WARNING

The WARNING

TO THE USERS OF SYNTHETIC PRODUCTS

Icon, used in our product information is done to alert sling users to potentially hazardous conditions and situations.

WARNING It is your explicit responsibility to consider all risk factors prior to using any rigging device or product. Read and understand the information contained in this bulletin, in our catalog, on our web site www.lift-it.com and follow OSHA and ASME guidelines. Use by untrained persons is hazardous. The American Society of Mechanical Engineers, in the Sling Safety Standard, ASME B30.9-2003, clearly establishes the requirement for training. Sections 9-5.1 and 9-6.1-Training states, Synthetic webbing and round sling users shall be trained in the selection, inspection, cautions to personnel, effects of the environment and rigging practices, covered by this chapter. WARNING All Products supplied and manufactured by Lift-It Manufacturing are sold with express understanding that the purchaser and user are thoroughly familiar with the safe and proper use and application of the product. The qualified person and sling user has the responsibility for use and application, and should have sufficient training and knowledge of all applicable standards to responsibly use our products. WARNING Failure to follow proper use, care and inspection criteria could result in severe personal injury or death. Synthetic products will fail if damaged, abused, misused, overused, or improperly maintained.

WHEN ORDERING OR USING, ALWAYS CONSIDER:

Type of hitch Chemical Environment Sling-to-Load angle Adequate wear protection

Sling Hitches
Slings carry their loads in one of three primary hitches. The work load limit of the sling is affected by the hitch that is used. Most slings can be used in all three hitches, but some slings are designed for use in only one hitch. Slings have the largest work load limit when used in a basket hitch. The work load limit of a vertical hitch is 50% of the basket hitch. The same sling would be assigned a different work load limit for the choker hitch. The choker work load limit is a maximum of 80% of the vertical work load limit per ASME recommendation.

CHOKER HITCH
Sling passes through one eye around the load. The other eye is free to be placed on the hook.

VERTICAL HITCH
One eye is on the hook, while the other eye is attached directly to the load. Use a tagline to prevent load rotation.

BASKET HITCH
The sling cradles the load while both eyes are attached overhead.

Chemical Considerations
It is important to select a sling that has the proper chemical characteristics, making the sling compatible with its environment.

PERFORMANCE CHARACTERISTICS OF SYNTHETIC FIBERS

POLYESTER Polyester is not significantly affected by most compounds of the following classes: alcohols, dry cleaning solvents, halogenated hydrocarbons, ketones, soaps and synthetic detergents or water (including sea water). Polyester also has good to excellent resistance to aqueous solutions of most weak acids at the boil and to most acids at room temperature, but is disintegrated by concentrated sulfuric acid (95%) at room temperature. Polyester products also have good resistance to most aqueous solutions or strong alkalis at room temperature, but are degraded by the same solution at the boil. Oxidizing agents and bleaching treatments ordinarily used by the textile industry also do not degrade polyester fiber. Stretch at work load limit is approximately 3-4% and polyester does not lose strength as a result of moisture absorption. The acceptable temperature exposure range is -40F (-40C) to a maximum of 194F (90C). ARAMID Aramid fibers are resistant to most weak acids, alkalis, ketones, alcohols, hydrocarbons, oils and dry cleaning solvents. Strong acids and bases and sodium hypo-chlorite bleach attack Aramid fibers, particularly at elevated temperatures of high concentrations. Stretch at work load limit is approximately 1%. K-SPEC K-Spec fibers are a specialty high performance combination of High Molecular Polyethylene and Aramid fibers. Chemical and performance characteristics are those of the primary fibers, Aramid and High Molecular Polyethylene. Stretch at work load limit is approximately 1% and the acceptable temperature exposure range is -40F (-40C) to a maximum of 194F (90C). HIGH MOLECULAR POLYETHYLENE Resists many chemical agents and retained 100% of the original fiber strength when immersed for 6 months in the following: 1M Hydrochloric acid Gasoline Sea water 5M Sodium Hydroxide Toluene 10% detergent solution Perchloroethylene Kerosene Hydraulic fluid Glacial acetic acid Hypophosphite solution (10%) Ammonium Hydroxide (29%) Clorox degraded High Molecular Polyethylene Fiber by approximately 10% after a 6 month immersion test. Stretch at work load limit is approximately 1% and maximum temperature exposure is 140F (60C). NOMEX Nomex is resistant to most ketones, alcohols, dry cleaning solvents and many other organic solvents. Its acid resistance is superior to that of nylon, but is not as good as that of polyester. Nomex shows good resistance to alkalis at room temperature, but is degraded by strong alkalis at higher temperatures. Nomex is compatible with fluorine-containing elastomers, resins and refrigerants at high temperatures and is resistant to fluorine compounds in concentrations usually encountered in stack gases from metallurgical and rock-processing operations. The resistance of Nomex to oxides of sulfur at temperatures above the acid dew point is su00perior to that of polyester. Below the dew point, concentrated sulfuric acid may condense on the fiber and cause a progressive loss in strength.
WARNING Our Products may contain chemicals known to cause cancer, birth defects and/or other reproductive harm.

Sling-To-Load Angle
Slings with adequate work load limits to handle the scale weight of the load have catastrophically failed because of an inadequate consideration of the sling angle and the increased tension. Any load rigged in a hitch that is not vertical, develops increased tension on the sling. When selecting a sling, always consider the sling to load angle (horizontal angle) and the tension that will be applied to the sling. Whenever a choker Hitch results in an angle of choke that is less than 120 degrees, the work load limit must be adjusted. Simply multiply the choke hitch work load limit by the appropriate loss factor to determine the slings actual work load limit.

SLING-TO-LOAD ANGLE

The horizontal angle formed between the sling leg and the top of the load.

Angle of choke

ILLUSTRATED ABOVE- INCREASED LOAD STRESS IS MAGNIFIED BY ANY CHANGE FROM VERTICAL TOWARD HORIZONTAL LIFTING. THE SAME STRESS IS IMPOSED UPON SLING LEGS ATTACHED TO THE LOAD AT VARIOUS ANGLES.
A BASKET WORK LOAD LIMIT OF 10,000 LBS. CHANGES AS THE SLING-TO-LOAD ANGLE CHANGES: AT 90- WORK LOAD LIMIT = 10,000 LBS. AT 60 - WORK LOAD LIMIT = 8,660 LBS. AT 45 - WORK LOAD LIMIT = 7,071 LBS. AT 30 - WORK LOAD LIMIT = 5,000 LBS.

SLING ANGLES OF LESS THAN 45 DEGREES SHOULD NOT BE USED, UNLESS APPROVED BY A QUALIFIED PERSON.

Wear Protection
Synthetic slings can be damaged, abraded or cut as tension and compression between the sling, the connection points and the load develops. Edges and abrasive surfaces in contact with the sling must be padded with materials of sufficient strength and/or thickness to prevent damage and catastrophic sling failure. The edge of the load need not be razor sharp to damage the sling. A combination of non-positive sling to load contact (sling slipping across the load) and inadequate wear protection materials may result in wear protection damage and sling failure. The result is uncontrolled load descent. Wear protection may not prevent cutting or other forms of sling damage. Personnel should never be under or on the load, while the lift is in progress. WARNING Cut proof wear protection does not exist. Materials must be evaluated and selected based upon the application and type of exposure. Some materials are suitable for abrasion resistance, but offer virtually no protection against the effects of cutting. Twin-Path Extra, High Performance Fiber Slings can develop a 25,000 pound per inch of width, work load limit. A web sling can develop a 12,800 pound per inch of width, work load limit. Certain materials used in the construction of wear protection and protectors have been evaluated for cut resistance. Magnetic corner protectors, Cornermax and Meshguard wear protectors have been evaluated and are rated for cut resistance, exceeding the 12,800 pounds per inch loading requirement.

WARNING SLEEVES

Materials of sufficient strength and resistance to damage must be employed to prevent injury, death and/or property damage.

MAGNETIC CORNER PROTECTOR

Magnetic corner protectors are fabricated from a durable synthetic material that protects synthetic and wire rope slings from damage. They work on any 90 degree cornered load and keep the sling from contacting the load.

Sleeves cover both sides of the sling and can be shifted to a specific location. The sleeve can also be re-positioned for quick and easy inspection of the sling. Available in six different materials: Cordura, Heavy Duty Nylon, Leather, Neoprene, Felt and Aramid. Available in sewn edge, tubular and quicksleeve constructions.
ORDER CODE DESIGNATIONS MATERIAL CORDURA WEB CHAP 1/8" CHAP 1/4" FELT 1/8" FELT 1/4" FELT 3/8"

CONSTRUCTION SEWN QUICK TUBULAR Lift-It wear protection is constructed from the following: CS CQS CQTS WS WQS WQTS CHS 125 CHQS 125 CHQTS 125 CHS 250 CHQS 250 CHQTS 250 FS 125 FQS 125 FQTS 125 FS 250 FQS 250 FQTS 250 FS 380 FQS 380 FQTS 380

WEAR PROTECTION INFORMATION

Magnetic corner protectors are protection rated at 12,500 PSI. Available in 9, 12 and 18 inch lengths. Application temperatures range from -20F( -29C) to 220F (104C) . Heavy duty protectors, featuring larger diameters are also available. The magnets are designed to keep the protector from WARNING falling from metallic loads and are not intended to prevent the protector or sling from sliding. Slings and protectors should be vertical or perpendicular to the load. The farther from vertical that the slings and protectors are, the more likely the protectors and slings will slide to become vertical and result in load instability and uncontrolled load descent. When using magnetic corner protectors always inspect for damage, prior to use. Keep magnets clean and free of debris.

CORNERMAX
Cornermax wear protection is truly remarkable because its design forms a tunnel between the load edge and the wear pad. This barrier greatly reduces the possibility of cutting. WARNING
A tunnel is formed between the Cornermax wear pad and load edge

MESH GUARD
Lift-It Mesh guard features a unique combination of wear protection materials. A layer of felt buffers the sling, while carbon steel wire mesh covers the load edge.
TUBULAR CORDURA

HOOK & LOOP CLOSURE BANDS

No form of wear protection is cut proof.

CORNERMAX PART NUMBER CM-6 CM-8 CM-10 CM-12 CM-14 SLING WIDTH (INCHES) 1 - 2 IN. UP TO 5 IN. UP TO 6 IN. UP TO 8 IN. UP TO 12IN. CORNERMAX PROTECTION RATING WIDTH (LBS) (INCHES) 6 8 10 12 14 25,000 60,000 100,000 100,000 100,000

WIREMESH

Hook and loop closure bands make attachment and removal quick and easy.

3/8 THICK FELT

CHAP SLEEVES
Lift-It Chap Sleeves blend two wear protection materials: Polyester Felt, covered by Tubular Cordura. Chap Sleeves provide protection from abrasion damage, caused by contact with rough surfaces. Quick Chaps are available with hook and loop tape, making installation and removal, quick and easy. Please specify sleeve width and length.
Chap Sleeve Quick-Chap

SHACKLE PIN PROTECTOR PADS

ARAMID FELT

ARAMID FELT

If you must rig on the pin, protect your sling with a shackle pin protector pad. * Full length protection, including the ear seams. * Three connection points secure pad to shackle * Installation and removal in seconds.

Design Features
EASY TO INSPECT
The Twin-Path sling design provides the sling user with an early warning and inspection system. The load carrying yarns never come into contact with the load. The Twin-Path sling design features two independent covers that are contrasting in color for easy inspection. When the protective outer cover is damaged, the inner red cover becomes visible providing the sling user with a visual alert to remove the sling from service and return to the manufacturer for repair evaluation.

TATTLE TAILS - (U.S. Patent No. 5,651,572)

Before each use, inspect the entire sling. Tattle Tails are not a precision force measurement device, or a dynamometer. The tattle tail is an extension of the internal yarn bundle. Tattle Tails will retract and eventually disappear as the sling is overloaded. Tattle Tails should extend past the tag area of the sling. If both tattle tails are not visible, remove the sling from service. If the tattle tails or any part of the sling shows evidence of chemical degradation, remove it from service and return to the manufacturer for repair evaluation.

FIBER-OPTIC INSPECTION - (U.S. Patent No. 5,651,572 and Patents Pending)

Fiber-optic inspection cables assist the sling user and inspector to evaluate the condition of the load carrying yarns. The condition of the internal load carrying yarn can be inspected by checking the conductivity of the fiber optic cable. If the load carrying yarns have suffered chemical, heat or crushing damage, the fiber optic cable will loose its ability to transmit light from one end to the other, giving the inspector a reason to remove the sling from service and return it for repair evaluation. The fiber optic cable will conduct light from natural, overhead or flashlight sources. FAST INSPECTION SYSTEM The Fast Inspection System provides subjective, not objective pass/fail criteria for Twin-Path and roundslings of different constructions, types and materials. The Fast Inspection System, combined with thorough visual and tactile inspection techniques, provides the sling user and inspector with an effective inspection system. The Fast Inspection System provides a warning to sling users and inspectors of internal load carrying fiber damage from fiber on fiber abrasion or overloading beyond twice the vertical work load limit. If the sling is loaded beyond the work load limit, the External Warning Indicator will disappear before the sling fails. If the sling passes a visual and tactile inspection, the Fast Ribbon cannot be pulled easily from the sling and the Early Warning Indicator are visible, the sling may be used.

Fiber-Optic Cable

Sling Inspection
TWIN-PATH INSPECTION SYSTEM
INITIAL INSPECTION - Before any Twin-Path is placed into service it shall be inspected by a designated person to ensure that the correct sling is being used, as well as to determine that the TwinPath meets the requirements of the specifications contained in this publication, and to all applicable requirements. The sling shall also be inspected to ensure that no damage occurred during transit. The sling(s) must also be verified to be correct, as ordered and that they comply with the manufacturers specifications. Without printed product specifications this comparison cannot be accomplished. If written records for individual slings are to be maintained, the specific sling information should be initiated at this level of inspection. FREQUENT INSPECTION - This inspection shall be made by a qualified person handling the Twin-Path before each use. Proper sling selection, hazard recognition and removal from service shall also be accessed by the sling user or competent person. Written inspections are not required for frequent inspections. PERIODIC INSPECTION - This inspection shall be conducted by a designated person. Frequency of inspection should be based on: Frequency of use, severity of the service conditions, experience gained on the service life of Twin Path Slings used in similar applications. Periodic inspection intervals shall not exceed one year intervals. ASME states that guidelines for the inspection time intervals are as follows: Normal Service- Yearly Severe Service---Monthly or Quarterly Special Service--As recommended by a qualified person Written records of the most recent periodic inspection shall be maintained for each lot of slings and shall include their condition. Records and documentation should be kept in the safety office or at the specific sling storage area.

REMOVAL FROM SERVICE CRITERIA

Slings shall be inspected throughout their entire length for evidence of damage. Core integrity is determined by a hand over hand inspection of the entire sling, combined with a thorough visual inspection.
Twin-Path Slings shall be removed from service if any of the following is visible: A) Missing or illegible work load limit tags B) Brittle or stiff areas that may indicate chemical damage, acid or alkali burns. C) Melting, charring or weld spatter of any part of the sling. D) Holes, tears, cuts, embedded particles, abrasive wear, or snags that expose the load carrying yarns. E) Broken, cut or damaged load carrying yarns. F) Broken or worn stitching in the cover which expose the load carrying yarns. G) Fitting distortion: elongated, damaged, corroded or chemical degradation of fittings or component hardware. H) Slings that are knotted. I) Tattle tails - if one or both of the tattle tails is not visible or is chemically degraded. J) Fiber-Optic - Lack of fiber optic light transfer, in sling models with the fiber optic (FO) option. K) For slings equipped with Fast Inspection: External Warning Indicator (EWI) is not visible The Fast Ribbon pulls out of the sling cover L) For hooks, removal criteria as stated in ASME B30.10 M) For applicable fittings, removal criteria as stated in ASME B30.26 N) Other damage which causes any doubt as to the strength of the sling.

WARNING Tattle Tails, Fiber Optics and/or the Fast inspection system can not be used exclusively to determine the condition of the load carrying fibers or sling. These patented, inspection devices must be used in conjunction with visual and tactile inspection techniques to determine sling condition. If there is any doubt, do not use this or any other rigging product. Return the sling to the manufacturer for factory repair evaluation.

WARNING
CUT OR DAMAGED YARNS

IF ANY DAMAGE SUCH AS THE FOLLOWING, IS VISIBLE, THE SLING SHALL BE REMOVED FROM SERVICE IMMEDIATELY.

SNAGS / PUNCTURES

CHEMICAL DAMAGE

KNOTS

BUNCHED OR WADDED YARNS

FIBER OPTIC

EWI IS MISSING
Fast RIBBON PULLS OUT

TATTLE TAILS
NOT VISIBLE

INNER CORE OR YARN VISIBILITY

WELD SPLATTER

Twin- Path Considerations

EXPOSURE TEMPERATURE: Twin-Path slings with polyester load carrying fibers, and Twin-Path Extra slings with K-Spec High Performance load carrying yarns should not be exposed to temperatures above 194F (90C). or below -40F (-40C). Twin-Path Sparkeater slings should not be exposed to temperatures above 300F (149C). COLD WEATHER EXPOSURE: Twin-Path Extra slings with K-Spec High Performance load carrying yarns become stronger at - 50F and have been used successfully in Northern Canada and Alaska for many years, without incident. The same yarn components that make up K-Spec load carrying yarn are also used in deep space exploration applications. Twin-Path Extra slings with K-Spec High Performance load carrying yarns are a viable alternative for cold weather applications. TATTLE TAILS: Twin-Path Extra slings have been extensively used and tested in all possible hitch configurations. The tattle tails performed as expected. If the sling is used as a load manipulator, i.e., used to turn or rotate a load, the tattle tales will malfunction. This is a direct result of the differences in the coefficient of friction, developed between the sling cover and the manipulated object and the coefficient of friction developed between the load carrying yarns and the internal sling jacket. Simply stated, the cover binds to the load, while the load carrying yarns rotate within the sling cover. LOAD MANIPULATION: When Twin-Path Slings are used to change the orientation of an object, from the vertical to the horizontal, or visa versa, the cross over point on the sling paths, becomes a hinge point for this action. The Covermax cover will become damaged at the cross over point. If load carrying yarns are visible, return the sling for a factory repair evaluation and do not continue to use the sling. PATH ORIENTATION: Twin-Path Slings feature two independent paths that must be kept side by side. Folding one path on top of the other path, to fit into a small area, results in differential path lengths. The top path will see more tension than the lower path. The result is the sling work load limit is reduced by 50%. RADIATION EXPOSURE - Information on the properties of aramid fiber performance in nuclear environments is detailed in a report titled, Radiation Effects on Organic Materials in Nuclear Power Plants EPRI Report NP 2129, dated November 1981. When aramid fibers were exposed to radiation at a level of 1,000,000,000 rads, there was no effect on the performance characteristics of the fiber. COMPONENT HARDWARE - When synthetic slings are used with a shackle, it is recommended that they be rigged in the bow of the shackle and not on the pin. The pin of the shackle can damage synthetic slings, resulting in sling failure. Placing the sling on the shackle pin should be avoided, unless the sling is protected. Crane manufacturers are using smaller, stronger crane hooks, produced from improved alloys. Twin-Path slings forced into a hook or fitting may incur damage at the connection point. The relationship must be proper to ensure that the sling will seat properly and derive the greatest strength and longevity. TESTING - Proof testing is mandatory for every newly manufactured and repaired Twin-Path sling. The sling is pulled to twice the work load limit and held for a minimum of 15 seconds. Our proof test machine is certified annually to meet or exceed the standards as described in ASTM-E4 or other equivalent standards. TREMENDOUS SAVINGS - Time is money and the ease of handling ultra-light Twin-Path Extra Slings adds up to substantial, cumulative savings. A TUFXKS 7000 x 35 ft. weighs a mere 60 lbs. and is rated at a basket work load of 140,000 lbs. A wire rope sling of equal length and strength weighs 588 lbs. Extra cranes, forklifts, transport vehicles and personnel are no longer required. Twin-Path Extra Slings have documented savings and prove to be the least expensive sling you can buy. USER FRIENDLY - Twin-Path Extra Slings are easy to handle and will not choke lock, deterring the removal of the sling from the load. Lightweight Twin-Path Extra Slings help eliminate back, hand, foot and head injuries that occur when handling heavy, awkward, cumbersome wire rope and chain slings. LOAD FRIENDLY - Twin-Path Slings provide load protection through a wide bearing surface, that contacts the load. Twin-Path Slings will not mar, scratch or deface the most delicate metallic surface and are equally gentle on non-metallic loads. LOW ELONGATION - A Twin-Path Extra Sling (TUFXKS 11000 x 328 in.), with High Performance, K-Spec fibers was vertically proof tested to 220,000 lbs. After a ten minute period, a total elongation of 2 inches was recorded. Low elongation extends sling longevity, when stretch in the load contact areas is minimized. PULLING AND TOWING - Destruction testing demonstrates that Twin-Path Extra Slings, featuring K-Spec High Performance yarn recoils very little at break. High modulus, low stretch materials eliminate most of the devastating whiplash effects, characteristic of chain, wire rope, and web slings. WARNING Never stand near or in line with a sling, under tension.

SUPERIOR ABRASION RESISTANCE - Twin-Path Slings feature polyester or Covermax covers. The seamless covers are specifically woven to provide abrasion resistance. Covermax is approximately four times more abrasion resistant than polyester covers. MATCHED SLING LENGTHS - Twin-Path slings can be made in matched lengths, to unbelievable tolerances, on a consistent basis. The accuracy of our products is unparalleled. SPACE SAVER - Storage problems are easily resolved as Twin-Path Extra Slings require substantially less space than the bulky, cumbersome wire rope and chain slings. ENVIRONMENTALLY SENSITIVE - Twin-Path Slings do not require lubrication and will not corrode, rot or mildew, thereby eliminating the harmful release of chemical agents or by-products. Twin-Path slings are more resistant to UV degradation than unprotected slings, as the outer covers protect and shield the load carrying fibers. Twin-Path Slings do not loose strength when wet. CYCLE TESTING - Cyclic, vertical, fatigue testing was performed on Twin-Path Extra slings with K-Spec High Performance yarn. The independent test facility confirmed an 85 % retention of the original tensile strength after 50,000 cycles to 150% of work load. Twin-Path Extra Slings with Covermax covers will outlast and outperform synthetic and wire rope slings. REPAIRABILITY -The abrasion resistance of K-Spec, High Performance yarn facilitates repair to the protective outer covers, when the load carrying yarns are not damaged. Slings that appear to be extremely distressed have been successfully repaired for a fraction of the original price. Trained, factory professionals carefully inspect every area of damage. If the yarn is undamaged, the cover is repaired and the sling is proof tested to 200% of the work load. When abrasion resistance and longevity are considerations, and when only the best is good enough, choose Twin-Path Extra slings with the Covermax. CREEP - Twin-Path Extra High Performance Fiber Slings with K-Spec fiber does not vary in length with usage. Creep is defined as non-recoverable stretch. Other sling designs and materials creep. Sling users generally add shackles to equalize sling length for a level load. Spend less money on on heavy metal shackles by specifying, Twin-Path Extra Slings with K-Spec Fiber, a Slingmax solution sling.

Mechanical and Operational Considerations

Select the sling having the most suitable characteristics for the type of load, hitch and environment. Determine that the weight of the load is within the work load limit of the sling. Slings shall not be loaded in excess of the work load limits. Consideration should be given to the angle of lift, (sling-to-load angle) which affects the work load limit of the sling. Diameters of pins and load contact edges also may affect the work load limit of the sling. Synthetic products stretch when the load is applied. Stretching can be reduced by using slings with larger work load limits or by selecting a low elongation, High Performance Fiber, Twin-Path Sling.

WARNING Do not exceed work load limits. You are cautioned that all published work load limits and break strengths apply to only new and unused slings, assemblies and hardware. Work load limits are based upon: material strength, design factor, type of hitch, angle of loading, the diameter and curvature that the sling contacts, and destruction testing done in laboratory controlled, testing conditions, which will never be duplicated during actual usage. Working Load limits are also based on a moderately dynamic lifting or pulling operation. Instantaneous changes (drops or sudden pick ups) in excess of 10% of the work load constitute hazardous shock loading and THE WORKING LOAD LIMITS AS STATED, DO NOT APPLY.
Do not accelerate or de-accelerate the load too fast. The G force on a 1000 lbs. load dropped 3 feet could surpass the ultimate strength of the sling. A load picked up too fast can develop a stretch/friction/surface heat that will surpass the melting temperature of the sling. Working load limits for Multi-Leg Bridle Assemblies are based on the following conditions: 1. Even load weight distribution on all legs. 2. The bridle legs being same length. If the legs are not sharing the load equally, the assembly design factor is reduced. 3. All bridle legs used at the same horizontal angle. If the conditions of the lift vary from those above, the work load limit must be recalculated. Never use Twin-Path Adjustable Bridles in situations where the sling-to-load angle is less than 45, unless approved by a competent person. Always connect above the center of gravity. If connections are made below the center of gravity, the load may turn when lifted. The sling shall be securely attached to the load and rigged in a manner to provide for load control. The sling must be rigged to prevent slipping and sliding along the load edge. Slings skipping through hardware components in the sling system can become damaged. Balancing and controlling the load is critical and necessary to prevent sling damage and failure. Multiple factors must be taken into consideration to ensure that load control and stability are attained. A load with a high center of gravity can rotate in certain sling hitches.

WARNING Polyester Fibers are adversely affected by aldehydes, ethers, concentrated sulfuric acid and alkalis at elevated temperatures. Nylon fiber is adversely affected by acids and bleaching agents. Some Twin-Path slings feature a bulked nylon, Covermax cover and polyester load carrying yarns. In active chemical environments, where a combination of chemicals could be deleterious to either or both yarn types, the sling user or competent person must make a hazard assessment. WARNING Aluminum Hardware is severely degraded by alkali, caustic and acidic environments. Salt water also degrades aluminum. Aluminum hardware should never be exposed to chlorine environments or cleaned with chlorine based solutions. Steel hardware is not impervious to these elements. Chemical and environmental compatability must be assessed and suitability determined by the user. Avoid contact of hardware with load edges. WARNING The hook latch is designed to retain slings under slack conditions. The hook latch is not intended to support the load.
Caution: The use of G Links on larger stock diameters than recommended may lower the design factor.

WARNING

WARNING Placing synthetic slings on the shackle pin should be avoided. Even a new shackle can have damaging, exposed threads. If the synthetic sling contacts this area, it can be cut and fail catastrophically. If you must rig on the pin, protect your sling with a shackle pin protector pad. WARNING The use of improper fittings and/or materials may result in severe personal injury or death.
Synthetic slings shall not be constricted or bunched between the ears of a clevis or shackle, or in a hook. All hooks, shackles and other fittings must be free of edges and surfaces that could damage the sling. All loads applied to the lifting hook should be centered in the bowl of the hook to prevent point loading The opening in the fitting should be one of the proper shape and size to ensure that the fitting will seat properly in the lifting hook or other points of attachment. The fittings used in a sling system must be of the proper shape, size and diameter to prevent damage to the sling. The sling-fitting relationship must be proper to ensure that the sling will seat properly and, in doing so, derive the greatest work load limit. Attached sling hardware may be returned to the manufacturer for possible reuse. It must be tested to twice the work load limit. Slings shall not be dragged on the ground, floor or over abrasive surfaces.
Slings shall not be pulled from under loads when the load is resting on the sling.

WARNING

WARNING

Sling legs should contain or support the load from the sides above the center of gravity when using a basket hitch. Load edges in contact with the sling must be padded with materials of sufficient thickness or strength to prevent sling damage. The protection must be installed and evaluated for suitability by raising the load, slightly and then lowering the load for an inspection of the sling and the protection devices. Several test lifts may be necessary to determine the proper form of protection for a successful lift.

Loads resting on the sling could damage the sling. If feasible, place blocks under the load prior to setting down the load to allow removal of the sling. Synthetic slings should never be used to pull an object in a snagged or constrained condition. Synthetic slings are designed to stretch; the recoil caused by any sudden release of a lifting constraint could result in a dangerous projection of the load.
During the lift, with or without load, personnel shall be alert for possible snagging.

WARNING Wear protection may not prevent cutting or other forms of sling damage. To avoid severe personal injury or death, personnel should be kept away from the load and never be under or near the load, while it is being lifted or suspended. Never stand near or in line with a sling, under tension.
Synthetic slings shall not be shortened, lengthened, tied in knots, or joined by knotting. Twisting and kinking the sling legs shall be avoided.

Do not drop objects on slings or slings equipped with metal fittings. Do not run over slings with trucks or other equipment. Slings used in a choker hitch must be of adequate length for the choke action to occur on the sling body. The choke action should not occur on the fitting, at the base of the fitting or the sling tag. Slings used in a choker hitch shall not be forced to tighten around the load by pounding with hammers or other objects. Choker hitches are the least efficient way to use a sling based on work load limit. Two slings should be used to balance the load. One sling used in a choker hitch may result in a situation where an unbalanced load could lead to an accident. A sling rigged in a choke hitch (not double wrapped) does not make full contact with the load. Use multiple slings, and wrap the load, when practical to ensure full contact. Do not allow the slings to cross over each other. Always refer to the sling tag to determine the sling work load limit. Keep the sling tags and labels away from the load, the hook and the choke action of the sling. The sling tag should be maintained and kept legible during the life cycle of the sling by the sling user. Personnel should stand clear of the load and shall not ride the load. Personnel should never be under, or on a live or suspended load. Portions of the human body shall not be placed between the sling and load or between the sling and lifting hook.
Synthetic slings shall not be used as bridles on suspended personnel platforms.

WARNING Steam cleaning at temperatures in excess of 194 degrees F (90 degrees C) can damage the sling. Power or pressure washing can force residue inside web and yarn fibers. The foreign material can cause internal yarn and fiber damage.

Environmental Considerations
TEMPERATURE Conventional synthetic products should never be used at temperatures in excess of 194F (90C). Cold temperature exposure to 40F/(-40C) does not affect the strength of the synthetic sling. Temperature exposure outside the acceptable range must be considered and evaluated by the user. STORAGE When not in use, store slings in a cool, dry, dark location, free of mechanical and environmental damage. The storage location should be ventilated and not exposed to heat sources, weld splatter, or grit and splinters from grinding. FOREIGN MATERIAL Metal chips, weld splatter or heavy grit can damage a sling both externally and internally. CHEMICAL Chemically active environments can affect the strength of synthetic products in varying degrees ranging from moderate to total degradation. Before slings are used, the chemical compatibility between the sling components and the environment must be considered. Consult the sling manufacturer before purchasing to insure the synthetic products are chemically compatible with the environment. SALT WATER Slings that have been exposed to saltwater should be thoroughly rinsed and allowed to dry, preferably out of direct sunlight.

WARNING

TO THE USER OF SYNTHETIC SLINGS

WARNING Failure to follow proper use, care and inspection criteria could result in severe personal injury or death. Synthetic products will fail if damaged, abused, misused, overused, or improperly maintained. WARNING It is your explicit responsibility to consider all risk factors prior to using any rigging device or product. Read and understand the information contained in this bulletin, in our catalog, on our web site www.lift-it.com and follow OSHA and ASME guidelines. Use by untrained persons is hazardous.

The American Society of Mechanical Engineers, in the Sling Safety Standard, ASME B30.9-2003, clearly establishes the requirement for training. Sections 9-5.1 and 9-6.1-Training states, Synthetic webbing and round sling users shall be trained in the selection, inspection, cautions to personnel, effects of the environment and rigging practices, covered by this chapter.
WARNING All Products supplied and manufactured by Lift-It Manufacturing are sold with express understanding that the purchaser and user are thoroughly familiar with the safe and proper use and application of the product. The qualified person and sling user has the responsibility for use and application, and should have sufficient training and knowledge of all applicable standards to responsibly use our products.

ACCIDENT PREVENTION THROUGH EDUCATION

If you are not trained in the use of synthetic lifting slings, you and your employer should consider the Lift-It Sling Safety Program. The benefits of educating synthetic sling users, prior to death or injury, clearly outweigh any effort done in reaction to a liability incident. The Lift-It Sling Safety Program is concise and coordinates the users, the inspection process and your facility. The program results in an ongoing and viable system that protects the sling user, property and the corporate bottom line. The Sling Safety Program provides detailed instruction to all parties who are involved in rigging and hoisting loads. Participants should include specialized and incidental riggers, sling inspectors, safety and training, loss control, quality assurance, tool room and purchasing personnel. Our goal is accident prevention through education. The cost for our services is truly incidental when compared to expense of a single incident. If together we prevent just one accident, then we have accomplished our objective. Contact us for a mutually convenient training date and take the first step to improve overall efficiency and safety consciousness.

ON-SITE PROGRAMS
Thousands of sling users and inspectors have been educated, on location, through the Lift-It Sling Safety Program. The preferred program is a two day seminar. Day one features either and eight hour sling user /inspector class or two of the four classes. Day two features a sling inspector class and a facility program. Arrange the four hour class modules in any sequence desired to attain your specific scheduling and training objectives. Invite other interested parties to your program and share not only the cost, but the benefit.

L I F T- I T M A N U FA C T U R I N G C O M PA N Y, I N C .
4780 CORONA AVENUE LOS ANGELES, CA 90058-3808 (323) 582-6076 FAX (323) 587-1630 E-mail: [email protected] Visit our web site at www.lift-it.com

When Only the Best is Good Enough

2006, Lift-It Manufacturing Co., Inc.

Copyright infringements will be actively pursued and violators will be prosecuted to the fullest extent of the law. Printed in the U.S.A. TPPIB1-Rev 1
June 2006