Manual Da Placa W240HU-W250HUQ

V11.1.
11
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. December 2011
Trademarks
Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
EuP-Standby and Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode or standby mode:
Standby Mode < 2W Off Mode < 1W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters CE. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market. This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark. The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.
III
Preface
FCC Statement
(Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the service representative or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:

1. 2. This device may not cause interference. And This device must accept any interference, including interference that may cause undesired operation of the device.
IV
Preface
FCC RF Radiation Exposure Statement:

1. 2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Warning Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
Preface
IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19V, 3.42A or 18.5, 3.5A (65 Watts) minimum AC/DC Adapter.
This Computers Optical Device is a Laser Class 1 Product
VI
Preface
Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Dont drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer to any shock or vibration. Do not place it on an unstable surface. Do not place anything heavy on the computer.
2.
Keep it dry, and dont overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive heat or direct sunlight. Do not leave it in a place where foreign matter or moisture may affect the system. Dont use or store the computer in a humid environment. Do not place the computer on any surface that will block the Vents/Fan Intakes.
VII
Preface
3. 4. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and dont forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until you properly shut down all programs. Do not turn off any peripheral devices when the computer is on. Do not disassemble the computer by yourself. Perform routine maintenance on your computer.
5.
Take care when using peripheral devices.

Use only approved brands of peripherals. Unplug the power cord before attaching peripheral devices.
VIII
Preface
Power Safety
The computer has specific power requirements:
Only use a power adapter approved for use with this computer. Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one. When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire. Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices. Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power cord if you are wet. Do not use the power cord if it is broken. Do not place heavy objects on the power cord.
Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.
IX
Preface
Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.
Polymer batteries may experience a slight expansion or swelling, however this is part of the batterys safety mechanism and is not a cause for concern. Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
Preface
Battery Precautions
Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. Do not remove any batteries from the computer while it is powered on. Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. If you do not use the battery for an extended period, then remove the battery from the computer for storage. Recharge the batteries using the notebooks system. Incorrect recharging may make the battery explode. Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel. Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded. Keep the battery away from metal appliances. Affix tape to the battery contacts before disposing of the battery. Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturers instructions.
XI
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
When the power cord or AC/DC adapter is damaged or frayed. If the computer has been exposed to rain or other liquids. If the computer does not work normally when you follow the operating instructions. If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks). If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.
XII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure its latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you wont need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters. Put the notebook in its carrying bag and secure it with the bags straps. If youre taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices adapters and/or cables. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hardware and software. Make sure your documents are prepared.
Power Off Before Traveling Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
XIII
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, dont let it out of your sight. In some areas, computer theft is very common. Dont check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects. Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices. Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure its secure. Contents may shift and/or fall out when the compartment is opened. Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged. Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.
XIV
Preface
Developing Good Work Habits

Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:
Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position. Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary. Use a chair with a back and adjust it to support your lower back comfortably. Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working. Take periodic breaks if you are using the computer for long periods of time. Remember to: Alter your posture frequently. Stretch and exercise your body several times a day. Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XV
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.
Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:
Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time. Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long). Rotate desktop background images every few days. Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your service center.
XVI
Preface
Contents
Notice .................................................................................I EuP-Standby and Off Mode Power Consumption Statement: .................................................................................II FCC Statement ................................................................ IV FCC RF Radiation Exposure Statement: ......................... V Instructions for Care and Operation ..............................VII Power Safety ................................................................... IX Polymer Battery Precautions ........................................... X Battery Precautions ......................................................... XI Cleaning .........................................................................XII Servicing ........................................................................XII Travel Considerations .................................................. XIII System Map: LCD Panel Open - Model B ....................1-9 System Map: Model C - LCD Panel Open ..................1-10 LED Indicators .............................................................1-11 Hot Key Buttons - Model A Design I Only .................1-12 Keyboard - Model A ....................................................1-13 Keyboard - Model B ....................................................1-14 Keyboard - Model C ....................................................1-15 Function/Hot Key Indicators .......................................1-16 System Map: Front & Left Views - Models A & B .....1-17 System Map: Front & Left Views - Model C ..............1-18 System Map: Right & Rear Views - Models A & B ...1-19 System Map: Right & Rear Views - Model C .............1-20 System Map: Bottom View - Model A ........................1-22 System Map: Bottom View - Model B ........................1-23 System Map: Bottom View - Model C ........................1-24 Video Features .............................................................1-26 Power Options ..............................................................1-28
Quick Start Guide

Overview ........................................................................1-1 Advanced Users .............................................................1-2 Beginners and Not-So-Advanced Users ........................1-2 Warning Boxes ..............................................................1-2 Not Included ..................................................................1-3 System Startup ...............................................................1-4 System Software ............................................................1-5 Model Differences .........................................................1-6 System Map: LCD Panel Open - Model A Design I .....1-7 System Map: LCD Panel Open - Model A Design II ....1-8
Features & Components

Overview ........................................................................2-1 Hard Disk Drive .............................................................2-2 Optical (CD/DVD) Device ............................................2-3 Loading Discs ................................................................2-3 Handling CDs or DVDs .................................................2-4
XVII
Preface
DVD Regional Codes ....................................................2-5 Multi-In-1 Card Reader .................................................2-6 Touchpad and Buttons/Mouse .......................................2-7 Gestures and Device Settings ........................................2-8 Audio Features .............................................................2-11 Setup for Audio Recording ..........................................2-12 Adding a Printer ...........................................................2-13 USB Printer ..................................................................2-13 Parallel Printer .............................................................2-13 Conserving Battery Power ...........................................3-12 Battery Life ..................................................................3-13 New Battery .................................................................3-13 Recharging the Battery with the AC/DC Adapter .......3-13 Proper handling of the Battery Pack ............................3-14 Battery FAQ .................................................................3-15
Drivers & Utilities

What to Install ................................................................4-1 Module Driver Installation .............................................4-1 Driver Installation ..........................................................4-2 Updating/Reinstalling Individual Drivers ......................4-4 User Account Control ....................................................4-5 Windows Security Message ...........................................4-5 New Hardware Found ....................................................4-5 Driver Installation Procedure .........................................4-6 Chipset ...........................................................................4-6 Video (VGA) .................................................................4-6 LAN ...............................................................................4-6 CardReader ....................................................................4-6 Touchpad .......................................................................4-6 Hot Key ..........................................................................4-7 USB 3.0 ..........................................................................4-7 MEI Driver .....................................................................4-7 Audio .............................................................................4-7
Power Management
Overview ........................................................................3-1 The Power Sources ........................................................3-2 AC/DC Adapter .............................................................3-2 Battery ............................................................................3-2 Turning On the Computer ..............................................3-3 Power Plans ...................................................................3-4 Power-Saving States ......................................................3-6 Sleep ..............................................................................3-6 Hibernate ........................................................................3-7 Shut down ......................................................................3-7 Configuring the Power Buttons .....................................3-8 Resuming Operation ......................................................3-9 Energy Star Power Saving ...........................................3-10 Battery Information .....................................................3-11
XVIII
Preface
Windows Experience Index ...........................................4-8 Optional Drivers ............................................................4-9 PC Camera Module ........................................................4-9 Wireless LAN Module ...................................................4-9 3.75G/HSPA Module .....................................................4-9 Intel Rapid Storage Technology Driver .........................4-9 Legacy USB Support: (Advanced Menu) ......................5-8 Boot Logo (Advanced Menu) ........................................5-9 Power On Boot Beep (Advanced Menu) .......................5-9 Battery Low Alarm Beep: (Advanced Menu) ................5-9 Security Menu ..............................................................5-10 Set Supervisor Password (Security Menu) ..................5-10 Boot Menu ...................................................................5-12 Boot Sequence (Boot Menu) ........................................5-13 Exit Menu ....................................................................5-14
BIOS Utilities
Overview ........................................................................5-1 The Setup Utility ............................................................5-2 Failing the POST ...........................................................5-3 Fatal Errors ....................................................................5-3 Non-Fatal Errors ............................................................5-3 Setup Screens .................................................................5-4 Main Menu .....................................................................5-5 System Time & Date (Main Menu) ...............................5-5 SATA Port # (Main Menu) ............................................5-6 System/Extended Memory: (Main Menu) .....................5-6 MB Series / BIOS Revision / KBC/EC firmware Revision ..........................................5-6 Advanced Menu .............................................................5-7 Advanced Chipset Control (Advanced Menu) ..............5-7 Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...........................................5-8 SATA Mode Selection (Advanced Menu) ....................5-8
Upgrading The Computer

Overview ........................................................................6-1 When Not to Upgrade ....................................................6-2 Removing the Battery ....................................................6-3 Upgrading the Hard Disk Drive .....................................6-4 Upgrading the Optical (CD/DVD) Device ....................6-7 Removing the Optical Device for Model A Computers .......................................................6-8 Removing the Optical Device for Model B & C Computers .............................................6-10 Upgrading the System Memory (RAM) ......................6-11
Modules & Options

Overview ........................................................................7-1 PC Camera Module ........................................................7-2 PC Camera Driver Installation .......................................7-3
XIX
Preface
Wireless LAN Module .................................................7-10 3rd Party WLAN Driver Installation ...........................7-11 Intel WLAN Driver Installation ...............................7-11 Connecting to a Wireless Network in Windows 7 .......7-12 Intel My WiFi Configuration ....................................7-15 Intel WLAN & Bluetooth Combo Module High-Speed Data Transfer Configuration ....................7-27 Windows Mobility Center ...........................................7-29 Bluetooth & WLAN Combo Module ..........................7-30 3rd Party Bluetooth Combo Driver Installation ...........7-31 3rd Party Bluetooth & WLAN Combo Settings ..........7-32 Bluetooth Networking Setup .......................................7-35 Bluetooth & WLAN Combo Module Configuration ...7-36 Intel Bluetooth Combo Driver Installation ..................7-39 Standard Bluetooth Configuration in Windows 7 .......7-40 3.75G/HSPA Module ...................................................7-44 Wireless Manager ........................................................7-48 Wireless Manager Installation .....................................7-48 Wireless Manager Application ....................................7-49 Profiles .........................................................................7-52 Settings ........................................................................7-56 Text Messaging Service (SMS) ...................................7-59 SMS Utility ..................................................................7-59 Sending a Text Message ..............................................7-61 Phonebook ...................................................................7-64 SMS Settings ...............................................................7-67 Intel Rapid Storage Technology ..................................7-70 IRST Driver Installation ..............................................7-70
Troubleshooting
Overview ........................................................................8-1 Basic Hints and Tips ......................................................8-2 Backup and General Maintenance .................................8-3 Viruses ...........................................................................8-4 Upgrading and Adding New Hardware/Software ..........8-5 Problems and Possible Solutions ...................................8-7 Bluetooth Connection Problems ..................................8-12 Intel Centrino Advanced WLAN & Bluetooth V3.0+HS Combo Modules ..........................8-16
Interface (Ports & Jacks)

Overview .......................................................................A-1 Notebook Ports and Jacks .............................................A-2
Video Driver Controls

Video Driver Installation .............................................. B-1 Dynamic Video Memory Technology ......................B-1 Intel Graphics & Media Control Panel ...................... B-2 Display Devices & Options ......................................B-4 Attaching Other Displays .............................................. B-5 Configuring an External Display in Windows 7 ........... B-8
XX
Preface
HDMI Audio Configuration ....................................... B-11 Dimensions & Weight .................................................. C-5
Specifications
Processor ....................................................................... C-2 Processor ....................................................................... C-2 Core Logic .................................................................... C-2 Display .......................................................................... C-2 Memory ......................................................................... C-2 Video ............................................................................. C-3 BIOS ............................................................................. C-3 Storage .......................................................................... C-3 Audio ............................................................................ C-3 Keyboard, Pointing Device & Buttons ......................... C-3 Interface ........................................................................ C-3 Card Reader .................................................................. C-3 Slot ................................................................................ C-3 Communication ............................................................. C-4 Communication ............................................................. C-4 Power Management ...................................................... C-4 Power ............................................................................ C-4 Security ......................................................................... C-4 Indicators ...................................................................... C-4 Design Feature .............................................................. C-5 Operating System .......................................................... C-5 Environmental Spec ...................................................... C-5
XXI
Preface
XXII
Quick Start Guide
Chapter 1: Quick Start Guide

Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, card reader), Touchpad & Mouse, Audio & Printer. Chapter 3 The computers power saving options. Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computers subsystems. Chapter 5 An outline of the computers built-in software or BIOS (Basic Input Output System). Chapter 6 Instructions for upgrading your computer. Chapter 7 A quick guide to the computers PC Camera, Wireless LAN, Combo Bluetooth & WLAN and 3.75G/HSPA modules (some of which may be optional depending on your purchase configuration). Chapter 8 A troubleshooting guide. Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices. Appendix B Information on the video driver controls. Appendix C The computers specification.
Overview 1 - 1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to What to Install on page 4 - 1, BIOS Utilities on page 5 - 1 and Upgrading The Computer on page 6 - 1 in the reminder of the Users Manual. You may also find the notes marked with a of interest to you.
Beginners and Not-So-Advanced Users
Notes
Check the light colored boxes with the mark above to find detailed information about the computers features.
If you are new to computers (or do not have an advanced knowledge of them) then the information contained in the Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the Users Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a as indicated in the margin. For a more detailed description of any of the interface ports and jacks see Interface (Ports & Jacks) on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Not Included
Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in Drivers & Utilities on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasnt been properly configured (your service representative may have already done that for you); refer to Chapter 4 for installation instructions.
Ports and Jacks

See Notebook Ports and Jacks on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Overview 1 - 3
Quick Start Guide
System Startup
1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Use one hand to raise the lid/LCD to a comfortable viewing angle (do not exceed 130 degrees); use the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the computer by the lid/LCD).
Shutdown
Note that you should always shut your computer down by choosing the Shut Down command from the bottom right of the Start menu in Windows. This will help prevent hard disk or system problems.
130
Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In
1 - 4 System Startup
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7 operating system.
Windows OS
In order to run Windows 7 without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM), however if you are running Windows 7 64 bit your computer requires a minimum 2GB of system memory (RAM).
System Startup 1 - 5
Quick Start Guide
Model Differences
This notebook series includes three different models that vary slightly in design style (Models A and B include two distinct design styles), color, general appearance and features supported. Note that your computer may look slightly different from that pictured throughout this manual.
Feature
Display Type Supported
Model A 14.0 / 35.56cm HD (1366 * 768), 16:9 Panel
Model B 15.6 / 39.62cm HD (1366 * 768) / HD+ (1600 * 900), 16:9 Panel 374mm (w) * 250mm (d) * 14.3 - 34.1mm (h) 2.3 kg with 48.84WH Battery & ODD For Some Model B Designs: 374mm (w) * 250mm (d) * 14.3 - 35.3mm (h) 2.3 kg with 48.84WH Battery & ODD 374mm (w) * 250mm (d) * 20 - 37.2mm (h) 2.6 kg with 48.84WH Battery & ODD
Model C 17.3 / 43.94cm 16:9 HD+ (1600 * 900) TFT LCD
340mm (w) * 238mm (d) * 13.9 - 31.8mm (h) 2.2 kg with 48.84WH Battery & ODD
Dimensions & Weight
For Some Model A Designs: 341mm (w) * 238.5mm (d) * 16-34mm (h) 2.2 kg with 48.84WH Battery & ODD
413mm(w) * 270mm(d) * 14 - 40.5mm(h) 2.9kg with ODD & 48.84WH Battery
See Specifications on page C - 1 for full details of differences between the models.
Table 1 - 1 - Model Differences
1 - 6 System Startup
Quick Start Guide
System Map: LCD Panel Open - Model A Design I

1
Wireless Device Operation Aboard Aircraft 1. 2. 3. 4. 5.
Figure 1 - 2 LCD Panel Open Model A Design I Built-In PC Camera (Optional) LCD Power Button Hot Key Buttons LED Status Indicators (see Table 1 - 3, on page 1 - 11) Keyboard Built-In Microphone Touchpad & Buttons
The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
5 6
7 8
Use the key combinations to toggle power to the 3.75G/ HSPA/WLAN/Bluetooth modules, and check the LED indicator or on-screen icon to see if the modules are powered on or not (see Table 1 5, on page 1 - 16/ Table 1 2, on page 1 - 11).
6. 7. 8.
8
Touchpad Buttons (valid operation area)
Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines indicated on the right.
System Map: LCD Panel Open - Model A Design I 1 - 7
Quick Start Guide

Figure 1 - 3 LCD Panel Open Model A Design II 1. 2. 3. 4. 5. 6. 7. Built-in PC Camera (Optional) LCD Power Button LED Status Indicators Keyboard Built-In Microphone Touchpad & Buttons
System Map: LCD Panel Open - Model A Design II

1
Wireless Device Operation Aboard Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the key combinations to toggle power to the 3.75G/HSPA/ WLAN/Bluetooth modules, and check the LED indicator or onscreen icon to see if the modules are powered on or not (see Table 1 - 5, on page 1 - 16/ Table 1 - 2, on page 1 - 11).
4 5 7 6
Touchpad Buttons (valid operation area)
7
1 - 8 System Map: LCD Panel Open - Model A Design II
Quick Start Guide
System Map: LCD Panel Open - Model B

1

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the key combinations to toggle power to the 3.75G/HSPA/ WLAN/Bluetooth modules, and check the LED indicator or onscreen icon to see if the modules are powered on or not (see Table 1 - 5, on page 1 - 16/ Table 1 - 2, on page 1 - 11).
Figure 1 - 4 LCD Panel Open Model B 1. 2. 3. 4. 5. 6. 7. Built-in PC Camera (Optional) LCD Power Button LED Status Indicators Keyboard Built-In Microphone Touchpad & Buttons
4 5
6 4 7
System Map: LCD Panel Open - Model B 1 - 9
Quick Start Guide

Figure 1 - 5 LCD Panel Open Model C 1. 2. 3. 4. 5. 6. 7. Built-In PC Camera (Optional) LCD Power Button LED Indicators Keyboard Built-In Microphone Touchpad & Buttons
System Map: Model C - LCD Panel Open

1

4 5 7 6
Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above.
Use the key combinations to toggle power to the WLAN/ Bluetooth modules, and check the LED indicator or on-screen icon to see if the modules are powered on or not (see Table 1 - 5, on page 1 - 16/ Table 1 - 3, on page 1 - 11).
1 - 10 System Map: Model C - LCD Panel Open
Quick Start Guide
LED Indicators
The LED indicators on the computer display helpful information about the current status of the computer.
Icon Color
Orange Green Blinking Green Orange Green Blinking Orange
Icon
Color
Green Orange Green Green Green Blue
Description
The (optional) Wireless LAN Module is Powered On The (optional) Bluetooth Module is Powered On Hard Disk Activity Number Lock Activated Caps Lock Activated Power Button
Description
DC Power is Plugged In The Computer is On The Computer is in Sleep Mode The Battery is Charging The Battery is Fully Charged The Battery Has Reached Critically Low Power Status
Table 1 - 3 - LED Status Indicators
Table 1 - 2 - LED Power Indicators
Note that Model A Design II computers have only hard disk activity and WLAN/Bluetooth icons.
LED Indicators 1 - 11
Quick Start Guide
Hot Key Buttons - Model A Design I Only

These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button press.
Hot Key Function
3 1 2 3
Toggle *Silent Mode (for power saving)
Activate the Default Internet Program Activate the Default E-Mail Browser (Note that in Windows 7 without Outlook/Outlook Express installed this button has no function. If Outlook/Outlook Express are installed then the button will activate the application)
Table 1 - 4 - Hot Key Buttons - Model A Design I Only
*When enabled, Silent Mode will reduce fan noise and save power consumption. Note this may reduce computer performance.
1 - 12 Hot Key Buttons - Model A Design I Only
Quick Start Guide
Keyboard - Model A
The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 5, on page 1 - 16 for full function key combination details.
Function Keys
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the systems regular keyboard may not work.
Play/Pause Key Numerical Keypad
NumLk & ScrLk Keys 3.75G/HSPA Module Power Toggle Key
Fn Key
NumLk & ScrLk

Hold down the Fn Key and either NumLk or ScrLk to enable number or scroll lock, and check the LED indicator for status.
Figure 1 - 6 - Keyboard - Model A
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.
Keyboard - Model A 1 - 13
Quick Start Guide
Other Keyboards
Keyboard - Model B
Function Keys NumLk & ScrLk Keys Play/Pause Key 3.75G/HSPA Module Power Toggle Key Numerical Keypad
NumLk & ScrLk

Fn Key
Figure 1 - 7 - Keyboard - Model B
Special Characters
1 - 14 Keyboard - Model B
Quick Start Guide
Keyboard - Model C
Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad
Other Keyboards
NumLk & ScrLk

Fn Key
Figure 1 - 8 - Keyboard - Model C
Special Characters
Keyboard - Model C 1 - 15
Quick Start Guide
Function/Hot Key Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.
Keys
Fn + ~
Function
Play/Pause (in Audio/Video Programs)
Keys
Fn + F8/F9
Function
Brightness Decrease/Increase *Silent Mode Toggle (for some Model A Designs only - see page 3 - 2)
Fn +
3.75G Module Power Toggle*
Fn + F1
TouchPad Toggle
Fn + F10
PC Camera Power Toggle
Fn + F2
Turn LCD Backlight Off (Press a key to or use TouchPad to turn on)
Fn + F11
WLAN Module Power Toggle
Fn + F3
Mute Toggle
Fn + F12
Bluetooth Module Power Toggle
Fn + F4
Sleep Toggle
Fn + NumLk
Number Lock Toggle
Fn + F5/ F6
Volume Decrease/ Increase
Fn + ScrLk
Scroll Lock Toggle
Fn + F7
Display Toggle
Caps Lock
Caps Lock Toggle
Table 1 - 5 - Function & Hot Key Indicators
1 - 16 Function/Hot Key Indicators
Quick Start Guide
System Map: Front & Left Views - Models A & B

Model A
1
Model B
Figure 1 - 9 Front & Left Views Models A & B 1. LED Power Indicators (see Table 1 - 2, on page 1 - 11) DC-In Jack External Monitor Port RJ-45 LAN Jack HDMI-Out Port USB 2.0 Port Vent/Fan Intake/ Outlet USB 2.0 Port Multi-in-1 Card Reader
1
Model A
6
Model B
8 7
2. 3.
4. 5. 6. 7. 8. 9.
Multi-In-1 Card Reader

The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible MS (Memory Stick) / MS Pro / MS Duo
System Map: Front & Left Views - Models A & B 1 - 17
Quick Start Guide

Figure 1 - 10 Front & Left Views Model C 1. LED Indicators (see Table 1 - 2, on page 1 - 11) DC-In Jack External Monitor Port RJ-45 LAN Jack HDMI-Out Port USB 3.0 Port Vent/Fan Intake USB 2.0 Port Multi-In-1 Card Reader
System Map: Front & Left Views - Model C

1
2. 3. 4. 5. 6. 7. 8. 9.
5 4

The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible MS (Memory Stick) / MS Pro / MS Duo USB 3.0 Port OR USB 2.0 Port This model includes a single USB 3.0 port on the left side of the computer. The USB 3.0 port is denoted by its blue color; USB 2.0 ports are colored black. Note that the USB 3.0 port requires a driver installation and does not support wake on USB.
1 - 18 System Map: Front & Left Views - Model C
Quick Start Guide
System Map: Right & Rear Views - Models A & B

Model A
Figure 1 - 11 Right & Rear Views Models A & B 1. Microphone-In Jack 2. Headphone-Out Jack 3. USB 2.0 Port 4. Optical Device Drive Bay (for CD/ DVD Device) 5. Security Lock Slot 6. Battery
Model B
Model A
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See Battery Information on page 3 - 11 for full instructions.
Model B
System Map: Right & Rear Views - Models A & B 1 - 19
Quick Start Guide

Figure 1 - 12 Right & Rear Views Model C 1. 2. 3. 4. 5. 6. Headphone-Out Jack Microphone-In Jack USB 2.0 Port Optical Device Drive Bay Security Lock Slot Battery
System Map: Right & Rear Views - Model C
1 2
1 - 20 System Map: Right & Rear Views - Model C
Quick Start Guide
Disk Eject Warning

Dont try to eject a CD/DVD while the system is accessing it. This may cause the system to crash. Stop the disk first then eject it, or press the stop button twice.
Changing DVD Regional Codes

Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see DVD Regional Codes on page 2 - 5). DVD region detection is device dependent, not OSdependent. You can select your modules region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.
CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole. Dont try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to crash.
System Map: Right & Rear Views - Model C 1 - 21
Quick Start Guide

Figure 1 - 13 Bottom View Model A 1. 2. 3. 4. 5. Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3.75G USIM Card Cover (Optional)
System Map: Bottom View - Model A

1 3 3 2 3
CPU
The CPU is not a user serviceable part.
Overheating
To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Bottom Covers
If your model includes the 3.75G option then a small cover 5 to enable you to access the modules USIM card will be included (see 3.75G/HSPA Module on page 7 - 44).
1 - 22 System Map: Bottom View - Model A
Quick Start Guide
System Map: Bottom View - Model B

1 3 3 2 3 5
Figure 1 - 14 Bottom View - Model B 1. 2. 3. 4. 5. 6. Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3.75G USIM Card Cover (Optional) Speakers
CPU
Bottom Covers
If your model includes the 3.75G option then a small cover 5 to enable you to access the modules USIM card will be included (see 3.75G/HSPA Module on page 7 - 44).
Overheating
System Map: Bottom View - Model B 1 - 23
Quick Start Guide

Figure 1 - 15 Bottom View Model C 1. 2. 3. 4. 5. Battery Component Bay Cover Fan Intake/Vent Hard Disk Bay Cover Speakers
System Map: Bottom View - Model C

1 3 3 2 3
Battery Information
5
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
CPU
Overheating
1 - 24 System Map: Bottom View - Model C
Quick Start Guide
Windows 7 Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Click here to toggle Category View
Figure 1 - 16 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all controls it may be necessary to toggle off Category View to view the control panel icons.
System Map: Bottom View - Model C 1 - 25
Quick Start Guide
Video Features
You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 7 (see over). For more detailed video information see Video Driver Controls on page B - 1. To access Display (Control Panel) and Screen Resolution in Windows:
1. 2. 3. 4. 5. 6. Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category. Click Adjust Screen Resolution/Adjust resolution. Alternatively you can right-click the desktop and select Screen resolution. Use the dropbox to select the screen Resolution 1 (Figure 1 - 17). Click Advanced settings 2 (Figure 1 - 17) to bring up the Advanced properties tabs.
1 2
Figure 1 - 17 - Screen Resolution
1 - 26 Video Features
Quick Start Guide

To access the Intel(R) Graphics and Media Control Panel:
1. 2. Click Advanced settings 2 (Figure 1 - 17 on page 1 - 26) in the Display Settings control panel in Windows. Click Graphics Properties (button) 3 (Figure 1 - 18) in the Intel Graphics & Media Control Panel tab. Right-click the desktop and select Graphics Properties from the menu. Click the icon
4 (Figure 1 - 18) in the taskbar and select Graphics Properties from the menu.
OR
3.
OR
4.
OR
5. Access the Intel(R) Graphics and Media Control Panel from the Windows control panel in Classic View.
Figure 1 - 18 - Intel Graphics and Media Control Panel
Video Features 1 - 27
Quick Start Guide
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 24) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance. Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change plan settings and click Change advanced power settings to access further configuration options. Pay attention to the instructions on battery care in Battery Information on page 3 - 11.
Figure 1 - 19 - Power Options
1 - 28 Power Options
Chapter 2: Features & Components

Overview
Read this chapter to learn more about the following main features and components of the computer: Hard Disk Drive Optical (CD/DVD) Device Multi-In-1 Card Reader Touchpad and Buttons/Mouse Audio Features Adding a Printer
Overview 2 - 1
Power Safety
Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.
Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm. The hard disk is accessible from the bottom of your computer as seen below. For further details see Upgrading the Hard Disk Drive on page 6 - 4.
Model A
Model C
Figure 2 - 1
Hard Disk Location
Model B
2 - 2 Hard Disk Drive
Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see Storage on page C - 3). The optical device is usually labeled Drive D: and may be used as a boot device if properly set in the BIOS (see Boot Menu on page 5 - 12).
Sound Volume Adjustment

How high the sound volume can be set depends on the setting of the volume control within Windows. Click the Volume icon on the taskbar to check the setting (see Audio Features on page 2 - 11).
Loading Discs
To insert a CD/DVD, press the open button 1 and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the trays spindle). Gently push the CD/DVD tray in until its lock clicks and you are ready to start. The busy indicator 2 will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole 3 to open the tray.
Figure 2 - 2
Optical Device
Optical (CD/DVD) Device 2 - 3
Handling CDs or DVDs
CD Emergency Eject
If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.
Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed. Note the following: Hold the CD or DVD by the edges; do not touch the surface of the disc. Use a clean, soft, dry cloth to remove dust or fingerprints. Do not write on the surface with a pen. Do not attach paper or other materials to the surface of the disc. Do not store or place the CD or DVD in high-temperature areas. Do not use benzene, thinner, or other cleaners to clean the CD or DVD. Do not bend the CD or DVD. Do not drop or subject the CD or DVD to shock.
Disk Eject Warning

Dont try to remove a CD/DVD while the system is accessing it. This may cause the system to crash.
2 - 4 Optical (CD/DVD) Device
DVD Regional Codes

To change the DVD regional codes:
1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
DVD Region Note

DVD region detection is device dependent, not OS-dependent. You can select your modules region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.
Region 1 - USA & Canada Region 2 - Western Europe, Japan, South Africa, Middle East & Egypt Region 3 - South-East Asia, Taiwan, South Korea, The Philippines, Indonesia, Hong Kong Region 4 - South & Central America, Mexico, Australia, New Zealand Region 5 - N Korea, Russia, Eastern Europe, India & Most of Africa Region 6 - China
Figure 2 - 3
DVD Region Codes
Optical (CD/DVD) Device 2 - 5
Card Reader Cover

Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see CardReader on page 4 - 6. MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo Note: Some of these cards require PC adapters that are usually supplied with the cards.
Model A
Figure 2 - 4
Left View 1. Card Reader
1
Model B
1
Model C
2 - 6 Multi-In-1 Card Reader
Touchpad and Buttons/Mouse

The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse. Once you have installed the Touchpad driver (see TouchPad on page 4 - 6) you can configure the functions by double-clicking the Touchpad driver icon in the notification area. You may then configure the Touchpad tapping, buttons, scrolling (see sidebar), pointer motion and sensitivity options to your preferences.
Touchpad Scrolling
This computer model series may feature different Touchpad versions. These Touchpads may differ in their vertical scrolling function in most scrollable windows. Some Touchpads require sliding the finger up and down on the right of the Touchpad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the Touchpad to scroll the window.
Figure 2 - 5
Mouse Properties
Touchpad and Buttons/Mouse 2 - 7
Show Video
You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item. Select the gesture (Pinch Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu and click the Show Video button to see the demonstration video. For more details on any of the gestures see the help in the lower part of the right menu window.
Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties:
1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mouse (Hardware and Sound). Click Device Settings (tab) and click Settings. Use the menu tree on the left to access the user configurable settings.
Figure 2 - 6
Mouse Properties Device Settings
2 - 8 Touchpad and Buttons/Mouse

Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight continuous motion).
2
Figure 2 - 7
Scrolling Gesture
Mouse Driver
If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the devices user documentation for details.
Zooming The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality. Place two fingers on the Touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.
Figure 2 - 8
Zooming Gesture
Touchpad and Buttons/Mouse 2 - 9
Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left target zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Figure 2 - 9
Rotating Gesture
Three Finger-Flick/Three Fingers Down (Press) The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The Three Fingers Down gesture may be used to launch user-selectable applications.
Figure 2 - 10
Flick/Press Gesture
2 - 10 Touchpad and Buttons/Mouse
Audio Features
You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the notification area icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination (see Table 1 - 6, on page 1 - 17).
Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the notification area to check the setting.
Figure 2 - 11
Right-click the icon to access the menu above.
Realtek Audio Manager
See HDMI Audio Configuration on page B - 17 for a description of the audio configuration when connecting an HDMI supported display device.
Audio Features 2 - 11
Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instructions below:
1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the notification area icon and select Sound Manager). Click Microphone Effects (tab) in Microphone (tab), and then click to select Noise Suppression (button), or adjust the Recording Volume level to around 60, to obtain the optimum recording quality. Click OK to close the control panel and save the settings.
4.
Figure 2 - 12
Realtek Audio Manager Recording Setup
2 - 12 Audio Features
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options.
Parallel Printer
After setting up the printer attach the parallel cable to the printer. Connect the printers parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.
USB Printer
Most current printers have a USB interface connection. You may use any one of the ports to connect the printer.
Install Instructions:
1. 2. 3. 4. 5. Set up the printer according to its instructions (unpacking, paper tray, toner/ink cartridge etc.). Turn ON the computer. Turn ON the printer. Connect the printers USB cable to one of the USB ports on the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar, however you will need to purchase a parallel to USB converter.
Adding a Printer 2 - 13
2 - 14
Power Management
Chapter 3: Power Management

Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the LCD and hard disk drive) or the whole system. This chapter covers: The Power Sources Turning On the Computer Power Plans Power-Saving States Configuring the Power Buttons Energy Star Power Saving Battery Information
OS Note
Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the users manual of your operating system. (Note: All pictures used on the following pages are from the Windows 7 OS.)
The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.
Overview 3 - 1
Power Management
3
Silent Mode (Model A Design I Only)
Use the key to toggle Silent Mode to reduce fan noise and save power consumption. Note this may reduce computer performance.
The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.
1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle. Press the power button to turn On.
Battery
The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see How do I completely discharge the battery? on page 3 - 15). We recommend that you do not remove the battery. For more information on the battery, please refer to Battery Information on page 3 - 11.
3 - 2 The Power Sources
Power Management
Turning On the Computer

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Forced Off
If the system hangs, and the Ctrl + Alt + Del key combination doesnt work, press the power button for 4 seconds, or longer, to force the system to turn itself off.
Shut Down
Note that you should always shut your computer down by choosing the Shut Down command from the bottom right of the Start menu in Windows. This will help prevent hard disk or system problems.
Power Button as Stand by or Hibernate Button

You can use the OSs Power Options control panel to set the power button to send the system into Stand by or Hibernate mode (see your OSs documentation, or Configuring the Power Buttons on page 3 - 8 for details).
Turning On the Computer 3 - 3
Power Management
3
Resuming Operation
See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state.
Power Plans
The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Password
It is recommended that you enable a password on system resume in order to protect your data.
Figure 3 - 1
Power Plan Advanced Settings (Win 7)
3 - 4 Power Plans
Power Management
Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered. The recommended Balanced power plan will balance power saving and performance.
Figure 3 - 2
Click to Show/Hide additional power plans
Power Plans
Power Plans 3 - 5
Power Management
Power-Saving States
3
You can use power-saving states to stop the computers operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power. The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used. If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.
3 - 6 Power-Saving States
Power Management
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery.
Silent Mode (Model A Design I Only)

You can use Silent Mode to reduce power consumption and fan noise. Use the Silent Mode hot key to toggle this mode on/off. On screen visual indicators will display the Silent Mode status (see Table 1 - 5, on page 1 14). Note Silent Mode may reduce computer performance.
Shut down
You should Shut down the computer if you plan to install new hardware (dont forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.
Figure 3 - 3
Lock Button menu
Power-Saving States 3 - 7
Power Management
3
Password Protection
It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable).
Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
Figure 3 - 4
Power Options Define Power Buttons
3 - 8 Configuring the Power Buttons
Power Management
Resuming Operation
You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Status
Power Off Sleep
Closing the Lid

If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Icon
Off
Color
To Resume
Press the Power Button Press the Power Button
Blinking Green Press the Sleep Button (Fn + F4 Key Combo) Off (battery)
Table 3 - 1
Press the Power Button
Hibernate Orange (AC/DC adapter) Display Turned Off Green
Resuming Operation
Press a Key or Move the Mouse/Touchpad
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).
Configuring the Power Buttons 3 - 9
Power Management
3
Taskbar Icon
If the taskbar icon does not appear then click the taskbar arrow and select Customize.
Energy Star Power Saving

This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. If you want to enable Energy Star power saving then follow these instructions:
1. 2. 3. Right-click the taskbar icon (see sidebar). Select Power Conservation Modes. Select Energy Star to use the Energy Star power management and override other power saving settings.
Select Show icon and notifications alongside the Hot key icon and click OK. The icon will now appear in the taskbar.
Conservation Modes
The default Energy Star setting will result in maximum power saving, but with the possible loss of some performance. Setting the mode to Balance will give power saving matched with performance. Performance will give optimum computer performance but with less power conservation.
Figure 3 - 5
Energy Star Menu
3 - 10 Energy Star Power Saving
Power Management
Battery Information
Follow these simple guidelines to get the best use out of your battery.
Low Battery Warning

When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted.
Battery Power
Your computers battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 1 on page 3 - 4). Click the battery icon status. in the taskbar to see the current battery level and charge
Figure 3 - 6
Battery Icon (Taskbar) & Battery Advanced Settings
Battery Information 3 - 11
Power Management
3
Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc.
Conserving Battery Power

Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. Reduce the amount of time before the display is turned off. Close wireless, Bluetooth, modem or communication applications when they are not being used. Disconnect/remove any unnecessary external devices e.g. USB devices, ExpressCards etc.
Figure 3 - 7
Windows Mobility Center
3 - 12 Battery Information
Power Management
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see Removing the Battery on page 6 - 3.
New Battery
Always completely discharge, then fully charge, a new battery (see Battery FAQ on page 3 - 15 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to LED Indicators on page 1 - 11 for information on the battery charge status, and to Battery Information on page 3 - 11 for more information on how to maintain and properly recharge the battery pack.)
Power Management
Proper handling of the Battery Pack
3
Caution
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturers instructions.
DO NOT disassemble the battery pack under any circumstances DO NOT expose the battery to fire or high temperatures, it may explode DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center. If the battery has been dropped we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years.
Power Management
Battery FAQ
How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Dont turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1. 2. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Figure 3 - 8
Power Plan Create
Power Management
3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Figure 3 - 9
Change Plan Settings / Change Advanced Power Settings
Power Management
4. 5. Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears):
Figure 3 - 10
Power Options Advanced Settings Battery
Low battery levels = 0% Critical battery Levels = 1% Low battery action = Do Nothing Critical battery action (On battery) = Shut Down Critical battery action (Plugged in) = Do Nothing
Power Management
How do I fully charge the battery? When charging the battery, dont stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities
Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computers subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems havent built in drivers and utilities. Thus, some of the system components wont be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.
Driver Installation & Power

When installing drivers make sure your computer is powered by the AC/DC adapter connected to a working power source. Some drivers draw a significant amount of power during the installation procedure, and if the remaining battery capacity is not adequate this may cause the system to shut down and cause system problems (note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).
What to Install
The Device Drivers & Utilities + Users Manual disc contains the drivers and utilities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 3 lists what you need to install and it is very important that the drivers are installed in the order indicated.
Module Driver Installation

The procedures for installing drivers for the PC Camera, Wireless LAN, Bluetooth & WLAN Combo and 3.75G modules are provided in Modules & Options on page 7 - 1.
What to Install 4 - 1
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + Users Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu.
1.
2. 3.
Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them). Follow the instructions for each individual driver installation procedure as listed on the following pages.
Figure 4 - 1 - Drivers Installer Screen 1 Figure 4 - 2 - Drivers Installer Screen 2 4 - 2 Driver Installation
Drivers & Utilities

Win 7 SP1 Driver Chipset Video (VGA) LAN CardReader Touchpad Hot Key USB 3.0 (for Model C only) MEI Driver Audio Page # Page 4 - 6 Page 4 - 6 Page 4 - 6 Page 4 - 6 Page 4 - 6 Page 4 - 7 Page 4 - 7 Page 4 - 7 Page 4 - 7 Win 7SP1 Driver PC Camera Module Wireless LAN Module Bluetooth & WLAN Combo Module 3.75G/HSPA Module (for Models A & B only) Intel Rapid Storage Technology (required for hard disks in AHCI mode) Page # Page 7 - 2 Page 7 - 10 Page 7 - 30 Page 7 - 44 Page 7 - 70
Table 4 - 1 - Driver Installation

All drivers provided are for Windows 7 with Service Pack 1. Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth Combo modules.
Driver Installation 4 - 3
Drivers & Utilities

Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder.
Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter. If the driver is not listed in the Programs and Features menu:
1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Device Manager (Hardware and Sound > Device Manager). Double-click the device you wish to update/reinstall the driver for (you may need to click + to expand the selection). Click Driver (tab) and click the Update Driver or Uninstall button and follow the on screen prompts.
Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See Windows Update on page 4 8 for instructions.
4.
4 - 4 Driver Installation
Drivers & Utilities
User Account Control

If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed.
New Hardware Found

If you see the message New Hardware Found during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Windows Security Message

If you receive a Windows security message as part of the driver installation process. Just click Install this driver software anyway or Install to continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
Driver Installation General Guidelines The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press. Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a restart is required to install the driver. Make sure any modules (e.g. PC Camera, WLAN or 3.75G/HSPA) are ON before installing the appropriate driver.
Drivers & Utilities
Driver Installation Procedure

Insert the Device Drivers & Utilities + Users Manual disc and click Install Drivers (button).
Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer.
Note: After installing the video driver go to the Display/Display Settings control panel to adjust the video settings to the highest resolution.
LAN 1. Click 3.Install LAN Driver > Yes. 2. Click Install. 3. Click Finish. CardReader 1. Click 4.Install Cardreader Driver > Yes. 2. Click Install. 3. Click Finish. Touchpad 1. Click 5.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license agreement and click Next. 4. Click Finish > Restart Now to restart the computer.
Drivers & Utilities
Hot Key 1. Click 6.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. USB 3.0
(for Model C only) 1. Click 7.Install USB 3.0 Driver > Yes. 2. Click Next. 3. Click the button to accept the license agreement and click Next. 4. Click Install. 5. Click Finish. OR 1. Click 7.Install USB 3.0 Driver > Yes. 2. Choose the language you prefer and click OK. 3. Click Next. 4. Click the button to accept the license agreement and click Next. 5. Click Finish.
MEI Driver 1. Click 8.Install MEI Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish. Audio 1. Click 9.Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer.
Note that after installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + Users Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click Option Drivers (button) to access the optional driver menu. It is recommended you now also install the Intel Rapid Storage Technology driver (see IRST Driver Installation on page 7 - 70 - required for AHCI mode hard disks). (see over)
Drivers & Utilities
Windows Experience Index
Windows Update
After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5. 6. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Windows Update (System and Security/ Security). Click Check for updates (button). The computer will now check for updates (you need to be connected to the internet). Click Install now (button) to begin checking for the updates. Click Install updates (button) to install the updates.
After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index (make sure the AC/DC adapter is plugged in):
1. Click Start, and click Control Panel. 2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index). 3. Click Rate this computer/Refresh Now/Rerun the assessment. 4. The computer will take a few minutes to assess the system performance. 5. Close the control panel.
Drivers & Utilities
Optional Drivers
See the pages indicated for the driver installation procedures for any modules included in your purchase option. Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth Combo modules.
3.75G/HSPA Module
(For Models A & B only) See 3.75G/HSPA Module on page 7 - 44.
Intel Rapid Storage Technology Driver

See IRST Driver Installation on page 7 - 70.
PC Camera Module
See PC Camera Module on page 7 - 2.
Wireless LAN Module

See Wireless LAN Module on page 7 - 10.
Bluetooth & WLAN Combo Module

See Bluetooth & WLAN Combo Module on page 7 - 30.
Optional Drivers 4 - 9
Drivers & Utilities
4 - 10
BIOS Utilities
Chapter 5: BIOS Utilities

Overview
This chapter gives a brief introduction to the computers built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing. There is one general rule: Dont make any changes unless you are sure of what you are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Screens
Note that the BIOS screens pictured on these pages are intended for guidance in setting up your systems BIOS. BIOS versions are subject to constant change and revision, therefore your computers actual screens may appear slightly different from those pictured on these pages.
Overview 5 - 1
BIOS Utilities
BIOS Settings Warning

Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with <F2>, or Optimized Defaults with <F3>.
The Setup Utility

Each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup. If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you cant get into Setup without rebooting. The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). To enter Setup, turn on the computer and press F2 (give the system a few seconds to enter Setup). If the Boot Logo is enabled the F2 on screen will be highlighted to illustrate that the system is processing the request during the POST (or press F7 for boot options). If you get a Keyboard Error, (usually because you pressed F2 too quickly) just press F2 again. If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear. To see the boot options press F7 and choose your preferred boot device.
5 - 2 The Setup Utility
BIOS Utilities
Failing the POST

Errors can be detected during the POST. There are two categories, fatal and nonfatal.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) and you can then press F7 (the F7 on screen will be highlighted to illustrate that the system is processing the request) for boot options. Press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the cure seems even worse, call for help.
The Setup Utility 5 - 3
BIOS Utilities
Setup Menus
The Setup menus shown in this section are for reference only. Your computers menus will indicate the configuration appropriate for your model and options.
Setup Screens
The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box at the bottom right side of the screen.
Figure 5 - 1
Navigation Menu
If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page. The Item Specific Help on the upper right side of each screen explains the highlighted item and has useful messages about its options. If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.
5 - 4 The Setup Utility
BIOS Utilities
Main Menu
Figure 5 - 2
Main Menu
System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes. Main Menu 5 - 5
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computers SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
5
MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
5 - 6 Main Menu
BIOS Utilities
Advanced Menu
Figure 5 - 3
Advanced Menu
Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting.
Advanced Menu 5 - 7
BIOS Utilities
SATA Mode Selection

If you have installed the Windows 7 operating system with either IDE or AHCI mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows 7 OS).
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down. SATA Mode Selection (Advanced Menu) You can configure SATA (Serial ATA) control to operate in IDE (native/compatible), AHCI (Advanced Host Controller Interface) modes from this menu. The SATA Mode should be set BEFORE installing an operating system, and after you have backed up all necessary files and data (see sidebar). Legacy USB Support: (Advanced Menu) Choose Enabled if you intend to use USB devices in systems which do not normally support USB functionality (e.g. DOS). The default setting is Enabled and does not need to be changed if you intend to use your USB devices in Windows.
5 - 8 Advanced Menu
BIOS Utilities Boot Logo (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot Option functions. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. Battery Low Alarm Beep: (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
Advanced Menu 5 - 9
BIOS Utilities
Security Menu
The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
Security Menu
Figure 5 - 4
Security Menu
Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility). 5 - 10 Security Menu
BIOS Utilities
Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
Password Warning
If you set a boot password (Password on boot is Enabled), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Security Menu 5 - 11
BIOS Utilities
Boot Menu
Figure 5 - 5
Boot Menu
BIOS Screens
Note that the BIOS screens pictured on these pages are intended for guidance in setting up your systems BIOS. BIOS versions are subject to constant change and revision, therefore your computers actual screens may appear slightly different from those pictured on these pages.
When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Sequence. Item specific help on the right is available to help you move devices up and down the order.
5 - 12 Boot Menu
BIOS Utilities Boot Sequence (Boot Menu) Use the arrow keys to move up and down the menu and use the F5 and F6 keys to move the devices boot priority up and down the list (the selected device will be highlighted in white).
Boot Menu 5 - 13
BIOS Utilities
Exit Menu
Figure 5 - 6
Exit Menu
Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
5 - 14 Exit Menu
Chapter 6: Upgrading The Computer

Overview
This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need: A small crosshead or Phillips screwdriver A small regular slotted (flathead) screwdriver An antistatic wrist strap Before working with the internal components you will need to wear an antistatic wrist strap to ground yourself because static electricity may damage the components. The chapter includes: Removing the Battery Upgrading the Hard Disk Drive Upgrading the Optical (CD/DVD) Device Upgrading the System Memory (RAM)
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Please make sure that you review each procedure before you perform it.
Overview 6 - 1
When Not to Upgrade
Power Safety Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.
These procedures involve opening the systems case, adding and sometimes replacing parts. You should not perform any of these upgrades if: Your system is still under warranty or a service contract You dont have all the necessary equipment Youre not in the correct environment You doubt your abilities
Under any of these conditions, contact your service representative to purchase or replace the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.
Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
6 - 2 Overview
Removing the Battery

If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery.
1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
6
Figure 6 - 1
Battery Removal
Model A
Model B
Model C
Removing the Battery 6 - 3
HDD System Warning

New HDDs are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the discs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading the Hard Disk Drive

The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h) (see Storage on page C - 3). Follow your operating systems installation instructions, and install all necessary drivers and utilities (see Driver Installation on page 4 - 2), when setting up a new hard disk.
6 - 4 Upgrading the Hard Disk Drive

1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 .
Model A
1 2
Model B
1 2
6
Model B
Figure 6 - 2
Hard Disk Bay Cover Removal
Model C
1 2 3
Upgrading the Hard Disk Drive 6 - 5
Hard Disk Screws & Cover

The hard disks and covers pictured here may appear slightly different from your model design (these designs are subject to change and upgrade without notice). Pay careful attention to the screws (if included) and cover orientation.
4. 5. 6. 7.
Slide the hard disk in the direction of arrow 4 . Lift the hard disk out of the bay 5 . Remove the screw(s) 6 - 9 and the adhesive cover 10 . Reverse the process to install a new hard disk drive (do not forget to replace all the screws and covers).
9 8 6 10 5 7
Figure 6 - 3
Hard Disk Removal
6 - 6 Upgrading the Hard Disk Drive
Upgrading the Optical (CD/DVD) Device

The procedure for removing the optical device will depend upon your particular computer model: See Removing the Optical Device for Model A Computers on page 6 - 8. See Removing the Optical Device for Model B & C Computers on page 6 10.
Upgrading the Optical (CD/DVD) Device 6 - 7
Fan Cable & Cover

Make sure you reconnect the fan cable 5 before screwing down the bay cover. Note the information on replacing the RAM & CPU bay cover in Cover Pins on page 6 - 14.
Removing the Optical Device for Model A Computers

1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws 1 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 6 .
1 2 3 4
Figure 6 - 4
Removing the Component Bay Cover (Model A Computers)
6 - 8 Upgrading the Optical (CD/DVD) Device

5. 6. Remove the screw at point 7 , and use a screwdriver to carefully push out the optical device at point 8 . Reverse the process to install the new device.
7 8
Figure 6 - 5
Removing the Optical Device (Model A Computers)
Upgrading the Optical (CD/DVD) Device 6 - 9
Removing the Optical Device for Model B & C Computers

1. 2. 3. 4. 5. Turn off the computer, and turn it over and remove the battery. Remove the hard disk (see page 6 - 4) Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . Reverse the process to install the new device. Replace the hard disk bay cover.
Figure 6 - 6
Removing the Optical Device (Model B & C Computers)
Model B
1
Model C
1 2
Model B
Model C
6 - 10 Upgrading the Optical (CD/DVD) Device
Upgrading the System Memory (RAM)

The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDRIII (DDR3) type memory modules (see Memory on page C - 2 for details of supported module types).
1. 2. Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws 1 - 4 .
Model A
2 3 4
Model B
3 4
Figure 6 - 7
Component Bay Cover Screws
Model C
3 4
Upgrading the System Memory (RAM) 6 - 11

3.
Fan Cable
Make sure you reconnect the fan cable 5 before screwing down the bay cover.
Raise the bottom cover up to a 10 angle and carefully (a fan and cable 5 are attached to the under side of the cover) lift up the bay cover 6 .
Model A
10
Model A
6
Model B
6 5 5
Figure 6 - 8
Component Bay Cover Removal
Model C
6 5 5
6 - 12 Upgrading the System Memory (RAM)

4. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 7 & 8 ) in Figure 6 - 9.
Figure 6 - 9
7
RAM Module Release Latches
Contact Warning
5.
The RAM module will 9 pop-up, and you can remove it.
Single Memory Module Installation
9
If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket. In this case this is the lower memory socket (the socket closest to the mainboard).
Be careful not to touch the metal pins on the modules connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the modules performance.
Figure 6 - 10
RAM Module Removal
Upgrading the System Memory (RAM) 6 - 13
Cover Pins Note that the computer has four cover pins. These pins need to be aligned with slots in the case to insure a proper cover fit, before screwing down the bay cover.
6. 7.
Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30 angle and fit the connectors firmly into the memory slot. 8. The modules pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 9. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 10. Replace the bay cover by inserting it at a 10 angle and aligning the cover pins (see sidebar). 11. Make sure you reconnect the fan cable before replacing all the screws and screwing down the bay cover.
Figure 6 - 11
Cover Pin Alignment (One Model Pictured)
10
12. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.
6 - 14 Upgrading the System Memory (RAM)
Modules & Options
Chapter 7: Modules & Options

Overview
This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. PC Camera Module Wireless LAN Module Bluetooth & WLAN Combo Module 3.75G/HSPA Module Intel Rapid Storage Technology

7
Driver Installation & Module Power
Make sure any modules (e.g. WLAN, PC Camera & Bluetooth modules) are ON before installing the appropriate driver.
Overview 7 - 1
Modules & Options
Latest PC Camera Driver Information

Check the Device Drivers & Utilities + Users Manual disc, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here.
PC Camera Module
Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see Function/Hot Key Indicators on page 1 - 16) to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. When the PC Camera module is powered on, the indicator will briefly be displayed. There are a number of different camera modules available with this computer model series. You will have the appropriate application installed for your camera. Make sure you access the application via the desktop shortcut.
PC Camera Application and Power-Saving States

If the computer enters Sleep or Hibernate mode while running the camera application, the program will stop running, and will need to be restarted when the system resumes from the power-saving state.
PC Camera Driver Uninstallation

If you need to uninstall the driver, then uninstall the WebCam Installer item from the Programs and Features control panel in Windows.
7 - 2 PC Camera Module
Modules & Options
PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + Users Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install Webcam Driver > Yes. 4. Click Next > Install > Finish to restart the computer. 5. Run the camera application program from the desktop shortcut (if the hardware is turned off use the Fn + F10 key combination to turn it on again).
PC Camera Screen Refresh

The PC Camera module supports a frame rate of 12 fps. If you find that the screen refresh rate is subject to lag or stuttering, then reduce the window size, or adjust the Output Size and/or Color Space Compression. To reduce Output Size and/or Color Space Compression run the camera application, click Options and select Video Capture Pin. Adjust the settings from the appropriate pull-down menu.
PC Camera Module 7 - 3
Modules & Options

PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows.
1. 2. 3. 4. 5. 6. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone and make sure the item is not disabled. Double-click Microphone (or select Properties from the right-click menu). Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to the level required. 7. Click OK and close the control panels. 8. Run the camera application program from the desktop shortcut. 9. Go to the Devices menu heading and select Microphone (it should have a tick alongside it). 10. Go to the Capture menu heading and select Capture Audio (it should have a tick alongside it). 11. To obtain the best sound recording quality enable Noise Suppression in the Realtek HD Audio Manager control panel (see Setup for Audio Recording on page 2 - 12).
Modules & Options Figure 7 - 1

Audio Setup for PC Camera
Right-click
Modules & Options

Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format.
1. 2. 3. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check PC Camera Audio Setup on page 7 - 4) and select Start Capture. Click OK (the file location will be displayed in the pop-up box) to start capturing the video, and press Esc to stop the capture (you can view the file using the Windows Media Player).
Set Capture File Prior to capturing video files you may select the Set Capture File... option in the File menu, and set the file name and location before capture (this will help avoid accidentally overwriting files). Set the name and location then click Open, then set the Capture file size: and click OK. You can then start the capture process as above.
Note the important information in Reducing Video File Size on page 7 - 7 in order to save file space, and help prevent system problems.
Modules & Options

Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Note that the Windows system requires a minimum of 15GB of free space on the C: drive system partition. In order to prevent system problems it is recommended that you save the captured video file to a location other than the C: drive (see Set Capture File on page 7 - 6), limit the file size of the captured video or reduce video resolution (see below). To Reduce Video Resolution Output Size:
1. 2. 3. 4. Run the camera application program from the desktop shortcut. Go to Options and scroll down to select Video Capture Pin.... Click the Output Size drop box and select a lower resolution size in order to reduce the captured file size. Click OK.
Modules & Options
Latest PC Camera Driver Information

Check the Device Drivers & Utilities + Users Manual disc, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here, including the figures pictured.
Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options.
1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under PowerLine Frequency.
Camera Options
The video capture filter figure pictured here may appear slightly different for some camera modules. To adjust the anti flicker properties look under the headings Anti Flicker/Frequency/PowerLine Frequency.
Figure 7 - 2
Video Capture Filter
Modules & Options

Taking Still Pictures The camera application allows you to take still pictures.
1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The picture (in JPEG format) will be placed in the Snapshot folder desktop.
Snapshot Folder on the

The Snapshot folders default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files.
Modules & Options

Wireless LAN Module

If you have included an Intel or 3rd Party Wireless LAN (or WLAN & Bluetooth combo) module in your purchase option, make sure that the WLAN module is on before installing the driver. Use the Fn + F11 key combination (see Function/Hot Key Indicators on page 1 - 16) to toggle power to the Wireless LAN module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. When the WLAN module is powered on the indicator will briefly be displayed. Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth Combo modules.
Use the Fn + F11 key combination or hot key button to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 5, on page 1 - 16/ Table 1 - 3, on page 1 -
7 - 10 Wireless LAN Module
Modules & Options
3rd Party WLAN Driver Installation

If you see the message Found New Hardware click Cancel to close the window.
1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + Users Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Choose the language you prefer and click Next. 5. Click Next. 6. Click Finish to restart the computer.
Intel WLAN Driver Installation

If you see the message Found New Hardware click Cancel to close the window.
1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + Users Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Click Next > Next. 5. Click the button to accept the license and click Next. 6. Click Next > Next > Finish.
Note: The operating system is the default setting for Wireless LAN control in Windows (see overleaf).
Wireless LAN Module 7 - 11
Modules & Options
Network and Sharing Center

You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks.
Connecting to a Wireless Network in Windows 7

Make sure the Wireless LAN module is turned on.
1. Click the taskbar wireless icon , and then double-click an access point to connect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing setting changes, and creating a new network).
7
Figure 7 - 3
Click Taskbar Icon Menu & Network and Sharing Center
Modules & Options

2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click View or change settings in Network and Sharing Center to access further options for the connection.
Figure 7 - 4
Network Location Set
Modules & Options
Security Enabled Networks

You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
5. 6.
Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button).
Figure 7 - 5
Click Taskbar Icon Menu - Disconnect
Modules & Options
Intel My WiFi Configuration

Intel My WiFi Technology uses your WLAN (for Intel WLAN modules only) module to allow you to connect up to eight other WiFi enabled devices (e.g. digital cameras, other computers, cell phones, handheld devices etc.) to your computer (similar to Bluetooth), while still connecting to the Internet through your WiFi wireless connection. Intel My WiFi Technology offers greater range and speed than other personal area networks, and does not require an access point.
Intel My WiFi Help

To get help on Intel My WiFi configuration and settings, access the Intel My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon . Click the Help icon and select a help topic from the Contents menu.
Modules & Options

Intel My WiFi Configuration You can configure the My WiFi settings as follows.
1. Access the Intel My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon . Click Enable (on the first run of the program there will be no connected devices listed).
2.
Figure 7 - 6
Intel My WiFi Utility
Modules & Options

3. 4. 5. Click Start and click Control Panel. Click Network and Sharing Center (Network and Internet). Click Change adapter settings.
Figure 7 - 7
Network and Sharing Center Click Change adapter settings
Modules & Options

6. Right-click Wireless Network Connection and select Properties.
Figure 7 - 8
Network Connections Right-click Wireless Network Connection and select Properties.
Modules & Options

7. 8. 9. Click Sharing (tab) and select Allow other network users to connect through this computers Internet connection. Select Wireless Network Connection under Home networking connection. Click OK.
Click Allow other network users to connect through this computers Internet connection. Select Wireless Network Connection.
Figure 7 - 9
Wireless Network Connection Properties Sharing
Modules & Options

10. Access the Intel My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon . 11. Click Profiles .
Figure 7 - 10
Intel My WiFi Utility - Profiles
Modules & Options

12. Click Profiles, click Intel Wireless PAN and click Edit or New (Note that all preset settings may not be editable - see sidebar).
Figure 7 - 11
Profiles
Profile Settings 13. You can change the Profile Name and Network Name to your personal preferences in General (tab).
Profiles that are preset may not be fully editable. To edit all the profile settings, click New to create a new profile and adjust the settings to your preferences.
Profile and Network Names

The Profile Name is the name as displayed on your computer in the Network Connections control panel (see Figure 7 - 13 on page 7 - 22). The Network Name (SSID) is the name the devices see when they try to connect to your computer.
Figure 7 - 12
Intel My WiFi Profile Settings General
Modules & Options

14. Click Security (tab). 15. Change the Security Type to WEP and the Encryption Type to 64bit. 16. Enter a password (8 characters long) in the Password box.
Figure 7 - 13
Intel My WiFi Profile Settings Security
Modules & Options

17. Click Sharing (tab). 18. It is recommended that the Filter Network Traffic and DHCP and DNS Server are Disabled.
Figure 7 - 14
Intel My WiFi Profile Settings Sharing
Modules & Options

19. Click Advanced (tab). 20. It is recommended that the Default Channel is set to Channel 1, 6 or 11. 21. Click OK to save the settings.
Figure 7 - 15
Intel My WiFi Profile Settings Advanced
Modules & Options

22. Double-click Wireless Network Connection in Network Connections. 23. Click Details to display the Network Connection Details.
Figure 7 - 16
Wireless Network Connection Details
Modules & Options

24. Access the Intel My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon . 25. To add a new device follow the instructions in the devices user guide for connecting to a WiFi network. 26. Click Add New Device in Intel My WiFi Utility to confirm the security settings detail.
7
Figure 7 - 17
Intel My WiFi Utility (Add New Device)
Modules & Options
Intel WLAN & Bluetooth Combo Module High-Speed Data Transfer Configuration
You will need to configure the following settings to enable high-speed wireless data transfer as supported by Intel Wireless LAN & Bluetooth Combo modules (note this information applies to Intel WLAN & Bluetooth Combo modules only).
1. Go the Windows control panel and double-click Device Manager (in Hardware and Sound under Devices and Printers).
7
Figure 7 - 18
Devices and Printers (Device Manager)
Modules & Options

2. 3. 4. 5. 6. 7. 8. Click Network adapters to expand the sub-menu. Double-click the Intel WiFi Link .... module. Click Advanced (tab). Click 802.11n Channel Width for band 2.4 under Property:. Click the pull-down menu under Value: Click to select Auto. Click OK and close the control panels.
7
Figure 7 - 19
Intel WiFi Link Properties (Advanced)
Modules & Options

The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center:
1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Figure 7 - 20
Modules & Options

Bluetooth & WLAN Combo Module

If your purchase option includes the Combination Wireless LAN & V3.0 Bluetooth module (either Intel or 3rd Party) then install the driver as instructed overleaf. Use the Fn + F12 key combination to toggle power to the Bluetooth module. When the Bluetooth module is powered on the indicator will briefly be displayed.
Bluetooth Data Transfer

Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.
Use the Fn + F12 key combination to toggle power to the Bluetooth module, and check the LED indicator to see if the module is powered on or not (see Table 1 - 5, on page 1 - 16/ Table 1 - 3, on page 1 - 11).
For 3rd party Bluetooth combo modules see the installation procedure see 3rd Party Bluetooth Combo Driver Installation on page 7 - 31 and 3rd Party Bluetooth & WLAN Combo Settings on page 7 - 32. For Intel Bluetooth combo modules see the installation procedure see Intel Bluetooth Combo Driver Installation on page 7 - 39 and Standard Bluetooth Configuration in Windows 7 on page 7 - 40.
7 - 30 Bluetooth & WLAN Combo Module
Modules & Options
3rd Party Bluetooth Combo Driver Installation

Note this driver is required only for the combo Bluetooth and WLAN module only.
High Speed Bluetooth Data Transfer The Combination Wireless LAN & V3.0 Bluetooth module supports high speed (V3.0) data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed (V3.0) data transfer make sure that both the WLAN and Bluetooth modules are powered on. Check your Bluetooth compatible devices documentation to confirm it supports high speed data transfer.
1. Before installing the driver make sure the Bluetooth module is powered on (use Fn + F12 key combination), then insert the Device Drivers & Utilities + Users Manual disc into the CD/DVD drive. If a Found New Hardware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4. Choose the language you prefer and click OK. 5. Click Next. 6. Click the button to accept the license and click Next. 7. Click Next > (select if you want to create an icon to appear on the desktop) Next > Install. 8. Click Finish. 9. The My Bluetooth icon will appear on the desktop and the Bluetooth item will be installed in the Programs/All Programs menu. 10. See Bluetooth Networking Setup on page 7 - 35 for information on Bluetooth networking.
Bluetooth & WLAN Combo Module 7 - 31
Modules & Options
Bluetooth Module & Resuming From Sleep Mode

The Bluetooth modules default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep.
3rd Party Bluetooth & WLAN Combo Settings

This information applies to the combo Bluetooth and WLAN module only.
1. 2. 3. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (menu heading).
Figure 7 - 21
My Bluetooth Settings
Modules & Options

4. Click General Settings to change the computer name that other Bluetooth devices will see, and click the tickbox to Allow Bluetooth devices to find this computer Click OK to confirm the settings.
5.
7
Figure 7 - 22
General Settings
Modules & Options

6. 7. Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings.
7
Figure 7 - 23
File Transfer Settings
Modules & Options
Bluetooth Networking Setup

This information applies to the combo Bluetooth and WLAN module only.
1. 2. 3. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 21 on page 7 - 32).
7
Figure 7 - 24
Network Settings
4. 5. 6.
Click Network Settings (make sure the Bluetooth module is powered on. Click Enable Bluetooth Network and click OK. A message will appear in the taskbar to confirm that the network driver has been installed.
Modules & Options

Bluetooth & WLAN Combo Module Configuration

Setup your Bluetooth Device so the Computer Can Find it
1. 2. 1. 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Press the Fn + F12 key combination to power on the Bluetooth module. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Double-click the device you want to pair with the computer (if no devices appear press F5 or click the Refresh button to search for devices).
To Turn the Bluetooth Module On To Add a Bluetooth Device
Figure 7 - 25
My Bluetooth Devices
Modules & Options

3. You will then be presented with a menu of options to select from.
7
Figure 7 - 26
Bluetooth Device Options
4.
Click the appropriate button to connect to the device.
Modules & Options

5. 6. You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection.
7
Figure 7 - 27
Bluetooth Pairing Code & Connection Established
Modules & Options
Intel Bluetooth Combo Driver Installation

Note this driver is required only for the Intel combo Bluetooth and WLAN module only.
1. Before installing the driver make sure the Bluetooth module is powered on (use Fn + F12 key combination), then insert the Device Drivers & Utilities + Users Manual disc into the CD/DVD drive. If a Found New Hardware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4. Click Next > Next. 5. Click the button to accept the license and click Next. 6. Click Next > Finish.
Note that, at the time of going to press, Intel Centrino Wireless-N 1030 & Intel Centrino Wireless-N 130 WLAN & Bluetooth V3.0+HS combo modules use the standard Bluetooth configuration in Windows 7 (see over for configuration instructions). Do not use the Bluetooth & WLAN Combo settings information outlined from page 7 - 32 to page 7 - 38. See also Intel Centrino Advanced WLAN & Bluetooth V3.0+HS Combo Modules on page 8 - 17.
Modules & Options
Standard Bluetooth Configuration in Windows 7
Add a Device
Click Start, and click Control Panel and then click Devices and Printers (Hardware and Sound). Click Add a device to search for any available Bluetooth devices.
Setup your Bluetooth Device so the Computer Can Find it

1. 2. 1. 2. 3.

Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar. You can then do any of the following to access the Bluetooth Devices control panel.
Double-click the taskbar icon to access the Bluetooth Devices control panel. and choose an option from the menu. Click/Right-click the taskbar icon
To Turn the Bluetooth Module On

Add a device
Figure 7 - 28
Bluetooth Devices & Click Icon Menu
Right-Click Taskbar Icon
Modules & Options

To Add a Bluetooth Device
1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer.
Pairing Options
If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the devices existing pairing code or you can pair certain devices without using a code.
Figure 7 - 29
3. On first connection the computer will provide you with a pairing code to be entered onto the device. Add a Device
Modules & Options

4. Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing.
Figure 7 - 30
Pairing Code Example
Pairing Codes
The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing.
5. 6. 7.
Windows will check to see if any drivers are required to complete the pairing. Follow any on-screen instructions on the computer if device drivers are required to be installed. Click Close.
Figure 7 - 31
Pairing Complete & Bluetooth Device Enabled
Modules & Options

To Change Settings for the Bluetooth Device
1. 2.

Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to:
Change the name of the device (click Bluetooth, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK).
Bluetooth Help
To get help on Bluetooth configuration and settings, select Help and Support from the Start menu. Type Bluetooth in the Search Help box, and select an item from the returned search results to get more information.
To Make your Computer Discoverable to Bluetooth Devices

1. 2. 3. Click the taskbar icon and select Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it. Make sure that the Alert me when a new Bluetooth device wants to connect check box (Connections) has a tick inside it, if you want to be notified when a Bluetooth device wants to connect.
Figure 7 - 32
Bluetooth Settings Options
Modules & Options
3.75G/HSPA Module
(For Models A & B Only) If you have included an optional 3.75G/HSPA (High Speed Packet Access) module (see Communication on page C - 4 for specification details) in your purchase option, you will have the appropriate application (Wireless Manager) provided for your particular module. Follow the instructions on page 7 - 45 to install the USIM card (which will be provided by your service provider), and then install the application.
7
Important Notice - 3.75G/HSPA & Bluetooth/Wireless LAN Modules
In order to comply with FCC regulations you should NOT operate the 3.75G/HSPA module and the Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3.75G/HSPA module is powered on, make sure that the Bluetooth/Wireless LAN modules are powered off.
7 - 44 3.75G/HSPA Module
Modules & Options

1. 2. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Locate the 3.75G USIM card cover and loosen screw 1 , and then remove the USIM card cover 2 .
Figure 7 - 33
USIM Card Cover Removal
2
3. 4. 5. Insert the USIM card as you would into your mobile phone. Slide the SIMLOCK towards the hinge in order to release the lock and lift it up. Insert the USIM card as illustrated in (Figure 7 - 34) and close the SIMLOCK.
Power Safety Warning
Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.
Figure 7 - 34
Insert the USIM Card
3.75G/HSPA Module 7 - 45
Modules & Options

6. Lock the SIMLOCK by pushing it in the direction of the arrow in Figure 7 - 35 until it clicks into the lock position.
Figure 7 - 35
SIMLOCK Lock
3.75G/HSPA Modules & System Wake Up
Note that the 3.75G modules DO NOT support system wake up on 3.75G/HSPA modem activity.
Modules & Options

Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see Table 1 - 5, on page 1 - 14) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that exiting the application does NOT turn off the 3.75G/HSPA module. Wireless Manager - See Wireless Manager Installation on page 7 - 48 for driver installation information and Wireless Manager Application on page 7 - 49 for instructions on using Wireless Manager.
Modules & Options
Wireless Manager

With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the Wireless Manager application. The Wireless Manager application allows you to directly access your HSPA internet service from the computer.
Use the Fn + key combination to toggle power to the 3.75G/HSPA module, and check the indicator to see if the module is powered on or not (see Table 1 - 5, on page 1 - 12/ Table 1 - 3, on page 1 - 9).
Wireless Manager Installation 1. Enable power to the module by pressing the Fn + key combination (give the module about 10 seconds to power on - the on screen icon will indicate the modules power status). 2. If a Found New Hardware window appears, click Cancel (click Cancel for all Found New Hardware windows that appear). 3. Insert the Device Drivers & Utilities + Users Manual disc into your external optical device drive. 4. Click Option Drivers (button). 5. Click 4.Install 3G Driver > Yes. 6. Click Next > Next > Install. 7. Click Finish. 8. Access the Wireless Manager application from the Start menu or the desktop shortcut .
Modules & Options
Wireless Manager Application

The connection information is stored on the USIM card supplied by the service provider (where this is not the case you may need to create a profile - see Creating a Profile on page 7 - 55).
1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . You may be required to enter you PIN number and click OK. Click the Connect button (a Profile needs to be selected, and in most cases this will be pre-configured).
PIN Number
The PIN number for your USIM card will be supplied by your service provider. You usually have a limited number of attempts to enter the correct PIN number. If you fail to enter the PIN number correctly you will be blocked from accessing the USIM card and you will need a PUK (Personal Unblocking Key), supplied by your service provider, to unlock it.
Figure 7 - 36
Wireless Manager (Not connected)
Modules & Options
Wireless Manager Help

To get help on Wireless Manager configuration and settings, click the Help icon or press F1.
5. 6. 7.
The system will connect to your network. Connected will appear above the timer icon (the timer will indicate your connected time for the current session) . You can then access the internet, download e-mail etc. as per any internet connection.
Figure 7 - 37
Wireless Manager (Connected)
Modules & Options

8. Click the Wireless Manager notification area icon to view the connection status, or wireless icon to view the Mobile Broadband Connection status.
Figure 7 - 38
Notification Area Icons (Connected)
9. 10. The indicator will display the signal strength and radio access technology. To disconnect from the service provider, click the Disconnect button (note that if you click the close icon at the top right of the screen the application will minimize to the system tray, however the application will still be running; to exit the application right-click the notification area icon and click Disconnect or Exit Wireless Manager). The program will disconnect from the service provider. key combination The module will still be on, and you will need to press the Fn + to turn it off. If you are unsuccessful in connecting this way you may need to add a profile with information provided by your service provider (see the following pages). Notification Area Icon
Right-click the notification area icon to bring up the menu to Open/Exit Wireless Manager, Disconnect or Turn radio off.
11. 12. 13.
Modules & Options
Profiles
1. 2. 3. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click the Settings > Advanced. Click the Profiles (tab).
Figure 7 - 39
Advanced Settings Profiles
Modules & Options

4. Multiple profiles may be available from the USIM card and the first time the application starts it may require you to select a profile (Set Profile) to use for your connection.
Figure 7 - 40
Multiple Profiles Found
Automatic Profile Selection If Automatic selection is chosen, then the application will search the operator profile database for a profile that matches the details on your USIM card. If a correct profile is found it will be automatically selected as your profile. Manual Profile Selection If Manual selection is chosen, then you can select a profile from the applicationss operator profile database, or you can create a new profile.
Modules & Options

Selecting a Profile
1. 2. 3. Click Manual selection (button). Click the Filter to view the drop-down list. Select the Profile you wish to use and click Apply to confirm the selection.
Figure 7 - 41
Profile - Manual Selection (Filter)
Modules & Options

Creating a Profile
1. 2. 3. 4. 5. 6. 7. 8. Click Manual selection (button). Click the New. Enter a name you prefer for the profile. Enter the Access Point Name (APN). Enter the User Name and Password if required (some service providers may not require this information and the fields may then be left blank). If your service provider requires IP address, DNS and Protocols to be entered, click the appropriate tab and enter the supplied information (otherwise leave blank). Click Save to save the profile information. The profile will be stored under User defined in the Filter drop-down list.
Deleting a Profile
To delete a profile click to select Manual selection and select the profile and click Delete.
Modifying a Profile
To modify a profile click to select Manual selection and select the profile and click Edit. Change the settings as required and then click Save (note that only user defined profiles may be edited).
Figure 7 - 42
New Profile IP, DNS & Protocols
Modules & Options
Settings
The Settings tab allows you at adjust the application features. Click to put a tick in Launch Wireless Manager at Windows startup to launch the application at Windows Startup.
Figure 7 - 43
Settings
The Advanced settings allows more detailed configuration. To access the Advanced settings:
1. 2. 3. Access the Wireless Manager program from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click the Settings > Advanced. Click the tab to edit any particular setting.
Modules & Options

SIM Most USIM cards are protected by a Personal Identity Number (PIN). You may turn on or off the Request PIN at startup (click Apply to save any changes). You can also Change PIN (you will need to enter the new PIN in the two fields provided and click Apply to save any changes). Radio Radio needs to be turned on before you can make any connection (note this is not the same as powering the module off/on using the Fn + key combination), but you may turn it off when required. Automatic mode is the recommended setting for most 3G networks as it will use 3G where available. All Frequency bands are selected as default (click Apply to save any changes).
PIN Notes
You will have to enter your current PIN to change the PIN settings. Request PIN at startup will apply only after you have shut the computer down and restarted it (not just restarted).
Radio & Power Saving States

You can choose to have the radio turned on or off during Hibernate or Sleep power saving states.
Figure 7 - 44
Advanced Settings SIM & Radio
Modules & Options
Warning Note that some applications automatically transmit data when connected, and you may be charged for the data transfer. Some auto connection/connection settings may lead to expensive roaming charges.
Networks The mobile network list lists available networks at your location, and allows you to select a network which to connect. You must disconnect before being able to select a network. Connection You can set the Wireless Manager to automatically connect at Windows startup (however the module must be powered on, and radio must be turned on). You can also automatically connect when resuming from a power-saving state (click Apply to save any changes). Click Default to return to the original default settings.
Figure 7 - 45
Advanced Settings Networks & Connection
Modules & Options
Text Messaging Service (SMS)

In addition to standard internet services you may also send and receive SMS text messages using the Wireless Manager, if your service supports SMS.
SMS Utility
1. 2. 3. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. The indicator in the upper right corner will display if radio is currently on or off (radio must be on in order to send/receive messages).
Figure 7 - 46
SMS Utility Open
Modules & Options

Messages Click the Messages tab to access the tabs displaying text messages. The tabs at the top of the menu display the Inbox, Drafts, Outbox, Sent and Trash menus.
Inbox
Drafts Outbox
Sent
Trash
Figure 7 - 47
SMS Utility Messages
Text messages are automatically saved to your computer and may be sorted in ascending or descending order by name or date.
Modules & Options
Sending a Text Message

1. 2. 3. 4. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. Click the New Message tab. Enter the phone number in the To field (multiple numbers may be entered to select a name from separated by a semicolon (;), or click the phonebook icon the phonebook. Select any contacts phone number and click OK (you can click a check box to select multiple contacts or more than one phone number for each contact). Type the message body in the Message field (to a maximum of 160 characters).
5. 6.
Figure 7 - 48
SMS Utility - New Message
Modules & Options

7. 8. 9. Click Send to send the message or Save to save the message in the Drafts folder. clears both the Message and To fields. Clicking the Clear icon If radio is on then the message will be sent, however if the radio is off the message will be stored in the Outbox.
Note that you do not have to connect to the network to Send/Receive SMS messages.
Inbox Any received text messages will be displayed in the Inbox. The number of unread messages will be displayed in parenthesis in the inbox tab. Unread messages will be displayed in a darker color then the read messages, and incoming messages will be displayed briefly in the Notification Area.
Figure 7 - 49
SMS Utility - Inbox & New Message Received Notification
Modules & Options

Messages Opening a text message: Double-click the message and the message will open in a new window (to close it click the close icon in the top right of the message).
Figure 7 - 50
Click to close the message
Close Message
Previewing a text message: Click the preview icon will open. Click the icon again to close the preview.
and the message preview
Replying to a text message: Double-click the message and click Reply. Type the reply in the message field and click Send to send the message (or Save to save it in Drafts. Forwarding a text message: Double-click the message and click Forward. Type the recipients name in the To field or click the icon to select recipients from the phonebook. Deleting a text message: Right-click the message select Delete selected. To delete al messages in the folder right-click any message and select Delete All. Holding down the Ctrl key and selecting messages allows you to multiple select messages for deletion (choose Delete selected). Deleted message will be sent to the Trash folder. To permanently delete messages right-click and select Delete selected or Delete All (or you may choose to Recover/Recover All) and click Yes to confirm.
Modules & Options
Phonebook
The Phonebook allows you to view and edit all your frequently used contacts, and is divided into Contacts and Groups . To access the Phonebook:
1. 2. 3. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. Click the Phonebook tab.
7
Figure 7 - 51
SMS Utility Phonebook (Contacts)
Modules & Options

Contacts
New Contact: Click the New contact button to create a contact. Add the name and at least one phone number (Mobile, Work, Home and Other fields are available) for the contact. Click the icon to expand the number details. Select Synchronize with SIM to synchronize the contact information with your USIM card. Click the Save icon to save the information.
Import/Export Contacts
Import/Export Contacts: Click the Import/ Export buttons to import or export the list of contacts.
Figure 7 - 52
SMS Utility New Contact
Edit Contact: Click the edit icon to make changes to a contact detail, and click save to confirm the changes. Delete Contact: Click the delete icon to delete a contact from the phonebook. Send a message to a Contact: Click the message icon to send a text message to any contact.
Modules & Options

Groups You can organize existing contacts into groups from the Groups tab.
New Group: Click the New group button to create a group. Click the icon to expand the group details, and click a check box to add at least one phone number from the contacts for the group. Click the Save icon to save the information.
Figure 7 - 53
SMS Utility Groups
Edit Group: Click the edit icon to make changes to a contact detail, and click save to confirm the changes, or close to exit without making changes. Delete Group: Click the delete icon to delete a group from the phonebook. to send a text message
Send a message to a Group: Click the message icon to any group.
Modules & Options
SMS Settings
The SMS Utility Settings tab allows you at adjust the SMS features.
Figure 7 - 54
SMS Utility Settings
SMS Settings
Message Length: You can set the number of blocks that can be sent (up to a length of 10 blocks). Message validity period: This sets the period after which the message will be deleted from the SMS center and therefore not forwarded to the recipient(s) when they come online. Display information messages: You can choose whether to allow information messages to automatically appear on screen or not.
The Advanced settings allows more detailed configuration. To access the Advanced settings:
1. 2. 3. 4. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. Click the Settings > Advanced. Click the tab to edit any particular setting.
Modules & Options

Send Click Delivery Report to automatically request a reply from a recipient. If you click to Send messages in Outbox automatically upon connection then messages written when the radio is off, will then be sent automatically the next time radio is turned on. You can also choose to Include original message in reply. Notification This menu allows you to enable/disable Show animation on new message to get an animated notification of newly received messages. Enabling Play sound on new message will play an audio notification upon receipt of new messages.
7
Figure 7 - 55
SMS Utility Advanced Settings Send & Notification
Modules & Options

Number You can choose to Use default service center number or you can uncheck the box and add your number manually if your service provider supplies a different number (click Apply to save the change or Default to return to the default number). Memory Phonebook memory status displays the number of contacts displayed on the USIM card.
7
Figure 7 - 56
SMS Utility Advanced Settings Number & Memory
Modules & Options
Intel Rapid Storage Technology

Install the Intel Rapid Storage Technology to support your SATA drive if set up in AHCI mode in the BIOS (see SATA Mode (Advanced Menu) on page 5 - 8).
IRST Driver Installation 1. Insert the Device Drivers & Utilities + Users Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 6.Install IRST Driver > Yes. 4. Click Next > Yes > Next > Next. 5. Click Finish to restart the computer (you will need to restart the system again after the computer has rebooted).
7 - 70 Intel Rapid Storage Technology
Troubleshooting
Chapter 8: Troubleshooting
Overview
Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This cant anticipate every problem, but you should check here before you panic. If you dont find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface. If all else fails, talk to your service representative. You should also make a record of what happened and what remedies you tried. Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview this section just in case. If, after youve tried everything, and the system still wont cooperate, try turning it off for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call your service representative.
Overview 8 - 1
Troubleshooting
Basic Hints and Tips

Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see LED Indicators on page 1 - 11) to see the computers power status. Connections - Check all the cables to make sure that there are no loose connections anywhere. Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys configured in your Power Options (see Power-Saving States on page 3 - 6), the Fn + F4 key combination, or power button to wake-up the system.
Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the brightness. Display Choice - Press Fn + F7 to make sure the system is not set to external only display. Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive (this is a common cause of the message Invalid system disk - Replace the disk, and then press any key / Remove disks or other media. Press any key to restart).
8 - 2 Basic Hints and Tips
Troubleshooting
Backup and General Maintenance

Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Dont forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer. You can use those that are provided free with your OS, or buy the more powerful dedicated programs to do so. Write down your passwords and keep them safe (away from your computer). This is especially important if you choose to use a Supervisor password for the BIOS (see The Setup Utility on page 5 - 2). Keep copies of vital settings files such as network, dialup settings, mail settings etc.(even if just brief notes).
Warranty
The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty.
Backup and General Maintenance 8 - 3
Troubleshooting
Viruses
Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. Be careful when opening e-mail from sources you dont know. Viruses are often triggered from within email attachments so take care when opening any attached file. You can configure most Anti-Virus programs to check all e-mail attachments. Note: You should also beware of files from people you know as the virus may have infected an address book and been automatically forwarded without the persons knowledge.
Keep a Bootable CD-ROM/DVD-ROM/USB storage device (this CD/DVD/USB device provides basic information which allows you to startup your computer) handy. You may refer to your OSs documentation for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at least instructions on how to make one).
8 - 4 Viruses
Troubleshooting
Upgrading and Adding New Hardware/Software

Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. Dont open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. Read the documentation. We can assume, since you are reading this that you are looking at the computers manual, but what about any new peripheral devices you have just purchased? Many problems are caused by the installation of new hardware and/or software. Always refer to the documentation of any new hardware and/or software, and pay particular attention to files entitled READ ME or READ ME FIRST. When installing a new device always make sure the device is powered on, and in many cases you will need to restart the computer. Always check that all the cables are correctly connected. Make sure you have installed the drivers for any new hardware you have installed (latest driver files are usually available to download from vendors websites).
Upgrading and Adding New Hardware/Software 8 - 5
Troubleshooting
Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. Dont over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and removing devices and restarting where necessary) will often find the source of a problem, although this may be time consuming.
8 - 6 Upgrading and Adding New Hardware/Software
Troubleshooting
Problems and Possible Solutions

Problem
You turned on the power but it doesnt work. The battery LED power indicator blinking orange. , is
Possible Cause - Solution

Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure theres nothing interfering with the battery contacts. Low Battery. Plug in the DC power source. If the computer doesnt start up immediately, turn it off then on again. The system is using too much power. If your OS has a Power Options scheme (see Power Plans on page 3 - 4) check its settings. You may also be using a USB device/external device that is drawing a lot of power. The battery has not been fully discharged before being recharged. Make sure the battery is fully discharged and recharge it completely before reusing (see Battery Information on page 3 - 11). Power Options have been disabled. Go to the Control Panel in Windows and re-enable the options. A peripheral device/USB device is consuming a lot of power. Turn off/remove the unused device to save power.
You are losing battery power too quickly.
Actual battery operating time is shorter than expected.
Problems and Possible Solutions 8 - 7
Troubleshooting
Problem
The computer feels too hot.

Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesnt cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isnt sitting on a thermal surface (see Overheating on page 1 - 24). Make sure youre using the correct adapter. Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vent/Fan intakes to be blocked.
Nothing appears on screen.
The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see Configuring the Power Buttons on page 3 - 8). The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If youre connected to an external monitor, make sure its plugged in and turned on. You should also check the monitors own brightness and contrast controls. The computer is set for a different display. Toggle the screen display key combination, Fn + F7. If an external monitor is connected, turn it on. The screen saver is activated. Press any key or touch the Touchpad.
No image appears on the external monitor I have plugged in and powered on.
You havent installed the video driver and configured it appropriately from the Control Panel. See Appendix B for instructions on installing and configuring the video driver.
8 - 8 Problems and Possible Solutions
Troubleshooting
Problem
You forget the boot password.

If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help.
Password Warning
If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
The sound cannot be heard or the volume is very low. The CD/DVD cannot be read. The CD/DVD tray will not open when there is a disc in the tray. The DVD regional codes can no longer be changed. Unwelcome typing. numbers appear when
The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows taskbar, or use the key combination Fn + F5 and F6 (see Function/Hot Key Indicators on page 1 - 16) to adjust. The CD/DVD is dirty. Clean it with a CD/DVD cleaner kit. The CD/DVD is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see Loading Discs on page 2 - 3). The code has been changed the maximum 5 times. See DVD Regional Codes on page 2 - 5. If the LED page 1 - 11). is lit, then Num Lock is turned ON. (see LED Indicators on
Troubleshooting
Problem Possible Cause - Solution
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the systems regular keyboard may not work.
The system freezes or the screen goes dark.
The systems power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see Power-Saving States on page 3 - 6). Make sure you have enabled Hibernate mode from the control panel. The modules are off. Check the LED indicator and/or function key indicator to see if the WLAN/Bluetooth module is on or off (see LED Indicators on page 1 - 11). If the LED indicator is off, then press the Fn + F11 (WLAN) or Fn + F12 (Bluetooth) key combination(s) in order to enable the modules (see Table 1 - 5, on page 1 - 16).
The system never goes into a power saving mode.
The Wireless LAN or Bluetooth modules cannot be detected.
8 - 10 Problems and Possible Solutions
Troubleshooting
Problem
The PC Camera module cannot be detected. The Wireless LAN/Bluetooth/ PC Camera modules cannot be configured. A file cannot be copied connected Bluetooth device. to/from a

The module is off. Press the Fn + F10 key combination in order to enable the module (see Function/Hot Key Indicators on page 1 - 16). Run the camera application to view the camera picture. The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in Modules & Options on page 7 - 1). The transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the device to your computer until the file transfer process from the computer has been completed. The Bluetooth modules default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep. There are different Touchpad versions available on this computer, and this version requires tapping/holding to scroll. Either tap repeatedly, or hold the finger down, at the top or bottom right of the Touchpad (depending on the scrolling direction required) to scroll the window.
The Bluetooth module resuming from Sleep.
is
off
after
I am sliding my finger up and down on the right side of the Touchpad to scroll a Window and the Touchpad does not respond.
Troubleshooting
Bluetooth Connection Problems

If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver.
1. 2. 3. 4. 5. Install the Microsoft Windows Device Center Driver as appropriate for your operating system. Windows Vista will automatically configure the driver for you, however Windows 7 requires further configuration. Make sure the Bluetooth device is powered on. Go the Windows 7 control panel and double-click Device Manager (Hardware and Sound > Devices and Printers). Bluetooth Peripheral Device(s) will be listed under Other Devices (note this will only be listed if you have connected, or tried to connect to, a Bluetooth device previously).
Bluetooth Peripheral Devices

You will need to repeat the procedure listed here for all Bluetooth Peripheral Devices listed under Other Devices i.e. until there are no more Bluetooth Peripheral Devices listed under this menu heading.
Figure 8 - 1 - Device Manager 8 - 12 Bluetooth Connection Problems
Troubleshooting
6. 7. 8. Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer.
Figure 8 - 2 - Browse my computer.../Let me pick from...

9. Select Bluetooth Radios from the list.
Figure 8 - 3 - Select Bluetooth Radios Bluetooth Connection Problems 8 - 13
Troubleshooting
10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list.
8
Make sure you select Microsoft Corporation
Figure 8 - 4 - Select Device Driver

13. Click Next > Yes and the driver will install. 14. Click Close to complete the installation.
8 - 14 Bluetooth Connection Problems
Troubleshooting
15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Figure 8 - 5 - Device Manager - Bluetooth Radio
Bluetooth Connection Problems 8 - 15
Troubleshooting
Intel Centrino Advanced WLAN & Bluetooth V3.0+HS Combo Modules

Note that, at the time of going to press, Intel Centrino Wireless-N 1030 & Intel Centrino Wireless-N 130 WLAN & Bluetooth V3.0+HS combo modules use the standard Bluetooth configuration in Windows 7 (see Standard Bluetooth Configuration in Windows 7 on page 7 - 40). Do not use the Bluetooth & WLAN Combo settings information outlined from page 7 - 32 to page 7 - 38.
Driver Release Update Note also that, at the time of going to press, this module does not support high speed Bluetooth (V3.0) data transfer.
8 - 16 Intel Centrino Advanced WLAN & Bluetooth V3.0+HS Combo Modules
Appendix A: Interface (Ports & Jacks)

Overview
The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) A - 1
Notebook Ports and Jacks

Item
Card Reader Port
Description
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. Plug the supplied AC/DC adapter into this jack to power your computer.
DC-In Jack
External Monitor (VGA) Port
This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
HDMI-Out Port
A
Headphone-Out Jack
The HDMI-Out (High-Definition Multimedia Interface) is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device by means of a HDMI cable. Note that HDMI carries both audio and video signals. Headphones or speakers may be connected through this jack. Note: Set your systems volume to a reduced level before connecting to this jack.
Microphone-In Jack
Plug an external microphone in to this jack to record on your computer.
A - 2 Interface (Ports & Jacks)

Item
RJ-45 LAN Jack
Description
This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Security Lock Slot
To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device). The USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. USB 3.0 will transfer data much faster than USB 2.0, and is backwards-compatible with USB 2.0. Note that the USB 3.0 port (Model C Only) requires a driver installation (see USB 3.0 on page 4 - 7) and does not support wake on USB.
USB 2.0/1.1 Ports
USB 3.0 Port (for Model C Only)
Interface (Ports & Jacks) A - 3
A - 4
Appendix B: Video Driver Controls

The basic settings for configuring the LCD are outlined in Video Features on page 1 - 26.
Video Card Options

Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.
Video Driver Installation

Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
1. Insert the Device Drivers & Utilities + Users Manual disc and click Install Drivers (button). 2. Click 2.Install VGA Driver > Yes. 3. Click Next > Yes > Next > Next. 4. Click Finish to restart the computer.
Note: After installing the video driver go to the Display/Display Settings control panel to adjust the video settings to the highest resolution.
DVMT Notes
DVMT is not local video memory. DVMT will not function in MS-DOS. DOS uses the legacy memory indicated.
Dynamic Video Memory Technology

Intel DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the operating system.
Video Driver Installation B - 1
Application Mode
Note that all figures pictured, and instructions outlined here are based on the Advanced Application Mode.
Intel Graphics & Media Control Panel

Advanced video configuration options are provided by the Intel Graphics and Media Control Panel. To access the control panel:
1. 2. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button). Right-click the desktop and select Graphics Properties from the menu. Double-click the Intel(R) G&M control panel in Windows. Choose the application mode (Basic, Advanced or Wizard) required (see sidebar).
OR
3.
OR
4. 5.
Figure B - 1
Intel G&M Control Panel
B - 2 Intel Graphics & Media Control Panel

You may make changes to any of the graphics properties by clicking the appropriate menu tab on the left of the menu and adjusting the settings on the right.
Options & Support

Click Options & Support and select an item from the sub-menu to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links.
Multiple Display
At least one other display must be attached in order to view multiple display selection options.
Figure B - 2
Intel G&M Control Panel Tabs
Intel Graphics & Media Control Panel B - 3
Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: Notebook Only External Display Only Notebook + External Display Make sure you give the displays enough time to refresh. Note that HDMI supports video and audio signals.
Display Devices & Options

Besides the built-in LCD you can also use an external monitor/flat panel display/TV connected to the external monitor port or to the HDMI-Out port (High-Definition Multimedia Interface) as your display device. The table below outlines the display options.
Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the displays auto adjust/configure controls, or the Intel(R) G&M control panel to configure the full screen display.
Intel Display Mode

Single Display Clone Displays
Description
One of the connected displays is used as the display device Both connected displays output the same view and may be configured independently Both connected displays are treated as separate devices, and act as a virtual desktop
B
Table B - 1
Display Modes
Extended Desktop
B - 4 Intel Graphics & Media Control Panel
Attaching Other Displays

If you prefer to use a monitor or flat panel display, connect it to the external monitor port or HDMI-Out port on the left of the computer.
To Clone Displays:
1. 2. 3. 4. 5. Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Clone Displays from the menu. Click Apply, and OK to confirm the settings change. You can switch the Primary/Secondary Display from the menu.
Multiple Display
At least one other display must be attached in order to view Multiple Display selection options.
General Settings
Click General Settings to access settings the options for any attached display.
Figure B - 3
Display > Multiple Displays (Clone)
Attaching Other Displays B - 5

To Enable Extended Desktop:
Display Settings Extended Desktop

You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. You can drag the monitor icons to match the physical layout of your displays. Icons and programs may also be dragged between the displays.
1. 2. 3. 4.
Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Extended Desktop from the menu. Click Apply, and OK to confirm the settings change.
Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g. the secondary display may be extended left/right/above/below the primary display). Click General Settings to make any adjustments required.
B
Figure B - 4
Display > Multiple Displays (Extended)
B - 6 Attaching Other Displays

Display Profiles You can save display settings to be loaded at any time.
1. 2. 3. 4. 5. 6. 7. Go to the Intel(R) G&M control panel and click Display. Configure the General Settings, Multiple Displays, Color Enhancement, Custom Resolution & Monitor/TV Settings to your preferences. Click Apply, and OK to confirm the settings change. Click the Save button at the top of the General Settings, Multiple Displays or Color Enhancement menus (under Display Profiles). Type a name for the Profile and click OK. The Profile will be listed under Display Profiles. Select the profile from the pull-down menu and click Apply, and OK to confirm the settings change.
Figure B - 5
Intel G&M Profiles
Attaching Other Displays B - 7
Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: Notebook Only External Display Only Notebook + External Display Make sure you give the displays enough time to refresh. Note that HDMI supports video and audio signals.
Configuring an External Display in Windows 7

You can also use the Screen Resolution control panel in Windows 7 to configure an external display.
1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see Video Features on page 1 26). Click the Detect button. The computer will then detect any attached displays.
Figure B - 6
Screen Resolution Multiple Displays (Win 7)
B - 8 Configuring an External Display in Windows 7

5. You can configure the displays from the Multiple Displays menu.
Figure B - 7
Screen Resolution Multiple Display Options (Win 7)
Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) Extend these displays - Treats both connected displays as separate devices Show desktop only on 1/2 - Only one of your displays is used.
Configuring an External Display in Windows 7 B - 9

Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7.
1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on. + P key combination. Press the An on-screen menu will pop up. + P) to select the appropriate configuration from the Use the cursor keys (or menu, and press Enter to confirm the selection.
Figure B - 8
+ P Display Configuration Selection (Win 7)
B - 10 Configuring an External Display in Windows 7
HDMI Audio Configuration

HDMI (High-Definition Multimedia Interface) carries both audio and video signals. Configure the audio output as per the instructions below.
1. 2. 3. 4. Connect a device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound), and click Playback (tab). Depending on your display, the playback device may be selected automatically; however in some cases you may need to select the audio device and click Set Default (button).
Figure B - 9
Sound - HDMI Device (Set Default)
HDMI Audio Configuration B - 11

5. 6. Double-click the connected HDMI device (or right-click and select Properties) to adjust the HDMI settings from the control panel tabs. Click OK to close the control panel (see notes overleaf).
Figure B - 10
HDMI Device Properties
B - 12 HDMI Audio Configuration

HHDMI Notes
Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. To play audio sources through your external displays (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual).
HDMI Video Configuration
1. 2. 3. 4. Connect an HDMI cable from the HDMI-Out port to your external display. Configure your external display as per the instructions in Attaching Other Displays on page B - 5. Set up your external display (TV or LCD) for HDMI input (see your display device manual). You can now play video/audio sources through your external display.
Other Applications
If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the applications documentation to see the appropriate audio configuration (the application must support digital to analog translation).
HDMI Audio Configuration B - 13
B - 14
Specifications
Appendix C: Specifications
Latest Specification Information

The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications C - 1
Specifications
Processor
Note all processor packages are rPGA988B Intel Core i7-2620M (2.7GHz) 4M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel Core i5-2540M (2.6GHz) 3M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel Core i5-2520M (2.5GHz) 3M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel Core i5-2410M (2.3GHz) 3M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel Core i3-2330M (2.2GHz) 3M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W
Processor
Intel Pentium B950 (2.10GHz) 2M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel Pentium B940 (2.00GHz) 2M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel Celeron B810 (1.60GHz) 2M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W
Display
Model A: 14.0 / 35.56cm HD (1366 * 768), 16:9 Panel Model B: 15.6 / 39.62cm HD (1366 * 768) / HD+ (1600 * 900), 16:9 Panel Model C: 17.3 / 43.94cm 16:9 HD+ (1600 * 900) TFT LCD
Core Logic
Intel HM65 Express Chipset
Memory
Dual Channel DDRIII (DDR3) Two 204 Pin SO-DIMM sockets supporting DDR3 1066 MHz / 1333MHz (real operational frequency depends on the FSB of the processor) Memory Expandable up to 8GB (using 1GB/2GB/4GB SO-DIMM Modules)
Intel Core i3-2310M (2.1GHz) 3M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W
C - 2 Specifications
Specifications
Video
Intel Integrated GPU (Intel GMA HD 3000): High Preference 3D/2D Graphic Accelerator DVMT Shared Memory Architecture up to 1748MB Microsoft DirectX10 Compatible
Keyboard, Pointing Device & Buttons

Isolated A4 Size Keyboard Built-in Touchpad with Multi-Gesture Functionality
Card Reader
Embedded Multi-In-1 Card Reader - MMC/ RS MMC - SD/ Mini SD / SDHC/ SDXC - MS/ MS Pro/ MS Duo Note: Some of these cards require PC adapters that are usually supplied with the cards.
Interface
One Headphone-Out Jack One Microphone-In Jack One HDMI Out Port One External Monitor Port One RJ-45 LAN Jack One DC-In Jack Models A & B: Three USB 2.0 Ports Model C: Two USB 2.0 Ports One USB 3.0 Port
BIOS
One 32Mb SPI Flash ROM AMI BIOS
Slot
Models A & B: Two Mini-Card Slots with PCIe & USB Interfaces: Slot 1 for WLAN Module Slot 2 for 3.75G Module (Factory Option) Model C: One Mini-Card Slot with PCIe & USB Interfaces: Slot 1 for WLAN Module
Storage
One Changeable 12.7mm(h) Super Multi/ Blu-ray Combo Optical Device Drive with SATA Interface (Factory Option) One Changeable 2.5" / 9.5 mm (h) HDD with SATA (Serial) Interface
Audio
High Definition Audio Interface Built-In Microphone 2 * Built-In Speakers 3D Enhanced Stereo System
Specifications
Communication
300K / 1.3M / 2.0M Pixel PC Camera Module with USB interface (Factory Option) Built-In 10/100/1000Mb Base-TX Ethernet LAN 3rd Party WLAN 802.11b/g/n Half MiniCard Module (Factory Option) 3rd Party Combo WLAN (802.11b/g/n) and Bluetooth v3.0+HS Half Mini-Card Module with PCIe Interface (Factory Option) Intel Centrino Wireless-N 1030 (1*2 802.11 b/g/n) Half Mini-Card PCIe WLAN & Bluetooth 3.0 Combo Module (Factory Option)
Communication
Models A & B: Intel Centrino Wireless-N 100 (1*1 802.11 b/g/n) Half Mini-Card PCIe WLAN Module (Factory Option) Intel Centrino Wireless-N 130 (1*1 802.11 b/g/n+) Half Mini-Card PCIe WLAN & Bluetooth 3.0 Combo Module (Factory Option) UMTS/HSPDA-based 3.75G Module with Mini-Card Interface (Factory Option) Quad-band GSM/GPRS (850 MHz, 900 MHz, 1800 MHz, 1900 MHz) UMTS WCDMA FDD (2100 MHz) Note that UMTS modes CAN NOT be used in North America
Power
Full Range AC/DC Adapter AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 3.42A or 18.5V, 3.5A (65 Watts) Removable 6 Cell Smart Lithium Ion Battery Pack 48.84WH Removable 6 Cell Smart Lithium Ion Battery Pack 62.16WH (Factory Option) Models A & B: Removable 4 Cell Smart Lithium Ion Battery Pack 32.56WH (Factory Option)
Security
Security (Kensington Type) Lock Slot BIOS Password
Power Management
Supports Wake on LAN Supports Wake on USB Energy Star 5.0
Indicators
LED Indicators - Power/Suspend, Battery, HDD/ODD, Bluetooth/Wireless LAN, Num Lock, Caps Lock, Scroll Lock For some Model A designs in this series: HDD/ODD, Bluetooth
Specifications
Design Feature
IMR (Injected Molded Resin) LCD Back Covers (For some Model designs in this series) Special Paint or Texture ID (For some Model designs in this series)
Dimensions & Weight

Model A: 340mm (w) * 238mm (d) * 13.9 - 31.8mm (h) 2.2 kg with 48.84WH Battery & ODD For Some Model A Designs: 341mm (w) * 238.5mm (d) * 16 - 34mm (h) 2.2 kg with 48.84WH Battery & ODD Model B: 374mm (w) * 250mm (d) * 14.3 - 34.1mm (h) 2.3 kg with 48.84WH Battery & ODD For Some Model B Designs: 374mm (w) * 250mm (d) * 14.3 - 35.3mm (h) 2.3 kg with 48.84WH Battery & ODD 374mm (w) * 250mm (d) * 20 - 37.2mm (h) 2.6 kg with 48.84WH Battery & ODD Model C: 413mm(w) * 270mm(d) * 14 - 40.5mm(h) 2.9kg with ODD & 48.84WH Battery
Operating System
Windows 7 with Service Pack 1
Environmental Spec
Temperature Operating: Non-Operating: Relative Humidity Operating: Non-Operating: 5C - 35C -20C - 60C 20% - 80% 10% - 90%
Specifications

Manual Da Placa W240HU-W250HUQ

Uploaded by

Copyright:

Available Formats

Manual Da Placa W240HU-W250HUQ

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual Da Placa W240HU-W250HUQ

Uploaded by

Copyright:

Available Formats

V11.1.

EuP-Standby and Off Mode Power Consumption Statement:

Operation is subject to the following two conditions:

FCC RF Radiation Exposure Statement:

IMPORTANT SAFETY INSTRUCTIONS

This Computers Optical Device is a Laser Class 1 Product

Instructions for Care and Operation

Take care when using peripheral devices.

Polymer Battery Precautions

Developing Good Work Habits

LCD Screen Care

LCD Electro-Plated Logos

Quick Start Guide

Features & Components

Drivers & Utilities

Upgrading The Computer

Modules & Options

Interface (Ports & Jacks)

Video Driver Controls

Quick Start Guide

Chapter 1: Quick Start Guide

Quick Start Guide

Beginners and Not-So-Advanced Users

Quick Start Guide

Ports and Jacks

Quick Start Guide

Quick Start Guide

Quick Start Guide

Model A 14.0 / 35.56cm HD (1366 * 768), 16:9 Panel

Model C 17.3 / 43.94cm 16:9 HD+ (1600 * 900) TFT LCD

413mm(w) * 270mm(d) * 14 - 40.5mm(h) 2.9kg with ODD & 48.84WH Battery

Quick Start Guide

System Map: LCD Panel Open - Model A Design I

Wireless Device Operation Aboard Aircraft 1. 2. 3. 4. 5.

System Map: LCD Panel Open - Model A Design I 1 - 7

Quick Start Guide

System Map: LCD Panel Open - Model A Design II

Wireless Device Operation Aboard Aircraft

1 - 8 System Map: LCD Panel Open - Model A Design II

Quick Start Guide

System Map: LCD Panel Open - Model B

Wireless Device Operation Aboard Aircraft

System Map: LCD Panel Open - Model B 1 - 9

Quick Start Guide

System Map: Model C - LCD Panel Open

Wireless Device Operation Aboard Aircraft

1 - 10 System Map: Model C - LCD Panel Open

Quick Start Guide

Table 1 - 3 - LED Status Indicators

Table 1 - 2 - LED Power Indicators

Quick Start Guide

Hot Key Buttons - Model A Design I Only

Toggle *Silent Mode (for power saving)

Table 1 - 4 - Hot Key Buttons - Model A Design I Only

1 - 12 Hot Key Buttons - Model A Design I Only

Quick Start Guide

Play/Pause Key Numerical Keypad

NumLk & ScrLk Keys 3.75G/HSPA Module Power Toggle Key

NumLk & ScrLk

Figure 1 - 6 - Keyboard - Model A