CalibrationXmsn - Testing Adjusting

Service Information System
Pgina 1 de 44
Testing and Adjusting

D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II, D8R Series II, D10R and D11R Track-Type Tractors and 572R Pipelayer Power Train Electronic Control System
Media Number -SENR8367-10 Publication Date -01/05/2003 Date Updated -20/05/2003 i01860871
Calibration
SMCS - 4800-524 S/N - 1RW1-UP S/N - 2EN1-UP S/N - 2HM1-UP S/N - 2HR1-UP S/N - 2HZ1-UP S/N - 2YN1-UP S/N - 3CR1-UP S/N - 3DN1-UP S/N - 3WN1-UP S/N - 3ZN1-UP S/N - 3ZR1-UP S/N - 4FM1-UP S/N - 4HN1-UP S/N - 4HS1-UP S/N - 4JN1-UP S/N - 4JR1-UP S/N - 4MN1-UP S/N - 4SR1-UP S/N - 4TR1-UP S/N - 4WR1-UP S/N - 5ES1-UP
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004
Pgina 2 de 44
S/N - 5LN1-UP S/N - 5MR1-UP S/N - 5NR1-UP S/N - 5PR1-UP S/N - 5RR1-UP S/N - 6AS1-UP S/N - 6ER1-UP S/N - 6FR1-UP S/N - 6GN1-UP S/N - 6GR1-UP S/N - 6HR1-UP S/N - 6JN1-UP S/N - 6LR1-UP S/N - 6MR1-UP S/N - 6YZ1-UP S/N - 7AR1-UP S/N - 7DR1-UP S/N - 7GR1-UP S/N - 7KN1-UP S/N - 7LR1-UP S/N - 8LN1-UP S/N - 8TM1-UP S/N - 8XN1-UP S/N - 9BM1-UP S/N - 9HM1-UP S/N - 9MN1-UP S/N - 9PN1-UP S/N - 9ZS1-UP
Pgina 3 de 44
S/N - AAC1-UP S/N - ABJ1-UP S/N - ACJ1-UP S/N - ADE1-UP S/N - AEM1-UP S/N - AFD1-UP S/N - AFM1-UP S/N - AGG1-UP S/N - AGM1-UP S/N - AGN1-UP S/N - AKA1-UP S/N - AKD1-UP S/N - AKM1-UP S/N - ALH1-UP S/N - ALR1-UP S/N - ALY1-UP S/N - BLT1-UP S/N - BMK1-UP S/N - BMY1-UP S/N - BNL1-UP S/N - BNM1-UP S/N - BNX1-UP S/N - BPK1-UP S/N - BPM1-UP S/N - BPP1-UP S/N - BPS1-UP S/N - BPT1-UP
Pgina 4 de 44
S/N - BPZ1-UP S/N - BRE1-UP S/N - BRJ1-UP S/N - BRM1-UP S/N - BRP1-UP S/N - BRZ1-UP S/N - CAD1-UP S/N - CBF1-UP S/N - CBL1-UP S/N - CCG1-UP S/N - CCS1-UP S/N - CFH1-UP S/N - DMP1-UP S/N - FDT1-UP
Using the Caterpillar Monitoring System for the System Calibration of the D5M, D6M, D6R, D6R Series II, D7R, D7R Series II, D8R Series II, and 572R
The following chart provides specifications for system calibration on the various machine models. Table 1 Calibration Specifications Sales Model Steer Type Trans Type Track Type App No. Steering Clutch High Pressure Steering Clutch Low Pressure Brake Low Pressure
D5M
Clt/Brk
PSDD
LGP
696
2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa
50 35 kPa (7 50 35 kPa (7 5 psi) 5 psi) 50 35 kPa (7 50 35 kPa (7 5 psi) 5 psi) 50 35 kPa (7 50 35 kPa (7
D5M
Clt/Brk
PSTC
XL
697
D5M
Clt/Brk
PSTC
LGP
698
Pgina 5 de 44
(325 4 psi) D5N Clt/Brk PSTC XL 850 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) NA
5 psi)
5 psi)
35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 50 35 kPa (7 50 35 kPa (7 5 psi) 5 psi) 50 35 kPa (7 50 35 kPa (7 5 psi) 5 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi) 35 20 kPa (5 3 psi) 35 20 kPa (5 3 psi)
D5N
Clt/Brk
PSTC
LGP
852
D6M
Clt/Brk
PSTC
XL
694
D6M
Clt/Brk
PSTC
LGP
695
D6N
Diff/Steer
PSTC
XL
855
D6N
Diff/Steer
PSTC
LGP
857
D6R
Clt/Brk
PSTC
STD
705
D6R
Clt/Brk
PSTC
XL
708
D6R
Clt/Brk
PSTC
XR
710
D6R
Clt/Brk
PSTC
LGP
712
D6R
Clt/Brk
PSDD
LGP
747
D6R
Diff/Steer
PSTC
STD
706
D6R
Diff/Steer
PSTC
XL
709
NA
NA
D6R
Diff/Steer
PSTC
XR
711
NA
NA
Pgina 6 de 44
D6R D6R Series II D6R Series II D6R Series II D6R Series II D6R Series II D6R Series II D6R Series II D6R Series II
Diff/Steer
PSTC
LGP
713
NA
NA
35 20 kPa (5 3 psi)
Clt/Brk
PSTC
STD
897
2275 30 kPa (330 4 psi) NA
35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)
Diff/Steer
PSTC
STD
898
Clt/Brk
PSTC
XL
899
2275 30 kPa (330 4 psi) NA
Diff/Steer
PSTC
XL
900
Clt/Brk
PSTC
LGP
903
2275 30 kPa (330 4 psi) NA
35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi) 35 20 kPa (5 3 psi)
Diff/Steer
PSTC
LGP
904
Diff/Steer
PSTC
XW
905
NA
NA
Clt/Brk
PSTC
LGP
906
2275 30 kPa (330 4 psi) NA
D6RLS
Diff/Steer
PSTC
LGP
715
D7R
Clt/Brk
PSTC
STD
716
2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) NA
35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) 35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi) 35 20 kPa (5 3 psi)
D7R
Clt/Brk
PSTC
LGP
717
D7R
Diff/Steer
PSTC
STD
718
D7R D7R
Diff/Steer
PSTC
LGP
719
NA
NA
Pgina 7 de 44
Series II D7R Series II D7R Series II D7R Series II D7R Series II D7R Series II
Clt/Brk Diff/Steer
PSTC
STD
881
2275 30 kPa (330 4 psi) NA
PSTC
STD
884
Clt/Brk
PSTC
XR
882
2275 30 kPa (330 4 psi) NA
Diff/Steer
PSTC
XR
885
Clt/Brk
PSTC
LGP
883
2275 30 kPa (330 4 psi) NA
Diff/Steer
PSTC
LGP
886
572R D8R Series II
Clt/Brk
PSTC
STD
827
2240 30 kPa (325 4 psi) NA
Diff/Steer
PSTC
STD
849
Note: The submodes 01 through 40 are used to perform actual tests and adjustments. Enter the submodes when you are performing the procedures that are listed in this manual only. For more information, see System Operation, "Calibration Operation". Note: If the ET service tool is used in order to perform the calibrations, see "Performing Calibrations With the ET Service Tool".
Accessing Calibration And Display Modes Of The Monitoring System
View Image
Pgina 8 de 44
Illustration 1 4C-8195 Control Service Tool (1) Mode Switch (2) Clear Switch (3) Scroll Switch
g00860708
View Image
Pgina 9 de 44
Illustration 2 g00597263 Typical Example of the Main Display Module of the Caterpillar Monitoring System (4) Display Area. (5) Diagnostic Code Indicator ("SERV CODE").
Table 2 Calibration Modes Parking Brake Status Submode (1) Number
Submode Description
Steering/Braking Calibration Mode Mode No. 6... D6R Series II, D7R Series II, D8R Series II, D10R, and D11R Mode No. 5... D5M, D6M, D6R, and D7R ON OFF OFF ON ON 01 02 03 04 05 Set Application Left Brake Adjustment Right Brake Adjustment Left Steer Clutch High Pressure Adjustment Right Steer Clutch High Pressure Adjustment
Pgina 10 de 44
OFF OFF ON ON
06 07 08 09
Left Brake Low Pressure Adjustment Right Brake Low Pressure Adjustment Left Steer Clutch Low Pressure Adjustment Right Steer Clutch Low Pressure Adjustment
Transmission Calibration Mode Mode No. 7... D6R Series II, D7R Series II, D8R Series II, D10R, and D11R Mode No. 6... D5M, D6M, D6R, and D7R ON ON ON ON ON ON ON ON ON 20 21 22 31 32 33 34 35 40 Set Forward High Speed Lockout Set Reverse High Speed Lockout Transmission Direction Lever Adjustment Clutch 1 Engagement Calibration Clutch 2 Engagement Calibration Clutch 3 Engagement Calibration Clutch 4 Engagement Calibration Clutch 5 Engagement Calibration Clutch Fill Calibration
Component Data Display Mode Mode No. 8... D6R Series II, D7R Series II, D8R Series II, D10R, and D11R Mode No. 7... D5M, D6M, D6R, and D7R ON
(1)
None
Component Data
Only the submodes that are required for a particular machine will appear. Submodes 10 through 19, 23 through 30, and 36 through 39 are not used at this time.
Service personnel access the calibration submodes by using the 4C-8195 Control Service Tool . To Enter A Mode - Press and hold the "MODE" switch (1). Release the "MODE" switch when the desired mode number from the chart is shown in display area (4). To Scroll Through The Submodes - Press and hold the SCROLL switch (3). Release the SCROLL switch when the correct number for the submode is being shown. To Adjust A Value Within A Submode - The "+" and "-" positions of CLEAR switch (2) are used to change the value within a submode. To Scroll Through The Component Identifiers Of Component Data Display Mode - Use the "+" and "-" positions of CLEAR switch (2) in order to move through the component list.
Component Data Display Mode
Pgina 11 de 44
Note: The component data display mode for the D5M, D6M, D6R, D7R, and 572R is Mode No. 7. For the D6R Series II, D7R Series II, D8R Series II, the mode is Mode No. 8. The component data display mode will show the values of data that is received by the ECM from system components of the power train. Each component is referenced by a unique Component Identifier. Use the "+" and "-" positions of the CLEAR switch that is on the service tool to move through the component list. The identifying number for a component will be displayed for 2 seconds. The parameter value for that component will be displayed after the identifying number is displayed. The components are listed in numerical order of the identifying number. For a list of Component Identifiers, see the table below. The values for different types of components appear in the following forms:
The data for the position sensor is displayed in "%" duty cycle. The data for the temperature sensor is displayed in C.
Data for switches is displayed by using "O" and "C" for each throw of the switch. "O" stands for "Open". "C" stands for "Closed". The normally open contact is displayed by the left character for double-throw switches. The normally closed contact is displayed by the right character. Currents for proportional solenoids are shown on a 0 - 255 scale. "0" represents no current and "255" represents full current (1.25 Amperes). Currents for On/Off solenoids are displayed by using "0" for OFF and "1" for ON.
Performing Calibrations With the ET Service Tool

In order to perform calibrations by using the ET service tool, connect ET and select the "Steering/Braking/Trans ECM". Select "Calibrations" from the "Service Menu" and then select the desired calibrations from the sub-menu. The calibrations are grouped into general categories. Note: "Steering, Clutch/Brake Pressure Calibrations" and "Brake Touch-Up Calibrations" will include calibrations that do not apply for differential steering tractors. For differential steering tractors, unselect all calibrations in these two categories except "Left Brake Low Pressure Calibration" and "Left Brake Touch-Up Calibration". These are the only calibrations that apply to differential steering machines in these two categories. If the other calibrations are performed in these categories ET will indicate that the procedure failed. This failure warning can be ignored. Once the desired calibrations have been selected the calibration process can be performed by pressing the "Begin" key and then following the instructions displayed on the screen. Note: If a calibration fails when you use the Cat ET, try performing the same calibration by using the Caterpillar Monitoring System. Table 3 Component Data Display Description Component Number 0000 Component Description Steering/Brake Sensors Quick Check Normal Conditions and Limits Steering Levers: 0 = released
Data Format Left character = left steering lever
Pgina 12 de 44
Middle character = right steering lever Right character = service brake pedal 572R Pipelayer: First character = left steering lever Second character = right steering lever Third character = left brake pedal Fourth character = right brake pedal 0070 Parking Brake Switch Left character = normally open contact Right character = normally closed contact O = contact open C= contact closed Degrees C
1 = detent 2 = full stroke "-" = in between Brake Pedals: 0 = released 1 = fully depressed "-" = in between
OC = parking brake released CO = parking brake applied CC = invalid switch state OO = invalid switch state 40 to 127 = normal range -999 = out of range low 999 = out of range high 0 to 4000 = display range O = normal for pedal release C = normal for pedal depress Finger Tip Control: CO 6% < Reverse < 27% OC 32% < Neutral < 47% OC 54% < Forward < 79% Differential Steer: CO 11% < Reverse < 33% OC 40% < Neutral < 60% OC 65% < Forward < 92%
0177
Transmission Oil Temperature Sensor Engine Speed Sensor Brake Pedal Switch
0190 0298
RPM O = contact open C = contact closed
0299
Transmission (Direction) Lever Position Sensor
Right side = % Duty Cycle Left side first character = direction switch normally open contact Left side second character = direction switch normally closed contact
0468
Implement Lockout Switches
Left character = normally open contact Right character = normally closed contact O = contact open
OC = Implement locked out CO = Implement enabled CC = invalid switch state OO = State not
Pgina 13 de 44
C= contact closed 0490 Brake Pedal Position Sensor Brake Pedal Position Sensor D5N, D6N Only 0573 0621 Inching Pedal Position Sensor Downshift Switch Right side = % Duty Cycle left side = brake pedal switch contact Right side = % Duty Cycle Left side = brake pedal % Duty Cycle Left character = normally open contact Right character = normally closed contact O = contact open C= contact closed Left character = normally open contact Right character = normally closed contact O = contact open C= contact closed Left character = normally open contact Right character = normally closed contact O = contact open C= contact closed RPM RPM RPM RPM
determined O 8% < Released < 37% C Depressed < 61% O 8%< Released <34% C Depressed 65% 5% < Released < 37% Depressed < 67% OC = switch released CO = switch depressed CC = invalid switch state OO = invalid switch state
0622
Upshift Switch
OC = switch released CO = switch depressed CC = invalid switch state OO = invalid switch state
0623
Direction Switch (Reverse)
CO = Reverse OC = Neutral OC = Forward CC = invalid switch state OO = invalid switch state 0 to 5000 = display range 0 to 5000 = display range 0 to 5000 = display range 0 to 3000 = display range
0671 0672 0673 0674
Transmission Output Speed Sensor 1 Torque Converter Output Speed Sensor Transmission Output Speed Sensor 2 Transmission Intermediate Speed Sensor 1 Transmission Intermediate Speed Sensor 2 Left Steering Lever Position Sensor Right Steering Lever Position Sensor Parking Brake Solenoid
0675
RPM
0 to 3000 = display range
0676 0677 0681
% Duty Cycle (1) % Duty Cycle (1) Unitless command value
4% < Released < 22% Full Stroke < 90% 4% < Released < 22% Full Stroke < 90% 0 = solenoid off
Pgina 14 de 44
1 = solenoid on 0689 0690 0691 0692 0693 0694 0695 0697 0698 0699 0722 Left Brake Solenoid Right Brake Solenoid Unitless command value Unitless command value 0 to 215 = possible range 0 to 215 = possible range 0 to 255 = possible range 0 to 255 = possible range 0 to 255 = possible range 0 to 255 = possible range 0 to 255 = possible range 0 = solenoid off 1 = solenoid on 0 to 215 = possible range 0 to 215 = possible range 0 = solenoid off 1 = solenoid on O 8% < Released < 37% C Depressed < 61% O 8% < Released < 37% C Depressed < 61% O = normal for pedal release C = normal for pedal depress O = normal for pedal release C = normal for pedal depress 0 = electromagnet OFF 1 = electromagnet ON Display shows last five
Reverse Clutch Solenoid Unitless command value Forward Clutch Solenoid Unitless command value
Speed 3 Clutch Solenoid Unitless command value Speed 2 Clutch Solenoid Unitless command value Speed 1 Clutch Solenoid Unitless command value Priority Valve Left Steering Clutch Solenoid Right Steering Clutch Solenoid Secondary Brake Solenoid Left Brake Pedal Position Sensor (pipelayer) Right Brake Pedal Position Sensor (pipelayer) Left Brake Pedal Switch (pipelayer) Unitless logic state value Unitless command value Unitless command value Unitless logic state value Right side = % Duty Cycle left side = brake pedal switch contact Right side = % Duty Cycle left side = brake pedal switch contact O = contact open C = contact closed
1327
1328
1329
1330
Right Brake Pedal Switch (pipelayer) Implement Lever Detent Electromagnet Software Part Number
O = contact open C = contact closed
1488 SPN
0 or 1 Numeric Text Characters
Pgina 15 de 44
digits of software part number

(1)
The difference in duty cycle from the fully deflected forward to the fully deflected rearward positions must be greater than 61%. If the difference between the two extremes is less than 61% the function will not operate.
Submode 01 - Set Application

This submode is used to set the application number for the Power Train Electronic Control System. The application number is specified in table 1. Note: The mode for the "steering/braking calibration" for the D5M, D6M, D6R, and D7R and on all Series II machines is Mode Number 5.
Procedure
1. In table 1, find the application number that matches the sales model, the serial number prefix, the type of steering, the type of transmission, and the type of track for the machine that is being adjusted. 2. Place the parking brake switch in the ON position. 3. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration". Then, enter submode 01. 4. Use the "+" and "-" positions of the CLEAR switch in order to move through the list of application numbers until the correct application number from Step 3 is displayed. 5. Exit submode 01 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 02 - Left Brake Touch Up Adjustment

This submode sets the command value from the ECM for the brake touch-up. The ECM applies a current for 20 seconds to the left brake solenoid when the CLEAR switch is placed in the "-" position. The ECM will turn off the current after the CLEAR switch is momentarily placed in the "+" position or after the current has been applied for 20 seconds. Observe the track speed while the current is being applied in order to complete the adjustment of the brake. Note: This calibration provides smooth brake engagement. Many conditions can affect this calibration. Some conditions that can affect the calibration are power train oil temperature and track tension. If the calibration procedures for submode 2 and for submode 3 are performed and there is harsh engagement of the brakes, readjust the values that were set in the calibration procedure.
Left Brake Adjustment Procedure For Power Shift Torque Converter (PSTC) Transmission
1. Warm up the power train oil to a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands may be used or the blade and the ripper may be used. Note: The procedure can be performed with the track on the ground. If these procedures are performed with the machine on the ground, the ground surface should be hard and level.
Pgina 16 de 44
2. Release the parking brake. Set the engine speed to low idle for the D6R Series II, D7R Series II, and D8R Series II. Set the engine speed to 910 RPM for the D5M, D6M, D6R, and D7R. 3. With the 4C-8195 Control Service Tool, enter the "Steering/Braking Calibration Mode". Enter submode 02. 4. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 5. Begin the test. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the left brake solenoid for 20 seconds. 6. Observe the left track in order to determine if the left track stops. Wait for 20 seconds in order to determine if the track stops. DO NOT press the CLEAR switch more than one time during the same test. The test current is removed automatically after 20 seconds. The track speed will return to normal speed. The track can also be returned to normal speed by pressing and then releasing the CLEAR switch to the INCREMENT ("+") position.
If the left track STOPS before returning to normal speed, the preset value must be increased to 5 units higher. The present value is shown on the display. This creates a new starting point. Press and release the CLEAR switch to the INCREMENT ("+") position until the value is changed. Proceed to 5 and repeat the test. If the left track DOES NOT STOP before returning to normal speed, proceed to Test Step 7.
7. Decrease the present value that is showing on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value is changed. The 20 second test will begin again. Observe the left track in order to determine if the track stops. Wait for 20 seconds for the track to stop.
If the left track STOPS at any time before returning to normal speed, calibration of the left brake is complete. Exit submode 02 by scrolling to the next submode. Use the SCROLL switch or use the MODE switch also to exit the calibration. If the left track DOES NOT STOP before returning to normal speed, exit this procedure and perform this procedure again.
Left Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)
Note: This procedure is NOT for R-Series II machines. For R-Series II machines, proceed to the bottom of this procedure. The following procedure requires monitoring engine speed. Engine speed can be monitored by using the status screens in the Caterpillar Electronic Technician (ET) or by using an external tachometer. If the ability to monitor engine speed is not available, use the "Alternate Left Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)". 1. Warm up the power train oil to a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If these procedures are
Pgina 17 de 44
performed with the machine on the ground, the ground surface should be hard. The ground surface should also be level. 2. Release the parking brake. Set the engine speed to 910 5 RPM. 3. Shift the transmission to third gear forward and allow the tracks to rotate for at least three seconds. After three seconds, record the average engine speed as engine speed "A". 4. Calculate engine speed "B" with the following formulas: D5M - engine speed "B" RPM = engine speed "A" RPM - 27 RPM D6R - engine speed "B" RPM = engine speed "A" RPM - 115 RPM 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 02. 6. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 7. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the left brake solenoid for 20 seconds. 8. Wait at least three seconds from the start of the test. Observe engine speed in order to determine if the speed drops below engine speed ("B"). Wait for 20 seconds so that the engine speed can stabilize. DO NOT press the CLEAR switch more than one time during the same test. After 20 seconds, the test current is automatically removed and engine speed and track speed will return to normal speed. The engine and the track can also be returned to normal speed by pressing the CLEAR switch to the INCREMENT position ("+") and then releasing the switch.
If the speed of the engine drops below engine speed "B" and the engine has not returned to normal speed, increase the present value that is shown on the display to 5 units higher. Press and release the CLEAR switch to the INCREMENT position ("+") until the value has changed. Return to Step 5 in order to repeat the test. If the speed of the engine does not drop below engine speed "B" and the engine has returned to normal speed, proceed to Test Step 9.
9. Decrease the present value that is shown on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 second test will begin again. Wait at least three seconds. Observe the engine speed to determine if the speed drops below engine speed "B". Wait for 20 seconds so that the engine speed can stabilize.
If the speed of the engine drops below engine speed "B" and the engine has not returned to normal speed, the calibration of the left brake touch up is complete. Exit submode 02 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. If the speed of the engine does not drop below engine speed "B" and the engine has returned to normal speed, exit this procedure and perform this procedure again.
Pgina 18 de 44
Left Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS) On R Series II Machines
The following procedure requires monitoring engine fuel position. Engine fuel position can be monitored using the status screens (engine) in the Caterpillar Electronic Technician (ET) or the left brake adjustment procedure should be performed using the Caterpillar Electronic Technician (ET). If the ability to monitor engine fuel position is not available, use the "Alternate Left Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)". 1. Warm up the power train oil a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If these procedures are performed with the machine on the ground, the ground surface should be hard and level. 2. Release the parking brake. Set the engine speed to low idle (800 RPM). 3. Shift the transmission to third gear forward and allow the tracks to rotate for at least three seconds. After 3 seconds, record the average engine fuel position as fuel position "A". 4. Calculate engine fuel position "B" with the following formula: D6R, Series II - engine fuel position "B" = engine fuel position "A" + 15 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then enter submode 02. 6. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 7. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the left brake solenoid for 20 seconds. 8. Wait at least three seconds from the start of the test. Observe engine fuel position in order to determine if the engine fuel position increases above engine fuel position "B". Wait for 20 seconds so that the engine fuel position can stabilize. DO NOT press the clear switch more than one time during the same test. After 20 seconds, the test current is automatically removed. The left brake adjustment test current can also be returned to normal by pressing the CLEAR switch to the INCREMENT position ("+") and then releasing the switch. * If the engine fuel position increases above engine fuel position "B" and the engine fuel position has not returned to normal, increase the present value that is shown on the display to 5 units higher. Press and release the CLEAR switch to the INCREMENT position ("+") until the value has changed. Return to Step 5 in order to repeat the test. * If the engine fuel position does not increase above engine fuel position "B" and the engine fuel position has returned to normal, proceed to Test Step 9. 9. Decrease the present value that is shown on the display to 1 unit lower. Press and released the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 seconds test will begin again. Wait at least three seconds. Observe the engine fuel position to determine if the engine fuel position increases above engine fuel position "B". Wait for 20 seconds so that the engine fuel position can stabilize. * If the engine fuel position increases above the engine fuel position "B" and the engine fuel position has not returned to normal, the calibration of the left brake touch up is complete. Exit submode 02 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. * If the engine fuel position does not increase above the engine fuel position "B" and the
Pgina 19 de 44
engine fuel position has returned to normal, repeat Step 9.
Alternate Left Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)
Note: This procedure is NOT for R-Series II machines. For R-Series II machines, proceed to the bottom of this procedure. 1. Warm up the power train oil to a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If this procedure is performed with the machine on the ground, the ground surface should be hard. The ground surface should also be level. 2. Release the parking brake. Set the engine speed to 910 5 RPM. 3. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 02. 4. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 5. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the left brake solenoid for 20 seconds. 6. Observe the left track for a visible decrease in track speed. Wait for 20 seconds so that the track speed can decrease. DO NOT press the CLEAR switch more than one time during the same test. After 20 seconds, the test current is automatically removed and track speed will return to normal speed. The track can also be returned to normal speed by pressing the CLEAR switch to the INCREMENT ("+") position and then releasing the switch.
If the speed of the left track DECREASES at any time before returning to normal speed, increase the present value that is shown on the display to 5 units higher. Press and release the CLEAR switch to the INCREMENT position ("+") until the value has changed. Return to Step 5 in order to repeat the test. If the speed of the left track DOES NOT DECREASE before returning to normal speed, proceed to 7.
7. Decrease the present value that is shown on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 second test will begin again. Observe the left track for a visible decrease in track speed. Wait for 20 seconds so that the speed can decrease.
If the speed of the left track DECREASES at any time before returning to normal speed, calibration of the left brake is complete. Exit submode 02 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. If the speed of the left track DOES NOT DECREASE before returning to normal speed, repeat Step 7.
Pgina 20 de 44
Alternate Left Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS) On R-Series II Machines
1. Warm up the power train oil a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If these procedures are performed with the machine on the ground, the ground surface should be hard and level. 2. Release the parking brake. Set the engine speed to low idle (800 RPM). 3. Shift the transmission to third gear forward and allow the tracks to rotate for at least three seconds. After three seconds, record the average engine speed as engine speed "A". 4. Calculate engine speed "B" with the following formula: D6R Series II - engine speed "B" = engine speed "A" - 25 RPM. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then enter submode 02. 6. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 7. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the left brake solenoid for 20 seconds. 8. Observe the engine speed for a visible decrease in track speed. The decrease in track speed will last one to two seconds before returning to normal speed. DO NOT press the CLEAR switch more than one time during the same test. After 20 seconds, the test current is automatically removed. The left brake adjustment test current can also be returned to normal by pressing the CLEAR switch to the INCREMENT position ("+") and then releasing the switch. * If the engine speed drops below engine speed "B" at any time before returning to normal speed, increase the present value that is shown on the display to 5 units higher. Press and release the CLEAR switch to INCREMENT position ("+") until the value has changed. Return to Step 5 in order to repeat the test. * If the engine speed does not drop below engine speed "B" at any time before returning to normal speed, proceed to Step 9. 9. Decrease the present value that is shown on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 second test will begin again. Observe the engine speed to determine if the engine speed drops below engine speed "B" at any time. * If the engine speed drops below engine speed "B" at any time before returning to normal speed, the calibration of the left brake touch up is complete. Exit submode 02 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. * If the engine speed does not drop below engine speed "B" at any time before returning to normal speed, repeat Step 9.
Submode 03 - Right Brake Touch Up Adjustment

This submode sets the command value for a smooth brake touch up. The ECM applies a test current for 20 seconds to the right brake solenoid when the CLEAR switch is placed in the DECREMENT ("-") position. The ECM will turn off the test current when the CLEAR switch is placed in the INCREMENT ("+") position or when the test current has been applied for 20 seconds. The brake adjustment is performed by observing the effect of the test current on the speed of the track.
Pgina 21 de 44
Note: This calibration provides smooth brake engagement. Many conditions can affect this calibration. Some conditions that can affect the calibration are power train oil temperature and track tension. If the calibration procedures for submode 2 and for submode 3 are performed and there is harsh engagement of the brakes, readjust the values that were set in the calibration procedure.
Right Brake Adjustment Procedure For Power Shift Torque Converter (PSTC) Transmission
1. Warm up the power train oil to a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If these procedures are performed with the machine on the ground, the ground surface should be hard and level. 2. Release the parking brake. Set the engine speed to low idle for the D6R Series II, D7R Series II, and D8R Series II. Set the engine speed to 910 RPM for the D5M, D6M, D6R, and D7R. 3. With the 4C-8195 Control Service Tool, enter the "Steering/Braking Calibration Mode". Then, enter submode 03. 4. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 5. Begin the test by pressing the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the right brake solenoid for 20 seconds. 6. Observe the right track in order to determine if the track stops. Wait for 20 seconds for the track to stop. DO NOT press the CLEAR switch more than one time during the same test. After 20 seconds, the test current is automatically removed and the track speed will return to normal speed. The track can also be returned to normal speed by pressing the CLEAR switch to the INCREMENT ("+") position and then releasing the switch.
If the right track STOPS at any time before returning to normal speed, increase the present value to 5 units higher. The value is shown on the display. Press and release the CLEAR switch to the INCREMENT ("+") position until the value is changed. Return to 5 and repeat the test. If the right track DOES NOT STOP before returning to normal speed, proceed to the next step.
7. Decrease the present value that is shown on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value is changed. The 20 second test will begin again. Observe the right track in order to determine if the track stops. Wait for 20 seconds for the track to stop.
If the right track STOPS at any time before returning to normal speed, calibration of the right brake is complete. Exit submode 03 by scrolling to the next submode. The SCROLL switch and the MODE switch can also be used to exit the calibration. If the right track DOES NOT STOP before returning to normal speed, return to 7.
Right Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)
Pgina 22 de 44
Note: This procedure is NOT for R-Series II machines. For R-Series II machines, proceed to the bottom of this procedure. The following procedure requires monitoring engine speed. Engine speed can be monitored by using the status screens in the Caterpillar Electronic Technician (ET) or by using an external tachometer. If the ability to monitor engine speed is not available, use the "Alternate Right Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)". 1. Warm up the power train oil to a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If these procedures are performed with the machine on the ground, the ground surface should be hard. The ground surface should also be level. 2. Release the parking brake. Set the engine speed to 910 5 RPM. 3. Shift the transmission to third gear forward and allow the tracks to rotate for at least three seconds. After three seconds, record the average engine speed as engine speed "A". 4. Calculate engine speed "B" with the following formulas: D5M - engine speed "B" RPM = engine speed "A" RPM - 27 RPM D6R - engine speed "B" RPM = engine speed "A" RPM - 115 RPM 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 03. 6. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 7. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the right brake solenoid for 20 seconds. 8. Wait at least three seconds from the start of the test. Observe engine speed in order to determine if the speed drops below engine speed ("B"). Wait for 20 seconds so that the engine speed can stabilize. DO NOT press the CLEAR switch more than one time during the same test. After 20 seconds, the test current is automatically removed and engine speed and track speed will return to normal speed. The engine and the track can also be returned to normal speed by pressing the CLEAR switch to the INCREMENT position ("+") and then releasing the switch.
If the speed of the engine drops below engine speed "B" and the engine has not returned to normal speed, increase the present value that is shown on the display to 5 units higher. Press and release the CLEAR switch to the INCREMENT position ("+") until the value has changed. Return to Step 5 in order to repeat the test. If the speed of the engine does not drop below engine speed "B" and the engine has returned to normal speed, proceed to 9.
9. Decrease the present value that is shown on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 second test will begin again. Wait at least three seconds. Observe the engine speed to determine if the
Pgina 23 de 44
speed drops below engine speed "B". Wait for 20 seconds so that the engine speed can stabilize.
If the speed of the engine drops below engine speed "B" and the engine has not returned to normal speed, the calibration of the right brake touch up is complete. Exit submode 03 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. If the speed of the engine does not drop below engine speed "B" and the engine has returned to normal speed, Repeat Step 9.
Right Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS) On R-Series II Machines
The following procedure requires monitoring engine fuel position. Engine fuel position can be monitored using the status screens (engine) in the Caterpillar Electronic Technician (ET) or the right brake adjustment procedure should be performed using the Caterpillar Electronic Technician (ET). If the ability to monitor engine fuel position is not available, use the "Alternate Right Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)". 1. Warm up the power train oil a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If these procedures are performed with the machine on the ground, the ground surface should be hard. The ground surface should also be level. 2. Release the parking brake. Set the engine speed to low idle (800 RPM). 3. Shift the transmission to third gear forward and allow the tracks to rotate for at least three seconds. After 3 seconds, record the average engine fuel position as fuel position "A". 4. Calculate engine fuel position "B" with the following formula: D6R, Series II - engine fuel position "B" = engine fuel position "A" + 15 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then enter submode 03. 6. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 7. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the right brake solenoid for 20 seconds. 8. Wait at least three seconds from the start of the test. Observe engine fuel position in order to determine if the engine fuel position increases above engine fuel position "B". Wait for 20 seconds so that the engine fuel position can stabilize. DO NOT press the clear switch more than one time during the same test. After 20 seconds, the test current is automatically removed. The right brake adjustment test current can also be returned to normal by pressing the CLEAR switch to the INCREMENT position ("+") and then releasing the switch.
If the engine fuel position increases above engine fuel position "B" and the engine fuel position has not returned to normal, increase the present value that is shown on the
Pgina 24 de 44
display to 5 units higher. Press and release the CLEAR switch to the INCREMENT position ("+") until the value has changed. Return to Step 5 in order to repeat the test.
If the engine fuel position does not increase above engine fuel position "B" and the engine fuel position has returned to normal, proceed to Step 9.
9. Decrease the present value that is shown on the display to 1 unit lower. Press and released the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 seconds test will begin again. Wait at least three seconds. Observe the engine fuel position to determine if the engine fuel position increases above engine fuel position "B". Wait for 20 seconds so that the engine fuel position can stabilize.
If the engine fuel position increases above the engine fuel position "B" and the engine fuel position has not returned to normal, the calibration of the right brake touch up is complete. Exit submode 02 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. If the engine fuel position does not increase above the engine fuel position "B" and the engine fuel position has returned to normal, repeat Step 9.
Alternate Right Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS)
Note: This procedure is NOT for R-Series II machines. For R-Series II machines, proceed to the bottom of this procedure. 1. Warm up the power train oil to a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If this procedure is performed with the machine on the ground, the ground surface should be hard. The ground surface should also be level. 2. Release the parking brake. Set the engine speed to 910 5 RPM. 3. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 03. 4. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 5. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the right brake solenoid for 20 seconds. 6. Observe the right track for a visible decrease in track speed. Wait for 20 seconds so that the track speed can decrease. DO NOT press the CLEAR switch more than one time during the same test. After 20 seconds, the test current is automatically removed and track speed will return to normal speed. The track can also be returned to normal speed by pressing the CLEAR switch to the INCREMENT ("+") position and then releasing the switch.
If the speed of the right track DECREASES at any time before returning to normal speed, increase the present value that is shown on the display to 5 units higher. Press and release the CLEAR switch to the INCREMENT position ("+") until the value has
Pgina 25 de 44
changed. Return to Step 5 in order to repeat the test.

If the speed of the right track DOES NOT DECREASE before returning to normal speed, proceed to 7.
7. Decrease the present value that is shown on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 second test will begin again. Observe the right track for a visible decrease in track speed. Wait for 20 seconds so that the speed can decrease.
If the speed of the right track DECREASES at any time before returning to normal speed, calibration of the right brake is complete. Exit submode 03 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. If the speed of the right track DOES NOT DECREASE before returning to normal speed, repeat Step 7.
Alternate Right Brake Adjustment Procedure For Direct Drive Power Shift Transmission (DDPS) On R-Series II Machines
1. Warm up the power train oil a minimum of 60 C (140 F). Lift the tractor off the ground. Jack stands can be used or the blade and the ripper can be used. Note: The procedure can be performed with the track on the ground. If these procedures are performed with the machine on the ground, the ground surface should be hard and level. 2. Release the parking brake. Set the engine speed to low idle (800 RPM). 3. Shift the transmission to third gear forward and allow the tracks to rotate for at least three seconds. After three seconds, record the average engine speed as engine speed "A". 4. Calculate engine speed "B" with the following formula: D6R Series II - engine speed "B" = engine speed "A" - 25 RPM. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then enter submode 03. 6. Shift the transmission to third gear forward and allow the tracks to rotate for several revolutions. 7. Press the CLEAR switch to the DECREMENT ("-") position and then release the switch. The test current will be applied to the right brake solenoid for 20 seconds. 8. Observe the engine speed for a visible decrease in engine speed. The decrease in track speed will last one to two seconds before returning to normal speed. DO NOT press the CLEAR switch more than one time during the same test. After 20 seconds, the test current is automatically removed. The left brake adjustment test current can also be returned to normal by pressing the CLEAR switch to the INCREMENT position ("+") and then releasing the switch.
If the engine speed drops below engine speed "B" at any time before returning to normal speed, increase the present value that is shown on the display to 5 units higher. Press and
Pgina 26 de 44
release the CLEAR switch to INCREMENT position ("+") until the value has changed. Return to Step 5 in order to repeat the test.
If the engine speed does not drop below engine speed "B" at any time before returning to normal speed, proceed to Step 9.
9. Decrease the present value that is shown on the display to 1 unit lower. Press and release the CLEAR switch to the DECREMENT ("-") position until the value has changed. The 20 second test will begin again. Observe the engine speed to determine if the engine speed drops below engine speed "B" at any time during 20 second test.
If the engine speed drops below engine speed "B" at any time before returning to normal speed, the calibration of the right brake touch up is complete. Exit submode 03 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration. If the engine speed does not drop below engine speed "B" at any time before returning to normal speed, repeat Step 9.
Submode 04 - Left Steering Clutch High Pressure Adjustment

This submode sets the pressure for full engagement for the left steering clutch.
Procedure
1. Warm up the power train oil to a minimum of 60 C (140 F). 2. Connect a pressure gauge that has a range up to at least 3447 kPa (500 psi) to the pressure fitting for the left steering clutch. The 8T-0855 Pressure Gauge or the 6V-7830 Pressure Gauge can be used. 3. Set the engine speed to high idle with the transmission in neutral. Put the parking brake switch in the brake ON position. 4. Refer to table 1 in order to find the value for the "Steering Clutch High Pressure". Find the value that corresponds to the application number of the machine that is being adjusted. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 04. 6. Use the INCREMENT position ("+") and the DECREMENT ("-") position of the CLEAR switch in order to adjust the clutch pressure until the pressure gauge shows the pressure that was found in Step 4. 7. Exit submode 04 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 05 - Right Steering Clutch High Pressure Adjustment

This submode sets the pressure for full engagement for the right steering clutch.
Pgina 27 de 44
Procedure
1. Warm up the power train oil to a minimum of 60 C (140 F). 2. Connect a pressure gauge that has a range up to at least 3447 kPa (500 psi) to the pressure fitting for the right steering clutch. The 8T-0855 Pressure Gauge or the 6V-7830 Pressure Gauge can be used. 3. Set the engine speed to high idle with the transmission in neutral. Put the parking brake switch in the brake ON position. 4. Refer to table 1 in order to find the value for the "Steering Clutch High Pressure". Find the value that corresponds to the application number of the machine that is being adjusted. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 05. 6. Use the INCREMENT ("+") and the DECREMENT ("-") positions of the CLEAR switch to adjust the clutch pressure until the pressure gauge shows the pressure that was found in Step 4. 7. Exit submode 05 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 06 - Left Brake Low Pressure Adjustment

This submode sets the lowest range of pressure for the left brake.
Procedure
1. Warm up the power train oil to a minimum of 60 C (140 F). 2. Connect a pressure gauge that has a range that is no greater than 483 kPa (70 psi). Connect the gauge in line with a valve to the pressure fitting for the left brake. The valve should be closed. The 8T-0853 Pressure Gauge or the 6V-7830 Pressure Gauge can be used.
NOTICE
Use of the 6V-7830 Pressure Gauge is highly recommended. It does not need a valve in line for protection. However, if a standard low pressure gauge such as 8T-0853 Pressure Gauge is used, a valve must be used in line with the gauge to protect the gauge from high pressure while changing submodes. If a valve is not used for the standard gauge, the gauge may become permanently damaged while changing submodes.
3. Set the engine speed to high idle with the transmission in neutral. Put the parking brake switch in the brake OFF position. 4. Refer to table 1 in order to find the value for the "Brake Low Pressure". Find the value that corresponds to the application number of the machine that is being adjusted. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then,
Pgina 28 de 44
enter submode 06. 6. Open the valve. Use the INCREMENT position ("+") and the DECREMENT position ("-") of the CLEAR switch to adjust the brake pressure until the pressure gauge shows the pressure that was found in Step 4. Note: The value in table 1 for the "brake low pressure" may not be attainable. This is due to various conditions. Some of the conditions are no low pressure gauge, gauge hysteresis, and cold power train oil. Bring the pressures as close as possible to the specified value. The adjustments for low brake pressure do not need to be exactly on the mark. 7. Close the valve or disconnect the gauge before submode 06 is exited. Exit submode 06 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 07 - Right Brake Low Pressure Adjustment

This submode sets the lowest range of pressure for the right brake.
Procedure
1. Warm up the power train oil to a minimum of 60 C (140 F). 2. Connect a pressure gauge that has a range that is no greater than 483 kPa (70 psi). Connect the gauge in line with a valve to the pressure fitting for the right brake. The valve should be closed. The 8T-0853 Pressure Gauge or the 6V-7830 Pressure Gauge can be used.
NOTICE
3. Set the engine speed to high idle with the transmission in neutral. Put the parking brake switch in the brake OFF position. 4. Refer to table 1 in order to find the value for the "Brake Low Pressure". Find the value that corresponds to the application number of the machine that is being adjusted. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode ". Then, enter submode 07. 6. Open the valve. Use the INCREMENT position ("+") and the DECREMENT position ("-") of the CLEAR switch to adjust the brake pressure to the pressure that was found in Step 4. Note: The value in table1 for the "brake low pressure" may not be attainable. This is due to various conditions. Some of the conditions are no low pressure gauge, gauge hysteresis, and cold power train oil. Bring the pressures as close as possible to the specified value. The
Pgina 29 de 44
adjustments for low brake pressure do not need to be exactly on the mark. 7. Close the valve or disconnect the gauge before submode 07 is exited. Exit submode 07 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 08 - Left Steering Clutch Low Pressure Adjustment

This submode sets the lowest pressure range for the left steering clutch.
Procedure
1. Warm up the power train oil to a minimum of 60 C (140 F). 2. Connect a pressure gauge that has a range that is no greater than 483 kPa (70 psi). Connect the gauge in line with a valve to the pressure fitting for the left steering clutch. The valve should be closed. The 8T-0853 Pressure Gauge or the 6V-7830 Pressure Gauge can be used.
NOTICE
3. Set the engine speed to high idle with the transmission in neutral. Put the parking brake switch in the "brake ON" position. 4. Refer to table 1 in order to find the value for the "Steering Clutch Low Pressure". Find the value that corresponds to the application number of the machine that is being adjusted. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode ". Then, enter submode 08. 6. Open the valve. Use the INCREMENT position ("+") and the DECREMENT position ("-") of the CLEAR switch to adjust the clutch pressure to the pressure that was found in Step 4. Note: The value in table 1 for the "steering clutch low pressure" may not be attainable. This is due to various conditions. Some of the conditions are no low pressure gauge, gauge hysteresis, and cold power train oil. Bring the pressures as close as possible to the specified value. The adjustments for "steering clutch low pressure" do not need to be exactly on the mark. 7. Close the valve or disconnect the gauge before submode 08 is exited. Exit submode 08 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 09 - Right Steering Clutch Low Pressure Adjustment

This submode sets the lowest pressure range for the right steering clutch.
Pgina 30 de 44
Procedure
1. Warm up the power train oil to a minimum of 60 C (140 F). 2. Connect a pressure gauge that has a range that is no greater than 483 kPa (70 psi). Connect the gauge in line with a valve to the pressure fitting for the right steering clutch. The valve should be closed. The 8T-0853 Pressure Gauge or the 6V-7830 Pressure Gauge can be used.
NOTICE
3. Set the engine speed to high idle with the transmission in neutral. Put the parking brake switch in the brake ON position. 4. Refer to table 1 in order to find the value for the "Steering Clutch Low Pressure". Find the value that corresponds to the application number of the machine that is being adjusted. 5. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 09. 6. Open the valve. Use the INCREMENT position ("+") and the DECREMENT position ("-") of the CLEAR switch to adjust the clutch pressure to the pressure that was found in Step 4. Note: The value in table 1 for the "steering clutch low pressure" may not be attainable. This is due to various conditions. Some of the conditions are no low pressure gauge, gauge hysteresis, and cold power train oil. Bring the pressures as close as possible to the specified value. The adjustments for "steering clutch low pressure" do not need to be exactly on the mark. 7. Close the valve or disconnect the gauge before submode 09 is exited.. Exit submode 09 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 10 And 11 - Inching Pedal Released Position And Inching Pedal Depressed Position
These procedures calibrate the released position and the depressed position of the inching pedal. Always perform the calibrations for both the released position and the depressed position.
View Image
Pgina 31 de 44
Illustration 3 Display Area (1) Submode identifier. (2) Accept status identifier.
g00597744
View Image
Illustration 4 Symbols That Are Shown On the Accept Status Identifier
g00597745
(3) Accepted Symbol. (4) Accepted symbol. (5) Not Accepted Symbol. (6) Not Accepted
1. With the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 10. 2. Depress the inching pedal completely. Release the inching pedal slowly. 3. While the inching pedal is released, press the CLEAR switch to the DECREMENT ("-") position in order to store the calibration value for the released position. While the switch is pressed, the accept status identifier (2) will briefly show the accepted symbol (4) or the not accepted symbol (6). Observe the accept status identifier (2) when the switch is pressed. Expected Result: The accepted symbol (4) or the not accepted symbol (6) shows on the accept status identifier. Results:
The accepted symbol (4) was showing. Proceed to 4. The not accepted symbol (6) was showing. Check that the inching pedal is completely released. Repeat step 3. If the not accepted symbol (6) is shown or if a CID 0573 FMI 08 diagnostic code is present, use the "Component Data Display Mode" in order to
Pgina 32 de 44
check the range of the inching pedal position sensor. The acceptable range is listed in the "Component Data Display Mode" section of this manual. The CID 0573 FMI 08 procedure may need to be performed. 4. Press the scroll switch in order to enter submode 11. 5. Depress the inching pedal completely by using normal effort to hold the pedal in the depressed position. Do not press hard on the pedal. While the pedal is held in the depressed position, press the CLEAR switch to the DECREMENT ("-") position in order to store the calibration value for the depressed position. When the switch is depressed, the accept status identifier (2) will briefly show accepted symbol (4) or not accepted symbol (6). Observe the accept status identifier (2) when the switch is pressed. Expected Result: The accepted symbol (4) or the not accepted symbol (6) shows on the accept status identifier. Results:
Accepted symbol "4" was showing. The calibration of the inching pedal is complete. Exit the "inching pedal calibration mode" by using the scroll switch. The MODE switch can also be used to exit the calibration. Not accepted symbol "6" was showing. Determine if the inching pedal is completely depressed. Repeat step 5. If not accepted symbol "6" is shown or if a CID 0573 FMI 08 diagnostic code is present, use the "Component Data Display Mode" section of this manual. The CID 0573 FMI 08 procedure may need to be performed.
Submode 12 And 13 - Service Brake Pedal Released Position And Service Brake Pedal Depressed Position
These adjustments modes are used to calibrate the released position and the depressed position of the service brake pedal. Always perform both released and depressed position calibrations. Note: This calibration applies to the D5N and D6N only. The service brake pedal sensor values must be within the following limits to complete the calibration procedure. If it is outside of these limits a service brake pedal sensor calibration fault will be active CID/FMI 0468-13.
Brake pedal released calibration --> sensor duty cycle between 10% and 33% Brake pedal depressed calibration --> sensor duty cycle between 40% and 62% Brake pedal range --> sensor duty cycle delta between 22% and 36% (Change in value between released calibration and depressed calibration)
If the service brake pedal sensor value is 5.5% duty cycle lower than the calibrated released position or 5.5% duty cycle higher than the calibrated depressed position, a service brake pedal sensor calibration fault will be active CID/FMI 0468-13. The service brake pedal sensor duty cycle must be between 8% and 64% duty cycle. If the sensor is outside of these limits a service brake pedal sensor out of range fault will be active CID/FMI 0468-
Pgina 33 de 44
08 and a service brake pedal sensor calibration fault will be active CID/FMI 0468-13. If a short circuit to battery diagnostic condition occurs on the secondary brake dump valve circuit before the service brake pedal position sensor value has reached (Brake pedal released calibration value + 17%), a secondary brake solenoid short circuit to battery diagnostic will be active CID/FMI 0722-03. This may be caused by a secondary brake switch that is closed when the service brake pedal position sensor indicates that the secondary brake switch should be open. If a short circuit to battery diagnostic condition does not occur on the secondary brake dump valve circuit (this is how the ECM "reads" the status of the service brake pedal switch) before the service brake pedal position sensor value has reached (Brake pedal depressed calibration value - 1%), a Secondary brake switch invalid diagnostic will be active CID/FMI 0298-02. This may be caused by a secondary brake switch that is open when the service brake pedal position sensor indicates that the secondary brake switch should be closed. This fault will stay active until the service brake pedal switch activation has been detected at the proper service brake pedal position (based on service brake pedal position sensor value).
The service brake pedal sensor must calibrate within the proper range of values. The service brake pedal sensor must operate within the proper range of values. The service brake pedal switch must not close before the sensor reaches the proper range of values. The service brake pedal switch must close before the service brake pedal position exceeds the proper range of values.
View Image
Illustration 5 Display Area (1) Submode identifier. (2) Accept status identifier.
g00597744
View Image
Pgina 34 de 44
Illustration 6 Symbols That Are Shown On the Accept Status Identifier
g00597745
(3) Accepted Symbol. (4) Accepted symbol. (5) Not Accepted Symbol. (6) Not Accepted
Table 4 Sub mode Calibration Parameter Description Data Right side = % Duty Cycle Left side = submode Right side = % Duty Cycle Left side = submode Depressed Released = Range (change in duty cycle) Service Brake Pedal Calibration Limits
12
Brake pedal released position
10 % < Released < 34 %
13
Brake pedal depressed position
39 % < Depressed < 63 %
Brake pedal travel range
21 % < Range < 37 %
Brake pedal switch range (switch must inside this range)
Releases position + 16 % < SW closure < Depressed - 1 %
1. Using the 4C-8195 Control Service Tool, enter "Steering/Braking Calibration Mode". Then, enter submode 12. 2. Depress the service brake pedal completely. Release the service brake pedal slowly. 3. While the service brake pedal is released, press the CLEAR switch to the DECREMENT ("-") position in order to store the calibration value for the released position. When the switch is pressed, the accept status identifier (2) will briefly show the accepted symbol (4) or the not accepted symbol (6). Observe the accept status identifier (2) when the switch is pressed. Expected Result: The accepted Symbol (4) or the not accepted symbol (6) shows on the accept status identifier (2) . Results:
The accepted symbol (4) was showing. Proceed to Test Step 4.
Pgina 35 de 44
The not accepted symbol (6) was showing. Check that the service brake pedal is completely released. Repeat step 4. If not accepted symbol (6) is shown or if a CID 0468 FMI 08 diagnostic code is present, use the "Component Data Display Mode" in order to check the range of the service brake pedal position sensor.
4. Press the scroll switch in order to enter submode 13. 5. Depress the service brake pedal completely by using normal effort to hold the pedal in the depressed position. Do not press hard on the pedal. While the pedal is held in the depressed position, press the CLEAR switch to the DECREMENT ("-") position in order to store the calibration value for the depressed position. When the switch is depressed, the accept status identifier (2) will briefly show accepted symbol (4) or not accepted symbol (6). Observe the accept status identifier (2) when the switch is pressed. Expected Result: The accepted symbol (4) or the not accepted symbol (6) shows on the accept status identifier. Results:
The accepted symbol "4" was showing. The calibration of the inching pedal is complete. Exit the "service brake pedal calibration mode" by using the scroll switch. The MODE switch can also be used to exit the calibration. The not accepted symbol "6" was showing. Determine if the service brake pedal is completely depressed. Repeat step 5. If not accepted symbol "6" is shown or if a CID 0468 FMI 08 diagnostic code is present, use the "Component Data Display Mode" in order to check the service brake pedal sensor.
Submode 20 - Set Forward High Speed Lockout

This submode sets the highest speed that is obtainable when the machine is in forward. Note: The transmission calibration mode for the D5M, D6M, D6R, and the D7R is Mode Number 6. The mode for the D6R Series II, D7R Series II, and the D8R Series II is Mode Number 7.
Procedure
1. With the 4C-8195 Control Service Tool, enter "Transmission Calibration Mode". Then, enter submode 20. 2. Use the INCREMENT position ("+") and the DECREMENT position ("-") of the CLEAR switch to select the desired maximum speed (F2 or F3). 3. Exit submode 20 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 21 - Set Reverse High Speed Lockout

This submode sets the highest speed that is obtainable when the machine is in reverse. Note: The transmission calibration mode for the D5M, D6M, D6R, and the D7R is Mode Number 6. The mode for the D6R Series II, D7R Series II, and the D8R Series II is Mode Number 7.
Pgina 36 de 44
Procedure
1. With the 4C-8195 Control Service Tool, enter "Transmission Calibration Mode". Then, enter submode 21. 2. Use the INCREMENT position ("+") and the DECREMENT position ("-") of the CLEAR switch to select the desired maximum speed (R2 or R3). 3. Exit submode 21 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submode 22 - Transmission Direction Lever Position Sensor Calibration

This submode sets the NEUTRAL position for the position sensor of the transmission direction control lever. The ECM monitors the sensor signal as the lever is moved in and out of NEUTRAL at least four times. When three dashes are showing in the display area, the calibration is complete. A flashing letter will normally be displayed. The procedure should be performed when the sensor has been replaced. During this calibration, error codes ("EXX") can occur. The error codes appear in the display area if there is a problem with the conditions for the calibration or if there is a problem with the results of the calibration. The error codes that can appear are listed below: E02 - The Engine Speed is Not Zero. E03 - The Sensor Calibration is faulty. 1. Exit the "transmission calibration mode". 2. Return to the "transmission calibration mode" and repeat the procedure. 3. If the error code is still present, replace the sensor. 4. Exit the "transmission calibration mode". 5. Return to the "transmission calibration mode" and repeat the procedure. 6. If the error code is still present, replace the detent assembly. 7. Exit the "transmission calibration mode". 8. Return to the "transmission calibration mode" and repeat the procedure. E08 - The diagnostic code for CID 0299 (sensor) is Active. Correct the problem. E09 - The Machine Speed is Not Zero.
Procedure
Note: The steps for this procedure must be performed exactly. The steps must be performed in sequence. This procedure can terminate if any unexpected functions are activated or if a diagnostic
Pgina 37 de 44
code is present. DO NOT change any switch positions. DO NOT move any levers. DO NOT depress any pedals. If there is a problem with the conditions for the calibration or if there is a problem with the results of the calibration, an error code ("EXX") will appear in the display area. 1. Place the transmission direction control lever in the NEUTRAL position. 2. With the 4C-8195 Control Service Tool, enter "Transmission Calibration Mode". Then, enter submode 22. 3. Watch the display area of the Caterpillar Monitoring System. The letter "F" should be FLASHING. Move the lever to the FORWARD position. The lever might need to be returned to the NEUTRAL position and the FORWARD position several times in order to stop the letter "F" from flashing. Note: If the conditions for setup are not correct, the flashing letter "F" is NOT shown in the display area. An error code ("EXX") will appear. The calibration will not run until all necessary conditions are met or error codes are corrected. Correct the error code and restart these procedures. 4. Now, the letter "N" should be FLASHING. Move the lever to the NEUTRAL position. The lever may need to be returned to the FORWARD position and the NEUTRAL position several times in order to stop the flashing letter "N". 5. Now, the letter "R" should be FLASHING. Move the lever to the REVERSE position. The lever may need to be returned to the NEUTRAL position and REVERSE position several times in order to stop the flashing letter "R". 6. Continue moving the lever to the position that matches the FLASHING letter. When the display area shows three dashes, the calibration is complete. 7. Exit submode 22 by scrolling to the next submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Submodes 31 to 35 and 40 - ECPC Clutch Calibrations

The power train ECM includes two calibration procedures for the transmission clutches on machines that have Electronic Clutch Pressure Control (ECPC).
The "Clutch Engagement Pressure Calibration" sets the electrical current of each clutch solenoid in order to obtain the correct pressure of each transmission clutch. The "Clutch Fill Calibration" sets the parameters for the transmission clutch fill. This calibration will affect the quality of the shifting of the transmission.
The Transmission System needs to be calibrated if any of the following events have occurred:
A clutch solenoid valve has been replaced. A clutch solenoid valve has been substituted. A clutch solenoid valve has been cleaned. A different power train ECM has been installed.
Pgina 38 de 44
A transmission clutch has been rebuilt. Shifting is harsh.
When the calibrations are performed for machines that have the ECPC, error codes ("EXX") can occur. The error codes appear in the display area if there is a problem with the conditions or if there is a problem with the results of the calibration. The possible error codes are listed within each of the following procedures.
Submode 31 - Clutch 1 Engagement; Submode 32 - Clutch 2 Engagement; Submode 33 - Clutch 3 Engagement; Submode 34 - Clutch 4 Engagement; Submode 35 Clutch 5 Engagement
Table 5 Engagement Pressure Specifications For Transmission Clutches Sales Model Clutch 1 2205 kPa (320 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2586 kPa (375 psi) Clutch 2 2415 kPa (350 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2586 kPa (375 psi) Clutch 3 2550 kPa (370 psi) 2690 kPa (390 psi) 2550 kPa (370 psi) 2690 kPa (390 psi) 2550 kPa (370 psi) 2550 kPa (370 psi) 2690 kPa (390 psi) Clutch 4 2550 kPa (370 psi) 2690 kPa (390 psi) 2550 kPa (370 psi) 2690 kPa (390 psi) 2550 kPa (370 psi) 2550 kPa (370 psi) 2690 kPa (390 psi) Clutch 5 2480 kPa (360 psi) 2415 kPa (350 psi) 2205 kPa (320 psi) 2205 kPa (320 psi) 2550 kPa (370 psi) 2205 kPa (320 psi) 2205 kPa (320 psi)
D5M PSTC
(1)
D6M PSTC D6R Series II D6R PSTC D7R Series II D7RPSTC
D5M PSDD (2) D6R Series II D6R PSDD D8R Series II D8R PSTC
(1) (2)
PSTC = Power Shift Torque PSDD = Power Shift Direct Drive.
Table 6 Tools Needed Part
Pgina 39 de 44
Number 4C-8195 8T-0855
Description Control Service Tool 4150 kPa (600 psi) Pressure Gauge
Quantity 1 1
View Image
Illustration 7 g00859862 Identification of the Solenoid Valves for Clutches on the machines that have the ECPC
The life of the transmission is affected when the pressure for clutch engagement is correct. These submodes set the pressure for the engagement of each clutch. The mechanic must adjust the electrical current that is sent to each clutch solenoid valve in order to obtain the specified pressure for the engagement of the clutch. This calibration should be performed prior to performing the
Pgina 40 de 44
"clutch fill calibration" (submode 40). During this calibration, error codes ("EXX") can occur. The error codes appear in the display area if there is a problem with the calibration or if there is a problem with the results of the calibration. The error codes that can appear are listed below: E01 - There is a problem with the Active Clutch Solenoid or the Speed Sensor. E04 - The Transmission Direction Control Lever is Not In Neutral. E05 - The Transmission Oil Temperature is Below the Threshold of 40 C (104 F) or there is a problem with the Transmission Oil Temperature Sensor. E06 - The Engine Speed is Below the Threshold of 1500 RPM. E07 - The Parking Brake Is Not On. E08 - CID 0299(sensor) is Active. Correct the problem. E09 - The Machine Speed is Not Zero. E10 - The Service Brake Pedal is Pressed. Procedure Note: The steps of this procedure must be performed exactly. The Steps of this procedure must be performed in sequence. This procedure can terminate if any unexpected functions are activated or if a diagnostic code is present. DO NOT change any switch positions. DO NOT move any levers. DO NOT depress any pedals. If there is a problem with the calibration or if there is a problem with the results of the calibration, an error code ("EXX") will appear in the display area. 1. If a new clutch solenoid valve was installed, shift the transmission at least 12 times into a gear that uses the solenoid valve. Allow sufficient time for the corresponding clutch to be fully pressurized. 2. Warm the transmission oil to at least 40 C (104 F). The "Component Data Display Mode" (Mode Number 7) can be used to monitor the temperature of the transmission oil. The CID number is 0177. 3. Place a pressure gauge on the clutch that needs to be calibrated. A gauge that can measure 3500 kPa (508 psi) is desired. 4. Place the transmission direction control lever in the NEUTRAL position. 5. Place the parking brake switch in the ON position. The transmission will shift to NEUTRAL. Then, the transmission will shift to First Speed. 6. Set the engine speed to high idle. 7. With the 4C-8195 Control Service Tool, enter "Transmission Calibration Mode" (Mode 6) for the D5M, D6M, D6R and the D7R. The mode for the D6R Series II, D7R Series II, and the D8R Series II is Mode Number 7. Then, enter the submode that corresponds to the clutch that is being calibrated.
Pgina 41 de 44
Submode 31 - Clutch 1 Engagement Submode 32 - Clutch 2 Engagement Submode 33 - Clutch 3 Engagement Submode 34 - Clutch 4 Engagement Submode 35 - Clutch 5 Engagement
8. If all the conditions are correct for calibration, the specified pressure for the engagement for the particular clutch is shown in the display area. The value that is shown is in units of ten kPa. For the actual value, multiply the value that is showing by 10. Record the value. In the remaining Steps, adjustments are made so that the pressure is the actual reading for pressure from the pressure gauge. The pressure that is specified in the procedure is also listed in the "Engagement Pressure Specifications" table. Note: If the conditions for setup are not correct, the pressure is NOT shown in the display area. An error code ("EXX") appears instead of the pressure value. The calibration will not run until all error codes are corrected. Correct the error code and restart these procedures. 9. When the pressure is showing on the display, move the transmission direction control lever to the FORWARD position. This pressurizes the clutch that is being calibrated. 10. The display will change. Now, the display shows a number that corresponds to the electrical current of the particular solenoid valve. The INCREMENT position ("+") and the DECREMENT position ("-") of the CLEAR switch can now be used to adjust the electrical current of the solenoid valve. The solenoid valve controls the pressure of the engagement of the clutch. While the pressure gauge is monitored, use the CLEAR switch in order to adjust the pressure. Adjust the pressure until the value that is on the pressure gauge matches the pressure that was specified in Step 8. 11. Move the transmission direction control lever to the NEUTRAL position. The calibration is complete. 12. Use the SCROLL switch to go to the submode that corresponds to the next clutch that needs to be calibrated. The SCROLL switch may also be used to go to the "Clutch Fill Calibration" ( submode 40). To exit Transmission Calibration Mode, use the MODE switch.
Submode 40 - Clutch Fill

Table 7 Tools Needed Part Number 4C-8195 Description Control Service Tool Quantity 1
The quality of the shifting of the transmission can be affected by the calibration of the clutch fill.
Pgina 42 de 44
The calibration procedure is automatic. The "clutch engagement calibration" (submodes 31 through 35) should be performed prior to performing the "clutch fill calibration". During this calibration, error codes ("EXX") can occur. The error codes appear in the display area if there is a problem with the calibration or if there is a problem with the results of the calibration. The error codes that can appear are listed below: E01 - There is a problem with an Active Clutch Solenoid Or a Speed Sensor. E04 - The Transmission Direction Control Lever is Not In Neutral. E05 - The Transmission Oil Temperature is Below the Threshold of 68 C (154 F) or the Transmission Oil Temperature Sensor is Faulty. E06 - The Engine Speed is Below the Threshold of 1500 RPM. E07 - The Parking Brake Is Not On. E08 - CID 0299 (sensor) is Active. Correct the problem. E09 - The Machine Speed is Not Zero. E10 - The Service Brake Pedal is Pressed. E21 - Clutch 1 is At A Limit. E22 - Clutch 2 is At A Limit. E23 - Clutch 3 is At A Limit. E24 - Clutch 4 is At A Limit. E25 - Clutch 5 is At A Limit. For error codes E21, E22, E23, E24, or E25 the calibration software will select values that do the best job possible, but the error indicates something is wrong with either the calibration conditions or the control system. Things to check for E21 through E25 are:
The oil and the transmission is fully warmed for the calibration. The valves are correctly torqued when the machine is cool. The seals are not worn. The clutch is not worn beyond the allowable range. The valve is not damaged. If a new valve was installed, shift the tractor into a gear that uses the new valve at least 12 times before beginning the procedure. Check that the priority valve solenoid is off.
Pgina 43 de 44
Once problems are fixed, run the "clutch fill calibration" (submode 40) again. Procedure Note: The steps of this procedure must be performed exactly. The Steps of this procedure must be performed in sequence. This procedure can terminate if any unexpected functions are activated or if a diagnostic code is present. DO NOT change any switch positions. DO NOT move any levers. DO NOT depress any pedals. If there is a problem with the calibration or if there is a problem with the results of the calibration, an error code ("EXX") will appear in the display area. 1. The "clutch engagement calibration" (submodes 31 through 35) should be performed prior to performing the "clutch fill calibration". 2. If a new clutch solenoid valve was installed, shift the transmission at least 12 times into a gear that uses the solenoid valve. Allow sufficient time for the corresponding clutch to be fully pressurized. 3. Warm the transmission oil to at least 68 C (154 F). The "Component Data Display Mode" can be used to monitor the temperature of the transmission oil. The mode for the D6R Series II, D7R Series II, and the D8R Series II is Mode Number 8. The mode for the D5M, D6M, D6R, and the D7R is Mode Number 7. The CID number is 0177. Operate the machine or allow the transmission to spin in NEUTRAL in order to ensure that the transmission is fully warmed. 4. Place the transmission direction control lever in the NEUTRAL position. 5. Place the parking brake switch in the ON position. The transmission will shift to NEUTRAL and to First Speed. 6. On machines that have the Power Shift Torque Converter, set the engine speed to 1600 RPM. On machines that have the Power Shift Direct Drive, set the engine speed to 2000 RPM. 7. With the 4C-8195 Control Service Tool, enter "Transmission Calibration Mode" (Mode 6). Then, enter submode 40. 8. If all the conditions are correct for calibration, "0's" will move across the display area. Note: If the conditions for setup are not correct, "0's" are NOT shown in the display area. An error code ("EXX") appears. The calibration will not run until all error codes are corrected. Correct the error code and restart the procedures. 9. When "0's" are moving across the display, move the transmission direction control lever to the FORWARD position. The "clutch fill calibration" will begin. 10. The display changes. The display now shows the number of the active clutch (1 through 5). The calibration automatically changes in order to perform the calibration for each clutch. Note: During the calibration, there are many clutch fills occurring. Remain seated. Vibration and noise will be present . If any of the conditions for setup are not followed during the calibration, then the calibration will be stopped and a corresponding error code ("EXX") will be shown. Correct the error code and restart the procedures. 11. When the calibration is completed successfully, "---" will be shown on the display. An error code may also be displayed. The error code indicates that the calibration had a problem.
Pgina 44 de 44
12. Operate the machine in order to check the quality of the shifting of the transmission. 13. Exit submode 40 by scrolling to another submode with the SCROLL switch. The MODE switch can also be used to exit the calibration.
Copyright 1993, 2004 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.
Tue Jun 1 19:07:29 EST 2004

CalibrationXmsn - Testing Adjusting

Uploaded by

Copyright:

Available Formats

CalibrationXmsn - Testing Adjusting

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CalibrationXmsn - Testing Adjusting

Uploaded by

Copyright:

Available Formats

Service Information System

Testing and Adjusting

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

2275 30 kPa (330 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)

2275 30 kPa (330 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)

2275 30 kPa (330 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi) 35 20 kPa (5 3 psi)

2275 30 kPa (330 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)

2240 30 kPa (325 4 psi) 2240 30 kPa (325 4 psi) NA

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

2275 30 kPa (330 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)

2275 30 kPa (330 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)

2275 30 kPa (330 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)

572R D8R Series II

2240 30 kPa (325 4 psi) NA

35 20 kPa (5 35 20 kPa (5 3 psi) 3 psi) NA 35 20 kPa (5 3 psi)

Accessing Calibration And Display Modes Of The Monitoring System

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

Table 2 Calibration Modes Parking Brake Status Submode (1) Number

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

Component Data Display Mode

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

Performing Calibrations With the ET Service Tool

Data Format Left character = left steering lever

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

RPM O = contact open C = contact closed

Transmission (Direction) Lever Position Sensor

Implement Lockout Switches

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System

Direction Switch (Reverse)

0671 0672 0673 0674

0 to 3000 = display range

0676 0677 0681

% Duty Cycle (1) % Duty Cycle (1) Unitless command value

https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/medias ... 01/06/2004

Service Information System