Router Lab01

Lab 1
Lab 1: Two Router Basic Configuration

Objective: The objective of the lab is to configure a simple network to allow two routers to route packets between two remote networks.
1.1. Prelab
Read Chapter 4 The Network Layer from J. F. Kurose and K. W. Ross, Computer Networking: A Top-down Approach Featuring the Internet 3rd ed., New York: Pearson, 2005. ISBN 0-321-22735-2 Read the Router lab overview document. Locate the main web site that supports Auditor Security Collection and read about the available tools. Answer the questions for the prelab and turn them in. They must be turned in before doing the lab.
Page 1 of 9
Lab 1
1.2. Questions for Prelab

1. List the nine basic components of a Cisco router.
2.
What is the name of the second serial interface?
3.
What is the full name of the router operating system?
4.
Where is the configuration information saved in the router?
5.
Where is the operating system stored for PC1 and PC2?
6.
List the two disadvantages of using a live CD distribution.
7.
Why are the network interfaces turned off by default on PC1 and PC2?
8.
List three tools available on the Auditor Security Collection.
9.
What is the purpose of PC3?
10.
Name the command mode in the router used for configuration.
Page 2 of 9
Lab 1
1.3. Lab
Figure 1. Two router basic configuration
1.3.1. Objective
The objective of the lab is to configure a simple network to allow two routers to route packets between two remote networks.
1.3.2. Set up
1. Physical Verify the physical configuration shown in Figure 1. Connect PC3 to the console port of RouterA using the console cable. Verify that both PC1 and PC2 are connected via a cross-over (red) cable to the routers. Each PC should connect to one of the routers Ethernet transceivers. Verify that the serial cable is connected to the DCE port on RouterA and the DTE port on RouterB. Turn on the power strip. Turn on PC1, PC2, and PC3. Verify that the live CDs are in PC1 and PC2. Turn on both routers. 2. Login to RouterA Login to PC3 with the given userid and password. Start the terminal program KPP to access the serial port. o Click configure o Click device o Set to /dev/ttyS0, None, CR, 9600 o Click Modem
Page 3 of 9
Lab 1 o Click Terminal. It should now connect to the router console port. The command line interface RouterA> should appear.
1.3.3. Exercise
Configure RouterA and RouterB by typing the following commands. The console port cable will need to be moved to the router being configured. The part beginning with // are comments and should not be entered. Part 1. Configure RouterA and RouterB IP Addresses RouterA
RouterA>enable RouterA#config t RouterA(config)#int e0 //Choose Ethernet interface e0 RouterA(config-if)#ip address 172.16.12.1 255.255.255.0 RouterA(config-if)#description LAN Network for RouterA RouterA(config-if)#no shutdown //this means interface is up RouterA(config-if)#int s0 //configure serial interface RouterA(config-if)#ip address 172.16.10.1 255.255.255.0 RouterA(config-if)#clockrate 250000 RouterA(config-if)#no shutdown RouterA(config-if)#description Network connection to RouterB RouterA(config-if)#^Z //combination of control+z, which takes you back to the privileged executive mode RouterA# copy run start //Save your changes to NRVAM. If you do not, when the router reboots all changes are lost. Wait until the router responds with [Ok]
RouterB
RouterB#config t RouterB(config)#int e0 //Choose Ethernet interface e0 RouterB(config-if)#ip address 172.16.11.1 255.255.255.0 RouterB(config-if)#description LAN Network for RouterB RouterB(config-if)#no shutdown //this means interface is up RouterB(config-if)#int s1 //configure serial interface RouterB(config-if)#ip address 172.16.10.2 255.255.255.0 RouterB(config-if)#no shutdown RouterB(config-if)#description Network connection to RouterA RouterB(config-if)#^Z RouterB# copy run start
Part 2. Verify router configurations Once both routers are configured, use the ping command from a router to ping the neighboring routers serial and Ethernet interfaces.
RouterB#ping 172.16.10.1 RouterB#ping 172.16.12.1
Page 4 of 9
Lab 1
Verify the configuration on both routers using the following commands.

RouterA#show ip route RouterA#show ip int
Part 3. Configure PC1 and PC2 IP Addresses Manually configure the PC1 and PC2 IP addresses. PC1 Click on K in the lower left corner of the screen. Click Settings Click Netconfig Choose No. Type 172.16.12.2 as the IP address. Type 255.255.255.0 as the network mask. Type 172.16.12.1 for the default gateway. Use the default 127.0.0.1 for the DNS. Click Exit. Start a terminal and do the following commands. Note and log what happens at each point. o #ping 172.16.12.1 o #ping 172.16.10.1 o #ping 172.16.10.2 o #ping 172.16.11.1
PC2 Repeat the steps for PC2 but set the IP address to 172.16.11.2 and the default gateway to 172.16.11.1. Start a terminal and do the following commands. Note and log what happens at each point. o #ping 172.16.11.1 o #ping 172.16.10.2 o #ping 172.16.10.1 o #ping 172.16.12.1 o #ping 172.16.12.2 Explain why some interfaces can be pinged and others cannot.
Page 5 of 9
Lab 1
Part 4. Adding dynamic routing: RIP A routing protocol like RIP needs to be enabled on the routers to advertise the directly connected networks to the neighboring router. RouterA
RouterA>en RouterA#config t RouterA#ip routing //enable routing RouterA(config)#router RIP //enable the routing information protocol RouterA(config-router)#network 172.16.12.0 RouterA(config-router)#^Z RouterA#copy run start
RouterB Enable RIP on RouterB but advertise 172.16.11.0. Part 5. Verify the two routers are routing packets to the remote network Use PC1 and PC2 to verify that the two remote networks can communicate. PC1
#ping 172.16.11.2
PC2
#ping 172.16.12.2
If both ping commands work, then the configuration is complete. Two remote networks are communicating through two routers. Congratulations!
Page 6 of 9
Lab 1
1.4. Checklist
Complete this checklist as the lab is performed and attach it to the lab report. Name: _______________________________________________________
1. Turn in questions for prelab 2. Exercise Part 2 3. Exercise Part 3 4. Exercise Part 5 5. Complete Feedback sheet 6. Notify instructor 7. Lab report
_____ _____ _____ _____ _____ _____ _____
Page 7 of 9
Lab 1
1.5. Feedback
Complete this form after completing the lab exercises and turn it in with the lab report. Do not put your name on the form and keep it separate from the lab report.
Difficulty: (1-10): 1 is too easy and 10 is too hard. Interest level: (1-10): 1 is low interest and 10 is high interest Difficulty Set up Exercise What did you like about this lab? Interest Level Time to complete (minutes)
What did you dislike about this lab?
Make a suggestion on how to improve the lab.
Page 8 of 9
Lab 1
1.6. Lab Report

In the lab report, answer the following questions. Why was the default gateway set for PC1 and PC2? Why was RIP needed for PC1 and PC2 to communicate? How does RIP work?
Page 9 of 9

Router Lab01

Uploaded by

Copyright:

Available Formats

Router Lab01

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Router Lab01

Uploaded by

Copyright:

Available Formats

Lab 1

Lab 1: Two Router Basic Configuration

1.2. Questions for Prelab

What is the name of the second serial interface?

What is the full name of the router operating system?

Where is the configuration information saved in the router?

Where is the operating system stored for PC1 and PC2?

List the two disadvantages of using a live CD distribution.

List three tools available on the Auditor Security Collection.

What is the purpose of PC3?

Name the command mode in the router used for configuration.

Figure 1. Two router basic configuration

Verify the configuration on both routers using the following commands.

___ _ _ _ _ _ ___

What did you dislike about this lab?

Make a suggestion on how to improve the lab.

1.6. Lab Report

You might also like