Scribd
Upload
84 views4 pages

Vidya Jyothi Institute of Technology: Guide

This document describes a project to develop a home appliance monitoring and controlling system using hand gesture recognition. An accelerometer sensor would detect gestures and send signals via RF transmitter to an RF receiver connected to a microcontroller. The microcontroller would process the signals and control appliances like lamps, fans, and motors by activating relays. The system aims to allow users to control appliances in their home through simple hand gestures without needing a remote control. It could help people with disabilities operate devices more easily.

Uploaded by

MadhanMohanReddy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
84 views4 pages

Vidya Jyothi Institute of Technology: Guide

This document describes a project to develop a home appliance monitoring and controlling system using hand gesture recognition. An accelerometer sensor would detect gestures and send signals via RF transmitter to an RF receiver connected to a microcontroller. The microcontroller would process the signals and control appliances like lamps, fans, and motors by activating relays. The system aims to allow users to control appliances in their home through simple hand gestures without needing a remote control. It could help people with disabilities operate devices more easily.

Uploaded by

MadhanMohanReddy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

VIDYA JYOTHI INSTITUTE OF TECHNOLOGY

Aziz Nagar Gate, C.B. Post, Hyderabad 500 075 Department of Electronics and Communication Engineering

Home appliances monitoring and controlling system using a Gesture


Name Id. No. Email Id Mobil e no. B. Arun kumar 10911A0412 banalaarunkumar29@gmail. com 9550243173 CH. Anil kumar 10911A0426 [email protected] 8143228086 G. Sandeep Goud 10911A0436 [email protected] 9177321699

GUIDE: PRASANNA LAXMI

ABSTRACT

OBJECTIVE:
The main aim of this project is to develop a system, which uses Gesture Control technology that keeps monitoring of the various appliances, and will control the operation of these appliances with respect to the gesture done by your hand.

INTRODUCTION:
The goal of the project is to develop a system, which uses Accelerometer Sensor to detect motion and controls various appliances of the home, which executes with respect to the gesture. For utilization of appliances the new concept has been thought to manage them by using Accelerometer, which enables the user to control switching of domestic appliances. The ranges of appliances that can be controlled through accelerometer are many in numbers. Some of them are as follows and this depends upon the usage priority of the appliances i.e. parking Lights, Music System or other electrical / electronic appliances. .

TECHNOLOGY: Accelerometer: Accelerometer is a sensor which detects the motion in x,y,z directions and gives the outputs in those axis. So the motion in x direction can be measured from the output of x output pin on the accelerometer and once the motion is detected the microcontroller can be programmed such that a particular action can be performed. RF Transmitter and Receiver : The output received from the accelerometer can be transmitted by the RF transmitter to the receiver which can be used to control the loads through the relays.

BLOCK DIAGRAM:

RF Receiver

LCD

RELAY1 MICRO CONTROLLER

LAMP1

Accelerometer

RELAY2 DRIVERS

LAMP2 DC FAN

DRIVERS

DC MOTOR

POWER SUPPLY:
Step Down Transformer Bridge Rectifier Filter Circuit Regulator section

SOFTWARE AND HARDWARE TOOLS: Software Tools: 1. Embedded C 2. Keil IDE 3. Uc-Flash Hardware Tools:

1. Micro controller 2. Power supply 3. LCD 4. Accelerometer 5. RF Transmitter/Receiver 6. Relays 7. Drivers 8. Appliances

APPLICATIONS:
1. We can use this system in automation of industries. 2. Used for Industrial security purpose.

RESULT:
By using this project we can implement an automation system in a home to control different devices which reduces a lot of manual power and correspondingly provides the flexibility and reliability.

Controlling the home appliances and electronics gadgets through an Infrared remote control is now in general. But the same controlling tasks can be done more easily. Primary motive of proposing the new system of hand gesture remote control is to remove the need to look in to the hand held remote and to search for a specific key for specific function. This paper presents a novel system to control home appliances through hand gesture as a remote control device. The system will referred to as Handmote in this paper. It uses real time image processing for hand gesture recognition in infrared vision using Blobscanner [1] library and microcontroller development board , Arduino[2]. This paper proposes a possible solution to control the gadgets for physically challenged and blind people.

You might also like