORVR
mm (in.)
*: Weight shows the figure with the oil and engine coolant fully filled.
Figure 4.2
T071f402
4-2
Engine
VVT-i and VVTi allows the engine control system to independently adjust intake Atkinson Cycle valve timing. The 1NZFXE uses this ability to move between
conventional valve timing and Atkinson cycle valve timing, varying the effective displacement of the engine. In an Atkinson cycle engine, the intake valve is held open well into the compression stroke. While the valve is open, some of the cylinder volume is forced back into the intake manifold. This creates an effective reduction in engine displacement. By using the VVTi system to continuously adjust intake valve timing between Atkinson cycle valve timing and conventional valve timing, the engine can maximize fuel efficiency whenever possible while still producing maximum power when required.
Valve Timing
The maximum retard closing timing of the intake valve by the VVT-i system has been decreased from 115 degrees ABDC (After Bottom-Dead-Center) in the 01-03 Prius to 105 degrees ABDC in the 04 & later Prius.
Figure 4.4
T071f404c
4-3
Section 4
Intake Manifold
The intake manifold has a large surge tank that accommodates the air forced back into the manifold during the compression stroke of the Atkinson cycle engine.
Figure 4.5
T071f405p
Intake Manifold Because some of the air is forced back into the intake manifold during
the compression stroke of the Atkinson cycle, the 1NZFXEs intake manifold includes a large surge tank to accommodate the extra volume. Also, the length of the intake manifolds intake pipe has been shortened to improve air efficiency and the intake pipes have been integrated midstream to reduce weight. Finally, the throttle body has been positioned down flow in the center of the surge tank to achieve uniform intake air distribution.
4-4
Engine
Engine Control System Sensors Mass Airflow Meter The Mass Airflow Meter determines the amount of air flowing into the
intake manifold. To measure airflow, a heated platinum wire is positioned in the intake air stream just above the throttle body. The temperature of the hot wire is maintained at a constant value by controlling the current flow through the hot wire. Incoming air tends to cool the hot wire. As airflow increases, current flow through the wire must be increased to maintain the hot wires set temperature. This current flow is then measured and reported to the ECM as the output voltage of the airflow meter.
Intake Air The Intake Air Temperature Sensor is built into the Mass Airflow Temperature Sensor Meter and uses an NTC (Negative Temperature Coefficient) thermistor
to monitor intake air temperature. As intake air temperature increases, the thermistors resistance and the signal voltage to the ECM decrease.
Engine Coolant The Engine Coolant Temperature Sensor is located in the engine block Temperature Sensor and uses an NTC thermistor monitor engine coolant temperature. As
coolant temperature increases, the thermistors resistance and the signal voltage to the ECM decrease.
Accelerator Pedal The Accelerator Pedal Position Sensor is mounted on the accelerator Position Sensor pedal assembly. Two Hall ICs are used to detect accelerator pedal
position. Due to the characteristics of the Hall ICs, different signals are output depending on whether the pedal is being pressed or released. The HV ECU receives the signals and compares them to ensure that there is no malfunction.
Throttle Position The Throttle Position Sensor is mounted on the throttle body and Sensor converts throttle valve angle into two voltage signals (VTA and VTA2).
The ECM compares the two voltages to ensure there is not malfunction. The ECM uses this information to calculate throttle valve opening, then actuates the throttle control motor to adjust throttle valve position accordingly.
Idle Speed Control ETCSi adjusts the throttle valve angle to control idle speed. No
separate idle speed control system is required. The system includes idleup control during cold engine operation, intake air volume control to improve engine startability, and load compensation for changes such as when the A/C is turned ON or OFF.
TOYOTA Hybrid System - Course 071
4-5
Section 4
Knock Sensor The Knock Sensor is mounted on the cylinder block and detects
detonation or knocking in the engine. The sensor contains a piezoelectric element that generates a voltage when cylinder block vibrations due to knocking deform the sensor. If engine knocking occurs, ignition timing is retarded until the knock is suppressed.
Crankshaft Position The Crankshaft Position Sensor (NE signal) consists of a toothed signal Sensor plate mounted on the crankshaft and an inductive pick up coil. The
signal plate has 34 teeth, with one gap created by missing teeth, so the sensor generates a 34pulse waveform for every crankshaft revolution. Since this is an inductive sensor, both the frequency and amplitude of the generated signal increase with increasing engine rpm. The ECM uses the NE signal to determine engine rpm and detect misfires.
Camshaft Position The Camshaft Position Sensor (G2 signal) consists of a signal plate Sensor with a single tooth that is mounted on the exhaust camshaft and a pick
up coil. The sensor generates onepulse waveform for every revolution of the exhaust camshaft. Since this is an inductive sensor, both the frequency and amplitude of the generated signal increase as engine rpm increases. The ECM uses the G2 signal to determine the position of the number one piston for the ignition firing order.
Air/Fuel Ratio On the 04 and later Prius, the Bank 1 Sensor 1 O2 sensor is replaced Sensor by an A/F sensor. The A/F sensor detects the air/fuel ratio over a wider
range, allowing the ECM to further reduce emissions. The Prius uses a planar (flat) A/F sensor. The sensor and heater on a planar sensor are narrower than those on a conventional cup sensor. This allows the heater to heat the alumina and zirconia more quickly, accelerating sensor activation.
4-6
Engine
Exhaust System
Figure 4.6
T071f406c
HC Adsorber and The HCAC system adsorbs and retains unburned hydrocarbons (HC) Catalyst System produced by the engine during and following a cold start. Once the (HCAC) engine has warmed up, the hydrocarbons are released and purged
(01-03 Prius)
through the warm threeway catalyst. This improves exhaust emissions at low temperatures.
4-7
Section 4
Figure 4.7
T072f207c
HCAC - Purge
When the TWC reaches operating temperature the VSV closes and the bypass valve opens. Stored HC is now purged and flows through the TWC where it is oxidized.
Figure 4.8
T072f208c
Figure 4.9
T072f209c
4-8
Engine
Cooling System
The coolant heat storage tank on the 04 & later Prius can store hot coolant up to three days. This allows for quick engine warm up and reduces emissions.
Figure 4.10
T071f410c
Figure 4.11
T071f411c
4-9
Section 4
Coolant Heat Starting with the 04 Prius, the cooling system includes a Coolant Heat Storage Storage Tank that can store hot coolant at 176 degrees Fahrenheit for
up to three days. When starting a cold engine, the system uses an auxiliary water pump to force the hot coolant into the engine. This preheating of the engine reduces HC exhaust emissions.
Figure 4.12
T072f203c
4-10
Engine
Figure 4.13
T072f204p
Figure 4.14
T072f205p
SERVICE TIP
When servicing the coolant system on the 04 & later Prius: Disconnect the coolant heat storage water pump connector to prevent circulation of the coolant and prevent possible injury. Drain the engine coolant. When refilling, operate the coolant heat storage water pump to help the inflow of coolant into the tank.
TOYOTA Hybrid System - Course 071
4-11
Section 4
Figure 4.15
T072f206c
Figure 4.16
T071f416c
4-12
Engine
Figure 4.17
T071f417c
Figure 4.18
T071f418c
4-13
Section 4
Figure 4.19
T071f419c
Bladder Fuel Tank The bladder fuel tank reduces the amount of fuel lost to evaporation. To
prevent evaporation the fuel is stored inside a flexible resin storage tank sealed within a metal outer tank. The resin tank expands and contracts with the volume of the fuel, so the space into which fuel can evaporate is minimized. This approach dramatically reduces evaporative emissions.
Fuel Bladder
The resin bladder in the Prius fuel tank expands and contracts with the changing quantity of fuel.
Figure 4.20
T071f420p
4-14
Engine
Fuel Gauge The direct acting fuel gauge is located in the sealed inner tank. This
gauge consists of a pipe surrounded by a coil. A magnet attached to a float in the pipe moves up and down with changes in fuel level causing a change in the coils magnetic field. This results in a slight difference in potential at either end of the coil that is read by the Meter ECU.
NOTE
The fuel pump is integrated with the fuel tank and cannot be serviced separately.
Figure 4.21
T071f421p
4-15
Section 4
Inclination Sensors There are two inclination sensors located in the meter ECU that detect
vehicle longitudinal and latitudinal inclination to correct the fuel level calculation. Corrections are made based on the signals from the inclination sensors and the ambient temperature sensor located in the fuel tank. The inclinometer must be reset if the driver can only pump a few gallons of gas into his/her tank, or the vehicle runs out of gas with three or four bars left on the fuel meter. The inclinometer must also be reset if the Prius is refilled on an excessive slope or if the fuel gauge becomes inaccurate. Please refer to the Prius Repair Manual for the inclinometer calibration procedure.
Figure 4.22
T072f302c
NOTE
Unlike conventional vehicles, on a hybrid vehicle the engine may start many times in a single drive cycle. This increases potential hot soak" issues.
4-16
Engine
NOTE
Overfilling (trying to force additional fuel into the tank) pushes excess fuel into the EVAP system. This may cause EVAP DTCs and may even require the replacement of some EVAP system components.
Energy Monitor The Energy Monitor, which includes a historical bar graph and total
trip fuel economy (MPG), is very accurate. Multiple, comparative calculations are performed by several computers. Fuel usage and fuel economy are calculated by monitoring fuel injector duration and operating frequency. The ECU compares these values with miles traveled to calculate miles per gallon. The battery ECU closely monitors energy consumption in Watts. By calculating the amount of energy spent, recovered, and stored, the computer can calculate the required fuel burn. Fuel required to create this amount of energy is compared against the engine ECU fuel injection calculation to insure accuracy. Driving pattern, speed, and load characteristics are stored in the HV ECU as Historical Data." Historical Data is used to further refine the MPG calculation. This data takes about three to six weeks to accumulate if the battery is disconnected or the HV ECU is replaced.
Fuel Type & Use only 87 Octane unleaded gasoline in the Prius. The Prius has a Octane Rating smaller fuel tank opening to help prevent nozzle mixups. At a
minimum, the gasoline used should meet the specifications of ASTM D4814 in the United States. Do not use premium gasoline. It may causes starting problems with the Prius. There is no gas mileage benefit when using premium gas!
4-17
Section 4
EVAP To check for leaks in the EVAP system the Prius introduces purge System Checks vacuum into the entire system, then looks for changes in pressure. Any
loss of vacuum indicates a leak in the system. To detect EVAP leaks from the vapor reducing fuel tank, the Prius uses the density method. This method uses an O2 sensor to measure HC density in the exhaust gases. Added HC from a leak will cause a reduction in exhaust oxygen content.
Figure 4.23
T072f020c
4-18
Engine
EVAP Components The EVAP system includes the following main components:
Canister Closed Valve VSV This normally open valve is located between the fresh air line and the fuel tank. This Vacuum Switching Valve (VSV) stops airflow into the EVAP system to seal the system and enable leak detection. It is also known as the CAN CTRL VSV or the CCV VSV. Purge Flow Switching Valve VSV Allows vacuum from the EVAP VSV (or Purge VSV) to flow through the canister. When activated by the ECM during internal fuel bladder leak detection, it switches airflow from the canister to the outer tank bladder only. This VSV is also called the Tank Bypass VSV on the Diagnostic Tester. EVAP (Alone) VSV Is used to control engine vacuum to the EVAP system in order to remove stored hydrocarbons from the charcoal canister. It is also used for system leak detection and may be referred to as the Purge VSV. Vapor Pressure Sensor (VPS) The ECU provides a 5V signal and ground to the Vapor Pressure Sensor. The VPS sends a voltage signal back to the ECU, which varies between 0.1 4.9V in response to tank pressure. Fuel Cutoff Valve Causes the filler nozzle to shut off when the fuel tank is full to prevent overfilling. Refuel Check Valve Antisiphon valve that prevents fuel from entering EVAP system lines. Also called Tank Over Fill Check Valve.
NOTE
The following VSVs are referred to by several different names in some Toyota repair information: CAN CTRL VSV Canister Closed Valve or CCV VSV Tank Bypass VSV Purge Flow Switching Valve EVAP VSV (Alone) Purge VSV Refuel Check Valve Tank Over Fill Check Valve
4-19
Section 4
Figure 4.24
T071f424c
4-20
Engine
Operation - ORVR When refueling, the engine is OFF and EVAP VSV is CLOSED (OFF). Refueling The resin bladder expands as fuel enters, so there is virtually no vapor
space above the fuel. Hydrocarbon (HC) vapor flows from the secondary tank and fuel pump through the EVAP line to the charcoal canister where the HC is absorbed and stored. Airflows from the charcoal canister to the airspace between the metal outer tank and bladder and to the Canister Closed Valve. The Canister Closed Valve (CCV) is OPEN, allowing air to exit from the Fresh Air Valve. The Refuel Check Valve and Fuel Cutoff Valve work together to prevent overfilling and liquid fuel from entering the charcoal canister.
ORVR Refueling
Figure 4.25
T072f028c
4-21
Section 4
Purging During normal purge operation the engine is running and the ECM
duty cycles the EVAP VSV ON and OFF allowing vacuum from the intake manifold to pull air through the EVAP system. The Purge Flow Switching Valve is OFF, opening the connection between the charcoal canister and the EVAP VSV. HC vapor flows from the charcoal canister to the EVAP VSV and into the intake manifold. The Canister Closed Valve (CCV) is OPEN, allowing fresh air to enter from the air cleaner and flow through the airspace between the metal outer tank and bladder and up to the charcoal canister. As this air passes through the canister, it purges the HC.
Purging
Figure 4.26
T071f426c
4-22
Vehicle
Year/Prod. Date
Engine
Transmission
Worksheet Objectives
This worksheet will give you additional experience diagnosing hybrid system diagnostic codes and identifying a common Out of Gas condition.
NOTE: DO NOT operate the vehicle with a SOC (State of Charge) below 35%!!! Reinstall the Circuit Opening Relay and cycle the key to recharge the battery. Do not leave the parking lot area!!
5. Using the Repair Manual, locate the Circuit Opening Relay. Leave the engine running and remove the Circuit Opening Relay to shut OFF the fuel pump. What happened to the engine?
4W1-1
6. After the circuit-opening relay is removed, turn the ignition OFF and attempt to restart the vehicle. Describe what happens.
7. Drive under normal acceleration and observe the SOC. What is the SOC doing as the temperature increases?
9. Approximately how long can you operate the vehicle only on the HV Battery?
10. Exit out of the Data List and enter back into OBD/MOBD. Select CODES ALL. 11. On the Diagnostic Tester, highlight each system with a NG and press enter to retrieve the codes. Record the DTCs and the related system below:
CODES
SYSTEM
4W1-2
12. After the codes are recorded, clear all the codes by entering each area individually. 13. Re-install the circuit opening relay and cycle the ignition key OFF and back to the READY position to re-start engine. 14. Using TIS, look up the TSB regarding Maintenance for HV and Aux. Batteries at Port and Dealers. Once you are have opened the TSB, search for Onboard Equalizing Charge of HV Battery. Follow the instructions and begin the battery equalization process to re-charge the HV battery. NOTE: This procedure is only for the 01-03 Prius. Notify the instructor when you are finished.
4W1-3
4W1-4
Name:
Date:
Self-assessment Objectives
Review this sheet as you are doing the Out of Gas Condition worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
I have questions
I know I can
Topic
Create User Data from the Battery ECU Data List. Locate and remove the circuit-opening relay. Determine the SOC. Record DTCs.
Comment
4W1-5
4W1-6
Vehicle
Year/Prod. Date
Engine
Transmission
Worksheet Objectives
In this worksheet you will reset the Inclination Sensor. This procedure can be useful in solving a customer concern about improper fuel reading.
4. On the 01-03 Prius: Depress and hold the Trip button while turning the ignition key to the ON position. Release and press the Trip button three more times within five seconds: Release-Press-Release-Press-Release-Press and Hold.
4W2-1
Continue holding the Trip button for at least five seconds, then release. Check that the inclination sensor information is displayed in the dash.
(*) Current result display mode 0: Input state 1: Input state complete 2: E2ROM error 3: Speed input during input state or cancel during ODO input state Front rear direction sensor info. (*1) Sensor Area code A/D value for A/D value (*2)
Note: This procedure may take several attempts. Each time you start again, remove the key from the ignition and wait at least five seconds. 5. List the six-digit number displayed.
6. What do the first three digits mean? What do the last three digits mean?
7. After recording the six-digit number, lean on the front or rear bumper. Are the numbers changing?
8. Release the bumper and allow the vehicle to return to normal ride height. 9. When you pressed and held the Trip button for at least five seconds at the end of the procedure a single number should have appeared. What number was displayed?
10. According to the repair manual, what does this number mean?
4W2-2
Result Display Mode 0: Under processing 1: Recording completed 2: EEPROM error 3: Speed input or cancel during setting
If the number one (1) appeared, you are finished and the sensor is now reset. This allows for proper fuel and gas mileage reading.
4W2-3
4W2-4
Name:
Date:
Self-assessment Objectives
Review this sheet as you are doing the Inclination Sensor Reset worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
I have questions
I know I can
Topic
Locate Inclination Sensor information from TIS or Repair Manual. Determine what the reading means in relation to the vehicle.
Comment
4W2-5
4W2-6
Section 5
Chassis
Overview
Toyota hybrid vehicles use a number of specialized chassis systems including: A shiftbywire system with electronic transmission control. A regenerative braking system that recovers much of the energy normally lost to heat and friction during braking. An Electric Power Steering (EPS) system that improves fuel economy because it only consumes energy when it is in use.
Shift Control The 0103 Prius uses a shiftbywire system. The shift position sensor (01-03 Prius) is connected to a columnmounted shift lever and outputs two voltage
signals: a main signal and a sub signal. Both contain information about shift position. The HV ECU determines shift position when both signals match.
Shift Control The 04 & later Prius uses a different shiftbywire system. It uses two (04 & later Prius) sensors to monitor shift lever movement: a Select Sensor that detects
the lateral movement and a Shift Sensor that detects the longitudinal movement. The combination of these signals is used to determine shift position. When shift selection is complete, the reactive force of a spring returns the lever to its home position.
Shift Control
(01-03 Prius)
Figure 5.1
T071f501c
5-1
Section 5
Shift Lock
(01-03 Prius)
Figure 5.2
T071f502c
Shift Assembly
(04 & later Prius)
Figure 5.3
T072f107c
Shift Control The 04 & later Prius uses an electronic Shift Control Actuator to Actuator engage the parking pawl. When the Shift Control Actuator receives a (04 & later Prius) lock signal from the transmission ECU it rotates, which moves the
parking lock rod and forces the parking lock pawl to engage the parking gear. The Shift Control Actuator detects its own position when the battery is reconnected, so it does not require initialization.
5-2
Chassis
Figure 5.4
T072f406c
SERVICE TIP
If there is a malfunction in the shift control actuator, the vehicle will not go into park. The Master Warning Light will illuminate, the shift position indicators on the dash will flash, and the Park button light will flash. In this case, the vehicle cannot be turned OFF unless the parking brake is applied. Then the vehicle can be turned OFF but cannot be turned back ON again.
Cycloid Reduction The Shift Control Actuator includes a cycloid gear reduction Mechanism mechanism that increases the actuators torque, ensuring that the (04 & later Prius) parking lock will release when the vehicle is parked on a slope.
This mechanism consists of an eccentric plate mounted on the motors output shaft, a 61tooth fixed gear that is secured to the motor housing and a 60tooth driven gear. As the output shaft rotates, the eccentric plate presses the driven gear against the fixed gear. The driven gear, which has one tooth less than the fixed gear, rotates one tooth for every complete rotation of the eccentric plate. The result is a gear reduction ratio of 61:1, along with an equivalent increase in torque.
5-3
Section 5
Figure 5.5
T071f505c
SERVICE TIP
The Diagnostic Tester cannot turn off the shift control system. To power down the system remove the 30amp main fuse located on the left side of the fuse box on the drivers side of the engine compartment. This may be necessary if the vehicle needs to be pushed out of the shop.
Fuse Location
Removing the 30A PCON MTR fuse disables the shift control system.
Figure 5.6
T071f506c
5-4
Chassis
Brake System The hybrid vehicle brake system includes both hydraulic brakes and a
unique regenerative braking system that uses the vehicles momentum to recharge the HV battery. As soon as the accelerator pedal is released, the HV ECU initiates regenerative braking. MG2 is turned by the wheels and used as a generator to recharge the HV battery. During this phase of braking, the hydraulic brakes are not used. When more rapid deceleration is required, the hydraulic brakes are activated to provide additional stopping power. To increase energy efficiency the system uses the regenerative brakes whenever possible. Selecting B" on the shift lever will maximize regenerative efficiency and is useful for controlling speeds downhill. In B mode, about 30% of the energy is recovered. If either the regenerative or hydraulic braking system fails, the remaining system will still work. However, the brake pedal will be harder to press and the stopping distance will be longer. In this situation, the brake system warning light will illuminate.
NOTE
The battery will accept charge up to an instantaneous rate of 20 to 21 KWH. Much of the energy from light braking at high speeds and harder braking at lower speeds can be recovered. Excess energy over the charging limits is wasted as heat in the brakes. At this time there is no way for the driver to know the limit of regenerative energy recovery.
Figure 5.7
T071f507c
5-5
Section 5
Figure 5.8
T071f508c
Hydraulic Brake The 0103 Prius applies hydraulic pressure from the master cylinder Booster directly to the front brakes. For the rear brakes, it uses a hydraulic (01-03 Prius) brake booster to increase brake force. Within the hydraulic brake
booster, a pump draws brake fluid from the reservoir tank and forces it into the accumulator under high pressure. The accumulator stores the highpressure fluid until it is needed. To make sure system pressure stays at the right level, two pressure switches monitor hydraulic pressure coming from the accumulator: Pressure Switch PH controls pump activation. Pressure Switch PL generates a warning when system pressure is too low. If one of the pressure switches malfunctions it can cause the pump to operate continuously, creating excessive pressure in the system. If that happens, a relief valve shunts brake fluid to the reservoir tank to relieve the excess pressure. If the brake booster fails, the Brake System Warning Light and Buzzer will illuminate. Pressing the brake pedal repeatedly may turn ON the Brake System Warning Light and Buzzer briefly. If the brake booster is operating normally, the light and buzzer will turn OFF after a few seconds after start up.
5-6
Chassis
Brake Actuator In the 04 & later Prius, the conventional brake booster has been (04 & later Prius) replaced by a hydraulic power source that is controlled by the Skid
Control ECU. The hydraulic power source uses many of the same components used on the previous system, including a pump, pump motor, accumulator, relief valve, 2 motor relays, and an accumulator pressure sensor. To improve the system, the accumulator has been made more gastight, and a plungertype pump has been adopted. The control portion of the brake actuator includes: 2 master cylinder solenoid valves 4 pressure appliance valves 4 pressure reduction valves 2 master cylinder pressure sensors 4 wheel cylinder pressure sensors
Brake ECU In the 0103 Prius, the Brake ECU controls the following brake (01-03 Prius) functions:
Conventional brake control ABS with EBD control Regenerative brake cooperative control The Brake ECU exchanges sensor information with the HV ECU.
5-7
Section 5
Figure 5.9
T071f509c
Skid Control ECU In the 04 & later Prius, brake control processing is moved to the Skid (04 & later Prius) Control ECU, which handles:
Conventional brake control ABS with EBD control Brake Assist Enhanced VSC Regenerative brake cooperative control The Skid Control ECU exchanges sensor information EPS ECU and the HV ECU.
5-8
Chassis
Figure 5.10
T071f510c
Brake Pedal The 04 & later Prius uses an Electronically Controlled Brake (ECB) Stroke Sensor system. To determine the amount of brake force requested, the Brake (04 & later Prius) Pedal Stroke Sensor uses a variable resistor to detect the amount of
brake pedal movement, and then transmits that information to the Skid Control ECU.
SERVICE TIP
When installing a Brake Pedal Stroke Sensor: Initially, the sensor lever is locked into the 0" stroke position by a small pin. Do not detach the pin until the installation has been completed. Install the sensor. Then, firmly press the brake pedal once to break off the pin. Make sure the broken pin does not remain in the sensor lever.
5-9
Section 5
Figure 5.11
T071f511c
Stroke Simulator During regenerative braking fluid flow to the front calipers is limited.
To retain a normal pedal stroke during regenerative braking, the Stroke Simulator consumes some of the fluid flow from the master cylinder so that the pedal can move normally. The stroke simulator is located between the master cylinder and the brake actuator. It uses two coil springs with different spring constants to provide pedal stroke characteristics in two stages.
Stroke Simulator
Figure 5.12
T072f112c
5-10
Chassis
Power Source In the 04 & later Prius a Power Source Backup Unit has been added so Backup Unit that the ECB will function long enough to stop the vehicle even if the (04 & later Prius) 12V battery is compromised. The unit contains 28 capacitor cells that
store an electrical charge provided by the vehicles 12V power supply. The capacitor cells discharge when the power switch is turned OFF. If the Power Source Backup Unit is removed, it must first be checked for residual voltage.
Figure 5.13
T072f605c
5-11
Section 5
Regenerative Brake Regenerative brake cooperative control balances the brake force of the Cooperative Control regenerative and hydraulic brakes to minimize the amount of kinetic
energy lost to heat and friction. It recovers the energy by converting it into electrical energy. On the 04 & later Prius, the increased power output of MG2 provides increased regenerative brake force. In addition, the distribution of the brake force has been improved through the adoption of the ECB system, effectively increasing the range of the regenerative brake. These attributes enhance the systems ability to recover electrical energy which contributes to fuel economy.
Figure 5.14
T072f047c
5-12
Chassis
Electronic Brake Distribution (EBD) Control (04 & later Prius) Brake Force Distribution Front/Rear (04 & later Prius)
In the 04 & later Prius, brake force distribution (which was performed mechanically in the past) is now performed under electrical control of the skid control ECU. The skid control ECU precisely controls the braking force in accordance with the vehicles driving conditions. Generally, when the brakes are applied the vehicles weight shifts forward, reducing the load on the rear wheels. When the Skid Control ECU senses this condition (based on speed sensor output) it signals the brake actuator to regulate rear brake force so that the vehicle will remain under control during the stop. The amount of brake force applied to the rear wheels varies based the amount of deceleration. The amount of brake force that is applied to the rear wheels also varies based on whether or not the vehicle is carrying a load.
Figure 5.15
T072f511c
When the brakes are applied while the vehicle is cornering, the load applied to the inner wheel decreases while the load applied to the outer wheel increases. When the Skid Control ECU senses this condition (based on speed sensor output) it signals the brake actuator to regulate brake force between the left and right wheels to prevent a skid.
5-13
Section 5
Brake Assist System In emergencies, drivers often panic and do not apply sufficient pressure (04 & later Prius) to the brake pedal. So on the 04 & later Prius, the Brake Assist system
interprets a quick push of the brake pedal as emergency braking and supplements braking power accordingly. To determine the need for an emergency stop, the Skid Control ECU looks at the speed and the amount of brake pedal application based on signals from the master cylinder pressure sensors and the brake pedal stroke sensor. If the Skid Control ECU determines that the driver is attempting an emergency stop it signals the brake actuator to increase hydraulic pressure. A key feature of the Brake Assist system is that the timing and the degree of braking assistance are designed to ensure that the driver does not discern anything unusual about the braking operation. As soon as the driver eases up on the brake pedal, the system reduces the amount of assistance it provides.
Brake Assist
Figure 5.16
T072f512c
5-14
Chassis
Enhanced VSC The Enhanced VSC system available on the 04 & later Prius helps System maintain stability when the vehicles tires exceed their lateral grip. (04 & later Prius) The system helps control the vehicle by adjusting the motive force and
the brakes at each wheel when: The front wheels lose traction but the rear wheels dont. (front wheel skid tendency known as understeer) The rear wheels lose traction but the front wheels dont. (rear wheel skid tendency, or oversteer) When the Skid Control ECU determines that the vehicle is in understeer or oversteer, it decreases engine output and applies the brakes to the appropriate wheels individually to control the vehicle. When the skid control ECU senses understeer, it brakes the front and rear inside wheel. This slows the vehicle, shifts the load to the outside front wheel and limits front wheel skid. When the skid control ECU senses oversteer, it brakes the front and rear outside wheel. This restrains the skid and moves the vehicle back toward its intended path.
Cooperative Control Enhanced VSC provides the appropriate amount of steering assist with EPS based on driving conditions by coordinating EPS and VSC control. (04 & later Prius)
Figure 5.17
T072f111c
5-15
Section 5
A 12V motor powers the EPS system so that steering feel is not affected when the engine shuts off. The EPS ECU uses torque sensor output along with information from the Skid Control ECU about vehicle speed and torque assist demand to determine the direction and force of the power assist. It then actuates the DC motor accordingly.
Figure 5.18
T072f114c
EPS ECU The EPS ECU uses signals from the torque sensor to interpret the
divers steering intentions. It combines this information with data from other sensors regarding current vehicle conditions to determine the amount of steering assist that will be required. It can then control the current to the DC motor that provides steering assist current to the DC motor that provides steering assist.
5-16
Chassis
Figure 5.19
T072f049c
Power Steering When the steering wheel is turned, torque is transmitted to the pinion System causing the input shaft to rotate. The torsion bar that links the input
shaft and the pinion twists until the torque and the reaction force equalize. The torque sensor detects the twist of the torsion bar and generates an electrical signal that is proportional to the amount of torque applied to the torsion bar. The EPS ECU uses that signal to calculate the amount of power assist the DC motor should provide. The 0103 Prius torque sensor is a surfacecontact resistor and the 04 & later Prius uses an inductiontype torque sensor.
DC Motor The DC motor uses a worm gear to transmit the motors torque to the
column shaft.
Torque Sensor
(01-03 Prius)
Figure 5.20
T071f520p
5-17
Section 5
Torque Sensor
(04 & later Prius) Detection Ring 1 and 2 are mounted on the input shaft and Detection Ring 3 is mounted on the output shaft. When torque is applied to the torsion bar the detection rings move in relationship to each other. The detection coil senses a change in inductance that is proportional to the amount of torque applied.
Figure 5.21
T072f049c
Reduction For 01 to 03, the reduction mechanism transmits power assist from Mechanism the motor to the pinion shaft. The reduction mechanism consists of a (01-03 Prius) pinion gear integrated with the motor shaft and a ring gear that is
secured to the pinion shaft.
Reduction For 04 & later, the reduction mechanism transmits power assist from Mechanism the motor to the column shaft. The reduction mechanism consists of a (04 & later Prius) worm gear integrated with the motor shaft and wheel gear that is
connected to the column shaft.
5-18
Chassis
Fail Safe If the EPS ECU detects a malfunction in the EPS system, a warning
light illuminates to alert the driver. The EPS ECU will store the DTC(s) and the system will power down, however the system still provides the ability to steer manually.
DC Motor
Figure 5.22
T071f522p
5-19
Section 5
5-20
Section 6
Body Electrical
Overview
The body electrical system includes special technology to increase fuel efficiency and accommodate the special requirements of a hybrid powertrain. For instance, the 2004 & later Prius uses an electric compressor so that A/C operation is not dependent on the engine. It also uses a humidity sensor to make cabin dehumidification more efficient. To maintain communication between the vehicles many electronic control components, hybrid vehicles use three types of multiplex communication: CAN, BEAN and AVCLAN. A Gateway ECU is used to link the three circuits.
Air Conditioning The Prius A/C unit provides 2way flow so it can recirculate warm System internal air in the foot well while simultaneously introducing fresh, dry
external air to the upper part of the cabin. This allows it to effectively heat the vehicle and demist the windshield at the same time. The 0103 Prius air conditioning is controlled from the air conditioning control panel. The 04 & later Prius air conditioning system can be controlled either from the air conditioning screen on the multi display or from switches on the steering pad. The system includes several components to meet the special requirements of a hybrid vehicle. The 04 & later Prius includes an electric compressor that is powered by the inverter and does not draw any power unless it is needed to run the A/C. The hybrid vehicle A/C system also uses two Positive Temperature Coefficient (PTC) heaters embedded in the heater core to supplement the heat provided by the engine. The A/C control circuits include special logic tailored to support the hybrid powertrain. If the HV battery becomes too warm with recirculation ON, the HV battery ECU will switch to FRESH in order to increase the flow of air across the battery.
6-1
Section 6
Figure 6.1
T071f601c
6-2
Body Electrical
Heater Core and The hybrid vehicles gasoline engine is small, thermally efficient, and PTC Heater runs only when needed. Therefore, engine coolant may not always be
hot enough to heat the cabin to a comfortable temperature. To address this, two 165Watt PTC heater elements are embedded in the heater core and used to supplement engine heat when warming the vehicle.
Heater Core
Figure 6.2
T071f602
PTC Heater
Figure 6.3
T071f603
6-3
Section 6
Condenser and The Prius A/C condenser includes a subcooler that improves heat Sub-Cool Cycle exchange efficiency. After the refrigerant passes through the
condensing portion of the condenser, both the liquid refrigerant and any gaseous refrigerant that was not liquefied during condensation are cooled again in the supercooling portion of the condenser. Because of this twostep approach the refrigerant sent to the evaporator is almost completely liquefied.
NOTE
When recharging most cooling systems, air bubbles disappear from the refrigerant when the system is full. With this system, however, air bubbles will disappear from the refrigerant before the system is full. See the Prius Repair Manual for the proper method of recharging this system.
Sub-Cool Cycle
Figure 6.4
T072f052c
Compressor The 0103 Prius uses a scroll compressor with an oil separator that (01-03 Prius) reduces the circulation of compressor oil in the system. NOTE
When diagnosing the A/C, you may need to force the A/C system to remain on. Setting the controls to the MAX A/C position will cause the engine to remain on, maintaining A/C compressor operation.
6-4
Body Electrical
A/C Compressor
Selecting MAX A/C on the 01-03 Prius will cause the engine to run continuously
Figure 6.5
T071f605p
Electric Compressor The 04 & later Prius uses an electric compressor driven by an (04 & later Prius) integrated motor. The motor runs on 201.6V AC supplied by the A/C
inverter so compressor operation does not depend on the engine. The electric compressor consists of a spirally wound fixed scroll and variable scroll, a brushless motor, and an oil separator. The oil separator reclaims most of the compressor oil that is intermixed with the refrigerant. To insure proper insulation between the compressor housing and the highvoltage components inside the compressor, the 04 Prius uses a special high insulation value ND11 compressor oil. NEVER use any compressor oil other than ND11.
NOTE
The A/C compressor is powered by 201.6V AC. So when servicing the A/C compressor you should use the same high voltage safety procedures you would use for the vehicles other high voltage circuits.
Figure 6.6
T071f606p
6-5
Section 6
Room Temperature Sensor and Humidity Sensor (04 & later Prius)
The room temperature sensor includes a humidity sensor to help make the A/C systems dehumidification process more effective. As a result, compressor power consumption has been reduced while still maintaining a comfortable humidity level within the cabin. The humiditysensing resistance film contains small carbon particles. As humidity in the cabin changes the hydroscopic film expands and contracts, changing the distance between the carbon particles. This changes the resistance of the film and sensor output voltage.
Humidity Sensor
(04 & later Prius)
Figure 6.7
T071f607c
6-6
Body Electrical
Water Pump The electric water pump provides stable heater performance even when
the engine is stopped. When the engine is running the engines water pump is forcing coolant through the system so the electric water pump does not operate. On the 0103 Prius, when the engines water pump is operating a bypass valve opens to minimize flow resistance. The bypass valve has been discontinued on the 04 & later Prius because a new pump design minimizes water flow resistance.
Figure 6.8
T072f053c
6-7
Section 6
Multiplex The Prius uses the following communication systems to coordinate Communication vehicle activities: System
The Controller Area Network (CAN) links vehicle control systems that require highspeed communication, such as the ECM, HV ECU, Skid Control ECU and others. The Body Electronics Area Network (BEAN) connects the body control systems. The Audio Visual Communication Local Area Network (AVCLAN) links the audiovisual system ECUs and devices.
The Gateway ECU contains communication circuits that allow the CAN, BEAN and AVCLAN systems to connect with each other.
Multiplex Communication
(04 & later Prius)
Figure 6.9
T071f609c
6-8
Body Electrical
Figure 6.10
T071f610c
Control Protocol Communication Speed Communication Wire Drive Type Data Length
Figure 6.11
Chassis Electrical System Control CAN (ISO Standard) 500 k bps (Max. 1 M bps) Twisted-pair Wire Differential Voltage Drive 1-8 Byte (Variable)
Body Electrical System Control BEAN (TOYOTA Original) Max. 10 k bps AV Single Wire Single Wire Voltage Drive 1-11 Byte (Variable) AVC-LAN (TOYOTA Original) Max. 17.8 k bps Twisted-pair Wire Differential Voltage Drive 0-32 Byte (Variable)
T071f611
6-9
Section 6
The ATPZEV 2004 & later Prius, the warranty offers: Basic 3 years / 36,000 miles Powertrain (Engine, Transaxle with motors) 5 years / 60,000 miles Hybrid System 8 years / 100,000 miles Emission Performance, Emission Defects, and Hybrid Battery Pack 150,000 miles
6-10
Body Electrical
Vehicle
Year/Prod. Date
Engine
Transmission
Worksheet Objectives
This worksheet will familiarize you with the operation of the high voltage A/C compressor on the 2004 and later Prius using Active Tests and viewing the high and low pressures. You will also become familiar with the customize modes on the Diagnostic Tester, which allow A/C functions to be modified to suit customer needs.
2. What type of compressor oil is used and why is it unique to this system?
3. List the safety precautions that should be followed when servicing the A/C System.
6-11
Section 6
6-12
Body Electrical
3. What happens to the humidity sensor reading when the A/C is turned ON?
4. What happens to the compressor target speed when the humidity sensor and evaporator temperature sensor values drop?
Note: Return all cars to the original state and return to the classroom.
6-13
Section 6
6-14
Name:
Date:
Self-assessment Objectives
Review this sheet as you are doing the Electric Air Conditioning worksheet. Check off either category after completing the worksheet and instructor presentation. Ask the instructor if you have questions. The Comments section is for you to write notes on where to find the information, questions, etc.
I have questions
I know I can
Topic
Describe the electric A/C compressor. Describe the safety precautions of why ND11 oil must be used. List the safety precautions to be followed when servicing the A/C system. Access Active Test and select compressor speed. Locate the humidity sensor using TIS or the repair manual. View the A/C Data List. Locate and use Customize Mode for A/C.
Comment
6-15
Section 6
6-16
Appendix A
Acronym Meaning
A/C A/F A/T ABS AC ACC ALT AT - PZEV AUX AVC-LAN AVG B BA BATT BEAN CAN CB CCV CO CO2 COMB. CV D DC DEF DLC3 DOHC DTC DVOM EBD ECM ECU ENG EPA EPS ERG ETCS-i EVAP FE FL GND Air Conditioning Air/Fuel Ratio Automatic Transmission (Transaxle) Anti-lock Brake System Alternating Current Accessory Alternator Advanced Technology - Partial Zero Emissions Vehicle Auxiliary Audio Visual Communication - Local Area Network Average Regenerative Engine Braking Brake Assist Battery Body Electronic Area Network Controller Area Network Circuit Breaker Canister Closed Valve Carbon Monoxide Carbon Dioxide Combination Control Valve Drive Direct Current Defogger Data Link Connector 3 Double Over Head Cam Diagnostic Tester Code Digital Volt/Ohm Meter Electronic Brake Distribution Engine Control Module Electronic Control Unit Engine Environmental Protection Agency Electric Power Steering Emergency Response Guide Electronic Throttle Control System w/ intelligence Evaporative Emission Fuel Economy Fusible Link Ground
TOYOTA Hybrid System - Course 071 p1
Acronym List
of 3
Acronym Meaning
GPS HC HCAC H-Fuse HV IAC IC IG INT LED LEV LLC MAF MAX MG1 MG2 MIL MIN N No. O2 OEM ORVR P PCS PS PTC R RAM RBS RLY SEN SFI SLLC SMR SOC SRS SST SULEV SW TAS THS Global Positioning Sensor Hydrocarbons Hydrocarbon Absorption Catalyst High Current Fuse High Voltage Idle Air Control Integrated Circuit Ignition Instrument Panel Light Emitting Diode Low Emissions Vehicle Long Life Coolant Mass Air Flow Maximum Motor Generator 1 Motor Generator 2 Malfunction Indicator Lamp Minimum Neutral Number Oxygen Original Equipment Manufacturing On-board Recovery Park Power Control System Power Steering Positive Temperature Coefficient Reverse Random Access Memory Regenerative Brake System Relay Sensor Sequential Multiport Fuel Injection Super Long Life Coolant System Main Relay State of Charge Supplemental Restraint System Special Service Tool Super Ultra Low Emissions Vehicle Switch Technical Assistant System Toyota Hybrid System
p2
Appendix A
of 3
Acronym Meaning
TIS TPS TRAC TWC ULEV V VENT VIM VIN VPS VSC VSV VVT-i WOT ZEV Toyota Information System Throttle Position Sensor Traction Control System Three Way Catalytic Converter Ultra Low Emissions Vehicle Volts Ventilator Vehicle Interface Module Vehicle Identification Number Vapor Pressure Sensor Vehicle Stability Control Vacuum Switching Valve Variable Valve Timing with Intelligence Wide Open Throttle Zero Emissions Vehicle
Appendix A
p3
of 3
Appendix B
DO NOT DO
DO NOT leave the key in the ON position with the vehicle OFF for an extended period of time. (The 12-Volt auxiliary battery will quickly discharge.) DO turn the key OFF or leave the vehicle running (READY light ON) to avoid discharge of the 12-Volt battery. DO NOT leave the auxiliary battery connected to the vehicle if it will be sitting for over three weeks. DO NOT charge the auxiliary battery with a regular battery charger. DO disconnect the auxiliary battery if the vehicle will be sitting for over three weeks. DO pulse charge the auxiliary battery with Toyotas charger. (It must be recharged at a rate of no more than 3.5A or damage will occur.) DO tow the Prius on a flat bed or with the front wheels off the ground. DO NOT tow the Prius with all four wheels on the ground. (Will create electricity.) DO NOT physically push the Prius around in the shop. (May create electricity.) DO NOT shift into neutral with the READY light ON and let the vehicle sit. (High voltage battery cannot recharge in neutral.) DO NOT pull the service plug without wearing high-voltage insulated gloves. DO drive or move the vehicle on rollers when in the shop. DO keep the vehicle in park. DO wear high-voltage insulated gloves whenever working near high-voltage systems. DO NOT change the oil until you have confirmed that the key is OFF. DO turn the key OFF before an oil change. (Dont be fooled. You may not hear the engine running even though the car is ON! The engine will turn back ON!) DO NOT get out of the car until you have confirmed it is in Park. DO put the vehicle in Park before getting out. (Dont be fooled. You may not hear the engine running even though the car is ON! The car will drive away!) DO NOT run the vehicle out of GAS! (The HV battery may have to be recharged at a dealership.) DO turn the vehicle OFF immediately if you run out of gas. Once the vehicle has been refueled, the engine may be able to recharge the HV battery.
TOYOTA Hybrid System - Course 071 p1
of 1
Appendix C
Note:
DO NOT drain coolant using the bolt on the bottom of the transaxle or tamper with the bleeder plug directly in front of the inverter assy, for a normal cooling system service. Use only Toyota SLLC. This coolant is pre-mixed - DO NOT add water!
of 1
Appendix D
CAUTION: HIGH VOLTAGE. DO NOT TOUCH DURING OPERATION. CAUTION: HIGH VOLTAGE. DO NOT TOUCH DURING OPERATION.
Person in charge:
p1
Person in charge:
of 1