331

12.1. CLASSIFICATION OF LOADS

A load may be defined as the combined effect of external forces acting on a body. The loads
may be classified as : (i) dead loads, (ii) live or fluctuating loads, (iii) inertia loads or forces and
(iv) centrifugal loads or forces.
The other way of classification is (i) tensile loads, (ii) compressive loads, (iii) torsional or
twisting loads, (iv) bending loads and (v) shearing loads.
The load may be a point (or concentrated) or distributed.
Point load. A point load or concentrated load is one which is considered to act at a point. In
actual practical, the load has to be distributed over a small area, because, such small knife-edge
contacts are generally neither possible, nor desirable.
Distributed load. A distributed load is one which is distributed or spread in some manner
over the length of the beam. If the spread is uniform, (i.e., at the uniform rate, say w kN or N/metre
run) it is said to be uniformly distributed load and is abbreviated as u.d.l. If the spread is not at
uniform rate, it is said to be non-uniformly distributed load. Triangulary and trapezoidally distributed
loads fall under this category.
12.2. STRESS
When a body is acted upon by some load or external force, it undergoes deformation (i.e.,
change in shape or dimensions) which increases gradually. During deformation, the material of the
body resists the tendency of the load to deform the body and when the load influence is taken over by
the internal resistance of the material of the body, it becomes stable. This internal resistance which
the body offers to meet with the load is called stress.
Stress can be considered either as total stress or unit stress. Total stress represents the total
resistance to an external effect and is expressed in N, kN or MN. Unit stress represents the resistance
developed by a unit area of cross-section and is expressed in kN/m
2
or MN/m
2
or N/mm
2
. For the
remainder of this text, the word stress will be used to signify unit stress.
12
Simple Stresses and Strains
12.1. Classification of loads. 12.2. Stress. 12.3. Simple stress. 12.4. StrainTensile strain
Compressive strainShear strainVolumetric strain. 12.5. Hookes Law. 12.6. Mechanical
Properties of metals 12.7. Tensile test. 12.8. Strain hardening (or work hardening). 12.9. Poissons
ratio. 12.10. Relations between the elastic moduliiRelation between E and CRelation between
E and K. 12.11. Stresses induced in compound ties or struts. 12.12. Thermal stresses and strains
HighlightsObjective Type QuestionsTheoretical QuestionsUnsolved Examples.
332 APPLIED MECHANICS
The various types of stresses may be classified as :
1. Simple or direct stress
(i) Tension (ii) Compression (iii) Shear.
2. Indirect stress
(i) Bending (ii) Torsion.
3. Combined stress. Any possible combination of types 1 and 2.
This chapter deals with simple stresses only.
12.3. SIMPLE STRESS
Simple stress is often called direct stress because it develops under direct loading conditions.
That is, simple tension and simple compression occurs when the applied force, called load is in line
with the axis of the member (axial loading) (Figs. 12.1 and 12.2) and simple shear occurs, when equal,
parallel and opposite forces tend to cause a surface to slide relative to the adjacent surface (Fig. 12.3).
W W
Fig. 12.1. Tensile stress
W W
Fig. 12.2. Compressive stress
W
W
( ) Rivet resisting shear a
W
W
( ) Rivet failure due to shear b
Fig. 12.3
In certain loading situations, the stresses that develop are not simple stresses. For example,
referring to Fig. 12.4, the member is subjected to a load which is perpendicular to the axis of the
member (transverse loadings) (Fig. 12.5). This will cause the member to bend, resulting in deformation
of the material and stresses being developed internally to resist the deformation. All three types of
stressestension, compression and shear will develop, but they will not be simple stresses, since
they were not caused by direct loading.
Plate
Punch
Die
Slug
( ) Punch approaching plate a ( ) Punch shearing plate b ( ) Slug showing sheared area c
Die
Fig. 12.4
SIMPLE STRESSES AND STRAINS 333
W
Simply supported beam
(Transverse loading)
Fig. 12.5
When any type of simple stress develops, we can calculate the magnitude of the stress by,
f =
W
A
...(12.1)
where f = stress, N/cm
2
or kgf/cm
2
W = load
external force causing
stress to develop
L
N
M
O
Q
P
, N or kgf
A = area over which stress develops, cm
2
.
It may be noted that in cases of either simple tension or simple compression, the areas which
resist the load are perpendicular to the direction of forces. When a member is subjected to simple
shear, the resisting area is parallel to the direction of the force. Common situations causing shear
stresses are shown in Figs. 12.3 and 12.4.
12.4. STRAIN
Any element in a material subjected to stress is said to be strained. The strain (e) is the
deformation produced by stress. The various types of strains are explained below :
12.4.1. Tensile Strain
A piece of material, with uniform cross-section, subject to a uniform axial tensile stress, will
increase its length from l to (l + l) (Fig. 12.6) and the increment of length l is the actual deformation
of the material. The fractional deformation or the tensile strain is given by
e
t
=
l
l
...(12.2)
dl l
W W
Fig. 12.6
12.4.2. Compressive Strain
Under compressive forces, a similar piece of material would be reduced in length (Fig. 12.7)
from l to (l l).
dl
l
W W
Fig. 12.7
The fractional deformation again gives the strain e,
where e =
l
l
...(12.2 a)
334 APPLIED MECHANICS
12.4.3. Shear Strain
In case of a shearing load, a shear strain will be produced which is measured by the angle
through which the body distorts.
In Fig. 12.8 is shown a rectangular block LMNP fixed at one face and subjected to force F.
After application of force, it distorts through an angle and occupies new position LMNP. The
shear strain (e
s
) is given by
e
s
=
NN
NP

= tan = (radians) ...... (since is very small)

The above result has been obtained by assuming NN equal to arc (as NN is very small)
drawn with centre P and radius PN.
F
M N N
f
f
L P
M
Fig. 12.8
12.4.4. Volumetric Strain
It is defined as the ratio between change in volume and original volume of the body, and is
denoted by e
v
.
e
v
=
Change in volume
Original volume
=
V
V
...(12.3)
The strains which disappear with the removal of load are termed as elastic strains and the
body which regains its original position on the removal of force is called an elastic body. The body is
said to be plastic if the strains exist even after the removal of external force. There is always a limiting
value of load upto which the strain totally disappears on the removal of load, the stress corresponding
to this load is called elastic limit.
12.5. HOOKES LAW
Robert Hooke discovered experimentally that within elastic limit, stress varies directly as
strain
Stress Strain
i.e., or
Stress
Strain
= a constant
This constant is termed as Modulus of Elasticity.
(i) Youngs modulus. It is the ratio between tensile stress and tensile strain or compressive
stress and compressive strain. It is denoted by E. It is the same as modulus of elasticity
or E =
f
e
...(12.4)
(ii) Modulus of rigidity. It is defined as the ratio of shear stress to shear strain and is denoted
by C, N or G. It is also called shear modulus of elasticity.
or
f
e
s
s
= C, N or G ...(12.5)
SIMPLE STRESSES AND STRAINS 335
(iii) Bulk or volume modulus of elasticity. It may be defined as the ratio of normal stress
(on each face of a solid cube) to volumetric strain and is denoted by the letter k.
or
f
e
n
v
= K ...(12.6)
12.6. MECHANICAL PROPERTIES OF METALS
Some important mechanical properties of metals are discussed below :
1. Strength. The strength of a metal is its ability to withstand various forces to which it is
subjected during a test or in service. It is usually defined as tensile strength, compressive strength,
proof stress, shear strength, etc. Strength of materials is general expression for the measure of capacity
of resistance possessed by solid masses or pieces of various kinds to any causes tending to produce in
them a permanent and disabling change of form or positive fracture. Materials of all kinds owe their
strength to the action of the forces residing in and about the molecules of the bodies (the molecular
forces) but mainly to that ones of these known as cohesion; certain modified results of cohesion as
toughness or tenacity, hardness, stiffness and elasticity are also important elements and strength is
in relation of the toughness and stiffness combined.
2. Elasticity. A material is said to be perfectly elastic if the whole strains produced by a load
disappears completely on the removal of the load. The modulus of elasticity or Youngs modulus (E)
is the proportionally constant between stress and strain for eastic materials. Youngs modulus is
indicative of the property elastic materials. Youngs modulus is indicative of the property called
stiffness ; small values of E indicate flexible materials and large value of E reflects stiffness and
rigidity. The property of spring back is a function of modulus of elasticity and refers to the extent to
which metal springs back when an elastic deforming load is removed. In metal cutting, modulus of
elasticity of the work-piece affects its rigidity, and modulus of elasticity of the cutting tools and tool-
holder affect their rigidity.
3. Plasticity. Plasticity is the property that enables the formation of a permanent deformation
in a material. It is the reverse of elasticity: a plastic material will retain exactly the shape it takes
under load, even after the load is removed. Gold and lead are highly plastic materials. Plasticity is
made use of in stamping images on coins and ornamental works.
During plastic deformation there is the displacement of atoms within the metallic grains and
consequently the shapes of metallic components change.
It is because of this property that certain synthetic materials are given the name plastics.
These materials can be changed into required shape easily.
4. Ductility. It is the ability of a metal to withstand elongation or bending. Due to this property,
wires are made by drawing out through a hole. The material shows a considerable amount of plasticity
during the ductile extension. This is a valuable property in chains, ropes etc., because they do not
snap off, while in service, without giving sufficient warning by elongation.
Note. The elongation of a test piece of metal which occurs when it is subjected to a sufficiently high
tensile stress is a measure of the ductility of the material. The elongation is measured accurately by an
extensometer etc. The value of this test as a measure of ductility has often been questioned however. The actual
property measured is the ability of the metal to distort or flow without breaking, this is the same as ductility,
but there is no universal agreement regarding the value of the test to the engineer. For sheet strip and wire
material, a bend test used as a substitute for elongation test. A simple bend test consists of bending the material
through 180; the radius of the bend depending on the gauge and composition of the material under test. The
sample must withstand this test without cracking. If the reverse-bend test as its name suggests the test piece is
bent through 90 and then back again; if necessary, this reversal is repeated a specified number of times, or
until the sample breaks. This test is considerably more searching than the elongation test and reveals defects
which the elongation test may not show up. For tube material, a bend test is carried out on a test strip cut from
the wall of the tube while a length of the tube itself is usually flattened between two plates until its internal
walls are a specified distance apart.
336 APPLIED MECHANICS
5. Malleability. This is the property by virtue of which a material may be hammered or rolled
into thin sheets without rupture. This property generally increases with the increase of temperature.
The common metals in order of their ductility and malleability (at room temperature) are
given below:
Ductility Malleability
Gold Gold
Silver Silver
Platinum Copper
Iron Aluminium
Nickel Tin
Copper Platinum
Aluminium Lead
Zinc Zinc
Tin Iron
Lead Nickel
6. Tenacity or toughness. Tenacity or toughness is the strength with which the material
opposes rupture. It is due to the attraction which the molecules have for each other ; giving them
power to resist tearing apart.
The area under the stress-strain curve indicates the toughness (i.e., energy which can be
absorbed by the material upto the point of rupture). Although the engineering stress-strain curve is
often used for this computation, a more realistic result is obtained from the true stress-true strain
curve. Toughness is expressed as energy absorbed Nm per unit of volume of material participating
in absorption (m
3
), or Nm/m
3
. This result is obtained by multiplying the ordinate by the abscissa (in
appropriate units) of stress-strain plot.
7. Brittleness. Lack of ductility is brittleness. When a body breaks easily when subjected to
shocks it is said to be brittle.
8. Hardness. Hardness is usually defined as resistance of a material to penetration. Hard
materials resist scratches or being worn out by friction with another body.
Hardness is primarily a function of the elastic limit (i.e., yield strength) of the material and to
a lesser extent a function of the work hardening coefficient. The modulus of elasticity also exerts a
slight effect on hardness.
In the most generally accepted tests, an indenter is pressed into the surface of the material
by a slowly applied known load, and the extent of the resulting impression is measured mechanically
or optically. A large impression for a given load and indenter indicates a soft material, and the
opposite is true for a small impression.
The converse of hardness is known as softness.
12.7. TENSILE TEST
The tensile test is one of the most widely used of the mechanical tests. There are many
variations of this test to accommodate the widely differing character of materials such as metals,
elastomers, plastic and glass. The tensile test on a mild steel test piece is described below:
Fig. 12.9 (a, b, c) shows different types of tensile test pieces used for the test.
SIMPLE STRESSES AND STRAINS 337
( ) a
( ) b
( ) c
Fig. 12.9. Tensile test specimens.
The tensile test is carried out on a bar of uniform cross-section throughout the gauge length.
The specimen is mounted in the jaw of a testing machine with which a gradually increasing load can
be applied. The extension or elongation of the gauge length is recorded continuously and finally a
graph is drawn between the load and extension or between stress and strain ; which is of the type
shown in Fig. 12.10 (a).
S
t
r
e
s
s
Strain
E
l
a
s
t
i
c
s
t
a
g
e
M
N
P
Q
R
S
Plastic stage
Fig. 12.10. (a) Stress-strain curve.
Upto point M Hookes law holds good and this point is known as limit of proportionality.
Beyond the point M Hookes law is not obeyed although the material remains elastic i.e., strain
completely disappears after the removal of load. At the point N elastic limit is reached. If the material
is loaded or stressed upto this point the material will regain its original shape on the removal of the
load. Upto the point P strain increases more quickly than stress ; at this point the metal yields. In
the mild steel yielding commences immediately and two points P and Q, the upper and lower yield
338 APPLIED MECHANICS
points respectively are obtained. On further increasing the load slightly, the strain increases rapidly
till R when neck or waist is formed. When this point (R) is reached the deformation or extension
continues even with lesser load and ultimately fracture occurs.
The various properties connected with this test are given more elaborately in the following
paragraphs:
(i) Proportional limit. It is the maximum stress at which stress remains directly proportional
to strain. The proportional limit is determined from the stress-strain curve by drawing a straight
line tangent at the origin and noting the first deviation of the plot from the line.
The proportional limit has limited engineering significance because of its great dependence
upon the precision available for its determination.
(ii) Elastic limit. The elastic limit is the maximum stress which the material can withstand
without causing permanent deformation which remains after retnoval of stress.
For engineering usage the elastic limit has little significance.
(iii) Yield strength. The yield strength is the stress at which a material exhibits a specified
limiting permanent set.
The yield strength of a metal is a property of considerable significance. The tensile yield
strength indicates resistance to permanent deformation produced by tensile loads. It is related to
resistance to permanent deformation by shearing, bending, compressive and complex combination
of forces. Because of this and the ease of its measurement the tensile yield strength is used widely as
a factor of design ; it is preferable in most instances to the use of tensile strength. The yield strength
also is indicative of the ease of forming or shaping metals by mechanical stress.
(iv) Yield point. The yield paint is the stress at which there first occurs a marked increase in
strain without an increase in stress. The yield point can be determined by noting the first load at
which there is visible increase in the distance between two gauge marks on a tensile specimen. This
is conveniently accomplished by checking the length with a pair of dividers. If an extensometer is
used, the length can be observed to increase rapidly without an increase in load. Still a third method
is to coat the specimen with a brittle lacquer which cracks when the yield point is reached. The yield
point most commonly is observed in mild steels, although it has been detected in a few other alloys.
(v) Tensile strength (ultimate or maximum strength). It is calculated by dividing the
maximum load carried by the specimen during a tension test by the original cross-sectional area of
the specimen.
Tensile strength is widely used design factor, although there is more justification for yield
strength.
(vi) Rupture strength. It is determined by dividing the load at the time of fracture by the
original cross-sectional area. If the rupture load is divided by the actual cross-section at the time of
fracture, the time rupture strength is obtained.
The rupture strength is of indirect and limited interest to engineers. It provide the terminal
point of the stress-strain curve and makes possible a computation of static toughness.
(vii) Elongation. Elongation of a specimen after fracture may be determined by placing the
parts of the broken specimen closely together and holding them to place by a vice. The distance
between gauge marks may be measured by means of dividers.
SIMPLE STRESSES AND STRAINS 339
Percentage elongation =
Final length Original length
Original length

100
Elongation has considerable engineering significance because it indicates ductility, or the
ability to deform appreciably without rupture. Ductility is essential in forming operations for metals,
where it is desirable to achieve as much deformation as possible in one operation without danger of
calling rupture. Ductility is also essential to avoid local failures leading to overall failures in metal
members which are locally highly stressed as a result of design or fabricating techniques.
(viii) Reduction of area. After the metal has fractured the percentage reduction in area is
calculated by measuring the test piece diameter at the point of fracture, calculating the cross-sectional
area at this point, and expressing it as a percentage of original area.
Percentage reduction of area =
Original area Area at fracture
Original area

100
(ix) Proof stress is the stress at which the stress strain curve departs from a straight line by
not more than 0.1 per cent of length of the test piece. The material is said to have passed the proof
stress test if application of certain load for 15 seconds does not produce more than 0.1 per cent
elongation.
(x) Ultimate stress. The maximum load to which a bar is subjected to in a test divided by the
original cross-sectional area, gives a nominal stress which is known as ultimate or maximum stress.
A tensile ultimate stress is called Tenacity.
(xi) Working stress. The maximum (or greatest) calculated stress to which a part of machine
or structure is ever subjected to is called the working stress. It should be well below the elastic limit.
(xii) Factor of safety (F.O.S). The ratio of ultimate stress to working stress is called factor
of safety. It is also known as factor ignorance. In America it is sometimes called as he factor of
stropidity. It depends upon the following factors:
(i) nature of loading,
(ii) frequency of variation of load,
(iii) degree of reliability required, and
(iv) decrease of section by corrosion etc.
Factor of safety is decided by experience.
Stress-strain curve for brittle materials. Structural steel is the only material that exhibits
a marked yield point. Most of the other materials show a gradual change from linear to the non-
linear range. Brittle materials have a very low proportional point and do not show the yield point.
Fig. 12.10 (b) shows a typical stress-strain curve for cast iron.
Note. The stress-strains curves for compression can similarly be plotted to determine the characteristic
stresses such as proportional stress, yield stress and the ultimate stress. In case of steel these stresses are the
same both in tension and in compression.
340 APPLIED MECHANICS
Yield stress
Specified strain
Stress
Strain
Fig. 12.10 (b)
12.8. STRAIN HARDENING (OR WORK HARDENING)
When a material is subjected to plastic deformation, a certain amount of work done on it is
stored internally as strain energy. This additional energy in a crystal results in strengthening or
work hardening of solids. Thus work hardening or strain hardening may be defined as increased
hardness accompanying plastic deformation. This increase in hardness is accompanied by an increase
in both tensile and yield strength. Work hardening reduces ductility.
Strain hardening is used in many manufacturing processes such as rolling of bars and drawing
the tubes. It is also used to improve the elastic strength in the manufacture of many parts such as :
(i) Pre-stretching of hoisting chains and cables, (ii) Initial pressurisation of pressure vessel, cylinders
of hydraulic press and guns.
12.9. POISSONS RATIO
If a body is subjected to a load its length changes ; ratio of this change in length to the
original length is known as linear or primary strain. Due to this load, the dimensions of the body in
all directions at right angles to its line of applications change ; the strains thus produced are called
lateral or secondary or transverse strains and are of nature opposite to that of primary strains. For
example, if the load is tensile, there will be an increase in length and a corresponding decrease in
cross-sectional area of the body (Fig. 12.11). In this case, linear or primary strain will be tensile and
secondary or lateral or transverse strain compressive.
SIMPLE STRESSES AND STRAINS 341
Initial transverse
dimension
Final transverse
dimension
Longitudinal
elongation
Fig. 12.11
The ratio of lateral strain to linear strain is known as Poissons ratio.
i.e., Poissons ratio, =
lateral strain or transverse strain
linear or primary strain
=
1
m
where m is a constant and its value varies between 3 and 4 for different materials.
Table 12.1 gives the average values of Poissons ratio for common materials.
Table 12.1. Poissons Ratio for Some of the Common Materials
S. No. Material Poissons ratio
1 Aluminium 0.330
2 Brass 0.340
3 Bronze 0.350
4 Cast iron 0.270
5 Concrete 0.200
6 Copper 0.355
7 Mone 0.315
8 Steel 0.288
9 Stainless steel 0.305
10 Wrough iron 0.278
12.10. RELATIONS BETWEEN THE ELASTIC MODULII
Relations exist between the elastic constants for any specific materials and these relations
hold good for all materials within the elastic range. The relations result from the fact that the
application of any particular type of stress necessarily produces other types of stress on other places
in the material. Further, each of the stresses produces its corresponding strain and all the strains
produced must be consistent.
342 APPLIED MECHANICS
12.10.1. Relation between E and C
Refer to Fig. 12.12. LMST is a solid cube subjected to a shearing force F. Let f
s
be the shear
stress produced in the faces MS and LT due to this shearing force. The complementary shear stress
consequently produced in the faces ML and ST is also f
s
. Due to the shearing load the cube is distorted
to LMS T, and as such, the edge M moves to M, S to S and the diagonal LS to LS.
45
S M M S F
L
f f
T
N
C
o
m
p
r
e
s
s
iv
e
s
t
r
e
s
s
T
e
n
s
i
l
e s
t
r
e
s
s
f
s
f
s
f
s
f
s
Fig. 12.12
Shear strain = =
SS
ST

Also shear strain =

f
C
s

SS
ST
f
C
s

= ...(i)
On the diagonal LS, draw a perpendicular SN to S.
Now diagonal strain =
NS
LN
NS
LS

=

...(ii)
NS = SS cos 45 =
SS
2
[LST is assumed to be equal to LST since SS is very small]
and LS = ST 2
Putting the value of LS in (ii), we get
Diagonal strain =
SS
ST
SS
ST

=

2 2
2
But
SS
ST
f
C
s

=
Diagonal strain =
f
C
f
C
s n
2 2
= ...(iii)
where f
n
is the normal stress due to shear stress f
s
. The net strain in the direction of diagonal LS
SIMPLE STRESSES AND STRAINS 343
=
f
E
f
mE
n n
+
Since the diagonals and have normal
tensile and compressive stress respectively.
LS MT
f
n
L
N
M
O
Q
P
=
f
E m
n
1
1
+
F
H
G
I
K
J ...(iv)
Comparing (iii) and (iv), we get

f
C
f
m m
n n
2
1
1
= +
F
H
G
I
K
J i.e., E = 2C
1
1
+
F
H
G
I
K
J
m
...(12.7)
12.10.2. Relation between E and K
If the solid cube in question is subjected to f
n
(normal compressive stress) on all the faces, the
direct strain in each axis =
f
mE
n
(compressive) and lateral strain in other axis =
f
mE
n
(tensile).
Net compressive strain in each axis
=
f
E
f
mE
f
mE
f
E m
n n n n
=
F
H
G
I
K
J 1
2
Volumetric strain (e
v
) in this case will be,
e
v
= 3 linear strain = 3
f
E m
n
1
2

F
H
G
I
K
J
But e
v
=
f
K
n

f
K
f
E m
n n
=
F
H
G
I
K
J
3
1
2
or E = 3K 1
2

F
H
G
I
K
J
m
...(12.8)
The relation between E, C and K can be established by eliminating m from the equations
(12.7) and (12.8) as follows :
From equation (12.7), m =
2
2
C
E C
.
Putting this value in equation (12.8), we get
E = 3K 1
2
2
2

L
N
M
M
M
M
O
Q
P
P
P
P
C
E C
or E = 3K 1
2

F
H
G
I
K
J
E C
C
or
E
K
C E C
C
C E
C 3
2 3
=
+
=

or
E
K
E
C 3
+
= 3
or EC + 3KE = 9KC
E (3K + C) = 9KC
E =
9
3
KC
K C +
...(12.9)
Note. When a square or rectangular block subjected to a shear load is in equilibrium, the shear stress in
one plane is always associated with a complementary shear stress (of equal value) in the other plane at right
angles to it.
344 APPLIED MECHANICS
12.11. STRESSES INDUCED IN COMPOUND TIES OR STRUTS
Frequently ties consist of two materials, rigidly fastened together
to prevent uneven straining of the two materials. In these cases, it is
interesting to calculate the distribution of the load between the materials.
It will be assumed that the two materials are symmetrically distributed
about the axis of the bar, as with a cylindrical rod encased in a tube
(Fig. 12.13). If then an axial load W is applied to the bar
W = f
1
A
1
+ f
2
A
2
...(12.10)
where f
1
and f
2
are the stresses induced and A
1
and A
2
are the cross
sectional areas of the materials.
The strains produced, e
1
and e
2
are equal.
e
1
= e
2

f
E
f
E
1
1
2
2
=
f
f
E
E
1
2
1
2
= ...[12.10 (a)]
Hence the stresses are in the ratio of the elastic modulii.
12.12. THERMAL STRESSES AND STRAINS
If the temperature of a body is lowered or raised ; its dimensions will decrease or increase
correspondingly. If these changes, however, are checked; the stresses thus developed in the body are
called temperature stresses and corresponding strains are called temperature strains.
Let l = length of a bar of uniform cross-section
t
1
= initial temperature of the bar
t
2
= final temperature of the bar
= co-efficient of linear expansion.
The extension in the bar due to rise in temperature will be = (t
2
t
1
) l.
If this elongation in bar is prevented by some external force or by fixing bar ends, temperature
strain thus produced will be given by
Temperature strain =
( ) t t l
l
2 1

= (t
2
t
1
) (compressive) ...(12.11)
Temperature stress developed = (t
2
t
1
)E (compressive) ...(12.12)
If, however, the temperature of the bar is lowered, the temperature strain and stress will be
tensile in nature.
STRESS-STRAIN AND YOUNGS MODULUS
Example 12.1. A square steel rod 20 mm 20 mm in section is to carry an axial load
(compressive) of 100 kN. Calculate the shortening in a length of 50 mm. E = 2.14 10
8
kN/m
2
.
Sol. Area, A = 0.02 0.02 = 0.0004 m
2
; Length, l = 50 mm or 0.05 m
Load, P = 100 kN ; E = 2.14 10
8
kN/m
2
Tube
(2)
Rod
(1)
W
Fig. 12.13
SIMPLE STRESSES AND STRAINS 345
Shortening of the rod, l :
Stress, =
P
A
=
100
0 0004 .
= 250000 kN/m
2
Also E =
stress
strain
or Strain =
stress
E
=

250000
214 10
8
.
or
l
l
=

250000
2 14 10
8
.
l =
250000
2 14 10
250000
2 14 10
8 8
. .
=

l 0.05 = 0.0000584 m or 0.0584 mm

Hence the shortening of the rod = 0.0584 mm. (Ans.)
Example 12.2. A hollow cast-iron cylinder 4 m long, 300 mm outer diameter and thickness of
metal 50 mm is subjected to a central load on the top when standing straight. The stress produced is
75000 kN/m
2
. Assume Youngs modulus for cast iron as 1.5 10
8
kN/m
2
and find (i) magnitude of
the load, (ii) longitudinal strain produced and (iii) total decrease in length.
Sol. Outer diameter, D = 300 mm = 0.3 m
Thickness, t = 50 mm = 0.05 m
Length, l = 4 m
Stress produced, = 75000 kN/m
2
E = 1.5 10
8
kN/m
2
Here diameter of the cylinder, d = D 2t = 0.3 2 0.05 = 0.2 m
(i) Magnitude of the load P :
Using the relation, =
P
A
or P = A = 75000

4
(D
2
d
2
) = 75000

4
(0.3
2
0.2
2
)
or P = 2945.2 kN. (Ans.)
(ii) Longitudinal strain produced, e :
Using the relation,
Strain, e =
stress
E
=

75000
15 10
8
.
= 0.0005. (Ans.)
(iii) Total decrease in length, l :
Using the relation,
Strain =
change in length
original length
=
l
l
0.0005 =
l
4
l = 0.0005 4 m = 0.002 m = 2 mm
Hence decrease in length = 2 mm. (Ans.)
346 APPLIED MECHANICS
Example 12.3. The following observations were made during a tensile test on a mild steel
specimen 40 mm in diameter and 200 mm long.
Elongation with 40 kN load (within limit of proportionality), l = 0.0304 mm
Yield load = 161 kN
Maximum load = 242 kN
Length of specimen at fracture = 249 mm
Determine :
(i) Youngs modulus of elasticy (ii) Yield point stress
(iii) Ultimate stress (iv) Percentage elongation.
Sol. (i) Youngs modulus of elasticity E :
Stress, =
P
A
=

40
4
0 04)
2

( .
= 3.18 10
4
kN/m
2
Strain, e =
l
l
=
0 0304
200
.
= 0.000152
E =
stress
strain
=
3 18 10
0 000152
4
.
.
= 2.09 10
8
kN/m
2
. (Ans.)
(ii) Yield point stress :
Yield point stress =
yield point load
area
=
161
4

( . 0 04)
2
= 12.8 10
4
kN/m
2
. (Ans.)
(iii) Ultimate stress :
Ultimate stress =
maximum load
area
=
242
4

( . 0 04)
2
= 19.2 10
4
kN/m
2
. (Ans.)
(iv) Percentage elongation :
Percentage elongation =
length of specimen at fracture original length
original length

=
249 200
200

= 0.245 = 24.5%. (Ans.)

Example 12.4. A steel wire 2 m long and 3 mm in diameter is extended by 0.75 mm when a
weight W is suspended from the wire. If the same weight is suspended from a brass wire, 2.5 m long
and 2 mm in diameter, it is elongated by 4.64 mm. Determine the modulus of elasticity of brass if that
of steel be 2.0 10
5
N/mm
2
.
Sol. Given : l
s
= 2 m, d
s
= 3 mm, l
s
= 0.75 mm ; E
s
= 2.0 10
5
N/mm
2
;
l
b
= 2.5 m ; d
b
= 2 mm ; l
b
= 4.64 m.
SIMPLE STRESSES AND STRAINS 347
Modulus of elasticity of brass, E
b
:
From Hookes law, we know l =
Wl
AE
where, l = extension, l = length, A = cross-sectional area, and
E = modulus of elasticity.
Case I : For steel wire :
l
s
=
Wl
A E
s
s s
or 0.75 =
W

F
H
G
I
K
J
( )
.
2 1000
4
3 2 0 10
2 5

or W = 0.75

4
3
3

F
H
G
I
K
J
2.0 10
5

1
2000
...(i)
Case II : For brass wire :
l
b
=
Wl
A E
b
b b
4.64 =
W
E
b

F
H
G
I
K
J
( . ) 2 5 1000
4
2
2

or W = 4.64

4
2
1
2500
2

F
H
G
I
K
J E
b
...(ii)
Equating eqns. (i) and (ii), we get
0.75

4
3 2 0 10
1
2000
4 64
4
2
1
2500
2 5 2

F
H
G
I
K
J
=
F
H
G
I
K
J
. . E
b
or E
b
= 0.909 10
5
N/mm
2
. (Ans.)
Example 12.5. A steel bar is 900 mm long ; its two ends are 40 mm and 30 mm in diameter
and the length of each rod is 200 mm. The middle portion of the bar is 15 mm in diameter and
500 mm long. If the bar is subjected to an axial tensile load of 15 kN, find its total extension.
Take E = 200 GN/m
2
(G stands for giga and 1 G = 10
9
)
Sol. Refer to Fig. 12.14.
Load, P = 15 kN
Area, A
1
=

4
40
2
= 1256.6 mm
2
= 0.001256 m
2
Area, A
2
=

4
15
2
= 176.7 mm
2
= 0.0001767 m
2
Area, A
3
=

4
30
2
= 706.8 mm
2
= 0.0007068 m
2
Lengths : l
1
= 200 mm = 0.2 m, l
2
= 500 mm = 0.5 m and l
3
= 200 mm = 0.2 m
4
0
m
m
d
i
a
3
0
m
m
d
i
a
1
5
m
m
d
i
a
2
200 mm 200 mm 500 mm
1
Fig. 12.14
348 APPLIED MECHANICS
Total extension of the bar :
Let l
1
, l
2
and l
3
be the extensions in the parts 1, 2 and 3 of the steel bar respectively.
Then, l
1
=
Pl
A E
l
Pl
A E
l
Pl
A E
1
1
2
2
2
3
3
3
, , = = E
e
P A
l l
P l
A
l
Pl
AE
= = = =
L
N
M
O
Q
P

/
/
.
.
or
Total extension of the bar,
l = l
1
+ l
2
+ l
3
=
Pl
A E
Pl
A E
Pl
A E
P
E
l
A
l
A
l
A
1
1
2
2
3
3
1
1
2
2
3
3
+ + = + +
L
N
M
O
Q
P
=
15 10
200 10
0 20
0 001256
0 50
0 0001767
0 20
0 0007068
3
9

+ +
L
N
M
O
Q
P
.
.
.
.
.
.
= 0.0002454 m = 0.2454 mm
Hence total extension of the steel bar = 0.2454 mm. (Ans.)
Example 12.6. The bar shown in Fig. 12.15 is subjected to a tensile load of 50 kN. Find the
diameter of the middle portion if the stress is limited to 130 MN/m
2
. Find also the length of the
middle portion if the total elongation of the bar is 0.15 mm. Take E = 200 GN/m
2
.
Sol. Magnitude of tensile load, P = 50 kN
Stress in the middle portion, = 130 MN/m
2
Total elongation of the bar, l = 0.15 mm = 0.15 10
3
m
Modulus of elasticity, E = 200 GN/m
2
Diameter of the middle portion, d :
Now, stress in the middle portion, =
P
A d
=
50 1000
4)
2
( /
= 130 10
6
d =
50 1000
4 130 10
6
1/ 2

L
N
M
O
Q
P
/
= 0.0221 m or 22.1 mm
Hence diameter of the middle portion = 22.1 mm. (Ans.)
x
250 mm
40 mm
dia
40 mm
dia
d
50 kN 50 kN
Fig. 12.15
Length of the middle portion :
Let the length of the middle portion = x metre
Stress in the end portions, =
50 1000
4
40
1000
2

F
H
G
I
K
J /
= 39.79 10
6
N/m
2
Elongation of the end portion =
( . ) 0 25 x
E
SIMPLE STRESSES AND STRAINS 349
Also, elongation of the end portion + extension of the middle portion = 0.15 10
3
39 79 10 0 25
200 10
130 10
200 10
6
9
6
9
. ( . )

x x
= 0.15 10
3
39.79 10
6
(0.25 x) + 130 10
6
x = 200 10
9
0.15 10
3
Dividing both sides by 39.79 10
6
, we get
0.25 x + 3.267 x = 0.754
x = 0.222 m or 222 mm
Hence length of the middle portion = 222 mm. (Ans.)
Example 12.7. A steel tie rod 50 mm in diameter and 2.5 m long is subjected to a pull of
100 kN. To what length the rod should be bored centrally so that the total extension will increase by
15 percent under the same pull, the bore being 25 mm diameter ? Take E = 200 GN/m
2
.
Sol. Refer to Fig. 12.16 (a), (b)
l = 2.5 m
x
25 mm dia
100 kN 100 kN
5
0
m
m
(a)
(b)
Fig. 12.16
Diameter of the steel tie rod = 50 mm = 0.05 m
Length of the steel rod, l = 2.5 m
Magnitude of the pull, P = 100 kN
Diameter of the bore = 25 mm = 0.025 m
Modulus of elasticity, E = 200 10
9
N/m
2
Length of the bore, x :
Stress in the solid rod, =
P
A
=

100 1000
4 005
2
/ ( . )
= 50.92 10
6
N/m
2
Elongation of the solid rod, l =
l
E
=

50 92 10 2 5
200 10
6
9
. .
= 0.000636 m or 0.636 mm
Elongation after the rod is bored = 1.15 0.636 = 0.731 mm
Area at the reduced section = /4 (0.05
2
0.025
2
) = 0.001472 m
2
Stress in the reduced section, =
100 1000
0 001472

.
= 67.93 10
6
N/m
2
Elongation of the rod =
( . ) . 2 5
+
x
E
x
E
= 0.731 10
3
350 APPLIED MECHANICS
=
50 92 10 2 5
200 10
67 9 10
200 10
6
9
6
9
. ( . ) .

x x
= 0.731 10
3
= 50.92 10
6
(2.5 x) + 67.9 10
6
x
= 200 10
9
0.731 10
3
= (2.5 x) + 1.33 x = 2.87
or x = 1.12 m
Hence length of the bore = 1.12 m. (Ans.)
Example 12.8. A brass bar having cross-sectional area of 1000 mm
2
is subjected to axial
forces shown in Fig. 12.17. Find the total elongation of the bar. Modulus of elasticity of brass
= 100 GN/m
2
.
Sol. Refer to Fig. 12.17. The loading of three different portions LM, MN and NP is shown
separately in the Fig. 12.18. It may be noted that portion LM is under the tensile force 50 kN to the
left, and to the right of it, there is again an effective force 50 kN which is a resultant of three forces
to its right
i.e., (80 20 10) = 50 kN.
80 kN
20 kN
10 kN
M
L
N
50 kN
0.6 m 1.0 m 1.2 m
P
Fig. 12.17
Similarly in portion MN, the compressive force on the left is 30 kN (i.e., 80 50) and 30 kN on
the right (i.e., 20 + 10). In NP, the compressive load is 10 kN, (i.e., 80 50 20) and on the right,
there is already a compressive load of 10 kN. So we observe that the bar is in equilibrium under the
action of these forces.
50 kN
50 kN
10 kN
10 kN 30 kN 30 kN
L M M N N P
1.2 m 1.0 m 0.6 m
Fig. 12.18
Total elongation of the bar :
Let l
1
, l
2
and l
3
be the changes in length LM, MN and NP respectively.
Then, l
1
=
Pl
AE
1 1
...... increase (+)
l
2
=
P l
AE
2 2
...... decrease ()
l
3
=
P l
AE
3 3
...... decrease ()
SIMPLE STRESSES AND STRAINS 351
Net change in length, l = l
1
l
2
l
3
=
Pl
AE
P l
AE
P l
AE AE
1 1 2 2 3 3
1
= (P
1
l
1
P
2
l
2
P
3
l
3
)
=
10
1000 10 100 10
3
6 9

(50 0.6 30 1 10 1.2)

=
1
10
5
(30 30 12) =
1
10
5
( 12)
= 0.00012 m = 0.12 mm
Negative sign indicates that the bar is shortened by 0.12 mm. (Ans.)
Example 12.9. In Fig. 12.19 is shown a steel bar of cross-sectional area 250 mm
2
held firmly
by the end supports and loaded by an axial force of 25 kN.
Determine :
(i) Reactions at L and M. (ii) Extention of the left portion.
E = 200 GN/m
2
.
Sol. Refer to Fig. 12.19.
(i) Reactions at L and M :
As the bar is in equilibrium
R
L
+ R
M
= 25 kN ...(i)
Also, since total length of the bar
remains unchanced,
Extension in LN = contraction in MN

R
A E
R
A E
L M

0 25 0 6 . .
R
L
0.25 = R
M
0.6
R
L
=
R
M
0 6
0 25
.
.
= 2.4 R
M
Substituting the value of R
L
in (i), we get 2.4 R
M
+ R
M
= 25
From which R
M
= 7.353 kN. (Ans.)
R
L
= 25 7.353 = 17.647 kN. (Ans.)
(ii) Extention of left portion :
Extention of left portion =
R
A E
L

0 25 17 647 10 0 25
250 10 200 10
3
6 9
. . .
= 0.0000882 m
= 0.0882 mm. (Ans.)
R
L
R
M
L N M
25 kN
0.25 m 0.6 m
Fig. 12.19
352 APPLIED MECHANICS
Example 12.10. Two parallel steel wires 6 m long, 10 mm diameter are hung vertically
70 mm apart and support a horizontal bar at their lower ends. When a load of 9 kN is attached to one
of the wires, it is observed that the bar is 24 to the horizontal. Find E for wire.
Sol. Refer to Fig. 12.20.
Two wires LM and ST made of steel, each 6 m long and 10 mm
diameter are fixed at the supports and a load of 9 kN is applied on
wire ST. Let the inclination of the bar after the application of the
load be .
The extension in the length of steel wire ST,
l = 70 tan = 70 tan 2.4 = 70 0.0419 = 2.933 mm
= 0.00293 m
Strain in the wire, e =
l
l
=
0 00293
6
.
= 0.000488
and stress in the wire
=
P
A
=

F
H
G
I
K
J
9000
4
10
1000
2

= 11.46 10
7
N/m
2
Youngs modulus, E =

e
=
1146 10
0 000488
7
.
.
= 235 10
9
N/m
2
= 235 GN/m
2
. (Ans.)
Example 12.11. A concrete cylinder of diameter 150 mm and length 300 mm when subjected
to an axial compressive load of 240 kN resulted in an increase of diameter by 0.127 mm and a decrease
in length of 0.28 mm. Compute the value of Poissons ratio =
F
H
G
I
K
J
1
m
and modulus of elasticity E.
Sol. Diameter of the cylinder, d = 150 mm
Length of the cylinder, l = 300 mm
Increase in diameter, d = 0.127 mm (+)
Decrease in length, l = 0.28 mm ()
Axial compressive load, P = 240 kN
Poissons ratio, :
We know that,
Linear strain =
l
l
=
0 28
300
.
= 0.000933
and, lateral strain =
d
d
=
0 127
150
.
= 0.000846
Poissons ratio, =
lateral strain
linear strain
0.000846
0.000933
= = 0.907
L S
70 mm
q
T
T
M
9 kN
6
m
Fig. 12.20
SIMPLE STRESSES AND STRAINS 353
Modulus of elasticity, E :
Using the relation, E =
stress
strain (linear)
=
P A
l l
/
/
E =
240 4 0 15
0 00028
0 3
240 4 0 3
0 15 0 00028
2
2
/ ( / . )
.
.
.
. .

F
H
G
I
K
J
=


= 14.55 10
6
kN/m
2
= 14.55 GN/m
2
Youngs modulus, E = 14.44 GN/m
2
. (Ans.)
Example 12.12. For a given material, Youngs modulus is 110 GN/m
2
and shear modulus is
42 GN/m
2
. Find the bulk modulus and lateral contraction of a round bar of 37.5 mm diameter and
2.4 m long when stretched 2.5 mm.
Sol. Youngs modulus, E = 110 GN/m
2
Shear modulus, C = 42 GN/m
2
Diameter of round bar, d = 37.5 mm = 0.0375 m
Length of round bar, l = 2.4 m
Extension of bar, l = 2.5 mm = 0.0025 m
Bulk modulus, K :
We know that, E = 2C 1
1
+
F
H
G
I
K
J
m
110 10
9
= 2 42 10
9
1
1
+
F
H
G
I
K
J
m

1
m
= 1.31 1 = 0.31 or m =
1
0 31 .
= 3.22
Substituting this value of m in the equation
K =
mE
m
K
3 2
3 22 110 10
3 3 22 2
9
( )
.
( . )
=

= 96.77 GN/m
2
. (Ans.)
Lateral contraction, d :
Longitudinal strain,
l
l
=
0 0025
2 4
.
.
= 0.00104
and lateral strain = 0.00104
1
m
= 0.00104
1
3 22 .
= 0.000323
Lateral contraction, d = 0.000323 d = 0.000323 37.5 = 0.0121 mm. (Ans.)
Example 12.13. The following data relate to a bar subjected to a tensile test :
Diameter of the bar, d = 30 mm (= 0.03 m)
Tensile load, P = 54 kN
Gauge length, l = 300 mm (= 0.3 m)
Extension of the bar, l = 0.112 mm
Change in diameter, l = 0.00366 mm
Calculate : (i) Poissons ratio (ii) The values of three moduli.
354 APPLIED MECHANICS
Sol. (i) Poissons ratio
1
m
or () :
Stress, =
P
A d
= =

54
4
54
4
0 03
2
2

/
( . )
= 76394 kN/m
2
= 76.4 MN/m
2
Linear strain =
l
l
=
0 112
30
.
= 3.73 10
4
Lateral strain =
d
d
=
0 00366
30
.
= 1.22 10
4
Poissons ratio, =
1 122 10
3 73 10
4
4
m
= =

lateral strain
linear strain
.
.
= 0.327. (Ans.)
(ii) The values of three moduli, E, C and K :
We know that, E =
stress
strain
=

76 4
3 73 10
4
.
.
= 2.05 10
5
MN/m
2
. (Ans.)
Also, E = 2C 1
1
+
L
N
M
O
Q
P
m
[Eqn. 12.7]
or C =
E
m
2 1
1
2 05 10
2 1 0 327
5
+
L
N
M
O
Q
P
=

+
.
( . )
= 0.77 10
5
MN/m
2
. (Ans.)
Again E = 3K 1
2

L
N
M
O
Q
P
m
K =
E
m
3 1
2
2 05 10
3 1 2 0 327
5

L
N
M
O
Q
P
=


.
( . )
= 1.97 10
5
MN/m
2
. (Ans.)
Example 12.14. A concrete column of cross-sectional area 400 mm 400 mm is reinforced by
four longitudinal 50 mm diameter round steel bars placed at each corner. If the column carries a
comprehensive load of 300 kN, determine :
(i) Loads carried ;
(ii) The compressive stress produced in the concrete and steel bars.
Youngs modulus of elasticity of steel is 15 times that of concrete.
Sol. Refer to Fig. 12.21.
Cross-sectional area of the column
= 0.4 0.4 = 0.16 m
2
Area of steel bars,
A
s
= 4 /4 (0.05)
2
= 0.00785 m
2
Area of concrete,
A
c
= 0.16 0.00785 = 0.1521 m
2
Since the steel bars and concrete shorten by
the same amount under the compressive load,
Strain in steel bars = strain in concrete
or e
s
= e
c


s
s
c
c
E E
=
or
s
=
c
.
E
E
s
c
= 15
c
( E
s
= 15E
c
)
400 mm
4
0
0
m
m
Concrete
Steel bar
50 mm dia.
Fig. 12.21
SIMPLE STRESSES AND STRAINS 355
Also load shared by steel bars + load shared by concrete = 300000 N
P
s
+ P
c
= 300000 N
or
s
A
s
+
c
A
c
= 300000
15
c
0.00785 +
c
0.1521 = 300000

c
(15 0.00785 + 0.1521) = 300000

c
= 1.11 10
6
N/m
2
= 1.11 MN/m
2

s
= 15
c
= 15 1.11 10
6
= 16.65 10
6
N/m
2
= 16.65 MN/m
2
Load carried by steel bars, P
s
=
s
A
s
= 16.65 10
6
0.00785
= 130.7 kN ~

131 kN. (Ans.)

Load carried by concrete, P
c
= 1.11 10
6
0.1521 = 168.9 ~

169 kN. (Ans.)

Example 12.15. A copper rod of 40 mm diameter is surrounded tightly by a cast iron tube
of 80 mm external diameter, the ends being firmly fastened together. When put to a compressive load
of 30 kN, what load will be shared by each ? Also determine the amount by which the compound bar
shortens if it is 2 m long.
Take E
c.i.
= 175 GN/m
2
and E
c
= 75 GN/m
2
.
Sol. Refer to Fig. 12.22.
Diameter of the copper rod = 0.04 m
Area of copper rod,
A
c
=

4
0.04
2
= 0.0004 m
2
External diameter of cast iron tube = 0.08 m
Area of cast iron tube,
A
c.i.
=

4
(0.08
2
0.04
2
) = 0.0012 m
2
We know that,
Strain in cast iron tube = strain in the copper rod


c i
c i
c
c
E E
. .
. .
=
or

c i
c
c i
c
E
E
. . . .
= =

175 10
75 10
9
9
= 2.33

c.i.
= 2.33
c
...(i)
Also, total load = load shared by cast iron tube
+ load shared by copper rod.
or P = P
c.i.
+ P
c
30 =
c.i.
. A
c.i.
+
c
. A
c
or 30 =
c.i.
0.0012 +
c
0.0004 ...(ii)
40 mm
80 mm
30 kN
dl
Cast iron
tube
Copper rod
2
m
Fig. 12.22
356 APPLIED MECHANICS
Substituting the value of
c.i.
from (i) in (ii), we get
30 = 2.33
c
0.0012 +
c
0.0004
=
c
(0.008785 + 0.001257) = 0.010042
c

c
=
30
0 010042 .
= 2987.5 kN/m
2
And from equation (i),

c.i
= 2.33
c
= 2.33 2987.5 = 6960.8 kN/m
2
Load shared by the copper rod,
P
c
=
c
A
c
= 2987.5 0.0004 = 3.75 kN. (Ans.)
Load shared by cast iron tube,
P
c.i.
= 30 3.75 = 26.25 kN. (Ans.)
Strain =

c
c
E
or

c
c
E
l
l
= =
decrease in length
original length
l =

c
c
E
l =
2987.5 10
75 10
3
9

2 = 0.0000796 m or 0.0796 mm
Hence decrease in length = 0.0796 mm. (Ans.)
Example 12.16. A solid steel cylinder 500 mm long and 70 mm diameter is placed inside an
aluminium cylinder having 75 mm inside diameter
and 100 mm outside diameter. The aluminium
cylinder is 0.16 mm longer than the steel cylinder.
An axial load of 500 kN is applied to the bar and
cylinder through rigid cover plates as shown in
Fig. 12.23. Find the stresses developed in the steel
cylinder and aluminium tube. Assume for steel, E
= 220 GN/m
2
and for aluminium E = 70 GN/m
2
.
Sol. Refer to Fig. 12.23.
Since the aluminium cylinder is 0.16 mm
longer than the steel cylinder, the load required to
compress this cylinder by 0.16 mm will be found as
follows :
E =
stress
strain
= =
P A
l l
Pl
A l
/
/ .
or P =
E A l
l
. .
=
70 10 / 4(0.1 0.075) 0.00016
0.50016
9 2 2

= 76944 N
0.16 mm
Aluminium
cylinder
Steel
cylinder
Rigid plate
70 mm
75 mm
100 mm
500 kN
5
0
0
m
m
500 kN Rigid plate
Fig. 12.23
SIMPLE STRESSES AND STRAINS 357
When the aluminium cylinder is compressed by its extra length 0.16 mm, the load then shared
by both aluminium as well as steel cylinder will be,
500000 76944 = 423056 N
Let e
s
= strain in steel cylinder
e
a
= strain in aluminium cylinder

s
= stress produced in steel cylinder

a
= stress produced in aluminium cylinder
E
s
= 220 GN/m
2
E
a
= 70 GN/m
2
As both the cylinders are of the same length and are compressed by the same amount,
e
s
= e
a
or

s
s
a
a
E E
= or
s
=
E
E
a
s
.
a
=
220 10
9

70 10
9

a
=
22
7

a
Also P
s
+ P
a
= P
or
s
. A
s
+
a
. A
a
= 423056

22
7

a
A
s
+
a
A
a
= 423056

a
=
423056
22
423056
22
7 4
0 07
4
0 1 0 075
2 2 2
7
A A
s a
+
=
+

. ( . . )
=
423056
0.012095 0.003436 +
= 27.24 10
6
N/m
2
= 27.24 MN/m
2
and
s
=
22
7
27.24 = 85.61 MN/m
2
Stress in the aluminium cylinder due to load 76944 N
=
76944
4
0 1 0 075
2 2

( . . )
= 23.39 10
9
N/m
2
= 22.39 MN/m
2
Total stress in aluminium cylinder
= 27.24 + 22.39 = 49.63 MN/m
2
. (Ans.)
and stress in steel cylinder = 85.61 MN/m
2
. (Ans.)
Example 12.17. A beam weighing 450 N is held in a horizontal position by three vertical
wires, one attached to each end of the beam, one to the middle of its length. The outer wires are of
brass of diameter 1.25 mm and the central wire is of diameter 0.625 mm. If the beam is rigid and
wires of the same length and unstressed before the beam is attached, estimate the stresses induced in
the wires. Take Youngs modulus for brass as 86 GN/m
2
and for steel 210 GN/m
2
.
Sol. Refer to Fig. 12.24.
Let P
b
= load taken by the brass wire, P
s
= load taken by the steel wire.
Then 2P
b
+ P
s
= P ...(i)
Since the beam is horizontal, all wires will extend by the same amount.
i.e., e
b
= e
s
( length of each wire is same)
where e
b
= strain in brass wire, and
e
s
= strain in steel wire.
358 APPLIED MECHANICS

b
b
s
s
E E
=
P
A E
P
A E
b
b b
s
s s
. .
=
or P
s
=
P A E
A E
b s s
b b
.
.
=
P
b

4
0 625 10 210 10
4
125 10 86 10
3 2 9
3 2 9
( . )
( . )
or P
s
= 0.61 P
b
...(ii)
Substituting the value of P
s
in equation (i), we get
2P
b
+ 0.61 P
b
= P
2.61 P
b
= 450
P
b
= 172.4 N
and P
s
= 0.61 172.4 = 105.2 N
Now, stress, induced in the brass wire,

b
=
P
A
b
b
=

172.4
4
(1.25 10 )
3 2

= 1.40 10
8
N/m
2
= 140 MN/m
2
. (Ans.)
and stress induced in a steel wire,

s
=
105.2
4
(0.625 10 )
3 2

= 3.429 10
8
N/m
2
= 342.9 MN/m
2
. (Ans.)
Example 12.18. A steel rod 15 m long is at a temperature of 15C. Find the free expansion of
the length when the temperature is raised to 65C. Find the temperature stress produced when :
(i) The expansion of the rod is prevented ;
(ii) The rod is permitted to expand by 6 mm.
Take = 12 10
6
perC and E = 200 GN/m
2
.
Sol. Free expansion of the rod = l (t
2
t
1
) = 15 12 10
6
(65 15)
= 0.009 m = 9 mm
(i) When the expansion is fully prevented :
Temperature stress = (t
2
t
1
) E = 12 10
6
(65 15) 200 10
9
= 120 10
6
N/m
2
= 120 MN/m
2
. (Ans.)
(ii) When the rod is permitted to expand by 6 mm :
In this case, the amount of expansion prevented = 9 6 = 3 mm
Strain, e =
Expansion prevented
Original length
=

3
15 1000
= 0.0002
Temperature stress = e E = 0.0002 200 10
9
= 40 10
6
N/m
2
= 40 MN/m
2
. (Ans.)
Beam
l
B
r
a
s
s
w
i
r
e
B
r
a
s
s
w
i
r
e
S
t
e
e
l
w
i
r
e
P = 450 N
Fig. 12.24
SIMPLE STRESSES AND STRAINS 359
Example 12.19. A copper flat measuring 60 mm 30 mm is brazed to another 60 mm 60 mm
mild steel flat as shown in Fig. 12.25. If the combination is heated through 120C, determine :
(i) The stress produced in each of the bar ;
(ii) Shear force which tends to rupture the brazing ; and
(iii) Shear stress.
Take,
c
= 18.5 10
6
per C

s
= 12 10
6
per C
E
c
= 110 GN/m
2
E
s
= 220 GN/m
2
Length of each flat = 400 mm.
Sol. Refer to Fig. 12.25.
(i) Stress produced in each bar :
As
c
is greater than
s
, therefore extension of copper flat will be more than that of steel flat,
but since they are brazed together, the former will try to pull the latter and the latter to push the
former ; finally, however, they will become stable at certain position pp after compromise.
Increase in length of copper flat, qm =
c
(t
2
t
1
) l
Increase in length of steel flat, qn =
s
(t
2
t
1
) l
Now compressive strain in copper flat,
e
c
=
pm
l
qm qp
l
=

or e
c
=
qm
l
qp
l

=
c
(t
2
t
1
) e ...(i)
where
qp
l
= e = common strain
Tensile strain in steel, e
s
=
np
l
qp qn
l
=

= e
s
(t
2
t
1
) ...(ii)
Adding (i) and (ii), we get
e
c
+ e
s
=
c
(t
2
t
1
)
s
(t
2
t
1
) = (
c

s
) (t
2
t
1
)
But, e
c
=

c
c
E
, e
s
=

s
s
E
or

c
c
s
s
E E
+ = (
c

s
) (t
2
t
1
)
or

c s
110 10 220 10
9 9

= (18.5 10
6
12 10
6
) 120
or 2
c
+
s
= 220 10
9
120 (18.5 10
6
12 10
6
)
or 2
c
+
s
= 171.6 10
6
...(iii)
At position pp,
Pull on steel = push on copper

s
. A
s
=
c
. A
c

s

60
1000
60
1000
=
c

60
1000
30
1000

s
=

c
2
= 0.5
c
Putting this value of
s
in (iii), we get
2
c
+ 0.5
c
= 171.6 10
6

c
= 68.64 10
6
N/m
2
= 68.64 MN/m
2
. (Ans.)
and
s
= 0.5
c
= 34.32 MN/m
2
. (Ans.)
Fig. 12.25
400 mm
q
q
p
p
m
Push
Pull
n
Copper
Steel
30 mm
60 mm
360 APPLIED MECHANICS
(ii) Shear force :
Shear force =
s
. A
s
= (
c
. A
c
) = 34.32 10
6

60
1000
60
1000

= 123552 or 123.552 kN. (Ans.)

(iii) Shear stress :
Shear stress =
shear force
shear area
=

123552
400
1000
60
1000
= 5.148 10
6
N/m
2
= 5.148 MN/m
2
. (Ans.)
HIGHLIGHTS
1. A load may be defined as the combined effect of external forces acting on a body.
The loads may classified as :
(i) Dead loads, (ii) live or fluctuating loads, (iii) inertia loads or forces and (iv) centrifugal loads or forces.
Or (i) Tensile loads, (ii) compressive loads, (iii) Torsional or twisting loads, (iv) Bending loads and (v)
shearing loads, Or (i) Point loads, (ii) Distributed loads.
2. The internal resistance which the body offers to meet with the load is called stress. When any type of
simple stress develops, we can calculate the magnitude of the stress by
f =
W
A
where f = stress, W = load,
and A = area over which stress develops.
3. The strain (e) is the deformation produced by the stress.
Tensile strain, e
t
=
l
l
=
Increase in length
Original length
Compressive strain, e
c
=
l
l
=
Decrease in length
Original length
Shear strain, e
s
= tan = radian. [Since is very small]
Volumetric strain, e
v
=
V
V
.
4. Hookes law states that within elastic limit, stress varies directly as strain
i.e., Stress strain
or
Stress
Stain
= constant
Modulus of elasticity, E =
f
e
Modulus of rigidity,
C (or N or G) =
f
e
s
s
Bulk modulus of elasticity =
f
e
n
v
.
SIMPLE STRESSES AND STRAINS 361
5. The ratio of lateral strain to linear strain is known as Poissons ratio
i.e., Poissons ratio =
Lateral or secondary strain
Linear or primary strain
=
1
m
where m is a constant and its value varies between 3 and 4 for different metals.
6. Relations between elastic moduli :
E = 2C 1
1
+
F
H
G
I
K
J
m
...(i)
E = 3K 1
2

F
H
G
I
K
J
m
...(ii)
E =
9
3
KC
K C +
...(iii)
7. If the temperature of a body is lowered or raised, its dimensions will decrease or increase correspondingly.
If these changes, however, are checked, the stresses thus developed in the body are called temperature
stresses and corresponding strains are called temperature strains.
Temperature strain = (t
2
t
1
) ...(Compressive)
Temperature stress developed = (t
2
t
1
) E ... (Compressive)
OBJECTIVE TYPE QUESTIONS
Fill in the blanks:
1. A ............ may be defined as the combined effect of external forces acting on a body.
2. A ............ load is one which is considered to act at a point.
3. A ............ load is one which is spread in some manner over the length of the beam.
4. Bending and torsion stresses are classified as ............ stresses.
5. Simple stress is often called ............ stress.
6. When any type of simple stress develops, we can calculate the magnitude of the stress by, f =
W
.......
7. The ............ is the deformation produced by the body.
8. The shear strain is measured by the ............ through which the body distorts.
9. ............ strain is defined as the ratio between change in volume and original volume of the body.
10. The strains which disappear with the removal of load are termed as ............ strains.
11. The body which regains its original position on the removal of the force is called an ............ body.
12. The body is said to be ............ if the strains exist even after the removal of external force.
13. Robert Hooke discovered experimentally that within elastic limit ............ varies directly as ............
14. ............ modulus is the ratio between tensile stress and tensile strain or compressive stress and
compressive strain.
15. ............ modulus of elasticity may be defined as the ratio of normal stress (on each face of a solid cube) to
volumetric strain and is denoted by the letter K.
16. ............ of a metal is its ability to withstand various forces to which it is subjected during a test or in
service.
17. Youngs modulus is indicative of the property called ............
362 APPLIED MECHANICS
18. ............ is the property that enables the formation of a permanent deformation in a material.
19. ............ is made use of in stamping images or coins and ornamental work.
20. ............ is the ability of a metal to withstand elongation or bending.
21. ............ is the property by virtue of which a material may be hammered or rolled into thin sheets without
rupture.
22. ............ is the strength with which the material opposes rupture.
23. The area under the stress-strain curve indicates the ............
24. Lack of ductility is ............
25. ............ is usually defined as resistance of a material to penetration.
26. The converse of hardness is known as ............
27. ............ limit is the maximum stress at which stress remains directly proportional to strain.
28. ............ limit is the maximum stress which the material can withstand without causing permanent
deformation which remains after removal of stress.
29. ............ strength is the stress at which a material exhibits a specified limiting permanent set.
30. ............ point is the stress at which there first occurs a marked increase in strain without an increase in
stress.
31. ............ strength is calculated by dividing the maximum load carried by the specimen during a tension
test by the original cross-sectional area of the specimen.
32. ............ strength is determined by dividing the load at the time of fracture by the original cross-sectional
area.
33. Percentage ............ =
Final length Original length
Original length

100.
34. A tensile ultimate stress is called ............
35. The miximum (or greatest) calculated stress to which a part of machine or structure is ever subjected to
is called the ............ stress.
36. The ratio of Lateral strain to linear strain is known as ............
37. E = 2C(1 + ............ ).
38. E =
9
3
...
K C +
Answers
1. load 2. point 3. distributed 4. indirect
5. direct 6. A 7. strain 8. angle
9. Volumetric 10. elastic 11. elastic 12. plastic
13. stress, strain 14. Youngs 15. Bulk 16. Strength
17. stiffness 18. Plasticity 19. Plasticity 20. Ductility
21. Malleability 22. Toughness 23. toughness 24. brittleness
25. Hardness 26. softness 27. Proportional 28. Elastic
29. Yield 30. Yield 31. Ultimate 32. Rupture
33. elongation 34. tenacity 35. working 36. Poissons ratio
37.
1
m
38. KC.
SIMPLE STRESSES AND STRAINS 363
Theoretical Questions
1. Define the term load. How are the loads classified ?
2. What is the difference between a point load and a distributed load ?
3. What is a simple stress?
4. Define the term strain and explain the following:
(a) Tensile strain;
(b) Compressive strain;
(c) Shear strain.
5. State and explain Hookes law.
6. Define the following:
(a) Youngs modulus (b) Modulus of rigidity
(c) Bulk or volume modulus of elasticity.
7. Explain briefly any three of the following mechanical properties of metals:
(i) Strength; (ii) Elasticity;
(iii) Plasticity; (iv) Ductility;
(v) Malleability; (vi) Tenacity (or toughness);
(vii) Brittleness.
8. What is the significance of a tensile test?
9. Draw a stress-strain curve for a mild steel specimen and explain the following:
(i) Proportional limit
(ii) Elastic limit
(iii) Yield strength
(iv) Yield point
(v) Ultimate strength
(vi) Rupture strength.
10. Define the term Factor of safety and state its significance.
11. Write a short note on strain hardening.
12. Explain the term Poissons ratio.
13. Derive relations between E and C and E and K.
14. What are the temperature stresses and temperature strains?
Unsolved Examples
Stress, Strain and Youngs Modulus :
1. A bar 0.3 m long is 50 mm square in section for 120 mm of its length, 25 mm diameter for 80 mm and of
40 mm diameter for the remaining length. If a tensile force of 100 kN is applied to the bar, calculate the
maximum and minimum stresses produced in it, and the total elongation, Take E = 200 GN/m
2
and
assume uniform distribution of load over the cross-sections. [Ans. 204 MN/m
2
, 40 MN/m
2
, 0.1453 mm]
2. A brass rod 20 mm diameter was subjected to a tensile load of 40 kN. The extension of the rod was found
to be 254 divisions in the 200 mm extension metre. If each division is equal to 0.001 mm, find the elastic
modulus of brass. [Ans. 100.25 GN/m
2
]
364 APPLIED MECHANICS
3. Find the total extension of the bar, shown in Fig. 12.26 for an axial pull of 40 kN. [Ans. 0.225 mm]
180 mm 260 mm 160 mm
40 kN 40 kN
30 mm
20 mm
32.5 mm
Fig. 12.26
4. A brass bar having a cross-sectional area of 1000 mm
2
is subjected to axial forces as shown in Fig. 12.27.
Find the total change in length of the bar. Take E
s
= 105 GN/m
2
. [Ans. 0.1143 m (decrease)]
80 kN 50 kN 10 kN
20 kN
L M N P
0.6 m 1.0 m 1.2 m
Fig. 12.27
5. A tie bar has enlarged ends of square section 60 mm 60 mm as shown in Fig. 12.28. If the middle
portion of the bar is also of square section, find the size and length of the middle portion, if the stress
there is 140 MN/m
2
, the total extension of the bar is 0.14 mm.
Take E = 200 GN/m
2
. [Ans. 25 mm 25 mm, 1.79 m]
6
0

m
m
6
0

m
m
60 mm 60 mm 60 mm 60 mm
87.5 kN 87.5 kN
3 m
Fig. 12.28
6. A circular rod 0.2 m long, tapers from 20 mm diameter at one end to 10 mm diameter at the other. On
applying an axial pull of 6 kN, it was found to extend by 0.068 mm. Find the Youngs modulus of the
material of the rod. [Ans. 112.3 GN/m
2
]
7. A vertical rod 3 m long is rigidly fixed at upper end and carries an axial tensile load of 50 kN force. The
rod tapers uniformly from a diameter of 50 mm at the top to 30 mm at the bottom. Calculate the total
extension of the bar. Take density of material = 1 10
5
kg/m
3
and E = 210 GN/m
2
. [Ans. 0.6217 mm]
Composite Sections :
8. A solid steel bar, 40 mm diameter, 2 m long passes centrally through a copper tube of internal diameter
40 m, thickness of metal 5 mm and length 2 m. The ends of the bar and tube are brazed together and a
tensile load of 150 kN is applied axially to the compound bar. Find the stresses in the steel and copper,
and extension of the compound bar. Assume E
c
= 100 GN/m
2
and E
s
= 200 GN/m
2
.
[Ans. 93.1 MN/m
2
, 46.55 MN/m
2
, 0.931 mm]
9. A weight of 100 kN is suspended from a roof by two steel rods each 5 m long, joined to form an included
angle of 100. If the working stress is 56 MN/m
2
, find the diameter of the rods and the amount each is
stretched by the weight. Neglect weight of rods and take E = 210 GN/m
2
. [Ans. 42.1 mm, 1.33 mm]
SIMPLE STRESSES AND STRAINS 365
10. Three parallel wires in the same vertical plane jointly support a load of 15 kN. The middle wire is of steel
and is 1 m long, while the outer ones of brass, the length of each being 1.05 m. The area of cross-section
of each wire is 200 mm
2
. After the wires have been so adjusted as to each carry 1/3 of the load, a further
load of 35 kN is added. Find the stress in each wire and fraction of the whole load carried by the steel
wire. Take E
s
= 200 GN/m
2
and E
b
= 80 GN/m
2
. [Ans.
b
= 62.8 MN/m
2
,
s
= 124.32 MN/m
2
, 49.7%]
11. A reinforced concrete column is 300 mm 300 mm in section. The column is provided with 8 bars each
of 20 mm diameter. The column carries a load of 360 kN. Find the stresses in concrete and the steel bars.
Take E
s
= 210 GN/m
2
and E
c
= 14 GN/m
2
. [Ans. 2.87 MN/m
2
, 43.05 MN/m
2
]
12. A reinforced concrete column is 300 mm in diameter and has 4 steel bars each of 12 mm diameter
embedded in it. If the allowable stresses in steel and concrete are 65.0 MN/m
2
and 4.0 MN/m
2
respectively,
calculate the safe axial load which the column can carry. Take E
s
= 15 E
c
. [Ans. 308.078 kN]
13. A compound tube consists of a steel tube 170 mm external diameter and 10 mm thickness and an outer
brass tube 190 mm external diameter and 10 mm thickness. The two tubes are of the same length. The
compound tube carries an axial load of 1 MN. Find the stresses and the load carried by each tube
and the amount by which it shortens. Length of each tube is 0.15 m. Take E
s
= 200 GN/m
2
and
E
b
= 100 GN/m
2
. [Ans.
s
= 127.34 MN/m
2
,
b
= 63.67 MN/m
2
, P
s
= 0.64 MN, P
b
= 0.36 MN ; 0.096 mm]
14. Two steel plates each 25 mm thick, are held together with the help of 20 mm diameter steel bolts. If the
pitch of the threads is 2.5 mm, find the increase in stress in the shank of the bolt when the nut is turned
through
1
200
of a turn with respect to the head of the bolt, assuming that the plates do not deform. Take
E
s
= 205 GN/m
2
. [Ans. 51.25 MN/m
2
]
Hint. Stretch in 50 mm length of the shank, 2.5
1
200
0.0125 mm l = =
L
N
M

strain, e =
O
Q
P
0 0125
50
.
15. A rigid cross bar is supported horizontally by two vertical bars, L and M, of equal length and hanging
from their tops. The bars L and M are 0.6 m apart. The cross bars stays horizontal even after a vertical
force of 6 kN is applied to it at a point 0.4 m from M. If the stress in L is 200 MN/m
2
, find the stress in M
and the areas of cross-section of the two rods.
Take E
L
= 200 GN/m
2
and E
M
= 130 GN/m
2
. [Ans. 130 MN/m
2
, 20.0 mm
2
, 15.385 mm
2
]
16. A 28 mm diameter steel bar, 400 mm long is placed centrally within a brass tube having an inside
diameter of 30 mm and outside diameter of 40 mm. The bar is shorter in length than the tube by
0.12 mm. While the bar and tube are held vertically on a rigid horizontal plateform, a compressive force
of 60 kN is applied at the top of the tube through a rigid plate. Determine the stresses induced in both
the bar and the tube. Take E
s
= 200 GN/m
2
and E
b
= 100 GN/m
2
.
[Ans. 48.85 MN/m
2
(Comp.) ; 54.42 MN/m
2
(Comp.)]
17. A vertical tie of uniform strength is 18 m long. If the area of the bar at the lower end is 500 mm
2
, find the
area at the upper end when the tie is to carry a load of 700 kN. The material of the tie weighs
8 10
5
N/mm
3
. [Ans. 500.5 mm
2
]
18. A 25 mm diameter rod of steel passes centrally through a copper tube 63 mm external diameter, 40 mm
internal diameter, and 1.30 m long. The tube is closed by rigid washers of negligible thickness and nuts
threaded on the rod. Find the stresses in each when the nuts are tightened until the tube is reduced in
length by 0.13 mm. Find the increase in the stresses if one nut is tightened by 1/2 of a turn relative to the
other, there being 0.4 threads per mm. Take E
s
= 200 GN/m
2
and E
c
= 100 GN/m
2
.
[Ans.
c
= 10 MN/m
2
(comp.),
s
= 37.9 MN/m
2
(tensile)
Increase in
c
= 33.2 MN/m
2
(comp.) Increase in
s
= 125.8 MN/m
2
(tensile)]
366 APPLIED MECHANICS
19. A steel rod 18 mm in diameter passes centrally through a steel tube 30 mm in external diameter and
2.5 mm thickness. The tube is 0.75 m long and is closed by rigid washers of negligible thickness which
are fastened by nuts threaded on the rod. The nuts are tightened until the compressive load on the tube
is 30 kN. Calculate the stresses in the tube and the rod.
[Ans.
st
= 90.15 MN/m
2
(Comp.) ;
sr
= 76.52 MN/m
2
(tensile)]
20. A compound bar consists of a central steel strip 25 mm wide and 6.4 mm thick placed between two strips
of brass each 25 mm wide and x mm thick. The strips are firmly fixed together to form a compound bar
of retangular section 25 mm wide and (2x + 6.4) mm thick. Determine :
(i) The thickness of the brass strips which will make the apparent modulus of elasticity of compound
bar 157 GN/m
2
.
(ii) The maximum axial pull the bar can then carry if the stress is not to exceed 157 MN/m
2
, in either the
brass or the steel. Take E
s
= 207 GN/m
2
and E
b
= 114 GN/m
2
.
[Ans. (i) x = 3.726 mm, (ii) 41.226 kN]
21. A weight of 50 kN is hanging from three wires of equal length, middle one is of steel and the other two
are of copper. If 300 mm
2
is the cross-sectional area of each wire, then find out the load shared by each.
Take E
s
= 210 GN/m
2
and E
b
= 120 GN/m
2
. [Ans.
c
= 13.6 kN,
s
= 22.8 kN]
Poissons Ratio :
22. A steel bar of rectangular cross-section 20 mm 10 mm is subjected to a pull of 20 kN in the direction of
its length. Taking E = 204 GN/m
2
and m = 10/3, find the percentage decrease of cross-section.
[Ans. 0.0294%]
23. A vertical circular bar 20 mm diameter, 3 m long carries a tensile load of 150 kN. Calculate :
(i) Elongation ; (ii) Decrease in diameter ; and
(iii) Volumetric strain. [Ans. (i) 15.9 mm, (ii) 0.0265 mm, (iii) 0.00265]
24. A steel bar 300 mm long, 50 mm wide and 12 mm thick is subjected to an axial pull of 84 kN. Find the
change in length, width, thickness and volume of the bar. Take E = 200 GN/m
2
and Poissons ratio = 0.32.
[Ans. l = 0.21 mm (increase),
b
= 0.0112 mm (decrease),
t = 0.0027 mm (decrease), V = 45.36 mm
3
(increase)]
Thermal Stresses and Strains :
25. A railway line is laid so that there is no stress in the rails at 60C. Calculate the stress in the rails at
20C, if
(i) no allowance is made for contraction ;
(ii) there is an allowance of 5 mm contraction per rail
The rails are 30 mm long. E = 210 GN/m
2
, = 0.000012 per C.
[Ans. (i) 100.8 MN/m
2
, (ii) 65.8 MN/m
2
]
26. A steel rod 30 mm diameter and 300 mm long is subjected to tensile force P acting axially. The temperature
of the rod is then raised through 80C and the total extension measured as 0.35 mm. Calculate the value
of P.
Take E
s
= 200 GN/m
2
and
s
= 12 10
6
per C. [Ans. 6.29 kN]
27. A steel bar is placed between two copper bars each having the same area and length as the steel bar at
15C. At this stage, they are rigidly connected together at both the ends. When the temperature is raised
to 315C, the length of the bars increases by 1.5 mm. Determine the original length and final stresses in
the bar.
Take E
s
= 210 GN/m
2
, E
c
= 110 GN/m
2
,
s
= 0.000012 per C,
c
= 0.0000175 per C.
[Ans. 0.34 m,
c
= 84.5 MN/m
2
(comp.),
s
= 169 MN/m
2
(tensile)]