VS 101.51

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

www.vibrasens.

com

ICP Accelerometer Model 101


Premium, Top connector
Main Characteristics
Annular shear mode
10, 50, 100, 500 mV/g version availbale
-55C to 150 C (-67F to 302F)
Dual case isolation with Faraday shield
Submersible version (150 metres) with associated IP68 over-

molded cable
life time hermetic sealing warranty (M12/Mil glass seal con-

nector)
Compare to obsolete compression design, annular shear

piezoelectric sensors feature better frequency response,


improved base strain, lower noise, smaller size, thermal transient imunity and insensitivity to cable motion.
Annular shear mode is also less susceptible to transverse vibrations and better immune to electronic saturation at high frequency.
80 g dynamic range (thanks to exceptional bias stability) at elevated temperatures.
Resistant to shock (magnet mounting) thanks to Jfet transistor
input.
ESD and reverse wiring protection.
The glass seal hermetic connector protects the piezoelectric
disc and the electronic from harmful environmental influences,
significantly increasing their reliability and lifetime. Associated
with low cost IP68 overmolded M12 cable assembly it is a perfect solution for submersible application down to 150 metres.
Sensors with epoxy seal will always leak after few temperature
cycles.
M12 connector offers compatibility with numerous sensors used
in automation. M12 overmolded cable assemblies are available
from many cable manufacturers around the world. Mil cordset
are expensive because they are only available from vibration
sensor manufacturer.

Description
The hermetic sealed industrial piezoelectric accelerometer model 101
is design to monitor the vibration in harsh industrial environment. It
uses the industry standard ICP / IEPE / LIVM 2-wire voltage
transmission technique with a 4 mA standard constant current supply.
Signal ground is isolated from the mounting surface and outer case to
prevent ground loops. Faraday shielding will limit sensitivity to EMC
to a minimum. Annular shear mode design will prevent from thermal
transient and from spurious signal from high transverse vibrations.
Low noise electronic and a temperature compensated design will
give you accurate result over the complete temperature range. Large
choice of frequency range will help to fit almost every customer requirements. Low frequency accelerometers (A=9) incorporate a lowpass filter within the conditioning electronic. This filter attenuates
the sensor mechanical resonance and the associated distortion and
overload.

Typical applications
Vibrations measurement in the rugged environments of industrial machinery monitoring. High frequency version monitor the vibration
on roller bearing, pumps cavitation, .... Medium frequency version
monitor overall vibration on pumps, motors, fans, ... Low frequency
model is used in the petrochemical, machine tool, and paper industries for monitoring of slow speed agitators, cooling towers, ... High

Model 101.51-A-2 with overmolded


IP 68 submersible M12 cable assembly
temperature version is typically used where extra temperature protection is needed, such as the dryer section of a paper machine.

Ordering information model 101


To order, specify model number, options, accessories and suffix :

101.51- AA - B - TT - MM - HH - YY
AA : Sensitivity
3 : 10 mV/g 5 % (high frequency)
3D : 10 mV/g 10 % (high frequecy)
5 : 50 mV/g 5 % (high frequency)
5D : 50 mV/g 10 % (high frequency)
6 : 100 mV/g 5 % (medium frequency, general purpose)
6D : 100 mV/g 10 % (medium frequency, general purpose)
6Q : 100 mV/g 15 % (medium frequency, general purpose)
9 : 500 mV/g 5 % (low frequency)
9D : 500 mV/g 10 % (low frequency)
Available suffix : N, negative polarity
B : Connector
1 : MIL-C-5015, glass seal
2 : M12 glass seal
B(CC-DD) Integral cable
5 (CC-DD) : Integral cable
7 (CC-DD) : Integral cable with sstl overbraid protection
8 (CC-DD) : Integral cable with stainless steel protection conduit
5, 7, 8 : epoxy seal.
CC : Cable Type
01 : *Polyurethane twisted pair cable (90C)
02 : *Teflon FEP twisted pair Cable (200C)
03 : Radox twisted pair cable (120C, halogen free)
DD : length in metre
TT : Temperature output.
omitted : no temperature output
T0 : 10 mV/C. (range +2 to +120C)
Not available with Mil-C-5015 2 pins connector
MM : Machine thread
omitted : no mounting stud will be shipped with the sensor.
M6 : M6x1
M7 : 1/4 28 UNF 2A
M8 : M8x1.25
HH : Housing thread

Industrial Piezoelectric Vibration Sensor

Competitive advantage

www.vibrasens.com

H6 or omitted : M6x1 (China, Europe, India, South America, ...)


H1 : M16x2 (quick mouting + 120 positioning) (Not stocked)
H2 : Quick fit mounting (Not stocked)
H7 : 1/4 28 UNF-2A. (U.S.A., UK, ...)
YY : Agency Approval
omitted : no agency approval
Y1 : Atex approved (July 2010)
Special Engraving :
Add ZXX at the end of the part number.
XX is a number supplied by VibraSens

In stock Model
Industrial Piezoelectric Vibration Sensor

Metric connector
101.51-6D-2-M6 100 mV/g 10% general purpose version
101.51-6-2-M6
100 mV/g 5 %general purpose version
101.51-9-2-M6
500mV/g 5 %low frequency version
101.51-3-2-M6
10 mV/g 5 %high frequency version
101.51-6D-2-T0-M6 100 mV/g 10 %with temperature output
American/UK connector
101.51-6D-1-M7 100 mV/g10 % general purpose
101.51-6D-1-H7-M7 100 mV/g10% (1/428UNF housing thread)
101.11-6-1-M7
100mV/g5 % high temp. version (150C)
101.51-9-1-M7
500mV/g5 % low frequency version
101.51-3-1-M7
10 mV/g 5 % high frequency version

Polarity......................................................................................(fig. 1) Suffix dependant


Linearity........................................................................................................... 1% Max
Warm up time (Typical)
A=3X, 6X......................................................................................................... < 1Sec
A=9X............................................................................................................. < 10 Sec
Option T0 (only available if sensor is powered)
Output (between - and Temp)....................................... Vout=10mV/C * Temp.(C)
. ..............................................................................................................0VDC at 0C
Range..................................................................................................... +2 to 120C

Electrical
Electrical Grounding........................................................Isolated from machine ground
................................................................................... Internal Faraday shielding (fig. 1)
Isolation(Case to shield)............................................................................. 100 M Min
Capacitance to ground.................................................................................... 70 pF Nom
Output impedance............................................................................................ 50 Nom
DC output bias, 4mA supply..........................................................12 VDC Nom (Fig 2)
Residual noise (24C) : A=3X
1 Hz to 25 kHz.......................................................................................... 300 ug rms
1 Hz.................................................................................................................... 30 ug
Residual noise (24C) : A=6X
1 Hz to 25 kHz ......................................................................................... 300 ug rms
1 Hz................................................................................................................... 30 ug
Residual noise (24C) : A=9X
1 Hz to 25 kHz ........................................................................................... 25 ug rms
1 Hz................................................................................................................... 2.4 ug
Power requirements Constant current : +2 to +10mA DC
............................................................................................... Voltage : +22 to +28 VDC
Protection : Overvoltage............................................................................................ Yes
: Reverse polarity ...................................................................................... Yes

Environmental

Available Model with short lead time (1 week)


101.51-6D-5(01-Length)-M6 integral polyurethance cable
101.51-6D-6(02-Length)-M6 integral 200C sstl overbraided teflon

cable
Old Part number compatibility
101.21-6 is replaced by 101.51-6D
B=3 : M12 epoxy seal connector is obsolete. B=2 should be ordered.

Ordering example :
101.51-6D-2-M6

101.51-6D-7(02-05)-M6

Premium accelerometer, 100mV/g,


M12 glass seal connector
Premium accelerometer, 5 metres Inte
gral teflon cable with Stainless steel
overbraid.

Specifications (24C)
Dynamic
Sensitivity (101.01)
A=3 ......................................................................................................10 mV/g 5%
A=3D .................................................................................................10 mV/g 10%
A=6 ....................................................................................................100 mV/g 5%
A=6D ...............................................................................................100 mV/g 10%
A=6Q ...............................................................................................100 mV/g 15%
A=9 ....................................................................................................500 mV/g 5%
A=9D ...............................................................................................500 mV/g 10%
Frequency response 101.01 & 101.51 (fig. 4a, 4b)
A=3X ..................................................................................... 10 % : 1 to 11000 Hz
. ............................................................................................ 3 dB : 0.5 to 16000 Hz
A=6X .......................................................................................10 % : 1 to 9000 Hz
. ............................................................................................ 3 dB : 0.5 to 14000 Hz
A=9X ....................................................................................10 % : 0.4 to 1600 Hz
. .............................................................................................. 3 dB : 0.2 to 3700 Hz
Mounted Resonant frequency
A=3X.......................................................................................................35 kHz Nom
A=6X.......................................................................................................25 kHz Nom
A=9X.......................................................................................................16 kHz Nom
Dynamic range
A=3X............................................................................................................. 500 g pk
A=6X............................................................................................................... 80 g pk
A=9X............................................................................................................... 10 g pk
Transverse response sensitivity (20Hz, 5g)..............................................................<5%
Temperature response................................................................................................fig3

Temperature, operating continuous : 101.01 & 101.51 (max. current =4mA)


A= 3X, 6X . ..................................................................-55 to 120 C (-65 to 250 F)
A=9X...............................................................................-55 to 90 C (-65 to 212 F)
Temperature, operating continuous : 101.11 (max. current =4mA)
A=6X, B=1 ....................................................................-55 to 150C (-65 to 302 F)
Humidity / Enclosure
B=1, 2................................................. Not affected, hermetically sealed, 1E-8torr.l/s
B=5, 7, 8........................................................................................IP68, epoxy sealed
Acceleration limit : Shock............................................................................5 000g peak
: Continuous vibration.......................................................500g peak
Base strain sensitivity...................................................................... 0.0002 g pk/u strain
Temp. transient sens. (3Hz, LLF, 20dB/dec)......................................................5 mg/C
Acoustic sensitivity (164 dBSP)........................................................................... 0.5 mg
Electromagnetic sens. (50Hz, 0.03 T)..................................................................... 0.2 g
Mean time between failure (MTBF)......................................................... 10 Years Nom
ESD Protection ................................................................................................... > 40 V
Safety................................................................................. EN 61010-1 and IEC 1010-1
EMC emission.........................................................................EN 50081-1, EN 50081-2
EMC immunity (1) ............................................................... EN 50082-1, EN 50082-2

Physical
Dimensions
B=1................................................................................................................... Fig. 1a
B=2...................................................................................................................Fig. 1b
B=5...................................................................................................................Fig. 1d
B=7................................................................................................................... Fig. 1e
B=8....................................................................................................................Fig. 1f
Design .............................................................................. Ceramic, annular shear mode
Weight with connector
A=3..............................................................................................80 gr Nom (2.8 Oz)
A=6 .............................................................................................85 gr Nom (3.0 Oz)
A=9 .............................................................................................95 gr Nom (3.4 Oz)
Connector
B=1................................................. MIL-C-5015 glass seal, Type MS3143 10SL-4P
B=2 . ......................................................................... M12 glass seal, IEC 60947-5-2
Material............................................................AISI 316L, DIN 1.4404 (Stainless steel)
Housing thread.......................................................................................................Fig 1h
Mounting torque (M6, M7, M8 suffix)............................................. 2,4 N.m (21 in-lbs)

Accessories, supplied
Calibration supplied
...................................................................................................Sensitivity (5g, 160 Hz)
.................................................................................................... No frequency response

Accessories, not supplied


Cable assembly B=1 (Mil connector)
Polyurethane cable........................................................... 10.01-B22-A01-05-Length
FEP Teflon cable.............................................................. 10.01-B22-A01-02-Length
Cable assembly B=2 (M12 connector)

www.vibrasens.com

Polyurethane cable .......................................................... 10.01-E02-A01-31-Length


FEP Teflon cable.............................................................. 10.01-E02-A01-02-Length
For more cable option see Model 10.01 (specific cable harness).

Internal
shield

Accessories, spares part

Case

Mounting Stud with HH=H6


M6 machine thread............................................................................. 191.01-06-06-1
1/4 28 UNF machine thread............................................................. 191.01-06-16-1
M8 mahine thread ............................................................................. 191.01-06-08-1

Master key
2

Standard Wiring color


With Mil-C-5015 cable assembly: + = Red // - = White // Temperature=black
With M12 cable harness: : + = Black // - = Blue // Temperature=White

Repair

Hex

Consult factory for replacement of connector in case of broken or bended pins. Repair
of electronic is not possible.

22

Receptacle
M12 IEC 6094752

21.3

Industrial Piezoelectric Vibration Sensor

[ .84 ]

(1) Guaranted if using accessories listed in this product datasheet only

M 12

Drawings
A

20

Master key
A

[ .79 ]

46.5

Case

[ 1.83 ]

Internal
shield

20
[ .79 ]
Hex

22

Receptacle
MILC5015G
21,3

Model Number

Pin 1

Pin 2

Pin 3

Pin 4

Standard, no option

NC

NC

(-)

(+)

T0 Option (10mV/C)

NC

(Temp)

(-)

(+)

[ .84 ]
5/8"24 UNEF2A

[ .79 ]

50.8

20

[ 2.00 ]

(NC) : Not connected


fig 1b : Outline drawing & Electrical layout, B=2 (M12 glass seal)

20
[ .79 ]

(+)

(-)

N/A

N/A

(N/A) : Not available


Fig 1a : Outline drawing & Electrical layout, B=1 (MIL-C-5015)

[ .79 ]

Standard, no option
T0 Option (10mV/C)

60

Pin B

[ 2.36 ]

Pin A

20

Model Number

20
[ .79 ]
Hex 22

CC=01, 02 (PU, Teflon)

White (-) / Red (+)

CC=03 (Radox)

White N1 (-) / White N2 (+)

CC=12 (Teflon) (1)

White (-) / Red (+) / Black (Temp.)

CC=13 (Radox) (1)

White N1 (-)/ White N2 (+) / / White N3 (Temp)

CC=31 (PU) (1)

Blue (-) / Black (+) / White (Temp.) / Brown (NC)

(1) T0 option (10mV/*C)


Fig 1d : Outline drawing & Electrical layout, B=5 (cable only)

www.vibrasens.com

20

10

10

-10

-10

Sensitivity deviation (%)

20

-20

-20
-50
(-58)

0
(32)

50
(122)

100
(212)

150
(302)

Temperature C

20
[ .79 ]
Hex 22

Fig 1e : Outline drawing B=7 (cable with overbraid)


electrical layout : See above B=5

40

40

30

30

20

20

10

10

-10

-10

-20
* Deviation
in (%) for f < 10kHz
in (dB) for f>10kHz

-30
-40
1

10

-20

A=3
A=6
A=9

-30
10k

100 Frequency (Hz) 1000

-40
50k

Fig 4a: Frequency response, amplitude




[ .276 ]

Option H7

Option H1

M 16 x2

1/4"28 UNF

7,5

7,5

[ .295 ]

[ .295 ]

6HQVLWLYLW\GHYLDWLRQ 

M 6

Standard

[ .236 ]

[ .236 ]

Detail of tapped hole






$
$
$











)UHTXHQF\ +]

Bias deviation (%)

Fig 1h : Housing thread, option H1, H2, H7

Fig 4b : Low Frequency response, amplitude

20

20

10

10

-10

-10

-20

-20
-50
(-58)

0
(32)

50
(122)

100
(212)

Temperature C (F)

Fig 2 : DC (Bias) deviation versus temperature

10

150
(302)



Sensitivity deviation (dB)

Sensitivity deviation (%) *

[ .79 ]

60

20

[ 2.36 ]

Industrial Piezoelectric Vibration Sensor

Fig 3 : Sensitivity deviation versus temperature

You might also like