This document consists of 8 printed pages.

SPA (MML 8112 3/04) S90517/1

UCLES 2005 [Turn over
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS
General Certificate of Education Ordinary Level
PHYSICS 5054/03
Paper 3 Practical Test
October/November 2005
CONFIDENTIAL INSTRUCTIONS
Great care should be taken that any confidential information given does not reach
the candidates either directly or indirectly.
Instructions for preparing apparatus
These instructions detail the apparatus required for each experiment in this paper. A summary of the
questions that will be presented to the candidates is included, to allow the Physics teacher to test the
apparatus appropriately. No access is permitted to the Question Paper in advance of the examination
session.
Number of sets of apparatus
In addition to a few spare sets, the minimum number of sets of apparatus to be provided should be
sufficient to enable candidates to spend 20 minutes with the apparatus for each of Questions 1, 2 and
3, and one hour with the apparatus for Question 4. The order in which candidates answer the
questions will be determined by the Supervisor. Candidates may spend one hour circulating around
Questions 1, 2 and 3, followed by an hour on Question 4, or vice versa.
Extra graph paper should be available. It is assumed that candidates will supply their own calculator
and geometrical instruments, such as a set square, 0 to 180 protractor, pair of compasses and
30 cm rule. Candidates should be advised in advance that they may, if they wish, use quartz
wristwatches with stopwatch facilities, providing that such wristwatches afford the required precision.
Instructions for the supervision of the examination
The Supervisor, who may be a Physics teacher, is responsible for the administration of the
examination according to the procedures detailed in the Handbook for Centres. In all instances, a
Physics teacher should be present. Preferably, this teacher should have been responsible for the
preparation of the apparatus. Two invigilators must be present at all times: it is not acceptable for a
teacher who has been responsible for preparing the candidates for this paper to be the sole
Supervisor or Invigilator.
Supervisors may make the following announcement at the start of the examination.
The Examiners do not want you to waste time when you are unable to do any experiment. Any
candidate who is unable to get results with an experiment may ask for help. The extent of this help will
be reported to the Examiners, who may make a deduction of marks.
Supervisors should note that a candidate may only be given enough assistance to allow some raw
readings or observations to be made. On no account should any assistance be given with the
treatment or analysis of these readings and observations.
Supervisors may draw to the attention of the candidates any significant deviation between the
apparatus provided and that detailed in the Question Paper, particularly where diagrams are given in
the paper.
Candidates should be reminded that all their work should be written on the printed Answer Booklet.
Rough paper must not be used.
The Supervisor must complete the Report at the back of these Instructions. Details should be given of
any significant deviation between the apparatus used and that specified in these Instructions. A
sample set of results can often help Examiners. A copy of this Report must be included in each
packet of scripts.
2
5054/03/INST/O/N/05
UCLES 2005
1 Items to be supplied by the Centre (per set of apparatus, unless otherwise specified)
Expendable steel spring of approximate length 3 cm and approximate diameter 1.5 cm e.g. Griffin
& George XBV-590-010H
30 cm rule
Two set squares
Access to a balance reading to at least 0.1 g
Procedure to be followed by candidates
Candidates will make measurements on the spring when the turns are touching.
Information required by examiners
Dimensions of the spring: unstretched length and diameter.
3
[Turn over
5054/03/INST/O/N/05
UCLES 2005
2 Items to be supplied by the Centre (per set of apparatus, unless otherwise specified)
Expendable steel spring of approximate length 3 cm and approximate diameter 1.5 cm e.g. Griffin
& George XBV-590-010H
Metre rule
Set square
Stand, boss and clamp from which the spring may be suspended
Second boss and clamp to hold the metre rule
A 500 g mass or five 100 g masses tied together
S hook, which may be constructed from a stiff piece of wire or by opening up a paper clip
Beaker containing water
Paper towels to mop up spillage
Notes
(i) The S hook should be attached to the 500 g mass by a length of thread so that the
candidates can suspend the mass from the spring. The length of thread should be such that
the 500 g mass can be completely immersed in the water in the beaker.
(ii) The beaker should be of sufficient diameter to ensure that the mass can easily fit into the
beaker. There should be sufficient water in the beaker to ensure that the mass can be fully
immersed without touching the sides or base of the beaker.
(iii) At the changeover, Supervisors should dismantle the apparatus. The mass should be placed
on a paper towel. Supervisors may also need to replenish the supply of water if the
candidate has spilled any.
Information required by examiners
None.
4
5054/03/INST/O/N/05
UCLES 2005
3 Items to be supplied by the Centre (per set of apparatus, unless otherwise specified)
6V d.c. power supply e.g. four 1.5 V cells in a cell pack
Switch or plug key (the question paper will refer to a switch)
Ammeter capable of reading up to 0.5 A to a precision of at least 0.01 A e.g. a 1.0 A full-scale
deflection analogue meter or a 2.0 A digital meter
Voltmeter capable of reading up to 6 V to a precision of at least 0.1 V e.g. a 10 V full-scale
deflection analogue meter or a 20 V digital meter
Nominal 47 resistor labelled X
Nominal 22 resistor labelled Y
8 connecting leads
Notes
(i) The resistors should have suitable terminations to enable them to be easily connected into
the remainder of the circuit. The values of the resistors should be obscured from the
candidates.
(ii) The Supervisor should set up the circuit as shown in the Fig. 3.1 with the resistor X in the
circuit. The switch should be open i.e. the circuit should not be complete.
(iii) At the changeover, Supervisors should remove the resistor Y from the circuit and ensure that
it is set up as shown in Fig. 3.1. Supervisors should check that any cells used in the circuit
have not run flat and that the switch is open.
Fig. 3.1
Information required by examiners
None.
A
V
X
5
[Turn over
5054/03/INST/O/N/05
UCLES 2005
4 Items to be supplied by the Centre (per set of apparatus, unless otherwise specified)
250 cm
3
Pyrex beaker
Supply of boiling water
10 C to 110 C thermometer
Stand, boss and clamp to hold the thermometer
Plastic stirrer
100 cm
3
measuring cylinder
Stopwatch
Paper towels to mop up spillages
Notes
(i) The supply of boiling water should be close to the apparatus being used by the candidates
so that candidates do not have to carry boiling water across the laboratory, e.g. an electric
kettle could be placed between two workstations. Candidates will have to transfer very hot
water to the beaker and Supervisors must ensure that this can be done safely.
(ii) The thermometer should be of sufficient length to enable candidates to interpolate between
1 C divisions, i.e. the thermometer should be between 20 cm and 30 cm long.
(iii) Supervisors should clamp the thermometer vertically with the bulb of the thermometer in the
beaker. The bulb of the thermometer should be just above the base of the beaker.
Supervisors should ensure that the clamp does not obscure the scale of the thermometer in
the region of 90 C to 50 C. The beaker should not be placed on the base of the stand,
because candidates will need to be able to lift the thermometer out of the beaker without
adjusting the clamp.
(iv) At the changeover, Supervisors should empty the beaker and the measuring cylinder, and
replace the thermometer in the beaker.
Procedure to be followed by candidates
Candidates will pour water from the supply into the beaker so that the bulb of the thermometer is
just covered.
Information required by examiners
None.
6
5054/03/INST/O/N/05
UCLES 2005
Permission to reproduce items where third-party owned material protected by copyright is included has been sought and cleared where possible. Every
reasonable effort has been made by the publisher (UCLES) to trace copyright holders, but if any items requiring clearance have unwittingly been included, the
publisher will be pleased to make amends at the earliest possible opportunity.
University of Cambridge International Examinations is part of the University of Cambridge Local Examinations Syndicate (UCLES), which is itself a department
of the University of Cambridge.
O
5054/3
This form must be completed and returned with the Answer Booklets.
REPORT ON PRACTICAL PHYSICS
The Supervisor is asked to give the following details, using the space provided on page 8.
(a) Information required at the end of the test, as indicated in the Instructions.
(b) Any help given to a candidate.
(c) Any general difficulties encountered in preparing the apparatus.
(d) Any difficulties experienced by particular candidates. These should include reference to
difficulties due to faulty apparatus or materials and accidental damage to apparatus or materials.
Candidates should be identified by name and candidate number.
Other cases of hardship, such as disability or illness, should be reported to CIE in the normal way.
The Supervisor is asked to provide a plan of the work benches, giving details by candidate numbers
of the places occupied by the candidates for each session. The plan should be enclosed with the
Answer Booklets, together with the Information required by Examiners.
Declaration to be signed by the Principal
The preparation of this practical examination has been carried out so as fully to maintain the security
of the examination.
Signed .......................................................................................
Name (in block capitals) .......................................................................................
Centre Number .......................................................................................
Centre Name .......................................................................................
7
[Turn over
5054/03/INST/O/N/05
UCLES 2005

Information required
Dimensions of the spring used in question 1:
unstretched length = ..........................................
diameter = .........................................................
Details of difficulties and any help given to candidates
8
5054/03/INST/O/N/05
UCLES 2005