Multi Channel AV Receiver: Operating Instructions

4-287-973-11(2)
Multi Channel AV Receiver

Operating Instructions
2011 Sony Corporation
Printed in Malaysia
STR-DA5700ES
WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. This symbol is intended to alert the user to the presence of the Hot Surface that may be hot if it is touched during the normal operation. This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
For customers in the United States

Owners Record
The model and serial numbers are located on the rear of the unit. Record these numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Serial No. Model No.
Important Safety Instructions

1) 2) 3) 4) 5) 6) 7) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11)Only use attachments/accessories specified by the manufacturer. 12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or when unused for long periods of time.
2US
14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. To reduce the risk of electric shock, the speaker cord should be connected to the apparatus and the speakers in accordance with the following instructions. 1) Disconnect the AC power cord from the MAINS. 2) Strip 10 to 15 mm of the wire insulation of the speaker cord. 3) Connect the speaker cord to the apparatus and the speakers carefully so as not to touch the core of speaker cord by hand. Also disconnect the AC power cord from the MAINS before disconnecting the speaker cord from the apparatus and the speakers.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
The following FCC statement applies only to the version of this model manufactured for sale in the U.S.A. Other versions may not comply with FCC technical regulations. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
3US
About This Manual

The instructions in this manual are for model STR-DA5700ES (the receiver). Check your model number by looking at the lower right corner of the front panel. The instructions in this manual describe mostly the operation of the receiver with the supplied remote control. You can also use the buttons or knobs on the receiver if they have the same or similar names as those on the remote control.
The font type (Shin Go R) installed in this receiver is provided by MORISAWA & COMPANY LTD. These names are the trademarks of MORISAWA & COMPANY LTD., and the copyright of the font also belongs to MORISAWA & COMPANY LTD. iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. All other trademarks and registered trademarks are of their respective holders. In this manual, and marks are not specified.
On Copyrights
This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX, and the doubleD symbol are trademarks of Dolby Laboratories. ** Manufactured under license under U.S. Patent Nos: 5,956,674, 5,974,380, 5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723, 7,392,195, 7,333,929, 7,548,853 & other U.S. and worldwide patents issued and pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes software. DTS, Inc. All Rights Reserved. This receiver incorporates High-Definition Multimedia Interface (HDMI) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Hardware and subscription sold separately. SiriusXM service automatically renews and you will be billed, at then-current rates, until you call us at 1866-635-2349 to cancel. See our Customer Agreement for complete terms at www.siriusxm.com. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved. Made for iPod, and Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. DLNA and DLNA CERTIFIED are trademarks and/ or service marks of the Digital Living Network Alliance. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. BRAVIA Sync is a trademark of Sony Corporation. x.v.Color and x.v.Color logo are trademarks of Sony Corporation. PlayStation is a registered trademark of Sony Computer Entertainment Inc. AVCHD and the AVCHD logo are trademarks of Panasonic Corporation and Sony Corporation.
4US
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft. Content owners use Microsoft PlayReady content access technology to protect their intellectual property, including copyrighted content. This device uses PlayReady technology to access PlayReadyprotected content and/or WMDRM-protected content. If the device fails to properly enforce restrictions on content usage, content owners may require Microsoft to revoke the devices ability to consume PlayReady-protected content. Revocation should not affect unprotected content or content protected by other content access technologies. Content owners may require you to upgrade PlayReady to access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade. WALKMAN and WALKMAN logo are registered trademarks of Sony Corporation. Android is a registered trademark or a trademark of Google Inc.
5US
Main features of the receiver

Compatible with a variety of connections and formats
Feature Multi-channel Description Page The receiver can output up to 9.1 channels. 24, 26 The receiver is equipped with speaker terminals for the front height channel. (Up to 7 channels can be output simultaneously with connected speakers.) 23
Compatible with various The receiver is compatible with various audio formats, such as standards Dolby TrueHD, DTS-HD Master Audio, DSD, multi-channel Linear PCM, FLAC, etc. HDMI
The receiver is equipped with five HDMI input jacks (of which two 28, 30, 32, HDMI IN 3 and IN 4 are the for AUDIO jacks which take sound 34 quality into account) on the back panel, and one HDMI jack on the front panel. You can connect various equipment using an HDMI connection. The receiver is compatible with various HDMI standards, such as 38, 88 Deep Color, x.v.Color, 3D transmission, Audio Return Channel (ARC), etc. You can operate the receiver and other equipment in conjunction 84 with each other using the Control for HDMI function.
Network
The receiver is equipped with four LAN ports that have switching 46 hub functions. The receiver is compatible with Internet video streaming. 57
The receiver allows you to play back content on a home network 61 via the DLNA-compliant home network function. USB You can easily play back iPhone/iPod content via the receiver using a USB connection. 56, 60
You can easily play back content on USB device/WALKMAN via 55 the receiver using a USB connection. Multi-zone You can enjoy music or video from other rooms. 78
Better image and sound quality

Feature Image up-conversion Description Page The receiver upscales or downscales analog video signals. The 22 signals can be upscaled to 1080p using an HDMI output jack. The receiver also upscales or downscales analog video signals for zone 2. The receiver is equipped with the D.C.A.C. (Digital Cinema Auto 101, 103 Calibration) function. Additionally, the receiver compensates sound output for each speaker and improves surround effects via the Speaker Relocation function and the A.P.M. (Automatic Phase Matching) function.
D.C.A.C.
6US
Feature Sound fields
Description
Page
The receiver creates optimum sound in accordance with various 72, 74 speaker connections or input sources. (The receivers preprogrammed sound fields are Dolby Pro Logic IIz, DTS Neo:X, HD-D.C.S., etc.)
High quality You can play back compressed audio files in high quality using the 107 reproduction of D.L.L. (Digital Legato Linear) function. compressed audio files H.A.T.S. The H.A.T.S. (High quality digital Audio Transmission System) 113 function transmits signals from a Super Audio CD player connected via an HDMI connection in high quality.
Useful functions
Feature Easy and accessible operations Description Page The receiver is equipped with a GUI (Graphical User Interface). 52 You can operate the receiver intuitively using a menu displayed on the TV screen. You can set the basic settings of the receiver easily using the Easy 49 Setup. A multifunction remote control for operating connected equipment 17 and the Multi-zone function, and a simple remote control performing normal operations are supplied with the receiver. You can recall various settings of the receiver all at one time with 91 the press of the EASY AUTOMATION button. Flexible functions The Sound Optimizer function optimizes audio output in accordance with the volume level. The Advanced Auto Volume function adjusts the volume to its optimum level automatically. 76 77
The A/V Sync function adjusts the time gap between audio output 108 and the visual display. The Pass Through function outputs HDMI signals to the TV even 87 when the receiver is in standby mode.
Others
Feature Environment-friendly function More useful Description Page The Auto Standby function switches the receiver to standby mode 118 automatically if you do not operate the receiver for a specific period of time or when there is no signal input to the receiver. You can operate the receiver using a smartphone equipped with ES Remote application software*.
* Compatible with iPhone/iPod touch and Android phone
91
7US
Table of Contents
Main features of the receiver ........................6 Description and location of parts ................10
Tuning
Listening to FM/AM radio ......................... 62 Listening to the satellite radio .................... 64 Connecting a satellite radio tuner .............. 65 Preparing to listen to the satellite radio ..... 65 Selecting a channel of the satellite radio ... 66 Presetting satellite radio channels .............. 67 Restricting access to specific channels (Parental Lock) ..................................... 68
Getting Started
Read the following before you connect any equipment ..............................................21 1: Installing speakers ..................................24 2: Connecting the monitor ..........................28 3: Connecting the video equipment ............30 4: Connecting the audio equipment ............39 5: Connecting to the network .....................45 6: Preparing the receiver and the remote control ....................................................47 7: Setting up the receiver using the Easy Setup ......................................................49 8: Setting up connected equipment .............51 9: Preparing a computer to use as a server .51 Guide to on-screen display operation .........52
Enjoying Sound Effects

Selecting the sound field ............................ 71 Using the Sound Optimizer function ......... 76 Adjusting the equalizer .............................. 77 Using the Advanced Auto Volume function ................................................. 77
Using Multi-zone Features Enjoying images/sound

Enjoying images/sound from the connected equipment ..............................................54 USB Device/WALKMAN ..........................55 iPhone/iPod .................................................56 DLNA .........................................................57 Internet video ..............................................57 FM/AM .......................................................59 SIRIUS .......................................................59 What you can do with the Multi-zone function ................................................. 78 Making a multi-zone connection ............... 78 Setting the speakers in zone 2 .................... 81 Switching the zone setting of the remote control ................................................... 81 Operating the receiver from another zone (ZONE 2/ZONE 3 operations) .............. 82
Using Other Features Enjoying an iPhone/iPod

Playing files on an iPhone/iPod ..................60 Using BRAVIA Sync features ................ 84 Switching the monitors that output the HDMI video signals ......................................... 86 Outputting the HDMI signals even when the receiver is in standby mode (Pass Through) ...................................... 87 Switching between digital and analog audio ...................................................... 88 Using other video/audio input jacks .......... 88
Playing via a Network

Playing files on a home network (DLNA) .................................................61
8US
Operating the receiver using a smartphone ......................................... 91 Saving various settings for the receiver and recalling those settings all at one time (Easy Automation) ................................ 91 Using the sleep timer .................................. 94 Recording using the receiver ...................... 94 Switching the command mode of the receiver and the remote control .......................... 95 Using a bi-amplifier connection ................. 97
Additional Information
Precautions ...............................................137 Troubleshooting ........................................138 Specifications ...........................................149 Index .........................................................153
Adjusting Settings
Using the setting menu ............................... 98 Easy Setup ................................................ 101 Speaker Settings ....................................... 101 Audio Settings .......................................... 107 Video Settings .......................................... 109 HDMI Settings ......................................... 112 Input Settings ........................................... 114 Network Settings ...................................... 115 Internet Services Settings ......................... 115 Zone Settings ............................................ 116 System Settings ........................................ 118 Network Update ....................................... 119 Operating without using the GUI ............. 119
Using the Remote Control

Operating each equipment using the remote control ................................................. 127 Turning off all connected equipment (SYSTEM STANDBY) ....................... 128 Programming the remote control ............. 128 Performing several commands in sequence automatically (Macro Play) ................. 132 Setting remote control codes that are not stored in the remote control ................ 133 Clearing the memory of the multifunction remote control ..................................... 135
9US
Description and location of parts

Front panel
To remove the cover

Press PUSH. When you remove the cover, keep it out of reach from children. A ?/1 ON/STANDBY Press to turn the receiver on or off. When the power is on, the lamp above the button lights up in green. If Control for HDMI (page 113), Pass Through (page 113), or Network Standby (page 115) is set to On, or the power for zone 2 or zone 3 is turned on, the lamp above the button lights up in amber when in the standby mode. B SPEAKERS (A/B/A+B/OFF) (page 50) C SOUND OPTIMIZER (page 76)
To open the cover

Slide the cover to the left.
D MEMORY/ENTER, TUNING MODE, TUNING (page 62) E Remote sensor Receives signals from remote control. F 2CH/A.DIRECT, A.F.D., MOVIE/ HD-D.C.S., MUSIC (page 71, 72, 72, 74) G Display window (page 12) H DIMMER Press repeatedly to adjust brightness of the display window. I DISPLAY MODE (page 126) J INPUT MODE (page 88)
10US
K HD-D.C.S. lamp, BERLIN PHILHARMONIC HALL lamp, TRUE CONCERT MAPPING lamp (page 72) L EASY AUTOMATION 1, 2 (page 91) M HDMI OUT (A/B/A+B/OFF) (page 86) N PHONES jack Connects to headphones. O TONE MODE, TONE Press TONE MODE repeatedly to select BASS or TREBLE, then turn TONE to adjust the bass/treble level of speakers. P AUTO CAL MIC jack (page 101) Connect the supplied optimizer microphone for Auto Calibration to the this jack. Q iPhone/iPod ( (USB) port and VIDEO IN jack) (page 55, 56, 60) R VIDEO 2 IN jacks (page 37) S MULTI CHANNEL DECODING lamp Lights up when multi-channel audio signals are decoded. T ZONE SELECT, POWER (page 78) Press SELECT repeatedly to select zone 2, zone 3 or main zone. Each time you press POWER, the output signals for the selected zone will be turned on or off. U INPUT SELECTOR Turn to select the input source to play back. To select the input source for zone 2 or zone 3, press ZONE SELECT (w;) to select zone 2 or zone 3 first (ZONE 2 [input name] or ZONE 3 [input name] appears on the display window), then turn INPUT SELECTOR to select the input source. V HDMI IN 6 (VIDEO 2) jack (page 38) W MASTER VOLUME (page 54)
11US
Indicators on the display
A SW Lights up when subwoofer(s) is (are) connected and the audio signal is output from the PRE OUT SUBWOOFER jack(s). B Playback channel indicator The letters (L, C, R, etc.) indicate the channels being decoded. Based on the speaker settings, the boxed letter(s) vary to show how the receiver downmixes or upmixes the source sound. L Front Left R Front Right C Center (monaural) LH Left High RH Right High SL Surround Left SR Surround Right S Surround (monaural or the surround equipment obtained by Pro Logic processing)
SBL Surround Back Left SBR Surround Back Right SB Surround Back (the surround back equipment obtained by 6.1 channel decoding) Example: Recording format: 5.1 Speaker pattern: 3/0.1 Sound Field: A.F.D. Auto
C INPUT indicator Lights up to indicate the current input. AUTO The INPUT MODE is set to AUTO. HDMI COAX OPT MULTI (MULTI CHANNEL INPUT) ARC (page 88) D HDMI OUT A + B (page 86) E SLEEP (page 94) F MEM Lights up when the preset memory function is activated.
12US
G ZONE 2/ZONE 3 (page 78) H L.F.E. Lights up when the disc being played back contains an L.F.E. (Low Frequency Effects) channel. The L.F.E. channel signal is actually being reproduced, the bars underneath the letters light up to indicate the level. Since the L.F.E. signal is not recorded in all parts of the input signal, the bar indication will fluctuate (and may turn off) during playback. I Speaker system indicator (page 50) J BI-AMP (page 97) K D.C.A.C. (page 101) Lights up when the measurement results of the Auto Calibration function are applied. L D.L.L. (page 107) M H.A.T.S. (page 113) N Tuning indicator Lights up when the receiver tunes to a radio station, or a satellite station. SIRIUS (page 64) ST Stereo reception MONO FM mode is set to the monaural mode. CAT The category mode is selected during the satellite radio operation. PRESET The tuning mode is set to the preset mode. O VOLUME Displays the current volume. P D.RANGE Lights up when dynamic range compression is activated. Q Dolby Digital Surround indicator Lights up with one of the respective indicators when the receiver is decoding the corresponding Dolby Digital format signals. ;D Dolby Digital
;D+ Dolby Digital Plus ;D EX Dolby Digital Surround EX R DTS-HD indicator Lights up when the receiver is decoding DTS-HD. DTS-HD Lights up constantly with the one of the following indicators. MSTR DTS-HD Master Audio HI RES DTS-HD High Resolution Audio S ;TrueHD Lights up when the receiver is decoding Dolby TrueHD. T Dolby Pro Logic indicator Lights up with one of the respective indicators when the receiver performs Dolby Pro Logic processing. This matrix surround decoding technology can enhance input signals. ;PL Dolby Pro Logic ;PLII Dolby Pro Logic II ;PLIIx Dolby Pro Logic IIx ;PLIIz Dolby Pro Logic IIz U A.P.M. (page 103) Lights up when the A.P.M. (Automatic Phase Matching) function is activated. V EQ Lights up when the equalizer is activated. W L-PCM Lights up when Linear PCM (Pulse Code Modulation) signals are input. X DSD Lights up when the receiver is receiving DSD (Direct Stream Digital) signals. Y DTS(-ES) indicator Lights up when DTS or DTS-ES signals are input.
continued
13US
DTS Lights up when the receiver is decoding DTS signals. DTS-ES Lights up with the either following indicator, depending on the input signal decoding format. 96/24 DTS 96/24 (96 kHz/24 bit) decoding DISC DTS-ES Discrete 6.1 MTX DTS-ES Matrix 6.1 Z NEO:X Lights up when DTS Neo:X Cinema/ Music/Game decoding is activated.
14US
Rear panel
A DIGITAL INPUT/OUTPUT section OPTICAL IN/OUT jacks (page 28, 32, 34, 42) COAXIAL IN jacks (page 31, 39) HDMI IN/OUT* jacks (page 28, 30, 32, 34) B RS232C port
C VIDEO/AUDIO INPUT/OUTPUT section (page 28, 31, 32, 34, 36) AUDIO IN/OUT jacks VIDEO IN/OUT* jacks AUDIO OUT jacks VIDEO OUT jack (page 78) ZONE 2 VIDEO OUT jack (page 80) An RJ-45 jack used to send a video signal to the equipment in zone 2. Use a CAT5 cable for the connection. Used for custom installation. For information on how to use this jack, consult your dealer. Attention
Do not use this jack for an Ethernet LAN connection. Doing so may cause a malfunction.
Used for maintenance and service.
continued
15US
D LAN ports (switching hubs) (page 46)
I SPEAKERS section (page 26)
E COMPONENT VIDEO INPUT/ OUTPUT section (page 28, 31, 34) Y, PB, PR IN/OUT* jacks
* You must connect the HDMI OUT or MONITOR OUT jack to your TV to watch the selected input image (page 28).
F ANTENNA section FM ANTENNA jack (page 43) AM ANTENNA jack (page 43) SIRIUS jack (page 65) G Control jacks for Sony equipment and other external equipment IR REMOTE IN/OUT jacks (page 78) Connect an IR repeater (not supplied) to use the Multi-zone function. TRIGGER OUT jacks (page 117) Connect to interlock on/off of the power supply of other 12V TRIGGER compliant equipment. H AUDIO INPUT/OUTPUT section AUDIO IN/OUT jacks (page 39, 42, 44) MULTI CHANNEL INPUT jacks (page 31, 39)
PRE OUT jacks Connect to an external power amplifier. 16US
Remote control
Use the supplied remote control to operate this receiver and other equipment. The remote control is pre-programmed to operate Sony video/audio equipment initially. Note
Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction.
Multifunction remote control (RM-AAL040)
Tip
When the receiver no longer responds to the remote control, replace all the batteries with new ones.
A ?/1 (on/standby) Press to turn the receiver on or off. B AV ?/1 (on/standby) Press to turn on or off the video/audio equipment that the remote is assigned to operate. C ZONE (page 78) D AMP Press to enable the receiver operation for main zone.
continued
17US
E TV INPUT Press TV (ws), then press TV INPUT to select the input signal of a TV. F GUIDE Press SHIFT (wd), then press GUIDE to display the on-screen program guide. G D.TUNING (page 62, 67) Press SHIFT (wd), then press to enter direct tuning mode. H ENT/MEM Press to enter the value or track using SHIFT (wd) and the numeric buttons (wg), or press ENT/MEM, then press the numeric buttons (wf) to select a preset number to which a station is stored during tuner operation. I SEN Press to go to the home page of the Sony Entertainment Network, a network service provided by Sony. J WATCH, LISTEN (page 54) K SOUND FIELD +/ (page 71, 72, 74, 72) L Color buttons Work according to the guide on the TV screen. M AMP MENU (page 119) N V/v/B/b Press V/v/B/b to select the menu items. Then press to enter the selection.
CATEGORY MODE Press to select the category mode for satellite tuner. TUNING +/ Press to select station. R PRESET + 2)/ Press to select preset stations. TV CH + 2)/ Press TV (ws), then press TV CH +/ to operate the TV, satellite tuner, etc. S EASY AUTOMATION 1, 2 (page 91) SLEEP (page 94) T RM SET UP (page 95) U FAVORITES (page 58) V TV Press to change the remote control button function to the one printed in yellow to enable the TV operation. W SHIFT Press to change the remote control button function to activate the buttons printed in pink. X Input buttons Press one of the buttons to select the equipment you want to use. When you press any of the input buttons, the receiver turns on. Y Numeric buttons Press SHIFT (wd), then press to input numbers. Press TV (ws), then press to select channel numbers of the TV. Z -/-Press SHIFT (wd), then press to select track numbers over 10 of the CD player, DVD player, Blu-ray Disc Player, or MD deck. select channel numbers over 10 of the TV, Satellite tuner or the VCR. wj NETFLIX Press to go to the home page of the Netflix service. Netflix unlimited membership required. wk SOUND OPTIMIZER (page 76)
O TOOLS/OPTIONS (page 52, 58, 64) Press to display and select items from option menus. P HOME (page 52) Press to display the home menu on the TV screen. Q m/M 1), x 1), X 1), N 1) 2), ./>1) Press to operate the DVD player, Blu-ray Disc Player, CD player, MD deck, tape deck, equipment connected to the (USB) port or to the network, or BRAVIA Internet Video, etc.
18US
wl HDMI OUTPUT (page 86) e; DISPLAY Press to display the control panel on the TV screen when playing back content via Internet video or a home network. ea RETURN/EXIT O Press to return to the previous menu or exit the menu. es CATEGORY +/ Press to select the category for satellite tuner. B/b Press to select an album. ed DISC SKIP Press to skip a disc when using a multidisc changer. ef MASTER VOL +/ (page 54) TV VOL After pressing TV (ws), you can also adjust and mute the volume level of the TV using these buttons. MUTING (page 54) eg MACRO 1, MACRO 2 (page 132) eh TOP MENU Opens or closes the BD-ROMs or DVDs Top Menu. AUDIO Press SHIFT (wd), then press AUDIO to select audio format/track. ej POP UP/MENU Opens or closes the BD-ROMs Pop-up Menu, or the DVDs menu. SUBTITLE Press SHIFT (wd), then press to select the subtitle language when multilingual subtitles are recorded on a BD-ROM/ DVD VIDEO.
1) See
Note
The above explanation is intended to serve as examples.
the table on page 127 for information on the buttons that you can use to control each equipment. 2) The tactile dot is attached to these buttons (5/TV, N, PRESET +/TV CH +). Use as a mark of operation.
continued
19US
Simple remote control (RM-AAU124)

This remote control can only be used to operate the receiver. You can control the main functions of the receiver with simple operations using this remote control.
H INPUT SELECTOR I MASTER VOLUME +/ (page 54) MUTING (page 54) J RETURN/EXIT O (page 52) K DISPLAY Press to display the control panel on the TV screen when playing back content via Internet video or a home network. L HDMI OUT (page 86)
A ?/1 (on/standby) Press to turn a receiver on or off. B 2CH/A.DIRECT, A.F.D., MOVIE, MUSIC (page 71, 72, 74) C AMP MENU (page 119) D V/v/B/b Press V/v/B/b to select the menu item. Then press to enter/confirm the selection.
E OPTIONS (page 52, 58, 64) F HOME (page 52) G N, x, ./> Press to operate the equipment connected to the front (USB) port or to the network, or Internet video, etc.
20US
Getting Started
Getting Started
Read the following before you connect any equipment

Before connecting cords, make sure to disconnect the AC power cord (mains lead).
Installing Speakers
See 1: Installing speakers (page 24).
v
Connecting the monitor and video equipment
The image quality depends on the connecting jack. See the illustration on the right. Select the connection according to the jacks on your equipment. The receiver has a video conversion function. For details, see Function for conversion of video signals (page 22).
Digital
Analog
High quality image
Q: Does your monitor have an HDMI jack?

t No: See the connection for a TV monitor without an HDMI jack in 2: Connecting the monitor (page 28) and 3: Connecting the video equipment (page 30). t Yes: See the connection for a TV monitor with an HDMI jack in 2: Connecting the monitor (page 28) and 3: Connecting the video equipment (page 30).
Connecting the audio equipment

See 4: Connecting the audio equipment (page 39).
v v v v
Preparing the receiver and the remote control

See 6: Preparing the receiver and the remote control (page 47).
Setting the receiver
See 7: Setting up the receiver using the Easy Setup (page 49).
Setting the audio output settings on the connected equipment

See 8: Setting up connected equipment (page 51).
For details on a multi-zone connection, see page 78. For details on a bi-amplifier connection, see page 97.
21US
Function for conversion of video signals

This receiver is equipped with a function for converting video signals. Composite video signals can be output as HDMI video and component video signals. Component video signals can be output as HDMI video and video signals. As the factory default setting, video signals input from the connected equipment are output to the HDMI OUT or MONITOR OUT jacks as shown in the table below. We recommend you set the video conversion function to match the resolution of the monitor you are using. For details on the video converting function, see Video Settings (page 109).
OUTPUT jack
HDMI OUT A/B (up to 1080p)

INPUT jack
COMPONENT VIDEO MONITOR MONITOR VIDEO OUT OUT (up to 1080i) a* a* a* a*
VIDEO 1 OUT
HDMI IN VIDEO IN COMPONENT VIDEO IN
a a a
a : Video signals are output. : Video signals are not output. * Video signals may not be output, depending on the setting in Resolution (page 109).
Note on converting video signals

Video signals for which the resolution has been converted may not be output from the COMPONENT VIDEO MONITOR OUT jacks or the HDMI OUT jacks simultaneously. If you connect equipment to both the COMPONENT VIDEO MONITOR OUT jacks and the HDMI OUT jacks, priority is given to the output from the HDMI OUT jacks.
To connect a recording equipment

When recording, connect the recording equipment to the VIDEO OUT jacks of the receiver. Connect cords for input and output signals to the same type of jack, as VIDEO OUT jacks do not have an up-conversion function. The HDMI OUT and the MONITOR OUT jacks cannot be used for recording.
To display Closed Caption

Set Resolution to Direct in the Video Settings menu when receiving a signal that supports Closed Captions. Use the same kind of cords for the input/output signals.
22US
Digital audio formats supported by the receiver

Getting Started Digital audio formats that this receiver can decode depend on digital audio input jacks of the equipment connected. This receiver supports the following audio formats.
Audio format Dolby Digital
5.1ch
Maximum number of channels
Connection between the playback equipment and the receiver COAXIAL/OPTICAL a HDMI a
Dolby Digital EX
6.1ch
Dolby Digital Plus*

7.1ch
Dolby TrueHD*
7.1ch
DTS
5.1ch
DTS-ES
6.1ch
DTS 96/24
5.1ch
DTS-HD High Resolution Audio*
7.1ch
DTS-HD Master Audio*
7.1ch
DSD*
5.1ch
a a
Multi-Channel Linear PCM*
7.1ch
* Audio signals are output in another format if the playback equipment does not correspond to the format. For details, refer to the operating instructions of the playback equipment.
23US
1: Installing speakers
This receiver allows you to use up to a 9.1 channel system (9 speakers and one subwoofer).
7.1 channel speaker system using surround back speakers

You can enjoy high fidelity reproduction of DVD or Blu-ray Disc software recorded sound in 6.1 channel or 7.1 channel format. A Front left speaker B Front right speaker C Center speaker D Surround left speaker E Surround right speaker F Surround back left speaker G Surround back right speaker J Subwoofer
Examples of speaker system configuration
7.1 channel speaker system using front high speakers

You can enjoy vertical sound effects (e.g., Pro Logic IIz mode, Neo:X mode). A Front left speaker B Front right speaker C Center speaker D Surround left speaker E Surround right speaker H Left high speaker I Right high speaker J Subwoofer
9.1 channel speaker system

You can enjoy high-quality multi-channel surround sound maximally just you would in an ideal dubbing theater. A Front left speaker B Front right speaker C Center speaker D Surround left speaker E Surround right speaker F Surround back left speaker G Surround back right speaker H Left high speaker I Right high speaker J Subwoofer

To fully enjoy theater-like multi-channel surround sound requires five speakers (two front speakers, a center speaker, and two surround speakers) and a subwoofer (5.1 channel system). A Front left speaker B Front right speaker C Center speaker D Surround left speaker E Surround right speaker J Subwoofer
24US
Recommended speaker placement

The angle A shown in the illustration should be the same.

Place the surround back speaker behind the seating position. Getting Started
Tip If you cannot place the speakers at the optimum angle, separate the surround speakers and the surround back speakers adequately and arrange them as symmetrically as possible. You can calibrate speaker positioning using Speaker Relocation even if you cannot place the speakers at the optimum angle (page 103). Arrange each pair of the surround speakers and the surround back speakers spread further back than 90 degrees to operate Speaker Relocation effectively. Install the front high speakers at a position as near as possible to the wall in front of the seating position and behind the speakers. The position should be at an angle of 25 to 30 degrees and at a height of 180 to 200 cm (190 cm is recommended). When you use a screen, arrange them slightly to the side of each end of the screen.
Since the subwoofer does not emit highly directional signals, you can place it wherever you want.
25US
Connecting speakers
Before connecting cords, make sure to disconnect the AC power cord (mains lead).
FRONT B/FRONT HIGH terminals 1)
A Monaural audio cord (not supplied) B Speaker cords (not supplied)

A Front speaker A (L) B Front speaker A (R) C Center speaker D Surround speaker (L) E Surround speaker (R) F Surround back speaker (L)2) 4) G Surround back speaker (R)2) 4) H Front high speaker (L)3) 4) I Front high speaker (R)3) 4) J Subwoofer5)
1)
If you have an additional front speaker system, connect them to the FRONT B/ FRONT HIGH terminals. You can select the front speaker system you are using with SPEAKERS on the front panel (page 10). 2) If you connect only one surround back speaker, connect it to the SURROUND BACK (ZONE 2) L terminals. 3) If you use front high speakers, connect them to the FRONT B/FRONT HIGH terminals. 4) You can connect both the surround back speakers and the front high speakers. However, sound cannot be output from the surround back speakers and the front high speakers simultaneously.
26US
You can set whether or not to output sound from the front high speakers using Sound Field Mode (page 75). However, Sound Field Mode may not work, depending on the sound field setting or input signals. 5) When you connect a subwoofer with an auto standby function, turn off the function when watching movies. If the auto standby function of the subwoofer is set to on, it goes into standby automatically based on the level of the input signal to the subwoofer, and the sound may not be output. You can connect two subwoofers to the receiver. The same signals are output from each of the PRE OUT SUBWOOFER jacks. Tip
You can loosen or tighten the SPEAKERS terminal easily using the supplied speaker cord connection tool.
Set Speaker Connection in the Speaker Settings menu (page 104) according to the speaker system you are using.
Getting Started
Loosen Tighten Speaker cord connection tool
Power amplifier
Tip
To enable 9.1 channel playback

The receiver can only output up to 7 channels simultaneously using the speaker terminals. You can output up to 9 channels simultaneously by connecting the PRE OUT SUR BACK jacks or the PRE OUT FRONT HIGH jacks to a power amplifier.
The same signal is output from both the SPEAKERS terminals and the PRE OUT jacks. For example, if you want to connect just the front speakers to another amplifier, connect that amplifier to the PRE OUT FRONT L and R jacks.
ZONE 2 connection
Only if you do not use surround back speakers and front high speakers, you can assign the SURROUND BACK (ZONE 2) terminals F and G to the speakers of the zone 2. Set the SURROUND BACK (ZONE 2) terminals to Zone 2 Speaker in Speaker Connection in the Speaker Settings menu (page 104). See Using Multi-zone Features (page 78) for details on connection and operation in zone 2.
27US
2: Connecting the monitor

You can watch the selected input image when you connect the HDMI OUT or MONITOR OUT jacks to a TV. You can operate this receiver using a GUI (Graphical User Interface).
TV monitor with an HDMI jack Audio signals If you connect the receiver to an Audio Return Channel (ARC)-compatible TVs HDMI jack via an HDMI cable, this connection is not necessary. Video signals If you connect the receiver to an Audio Return Channel (ARC)-compatible TV, connect it to an HDMI jack designated by ARC on the TV.
Audio signals or
Video signals or
TV monitor without an HDMI jack
It is not necessary to connect all the cords. Connect cords according to the jacks of your equipment.
28US
A Optical digital cord (not supplied) B Audio cord (not supplied) C Video cord (not supplied) D Component video cord (not supplied) E HDMI cable (not supplied)
We recommend that you use a Sony HDMI cable. TV type Audio Return Channel (ARC) Compatible* Incompatible Non-HDMI equipped Required cable (cord) Video E E D or C Audio A or B** A or B**
Getting Started
HDMI equipped
* You can output the TVs sound (multi-channel surround sound) from the receiver only by connecting the TV with an HDMI cable. ** If you want to output multi-channel surround sound from the receiver, use A for the audio connection
Notes
If you connect the TV to the receiver using video cord, set Playback Resolution to 480i/576i (page 111). When connecting optical digital cords, insert the plugs straight until they click into place. Do not bend or tie optical digital cords.
Tip
The sound of the TV is output from the speakers connected to the receiver if you connect the audio output jack of the TV and the TV IN jacks of the receiver. In this configuration, set the sound output jack of the TV to Fixed if it can be switched between either Fixed or Variable.
29US
3: Connecting the video equipment

Connections required for watching content recorded on a Blu-ray Disc or DVDs
To connect equipment with HDMI jacks
If your equipment does not have an HDMI jack, see page 31.
DVD player, Blu-ray Disc Player Video/audio signals
A
*
A HDMI cable (not supplied)

We recommend that you use a Sony HDMI cable. * You can connect any equipment with HDMI output jacks to the HDMI IN jacks of the receiver.
30US
To connect equipment with jacks other than HDMI jacks

It is not necessary to connect all the cords. Connect cords according to the jacks of your equipment. Getting Started
Blu-ray Disc Player, DVD player Audio signals or Video signals or
A Coaxial digital cord (not supplied) B Audio cord (not supplied) C Video cord (not supplied) D Component video cord (not supplied)
31US
Connections required for playing video games

PlayStation 3 (video game with an HDMI jack) Video/audio signals
Audio signals or
Video signals
Video game without an HDMI jack
32US
A HDMI cable (not supplied) B Optical digital cord (not supplied) C Audio cord (not supplied) D Video cord (not supplied)
Video game type Required cable (cord) Video HDMI equipped* Non-HDMI equipped A D Audio B or C**
Getting Started
* You can output the video games sound (multi-channel surround sound) from the receiver only by connecting the video game with an HDMI cable. ** If you want to output multi-channel surround sound from the receiver, use B for the audio connection
Notes
When connecting optical digital cords, insert the plugs straight until they click into place. Do not bend or tie optical digital cords.
33US
Connections required for watching programs via satellite broadcasting or via a cable TV
Satellite tuner, Cable box with an HDMI jack Video/audio signals
Audio signals or
Video signals or
Satellite tuner, Cable box without an HDMI jack
34US
A HDMI cable (not supplied) B Optical digital cord (not supplied) C Audio cord (not supplied) D Video cord (not supplied) E Component video (not supplied)
Satellite tuner/cable box type HDMI equipped* Non-HDMI equipped Required cable (cord) Video A E or D Audio B or C**
Getting Started
* You can output the satellite tuner/cable boxs sound (multi-channel surround sound) from the receiver only by connecting the satellite tuner/cable box with an HDMI cable. ** If you want to output multi-channel surround sound from the receiver, use B for the audio connection
Notes
35US
Connections required for watching content recorded on video tapes

VCR Audio signals Video signals
A Audio cord (not supplied) B Video cord (not supplied)
36US
Connections required for watching content via a camcorder

Getting Started
To the VIDEO 2 IN jacks
A
Video/audio signals Camcorder without an HDMI jack
Camcorder with an HDMI jack
A Video/audio cord (not supplied) B HDMI cable (not supplied)
37US
HDMI features
A digital audio signals transmitted by HDMI can be output from the speakers and the PRE OUT jacks on this receiver. This signal supports Dolby Digital, DTS, DSD, and Linear PCM. For details, see Digital audio formats supported by the receiver (page 23). Analog video signals input to the VIDEO jack, or COMPONENT VIDEO jacks can be output as HDMI signals. Audio signals are not output from the HDMI OUT jacks while the image is converted. This receiver supports High Bitrate Audio (DTS-HD Master Audio, Dolby TrueHD), Deep Color, x.v.Color and 3D transmission. The HDMI jacks of this receiver support the Control for HDMI function. The HDMI OUT B jack, however, does not support the Control for HDMI function. To enjoy 3D images, connect 3D-compatible TV and video equipment (Blu-ray Disc Player, Blu-ray Disc recorder, PlayStation 3, etc.) to the receiver using High Speed HDMI cables, put on 3D glasses, and then play back a 3D-compatible content.
Notes on connecting cables

Use a High Speed HDMI cable. If you use a Standard HDMI cable, 1080p, Deep Color, or 3D images may not be displayed properly. Sony recommends that you use an HDMIauthorized cable or Sony HDMI cable.
Note on using an HDMI-DVI conversion cable

We do not recommend using an HDMI-DVI conversion cable. When you connect an HDMI-DVI conversion cable to a DVI-D equipment, the sound and/or the image may be lost. Connect separate audio cords or digital connecting cords, then set Video Input Assign and Audio Input Assign in the Input Settings menu when the sound is not output correctly.
38US
4: Connecting the audio equipment

Getting Started
Connections required for listening content recorded on a Super Audio CD or ordinary CDs
If your Super Audio CD player is equipped with multi-channel output jacks, you can connect them to the MULTI CHANNEL INPUT jacks of this receiver to enjoy multi-channel sound. Alternatively, the MULTI CHANNEL INPUT jacks can be used to connect an external multichannel decoder.
continued
39US
CD player Super Audio CD player
or
or
or
B A Coaxial digital cord (not supplied) B Audio cord (not supplied) C Monaural audio cord (not supplied)
Note
Audio input signals from MULTI CHANNEL INPUT jacks cannot be recorded.
Tip
All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz sampling frequencies. The COAXIAL IN jacks are also compatible with 192 kHz sampling frequency.
40US
Note on playing a Super Audio CD on a Super Audio CD player

No sound is output when playing a Super Audio CD on a Super Audio CD player connected to only the COAXIAL SA-CD/CD IN jack on this receiver. When you play a Super Audio CD, connect the player to the MULTI CHANNEL INPUT or SA-CD/CD IN jacks, or connect a player which can output DSD signals from the HDMI jack to the receiver using an HDMI cable. Refer to the operating instructions supplied with the Super Audio CD player. Getting Started
If you want to connect several digital equipment, but cannot find an unused input
See Using other video/audio input jacks (page 88).
41US
Connections required for listening to content recorded on MDs

MD deck or
A Optical digital cord (not supplied) B Audio cord (not supplied)

Notes
Tip
All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz sampling frequencies.
42US
Connections required for listening to the radio

Getting Started
FM wire antenna (aerial) (supplied) AM loop antenna (aerial) (supplied)
Notes
To prevent noise pickup, keep the AM loop antenna (aerial) away from the receiver and other equipment. Be sure to fully extend the FM wire antenna (aerial). After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
43US
Connections required for listening to cassette tapes or records

Turntable Tape deck
A Audio cord (not supplied)

Note
If your turntable has a ground (earth) wire, connect it to the (U) SIGNAL GND terminal.
44US
5: Connecting to the network

If you have an Internet connection, you can connect this receiver to the Internet as well, through the wired LAN connection.
Getting Started
System requirements
The following system environment is required to use the network function of the receiver. A Broadband line connection A Broadband line connection to the Internet is required in order to enjoy Internet video or to use the software update function of the receiver. Modem This is the device that is connected to the broadband line to communicate with the Internet. Some of these devices are integrated with the router. Router Use a router compatible with 100 Mbps to enjoy content on your home network. We recommend that you use a router equipped with the built-in DHCP (Dynamic Host Configuration Protocol) server. This function automatically assigns IP addresses on the LAN. LAN cable (CAT5) We recommend that you use this type of cable for a wired LAN. Some flat-type LAN cables are easily affected by noise. We recommend that you use normal-type cables. If the receiver is used in an environment in which there is power supply noise from electric products or in a noisy network environment, use a shielded-type LAN cable.
45US
Configuration example
The following illustration is a configuration example of a home network with the receiver, a computer. We recommend that you use a wired connection.
Computer Internet Modem
Router LAN cable (not supplied) LAN cable (not supplied)
Note
Connect a router to one among ports 1 to 4 of the receiver using only one LAN cable. Do not connect the same router to the receiver using more than one LAN cable. It may cause a malfunction.
46US
6: Preparing the receiver and the remote control

Connecting the AC power cord (mains lead)
Connect the supplied AC power cord (mains lead) to the AC IN terminal on the receiver firmly, then connect the AC power cord (mains lead) to a wall outlet.
Make sure that the total power consumption of the equipment connected to the receivers AC OUTLET(s) does not exceed the wattage stated on the rear panel. Do not connect high-wattage electrical home appliances such as electric irons, fans, or TVs to this outlet. This may cause a malfunction.
Getting Started
Turning on the receiver

?/1
AC OUTLET
Press ?/1 to turn on the receiver.

AC IN terminal
To the wall outlet
You can also turn on the receiver using ?/1 on the remote control. When you turn off the receiver, press ?/1 again. STANDBY flashes on the display window. Do not disconnect the AC power cord (mains lead) while STANDBY is flashing. This may cause a malfunction.
AC power cord (mains lead) (supplied)
To save the power in standby mode

Set Control for HDMI (page 113), Pass Through (page 113), Network Standby (page 115) and RS232C Control (page 118) to Off, and turn off the power for zone 2/ zone 3. If Control for HDMI (page 113), Pass Through (page 113), or Network Standby (page 115) is set to On, or the power for zone 2 or zone 3 is turned on, the lamp above ?/1 lights up in amber. Note
The top of the receiver may become hot while the receiver is in standby mode. This condition occurs because current is flowing in the internal circuits of the receiver. This is not a malfunction.
A several space is left between the plug and the rear panel even when the power cord (mains lead) is inserted firmly. The cord is supposed be connected this way. This is not malfunction. Notes
The AC OUTLET(s) on the rear of the receiver is a switched outlet, which supplies power to the connected component only while the receiver is turned on. If the power for zone 2 or zone 3 is turned on, the AC OUTLET(s) supplies power to the connected component even when the receiver (main zone) is in standby mode.
47US
Performing initial setup operations (clearing all memorized settings)

Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to revert back to the factory default settings.
?/1 TONE MODE 2CH/A.DIRECT
Inserting batteries into the remote control

Insert two R6 (size-AA) batteries in the RM-AAL040 remote control, and the RM-AAU124 remote control. Observe the correct polarity when installing batteries.
RM-AAL040
RM-AAU124
Notes
1 2
Press ?/1 to turn off the receiver. While holding down the TONE MODE and 2CH/A.DIRECT, press ?/1 to turn on the receiver. Release the TONE MODE and 2CH/A.DIRECT after a few seconds.
The MEMORY CLEARING... appears on the display window for a while, then changes to MEMORY CLEARED! Changes or adjustments made to the settings are now reset to the defaults.
Do not leave the remote control in an extremely hot or humid place. Do not use a new battery with old ones. Do not mix manganese batteries and other kinds of batteries. If you do not intend to use the remote control for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. When you replace or remove the batteries, the programmed codes may be cleared. If this happens, program the remote control codes again (page 128, 132, 133).
Note
It takes about one minute for the memory to be cleared completely. Do not turn the receiver off until MEMORY CLEARED! appears on the display.
48US
Notes
7: Setting up the receiver using the Easy Setup

You can set the basic settings of the receiver easily by operating the receiver in accordance with the instructions on the TV screen. Switch the input of the TV to the input to which the receiver is connected. When you turn on the receiver for the first time, the EULA screen appears on the TV screen*. Agree to the EULA to proceed to the Easy Setup screen, then set up the receiver in accordance with the instructions on the Easy Setup screen. You can set up the following functions using the Easy Setup. Speaker Settings (Auto Calibration) Internet Settings
* If the EULA screen does not appear, display the EULA screen from EULA in the System Settings menu, then confirm and agree to the EULA.
Depending on the characteristics of the subwoofer you are using, the setup distance value may be different from the actual position. If you perform Speaker Settings (Auto Calibration) using the Easy Setup, the measurement results will be overwritten and saved on the currently selected position (Pos.1 is selected as the factory default setting).
Getting Started
Tip
Depending on the position of the subwoofer, the measurement results for polarity may vary. However, there will be no problems even if you continue to use the receiver with that value.
When you connect two subwoofers to the receiver

If you cannot obtain measurement results of the Auto Calibration function correctly, depending on the environment, or you want to make fine adjustments, you can setup the subwoofers manually. For details, see Speaker Setup in the Speaker Settings menu (page 104).
Notes on Speaker Settings (Auto Calibration)

Insert the plug of the optimizer microphone all the way inside the AUTO CAL MIC jack.
Notes on the speaker impedance

If you are not sure of the impedances of the speakers, refer to the operating instructions supplied with your speakers. (This information is often on the back of the speaker.) When you connect all speakers with a nominal impedance of 8 ohms or higher, set Speaker Impedance to 8 . When connecting other types of speakers, set it to 4 . When you connect front speakers to both the FRONT A and FRONT B/FRONT HIGH terminals, and you use the FRONT B/ FRONT HIGH terminals for the FRONT B speakers, connect the speakers with a nominal impedance of 8 ohms or higher. When you connect speakers with impedance of 16 ohms or higher in both A and B/FRONT HIGH configuration:
continued
Confirm active subwoofer setup

When a subwoofer is connected, turn on the subwoofer and turn up the volume prior to activating the subwoofer. Turn the LEVEL knob to just before the mid-point. If you connect a subwoofer with the crossover frequency function, set the value to maximum. If you connect a subwoofer with an auto standby function, set it to off (deactivated).
49US
Set Speaker Impedance to 8 in the Speaker Settings menu. For other types of speakers in other configurations: Set Speaker Impedance to 4 in the Speaker Settings menu.
To use the receiver as a preamplifier

You can use the Auto Calibration function when you use the receiver as a pre-amplifier. In this case, the distance value shown on the display may differ from the actual distance value. However, there will be no problems, even if you continue to use the receiver with that value.
To select the front speakers

You can select the front speakers you want to drive.
SPEAKERS (A/B/A+B/OFF)
To cancel the measurement process

The measurement process is cancelled by the following operations. Turning the power off Changing the volume Switching inputs Changing the setting of SPEAKERS (A/B/ A+B/OFF) Connecting headphones Operations other than the above are not allowed during the measurement process.
Press SPEAKERS (A/B/A+B/OFF) repeatedly to select the front speaker system you want to drive. You can confirm which set of terminals (A or B) are selected by checking the indicators in the display window.
Indicators Selected speakers The speakers connected to the FRONT A terminals. The speakers connected to the FRONT B/FRONT HIGH terminals. The speakers connected to both the FRONT A and FRONT B/FRONT HIGH terminals (parallel connection). SPEAKERS OFF appears in the display window. No audio signals are output from any speaker terminals, or the PRE OUT jacks.
To set up the receiver manually

See Adjusting Settings (page 98).
Note
If the speaker pattern is set so that there are front high speakers, you cannot select the FRONT B/ FRONT HIGH terminals.
50US
8: Setting up connected equipment

To output multi-channel digital audio, check the digital audio output setting on the connected equipment. For a Sony Blu-ray Disc Player, check that Audio (HDMI), DSD Output Mode, Dolby Digital, and DTS are set to Auto, On, Dolby Digital, and DTS, respectively (as of September 1, 2011). For a PlayStation 3, check that BD/DVD Audio Output Format (HDMI) and BD Audio Output Format (Optical Digital) are set to Bitstream (with system software version 3.70). For details, refer to the operating instructions supplied with the connected equipment.
9: Preparing a computer to use as a server

A server is a device which delivers content (music, photos, and videos) to a DLNA device on a home network. You can play back content stored on a computer on a home network with this receiver via that network after you have installed application software* which has a DLNA compliant server function.
* If you use a Windows 7-based computer, use Windows Media Player 12 bundled with Windows 7.
Getting Started
51US
Guide to on-screen display operation

You can display the menu of the receiver on the TV screen and select the function you want to use on the TV screen by pressing V/v/B/b and on the remote control.
Using the menu
1 2
Switch the input of the TV to the input to which the receiver is connected. Press HOME.
The home menu is displayed on the TV screen.
Press B/b repeatedly to select the menu you want, then press to enter the menu mode.
The menu item list appears on the TV screen.
V/v/B/b, RETURN/ EXIT O TOOLS/ OPTIONS HOME
Example: When you select Watch.
Tip
When z Option appears in the lower right portion of the screen, you can display the option menus by pressing TOOLS/OPTIONS and select a related function without reselecting the menu.
To return to the previous screen

Press RETURN/EXIT O.
To exit the menu

Press HOME to display the home menu, then press HOME again.
52US
Overview of the main menus

Menu Watch Description
Getting Started
Selects the video or photo source to be input to the receiver, or the video or photo content to be delivered via Internet video or a home network (page 54). Selects the music source to be input to the receiver, or the music content to be delivered via Internet video or a home network (page 54). Displays the Internet content added to the Favorites List. You can save up to 18 favorite Internet content items (page 58). Enables you to save various settings with the receiver and recalling the settings all at one time (page 91). Enables you to enjoy sound development provided by various Sony proprietary technologies or functions (page 71). You can adjust the settings of the receiver (page 98).
Listen
Favorites
Easy Automation
Sound Effects
Settings
53US
4
Enjoying images/sound
Press MASTER VOL +/ to adjust the volume.
Tips
Enjoying images/sound from the connected equipment
You can adjust the volume differently using the MASTER VOLUME knob on the receiver or the MASTER VOL +/ button on the remote control. To turn the volume up or down quickly Turn the MASTER VOLUME knob quickly. Press and hold the MASTER VOL +/ button. To make fine adjustment Turn the MASTER VOLUME knob slowly. Press the MASTER VOL +/ button and release it immediately.
To activate the muting function

Press MUTING on the remote control. To cancel, press MUTING on the remote control again or press MASTER VOL + to raise the volume. If you turn the receiver off while the sound is muted, the muting selection is cancelled.
To avoid damaging your speakers

V/v/B/b, TOOLS/ OPTIONS HOME
Before you turn off the receiver, be sure to turn down the volume level.
MASTER VOL
MUTING
Select Watch or Listen from the home menu, then press .

The menu item list appears on the TV screen.
2 3
54US
Select the equipment you want, then press . Turn on the equipment and start playback.
Notes
USB Device/WALKMAN
You can play video/music/photo files on the connected USB device. For playable types of files, see Playable types of files (page 151).
Connect the USB device to the (USB) port on the receiver.

Refer to the operating instructions of the USB device before connecting.
Do not remove the USB device during operation. To avoid data corruption or damage to the USB device, turn the receiver off when removing the USB device. If you connect a WALKMAN to the receiver, operate the WALKMAN using the remote control of the receiver the same way you do when you connect other USB devices to the receiver. You cannot use the controls on the WALKMAN.
USB device
2 3
Select Watch or Listen from the home menu, then press . Select My Video, My Music, or My Photo, then press .
Note
If no picture is output, change the setting for Playback Resolution (page 111).
Select USB Device, then press .

The folders and video/music/photo files are listed on the TV screen.
Press V/v/B/b and to select the file that you want to play.
The image or sound from the USB device is played on the receiver.
55US
4 iPhone/iPod
You can enjoy the music/video/photo and charge the battery of an iPhone/iPod via the receiver. For details on the compatible iPhone/iPod models with this function, see page 60. Note
You cannot use headphones during playback.
Select iPod (front), then press .

The video/music files are listed on the TV screen. If you select iPod (front) on My Photo, select a photo file using the controls on the iPhone/iPod (you do not need to proceed to step 5).
The image or sound from the iPhone/iPod is played back on the receiver. You can operate the iPhone/iPod using the buttons on the remote control (page 60). For operation details of the iPhone/iPod, also refer to the operating instructions of the iPhone/iPod.
Connect the iPhone/iPod to the (USB) port on the receiver.
iPhone/iPod (not supplied)
Apple Composite AV Cable (not supplied)
2 3
Note
56US
DLNA
You can play video/music/photo files on other DLNA-certified devices by connecting them to your home network.
Internet video
You can play back a variety of Internet content using the receiver.
1 2
1 2 3
Note
Connect the receiver to a network (page 45). Select Watch or Listen from the home menu, then press . Select Internet Video, Internet Music or Internet Photo, then press .
The Internet content screen appears. Note
Select the DLNA server icon, then press .

The folders and video/music/photo files are listed on the TV screen.
The image or sound from the DLNA server is played back on the receiver.
Select an Internet content provider icon, then press
If the Internet content list has not been retrieved, it will be represented by an unacquired icon or a new icon. Note
The Internet content is subject to being suspended or changed without notice.
To use the control panel

The control panel appears when the video file starts playing. The displayed items may differ, depending on Internet content providers. To display again, press DISPLAY.
A Control display Press V/v/B/b or operations.
for playback
continued
57US
B Playing status bar Status bar, cursor indicating the current position, playing time, duration of the video file C Network condition indicator D Network transmission speed E The next video file name F The currently selected video file name
Available options
Item Favorites List Add to Favorites Remove from Favorites IP Content Noise Reduction Details Displays the Favorites List. Adds Internet content to the Favorites List. Removes Internet content from the Favorites List. Adjusts the picture quality of Internet video content.
Registering your favorite content

You can register your favorite Internet content in Favorites List.
1 2
Display the Internet content screen. Select an Internet content provider icon you want to register in Favorites List, then press TOOLS/OPTIONS. Select Add to Favorites, then press .
To remove content from Favorites List 1 Press FAVORITES.

The Favorites List appears.
2 Select an Internet content provider icon

you want to remove from Favorites List, then press TOOLS/OPTIONS.
3 Select Remove from Favorites, then

press .
58US
FM/AM
You can listen to FM and AM broadcasts through the built-in tuner. Before operation, make sure you have connected the FM and AM antennas (aerials) to the receiver (page 43).
SIRIUS
You can listen to the satellite radio. Before operation, make sure you have connected a satellite radio tuner to the receiver and prepare to listen to the satellite radio (page 65, 65).
1 2
1 2
.
Select Listen from the home menu, then press . Select FM/AM, then press
Select Listen from the home menu, then press . Select SIRIUS, then press .
SIRIUS screen FM/AM screen

You can select and operate each item on the screen by pressing V/v/B/b and . You can select and operate each item on the screen by pressing V/v/B/b and .
A Preset number (page 67) A Band switch (page 62) B Frequency indication (page 62) C Preset station list (page 63) D Preset station name (page 63) B Channel number (page 66) C Channel name (page 66) D Category name (page 66) E Information Indicates various information, such as artist, song title, etc.
59US
For My Photo
Enjoying an iPhone/iPod
Press N, X
Operation Starts/pauses play. Pauses play. Fast reverses or forwards. Goes to the previous/next file. Turns the backlight on (or extends it for 30 seconds). Returns to previous display/folder hierarchy on iPhone/iPod. Returns to previous screen of the receivers GUI. Selects the previous/next item.
Playing files on an iPhone/iPod

Compatible iPhone/iPod models
The compatible iPhone/iPod models are as follows. Update your iPhone/iPod with the latest software before using with the receiver. Compatible models are as follows: iPod touch iPod touch 4th generation/iPod touch 3rd generation/iPod touch 2nd generation/iPod touch 1st generation iPod nano iPod nano 6th generation/iPod nano 5th generation (video camera)/iPod nano 4th generation (video)/iPod nano 3rd generation (video)/iPod nano 2nd generation (aluminum)/iPod nano 1st generation iPod iPod 5th generation (video)/iPod classic iPhone iPhone 4/iPhone 3GS/iPhone 3G/iPhone
x m or M . or > DISPLAY TOOLS/ OPTIONS RETURN/ EXIT O, B V/v ,b
Enters the selected item.
Notes
You cannot transfer songs onto the iPhone/iPod from this receiver. Sony cannot accept responsibility in the event that data recorded to iPhone/iPod is lost or damaged when using an iPhone/iPod connected to this receiver. This product has been designed specifically to work with iPhone/iPod and has been certified to meet Apple performance standards. Do not remove the iPhone/iPod during operation. To avoid data corruption or damage to the iPhone/ iPod, turn the receiver off when connecting or removing the iPhone/iPod. When you connect an iPod that is not compatible with the video output function and select iPod (front) in My Video or My Photo, an alert message appears on the TV screen.
To operate the iPhone/iPod using the remote control

You can operate the iPhone/iPod using the buttons on the remote control. The following table shows an example of buttons that can be used. (Depending on the iPhone/iPod model, the operation may be different.)
Tips
The iPhone/iPod is charged when connected to the receiver while the receiver is turned on. The receiver can recognize up to 3,000 files (including folders).
For My Video/My Music

Press N X x m or M . or > Operation Starts play. Pauses play. Stops play. Fast reverses or forwards. Goes to the previous/next file or chapter (if any).
60US
Playing via a Network
Playing files on a home network (DLNA)

This receiver can be used as a player and renderer. Server: Stores and sends files. Player: Receives and plays files from the server. Renderer: Receives and plays files from the server, and can be operated by another device (controller). Controller: Operates the renderer component.
Preparations for using the DLNA function

Connect the receiver to your home network (page 45). Prepare other DLNA-certified equipment. For details, refer to the operating instructions of the equipment. Playing via a Network
To play remote files by operating the receiver (Renderer) via a DLNA controller
You can operate the receiver with a DLNA-certified controller, such as Windows Media Player 12, when playing files stored on a DLNA server.
Computer (server, controller)
This receiver (renderer)
Control this receiver using a DLNA controller. For details of operation, see the operating instructions of the DLNA controller.
Note
Do not operate the receiver with the supplied remote and a DLNA controller at the same time.
Tip
The receiver is compatible with the Play To function of Windows Media Player 12 that comes standard with Windows 7.
61US
Tuning
Tuning to a station automatically (Auto Tuning)
Listening to FM/AM radio
1 2
Select the frequency indication on the FM/AM screen. Press V/v.

V scans from lower to higher frequency stations and v for scanning higher to lower. The receiver stops scanning whenever a station is received.
SHIFT
Numeric buttons D.TUNING
In case of poor FM stereo reception 1 Tune in the station you want to listen to
using Auto Tuning, Direct Tuning (page 62), or select the preset station you want (page 63).
2 Press TOOLS/OPTIONS.
The option menu appears.
3 Select STEREO/MONO, then press

.
4 Select MONO, then press
Toggling between FM and AM radio
Tuning into a station directly (Direct Tuning)

Enter the frequency of a station directly by using the numeric buttons on the remote control.
1 2 3 4
Select Listen from the home menu, then press . Select FM/AM, then press
The FM/AM screen appears.
1 2
Select the band switch. Press V/v to select FM or AM, then press .
Press SHIFT, then press D.TUNING on the FM/AM screen. Press the numeric buttons to enter the frequency, then press .
Example 1: FM 102.50 MHz Select 1 b 0 b 2 b 5 Example 2: AM 1,350 kHz Select 1 b 3 b 5 b 0
62US
Tips
Adjust the direction of the AM loop antenna (aerial) for optimum reception upon tuning to an AM station. The tuning scale for direct tuning is shown below. FM band 100 kHz AM band 10 kHz* * The AM tuning scale can be changed (page 64).
Repeat steps 1 to 4 to program another station.

You can store stations as follows: FM band: FM1 to FM30 AM band: AM1 to AM30
Tuning to preset stations
If you cannot tune to a station

. MHz or kHz appears and then the display returns to the current frequency. Make sure you have entered the right frequency. If not, repeat step 2. If you still cannot tune to a station, the frequency may not be in use in your area.
1 2 3
Select Listen from the home menu, then press . Select FM/AM, then press Select the preset number from the list, then press .
Preset numbers from 1 to 30 are available. Tuning
Programming FM/AM radio stations

You can program up to 30 FM and 30 AM stations as your favorite stations as preset stations.
To name preset stations (Name Input) 1 Select the preset number on which you
want to name.
Tune to the station that you want to program using Auto Tuning (page 62) or Direct Tuning (page 62).
In case of poor FM stereo reception, switch the FM reception mode (page 62).
3 Select Name Input, then press 4 Press V/v/B/b and
. The soft keyboard appears on the screen. to select a character one by one to enter the name.
2 3 4
Press TOOLS/OPTIONS.
5 Select Enter, then press
. The name you entered is registered.
Select Set Preset, then press . Select a preset number, then press .
The station is stored as the selected preset number.
To cancel naming input

Press RETURN/EXIT O or HOME.
63US
Changing the AM tuning scale

You can change the AM tuning scale to either 9 kHz or 10 kHz on the receiver. All preset stations will be erased when you change the tuning scale.
?/1 TUNING MODE
Listening to the satellite radio

To listen to satellite radio on your SiriusReady receiver, youll need to add a Sirius satellite radio tuner (sold separately). Sirius satellite radio service is available to residents of the United States (except Alaska and Hawaii), Puerto Rico (with coverage limitations) and Canada. Only SiriusXM brings you more of what you love, all in one place. Get over 130 channels, including an incredible variety of commercialfree music channels from Pop, Rock, Country, R&B, Hip-Hop and Jazz to Classical and much more. You also get the best professional and college sports, including play-by-play and expert sports talk and analysis, plus exclusive entertainment, talk, comedy, family programming and news from your most trusted sources. After you purchase a Sirius tuner, youll need to activate and subscribe to the service to listen to satellite radio. Easy-to-follow installation and set-up instructions are provided with the satellite tuners.
1 2 3
Press ?/1 to turn off the receiver. While holding down TUNING MODE, press ?/1 on the receiver. Change the current AM tuning scale to 9 kHz (or 10 kHz).
To reset the scale to 10 kHz (or 9 kHz), repeat the procedure above.
Available options
Item STEREO/MONO Set Preset Name Input Details Switches the FM reception mode to stereo or mono. Stores a radio station on a specific preset number. Names a preset station.
Packages for Sirius Tuners

Sirius Select Over 130 channels including a selection of premium programming like 2 channels of Howard Stern, every NFL game, every NASCAR race, Martha Stewart and more. Sirius Premier Over 140 channels including everything the Select package offers, plus additional premium programming like Oprah Radio, MLB Network Radio, NHL and NBA games, Opie & Anthony and more.
64US
Family friendly packages are also available to restrict channels that feature mature programming. To subscribe to a Sirius package, U.S. customers (including Puerto Rico) should visit www.siriusxm.com or call 1-888-539-7474. Canadian customers should visit www.sirius.ca. All programming packages may not be available in Canada.
Preparing to listen to the satellite radio
Connecting a satellite radio tuner

Tuning
Checking the ID number
1
SIRIUS jack
Select Listen from the home menu, then press . Select SIRIUS, then press Select All Categories, then press . Select the channel 0, then press . Check the Sirius ID on the TV screen and write it in the space provided here.
Sirius ID:_________________________ You can also check the Sirius ID using the display on the receiver. 65US
Connect the SiriusConnect Home tuner. When you use the SiriusConnect Home tuner with this receiver, be sure to connect the AC power adaptor supplied with the tuner to a wall outlet. Keep the SiriusConnect Home tuner, antenna, and AC power adaptor away from the speaker cords and the power cord to avoid picking up noise.
2 3 4 5
Checking receiving conditions (Antenna Aiming)
1 2 3 4 5
Select Listen from the home menu, then press . Select SIRIUS, then press Press TOOLS/OPTIONS.
Selecting a channel of the satellite radio

.
SHIFT
Select Antenna Aiming, then press .

The Antenna Aiming screen appears.
D.TUNING
While checking the quality of the reception, adjust the direction of the antenna to obtain the best reception.
V/v/B/b,
To exit the menu

Press RETURN/EXIT O or HOME.
HOME
Selecting a channel by category (Category Mode)

You can select a channel from one category or all the categories.
1 2 3
Select Listen from the home menu, then press . Select SIRIUS, then press .
Select the category, then press .

All Categories: You can select a channel from all the categories. (category name): You can select a channel from one category.
66US
Select the channel, then press .

The selected channel is being received. The channel information is displayed on the TV screen.
Selecting a channel by inputting the channel number directly (Direct Tuning)

Enter the channel number directly by using the numeric buttons on the remote control. This operation cannot be performed using the simple remote control.
1 2 3 4
Select Listen from the home menu, then press . Select SIRIUS, then press Press SHIFT, then press D.TUNING. Press the numeric buttons to enter the channel number, then press .
The selected channel is tune in.
Tuning
Select a channel you want to preset using Category Mode (page 66) or Direct Tuning (page 67). Press TOOLS/OPTIONS.
2 3
Presetting satellite radio channels

You can select the channels you want directly by presetting them using the preset numbers. You can preset up to 30 Sirius satellite radio channels.
Select Set Preset, then press .

The preset number selection screen appears.
Select the preset number you want to use as the preset channel, then press .
Preset channels from 1 to 30 are available, and a default channel is preset for all the preset channels when you purchase the receiver. The selected channel is registered as the preset channel you selected in step 1.
continued
67US
Repeat steps 1 to 4 to preset another channel.

You can store channels from 1 to 30.
SHIFT
Selecting preset channels
1 2 3 4
Select Listen from the home menu, then press . Select SIRIUS, then press Select Presets, then press . Select the preset number from the preset list, then press .
You can select stored preset channels from 1 to 30.
Numeric buttons
V/v/B/b, RETURN/ EXIT O
TOOLS/ OPTIONS
Note
The channel information you have preset may be changed if Sirius XM Radio Inc. change its channel programming.
Restricting access to specific channels

(Parental Lock)
You can restrict access to certain channels using your own lock code. When you select a channel using Category Mode, locked channels are skipped. The lock code is set to 0000 as the default. Change the lock code before you use this function for the first time. See To change the lock code (Lock Code) (page 69).
Select a channel you want to lock using Category Mode (page 66) or Direct Tuning (page 67). Press TOOLS/OPTIONS.
2 3 4 5 6
Select Parental Lock, then press . Select ON, then press .
Enter your 4-digit lock code. and the soft numerical keyboard appear.
Press V/v/B/b and to select your 4-digit lock code. Select ENTER, then press to enter the lock code.
The channel has been locked. appears and the Parental Lock is set.
68US
To delete the numbers you have entered, go back to step 2 by pressing RETURN/ EXIT O, and then repeat the procedure above from step 2.
3 Select Parental Lock, then press 4 Select OFF, then press
To change the lock code (Lock Code) 1 Select Listen from the home menu,
then press . .
. Enter your 4-digit lock code. and the soft numerical keyboard appear. to select your 4digit lock code.
5 Press V/v/B/b and
2 Select SIRIUS, then press 3 Press TOOLS/OPTIONS. 4 Select Lock Code, then press
6 Select ENTER, then press
. Enter your 4-digit lock code. and the soft numerical keyboard appear. to select your 4digit lock code.
to enter the lock code. The channel has been unlocked. appears and the channel is unlocked.
Notes
You cannot set individual lock codes for each channel. When the receiver is reset to the factory settings, the lock code returns to the default (0000), but the Parental Lock settings are not removed. You cannot preset locked channels. If you set the Parental Lock for a preset channel, the preset information for that channel returns to the default. You cannot set the Parental Lock for channel 0 or channel 184.
5 Press V/v/B/b and
Tuning
6 Select ENTER, then press
to enter the lock code. Enter a new lock code. and the soft numerical keyboard appear. digit lock code. To confirm, enter your new lock code again. appears.
7 Repeat steps 5 and 6 to enter a new 4-
8 Repeat steps 5 and 6 to reenter the

new lock code. The lock code has been changed. appears and the lock code is changed.
To listen to the locked channels 1 Select a locked channel you want to

listen to using Direct Tuning (page 67). Enter your 4-digit lock code. appears.
2 Press SHIFT, then enter your 4-digit

lock code using the numeric buttons. The channel is tuned in.
To cancel the Parental Lock 1 Select a channel you want to unlock

using Direct Tuning (page 67).
69US
Message list
Message appears Antenna Error Explanation Remedies
The antenna is not connected properly. Check the connection between the SiriusConnect Home tuner and the antenna. Try moving the antenna to another location. For details about the antenna location, refer to the instructions supplied with the SiriusConnect Home tuner.
Acquiring Signal The receiving condition is not good.
Call 888-539SIRI Check Sirius Tuner
You have not subscribed for the selected channel. The SiriusConnect Home tuner is not connected properly. Check all the connections, and then turn the system on again. Also make sure if the AC adaptor supplied with the SiriusConnect Home tuner is connected to a wall socket. The channel to be tuned in is void due to the change by the broadcast service, or the receiving condition is not good.
Invalid Channel
You have entered an invalid channel number. The selected channel is locked.
Locked Channel Subscription Updated Updating Channels xx % Completed ( xx are for integers) Firmware Updating Loading
The subscription information has been updated. Channel information is being updated.
The SiriusConnect Home tuner software is being updated. The display for the Sirius satellite radio feature is being prepared. There is no text information in the channel. This is not an error. The text information may not be displayed, depending on the system condition, for example, right after the system has received a channel.
70US
Selecting the sound field 1 Select Sound Effects, from the home menu, then press 2 Select Sound Field, then press . 3 Select the sound field you want.
Playing back with 2-channel sound
You can switch the output sound to 2-channel sound regardless of the recording formats of the software you are using, the playback equipment connected, or the sound field settings of the receiver.
2CH mode 2ch Stereo Effect The receiver outputs the sound from the front left/right speakers only. There is no sound from the subwoofer. Standard 2 channel stereo sources completely bypass the sound field processing and multi-channel surround formats are downmixed to 2 channels. You can switch the audio of the selected input to 2 channel analog input. This function enables you to enjoy high quality analog sources. When using this function, only the volume and front speaker level can be adjusted.
2ch Analog Direct
To listen to music through headphones connected to the receiver

Sound field Headphone (2ch) Effect This mode is selected automatically if you use headphones and when the mode other than 2ch Analog Direct is selected. Standard 2 channel stereo sources completely bypass the sound field processing and multi-channel surround formats are downmixed to 2 channels. Outputs the analog signals without processing by the tone, sound field, etc. This mode is selected automatically if you use headphones when MULTI IN is selected. Outputs the front analog signals from the MULTI CHANNEL INPUT jacks.
Headphone (Direct) Headphone (Multi)
71US
Playing back with multi-channel surround

The Auto Format Direct (A.F.D.) mode allows you to listen to higher fidelity sound and select the decoding mode for listening to a 2 channel stereo sound as multi-channel sound.
A.F.D. mode A.F.D. Auto Multi Stereo Effect Presets the sound as it was recorded/encoded without adding any surround effects. Outputs 2 channel left/right signals from all speakers.
Tip
We usually recommend A.F.D. Auto.
Enjoying a surround effect for movies

You can take advantage of surround sound simply by selecting one of the receivers preprogrammed sound fields. They bring the exciting and powerful sound of movie theaters into your home.
Sound field HD-D.C.S. Effect HD Digital Cinema Sound (HD-D.C.S.) is Sonys new innovative home theater technology using the latest acoustic and digital signal processing technologies. It is based on precise response measurement data of a mastering studio. With HD-D.C.S., you are able to enjoy Blu-ray and DVD movies at home with not only the high quality of sound, but also the best sound ambience, just as the movies sound engineer intended in the mastering process. You can select the effect type for HD-D.C.S. For details, see About the effect type for HD-D.C.S. (page 73). Performs Dolby Pro Logic II Movie mode decoding. This setting is ideal for movies encoded in Dolby Surround. In addition, this mode can reproduce sound in 5.1 channel for watching videos of overdubbed or old movies. Performs Dolby Pro Logic IIx Movie mode decoding. This setting expands Dolby Pro Logic II Movie or Dolby Digital 5.1 to discrete 7.1 movie channels. Performs Dolby Pro Logic IIz mode decoding. This setting can expand a source sound into up to 9.1 channels to which a vertical component is applied, and gives a dimension of presence and depth. PLIIz Height is the same sound field as that is described on page 74. You can adjust the gain level for PLIIz Height. For details, see About the gain level for PLIIz Height (page 75). Performs DTS Neo:X Cinema mode decoding. A source recorded in 2 to 7.1 channel format is enhanced up to 9.1 channels.
PLII Movie
PLIIx Movie PLIIz Height
Neo:X Cinema
72US
About the effect type for HDD.C.S.

HD-D.C.S. has three different types: Dynamic, Theater, and Studio. Each type has different reflection and reverberation sound mixture levels and is optimized to match a listeners room uniqueness, taste and mood.
x Dynamic
The Dynamic setting is suitable for an environment which is reverberant but lacks a spacious feeling (where sound absorption is not sufficient). This setting emphasizes the reflection of sound and reproduces the sound of a large, classical movie theater. Thus, the spacious feeling of a dubbing theater is emphasized and a unique acoustic field is created.
x Theater
Factory default setting. The Theater setting is suitable for a general living room. This setting reproduces the reverberation of sound just like in a movie theater (dubbing theater). It is most appropriate for watching content recorded on a Blu-ray Disc when you want the atmosphere of a movie theater. Enjoying Sound Effects
x Studio
The Studio setting is suitable for a living room with the appropriate sound equipment. This setting reproduces the reverberation of sound provided when a theatrical sound source is remixed for a Blu-ray Disc to a volume level suitable for home use. The level of reflection and reverberation of sound is kept to the minimum. However, dialogues and surround effects are reproduced vividly.
73US
Enjoying a surround effect for music

You can take advantage of surround sound simply by selecting one of the receivers preprogrammed sound fields. They bring the exciting and powerful sound of concert halls into your home.
Sound field Berlin Philharmonic Hall Effect Reproduces the sound characteristics of the Berlin Philharmonic Hall. Also works automatically in conjunction with reception of the The Berliner Philharmonikers Digital Concert Hall Internet service. Reproduces the sound characteristics of a concert hall in Amsterdam, Netherlands, which features a large sound stage produced by reflectivity. You can also adjust the effect level. For details, see About the effect level for True Concert Mapping A/B (page 75). Reproduces the sound characteristics of a concert hall in Vienna, Austria, which features resonant and unique reverberative sound. You can also adjust the effect level. For details, see About the effect level for True Concert Mapping A/B (page 75). Reproduces the acoustics of a jazz club. Reproduces the acoustics of a 300-seat live house. Reproduces the feeling of a large open-air stadium. Reproduces the feeling of sports broadcasting. Raises the sound image using the front high speakers. This setting is appropriate to watching music content on a large screen. Reproduces a clear enhanced sound image from your portable audio device. This mode is ideal for MP3 and other compressed music. Perform Dolby Pro Logic II Music mode decoding. This setting is ideal for normal stereo sources such as CDs. Performs Dolby Pro Logic IIx Music mode decoding. This setting is ideal for normal stereo sources such as CDs. Performs Dolby Pro Logic IIz mode decoding. This setting can expand a source sound into up to 9.1 channels to which a vertical component is applied, and gives a dimension of presence and depth. PLIIz Height is the same sound field as that is described on page 72. You can adjust the gain level for PLIIz Height. For details, see About the gain level for PLIIz Height (page 75). Performs DTS Neo:X Music mode decoding. A source recorded in 2 to 7.1 channel format is enhanced up to 9.1 channels. Performs DTS Neo:X Game mode decoding. A source recorded in 2 to 7.1 channel format is enhanced up to 9.1 channels.
True Concert Mapping A
True Concert Mapping B
Jazz Club Live Concert Stadium Sports Vocal Height Portable Audio PLII Music PLIIx Music PLIIz Height
Neo:X Music Neo:X Game
74US
About the effect level for True Concert Mapping A/B

You can set the reverberation level for the True Concert Mapping A/B sound field. This function is available when the speaker pattern is set so that there are front high speakers, and Sound Field Mode is set to Front High.
Stadium Sports Neo:X Cinema/Music/Game
x Front High
Outputs sound from the speakers, including the front high speakers (factory default setting). If you connect the surround back speakers and the front high speakers to the SURROUND BACK (ZONE 2) terminals and the FRONT B/FRONT HIGH terminals, respectively, sound is not output from the surround back speakers.
x Low
Turns down the reverberation volume level.
x Mid
Sets the reverberation volume level to the factory default.
x Standard x High
Turns up the reverberation volume level. Outputs sound from the speakers, except the front high speakers. Note
Depending on the setting or the audio format, sound may not be output from the front high speakers even if you set Sound Field Mode to Front High.
About the gain level for PLIIz Height

You can adjust the gain level of the front height channels for Pro Logic IIz mode (common for movie and music).
Notes on the sound fields

The sound fields do not work when MULTI IN is selected. You cannot select 2ch Analog Direct when you play back content via a USB device, a home network, or Internet video. Multi Stereo does not work when multichannel audio signals are being received. The sound fields for movie and music may not work, depending on the input or the speaker pattern you select, or with audio formats. The receiver may play back signals at a lower sampling frequency than the actual sampling frequency of the input signals, depending on the audio format. PLIIx Movie/Music, PLIIz Height, and Vocal Height do not appear, depending on the speaker pattern you select. Some speakers or the subwoofer may not output sound, depending on the sound field setting.
x Low
No gain will be applied.
x Mid
+3 dB will be applied (factory default setting).
x High
+5 dB will be applied.
Sound Field Mode

Lets you set whether or not to output sound from the front high speakers. This function is available when one of the following sound fields is selected, and the speaker pattern is set so that there are front high speakers. HD-D.C.S. Berlin Philharmonic Hall True Concert Mapping A/B Jazz Club Live Concert
continued
75US
If there is any noise present, the noise may be different, depending on the sound field you select. Neo:X (Cinema/Music/Game) does not work when signals with a sampling frequency of 32 kHz are being received.
Using the Sound Optimizer function

The Sound Optimizer function imparts a sense of presence and intensity of sound to playback of high volume sound, regardless of the volume level of the receiver. You can enjoy clear and dynamic sound even at a low volume, for examples, at night. The optimum effect to suit your environment is obtained by taking advantage of the Auto Calibration function.
1 2 3 4
Select Settings from the home menu, then press . Select Audio Settings, then press . Select Sound Optimizer, then press . Select On, then press .
The Sound Optimizer function is activated. You can also set the Sound Optimizer function On and Off using SOUND OPTIMIZER on the remote control and the receiver. Notes
This function does not work in the following cases. MULTI IN is selected. 2ch Analog Direct is being used. Headphones are being used. The receiver may play back signals at a lower sampling frequency than the actual sampling frequency of the input signals, depending on the audio format.
76US
1 Adjusting the equalizer

You can use following parameters to adjust the tonal quality (bass/treble level) of front, center, surround/surround back and front high speakers.
Bass Level (dB) Frequency (Hz) Treble
Select Settings from the home menu, then press . Select Audio Settings, then press . Select Advanced Auto Volume, then press . Select On, then press .
2 3 4
Notes
Be sure to reduce the volume level before you turn off this function. This function does not work in the following cases. MULTI IN is selected. 2ch Analog Direct is being used. The receiver may play back signals at a lower sampling frequency than the actual sampling frequency of the input signals, depending on the audio format.
1 2 3 4 5 6
Select Settings from the home menu, then press . Select Audio Settings, then press . Select Equalizer, then press . Select Front, Center, Sur/ SB, or Front High, then press . Select Bass or Treble. Adjust the gain, then press .
Note
This function does not work in the following cases. MULTI IN is selected. 2ch Analog Direct is being used.
Using the Advanced Auto Volume function

You can adjust the volume appropriate to each type of content automatically. This function is useful, for example, when the sound of a commercial is louder than the TV programs.
77US
Using Multi-zone Features
What you can do with the Multi-zone function

You can enjoy images and sounds from an equipment connected to the receiver in a zone other than the main zone. For example, you can watch the DVD in the main zone and listen to the CD in zone 2 or zone 3.
When using an IR repeater (not supplied), you can operate both an equipment in the main zone and Sony receiver in zone 2 or zone 3 from zone 2 or zone 3 using the remote control. Use an IR repeater when you install the receiver in a place where signals from the remote control cannot reach.
Making a multi-zone connection

Only signals from equipment connected to the analog input jacks are output through the ZONE 2 OUT/ZONE 3 OUT jacks. No signals are output from equipment connected to only the digital input jacks.
1:Zone 2 connections
1 Outputs sound from speakers in zone 2 using the SURROUND BACK (ZONE 2) terminals of the receiver.
Main zone
STR-DA5700ES
Zone 2
TV monitor
IR REMOTE IN
A B
ZONE 2 VIDEO OUT*
SURROUND BACK (ZONE 2)
Multifunction remote control
78US
2 Outputs sound from speakers in zone 2 using the receiver and another amplifier.
Main zone Zone 2
TV monitor
IR REMOTE IN STR-DA5700ES
C A
ZONE 2 VIDEO OUT*
ZONE 2 AUDIO OUT Multifunction remote control
A IR repeater (not supplied) B Speakers C Sony Amplifier/Receiver

* You can also connect to the ZONE 2 COMPONENT VIDEO OUT jack.
2:Zone 3 connections
Using Multi-zone Features Main zone Zone 3
IR REMOTE IN STR-DA5700ES
C A
ZONE 3 AUDIO OUT Multifunction remote control
A IR repeater (not supplied) B Speakers C Sony Amplifier/Receiver
79US
Making a zone 2 configuration using ZONE 2 VIDEO OUT (RJ-45 jack)

ZONE 2 VIDEO OUT (RJ-45 jack) is used only for custom installation by a qualified person. ZONE 2 VIDEO OUT (RJ-45 jack) is a jack that sends a source video signal to the component video input for zone 2. For details, consult your dealer. Attention
Do not use this jack for an Ethernet LAN connection. Doing so may cause a malfunction.
ZONE 2 VIDEO OUT (RJ-45 jack) connection

The RJ-45 pinouts use the T568B standard. Refer to the illustration below. Zone 2
Component Video Balun CAV-CVB1 TV monitor ZONE 2 VIDEO OUT (RJ-45 jack) CAT5 cable Component video cable
Note
CAV-CVB1 (Component Video Balun) must be used. Other types will cause trouble and may void your warranty.
CAT5 cable
Be sure to verify the CAT5 wiring connection is correct. Use Category 5e or Category 6 cable.
Pinout RJ-45 connector BLUE/Pb (R) BLUE/Pb (T) GREEN/Y (R) GND +11V GREEN/Y (T) RED/Pr (R) RED/Pr (T) BLUE/Pb (R) BLUE/Pb (T) GREEN/Y (R) GND +11V GREEN/Y (T) RED/Pr (R) RED/Pr (T) Wire color White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown Pin No. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
CAT5 cable
RJ-45 connector
80US
Setting the speakers in zone 2

When the speakers in zone 2 are connected to the SURROUND BACK (ZONE 2) terminals of the receiver (page 78), make the setting so that the sound selected in zone 2 is output from the speakers connected to the SURROUND BACK (ZONE 2) terminals. For details, see Speaker Connection in the Speaker Settings menu (page 104).
Parameter Fixed
Explanation The volume control is fixed to 0 dB. Recommended when using an equipment with the variable volume control.
Switching the zone setting of the remote control

The remote control is initially set to be used in zone 2. If you want to use it in zone 3, switch the zone setting of the remote control.
?/1 RM SET UP SHIFT AMP ZONE
Set the volume control for zone 2

You can set the volume control for the ZONE 2 AUDIO OUT jacks variable or fixed.
1 2 3 4 5
Select Settings from the home menu, then press . Select Zone Settings, then press . Select Zone Setup, then press . Select Line Out for Zone2, then press . Select the parameter you want, then press .
Parameter Variable Explanation The volume control is set to 40 dB initially. When you select this parameter, the volume for the ZONE 2 AUDIO OUT and the SURROUND BACK (ZONE 2) terminals can be changed in conjunction with each other. Recommended when using a power amplifier.
2, 3
Using Multi-zone Features
ENT/ MEM
1 2
Press ?/1 while pressing RM SET UP.

The AMP and ZONE buttons flash.
Press ZONE.
The AMP button goes off, the ZONE button keeps flashing and the SHIFT button lights up.
Press the numeric button 2 for the zone 2, or 3 for the zone 3 while the ZONE button is flashing.
The ZONE button lights up.
continued
81US
Press ENT/MEM.
The ZONE button flashes twice and the remote control switches to zone 2 or zone 3 mode.
Turn on the amplifier in zone 2 or zone 3.

In the case of illustration 1-1 (page 78), skip this step.
2 Operating the receiver from another zone

(ZONE 2/ZONE 3 operations)
The following operations are described for connecting an IR repeater and operating the receiver in zone 2 or zone 3. When an IR repeater is not connected, use this receiver in the main zone.
Press ZONE.
The remote control switches to zone 2 or zone 3. Change the zone setting of the remote control to zone 2 or zone 3 in advance (page 81).
3 4
Press ?/1.
The zone function is activated.
Press one of the input buttons on the remote control to select the source signals you want to output.
For zone 2, analog video and audio signals are output. For zone 3, only analog audio signals are output. When you select SOURCE, the signals of the current input in main zone are output.
ZONE
?/1
Input buttons
5
SOURCE
Adjust to a suitable volume.

In the case of illustration 1-1 (page 78), adjust the volume using MASTER VOL +/ on the remote control. In the case of illustration 1-2 (page 79) or 2 (page 79), adjust the volume using the receiver in zone 2 or zone 3. If you set Line Out for Zone2 to Variable, you can also adjust the volume in zone 2 using MASTER VOL +/ on the remote control (page 81).
To finish the zone 2/zone 3 operation

Press ZONE, then press ?/1.
MASTER VOL
Notes
When SOURCE is selected, the signals input to the MULTI CHANNEL INPUT jacks is not output from the ZONE 2 OUT or ZONE 3 OUT jacks even when MULTI IN is selected. TV, PHONO, or MULTI IN can be selected in the main zone only.
82US
Content via a USB device, iPhone/iPod, a home network, or Internet video is available in zone 2 and zone 3 only when SOURCE is selected. You can select either FM or AM from the main zone, zone 2, or zone 3. Priority is given to the choice which has most recently been selected, even if a different choice has already been selected in one of the zones. You can select only the same channel from SIRIUS when listening in both the main zone, zone 2, and zone 3 simultaneously. Priority is given to the channel which has most recently been selected, even if a different channel has already been selected in one of the zones.
Using Multi-zone Features 83US
Notes
Using Other Features
Using BRAVIA Sync features

What is BRAVIA Sync?
BRAVIA Sync is the name of a function on Sony products that enables compatible equipment connected via HDMI cables to be operated mutually using the BRAVIA remote control. This mutual operation is enabled by the Control for HDMI function using HDMI CEC (Consumer Electronics Control) standardized for HDMI (High-Definition Multimedia Interface). By connecting Sony equipment that are compatible with the BRAVIA Sync with an HDMI cable (not supplied), operation is simplified as below: System Power-Off (page 85) One-Touch Play (page 85) System Audio Control (page 85) Audio Return Channel (ARC) (page 86) Scene Select (page 86) Home Theater Control (page 86)
The following features may operate with non-Sony equipment. However, compatibility with all nonSony equipment is not guaranteed. System Power-Off One-Touch Play System Audio Control The following features are Sony proprietary functions. They can not operate with non-Sony equipment. Scene Select Home Theater Control Equipment not compatible with BRAVIA Sync can not activate these features.
Preparing for the BRAVIA Sync

To use the BRAVIA Sync, turn the Control for HDMI function on for both the receiver and the connected equipment. Turn the Control for HDMI function of the receiver and the connected equipment on individually.
1 2 3 4 5
Select Settings from the home menu, then press . Select HDMI Settings, then press . Select Control for HDMI, then press . Select On, then press .
The Control for HDMI function does not work in the following cases:
When you connect the receiver to an equipment which is not correspond with Sony Control for HDMI function. When you connect the receiver and equipment using other than HDMI connection. The Control for HDMI function does not work on an equipment connected to the HDMI OUT B jack of the receiver. We recommend that you connect the receiver to products featuring BRAVIA Sync.
The Control for HDMI function of the receiver is activated.
Turn the Control for HDMI function of the connected equipment on.
For details on setting the connected equipment, refer to its operating instructions.
84US
Repeat step 5 to set the Control for HDMI function and to display the image of all the playback equipment you want to use.
Start playback on the playback equipment.

Note
When you pull out the HDMI cable or change the connection, perform the steps above. However, you do not need to perform these steps when you use an HDMI IN 1, IN 2, or IN 6 jack.
To use the One-Touch Play function of the camcorder 1 Turn the Control for HDMI function on
for both the receiver and your camcorder.
2 Connect your camcorder to one of the

HDMI IN 1, IN 2, or IN 6 jacks (page 37). If you use a Sony camcorder, the TV is turned on in conjunction with the receiver, then the camcorder starts playback automatically. If you use a non-Sony camcorder, play back the camcorder continuously. Notes
Depending on the TV, the start of the content may not appear. Connect equipment such as a Sony camcorder equipped with the One-Touch Play function simply by making an HDMI connection to the HDMI IN 1, IN 2, or IN 6 jack. If you use other HDMI IN jacks, the receiver may not be switched to an appropriate input. In this case, manually select the input to which the camcorder is connected.
System Power-Off
When you turn the TV off, using the power button on the TVs remote control, the receiver and the connected equipment turn off automatically. You can also use the remote control to turn off the TV.
Press TV, then press AV ?/1.

The TV, receiver and connected equipment are turned off. Notes
Set the TV power supply interlock function to on before using the System Power-Off function. For details, refer to the operating instructions of the TV. Depending on the condition of the connected equipment, the connected equipment may not be turned off. For details, refer to the operating instructions of the connected equipment. If you use the System Power-Off function with a non-Sony TV, program the remote control according to the maker of the TV.
System Audio Control

You can enjoy the TV sound from the speakers connected to the receiver by a simple operation. You can also adjust the volume and turn off the sound of the receiver using the TVs remote control. You can use the System Audio Control function as follows. The sound of the TV is output from the speakers connected to the receiver when you turn the receiver on while the sound is being output from the TV speaker. If you turn off the receiver, the sound is output from the TV speaker. When you adjust the TV volume, the System Audio Control function adjusts the receivers volume simultaneously.
continued
One-Touch Play
When you play back content on the equipment connected to the receiver via an HDMI connection, the receiver is also turned on automatically and is switched to the appropriate HDMI input. When you set Pass Through to On, sound and image can be output only from the TV while the receiver remains in standby mode.
85US
You can also operate this function using the TV menu. For details, refer to the operating instructions of the TV. Notes
When Control for HDMI is set to On, the Audio Out settings in the HDMI Settings menu will set automatically based on the System Audio Control settings. If the TV is turned on before turning on the receiver, the TV will momentarily loose the sound output.
Home Theater Control

If a Home Theater Control-compatible TV is connected to the receiver, an icon for Internet based applications appears on the connected TV. You can switch an input of the receiver or switch sound fields by using your TVs remote control. You can also adjust the level of the center speaker or the subwoofer, or adjust the settings of Sound Optimizer (page 76), Dual Mono (page 107), or A/V Sync (page 108). To use the Home Theater Control function, your TV must be able to access a broadband service. For details, refer to the operating instructions supplied with your TV.
Audio Return Channel (ARC)

If the TV is compatible with the Audio Return Channel (ARC), an HDMI cable connection also sends a digital audio signal from the TV to the receiver. You do not need to make a separate audio connection for listening to TV sound from the receiver. For details, see Switching between digital and analog audio (page 88).
Scene Select
The optimum picture quality and sound field are selected automatically according to the scene selected on your TV. For details on the operation, refer to the operating instructions of the TV. Note
The sound field may not switch depending on the TV.
Switching the monitors that output the HDMI video signals

When you have two monitors connected to the HDMI OUT A and HDMI OUT B jacks, you can switch the output for these two monitors using the HDMI OUTPUT button on the remote control.
Correspondence table
Scene setting on the TV Cinema Sports Music Animation Photo Game Graphics Sound field HD-D.C.S. SPORTS Live Concert A.F.D. Auto A.F.D. Auto A.F.D. Auto A.F.D. Auto
HDMI OUTPUT
86US
1 2
Turn on the receiver and the two monitors. Press HDMI OUTPUT.
Each time you press the button, the output will be switched as follows: HDMI A t HDMI B t HDMI A + B t OFF t HDMI A You can also use the HDMI OUT button on the receiver.
3 4
Select Pass Through, then press .

Select the parameter you want, then press .

Parameter On Explanation When the receiver is in the standby mode, the receiver outputs HDMI signals from the receivers HDMI OUT A jack. The receiver does not output HDMI signals when in the standby mode. Turn on the receiver to enjoy the connected equipments source on the TV. This setting saves power in the standby mode, compared with the On setting.
Notes
If the compatible video format differs between the monitors connected to the HDMI OUT A jack and the HDMI OUT B jack of the receiver, HDMI A + B may not work. Depending on the playback equipment you connect, HDMI A + B may not work. Off
Outputting the HDMI signals even when the receiver is in standby mode
(Pass Through)
You can output the video and audio signals from the HDMI IN jack to the TV connected to the HDMI OUT A jack even when the receiver is in standby mode. If you use this function while Control for HDMI is set to On, the input of the receiver is switched in accordance with the operation of the connected equipment, even when the receiver is in standby mode. When you activate this function, make the settings for Pass Through following the steps below.
1 2
Select Settings from the home menu, then press . Select HDMI Settings, then press .
87US
Switching between digital and analog audio

When you connect equipment to both digital and analog audio input jacks on the receiver, you can fix the audio input mode to either of them, or switch from one to the other, depending on the type of material you intend to watch.
INPUT SELECTOR INPUT MODE
OPT Appears only when an optical jack is assigned to the input and selects the optical input jack automatically. COAX Appears only when a coaxial jack is assigned to the input and selects the coaxial input jack automatically. ANALOG Specifies the analog audio signals input to the AUDIO IN (L/R) jacks. Notes
Based on the input, ------ appears on the display window, and other modes cannot be selected. When 2ch Analog Direct is being used, or MULTI IN is selected, audio input is set to Analog. You cannot select other modes.
1 2
Select the input source using INPUT SELECTOR on the receiver. Press INPUT MODE on the receiver.
The selected audio input mode appears in the display window. AUTO Gives priority to digital audio signals when there are both digital and analog connections. If there are no digital audio signals, analog audio signals are selected. When TV input is selected, priority is given to the Audio Return Channel (ARC) signals. If your TV is not compatible with the Audio Return Channel (ARC), the digital optical audio signals are selected. If the Control for HDMI functions of both the receiver and the TV are not activated, the Audio Return Channel (ARC) does not work.
Using other video/audio input jacks

You can reassign video and/or audio signals to another input jacks. Example) Connect the OPTICAL OUT jack of the DVD player to the OPTICAL IN 1 jack of this receiver when you want to input the only digital optical audio signals from the DVD player. Connect the component video jack of the DVD player to the COMPONENT VIDEO IN 1 or COMPONENT VIDEO IN 2 jacks of this receiver when you want to input the video signals from the DVD player.
1 2 3
Select Settings from the home menu, then press . Select Input Settings, then press . Select Video Input Assign or Audio Input Assign, then press .
88US
Select the audio and/or video signals you want to assign to each input.
Notes
If you assign an input to any of the HDMI IN 1 to IN 6 jacks in Video Input Assign or Audio Input Assign, the same HDMI input jack is assigned to both the video input and audio input. If you want to assign an HDMI IN jack to either the video input or audio input, first assign an input to any of the HDMI IN 1 to IN 6 jacks in Video Input Assign or Audio Input Assign. Then, set the assignment of an HDMI IN jack to None in either Video Input Assign or Audio Input Assign, for whichever one you do not want to assign an HDMI IN jack to. When you operate the receiver without using the GUI, you can change the assignment of an HDMI IN jack using HDMI VIDEO ASSIGN ? or HDMI AUDIO ASSIGN ? in INPUT SETTINGS (page 124). If you change the assignment of an HDMI IN jack while the Control for HDMI function is being used, switch the input of the receiver to the input to which the HDMI equipment is connected. Otherwise the Control for HDMI function may not work properly. If you set the assignment of an HDMI IN jack to NONE in both Video Input Assign and Audio Input Assign, you can not select the input signals via the HDMI input. In this case, the Control for HDMI function works only on equipment other than the receiver. However, this is not malfunction.
continued
89US
Input name Assignable video Component1 input jacks (BD/DVD) Component2 (SAT/CATV) HDMI1 (GAME) HDMI2 (SAT/CATV) HDMI3 (SA-CD/CD) HDMI4 (BD/DVD) HDMI5 (VIDEO 1) HDMI6 (VIDEO 2) Assignable audio Optical1 input jacks (GAME) Optical2 (SAT/CATV) Optical3 (TV) Optical4 (MD) Coaxial1 (BD/DVD) Coaxial2 (VIDEO 1) Coaxial3 (SA-CD/CD) HDMI1 (GAME) HDMI2 (SAT/CATV) HDMI3 (SA-CD/CD) HDMI4 (BD/DVD) HDMI5 (VIDEO 1) HDMI6 (VIDEO 2)
BD/DVD GAME SAT/CATV VIDEO 1 VIDEO 2 a* a a a a a* a a a a a a a* a a a a a a* a a a a a* a a a a a a* a a a a a a a* a a a a a a a* a a* a a a a a a* a a a a a a a* a a a a a a a a a a a* a a a a a a a* a a a a a a* a a a a a a a a a* a a a a a a a a a a a a a*
TV a*
TAPE a a a a a a a a a a a a a a a a a a a a a
MD a a a a a a a a a a a a* a a a a a a a a a
SA-CD/CD PHONO MULTI IN a a a a a* a a a a a a a a a a* a a a* a a a a a a a a a a a
* factory default setting
90US
Notes
When you assign the digital audio input, the INPUT MODE setting may change automatically. When you assign a video input to the component or composite input, and an audio input to the HDMI input, component or composite video signals are not output from the HDMI OUT jacks. Component or composite video signals are output from the COMPONENT VIDEO MONITOR OUT jacks or the MONITOR VIDEO OUT jack. You cannot assign different HDMI jacks to separate video and audio input jacks of an input. You can assign multiple inputs with the same HDMI IN jack. However, if you use the One-Touch Play function on the equipment connected to the HDMI IN jack, the previous input, in its original input sequence, is preferentially selected.
Operating the receiver using a smartphone

You can operate the receiver using a smartphone equipped with the ES Remote application software. The ES Remote application software can be downloaded from the App Store (for iPhone) or the Android Market (for Android phone) for free.
Saving various settings for the receiver and recalling those settings all at one time
(Easy Automation)
You can save various settings with the receiver all at one time, and recall the settings and apply them to the receiver easily. For example, by saving the settings in the 1: Movie scene as follows, you can switch the settings of the receiver all at one time by a simple, one-touch operation without switching each setting for Input, Calibration Type, Sound Field, and HDMI Out, individually.
Setting item Input Calibration Type Sound Field HDMI Out Value set for 1: Movie BD/DVD Engineer HD-D.C.S. HDMI OUT B
continued
91US
The items for which you can save settings and the default values for each item are as follows.
Setting item Input Tuner Preset Sound Field Sleep Volume Default value 1: Movie 2: Music 3: Party 4: Night BD/DVD No Change HDD.C.S. No Change No Change SA-CD/ CD No Change No Change No Change No Change No Change No Change 30 min. 30 dB No Change No Change No Change No Change No Change No Change On No Change No Change No Change No Change No Change
Berlin Multi Philharmonic Stereo Hall No Change No Change No Change No Change No Change No Change No Change No Change No Change No Change No Change No Change No Change No Change Off 10 dB No Change No Change On No Change No Change No Change Off No Change No Change No Change No Change No Change
HDMI Out No Change Speaker No Change
Party Mode No Change A/V Sync No Change
Calibration No Type Change Digital Legato Linear EASY AUTOMATION Sound Optimizer No Change No Change
Sound No Field Mode Change Equalizer (Front) Equalizer (Center) No Change No Change
Equalizer No (Surround) Change Equalizer (Front High) No Change
* You can select Tuner Preset only when FM, AM, or SIRIUS is selected for Input.
92US
Recall the settings saved to the Scene
Tip
You can recall the setting(s) saved for 1: Movie or 2: Music directly by pressing EASY AUTOMATION 1 or EASY AUTOMATION 2 on the receiver or the remote control. You can also overwrite 1: Movie or 2: Music with the present settings by holding down EASY AUTOMATION 1 or EASY AUTOMATION 2 for 3 seconds in the same way as you do when you select Import Current Settings from the menu.
1 2
Select Easy Automation from the home menu, then press . Select a Scene you want, then press .
Save the settings to a Scene
1 2
Select Easy Automation from the home menu, then press . Select a Scene for which you want to save settings among from 1: Movie, 2: Music, 3: Party, or 4: Night, then press TOOLS/OPTIONS. Select the menu you want, then press .
Menu Explanation Edit Saved Scene Allows you to customize and save the settings to suit your preferences. Import Current Settings Loads the present settings of the receiver and saves those settings with the Scene. Input and Volume are set to No Change.
Notes
Settings items saved as No Change are not changed from the present settings even when you recall the Scene. Select Edit Saved Scene, then uncheck the box for a setting item on the edit screen to set No Change. When you recall the Scene, the settings that cannot be applied are ignored (e.g., the value for Sound Field when MULTI IN is selected, etc.).
93US
Using the sleep timer

You can set the receiver to turn off automatically at a specified time.
SHIFT
AMP
When sleep timer is being used, SLEEP lights up in the display window of the receiver. To check the remaining time before the receiver turns off, press SLEEP. The remaining time appears on the display window. If you press SLEEP again, the sleep timer is set to OFF.
Recording using the receiver

You can record from a video/audio equipment using the receiver. Refer to the operating instructions supplied with your recording equipment.
Recording with a video equipment
1 2 3
SLEEP
Select Watch from the home menu, then press . Select the playback equipment, then press . Prepare the equipment for playing.
For example, insert the video tape you want to copy into the VCR.
1 2
Press AMP.
The receiver can be operated using the remote control.
Prepare the recording equipment.

Insert a blank video tape, etc., into the recording equipment (VIDEO 1) for recording.
Press SHIFT, then press SLEEP.

Each time you press SLEEP, the display changes cyclically as follows:
Start recording on the recording equipment, then start the playback equipment.
94US
Recording with an audio equipment

You can record with an audio equipment using the receiver. Refer to the operating instructions supplied with your MD deck or tape deck.
1 2 3
Select Listen from the home menu, then press . Select the playback equipment, then press . Prepare the playback equipment for playing.
For example, insert a CD into the CD player.
The command modes of both the receiver and the remote control are those of the factory default setting (COMMAND MODE AV2). The receiver and the remote control, on the contrary, should use the same command mode. If the command modes of the receiver and the remote control are different, you cannot use the remote control to operate the receiver.
Switching the command mode of the receiver

?/1 2CH/A.DIRECT
Prepare the recording equipment.

Insert a blank MD or tape into the recording deck and adjust the recording volume level.
1 2
Press ?/1 to turn off the receiver. While holding down 2CH/ A.DIRECT, press ?/1 to turn on the receiver.
When the command mode is set to AV2, COMMAND MODE [AV2] appears on the display. When the command mode is set to AV1, COMMAND MODE [AV1] appears on the display.
Start recording on the recording deck, then start the playback equipment.
Switching the command mode of the receiver and the remote control
You can switch the command mode (COMMAND MODE AV1 or COMMAND MODE AV2) of the receiver and the remote control. Switch the command mode from the factory default setting to the appropriate setting, if other Sony equipment is operated accidentally by the same remote control, when you are operating the receiver using the remote control supplied with the receiver.
95US
Switching the command mode of the multifunction remote control

RM SET UP SHIFT ?/1
Switching the command mode of the simple remote control
AMP
DISPLAY
1, 2
ZONE
ENT/ MEM
MUTING
1 2
Press ?/1 while pressing RM SET UP.

The AMP and ZONE buttons flash.
Press MUTING and at the same time while pressing DISPLAY.
Press AMP.
The ZONE button goes off, the AMP button keeps flashing and the SHIFT button lights up.
Press the numeric button 1 or 2 while the AMP button is flashing.

When you press 1, the command mode is set to COMMAND MODE AV1. When you press 2, the command mode is set to COMMAND MODE AV2. The AMP button lights up.
Press ENT/MEM.
The AMP button flashes twice, then the command mode setting process is completed.
96US
Using a bi-amplifier connection

If you are not using surround back speakers and front high speakers, you can use the SURROUND BACK (ZONE 2) terminals for the front speakers for use with a bi-amplifier connection.
To connect speakers
Front speaker (R) Front speaker (L)
If you make the bi-amplifier settings, the speaker level, balance, and equalizer settings of the surround back speakers become invalid, and those of the front speakers are used. Signals output from the PRE OUT jacks are used with the same settings as those of the SPEAKERS terminals. If the speaker pattern is set so that there are surround back speakers or front high speakers, you cannot set the SURROUND BACK (ZONE 2) terminals for a bi-amplifier connection. When you operate the receiver without using the GUI, set SB ASSIGN to BI-AMP in SPEAKER SETTINGS (page 123).
Hi Lo
Hi Lo
Connect the jacks on the Lo (or Hi) side of the front speakers to the FRONT A terminals, and connect the jacks on the Hi (or Lo) side of the front speakers to the SURROUND BACK (ZONE 2) terminals. Make sure that metal fittings of Hi/Lo attached to the speakers have been removed from the speakers to avoid receiver malfunction.
To set up speakers
For details, see Speaker Connection in the Speaker Settings menu (page 104). Notes
You cannot use the FRONT B/FRONT HIGH terminals for a bi-amplifier connection. Make the bi-amplifier settings before you perform the Auto Calibration function.
97US
2
Adjusting Settings
Select the menu item you want, then press to access the menu item.
Example: When you select Audio Settings.
Using the setting menu

You can adjust the various settings for speakers, surround effects, multi-zone, etc., using the setting menu.
Select the parameter you want, then press to enter.
To return to the previous screen

To exit the menu

Press HOME.
V/v/B/b, RETURN/ EXIT O TOOLS/ OPTIONS HOME
Select Settings from the home menu, then press to enter the menu mode.
The setting menu list appears on the TV screen.
98US
Setting menu list

Settings Easy Setup (page 101) Speaker Settings (page 101) Auto Calibration Auto Calibration Setup Position Calibration Type User Reference Edit Front Reference Type Speaker Pair Match Name In Automatic Phase Matching Speaker Relocation Speaker Connection Speaker Setup Test Tone Center Analog Down Mix Speaker Impedance Distance Unit Audio Settings (page 107) Digital Legato Linear Sound Optimizer Equalizer Advanced Auto Volume Subwoofer Muting Dual Mono Dynamic Range Compressor (Input name) A/V Sync Decode Priority Sound Field Sound Field Mode Video Settings (page 109) Resolution Zone Resolution Playback Resolution 3D Output Settings TV Type Screen Format HDMI Settings (page 112) (Input name) Subwoofer Level Subwoofer Low Pass Filter Audio Out H.A.T.S. Control for HDMI Pass Through Video Direct continued
Adjusting Settings
99US
Input Settings (page 114) Network Settings (page 115)
Input Edit Audio Input Assign Video Input Assign Internet Settings Connection Server Settings Renderer Options Renderer Access Control External Control Network Standby
Internet Services Settings (page 115)
Parental Control Password Parental Control Area Code Internet Video Parental Control Internet Video Unrated Zone Control Zone Setup Language Auto Standby Settings Lock RS232C Control Software Update Notification Initialize Personal Information System Information EULA
Zone Settings (page 116) System Settings (page 118)
Network Update (page 119)
100US
Easy Setup
Re-runs the Easy Setup to make the basic settings. Follow the on-screen instructions (page 49).
Speaker Settings
You can set up your viewing environment (with the speaker system you are using) either automatically or manually. Adjusting Settings
Auto Calibration
Performs the D.C.A.C. (Digital Cinema Auto Calibration) function. This function allows you to perform automatic calibration, such as checking the connection between each speaker and the receiver, adjusting the speaker level, and measuring the distance of each speaker from your seating position automatically. Note
The measurement results will be overwritten and saved on the currently selected position.
Auto Calibration Setup

Lets you register three patterns for Position, depending on the seating positions, listening environment, and measurement conditions. You can also select a calibration type to compensate the each speaker.
Position
You can register more than one set of settings for the listening environment or recall a set of settings. Select the Position for which you want to register the measurement results on the Auto Calibration Setup screen. Pos.1 Pos.2 Pos.3
continued
101US
To set a compensation type for the speakers

You can select the compensation type to be used for the speakers for each Position.
Notes
This function works only when you select Front Reference for the Calibration Type (page 101). Perform Auto Calibration after you set Front Reference Type.
1 Select the Position for which you want

to set the speaker compensation type, then press .
To customize the frequency for the User Reference

You can customize the frequency for the User Reference in the Calibration Type based on the Full Flat compensation type.
2 Select the Calibration Type you want,

then press . Full Flat Makes the measurement of frequency from each speaker flat. Engineer Sets the frequency to match that of the Sony listening room standard. Front Reference Adjusts the characteristics of all the speakers to match the characteristics of the front speakers. User Reference Sets the frequency to one that you customized using User Reference Edit. Off Sets the Auto Calibration EQ to off. Note
You cannot set the Calibration Type for Position for which the measurement results have not been registered.
1 Select the User Reference Edit in the

Calibration Type menu, then press .
2 Adjust the frequency.

To set the pair match mode for the Auto Calibration EQ pattern

to set the pair match mode, then press .
2 Select Speaker Pair Match, then

press . All Calibrates all the speakers using the pair match processing of the left and right channels for each pair of speakers. Sur Calibrates the surround speakers and the surround back speakers using the pair match processing or the left and right channels for each pair of speakers. Off Calibrates each speaker individually. Notes
This function does not work when Auto Calibration is not performed. You cannot set SP Pair Matching to ALL when you select Front Reference for the Calibration Type (page 102).
To set the reference value when you select Front Reference for the Calibration Type
1 Select the Front Reference Type in

the Calibration Type menu, then press .
2 Select the parameter you want, then

press . L/R Sets the data of the left and right channels to the reference value. L Sets the data of the left channel to the reference value. R Sets the data of the right channel to the reference value. 102US
To name the Position

to name, then press .
2 Select Name In, then press
. The soft keyboard appears on the screen.
3 Press V/v/B/b and

character one by one.
to select a .
Drawing of the relocated speaker placement
4 Select Finish, then press
Automatic Phase Matching

Lets you set the A.P.M. (Automatic Phase Matching) function in the D.C.A.C. (Digital Cinema Auto Calibration) function (page 101). Calibrates the phase characteristics of the speakers and ensures a well-coordinated surround space. Adjusting Settings
x Off
Does not activate the A.P.M. function.
x Auto
Switches the A.P.M. function on or off automatically. Notes
This function does not work in the following cases. Off is selected for the calibration type (page 101). MULTI IN is selected. 2ch Analog Direct is being used. The receiver may play back signals at a lower sampling frequency than the actual sampling frequency of the input signals, depending on the audio format.
x Type B
Places four surround speakers at virtually identical angles, according to Recommendation ITU-R for 7.1 channel speaker placement.
Drawing of the relocated speaker placement
Speaker Relocation
Lets you calibrate speaker positioning (configuration angle of each speaker from the measurement position) to improve the surround effect.
x Type A
Places surround back speakers on the back wall in addition to those speakers in Recommendation ITU-R for 5.1 channel speaker placement.
x Off
Does not relocate speaker positioning. Note
This function does not work when you set Calibration Type (page 102) or Automatic Phase Matching (page 103) to Off.
103US
Speaker Connection
Lets you adjust each speaker manually. You can also adjust the speaker levels after the Easy Setup is completed. The Speaker Settings are only for the current Position. You can make the following settings using the wizard. Settings for the speaker pattern for the speaker system you are using Settings for the SURROUND BACK (ZONE 2) terminals for a bi-amplifier connection or a zone 2 connection (SB Assign) Settings that determine whether signals for the surround back channel are output to the SURROUND BACK (ZONE 2) terminals or the PRE OUT SUR BACK jacks Settings that determine whether signals for the front high channel are output to the FRONT B/FRONT HIGH speaker terminals or PRE OUT FRONT HIGH jacks Note
If the speaker pattern is set so that there are surround back speakers or front high speakers, you cannot set the SURROUND BACK (ZONE 2) terminals for a bi-amplifier connection or a zone 2 connection.
2 Select Level, then press
. You can adjust the level from 20 dB to +10 dB in 0.5 dB intervals. For the front left/right speakers, you can adjust the balance on either side. You can adjust the front left level from FL10.0 dB to FL+10.0 dB in 0.5 dB intervals. You can also adjust the front right level from FR10.0 dB to FR+10.0 dB in 0.5 dB intervals.
To adjust the distance from the seating position to each speaker

You can adjust the distance from the seating position to each speaker (front left/right, center, surround left/right, surround back left/ right, front high left/right, subwoofer.)
1 Select the speaker on the screen for

which you want to adjust the distance, then press .
2 Select a Distance, then press
. You can adjust the distance from 1.0 meter to 10.0 meters (3 feet 3 inches to 32 feet 9 inches) in 1 cm (1 inch) intervals.
To adjust the size of each speaker

You can adjust each speakers (front left/right, center, surround left/right, surround back left/ right, front high left/right) size.
Speaker Setup
Lets you adjust each speaker manually on the Manual Setup screen. You can also adjust the speaker levels after Auto Calibration is completed.

which you want to adjust the size, then press .
Select Level/Distance/Size, then press .
2 Select a Size, then press
To adjust the speaker level

You can adjust each speakers level (center, surround left/right, surround back left/right, front high left/right, subwoofer).
. Large If you connect large speakers that will effectively reproduce bass frequencies, select Large. Normally, select Large.

which you want to adjust the level, then press . 104US
Small If the sound is distorted, or you feel a lack of surround effects when using multichannel surround sound, select Small to activate the bass redirection circuitry and output the bass frequencies of each channel from the subwoofer or other Large speakers. Notes
The surround back speakers will be set to the same setting as that of the surround speakers. When the front speakers are set to Small, the center, surround, surround back, and front high speakers are also automatically set to Small. If you do not use the subwoofer, the front speakers are automatically set to Large.
You can adjust the level from 5 dB to +5 dB in 1 dB intervals.
Test Tone
Lets you select the test tone type on the Test Tone screen. Adjusting Settings
To output a test tone from each speaker

You can output a test tone from the speakers in sequence.
1 Select Test Tone, then press

The Test Tone screen appears.
2 Adjust the parameter, then press To adjust the crossover frequency of each speaker
Lets you set the bass crossover frequency of speakers that has been set to Small in the Size menu. Measured speaker crossover frequency is set for each speaker after Auto Calibration.
. Off Auto The test tone is output from each speaker in sequence. L, C, R, SR, SB*, SBR, SBL, SL, LH, RH, SW
* SB appears when only one surround back speaker is connected.
1 Select Crossover Frequency, then

press .
You can select which speakers will output the test tone.

which you want to adjust the crossover frequency.
3 Adjust Level, then press
3 Set the crossover frequency of the

selected speaker. Note
The surround back speakers will be set to the same setting as that of the surround speakers.
To output a test tone from adjacent speakers

You can output a test tone from adjacent speakers so that you can adjust the balance between the speakers.
1 Select Phase Noise, then press

The Phase Noise screen appears.
To adjust the level of the rear speakers

You can adjust the level of the rear speakers (surround speakers and surround back speaker(s)) in contrast to the level of the front speakers all at one time.
2 Adjust the parameter, then press
. Off L/R, L/C, C/R, R/SR, SR/SBR, SR/SB*, SBR/SBL, SR/SL, SB/SL*, SBL/SL, LH/RH, SL/L, L/SR, SL/R, L/RH, LH/R
*SR/SB and SB/SL appear when only one surround back speaker is connected.
1 Select All Surround Level, then press

.
2 Adjust the level of the rear speakers.

continued
105US
Lets you output the test tone sequentially from adjacent speakers. Some items may not be displayed, depending on the setting of the speaker pattern.
x On
We recommend you set Center Analog Down Mix to On to enjoy digital audio with high quality sound when you do not have a center speaker connected. Analog downmix works when you set Center Analog Down Mix to On. This setting is also effective to input signals from the MULTI CHANNEL INPUT jacks.
To output the source sound from adjacent speakers

You can output the source sound from adjacent speakers so that you can adjust the balance between the speakers.
Speaker Impedance
Lets you set the speaker impedance. For details, see 7: Setting up the receiver using the Easy Setup (page 49).
1 Select Phase Audio, then press

The Phase Audio screen appears.
2 Adjust the parameter, then press
. Off L/R, L/C, C/R, R/SR, SR/SBR, SR/SB*, SBR/SBL, SR/SL, SB/SL*, SBL/SL, LH/RH, SL/L, L/SR, SL/R, L/RH, LH/R
*SR/SB and SB/SL appear when only one surround back speaker is connected.
x4 x8
Distance Unit
Lets you select the unit of measurement for setting distances.
Lets you output front 2 channel source sound (instead of the test tone) sequentially from adjacent speakers. Some items may not be displayed, depending on the setting of the speaker pattern.
x meter
The distance is displayed in meters.
x feet
The distance is displayed in feet.
Center Analog Down Mix

Lets you set the analog downmix settings on or off.
x Off
If the speaker pattern is set so that there is a center speaker, this setting is set to Off automatically.
106US
Audio Settings
You can adjust settings for the audio to suit your preference.
Equalizer
Lets you adjust the bass and treble level for each speaker (page 77).
Digital Legato Linear (D.L.L.)

The D.L.L. function is Sony proprietary technology that allows low quality digital audio signals and analog audio signals to be played back with high quality sound.
Advanced Auto Volume

Lets you turn the Advanced Auto Volume function on or off (page 77).
Adjusting Settings
x Off x On
x Off x Auto 1
This function is available for lossy compression audio formats and analog audio signals.
Subwoofer Muting
Lets you prevent signals from being output via the PRE OUT SUBWOOFER jacks.
x Auto 2
This function is available for Linear PCM signals, as well as lossy compression audio formats and analog audio signals. Notes
This function may not work, depending on the content via a USB device, or a home network. This function works when A.F.D. Auto is selected. However, this function does not work in the following cases. Linear PCM signals with a sampling frequency of other than 44.1 kHz are being received. Dolby Digital Plus, Dolby Digital EX, Dolby TrueHD, DTS 96/24, DTS-ES Matrix 6.1, DTSHD Master Audio, or DTS-HD High Resolution Audio signals are being received.
x Off
The PRE OUT SUBWOOFER jacks output signals.
x On
The PRE OUT SUBWOOFER jacks do not output signals.
Dual Mono
Lets you select the language you want when you listen to the dual audio of a digital broadcast when available. This feature only functions for Dolby Digital sources.
x Main/Sub
Sound of the main language will be output through the front left speaker, and sound of the sub language will be output through the front right speaker simultaneously.
Sound Optimizer
Lets you turn the sound optimizer function on or off (page 76).
x Main x Off x On
Sound of the main language will be output.
x Sub
Sound of the sub language will be output.
107US
Dynamic Range Compressor

Lets you compress the dynamic range of the soundtrack. This may be useful when you want to watch movies at low volumes late at night. Dynamic range compression is possible with Dolby Digital sources only.
Decode Priority (Digital audio input decoding priority)

Lets you specify the input mode for the digital signal input to the DIGITAL IN jacks or HDMI IN jacks. You can set the function for each input independently.
x Off
The dynamic range is not compressed.
x PCM
When signals from the DIGITAL IN jack are selected, PCM signals are given priority (to prevent interruption when playback starts). However, when other signals are input, there may be no sound, depending on the format. In this case, set this item to Auto. When signals from the HDMI IN jack are selected, only PCM signals are output from the connected player. When signals in any other format are received, set this item to Auto.
x Auto
The dynamic range is compressed automatically.
x On
The dynamic range is compressed as intended by the recording engineer.
A/V Sync (Synchronizes audio and video output)

Lets you delay the output of audio to minimize the time gap between audio output and visual display. This function is useful when you use a large LCD or plasma monitor or a projector. You can set the function for each input independently.
x Auto
Automatically switches the input mode between Dolby Digital, DTS, or PCM. Note
Even when Decode Priority is set to PCM, the start of the sound may not be output due to signals on the CD being played back.
x HDMI Auto
The time gap between audio output and visual display for the monitor connected via an HDMI connection will be adjusted automatically based on the information for the TV. This feature is available only when the monitor supports the A/V Sync function.
Sound Field
Lets you select a sound effect applied to input signals. For details, see Enjoying Sound Effects (page 71). You can set the function for each input independently.
x 0 ms 1200 ms
You can adjust the delay from 0 ms to 1200 ms* in 10 ms intervals.
* The maximum delay may be limited to the lower value, depending on the audio stream.
Sound Field Mode

Lets you set whether or not to output sound from the front high speakers. For details, see Sound Field Mode (page 75).
Note
This function does not work in the following cases. MULTI IN is selected. 2ch Analog Direct is being used.
108US
Video Settings
You can adjust settings for video.
Resolution (Converting video signals)

Lets you convert the resolution of analog video input signals and output the converted signals.
Adjusting Settings
x Direct
Lets you output analog video input signals directly.
x 480p/576p x 720p x 1080i x 1080p

Output from Input from HDMI OUT jacks za) zb) zc) zc) z z z z z z z z z z zd) zd) a zb) z z a a a MONITOR MONITOR VIDEO COMPONENT OUT jack VIDEO OUT jacks a z
b)
x Auto x 480i/576i
Resolution menu setting Direct
COMPONENT VIDEO IN jacks VIDEO IN jacks
a zb)
Auto (factory default setting) 480i/576i
COMPONENT VIDEO IN jacks VIDEO IN jacks COMPONENT VIDEO IN jacks VIDEO IN jacks
480p/576p
720p, 1080i
1080p
z : Video signals are converted and output through the video converter. a : The same type of signal as that of the input signal is output. Video signals are not converted. : Video signals are not output.
a)
The resolution is set automatically, depending on the connected monitor.
b)
When the TV is connected to jacks other than the HDMI jacks, 480i/576i signals are output when Resolution is set to Auto. continued
109US
c)
480p/576p signals are output even if 480i/576i is set. d) Video signals without copyright protection are output based on the settings menu. Video signals with copyright protection are output as 480p/576p.
Notes
Video signals are not output from the COMPONENT VIDEO MONITOR OUT or MONITOR VIDEO OUT jacks when the monitor, etc., is connected to HDMI OUT jacks. If you select a resolution which the connected TV does not support in the Resolution menu, the images from the TV cannot be output correctly. Converted HDMI image output does not support x.v.Color, Deep Color and 3D.
Zone Resolution
Lets you convert the resolution of analog video input signal in zone 2.
x 480i/576i x 480p/576p
Zone Resolution menu setting 480i/576i (factory default setting) 480p/576p Output from Input from COMPONENT VIDEO IN jacks VIDEO IN jacks COMPONENT VIDEO IN jacks VIDEO IN jacks 720p, 1080i COMPONENT VIDEO IN jacks VIDEO IN jacks
x 720p x 1080i
ZONE 2 ZONE 2 VIDEO COMPONENT OUT jack VIDEO OUT jacks z z z z z* z* z z
z : Video signals are converted and output through the video converter. : Video signals are not output. * Video signals without copyright protection are output based on the settings menu. Video signals with copyright protection are output as 480p/576p.
110US
Playback Resolution
This function targets content via a USB device, a home network, and Internet video.
x 480i/576i x 480p/576p x 720p

Output HDMI OUT video jacks resolution Playback Resolution menu setting 480i/576i 480p/576p 480i/576i 480p/576p
x 1080i x 1080p
Adjusting Settings
MONITOR COMPONE NT VIDEO OUT jacks
MONITOR ZONE 2 VIDEO OUT COMPONE jack NT VIDEO OUT OUT jacks 480i/576i* 480i/576i* 480i/576i* 480p/576p* 720p* 1080i* 1080i*
ZONE 2 VIDEO OUT jack
480i/576i* 480p/576p* 720p* 1080i* 1080i*
480i/576i* 480i/576i*
720p (factory default setting) 720p 1080i 1080p 1080i 1080p
* If you play back content that is protected by Macrovision, the receiver may output the image at low resolution, or a warning message which informs that the video signals cannot be output may appear.
Notes
If the warning message Video cannot be output from this jack. appears, perform the following procedure. 1Select BD/DVD as the input for the main zone. 2Set Playback Resolution to 480i/576i or 480p/576p. If no picture is output when you play back content via a USB device, a home network, or Internet video from the Watch/Listen menu, perform the following procedure. 1Select BD/DVD as the input for the main zone. 2Set Playback Resolution to a lower resolution.
111US
3D Output Settings
HDMI Settings
You can adjust the required settings for equipment connected to the HDMI jacks.
x Auto
Select this to display 3D compatible content in 3D.
Subwoofer Level
Lets you set the level of the subwoofer to 0 dB or +10 dB when PCM signals are input via an HDMI connection. You can set the level for each input to which an HDMI input jack is assigned independently.
x Off
Select this to display all content in 2D.
TV Type
x 0 dB x Auto
Automatically sets the level to 0 dB or +10 dB, depending on the audio stream.
x 16:9
Select this when connecting to a wide-screen TV or a TV with a wide-mode function.
x +10 dB
x 4:3
Select this when connecting to a 4:3 screen TV without a wide-mode function.
Subwoofer Low Pass Filter

Lets you turn the low-pass filter for the subwoofer output on or off. The low-pass filter works when PCM signals are input via an HDMI connection. You can set the function for each input to which an HDMI input jack is assigned independently. Turn the function on if you connect a subwoofer without the crossover frequency function.
Screen Format
x Original
Select this when connecting to a TV with a wide-mode function. Displays a 4:3 screen picture in 16:9 aspect ratio even on a widescreen TV.
x Off
Does not activate the low-pass filter.
x Fixed Aspect Ratio

Changes the picture size to fit the screen size with the original picture aspect ratio.
x On
Always activates the low-pass filter with a cutoff frequency of 120 Hz.
Audio Out
Lets you set the HDMI audio signals output from the playback equipment connected to the receiver via an HDMI connection.
112US
x TV+AMP
The sound is output from the TV speaker and the speakers connected to the receiver. Notes
The sound quality of the playback equipment depends on the TVs sound quality, such as the number of channels, and the sampling frequency, etc. If the TV has stereo speakers, the sound output from the receiver is also in stereo as that of the TV, even if you play multi-channel source. When you connect the receiver to a video equipment (projector, etc.), sound may not be output from the receiver. In this case, select AMP. When you do not select an HDMI input jack as an audio input in Audio Input Assign in the Input Settings menu, sound is not output from the TV.
The H.A.T.S. function of this receiver works when a Sony SCD-XA5400ES is connected to the receiver. While the H.A.T.S. function is working, sound is not output from the front high speakers.
Stream information about the H.A.T.S. function available

Audio signal input Sampling frequency Linear PCM 2ch 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz 2.8224 MHz
Adjusting Settings
Linear PCM Multi
DSD
x AMP
The HDMI audio signals from the playback equipment is only output to speakers connected to the receiver. The multi-channel sound can be played back as it is. Note
When Control for HDMI is set to On, Audio Out may be changed automatically.
Control for HDMI

Lets you turn the function which controls equipment connected to the HDMI jack using an HDMI cable on or off.
x Off x On
H.A.T.S.
Lets you turn the H.A.T.S. (High quality digital Audio Transmission System) function on or off. When the H.A.T.S. function is turned on, the sound quality is enhanced because there is no jitter (timing gaps when reading signals) when transmitting digital audio signals.
Pass Through
Lets you output HDMI signals to the TV even when the receiver is in standby mode. For details, see Outputting the HDMI signals even when the receiver is in standby mode (Pass Through) (page 87).
x Off x On
x Off x On
Notes
It takes some time to output the sound after a playback operation is performed on the connected equipment (e.g., pressing the PLAY button, pressing the STOP button, pressing the PAUSE button) due to limitations of the H.A.T.S. system. The time lag depends on the sound source.
113US
Video Direct
Lets you output the video input signals from the HDMI IN jack directly to the HDMI OUT jack.
Note
You cannot select an input which is set to Hidden, or HIDDEN in INPUT SKIP ? in INPUT SETTINGS (page 124) without using the GUI, even if you use INPUT SELECTOR on the receiver.
x Off
The input signals from the HDMI IN jack are output through a video processor.
Audio Input Assign

Lets you set the audio input jack(s) assigned to each input. For details, see Using other video/audio input jacks (page 88).
x On
The input signals from the HDMI IN jack are output directly.
x HDMI
HDMI IN 1/2/3/4/5/6, none
Input Settings
You can adjust the settings for the connections of the receiver and other equipment.
x Digital
OPT IN 1/2/3/4, COAX IN 1/2, none
x Analog
Factory default setting
Input Edit
Lets you set the following items for each input.
Video Input Assign

Lets you set the video input jack(s) assigned to each input. For details, see Using other video/audio input jacks (page 88).
x Watch/Listen
Sets whether an input is displayed on the Watch menu or the Listen menu. Watch: Displays an input to the Watch menu. Listen: Displays an input to the Listen menu. Watch/Listen: Displays an input to both the Watch and Listen menus. Hidden: Does not display an input to both the Watch and Listen menus. When you select an input, you can skip an input which is set to Hidden.
x HDMI
HDMI IN 1/2/3/4/5/6, none
x Component
COMPONENT IN 1/2, none
x Analog
Factory default setting
x Icon
Sets the icon displayed on the Watch/Listen menu.
x Name
Sets the name displayed on the Watch/Listen menu.
114US
Network Settings
You can adjust the settings for the network.
Network Standby
Lets you turn the function that activates the switching hubs on the rear of the receiver and allows network controller, ES Remote, etc., to control the receiver on or off even when the receiver is in standby mode. In standby mode, the start-up time of the network function is reduced after the receiver is turned on.
Internet Settings
Lets you check or change the network settings. You can change the settings for the following items either manually or automatically. IP Address DNS Proxy Server Connect the receiver to the network beforehand. For details, see 5: Connecting to the network (page 45).
Adjusting Settings
x Off
The network function turns off when the receiver is in standby mode.
x On
The network function works even when the receiver is in standby mode.
Connection Server Settings

Lets you set whether or not to display the connected DLNA server.
Internet Services Settings

Parental Control Password
Lets you set or change the password for the parental control function. A password allows you to set a restriction on Internet video playback.
Renderer Options
x Renderer Name
Shows the renderer name of the receiver.
x Auto Access Permission

Sets whether or not to allow automatic access from newly detected DLNA controller.
Parental Control Area Code Renderer Access Control

Lets you set whether or not to accept commands from DLNA controllers. Playback of some Internet videos can be limited according to the geographic area. Scenes may be blocked or replaced with different scenes. Set the function in accordance with the onscreen instructions.
Code Area Argentina Australia Austria Belgium Brazil Code 2304 2333 2363 2362 2376 Area Korea Luxembourg Malaysia Mexico Netherlands continued
External Control
Let you turn the function which controls the receiver from ES Remote on the home network on or off.
2044 2047 2046
x Off x On
2057 2070
115US
Code 2090 2092 2093 2115 2165 2174 2109 2200 2219 2248 2238 2239 2254 2276
Area Chile China Colombia Denmark Finland France Germany Greece Hong Kong India Indonesia Ireland Italy Japan
Code 2390 2379 2427 2424 2428 2436 2489 2501 2149 2499 2086 2543 2528 2184
Area New Zealand Norway Pakistan Philippines Poland Portugal Russia Singapore Spain Sweden Switzerland Taiwan Thailand United Kingdom
Zone Settings
You can adjust settings for the main zone, zone 2 or zone 3.
Zone Control
To turn the power on or off for zone 2/zone 3
You can turn zone 2 or zone 3 operation on or off.
1 Select the zone you want to turn on or

off, then press On Off . .
2 Select On or Off, then press
Internet Video Parental Control

Playback of some Internet videos can be limited according to the age of the users. Scenes may be blocked or replaced with different scenes. Set the function in accordance with the onscreen instructions.
To select the output source for each zone

You can select the source that is output to the zone. Audio and video signals are output to zone 2, while only audio signals are output to zone 3.
1 Select the zone to which you want to

output video/audio signals, then press .
Internet Video Unrated

Lets you set whether or not access to allow playback of unrated Internet videos.
2 Select Input, then press 3 Select the input, then press
. .
x Allow
Allows the playback of unrated Internet videos.
To adjust the volume for zone 2

If the SURROUND BACK (ZONE 2) terminals are used with a zone 2 connection, you can also adjust the volume of zone 2. If you set Line Out to Variable, you can also adjust the volume using Zone Control. If you want to adjust the volume of zone 2 in zone 2 using the remote control, see Operating the receiver from another zone (ZONE 2/ZONE 3 operations) (page 82).
x Block
Blocks the playback of unrated Internet videos.
1 Select the zone for which you want to

adjust the volume, then press 116US .
2 Select Volume, then press 3 Adjust the volume, then press
. .
x Off
Lets you turn off output of 12V triggers even when the main receiver is turned on.
Zone Setup
To preset the volume for main zone/zone 2
You can preset the volume of turning the power on for each zone.
x Ctrl
Lets you turn the output of 12V triggers on or off manually using the control command of an external control device. Adjusting Settings
x Zone
Lets you turn the output of 12V triggers on or off based on whether the selected zone is turned on or off. .
1 Select the zone for which you want to

preset the volume, then press .
2 Select Preset Volume, then press 3 Adjust the volume, then press
x Input (for Main only)

Lets you turn on the output of 12V triggers when the preset input is selected. When you select Input, the setting display which sets each input trigger to on/off appears. Press V/v to select the input, then press to check the box.
. During the adjustment, the sound is output at the volume level to which you have adjusted it, regardless of the value of MASTER VOLUME control. If you select Off, each zone is activated at the same volume as that in effect when you turned the power off last time.
x HDMI A (for Main only)

Lets you turn the output of 12V triggers on or off based on the output setting of the HDMI OUT A jack.
Note
You cannot preset the volume in the following cases. The SURROUND BACK (ZONE 2) terminals are used for the surround back speakers or the front high speakers, or are used with a biamplifier connection. Line Out is set to Fixed.
x HDMI B (for Main only)

Lets you turn the output of 12V triggers on or off based on the output setting of the HDMI OUT B jack.
Line Out
You can set the volume control for the ZONE 2 AUDIO OUT jacks to Variable or Fixed. For details, see Set the volume control for zone 2 (page 81)
x Main (for Zone2 and Zone3 only)

Lets you link operation of trigger in zone 2 or zone 3 to the TRIGGER OUT MAIN jack.
x Fixed x Variable
12V Trigger
Lets you select various options for use of the 12V Trigger function.
117US
SPEAKERS (A/B/A+B/OFF)
System Settings
You can customize the settings of the receiver.
?/1
MUSIC
Language
Lets you select the language for the messages on the screen.
x English x Espaol x Franais x Deutsch
1 2
Press ?/1 to turn off the receiver. While holding down MUSIC and SPEAKERS (A/B/A+B/OFF), press ?/1 to turn on the receiver.
Auto Standby
Lets you turn the function that switches the main zone to standby mode automatically if you do not operate the receiver for a specific period of time or when there is no signal input to the receiver on or off.
RS232C Control
Let you turn the control mode for maintenance and service on or off.
x Off x On
x Off
Does not switch to standby mode.
x On
Switches to standby mode after approximately 30 minutes. Note
This function does not work in the following cases. MULTI IN, FM/AM, or SIRIUS is selected. When you play back via a USB device, an iPhone/iPod, a home network, or Internet video.
Software Update Notification

Lets you set whether or not to inform you of newer software version information on the TV screen.
x On x Off
To update the receiver

See Network Update (page 119) to update the software of the receiver. Note
In the following cases, a message appears on the TV screen and the update of the receiver is not performed. When all versions are the latest one.
Settings Lock
Lets you lock the settings of the receiver.
x On
You can only turn this function on using the setting menu. When you turn this function off, perform the following procedure. 118US
When the receiver cannot retrieve the data, such as when the network has not been set up, or when the server is down, etc.
Operating without using the GUI

You can operate the receiver using the display window of the receiver even if the TV is not connected to the receiver. Adjusting Settings
Initialize Personal Information

Lets you erase personal information related to Internet video, such as the Internet content list, Favorites List, etc.
System Information
Displays the software version of the receiver.
EULA
Displays the EULA screen on the TV screen.
Network Update
You can update and improve the functions of the receiver. For information about update functions, refer to the following website: http://www.sony.com/essupport The GUI and display window of the receiver are turned off, and the MULTI CHANNEL DECODING lamp on the front panel flashes during the update. When the update completes, the receiver will restart automatically. It may take about 50 minutes for the update to complete. The time required for the update to complete varies, depending on the speed of the Internet connection. Note
Do not turn the receiver off or disconnect the network cable during software updating. It may cause a malfunction.
AMP MENU V/v/b, RETURN/ EXIT O
Using the menu in the display window
1 2
Turn on the receiver. Press AMP MENU.

The menu is displayed in the display window of the receiver.
Example: When you select SPEAKER SETTINGS.
continued
119US
3 4
Press V/v repeatedly to select the menu, then press . Press V/v repeatedly to select the menu item, then press .
The parameter appears in brackets.
Press V/v repeatedly to select the parameter you want, then press .
The parameter is entered and the brackets disappear from the display.
To return to the previous step

120US
Menu list (in the display window)

The following options are available in each menu. xx in the table signifies the parameter for each item.
Menu Item Parameter
Adjusting Settings
AUTO AUTO CAL START ? CALIBRATION FRONT B CONNECT:xxx? 54321 MEASURING: TONE MEASURING: T.S.P. MEASURING: WOOFER COMPLETE [xxxxxxxxxx]
YES, NO
RETRY, SAVE EXIT, WRN CHECK, PHASE INFO, DIST. INFO, LEVEL INFO, EXIT FL, FR, C, SL, SR, SBR, SBL, SW, LH, RH : 0, 1, 2, 3, 4
WARNING CODE [xxx:4x] NO WARNING PHASE.INFO [xxx:xxx] DIST.INFO [xxxxxxxxxx] LEV.INFO [xxx:xxxxxx]dB ERROR CODE [xxx:3x] RETRY? [xxxx] CANCEL CAL TYPE [xxxxxxxxx] A.P.M. [xxxx] SP RELOCATION [xxxxx] FRONT REF TYPE [xxx] SP PAIR MATCH [xxx] POSITION [xxxxxxxx] NAME IN ? [xxxxxxxx]
FL, FR, C, SL, SR, SBR, SBL, SW, LH, RH :OUT, IN FL, FR, C, SL, SR, SBR, SBL, SW, LH, RH FL, FR, C, SL, SR, SBR, SBL, SW, LH, RH F, SR, SB : 0, 1, 2, 3, 4 YES, EXIT
FULL FLAT, ENGINEER, FRONT REF, USER REF, OFF AUTO, OFF TypeA, TypeB, OFF L/R, L, R ALL, SUR, OFF POS.1, POS.2, POS.3
continued
121US
Menu LEVEL SETTINGS
Item TEST TONE [xxxxxxxx] PHASE NOISE [xxxxxxx]
Parameter OFF, L to RH (AUTO), L to RH (FIX) OFF, L/R, L/C, C/R, R/SR, SR/SBR, SR/SB, SBR/SBL, SR/SL, SB/SL, SBL/SL, SL/L, LH/RH, L/SR, SL/R, L/RH, LH/R OFF, L/R, L/C, C/R, R/SR, SR/SBR, SR/SB, SBR/SBL, SR/SL, SB/SL, SBL/SL, SL/L, LH/RH, L/SR, SL/R, L/RH, LH/R 10.0 dB to +10.0 dB (0.5 dB interval) 10.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 20.0 dB to +10.0 dB (0.5 dB interval) 5 dB to +5 dB (1 dB interval)
PHASE AUDIO [xxxxxxx]
FRONT L [xxx.xdB] FRONT R [xxx.xdB] CENTER [xxx.xdB] SURROUND L [xxx.xdB] SURROUND R [xxx.xdB] SUR BACK [xxx.xdB] SUR BACK L [xxx.xdB] SUR BACK R [xxx.xdB] LEFT HIGH [xxx.xdB] RIGHT HIGH [xxx.xdB] SUBWOOFER [xxx.xdB] ALL SUR LEVEL [xxx.xdB]
122US
Menu SPEAKER SETTINGS
Item SP PATTERN [xxxxx] SB OUTPUT [xxxxxxx] FH OUTPUT [xxxxxxx] FRONT SIZE [xxxxx] CENTER SIZE [xxxxx] SURROUND SIZE [xxxxx] FH SIZE [xxxxx] SB ASSIGN [xxxxx] FRONT L [xxxxxxxxx] FRONT R [xxxxxxxxx] CENTER [xxxxxxxxx] SURROUND L [xxxxxxxxx] SURROUND R [xxxxxxxxx] SUR BACK [xxxxxxxxx] SUR BACK L [xxxxxxxxx] SUR BACK R [xxxxxxxxx] LEFT HIGH [xxxxxxxxx] RIGHT HIGH [xxxxxxxxx] SUBWOOFER [xxxxxxxxx] DISTANCE UNIT [xxxxx] FR CROSSOVER [xxxxx] CNT CROSSOVER [xxxxx] SUR CROSSOVER [xxxxx] FH CROSSOVER [xxxxx] CNT A.DOWN MIX [xxx] SP IMPEDANCE [xohm]
Parameter 5/4.1 to 2/0 (28 patterns) SPEAKER, PREOUT SPEAKER, PREOUT LARGE, SMALL
Adjusting Settings
LARGE, SMALL LARGE, SMALL LARGE, SMALL OFF, BI-AMP, ZONE2
1.0 to 10.0 (m) (1 cm interval) 3 3 to 32 9 (1 inch interval)
meter, feet 40 to 200 (10 Hz interval) 40 to 200 (10 Hz interval) 40 to 200 (10 Hz interval) 40 to 200 (10 Hz interval) OFF, ON 8 ohm, 4 ohm
continued
123US
Menu INPUT SETTINGS
Item NAME IN ? [xxxxxxxx] INPUT SKIP ? xxxxxxxx [xxx] HDMI AUDIO ASSIGN ? xxxxxxxx [xxxxxxxxxx] HDMI VIDEO ASSIGN ? xxxxxxxx [xxxxxxxxxx] DIGITAL A.ASSIGN ? xxxxxxxx [xxxxxxxxxx] COMPONENT V.ASSIGN ? xxxxxxxx [xxxxxxxxxx]
Parameter
SHOWN, HIDDEN
SUR SETTINGS S.F.MODE [xxxxxxxxxx] HD-DCS TYPE [xxxxxxx] T.CONCERT LEV. [xxxx] HEIGHT GAIN [xxxx] EQ SETTINGS FRONT BASS [xxx.xdB] FRONT TREB [xxx.xdB] CENTER BASS [xxx.xdB] CENTER TREB [xxx.xdB] SUR/SB BASS [xxx.xdB] SUR/SB TREB [xxx.xdB] FH BASS [xxx.xdB] FH TREB [xxx.xdB] MULTIZONE SETTINGS P.VOL. MAIN [xxx.xdb] P.VOL. ZONE2 [xxxdb] Z2 LINEOUT [xxxxxxxx] 12V TRIG. MAIN [xxxxx] 12V TRIG. ZONE2 [xxxxx] 12V TRIG. ZONE3 [xxxxx]
FRONT HIGH, STANDARD DYNAMIC, THEATER, STUDIO HIGH, MID, LOW HIGH, MID, LOW 10 dB to +10 dB (0.5 dB interval) 10 dB to +10 dB (0.5 dB interval) 10 dB to +10 dB (0.5 dB interval) 10 dB to +10 dB (0.5 dB interval) 10 dB to +10 dB (0.5 dB interval) 10 dB to +10 dB (0.5 dB interval) 10 dB to +10 dB (0.5 dB interval) 10 dB to +10 dB (0.5 dB interval) OFF, , 92.0 dB to +23.0 dB (0.5 dB interval) OFF, , 92 dB to +23 dB (1 dB interval) FIXED, VARIABLE OFF, CTRL, ZONE, INPUT, HDMIA, HDMIB OFF, CTRL, ZONE, MAIN OFF, CTRL, ZONE, MAIN
124US
Menu TUNER SETTINGS
Item FM MODE [xxxxxx] NAME IN ? [xxxxxxxx] FMxx [xxxxxxxx] NAME IN ? [xxxxxxxx] AMxx [xxxxxxxx] PARENTAL LOCK [xxx] LOCK CODE EDIT SR ANTENNA AIMING SIRIUS ID DISPLAY
Parameter STEREO, MONO
Adjusting Settings
YES, NO
AUDIO SETTINGS
D.L.L. [xxxx] SOUND OPTIMIZER [xxx] AUTO VOLUME [xxx] S.WOOFER MUTING [xxx] A/V SYNC [xxxxxxxxx] DUAL MONO [xxxxxxxx] DEC. PRIORITY [xxxx] D. RANGE COMP. [xxx]
AUTO2, AUTO1, OFF ON, OFF ON, OFF ON, OFF HDMI AUTO, 0 ms to 1200 ms (10 ms interval) MAIN/SUB, MAIN, SUB AUTO, PCM OFF, AUTO, ON DIRECT, AUTO, 480/576i, 480/576p, 720p, 1080i, 1080p 480/576i, 480/576p, 720p, 1080i ON, OFF ON, OFF ON, OFF AMP, TV+AMP AUTO, +10 dB, 0 dB ON, OFF ON, OFF ON, OFF ON, OFF ON, OFF
VIDEO SETTINGS
RESOLUTION [xxxxxxxx] ZONE RESO. [xxxxxxxx]
HDMI SETTINGS
CTRL FOR HDMI [xxx] PASS THROUGH [xxxx] H.A.T.S. [xxx] AUDIO OUT [xxxxxx] SW LEVEL [xxxdB] SW LPF [xxx] VIDEO DIRECT [xxx]
SYSTEM SETTINGS
RS232C CONTROL [xxx] NETWORK STANDBY [xxx] AUTO STANDBY [xxx] VERSION [x.xxx]
continued
125US
To change the display

The display panel provides various information of the receiver status such as sound field.
1 Select the input for which you want to

check the information.
2 Press DISPLAY MODE on the receiver

repeatedly. Each time you press DISPLAY MODE, the display will change as follows. Input you selected t Sound field type t Stream information* t Input name you entered ...
* Stream information may not be displayed.
When listening to FM and AM radio Station name t Frequency t Sound field type ... Index name appears only when you have assigned one to the input or preset station. Index name does not appear when only blank spaces have been entered. When tuning in a channel from the Sirius satellite radio Channel name t Channel number t Category t Artist name t Song title t Composer name t Signal strength t Sound field type
126US
Operating the equipment connected to the receiver
Operating each equipment using the remote control

You can control Sony or non-Sony equipment you are using with the remote control supplied with the receiver. The remote control is initially set to control Sony equipment. When you change the settings of the remote control according to the equipment you are using, you can control non-Sony and other Sony equipment that the remote control is initially unable control (page 128).
Press the input button that matches the connected equipment that you want to operate. Press the appropriated buttons to use the function listed in the table below.
Note
You may not be able to operate some functions for the equipment you are using.
Table of buttons used to control each equipment

Equipment TV Button AV ?/1 Numeric buttons TV INPUT GUIDE -/-ENT/MEM Color buttons TOOLS/OPTIONS DISPLAY RETURN/EXIT V/v/B/b, HOME ./> B/b m/TUNING , M/TUNING + DISC SKIP N, X, x MUTING, TV VOL +/ PRESET +/, TV CH +/ , VCR DVD player, Blu-ray DVD/VCR Disc combo Player HDD Recorder PSX Video CD player, LD player Digital CATV terminal DSS Tape DAT deck A/B deck CD player, MD deck
z z z z z z z z z z z z z z
z z
z z
z z
z z
z z
z z
z z
z z z
z z
z z
zc) z z z z zc) z z z z z z z z z z z zc)
z z z z z z z z z z z z z
z z z z z z z z z z z
z z z z za)
z z z z z z z z z z
z z z z z z z z zd) z z z
z z z z z z z
z z z z zb) z z z
z z
z z z
za)
continued
127US
Equipment TV Button TOP MENU, POP UP/MENU AUDIO SUBTITLE

a) b) c) d)
VCR DVD player, Blu-ray DVD/VCR Disc combo Player
HDD Recorder
PSX
Video CD player, LD player
Digital CATV terminal
DSS
Tape DAT deck A/B deck
CD player, MD deck
z z z z z z
z z z z z
z z z z
LD player only Deck B only DVD only Video CD only
Turning off all connected equipment

(SYSTEM STANDBY)
Even when this receiver is standby mode, zone 2 or zone 3 remain turned on. To turn off all Sony equipment, including connections to each zone, press ?/1 and AV ?/1 on the remote control at the same time.
AV ?/1
Programming the remote control

You can customize the remote control to match the equipment connected to your receiver. You can even program the remote control to operate non-Sony equipment and also Sony equipment that the remote control is normally unable to operate. The procedure below uses as an example a case in which a VCR made by a company other than Sony is connected to the VIDEO 1 IN jacks on the receiver.
RM SET UP SHIFT Input buttons Numeric buttons AV ?/1
?/1
ENT/ MEM
Press AV ?/1 while pressing RM SET UP.

The RM SET UP button flashes.
128US
While the RM SET UP button is flashing, press the input button (including the TV button) of the equipment you want to control.
For example, if you are going to control a VCR connected to VIDEO 1 IN jack, press VIDEO 1. RM SET UP and SHIFT light up, and the input button flashes. If you press the button for an equipment of which you cannot program the remote control, such as TUNER, PHONO, or SOURCE, etc., the RM SET UP button keeps flashing.
The numeric codes corresponding to the equipment and the maker of the equipment
Use the numeric codes in the tables below to program non-Sony equipment and also Sony equipment that the remote control is initially unable to operate. Since the signal from the remote control received by the equipment differs by its model and the year, more than one numeric code may be assigned to an equipment. If you fail to program your remote control using one of the codes, try using other codes. Notes
The numeric codes are based on the latest information available for each brand. There is a chance, however, that your equipment will not respond to some or all of the codes. All of the input buttons on this remote control may not be available when used with your particular equipment.
Press the numeric buttons to enter the numeric code.

The input button lights up. If more than one code exists, trying entering the first one which corresponds to the equipment. Note
Only the codes in the 500s are valid for the TV button.
To control a CD player
Maker SONY DENON JVC KENWOOD MAGNAVOX MARANTZ ONKYO PANASONIC PHILIPS PIONEER TECHNICS YAMAHA Code(s) 101, 102, 103 104, 123 105, 106, 107 108, 109, 110 111, 116 116 112, 113, 114 115 116 117 115, 118, 119 120, 121, 122
Press ENT/MEM.
Once the numeric code has been verified, the RM SET UP button flashes twice and the remote control automatically exits the programming mode. The input button also turns off.
To cancel programming
Press RM SET UP during any step.
To control a DAT deck

Maker SONY PIONEER Code(s) 203 219
To control a tape deck

Maker SONY Code(s) 201, 202
continued
129US
Maker DENON KENWOOD NAKAMICHI PANASONIC PHILIPS PIONEER TECHNICS YAMAHA
Code(s) 204, 205 206, 207, 208, 209 210 216 211, 212 213, 214 215, 216 217, 218
Maker TOSHIBA ZENITH
Code(s) 404, 421 418, 420
To control a DVD/VCR COMBO (recorder)

Maker SONY Code(s) 411
To control an MD deck
Maker SONY DENON JVC KENWOOD Code(s) 301 302 303 304
To control a HDD/DVD COMBO (recorder)

Maker SONY Code(s) 401, 402, 403
To control a TV
Maker SONY AIWA AKAI AOC CENTURION CORONADO CURTIS-MATHES DAYTRON DAEWOO FISHER FUNAI FUJITSU GOLDSTAR/LG GRUNDIG HITACHI ITT/NOKIA J.C.PENNY JVC KMC MAGNAVOX MARANTZ MITSUBISHI/MGA NEC NORDMENDE NOKIA PANASONIC PHILIPS PHILCO Code(s) 501 501, 536, 539 503 503 566 517 503, 551, 566, 567 517, 566 504, 505, 506, 507, 515, 544 508, 545 548 528 503, 512, 515, 517, 534, 544, 556, 568, 576 511, 533, 534 503, 513, 514, 515, 517, 519, 544, 557, 571 521, 522 503, 510, 566 516, 552 517 503, 515, 517, 518, 544, 566 527 503, 519, 527, 544, 566, 568 503, 517, 520, 540, 544, 554, 566 530, 558 521, 522, 573, 575 509, 524, 553, 559, 572 515, 518, 557, 570, 571 503, 504, 514, 517, 518
To control an HDD recorder

To control a Blu-ray Disc Player

Maker SONY LG PANASONIC SAMSUNG Code(s) 310, 311, 312 337 335 336
To control a PSX
To control a DVD player

Maker SONY BROKSONIC DENON HITACHI JVC MITSUBISHI ORITRON PANASONIC PHILIPS PIONEER RCA SAMSUNG Code(s) 401, 402, 403 424 405 416 415, 423 419 417 406, 408, 425 407 409, 410 414 416, 422
130US
Maker PIONEER PORTLAND QUASAR RADIO SHACK RCA/PROSCAN SAMSUNG
SAMPO SABA SANYO SCOTT SEARS SHARP SYLVANIA THOMSON TOSHIBA TELEFUNKEN TEKNIKA WARDS YORK ZENITH GE LOEWE
Code(s) 509, 525, 526, 540, 551, 555 503 509, 535 503, 510, 527, 565, 567 503, 510, 523, 529, 544 503, 515, 517, 531, 532, 534, 544, 556, 557, 562, 563, 566, 569 566 530, 537, 547, 549, 558 508, 545, 546, 560, 567 503, 566 503, 508, 510, 517, 518, 551 517, 535, 550, 561, 565 503, 518, 566 530, 537, 547, 549 535, 539, 540, 541, 551 530, 537, 538, 547, 549, 558 517, 518, 567 503, 517, 566 566 542, 543, 567 503, 509, 510, 544 515, 534, 556
Maker GOLDSTAR/LG GRUNDIG HITACHI ITT/NOKIA JVC MAGNAVOX MITSUBISHI/MGA NEC PANASONIC PHILIPS PIONEER RCA/PROSCAN SAMSUNG SANYO SHARP TELEFUNKEN TOSHIBA ZENITH
Code(s) 723, 753 724 722, 725, 729, 741 717 726, 727, 728, 736 730, 731, 738 732, 733, 734, 735 736 729, 730, 737, 738, 739, 740 729, 730, 731 729 722, 729, 730, 731, 741, 747 742, 743, 744, 745 717, 720, 746 748, 749 751, 752 747, 756 754
* If an AIWA VCR does not work even though you enter the code for AIWA, enter the code for Sony instead.
To control a satellite tuner (box)

Maker SONY AMSTRAD BskyB GENERAL ELECTRIC(GE) GRUNDIG HUMAX THOMSON PACE PANASONIC PHILIPS Code(s) 801, 802, 803, 804, 824, 825, 865 845, 846 862 866 859, 860 846, 847 857, 861, 864, 876 848, 849, 850, 852, 862, 863, 864 818, 855 856, 857, 858, 859, 860, 864, 874 851, 853, 854, 864 866, 871 868 867 873 872 875 869, 870
To control an LD player
Maker SONY PIONEER Code(s) 601, 602, 603 606
To control a video CD player

Maker SONY Code(s) 605
To control a VCR
Maker SONY AIWA* AKAI BLAUPUNKT EMERSON FISHER GENERAL ELECTRIC (GE) Code(s) 701, 702, 703, 704, 705, 706 710, 750, 757, 758 707, 708, 709, 759 740 711, 712, 713, 714, 715, 716, 750 717, 718, 719, 720 721, 722, 730
NOKIA RCA/PROSCAN HITACHI/BITA HUGHES JVC/Echostar/Dish Network MITSUBISHI SAMSUNG TOSHIBA
continued
131US
To control a cable box

Maker SONY HAMLIN/REGAL JERROLD/G.I./ MOTOROLA JERROLD OAK PANASONIC PHILIPS PIONEER RCA SCIENTIFIC ATLANTA TOCOM/PHILIPS ZENITH Code(s) 821, 822, 823 836, 837, 838, 839, 840 806, 807, 808, 809, 810, 811, 812, 813, 814, 819 830, 831 841, 842, 843 816, 826, 832, 833, 834, 835 830, 831 828, 829 805 815, 816, 817 830, 831 826, 827
Performing several commands in sequence automatically

(Macro Play)
The Macro Play function lets you link several commands in a sequential order as a single command. The remote control provides 2 macro lists (MACRO 1 and MACRO 2). You can specify up to 20 commands for each macro list.
RM SET UP AMP
Input buttons
MACRO 1 MACRO 2
132US
Program the sequence of the operation
To cancel programming
Not pressing any button for 60 seconds cancels the settings. The previous command remains valid.
Press MACRO 1 or MACRO 2 for more than 1 second while pressing RM SET UP.
The RM SET UP button flashes and one of the input buttons lights up (as the factory default setting, the BD/DVD button lights).
Starting macro play
1 2
Press AMP.
The AMP button lights up, and then turns off. Using the Remote Control
Press the input button for the equipment for which you want to program the sequence of operation(s). Press the buttons you want to program in the same sequence as you want the operation(s) to be performed.
You can program particular operations using the following buttons. Press Operations to be programmed
Press MACRO 1 or MACRO 2 to start the macro.

The macro starts and execute the commands in the order you assigned them. While the commands are being sent, the AMP button flashes and the RM SET UP button lights up. When the commands have been sent, the RM SET UP and AMP buttons turn off.
To erase a programmed macro 1 Press MACRO 1 or MACRO 2 for more

than 1 second while pressing RM SET UP to clear the stored macro. The RM SET UP button flashes.
The input Switches inputs. button for more than 1 second MACRO 1 or MACRO 2 Make a one second interval. When you want to make a longer interval, press MACRO 1 or MACRO 2 repeatedly.
2 Press RM SET UP.

Settings stored as macro are cleared.
The input button selected in step 2 flashes twice, then lights up again.
Setting remote control codes that are not stored in the remote control
Even if a remote control code is not one of the presets stored in the remote control, it is possible for the remote control to learn the code using the learning function.
4 5
Repeat steps 2 and 3 when you want to program operations for other equipment. Press RM SET UP to finish the programming process.
continued
133US
FAVORITES
RM SET UP ?/1
SHIFT
Press the input button (including the TV button) for the equipment you want to operate with the new command.
The input button flashes. (The RM SET UP button remains lit.) Even if you press an input button on which you cannot store a new command such as SOURCE, etc., the input button will not flash.
Input buttons
Buttons used to learn code*
Buttons used to learn code
Press the button on which you want to store the new command. For the buttons with an asterisk in the illustration above, press SHIFT, then press the button.
The input button you selected in step 2 lights up. (The RM SET UP button remains lit.) When the learning process fails, the RM SET UP button flashes five times. If you fail to store the new command, make sure that a command has not already been stored on the button on which you want to store the new command. If you want to store the new command on the button on which you have already stored the command, erase the stored command beforehand.
* To store a new command on one of those buttons, press SHIFT beforehand.
Press FAVORITES while pressing RM SET UP.

The RM SET UP button lights up. When the memory capacity for storing remote control codes reaches a certain limit, the RM SET UP button flashes 10 times, and then the learning process is finished.
Point the remote control code receiver section of the remote control toward the transmitter on the remote control to be learned from.
About 5 cm - 10 cm (2" - 4")
134US
Press the button on the remote control to be learned from to transmit the remote control code.
While the remote control of the receiver is receiving the signal, the input button selected in step 2 turns off. The RM SET UP button flashes twice, then the learning process is completed. When the learning process fails, the RM SET UP button flashes five times. Try to perform process again from step 2.
The RM SET UP button flashes twice, then the clearing process is completed. When the clearing process fails, the RM SET UP button flashes five times. Try to perform process again from step 2.
5 Press RM SET UP to finish the erasing

process.
Press RM SET UP to finish the learning function process.
Clearing the memory of the multifunction remote control

AV ?/1 RM SET UP ?/1
To cancel learning
Press RM SET UP. Also, not pressing any button for 60 seconds cancels the settings. However, after performing step 3, you cannot cancel the settings even if you press RM SET UP. In this case, after leaving the remote control untouched for 10 seconds, press RM SET UP to cancel the settings.
Using a command that has been learned

When selecting a learned input, press the button used to learn that function.
To erase the learned code 1 Press FAVORITES while pressing RM

SET UP.
2 Press the input button for which you

want to clear the setting. The input button flashes. (The RM SET UP button remains lit.)
MASTER VOL
3 Press ?/1 for more than 1 second.

The input button flashes twice, repeatedly.
4 Press the button which learned the

command to clear the stored setting.
continued
135US
Hold down ?/1 while pressing MASTER VOL , then press AV ?/1, all at the same time.
The RM SET UP button flashes three times.
Release all buttons.

All the contents of the remote controls memory (e.g., all the programmed data) are cleared.
136US
Precautions
On safety
Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further.
Do not place the receiver near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock. Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions.
On cleaning
Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. Additional Information If you have any questions or problems concerning your receiver, please consult your nearest Sony dealer.
On power sources
Before operating the receiver, check that the operating voltage is identical with your local power supply. The operating voltage is indicated on the nameplate on the back of the receiver. If you are not going to use the receiver for a long time, be sure to disconnect the receiver from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer. AC power cord (mains lead) must be changed only at a qualified service shop.
On heat buildup
Although the receiver heats up during operation, this is not a malfunction. If you continuously use this receiver at a large volume, the cabinet temperature of the top, side and bottom rises considerably*. To avoid burning yourself, do not touch the cabinet.
* The top of the cabinet may become too hot to touch.
On placement
Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver.
137US
Troubleshooting
If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer.
flowing in the internal circuits of the receiver, and this is normal.
Video
There is no picture or an unclear picture appears on the TV screen or monitor, regardless of type of picture. Select the appropriate input on the receiver (page 54). Set your TV to the appropriate input mode. Move your TV away from the audio equipment. Assign the component video input correctly (page 88). The input signal should be same as input when you are up-converting an input signal with this receiver (page 22). Make sure that cables are correctly and securely connected to equipment. Depending on the playback equipment, equipment may need to be set up. Refer to the operating instructions supplied with the each equipment. Images appear later than the associated sound is played. Depending on the equipment connected to the HDMI jack, or the source played back, images may appear later than the associated sound. In this case, change the setting of A/V Sync in the Audio Settings menu (page 108). Recording cannot be carried out. Check that the equipment are connected correctly (page 30). Select the source equipment (page 54). Check the connection of the recording deck according to the video signals you want to record. Analog input signals (composite video) can be output only from the analog output jacks. Video input signals via the HDMI IN jacks cannot be recorded. Copyright protection to prevent recording is contained in the sources. In this case,
General
The receiver is turned off automatically. Auto Standby is set to On (page 118). The sleep timer function is working (page 94). PROTECTOR is working (page 147). The receiver is turned on automatically. Control for HDMI is set to On or Pass Through is set to Off. In this case, the receiver may be turned on by operating other equipment connected to it. No picture and no sound are output, or the picture and sound are corrupted. The receiver is placed near equipment such as a television, VCR, or tape deck. If the receiver is being used in combination with a television, VCR, or tape deck, and is placed too close to that equipment, noise may result, and picture quality may suffer. This is especially likely when using an indoor antenna (aerial). Therefore, we recommend using an outdoor antenna (aerial). The top of the receiver is hot. Phenomenon is specific to this amplifier. This is not a malfunction. If Control for HDMI, Pass Through, or Network Standby is set to On, or the power for zone 2 or zone 3 is turned on, the top of the receiver may become hot even while the receiver is in standby mode. This condition occurs because current is
138US
you may not be able to record from the sources. Set Auto Standby to Off (page 118). While only composite video signals are being recorded, the auto standby function of the receiver may start up and interrupt the recording. Specific type of image is not output or corrupted. Component video output The resolution of output signals from the COMPONENT VIDEO OUT jacks may not be supported by your TV. In this case, select the appropriate resolution on the receiver (page 109). COMPONENT VIDEO MONITOR OUT jacks have restrictions on resolution when the resolution of video signals protected by copyright technology is converted. The resolution of the signals output to the COMPONENT VIDEO MONITOR OUT jacks is converted up to 480p/576p. HDMI output The output of the HDMI video signals of the receiver may be set to OFF. In this case, select HDMI A or HDMI B using the HDMI OUTPUT button (page 86). If the compatible video format differs between the monitors connected to the HDMI OUT A jack and the HDMI OUT B jack of the receiver, HDMI A + B may not work. In this case, select HDMI A or HDMI B using the HDMI OUTPUT button (page 86). Depending on the playback equipment you connect, HDMI A + B may not work. If the image is not output due to settings on the playback equipment, set the output setting on the playback equipment to auto. Be sure to use a connecting cable for the HDMI jack corresponding to High Speed HDMI cable when you view images or listen to sound, especially for the 1080p, Deep Color, or 3D transmission.
Set Video Direct to On in the HDMI Settings menu in the following cases. Images from the equipment connected to the HDMI jack may be distorted. Images or sound from the equipment connected to the HDMI jack may be interrupted when video signals are switched. The start of the video is not output when the 3D video is switched, or the colors of the 3D video are improper. 3D image Depending on the TV or the video equipment, 3D images may not be displayed. Check the 3D image formats supported by the receiver (page 150). VCR If you use a VCR without an image improvement circuit, such as TBC, the images may be distorted. AdobeRGB or AdobeYCC601 Set Video Direct to On to receive AdobeRGB or AdobeYCC601 signals. When you select My Video, My Music, My Photo, Internet Video, Internet Music, Internet Photo, Internet Network, or Sony Entertainment Network from the Watch/Listen menu, no picture is output. Select BD/DVD using INPUT SELECTOR on the receiver once, then set Playback Resolution to 480p/576p in the Video Settings menu using the GUI (page 111), and select the content again. The Pass Through function does not work. HDMI B is selected. Select HDMI A or HDMI A + B using the HDMI OUTPUT button.
139US
Audio
There is no sound, no matter which equipment is selected, or only a very low-level sound is heard. Check that the speakers and equipment are connected correctly. Check that both the receiver and all equipment are turned on. Check that MASTER VOLUME control is not set at dB. Try to set it at about 40 dB. Check that SPEAKERS (A/B/A+B/OFF) is not set to OFF (page 10). Press MUTING on the remote control to cancel the muting function. Try pressing the input button on the remote control or INPUT SELECTOR on the receiver to select the equipment of your choice. Check that headphones are not connected. When you want to listen to the sound from the TV speaker, set Audio Out to TV+AMP in the HDMI Settings menu. If set to AMP, the sound is not output through the TV speaker. If you output the multi-channel sound from the receiver, set to AMP. Sound may be interrupted when the sampling frequency, the number of channels or audio format of audio output signals from the playback equipment is switched. Set the EQ setting of the iPhone/iPod to Off or Flat. There is severe hum or noise. Check that the speakers and equipment are connected correctly. Check that the connecting cords are away from a transformer or motor, and at least 3 meters away from a TV set or fluorescent light. Move your TV away from the audio equipment.
Make sure you have grounded the U SIGNAL GND terminal (only when a turntable is connected). The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. There is no sound from specific speaker(s). Front Connect headphones to the PHONES jack to verify that sound is output to the headphones. If only one channel is output to the headphones, check that all the cords are fully inserted into the jacks on both the receiver and the equipment. If both channels are output to the headphones, check the connection of the front speaker which is not outputting any sound. Make sure you have connected both the L and R jacks to an monaural equipment, analog equipment requires both L and R jack connections. Use a monaural-stereo cable (not supplied). However, there will be no sound from the center speaker when a sound field (Pro Logic, etc.) is selected. Center/surround/surround back Check that the speaker settings are appropriate for the setup using Auto Calibration or Speaker Connection in the Speaker Settings menu. And then check that sound is output from each speaker correctly, using Test Tone in the Speaker Settings menu. Select the HD-D.C.S. sound field (page 72). Adjust the speaker level (page 104). Make sure the center/surround speaker(s) is (are) set to either Small or Large.
140US
Surround back Some discs have no Dolby Digital Surround EX information. If the speaker pattern is set so that there are no surround back speakers, the input signals to the SUR BACK jacks is invalid, because the receiver cannot down-mix the surround back channels. Subwoofer Check that the subwoofer is connected correctly and securely. Make sure you have turned on your subwoofer. There is no sound from a specific equipment. Check that the equipment is connected correctly to the audio input jacks for that equipment. Check that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the equipment. Set the INPUT MODE to AUTO (page 88). HDMI input When 2ch Analog Direct is being used, the sound is not output. Use other sound field (page 71). Check the HDMI connection (page 30, 32, 34, 37). Check that you use an HDMI cable that have an HDMI logo authorized by HDMI Licensing LLC. Depending on the playback equipment, equipment may need to be set up. Refer to the operating instructions supplied with the each equipment. Be sure to use a connecting cable for the HDMI jack corresponding to High Speed HDMI cable when you view images or listen to sound during a 1080p, Deep Color, or 3D transmission. Sound may not be output from the receiver while the GUI appears on the TV screen. Press HOME to turn the GUI off.
Audio signals (format, sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected equipment. Check the setup of the connected equipment if an image is poor or the sound does not come out of an equipment connected via the HDMI cable. When the connected equipment is not compatible with copyright protection technology (HDCP), the image and/or the sound from the HDMI OUT jack may be distorted or may not be output. In this case, check the specification of the connected equipment. Set the image resolution of the player to more than 720p/1080i to enjoy High Bitrate Audio (DTS-HD Master Audio, Dolby TrueHD). The image resolution of player may need certain settings be made before you can enjoy DSD and multi-channel Linear PCM. Refer to the operating instructions of the player. Make sure the TV is compatible with the System Audio Control function. If the TV does not have System Audio Control function, set the Audio Out settings in the HDMI Settings menu to TV+AMP if you want to listen to the sound from the TV speaker and receiver. AMP if you want to listen to the sound from the receiver. When you connect the receiver to a video equipment (projector, etc.), sound may not be output from the receiver. In this case, select AMP. You cannot listen to the sound of an equipment connected to the receiver while a TV is selected as the input on the receiver. Be sure to change the input of the receiver to HDMI when you want to watch a program on an equipment connected to the receiver. Change the TV channel when you want to watch a TV broadcast.
continued
141US
Be sure to select the correct equipment or input you want when you watch a program from the equipment connected to the TV. When using the Control for HDMI function, you cannot control the connected equipment using TVs remote control. Depending on the connected equipment and TV, you may need to set up the HDMI setting of the equipment and TV. Refer to the operation instructions supplied with each equipment and TV. Change the input of the receiver to the HDMI input connected to the equipment. Coaxial/optical input When 2ch Analog Direct is being used, the sound is not output. Use other sound field (page 71). Check the INPUT MODE (page 88). Check to make sure the selected audio (digital) input jack is not assigned to other inputs in Audio Input Assign in the Input Settings menu (page 88). Analog 2 channel input Check to make sure the selected audio (analog) input jack is not assigned to other inputs in Audio Input Assign in the Input Settings menu (page 88). The left and right sounds are unbalanced or reversed. Check that the speakers and equipment are connected correctly. Adjust the balance parameters using the Speaker Setup in the Speaker Settings menu. Adjust the level of the speakers. Dolby Digital or DTS multi-channel sound is not reproduced. Check that the DVD, etc., you are playing is recorded in Dolby Digital or DTS format. When connecting the DVD player, etc., to the digital input jacks of this receiver, make sure the digital audio output setting on the connected equipment. 142US
You can enjoy High Bitrate Audio (DTSHD Master Audio, Dolby TrueHD), DSD, and multi-channel Linear PCM with an HDMI connection only. Multi-channel sound cannot be output. When Control for HDMI is set to On, Audio Out may be automatically set to AMP. In this case, set Audio Out to AMP. The surround effect cannot be obtained. Make sure the sound field function is on (press MOVIE/HD-D.C.S. or MUSIC). PLII (Movie/Music), PLIIx (Movie/ Music), PLIIz Height, and Neo:X (Cinema/Music/Game) do not work when the speaker pattern is set to 2/0 or 2/ 0.1. The MULTI CHANNEL DECODING lamp does not light up in blue. Check that the playback equipment is connected on a digital jack and the input is selected properly on this receiver. Check whether the input source of the software being played back corresponds to the multi-channel format. Check whether the setup on the playback equipment is set to multi-channel sound. Check to make sure the selected audio (digital) input jack is not assigned to other inputs in Audio Input Assign in the Input Settings menu (page 88). Recording cannot be carried out. Check that the equipment are connected correctly (page 39). Select the source equipment (page 54). Audio input signals via the HDMI IN and MULTI CHANNEL INPUT jacks cannot be recorded. Check the connection of the recording deck according to the audio signals you want to record. Analog input signals can be output only from the analog output jacks. Digital audio input signals can be output only from the OPTICAL OUT jack.
You may not make recordings using an SCMS-compliant recording deck. Copyright protection to prevent recording is contained in the sources. In this case, you may not be able to record from the sources. A test tone is not output from the speakers. The speaker cords may not be connected securely. Check to see if they are connected securely and cannot be disconnected by pulling on them slightly. The speaker cords may have the shortcircuit problem. A test tone is output from a different speaker than the speaker displayed on the screen. The speaker configuration set up is incorrect. Make sure that the speaker connections and the configuration match correctly. The H.A.T.S. function does not work. Audio Out is set to TV+AMP. Select AMP for Audio Out. TheH.A.T.S. function may not work, depending on the speaker pattern or settings.
Outdoor FM antenna (aerial)
Receiver
Ground (earth) wire (not supplied) To ground
Tuner
The FM reception is poor. Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna (aerial) as shown on page 143. If you connect the receiver to an outdoor antenna (aerial), ground it against lightning. To prevent a gas explosion, do not connect the ground (earth) wire to a gas pipe.
Radio stations cannot be tuned in. Check that the antennas (aerials) are connected securely. Adjust the antennas (aerials) and connect an external antenna (aerial), if necessary. Keep the satellite radio antenna, away from the speaker cords and the power cord to avoid picking up noise. The signal strength of the stations is too weak with automatic tuning. Use direct tuning. No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations is used). Preset the stations (page 63). Press DISPLAY MODE on the receiver so that the frequency appears on the display window. The system cannot receive satellite channels at all. The receiving condition is not good. Move the antenna to the place where the condition is good. Check that you subscribed to the desired satellite radio service (page 64).
USB device
The USB device is not recognized. Turn off the receiver, then disconnect the USB device. Turn on the receiver again and reconnect the USB device.
continued
143US
Connect the supported USB device (page 55). The USB device does not work properly. Refer to the USB device operating instruction on how to deal with this problem. Content on the USB device is not displayed. The hierarchy of folders has exceeded 4 levels. The receiver can display content in only up to 4 levels (including the ROOT folder). However, folders in a 4th level folder are not displayed. No sound is output. Turn off the receiver, then disconnect the USB device. Turn on the receiver again and reconnect the USB device. Connect the supported USB device (page 55). Press N to start playback. When 2ch Analog Direct is being used, the sound is not output. Use other sound field (page 71). The music data itself contains noise, or the sound is distorted. Depending on the file format, there may be files that sometimes cannot be played back. For details, see Playable types of files (page 151). USB device formatted with file systems other than FAT12/16/32, VFAT, or NTFS are unsupported.* If you use partitioned USB device, only audio files on the first partition can be played back. Playback is possible up to 4 levels (including the ROOT folder). The number of files in a folder has exceeded 500 (including folders). Files that are encrypted or protected by passwords, etc. cannot be played back. If you play back music files stored on a WALKMAN using the receiver, move the files to the WALKMAN from a computer by Click & Drop, then save them on the
WALKMAN in a format supported by the receiver (e.g., MP3).

* This receiver supports FAT12/16/32, VFAT, or NTFS, but some USB device may not support all of these file systems. For details, refer to the operating instruction of each USB device or contact the manufacturer.
The USB device cannot be connected into the (USB) port. The USB device is being connected upside down. Connect the USB device in the correct orientation. Erroneous display. The data stored in the USB device may have been corrupted. The character codes that can be displayed by this receiver are as follows: Upper case (A to Z) Lower case (a to z) Numbers (0 to 9) Symbols ( < > * + , . / @ [ \ ] _ ) Other characters may not be displayed correctly. It takes a long time before playback starts. The reading process can take a long time in the following cases. There are many folders or files on the USB device. The file structure is extremely complex. The memory capacity is excessive. The internal memory is fragmented. Thus, we recommend following the guideline. Total files per folder: 500 or less
iPhone/iPod
The iPhone/iPod cannot be charged. Check that the receiver is turned on. Make sure the iPhone/iPod is connected firmly.
144US
The iPhone/iPod cannot be operated. Check that you have removed the protect case of the iPhone/iPod. Depending on the contents of the iPhone/ iPod, it may take time to start playback. Turn off the receiver, then disconnect the iPhone/iPod. Turn on the receiver again and reconnect the iPhone/iPod. You are using an unsupported iPhone/ iPod. See Compatible iPhone/iPod models (page 60) for the supported device types. The ring volume of the iPhone does not change. Adjust the ring volume using the controls on the iPhone.
Register the receiver with the server. For details, refer to the instructions supplied with the server. Wait for a few moments, and then try connecting to the server again. Cannot find or play back the content on the server. On the My Music, My Photo, and My Video screens, the receiver displays only the content that can be played back with the receiver from among the content offered by the server within the DLNA guidelines. There may be content that is not played back or displayed even if that content is defined in the DLNA guidelines. Cannot access the receiver from ES Remote or the DLNA controller. Make sure the controller you want to use is set to Allow in Renderer Access Control (page 115). If you set Auto Access Permission to On in Renderer Options (page 115), any controller detected can be available automatically. Is the network controller listed on Renderer Options, and is it set to Allow? If the box is not checked, check the box for Auto Access Permission, and return to the home menu. Then, operate the receiver using the network controller once, and then uncheck the box for Auto Access Permission, if necessary. If the network controller is a computer software controller, is the software filtered by antivirus software or firewall software? Permit UPnP communications between the software and the receiver. For details, refer to the operating instructions of the antivirus software, firewall software, or network controller software.
Network
Cannot connect to the network. Check the network connection (page 45) and the Network Settings menu (page 115). Cannot find the server. Search the server using Connection Server Settings in the Network Settings menu (page 115). Check the following: Is the router turned on? If there is another device between the receiver and the router, check that device is turned on. Are all of the cables connected correctly and securely? Is the settings to make sure that they match the routers settings (DHCP or fixed IP address)? When using a computer, check the following: The built-in firewall settings for the computers operating system. The firewall settings of your security software. To check the firewall settings of your security software, refer to your security softwares Help section.
145US
Internet video
The picture/sound is poor/certain programs display with a loss of detail, especially during fastmotion or dark scenes. Picture/sound quality may be poor, depending on Internet content providers. Picture/sound quality may be improved by changing the connection speed. Sony recommends a connection speed of at least 2.5 Mbps for standard definition video and 10 Mbps for high-definition video. Not all videos contain sound. The picture is small. Press V to zoom in. Cannot play back content. Some Internet content requires registration via a computer before it can be played.
BRAVIA Sync (Control for HDMI)

The Control for HDMI function does not work. Check the HDMI connection (page 28, 30, 32, 34). Make sure Control for HDMI is set to On in the HDMI Settings menu. Make sure the connected equipment is compatible with the Control for HDMI function. Check the Control for HDMI settings on the connected equipment. Refer to the operating instructions of the connected equipment. If you change the HDMI connection, connect/disconnect the AC power cord (mains lead), or there is a power failure, repeat the procedures of Preparing for the BRAVIA Sync (page 84). When you select HDMI B or OFF, the Control for HDMI function does not work properly.
If you select HDMI A or HDMI A + B, after you have selected HDMI B or OFF, the Control for HDMI function may not work properly for a while. This is because the equipment connected to the HDMI OUT A jack must re-recognize the receiver that is equipped with the Control for HDMI function. If the Control for HDMI function does not work properly for a long time, perform the steps given in Preparing for the BRAVIA Sync (page 84). The types and the number of equipment which can be controlled by the BRAVIA Sync are restricted in the HDMI CEC standard as follows. Recording equipment (Blu-ray Disc recorder, DVD recorder, etc.): up to 3 equipment Playback equipment (Blu-ray Disc Player, DVD player, etc.): up to 3 equipment Tuner-related equipment: up to 4 equipment AV receiver (audio system): up to 1 equipment When you try to use the One-Touch Play function, input is not switched as intended. Check the assignment of the HDMI input (page 88). When you assign multiple inputs with the same HDMI input jack, if you use the One-Touch Play function on the equipment connected to the HDMI input, the previous input, in its original input sequence, is preferentially selected. The Audio Return Channel (ARC) does not work. Make sure Control for HDMI is set to On in the HDMI Settings menu. Make sure that the INPUT MODE for TV is set to AUTO (page 88).
146US
Remote control
The remote control does not function. Point the remote control at the remote sensor on the receiver (page 10). Remove any obstacles in the path between the remote control and the receiver. Replace all the batteries in the remote control with new ones, if they are weak. Make sure that the command modes of the receiver and the remote control are the same. If the command mode of the receiver and the remote control are different, you cannot operate the receiver with the remote control (page 95). Make sure you select the correct input on the remote control. When you operate a programmed nonSony equipment, the remote control may not function properly, depending on the model and the maker of the equipment. The RM SET UP button flashes and you cannot set up Macro Play (page 132) or the remote control cannot learn a remote control code (page 133). When the RM SET UP button flashes five times, replace the batteries with new ones. If the trouble is other than one of the cases described above and the trouble is not solved even if you wait for a while, perform either of the operations below. Press ?/1 on the remote control to turn the receiver off and then on again. Hold down ?/1 on the receiver until the lamp above the button flashes in green to reboot the receiver.
PROTECTOR The receiver is covered and ventilation holes are blocked. The receiver will automatically turn off after a few seconds. Remove the object covering the upper panel of the receiver and turn on the power again. SPEAKER SHORTED Irregular current is output to the speakers due to a short circuit on the speaker terminals. The receiver will automatically turn off after a few seconds. If the protective device on the receiver is activated due to a short-circuit problem, turn off the receiver. Check the connection of the speakers and turn on the power again. FAN STOPPED Check that the ventilation hole on the top of the receiver are not blocked. Place the receiver in a location with adequate ventilation to prevent heat build-up in the receiver. A new software version is available. Please go to the Setup section of the menu and select Network Update to perform the update. appears on the TV screen. See Network Update (page 119) to update the receiver to a newer software version. Video cannot be output from this jack. If you use the receiver in main zone, connect the receiver to a TV via an HDMI cable. If you connect the receiver to a TV via a video cord, set Playback Resolution to 480i/576i (page 111). If you connect the receiver to a TV via a component video cord, set Playback Resolution to a parameter appropriate to your TV (page 111).
Error messages
You can check the status of the receiver by the message. See the following table to solve the problem. If any problem persists, consult your nearest Sony dealer.
continued
147US
Message list after Auto Calibration measurement

Display Code 31 Code 32 Explanation SPEAKERS (A/B/A+B/OFF) is set to OFF. Set to other speaker settings and reperform the measurement. None of the speakers were detected. Make sure that the plug of the optimizer microphone is inserted all the way inside the AUTO CAL MIC jack, then reperform the Auto Calibration function. None of the front speakers are connected or only one front speaker is connected. The optimizer microphone is not connected. Make sure that the plug of the optimizer microphone is inserted all the way inside the AUTO CAL MIC jack, then reperform the Auto Calibration function. Either the left or right surround speaker is not connected. Surround back speakers are connected even though surround speakers are not meant to be connected. Connect the surround speaker(s) to the SURROUND terminals. The surround back speaker is connected only to the SURROUND BACK (ZONE 2) R terminals. When you connect only one surround back speaker, connect it to the SURROUND BACK (ZONE 2) L terminals. Only one front high speaker is connected. Connect the front high speaker to each of the FRONT B/FRONT HIGH terminals. Front high speakers are connected even though surround speakers are not connected. Connect the surround speaker(s) to the SURROUND terminals. Speakers are not placed in the proper position. Speakers or an optimizer microphone on the right or left may be placed wrongly. See 1: Installing speakers (page 24) and check the speaker position. The measurement process has completed with high noise level detection. You may be able to achieve better results if you try in a quite environment again. The input from the microphone is too big. It may be too close the distance between the speaker and the microphone. Retry the measurement after setting apart from each other. When you use the receiver as a pre-amplifier, either messages may appear, depending on the power amplifier you connect. However, there will be no problems, even if you continue to use the receiver without changes. The distance and position of a subwoofer cannot be detected. Or the angle of the speaker position cannot be detected. This may be caused by noise. Try to perform the measurement in a quiet environment. Measurement has been completed. However the speakers are not placed in the proper position with respect to each other. See 1: Installing speakers (page 24) and check the relative positions of the speakers.
Code 33
Code 34
Warning 40 Warning 41 Warning 42
Warning 43
Warning 44
NO WARNING There is no warning information. ---------No speakers are connected.
148US
Clearing the memory

Reference sections
To clear All memorized settings Memory of the multifunction remote control See page 48 page 135
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 130 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Additional Information Amplifier section
POWER OUTPUT1) 2) Rated Power Output at Stereo Mode (8 ohms 20 Hz 20 kHz, THD 0.09%): 130 W + 130 W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.15%): 130 W + 130 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT: 140 W + 140 W CENTER: 140 W SURROUND: 140 W + 140 W SURROUND BACK: 140 W + 140 W Reference Power Output (4 ohms 1 kHz, THD 0.7%) FRONT: 130 W + 130 W CENTER: 130 W SURROUND: 130 W + 130 W SURROUND BACK: 130 W + 130 W
1)
To clear the memory of the simple remote control

After removing the batteries, do not use the remote control for a few minutes.
Rebooting the receiver

If the buttons on the receiver or the remote control do not work due to a malfunction of the receiver, reboot the receiver. Hold down ?/1 for 10 seconds. When the lamp above ?/1 flashes in green, the reboot starts.
About support information

Refer to the following web site for details of the latest information on the receiver. http://www.sony.com/essupport
Measured under the following conditions: Power requirements: 120 V AC, 60 Hz 2) Depending on the sound field settings and the source, there may be no sound output.
continued
149US
Frequency response3)
PHONO RIAA equalization curve 1.0 dB (20 Hz 20 kHz) 10 Hz 100 kHz 3 dB
AM tuner section
Tuning scale 10 kHz step 9 kHz step Tuning range 530 1,710 kHz 531 1,710 kHz
MULTI CHANNEL INPUT, SA-CD/CD, TAPE, MD, TV, VIDEO 1/2, BD/DVD, SAT/CATV, GAME
3)
Intermediate frequency 450 kHz Antenna (aerial) Loop antenna (aerial)
When 2ch Analog Direct is being used.
Video section
Inputs/Outputs Video: 1 Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms PB: 0.7 Vp-p, 75 ohms PR: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through
Inputs (Analog)
PHONO Sensitivity: 2.5 mV Impedance: 50 kohms S/N: 90 dB (A, 20 kHz LPF) Sensitivity: 150 mV Impedance: 50 kohms S/N: 100 dB (A, 20 kHz LPF)
MULTI CHANNEL INPUT, SA-CD/CD, TAPE, MD, TV, VIDEO 1/2, BD/DVD, SAT/CATV, GAME
HDMI Video
Input/Output (HDMI Repeater block) 640 480p @ 59.94/60 Hz 720 480p @ 59.94/60 Hz 1280 720p @ 59.94/60 Hz 1920 1080i @ 59.94/60 Hz 1920 1080p @ 59.94/60 Hz 720 576p @ 50 Hz 1280 720p @ 50 Hz 1920 1080i @ 50 Hz 1920 1080p @ 50 Hz 1280 720p @ 29.97/30 Hz 1920 1080p @ 29.97/30 Hz 1280 720p @ 23.98/24 Hz 1920 1080p @ 23.98/24 Hz
Inputs (Digital)
IN 1 (BD/DVD), IN 2 (VIDEO 1), IN 3 (SACD/CD) (Coaxial) Impedance: 75 ohms S/N: 96 dB (A, 20 kHz LPF)
IN 1 (GAME), IN 2 S/N: 96 dB (SAT/CATV), IN 3 (TV), (A, 20 kHz LPF) IN 4 (MD) (Optical)
Outputs
TAPE (REC OUT), Voltage:150 mV VIDEO 1, ZONE 2, Impedance: 1 kohm ZONE 3 (AUDIO OUT) FRONT L/R, CENTER, Voltage: 2 V Impedance: 1 kohm SURROUND L/R, SURROUND BACK L/R, FRONT HIGH L/R, SUBWOOFER
HDMI Video (3D)

Input/Output (HDMI Repeater block) 1280 720p @ 59.94/60 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080i @ 59.94/60 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p @ 59.94/60 Hz Side-by-Side (Half) Over-Under (Top-and-Bottom)
FM tuner section
Tuning range 87.5 108.0 MHz Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced
150US
1280 720p @ 50 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080i @ 50 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p @ 50 Hz Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p @ 23.98/24 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1920 1080p @ 29.97/30 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1280 720p @ 23.98/24 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom) 1280 720p @ 29.97/30 Hz Frame Packing Side-by-Side (Half) Over-Under (Top-and-Bottom)
Type of content Music
File format
Extensions
MP3 (MPEG-1 .mp3 Audio Layer III)6) AAC1) 2) 5) 6) .m4a
WMA9 .wma Standard1) 2) 5) 6) LPCM6) FLAC6) Photo JPEG PNG GIF

1) 2) 3) 4)
.wav .flac .jpg, .jpeg, .mpo .png
.gif
5) 6)
Playable types of files

Type of content Video File format Extensions
The receiver does not play coded files such as DRM. The receiver does not play this file format on a DLNA server. The receiver can only play standard definition video on a DLNA server. The receiver plays AVCHD format files that are recorded on a digital video camera, etc. The AVCHD format disc will not play if it has not been correctly finalised. The receiver does not play coded files such as Lossless. Sampling frequency/bit depth supported: up to 192 kHz/24 bit
Notes
Some files may not play depending on the file format, file encoding, recording condition, or DLNA server condition. Some files edited on a computer may not play. The receiver can recognise the following files or folders in USB devices: up to folders in the 3rd tree up to 500 files in a single tree The receiver can recognise the following files or folders stored in the DLNA server: up to folders in the 18th tree up to 999 files in a single tree Some USB devices may not work with this receiver. The receiver can recognise Mass Storage Class (MSC) devices (such as flash memory or an HDD), Still Image Capture Device (SICD) class devices and 101 keyboard (front USB jack only). continued
MPEG-1 Video/ .mpg, .mpeg, PS1) 2) MPEG-2 Video/ .m2ts, .mts PS, TS1) 3) MPEG-4 AVC1) 2) WMV91) 2) AVCHD Xvid
2)
.mkv, .mp4, .m4v, .m2ts, .mts .wmv, .asf

4)
.avi
151US
To avoid data corruption or damage to the USB memory or devices, turn the receiver off when connecting or removing the USB memory or devices. Concerning the formats defined in the DLNA guidelines, the server is required to offer the content to which the format information defined in the DLNA guidelines has been added properly.
General
Power requirements 120 V AC, 60 Hz Power consumption 480 W Power consumption (during standby mode) 0.5 W (When Control for HDMI (page 113), Pass Through (page 113), Network Standby (page 115), and RS232C Control (page 118) are set to OFF, and the power for zone 2/zone 3 is turned off.) Dimensions 430 mm 187.5 mm 420 mm (17 in 7 3/8 in 16 1/2 in) (width/height/depth) including projecting parts and controls Mass (Approx.) 17.7 kg (39 lb 1 oz)
Supplied accessories
Operating Instructions (this manual) Quick Setup Guide (1) Software License Information (1) Optimizer microphone ECM-AC1 (1) FM wire antenna (aerial) (1) AM loop antenna (aerial) (1) AC power cord (mains lead) (1) Multifunction remote control (1) Simple remote control (1) R6 (size-AA) batteries (4) Speaker cord connection tool (1)
Design and specifications are subject to change without notice. Standby power consumption 0.5 W.
152US
Index
Symbols
U SIGNAL GND terminal 44 Center Analog Down Mix 106 Changing the display 126 Clear receiver 48 remote control 135 Connection Server Settings 115 Connections antenna (aerial) 43 audio equipment 39 monitor 28 Network 45 speakers 26 video equipment 30 Control for HDMI 113 Crossover Frequency 105
Numerics
12V Trigger 117 2 channel 71 2ch Analog Direct 71 2ch Stereo (mode) 71 3D Output Settings 112 5.1 channel 24 7.1 channel 24 9.1 channel 24
A
A.F.D. (mode) 72 A/V Sync 108 AC power cord (mains lead) 47 Advanced Auto Volume 77, 107 AM 62 Antenna (aerial) 43 Antenna Aiming 66 Audio Input Assign 88, 114 Audio Out 112 Audio Return Channel (ARC) 86, 88 Audio Settings 107 Auto Calibration 101 Auto Calibration Setup 101 Auto Standby 118 Auto Tuning 62 Automatic Phase Matching 103
D
D.C.A.C. (Digital Cinema Auto Calibration) 101 Decode Priority 108 Digital Legato Linear (D.L.L.) 107 Direct Tuning 62, 67 Display 12, 121 Distance Unit 106 DLNA 57, 61 Dual Mono 107 DVD player 30 Dynamic Range Compressor 108
E
Easy Automation 91 Easy Setup 49, 101 Effect type 73 Equalizer 77, 107 ES Remote 91 External Control 115
Bass 11, 77 Berlin Philharmonic Hall 74 Bi-amplifier connection 97 Blu-ray Disc Player 30
C
Cable box 34 Calibration Type 102 Camcorder 37 Category Mode 66 CD player 39
F
Favorites 53 FM 62 Front Reference Type 102
continued
153US
G
GUI (Graphical User Interface) 28
Music 74 Muting 54
H
H.A.T.S. 113 HD-D.C.S. 72 HD-D.C.S. (Effect type) 73 HDMI Settings 112 Home Theater Control 86
N
Name In 102 Name Input 63 Neo:X (Cinema) 72 Neo:X (Game) 74 Neo:X (Music) 74 Network Settings 115 Network Standby 115 Network Update 119
I
Initialize Personal Information 119 Input Edit 114 INPUT MODE 88 Input Settings 114 Internet content 57 Internet Services Settings 115 Internet Settings 115 Internet video 57 Internet Video Parental Control 116 Internet Video Unrated 116 IP Content Noise Reduction 58 iPhone/iPod 56, 60
O
One-Touch Play 85
P
Parental Control Area Code 115 Parental Control Password 115 Parental Lock 68 Pass Through 87, 113 Phase Audio 106 Phase Noise 105 PHONES 11 Playback Resolution 111 PlayStation 3 32 PLII (Movie) 72 PLII (Music) 74 PLIIx (Movie) 72 PLIIx (Music) 74 PLIIz Height 72, 74, 75 Portable Audio 74 Position 101 PRE OUT 27 Preset channels 67 Preset stations 63 PROTECTOR 147
J
Jazz Club 74
L
L.F.E. (Low Frequency Effect) 13 Language 118 Large 104 Line Out 81, 117 Listen 54 Live Concert 74 Lock Code 69
M
MASTER VOLUME 11 MD deck 42 Menu 52, 98 Messages Auto Calibration 148 Error 147 SIRIUS 70 Movie 72 Multi Zone 78 154US
R
Radio ID 65 Recording 94, 95 Remote control 1720, 48, 127136 Renderer Access Control 115 Renderer Options 115 Resetting receiver 48 remote control 135
Resolution 109 RS232C Control 118
S
Satellite radio 64 Satellite tuner 34 SB Assign 104 Scene Select 86 Screen Format 112 Server Preparing 51 Setting menu 98 Settings 98 Settings Lock 118 Sirius 64 Sirius satellite radio 64 Sleep timer 94 Small 105 Software Update Notification 118 Sound Effects 71 Sound Field 71, 108 Sound Field Mode 75, 108 Sound Optimizer 76, 107 Speaker Connection 104 Speaker impedance 49, 106 Speaker Pair Match 102 Speaker pattern 104 Speaker Relocation 103 Speaker Settings 101 Speaker Setup 104 SPEAKER SHORTED 147 SPEAKERS (A/B/A+B/OFF) 10, 50 Sports 74 Stadium 74 STEREO/MONO 62 Subwoofer Level 112 Subwoofer Low Pass Filter 112 Subwoofer Muting 107 Super Audio CD player 39 System Audio Control 85 System Information 119 System Power-Off 85 System Settings 118 SYSTEM STANDBY 128
Test Tone 105 TONE 11 TONE MODE 11, 48 Treble 11, 77 True Concert Mapping A/B 74, 75 Tuner 62 Tuning 62, 63 Turntable 44 TV Type 112
U
Up converting 22 USB 55 User Reference Edit 102
V
VCR 36 VIDEO 2 IN jacks 37 Video Direct 114 Video Input Assign 88, 114 Video Settings 109 Vocal Height 74
W
WALKMAN 55 Watch 54
Z
Zone Control 116 Zone Resolution 110 Zone Settings 116 Zone Setup 117
T
Tape deck 44 155US

Multi Channel AV Receiver: Operating Instructions

Uploaded by

Copyright:

Available Formats

Multi Channel AV Receiver: Operating Instructions

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Multi Channel AV Receiver: Operating Instructions

Uploaded by

Copyright:

Available Formats

4-287-973-11(2)

Multi Channel AV Receiver

2011 Sony Corporation

For customers in the United States

Important Safety Instructions

Consult the dealer or an experienced radio/TV technician for help.

About This Manual

Main features of the receiver

Better image and sound quality

Feature Sound fields

Enjoying Sound Effects

Using Multi-zone Features Enjoying images/sound

Using Other Features Enjoying an iPhone/iPod

Playing via a Network

Using the Remote Control

Description and location of parts

To remove the cover

To open the cover

Indicators on the display

Used for maintenance and service.

D LAN ports (switching hubs) (page 46)

I SPEAKERS section (page 26)

PRE OUT jacks Connect to an external power amplifier. 16US

Multifunction remote control (RM-AAL040)

Simple remote control (RM-AAU124)

Read the following before you connect any equipment

High quality image

Q: Does your monitor have an HDMI jack?

Connecting the audio equipment

Preparing the receiver and the remote control

Setting the receiver

Setting the audio output settings on the connected equipment

Function for conversion of video signals

HDMI OUT A/B (up to 1080p)

COMPONENT VIDEO MONITOR MONITOR VIDEO OUT OUT (up to 1080i) a* a* a* a*

HDMI IN VIDEO IN COMPONENT VIDEO IN

Note on converting video signals

To connect a recording equipment

To display Closed Caption

Digital audio formats supported by the receiver

Maximum number of channels

Dolby Digital Plus*

DTS-HD High Resolution Audio*

DTS-HD Master Audio*

Multi-Channel Linear PCM*

7.1 channel speaker system using surround back speakers

Examples of speaker system configuration

7.1 channel speaker system using front high speakers

9.1 channel speaker system

5.1 channel speaker system

Recommended speaker placement

6.1 channel speaker system

FRONT B/FRONT HIGH terminals 1)

A Monaural audio cord (not supplied) B Speaker cords (not supplied)

Loosen Tighten Speaker cord connection tool

To enable 9.1 channel playback

2: Connecting the monitor

TV monitor without an HDMI jack

3: Connecting the video equipment