Mathews Roller Conveyors

Chain Driven Live Roller Conveyor
HB-828 - 12/03
To contact FKI Logistex, Automation Division: For service: Customer Service and Support Group (CSSG) Hotline 1-800-992-1267 On the World Wide Web: www.fkilogistex.com/automation By mail: FKI Logistex, Automation Division 10045 International Boulevard Cincinnati, Ohio 45246 (513) 874-0788
The information presented in this document is correct at the time of publication. FKI Logistex Automation Division has made every effort to ensure that the information presented is correct and free from error. However, some errors or misprints may occur. Please contact FKI Logistex, Automation Division with any corrections. This document is copyrighted 2001 by FKI Logistex, Automation Division, all rights reserved. No Part of this Users Guide may be reproduced and/or distributed to parties other than the customer and the customers employees for whom it was originally produced.
Direct questions and comments concerning the information contained in this manual to:
[email protected] or Product Management FKI Logistex, Automation Division 10045 International Boulevard Cincinnati, Ohio 45246 (513) 874-0788
HB-828 - 12/03
Table of Contents
Engineering Data Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 Single Strand CDLR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Product Width - Straight Conveyor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Product Width - Curves - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Effective Conveying Widths for C557 Single Strand Chain Driven Live Roller Curve: - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Product Length - Straight Conveyor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Product Length - Curves - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Product Weight - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Product Loading - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Chain Pull Calculations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Live Load (A) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Dead Load (B) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Chain Pull (C) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Inclines (D) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Deflectors (E) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Effective Chain Pull - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Total Chain Pull (C + D + E) x 1.25 = Eff. Chain Pull (lbs.)- - - - - - - - - - - - - - - Horsepower Calculations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 2 3 3 3 4 4 5 5 5 6 6 6 6 7 7
Chain Pull and Horsepower Calculations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Roller to Roller CDLR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8 Product Width - Straight Conveyor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8 Product Width - Curves - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8 Product Length - Straight Conveyor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9 Product Length - Curves - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9 Product Weight - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -10 Product Loading - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -11 Chain Pull and Horsepower Calculations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12 Chain Pull Calculations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12 Horsepower Calculations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -13 Dead Loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -14 Service Factors - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -16 Single Strand CDLR Units - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -17 Intermediate Drive - Model LRSS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -17 End Drive - Model LRSC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19 Components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -21 C571 Intermediate Drive - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -21 C573 End Drive - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -23 C559 End Drive - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -25 C127 End Section - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -26 C572 Intermediate Tread Sections - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -27 C557 Curve - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -28 C546 - 30 Spur - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -32 C547 - Power Crossover Section - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -34
HB-828 - 12/03 TOC - 1
Table of Contents
Roller To Roller CDLR Units - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -35 Model RRCD190 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -35 Model RRCD250 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -37 Model TTRC250 True Tapered Curve - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -39 Model RRCD256 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -41 Model RRCD350 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -43 Components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -45 C20002/C20003 Intermediate Drive Section (1.90 dia. Rollers) - - - - - - - - - - - - - -45 C20000 Intermediate Tread Section (1.90 dia. Rollers) - - - - - - - - - - - - - - - - - - -47 C20004 Straight Faced Roller Curve (1.90 dia. Rollers) - - - - - - - - - - - - - - - - - - -49 C20001 Chain Crossover (1.90 dia. Roller) - - - - - - - - - - - - - - - - - - - - - - - - - - - -51 C20014 Intermediate Drive Section (2.50 dia. Rollers) - - - - - - - - - - - - - - - - - - - -52 C20014/C20016 Intermediate Drive Section (2.50 dia. Rollers) - - - - - - - - - - - - - -53 C20010 Intermediate Tread Section (2.50 dia. Rollers) - - - - - - - - - - - - - - - - - - -54 C20018 Straight Faced Roller Curve (2.50 dia. Rollers) - - - - - - - - - - - - - - - - - - -57 C20013 Chain Crossover (2.50 dia. Roller) - - - - - - - - - - - - - - - - - - - - - - - - - - - -60 C20024 Intermediate Drive Section (2.56 dia. Rollers) - - - - - - - - - - - - - - - - - - - -61 C20024/C20026 Intermediate Drive Section (2.56 dia. Rollers) - - - - - - - - - - - - - -62 C20020 Intermediate Tread Section (2.56 dia. Rollers) - - - - - - - - - - - - - - - - - - -63 C20028 Straight Faced Roller Curve (2.56 dia. Rollers) - - - - - - - - - - - - - - - - - - -65 C20023 Chain Crossover (2.56 dia. Roller) - - - - - - - - - - - - - - - - - - - - - - - - - - - -67 C20036 Intermediate Drive Section (3.50 dia. Rollers) - - - - - - - - - - - - - - - - - - - -68 C20036/C20037 Intermediate Drive Section (3.50 dia. Rollers) - - - - - - - - - - - - - -69 C20030 Intermediate Tread Section (3.50 dia. Rollers) - - - - - - - - - - - - - - - - - - -70 C20052 Straight Faced Roller Curve (3.50 dia. Rollers) - - - - - - - - - - - - - - - - - - -73 C20033 Chain Crossover (3.50 dia. Roller) - - - - - - - - - - - - - - - - - - - - - - - - - - - -75 General Specifications Roller to Roller Chain Driven Live Roller Conveyor - Available as a Standard Product - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -77 Roller to Roller Chain Driven Live Roller Conveyor - Available as an Engineered Product - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -78 Chain Driven Live Roller Conveyor Units - Approximate Weight Per Foot - - - - - - -79 Controlled Flow Conveyor Application DatCFC Series II, III and IV - Available as an Engineered Product - - - - - -81 How CFC Series II, III and IV Accumulation Operates - - - - - - - - - - - - - - - - - - - - -81 Release Modes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -81 Singulation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -81 Sequential - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -81 Application Information - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -82 Units - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -83 CFC Series II - (1.90 dia. Rollers) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -83 Conveyor Capacity Calculations (CFC II)- - - - - - - - - - - - - - - - - - - - - - - - - - - -85 Heavy Duty CFC Series III - (2.50 dia. Rollers) - - - - - - - - - - - - - - - - - - - - - - - - -86 Conveyor Capacity Calculations (CFC III) - - - - - - - - - - - - - - - - - - - - - - - - - - -88 Extra Heavy Duty CFC Series IV - (3.50 dia. Rollers) - - - - - - - - - - - - - - - - - - - - -89 Conveyor Capacity Calculations (CFC IV) - - - - - - - - - - - - - - - - - - - - - - - - - - -91
TOC - 2 HB-828 - 12/03
Table of Contents
Components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -92 CFC Series II - Drive Section (1.90 dia. Rollers) - - - - - - - - - - - - - - - - - - - - - - - -92 CFC Series II - Intermediate Conveyor Section (1.90 dia. Rollers) - - - - - - - - - - - -94 Heavy Duty CFC Series III - Drive Section (2.50 dia. Rollers) - - - - - - - - - - - - - - -96 Heavy Duty CFC Series III - Intermediate Conveyor Section (2.50 dia. Rollers) - -98 Extra Heavy Duty CFC Series IV - Drive Section (3.50 dia. Rollers) - - - - - - - - - - 100 Extra Heavy Duty CFC Series IV - Intermediate Conveyor Section (3.50 dia. Rollers) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 102 Supports C1230 Floor Single Leg Floor Support - 750 Pound Capacity - - - - - - - - - - - - - - - 103 C1231 Floor Support - 1500 Pound Capacity - - - - - - - - - - - - - - - - - - - - - - - - - - 103 C681, C682, C683 and C684 Series - 3000 Pound Capacity Floor Supports - - - -106 C698 and C699 Series - 6000 pound capacity Floor Supports - - - - - - - - - - - - - - 109 C1570 - Floor Support - 12,000 or 25,000 Pound Capacity (Formerly E-609) - - - 111 C1275 - Hanger Support - 1500 Pound Capacity - - - - - - - - - - - - - - - - - - - - - - - 112 For use with Single Strand Chain Driven Live Roller Conveyor - - - - - - - - - - - 112 Accessories Model 3500TT - 90 Powered Turntable - 3000 Pound Capacity - - - - - - - - - - - -115 Model 3000XF - Two Strand Chain Transfer - 3000 Pounds Capacity - - - - - - - - - 116 For use with RRCD250 and RRCD256 CDLR - - - - - - - - - - - - - - - - - - - - - - - 116 Model 3100XF - Two Strand Chain Transfer - 3000 Pounds Capacity - - - - - - - - - 118 For use with RRCD250 and RRCD256 CDLR - - - - - - - - - - - - - - - - - - - - - - - 118 D1443 - Angle Guard Rail - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 120 For use with Single Strand Chain Driven Live Roller Conveyor - - - - - - - - - - - 120 D1444 - Curved Angle Guard Rail - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 121 For use with C557 Curves - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 121 Electrical Components & Control Equipment Combination Starters - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 123 Components For Driving and Controlling the Powered Conveyors - - - - - - - - - - - - - - 125 Motors - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 125 Gear Reducer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 126 Brakes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 127 Clutch Brake - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 127 Motor Starters - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 127 Manual Motor Starters - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 127 Magnetic Motor Starters- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -127 Combination Magnetic Motor Starters and Control Panels- - - - - - - - - - - - - - - 128 Electrical Enclosures - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 129 Switching Devices - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 129 Push Buttons - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -129 Limit Switches- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 129 Selector Switches - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 129 Photoelectric Relays - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 129 Solenoid Valves - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 130 Air Controls - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 130
HB-828 - 12/03
TOC - 3
Table of Contents
TOC - 4
HB-828 - 12/03
Engineering Data
Engineering Data
Introduction
This manual starts with the assumption that you have already determined which type of Mathews chain driven live roller conveyor you require. A chain driven live roller conveyor is a conveyor where the product rides directly on the carrying rollers. These carrying rollers have sprockets welded to them, which in turn are powered by a chain. This manual will explain the various types of Mathews chain driven live roller conveyors manufactured by Mathews. In this manual we will describe the following types of chain driven live roller conveyors: 1. Single Strand Chain Driven Live Roller 2. Roller to Roller Chain Driven Live Roller In this manual, you will note that we are depicting standard units, illustrating the components from which they are assembled, as well as offering a description of these various components. Also included are descriptions of supports and accessories for each type of conveyor. Due to the physical design of the chain driven live roller, we will be referring to two different types of conveyor width. These are Effective Conveying Width and the Between Frames Dimension. See the drawing below: For the various sizes of CDLR, the width of the chain box will also vary and the effective conveying surface will always be less than the between frames dimension. When selecting equipment, be sure this aspect has been considered. In order to properly evaluate chain driven live roller, we will break it down into the two types, single strand chain driven live roller and roller to roller chain driven live roller.
HB-828 - 12/03
Engineering Data - 1
Engineering Data
Single Strand CDLR

As the name implies, it consists of a single strand of chain traveling over sprockets welded to the rollers. There is only one sprocket per roller. Contact with the sprocket teeth is maintained by a continuous cover plate and hold down. The chain is also returned in this chain box. Because of limited tooth engagement, this type of CDLR should not be used for start-stop applications and only with moderate unit loads. There are several product features that will determine the conveyor specifications:
Product Width - Straight Conveyor

The effective conveyor width should be approximately 3" wider than the widest product to be conveyed, then select the next larger standard width conveyor. For single strand chain driven live roller, our standard effective conveying widths are 15", 21", 27", 33 and 39. In the single strand CDLR, the between frames dimension is always effective conveying width + 2". Example: 23" wide product + 3" = 26" Next larger standard is 27" Effective Conveying Width or 29" Between Frames
Product Width - Curves

Many times curves in a system will dictate the width of the conveyor for the entire system, in that the product may require additional space to negotiate the turn. This additional space depends upon the width and length of the product. The chart below shows the conveyor widths required to convey product around a curve. The conveyor widths are listed based on our standard radii for the various standard Between Frame dimensioned curves. This chart is also based on the formula listed and good conveyor practice, that the inside radius should be greater than the length of the product. Formula for determining distance Between Frames or Guard Rails. G = ( Radius + PackageWidth ) 2 + PackageLength 2 ( Radius 2 ) 2
HB-828 - 12/03
Engineering Data
Effective Conveying Widths for C557 Single Strand Chain Driven Live Roller Curve:
Product Width 9 15 15 15 15 21 12 15 21 21 21 21 15 21 21 21 21 21 18 21 21 27 27 27 21 27 27 27 27 27 24 27 27 33 33 33 27 33 33 33 33 33 30 33 33 33 39 39 33 39 39 39 39 39 36 39 39 39 ----Effective Conveying Width
Product Length 15 21 27 33 39
Product Length - Straight Conveyor

It is good practice, for chain driven live roller conveyors to have a minimum of three rollers under the product at all times. To determine roller spacing, take the length of the shortest product, divide by 3 and choose the standard roller spacing required, either 4-1/2" or 6" centers. 21 long product - = 7.0 Example: -------------------------------------------3 Rollers The closest standard roller spacing is 6"centers.
Product Length - Curves

On curves, the roller centers on the inside rail are closer together than they are on the outside rail. In our standard construction, the wider the conveyor, the more rollers are required in the curve to keep the roller centers to a minimum. You must keep this fanning effect in mind when choosing curves. The following chart shows the roller spacing at various points on the curve. C557 Single Strand Curve Between Frames Dimension 17 23 29 35 41 *Effective Conveying Width Effective Conveyor Width 15 21 27 33 39 Rollers Centers At *Inside Rail 3.17 3.13 3.10 3.09 3.07 *Center-Line 3.83 3.82 3.81 3.81 3.80 Outside Rail 4.48 4.50 4.52 4.53 4.54
HB-828 - 12/03
Engineering Data
Product Weight
A check should be made concerning the product weight by taking the various product weights divided by 2/3 of the number of rollers under the product and compare the capacity per roller for that width. 1.90 Dia. x .148 Steel Roller Between Frames Dimension 17 23 29 35 41 Effective Conveyor Width 15 21 27 33 39 Roller Weight w/o Axles 4.1# 5.4# 6.8# 8.2# 9.5# Roller Capacity w/B1020 Bearing 310 310# 310# 290# 254#
Also note that the frame capacity for single strand CDLR is 100 pounds per foot.
Product Loading
The maximum load that the conveyor will encounter (live load) is a major factor in determining the drive and motor requirements. The conveyor loading, expressed in pounds per foot, can be obtained by any of the following methods. 1. Divide the total maximum load on the conveyor by the conveyor length. T otal load on conveyor ( lbs ) -------------------------------------------------------------------------------- = Conveyor Loading ( lbs ft ) Conveyor Length ( ft ) 2. When the product is introduced to the conveyor at a given rate, the conveyor loading is a function of product weight, product rate, and conveyor speed. P rod Wt ( lbs ) Prod Rate ( ctns min ) ------------------------------------------------------------------------------------------------------------ = Conveyor Loading ( lbs ft ) Conveyor Speed ( ft min ) 3. When the product is back to back on the conveyor, the conveyor loading is a function of product weight and product length. P rod uct Weight ( lbs ) ------------------------------------------------------------ = Conveyor Loading ( lbs ft ) Product Length ( ft ) 4. When the product is introduced to the conveyor at an uneven rate, the conveyor loading can be determined by taking the maximum weight that the conveyor must handle in one minute and dividing by the conveyor speed. Product Weight ( lbs min ) --------------------------------------------------------------------------- = Conveyor Loading ( lbs ft ) Conveyor Speed ( ft min ) Always consider the worst loading condition that the conveyor will be subject to in order to determine conveyor loading. In order to determine actual chain pull and HP requirements, use the following procedure.
HB-828 - 12/03
Engineering Data
Chain Pull and Horsepower Calculations

Chain Pull Calculations Live Load (A)
The total weight of the product being conveyed is normally expressed in pounds per foot (lbs./ft.). For various formulas to determine loading see Product Loading section. Live Load (lbs./ft.) x Conveyor Length = Total Live Load (lbs.)
Dead Load (B)

When power is applied to a chain driven live roller conveyor, all carrying rollers are turning and therefore must be included in our calculations. On chain driven live roller conveyor, this weight can be substantial. This dead load is a combination of two parts. 1. The first part is the weight of all rollers, chain and sprockets and is expressed in lbs./ft. This weight has been calculated for you for the various roller centers and widths of single strand chain driven live roller conveyor. Dead Load (Part 1) x Conveyor Length = DL1 (lbs.) 2. The second part is the weight of all drive pulleys and end rollers and is expressed in lbs. This weight has been calculated for you for the various widths and types of live roller conveyor. This weight is constant and is not dependent on conveyor length. Dead Load (Part 2) = DL2 (lbs.) DEAD LOADS Single Strand Chain Driven Live Roller Carrying Roller Centers Part 1 4-1/2 6 C573 End Drive Part 2 C571 Int. Drive C127 End Unit C557 90 Curve w/Drive and End Unit 17 W lbs./ft. 15.5 10.8 23.3# 71.1# 8.4# 60# 23 W lbs./ft. 19.6 13.6 24.6# 86.6# 11.2# 100# 29 W lbs./ft. 23.6 16.4 26.9# 102.0# 13.5# 150# 35 W lbs./ft. 27.8 19.2 29.2# 117.5# 15.8# 210# 41 W lbs./ft. 31.9 21.8 31.5# 132.9# 18.1# 280#
Note: Select (1) one of C573 End Drive and (1) one C127 End Unit or (1) one C571 Intermediate Drive and (2) two C127 End Unit and Curve quantity (if required). Dead Load2 (DL2) = Total Dead Load of Drive and End Unit(s) + Dead Load of Curves (if required) = Dead Load (Part 2) = DL2(lbs.) DL1 + DL2 = B (Total Dead Load)
HB-828 - 12/03
Engineering Data
Chain Pull (C)

Chain pull is the force required to start and maintain the movement of all rollers and live load and is obtained by multiplying the total live load plus dead load by the coefficient of friction, which varies with the type of conveyor. Coefficient of Friction Single Strand CDLR Roller to Roller CLR (A + B) x Coefficient of Friction = C (Chain Pull in lbs.) .06 .05
Inclines (D)
The maximum recommended incline for chain driven live roller conveyor is 5 degrees. It is advisable to conduct a test to insure a particular product will convey on an inclined unit. Additional chain pull is generated by elevating the product and can be calculated two ways. 1. Total Live Load on Incline (lbs.) x Sine of Angle = Additional Belt Pull (lbs.) 2. The second method can be used for uniformly loaded conveyors. Average Live Load (lbs./ft.) x Rise in Elevation (ft.) = Additional Belt Pull (lbs.) The increase in chain pull generated by an incline is not affected by the coefficient of friction.
Sines of Various Angles Angle 1 2 3 4 5 Sine .02 .04 .05 .07 .09
Deflectors (E)
Deflectors add to the chain pull due to the force required to slide the products off the conveyor. For each deflector add 30% of the weight of the heaviest product being deflected, to the chain pull. Number of Deflectors x Heaviest Product (lbs.) x .30 = Additional Chain Pull (lbs.)
Effective Chain Pull

For effective chain pull add 25% to the total chain pull for chain flexing and bearing friction losses.
HB-828 - 12/03
Engineering Data
Total Chain Pull (C + D + E) x 1.25 = Eff. Chain Pull (lbs.)

After having determined the effective chain pull, you should check that figure against the chart below, which shows allowable chain pull, to make sure you are not exceeding the capacity of the chain. If you do exceed the capacity, you need to shorten the conveyor or decrease the live load. MAXIMUM ALLOWABLE CHAIN PULL (LBS.) Chain No. 40 50 60 80 100 Conveyor Speed (FPM) 0 - 60 560# 875# 1200# 2100# 3550# 80 500# 800# 1075# 1950# 3250#
Note: At higher speeds, noise level may be a consideration.
Horsepower Calculations
The required drive horsepower may be calculated as follows: Effective Chain Pull ( lbs ) x Conveyor Speed ( FPM ) ------------------------------------------------------------------------------------------------------------------------------------------------ = HP 33,000 Reducers have inherent inefficiencies, due to design. These inefficiencies vary and the output horsepower from the reducer is less than the input horsepower of the motor. Use the Horsepower calculation and select the next highest standard horsepower motor for the RPM output required from the Horsepower chart. MOTOR / REDUCER HORSEPOWER OUTPUT Motor HP 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 Reducer RPM Output 20 --.30 .59 .79 1.19 1.58 2.58 4.07 29 --.30 .63 .84 1.25 1.67 2.50 3.10 44 --.33 .52 .69 1.29 1.72 2.18 4.33 58 --.35 .53 .76 1.30 1.77 2.18 4.01 68 .18 .23 .38 .57 .81 1.22 1.81 2.27 4.10 88 --.39 .58 .78 1.26 1.82 2.53 4.25 97 --.40 .59 .79 1.28 1.70 2.35 4.08 117 --.39 .62 .85 1.28 1.72 2.59 4.37
HB-828 - 12/03
Engineering Data
Roller to Roller CDLR

With this construction, two plate or A type sprockets are welded to one end of each roller and individual loops of chain connect pairs of rollers in a staggered pattern, along the length of the conveyor. This driving arrangement is more desirable for heavy loads and for applications requiring frequent stopping or reversing service. There are several product features that will determine the conveyor specifications:
Product Width - Straight Conveyor

The effective conveyor width should be approximately 3" wider than the widest product to be conveyed, then select the next larger standard width conveyor. For roller to roller chain driven live roller conveyor, the standard effective widths vary depending upon the size of equipment required. Standard effective conveying widths and between frames dimensions are shown in this manual. As stated earlier, due to the physical design of chain driven live roller, we will be referring to two different types of conveyor width. These are the Effective Conveying Width and the Between Frames dimension. See the drawing below: For the various sizes of CDLR, the width of the chain box will also vary and the effective conveying surface will always be less than the between frames dimension. When selecting equipment, be sure this aspect has been considered.
Product Width - Curves

Many times curves in a system will dictate the width of the conveyor for the entire system, in that the product may require additional space to negotiate the turn. This additional space depends upon the width and length of the product being conveyed, as well as the inside radius of the curve. When selecting the curve, it must be remembered that a curve that utilizes 1.90" dia. rollers cannot be used in conjunction with or driven by a straight section utilizing a 2.50" dia. roller or any other size. The design and dimensions are not compatible. The design of our roller to roller chain driven live roller curves are developed to simplify manufacturing procedures and therefore the outside radius is fixed or constant on each of the three styles of CDLR. As the conveyor width increases, the inside radius decreases. In order to determine the W and/or radius, select the appropriate style of straight section and then, through a trial and error method, use the following formula, plugging in the appropriate numbers until the formula is satisfied. As a general rule, the inside radius of the curve should be greater than the length of the product.
HB-828 - 12/03
Engineering Data
G =
( Radius + Package Width )
Package Length --------------------------------------------- ( Radius 2 ) + 2
Example: Product size - 24" Square Plywood Pallet Weighing 500 lbs. The weight would put it into the 1.90" dia. roller category and in consideration of product width characteristics for straight conveyor, the approximate effective width would be 24" + 3" = 27". Reviewing the specifications for 1.90" dia. CDLR, the closest standard effective width would be 26-3/4" with a between frames dimension of 30". With this in mind, the constant outside radius for the 1.90" dia. roller style CDLR is 65-1/8". 65-1/8 - 30 = Inside Radius of 35-1/8. Using the above formula G ( Eff Width ) = = = = ( 35.125 + 24 ) 2 + 24 2 ( 35.125 2 ) 2
( 59.125 ) 2 + ( 12 ) 2 33.125 3496 + 144 33.1 3640 33.1
= 60.3 33.1 = 27.2 Our initial assumption was correct. If it were not, we would probably check out the next larger standard width unit.
Product Length - Straight Conveyor

It is good practice, for chain driven live roller conveyors to have a minimum of three rollers under the product at all times. To determine roller spacing, take the length of the shortest product, divide by 3 and choose the standard roller spacing required. The standard roller spacing varies depending on the frame and roller size selected. See the individual specification pages for each type in this manual.
Product Length - Curves

On curves, the roller centers on the inside rail are closer together than they are on the outside rail. Due to our design, since the outside radius is fixed or constant on each of the three styles of CDLR, the roller centers on the outside rail are also constant for each style. See the individual specification pages for each type in this manual.
HB-828 - 12/03
Engineering Data
Product Weight
1. Roller Selection and Spacing: Many products have rigid bottoms or conveying surfaces and more often than not they are not exactly flat. This is especially true when dealing with CDLR, since it is probably handling heavier products, which require more rigid containers. In order to compensate for this, it is advisable to figure that only 2/3 of the rollers will support the full weight of the product. Therefore, it is necessary to take the weights of the various products being conveyed and divide by 2/3 of the rollers under the product to determine the required capacity of the roller. Example: 19" long product weighing 80 lbs. 19 long product ---------------------------------------------- = 6.33 roller centers 3 Rollers The closest standard will probably be 6". Therefore, there are three rollers under the product, 2/3 x 3 = 2 roller supporting 80 lbs. 80 lbs. 2 rollers = 40 lbs. per roller required capacity. If you are not able to find a roller with the required capacity, it may be necessary to provide rollers on closer centers. Always consider the worst loading condition that the conveyor will be subject to in order to determine roller spacing. 1.90 Dia. x .109 Steel Roller Between Frames Dimension 18 21 24 27 30 33 36 39 Roller Capacity w/B1020 Bearing 310# 310# 310# 310# 310# 304# 286# 269# 2.50 Dia. x .120 Steel Roller Between Frames Dimension 18 24 30 36 42 48 54 60 Roller Capacity w/B1060 Bearing 610# 610# 610# 610# 610# 596# 591# 555#
2.56 Dia. x .180 Steel Roller Between Frames Dimension 18 24 30 36 42 48 54 60 Roller Capacity w/B1060 Bearing 610# 610# 610# 610# 610# 589# 583# 546#
3.50 Dia. x .300 Steel Roller Between Frames Dimension 18 24 30 36 42 48 54 60 66 72 Roller Capacity w/B1080 Bearing 2500# 2500# 2500# 2500# 2500# 2473# 2443# 2432# 2309# 2100# HB-828 - 12/03
Engineering Data
2. Frame Selection: In order to simplify selection, roller and frame combinations have been selected that offer compatibility in size and capacity. Having determined the roller size, you will find that roller in a specific frame and you will need to confirm that this frame has the required capacity. You need to determine the total load on the conveyor at the worst loading condition and check the frame capacity chart on pages H-27, H-33, H-39, or H-45 depending on the different roller series CDLR. The frame must be able to support the combined weight of the rollers/axles, the live load and any other devices which are to be mounted. 3. Support Selection: You will note that the capacities for the frames are based on support centers either 5'-0" or 10'-0". In some instances, it may be more economical to stay with a smaller roller and increase the number of supports to achieve the desired capacity. When selecting the supports, be sure to include the weight of the frame plus rollers, along with the live load for capacity ratings of the supports. Note that the nominal height is to the bottom of the conveyor frame rail.
Product Loading
The maximum load that the conveyor will encounter (live load) is a major factor in determining the drive and motor requirements. The conveyor loading, expressed in pounds per foot, can be obtained by any of the following methods: 1. Divide the total maximum load on the conveyor by the conveyor length. T otal load on conveyor ( lbs ) -------------------------------------------------------------------------------- = Conveyor Loading ( lbs ft ) Conveyor Length ( ft ) 2. When the product is introduced to the conveyor at a given rate, the conveyor loading is a function of product weight, product rate, and conveyor speed. P rod Wt ( lbs ctn ) Prod Rate ( ctns min ) ----------------------------------------------------------------------------------------------------------------------- = Conveyor Loading ( lbs ft ) Conveyor Speed ( ft min ) 3. When the product is back to back on the conveyor, the conveyor loading is a function of product weight and product length. Product Weight ( lbs ) ---------------------------------------------------------- = Conveyor Loading ( lbs ft ) Product Length ( ft ) 4. When the product is introduced to the conveyor at an uneven rate, the conveyor loading can be determined by taking the maximum weight that the conveyor must handle in one minute and divide by the conveyor speed. Product Weight ( lbs min ) -------------------------------------------------------------------------- = Conveyor Loading ( lbs ft ) Conveyor Speed ( ft min ) Always consider the worst loading condition that the conveyor will be subject to in order to determine conveyor loading. In order to determine actual chain pull and HP requirements, use the following procedure.
HB-828 - 12/03
Engineering Data
Chain Pull and Horsepower Calculations

Dr Ds L L1 L2 Fr Fc Fc1 Fc2 i n n1 n2 P FPM W Diameter of drive rollers (inches) Pitch diameter of sprockets on driven rollers (inches) Conveyor length (feet) Conveyor length upstream of drive (feet) Conveyor length downstream of drive (feet) Rolling resistance, generally accepted @ 5% = 0.05 (1 + i)n 1 Exponential chain loss factor = ---------------------------nx i ( 1 + i)n1 1 Exponential chain loss factor (upstream = ------------------------------n1x i ( 1 + i) n2 1 Exponential chain loss factor (downstream) = ------------------------------n2x i Roller chain loss factor Total number of driven rollers Number if driven rollers (upstream) Number of driven rollers (downstream) Chain pull (lb) Conveyor speed (fpm) Weight per foot (live load + dead load)
Chain Pull Calculations

Calculate the drive chain pull per the following formulas: L x W x Dr x Fr x Fc End Drive: P = -------------------------------------------------Ds W x Dr x Fr - x ( L 1 x Fc 1 + L 2 x Fc 2 ) Center Drive: P = ---------------------------Ds Roller chain loss factor i will vary between 1% and 3% depending on service conditions. Use 1% for ideal conditions with well lubricated chain. Use 1.5% to 3% if operating conditions are severe and if proper chain lubrication and maintenance are not likely. The drive and roller-to-roller chain pulls must be less than the working strengths of the chains. If the drive is located in the center of the conveyor, the drive pull will be twice the roller-to-roller chain pull. Locating the drive chain in the center minimizes the exponential losses in the chain loops. If the drive is located at the end of the conveyor, the drive chain pull will equal the roller-to-roller chain pull and the losses will be maximized. Assumptions: 1. The total live load is uniformly distributed on all the rollers. 2. The load is imposed on each bearing by the driving chains is negligible except for the roller or rollers coupled to the drive.
HB-828 - 12/03
Engineering Data
3. The pull required to turn each roller results from a combined rolling resistance between the roller and bearing and roller and load. 4. The chain transmission factor is constant. 5. The conveyor is horizontal and level. 6. Loads are not rubbing guard rails or chain box.
Horsepower Calculations
The required drive horsepower may be calculated as follows: P x FPMx Ds HP = ----------------------------------- = Output Horsepower Required 33, 000 x Dr Output Horsepower Required Input MotorHP = ----------------------------------------------------------------------------------ReducerEfficency Note: Reducer Efficiency, consult reducer manufacturers efficiency tables. Example: 54 W x 70 foot long 2.50" RRCDLR, 45 FPM with drive located 30 feet from discharge end, 6" roller centers, 250 lbs./ft. live load, chain loss factor i = 1%, pitch diameter of 60A16 roller sprocket, Ds = 3.844", rolling resistance Fr = 5%. ( 1 + 0.01 ) 80 1 L 1 = 40 ft n 1 = 80 Fc 1 = ----------------------------------------- = 152 80 x 0.01 ( 1 + 0.01 ) 60 1 - = 1.36 L 2 = 30 ft n 2 = 60 Fc 1 = -----------------------------------------60 x 0.01 Dead Load is given in the table on the next page as 41.1 lb./ft. W = 250 + 41.1 = 291.1 lb./ft. P x 2.5 x 0.05 ---------------------------------------- x [ 40 x 152 + ( 30 x 136 ) ] = 962 lbs = 2911 3.844
962 < 1000 lb. maximum pull for #60 chain i.e. chain size is OK. 962 x 45 x 3844 H P = ----------------------------------------- = 2.02 Output HP required 33, 000 x 2.5 If reducer efficiency = 0.7, then 2.02 - = 2.88 use 3 HP Motor HP = ---------0.7
HB-828 - 12/03
Engineering Data
Dead Loads
Roller to Roller Chain Driven Live Roller Conveyor 1.90 Dia. Roller Carrying Roller Centers 4 6 8 18 W lbs./ft. 15.3 10.5 8.1 21 W lbs./ft. 16.9 11.5 8.9 24 W lbs./ft. 18.5 12.6 9.6 27 W lbs./ft. 20.0 13.6 10.4 30 W l bs./ft. 21.6 14.7 11.2 33 W lbs./ft. 23.2 15.7 12.0 36 W lbs./ft. 24.7 16.8 12.8 39 W lbs./ft. 26.3 17.8 13.6
Roller to Roller Chain Driven Live Roller Conveyor 2.50 Dia. Roller Carrying Roller Centers 4-1/2 6 7-1/2 9 18 W lbs./ft. 29.7 22.8 18.7 15.9 24 W lbs./ft. 33.8 25.8 21.1 17.9 30 W lbs./ft. 37.8 28.9 23.5 20.0 36 W lbs./ft. 41.9 31.9 26.0 22.0 42 W lbs./ft. 46.0 35.0 28.4 24.0 48 W lbs./ft. 50.0 38.0 30.8 26.1 54 W lbs./ft. 54.1 41.1 33.3 28.1 60 W lbs./ft. 58.1 44.1 35.7 30.1
Roller to Roller Chain Driven Live Roller Conveyor 2.563 Dia. Roller Carrying Roller Centers 4-1/2 6 7-1/2 9 18 W lbs./ft. 36.2 27.7 22.5 19.1 24 W lbs./ft. 42.5 32.4 26.4 22.3 30 W lbs./ft. 48.9 37.2 30.2 25.5 36 W lbs./ft. 55.2 42.0 34.0 28.7 42 W lbs./ft. 61.6 46.7 37.8 31.8 48 W lbs./ft. 67.9 51.5 41.6 35.0 54 W lbs./ft. 74.3 56.2 45.4 38.2 60 W lbs./ft. 80.6 61.0 49.2 41.4
Roller to Roller Chain Driven Live Roller Conveyor 3.50 Dia. Roller Carrying 18 W Roller lbs./ft. Centers 6 9 12 47.3 32.2 24.7 24 W lbs./ft. 57.6 39.1 29.8 30 W lbs./ft. 67.8 45.9 34.9 36 W lbs./ft. 78.1 52.7 40.1 42 W lbs./ft. 88.3 59.6 45.2 48 W lbs./ft. 98.6 66.4 50.3 54 W lbs./ft. 108.8 73.2 55.4 60 W lbs./ft. 119.1 80.1 60.6 66 W lbs./ft. 129.3 86.9 65.7 72 W lbs./ft. 139.5 93.7 70.8
HB-828 - 12/03
Engineering Data
Reducers have inherent inefficiencies due to design. These inefficiencies vary and the output horsepower from the reducer is less than the input horsepower of the motor. Use the Horsepower calculation and select the next highest standard horsepower motor for the RPM output required from the Horsepower chart. Typical Worm Gear / Reducer Horsepower Output Motor HP 1/2 3/4 1 1-1/2 2 3 5 Reducer RPM Output 22 .30 .59 .79 1.19 1.58 2.58 4.07 29 .30 .63 .84 1.25 1.67 2.50 3.10 43 .33 .52 .69 1.29 1.72 2.18 4.33 58 .35 .53 .76 1.30 1.72 2.18 4.01 69 .38 .57 .81 1.22 1.81 2.27 4.10 86 .39 .58 .78 1.26 1.82 2.53 4.25 99 .40 .59 .79 1.28 1.70 2.35 4.08 115 .39 .62 .85 1.28 1.72 2.59 4.37
After having determined the chain pull, you should check that figure against the chart below, which shows allowable chain pull, to make sure you are not exceeding the capacity of the chain. If you have exceeded the capacity, you need to upgrade to a larger chain size (if available as standard), shorten the conveyor, or decrease the live load. Maximum Allowable Chain Pull (lbs.) Chain No. 40 50 60 80 Conveyor Speed (FPM) 0 - 60 560# 875# 1200# 2100# *80 500# 800# 1075# 1950# **100 450# 750# 1000#
*Suggested Maximum Speed for Continuous Strand **Suggested Maximum Speed for Roller to Roller Note: At higher speeds, noise level may be a consideration.
HB-828 - 12/03
Engineering Data
Service Factors
Use the chart below to apply service factors. Reducers must be sized to accept the input motor HP and upgraded by the desired service factor(s). Likewise, service factors must be applied to the chain pull. The allowable chain pull is divided by the appropriate service factors. Service Factor 8 - 10 Hours/Day .8 1.0 1.2 1.2 1.2 1.2 1.2 16 - 24 Hours/Day 1.0 1.2 1.4 1.4 1.4 1.4 1.4
Conditions Intermittent Load Even Load Stopping or Reversing Heavy Unit Loads No Lubrication Dirty Conditions Moisture
HB-828 - 12/03
Single Strand CDLR
Single Strand CDLR

Units
Intermediate Drive - Model LRSS
HOW TO ORDER Quantity 2 Model No. LRSS W 35 Variable Length 39-10 HP 1/2 Centers 4-1/2 Options ---
Basic Data 1 2 3 4 5 C571 Drive Section, 1.90 x .148 (9 ga.) Rollers C127 End Roller Unit C572 Conveyor Section Motor/Reducer, HP as required, totally enclosed, 50 FPM C1231 Floor Supports with Knee Braces
For Chain Pull and Horsepower Calculations, see the Engineering Data section.
HB-828 - 12/03
Single Strand CDLR - 17
Single Strain CDLR
CONVEYOR WIDTH DRIVE END ROLLER CONVEYOR SECTION
Standard -17, 23, 29, 35 and 41 Between Frames. Effective Conveying width = W - 2. Standard - Intermediate type with direct sprocket connection to single strand driving chain. Standard - 2.56 dia. x .180 (7 ga.) steel roller with grease packed bearings and 11/16 hex axle. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the opposite side. Standard - Welded butt. Standard - 1.90 dia. x .148 (9 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex spring loaded axles on 4-1/2 or 6 centers. One (1) 50A14 rack tooth sprocket welded to each roller. Rollers are mounted 3/8 high on one side. Standard - #50 side bow chain. Standard - Floor type on maximum 10-0 centers for a conveying height of 27 to 333 (1500# capacity). Option - Other floor supports are available (see Supports section). Standard - Right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, for 50 FPM. Option - Intermediate lengths are available in increments of roller centers only (see Components section). Option - Standard angle or channel guards available (see Accessories section). Option - As required (see Controls section).
COUPLINGS CARRYING ROLLERS
CHAIN SUPPORTS
MOTOR / REDUCER LENGTHS SIDE GUARDS ELECTRICAL CONTROLS
HB-828 - 12/03
Single Strand CDLR
End Drive - Model LRSC

HOW TO ORDER Quantity 1 Model No. LRSC W 29 HP 1/2 Options ---
Note: See the C557 Curve topic in this section
Basic Data 1 2 3 4 5 HB-828 - 12/03 C573 Drive Section C127 End Roller C557 - 90 Curve, 2.50 x 1.69 Tapered Rollers Motor/Reducer, HP as required, totally enclosed, 50 FPM C1231 Floor Supports (2) and (1) C1230 Single Leg Support Single Strand CDLR - 19
Single Strain CDLR
CAPACITY CONVEYOR WIDTH DRIVE END ROLLER CURVED CONVEYOR SECTION
Standard - 300 lbs. effective chain pull. Standard - 17, 23, 29, 35 and 41 Between Frames. Effective Conveying width = W - 2. Standard - End type with chain and sprocket connection to 2.56 dia. x .180 (7 ga.) roller. Standard - 2.56 dia. x .180 (7 ga.) steel roller with grease packed bearings and 11/16 hex axle. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the opposite side. Option - Available in 45 and 60 segments. Standard - Welded butt. Standard - 2.50 to 1.69 dia. tapered rollers x .065 (16 ga.) steel with B1020-2 grease packed bearings and 7/16 hex spring loaded axles. One (1) 50A13 rack tooth sprocket welded to small end. Rollers are mounted 3/8 high on one side. Standard - #50 side bow chain. Standard - Floor type for conveying height of 27 to 33 (1500 lbs. capacity). Option - Other supports, hanger or floor type are available (see Supports section). Standard - 1/2 HP right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, for 50 FPM. Option - Standard angle guards available (see Accessories section). Option - As required (see Controls section).
CHAIN SUPPORTS
MOTOR / REDUCER SIDE GUARDS ELECTRICAL CONTROLS
HB-828 - 12/03
Single Strand CDLR
Components
C571 Intermediate Drive
HOW TO ORDER Quantity 2 Code No. C571 W 17 HP 1/2 Speed 70 Voltage 230 Options ---
Standard Available Speeds FPM 25 30 40 50 60 70 85 110 Reducer RPM 43 43 43 86 86 86 86 173 Reducer Sprocket 50B16 50B20 50B26 50B16 50B20 50B23 50B28 50B18 1.90 Roll Sprocket 50A14 50A14 50A14 50A14 50A14 50A14 50A14 50A14
HB-828 - 12/03
Single Strain CDLR
CAPACITY CONVEYOR WIDTH DRIVE FRAME
Standard - 500 lbs. effective chain pull, 1-1/2 HP maximum. Standard - 17, 23, 29, 35 and 41 Between Frames Effective Conveying Width = W - 2. Standard - Drive includes 3-0 of conveyor tread. This drive is reversible. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the opposite side. Standard - Welded butt. Standard - 1.90 dia. x .148 (9 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex spring loaded axles on 4-1/2 centers. One (1) 50A14 sprocket welded to each roller. Standard - #50 side bow chain. Standard - Totally enclose scalloped chain guard.
COUPLINGS ROLLERS
CHAIN CHAIN COVER
HB-828 - 12/03
Single Strand CDLR
C573 End Drive

HOW TO ORDER Quantity 1 Code No. C573 W 29 HP 1/2 Speed 60 Voltage 230 Options ---
Standard Available Speeds Speed FPM 25 30 40 50 60 70 85 110 Reducer RPM 43 43 43 86 86 86 86 173 Reducer Sprocket 50B16 50B20 50B26 50B16 50B20 50B23 50B28 50B18
HB-828 - 12/03
Single Strain CDLR
CAPACITY CONVEYOR WIDTH DRIVE
Standard - 300 lbs. effective chain pull, 1-1/2 HP maximum. Standard - 17, 23, 29, 35 and 41 Between Frames. Effective Conveying Width = W - 2. Standard - This drive should be used for single direction only and would be placed at the discharge end of the conveyor. Drive is furnished as shown for position of shaft, etc. Option - For opposite hand, specify under Options in How To Order. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the opposite side. Standard - Welded butt. Standard - 2.56 dia. x .180 (7 ga.) steel with 11/16 hex stub shaft on one end and 1 dia. stub shaft on the opposite end. Standard - #50 side bow chain. Totally enclosed scalloped chain guard.
FRAME
COUPLINGS ROLLERS CHAIN CHAIN COVER
HB-828 - 12/03
Single Strand CDLR
C559 End Drive

HOW TO ORDER Quantity 1 Code No. C559 W 17 Options ---
CAPACITY CONVEYOR WIDTH DRIVE
Standard - 300 lbs. effective chain pull. Standard - 17, 23, 29, 35 and 41 Between Frames. Effective Conveying width = W - 2 Standard - This drive should be used for single direction only and would be placed at the discharge end of the conveyor. Drive is furnished as shown for position of shaft, etc. Option - For opposite hand, specify under Options in How To Order. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the opposite side. Standard - Welded butt. Standard - 2.56 dia. x .180 (7 ga.) steel with 11/16 hex stub shaft on one end and 1 dia. stub shaft on the opposite end. Standard - Totally enclosed scalloped chain guard.
FRAME
COUPLINGS ROLLERS CHAIN COVER
HB-828 - 12/03
Single Strain CDLR
C127 End Section

CAPACITY CONVEYOR WIDTH END SECTION
Standard - 500 lbs. effective chain pull. Standard - 17, 23, 29, 35 and 41 Between Frames. Effective Conveying Width = W - 2. Standard - This end section is furnished as shown for position of sprocket, etc. Option - For opposite hand, specify under Options in How To Order. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the 9pposite side. Standard - Welded butt. Standard - 2.56 dia. x .180 (7 ga.) steel with 11/16 hex axle.
FRAME COUPLINGS ROLLERS
HB-828 - 12/03
Single Strand CDLR
C572 Intermediate Tread Sections

HOW TO ORDER Quantity 1 Code No. C572 W 29 Length 120 Roller Centers 6
CAPACITY CONVEYOR WIDTH FRAME
Standard - 500 lbs. effective chain pull. Standard - 17, 23, 29, 35 and 41 Between Frames. Effective Conveying Width = W - 2. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the opposite side. Standard - Welded butt. Standard - 1.90 dia. x .148 (9 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex spring loaded axles. One (1) 50A14 rack tooth sprocket welded to each roller. Standard - 4-1/2 or 6. Standard #50 side bow chain. Standard - Totally enclosed scalloped chain guard.
COUPLINGS ROLLERS
ROLLER SPACING CHAIN CHAIN COVER
HB-828 - 12/03
Single Strain CDLR
C557 Curve
HOW TO ORDER Quantity 1 Code No. C557 W 35 Degree 90
Between Frames 17 23 29 35 41
*Inside Radius 2-10-3/8 3-9-7/8 4-9-5/16 5-8-3/4 6-8-1/8
Centerline Radius 3-7-7/8 4-10-3/8 6-13/16 7-3-1/4 8-5-5/8
No. of rollers in 90 18 24 30 36 42
Roller Centers Inside 3.17 3.13 3.10 3.09 3.07 Centerline 3.83 3.82 3.81 3.81 3.80 Outside 4.48 4.50 4.52 4.53 4.54
HB-828 - 12/03
Single Strand CDLR
CAPACITY CONVEYOR WIDTH CURVE FRAME COUPLINGS ROLLERS
Standard - 100 lbs. effective chain pull. Standard - 17, 23, 29, 35 and 41 Between Frames. Effective Conveying Width = W - 2 Standard - 90 Option - 30, 45 or 60 are available. Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the inside rail. 3-1/2 x 1-1/2 x .120 formed steel channel on the outside rail. Standard - Welded butt. Standard - 2.50 to 1.69 tapered roller x .065 (16 ga.) steel with B1020-2 grease packed bearings and 7/16 hex spring loaded axles. One (1) 50A13 rack tooth sprocket welded to each roller. Standard - #50 side bow chain. Standard - Totally enclosed scalloped chain guard.
CHAIN CHAIN COVER
Note: A full width support is required on all curves.
HB-828 - 12/03
Single Strain CDLR

Shown below are Typical arrangement of the C557 Curve when use with other components. The conveyor illustrated consists of one C127 end section, one C557 curved section and one C573 end drive. Straight intermediate section (type C572) can be added between curve and end section or between curve and drive. The straight conveyor at the receive end of the curve should be limited to 100# effective chain pull to minimize resultant pull through curve. The drive should be at the discharge end and the straight discharge conveyor can utilize the full capacity of the chain.
Not Recommended For Reversing Service The conveyor pictured on the following page consists of two C127 end section, one C557 curved section and one C571 drive (includes 3-0 straight section). Straight intermediate sections (type C572) can be added between curve and end section or between curve and drive. The straight conveyor at the receive end of the curve should be limited to 100# effective chain pull to minimize resultant pull through curve. The drive should be near the discharge end and the straight discharge conveyor can utilize the full capacity of the chain.
HB-828 - 12/03
Single Strand CDLR
Full Width Support Required At Center of Curve
HB-828 - 12/03
Single Strain CDLR
C546 - 30 Spur
Between Frames 17 23 29 35 41
A 2-6-1/2 2-11 3-3-1/2 3-8 4-1/2
B 1-5-5/8 1-8-1/4 1-10-13/16 2-1-7/16 2-4
X 2-1-5/8 2-6-3/4 2-11-7/8 3-5-1/8 3-10-3/8
Y 3-8-1/4 4-5-1/4 5-2-1/4 5-11-1/4 6-8-1/4
HB-828 - 12/03
Single Strand CDLR
CAPACITY CONVEYOR WIDTH FRAME
Standard - 300 lbs. effective chain pull. Standard - 17, 23, 29, 35 and 41 Between Frames. Effective Conveying With = W - 2 Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on the chain side. 3-1/2 x 1-1/2 x .120 formed steel channel on the opposite side. Standard - Welded butt. Standard - 1.90 dia. x .148 (9 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex spring loaded axles. Standard - #50 side bow chain. Standard - This spur is furnished as shown for position of sprocket, chain guard, etc. Option - For opposite hand, specify under Options in How To Order. Standard - Totally enclosed scalloped chain guard.
COUPLINGS ROLLERS CHAIN SPUR
CHAIN COVER
HB-828 - 12/03
Single Strain CDLR
C547 - Power Crossover Section

HOW TO ORDER Quantity 1 Code No. C547 Crossover W 19
Standard Widths Crossover W To Match Conveyor W Effective Conveying Width FRAME ROLLERS 19 17 15 25 23 21 31 29 27 37 35 33 43 41 39
Standard - 4-5/8 x 1-1/2 x .120 formed steel channel on both sides. Standard - Two outside rollers are 1.90 dia. x .148 (9 ga.) steel with B1020-2 grease packed bearings and 7/16 hex axles. One (1) 50A14 rack tooth sprocket is welded to one end. One center roller is 2.56 x .180 (7 ga.) steel with B1064-2 grease packed bearings and 11/16 hex axle. One (1) 50A17 sprocket is welded to each end. Standard - Welded butt. Standard - #50 side bow chain. Standard - Totally enclosed scalloped chain guard.
COUPLINGS CHAIN CHAIN COVER
HB-828 - 12/03
Roller To Roller CDLR

Units
Model RRCD190
HOW TO ORDER Quantity 1 Model No. RRCD190 W 27 Variable Length 40-0 HP 1/2 Options 6 centers
HB-828 - 12/03
Roller To Roller CDLR - 35
Basic Data 1 2 3 4 5 C20002 Drive Section, 190 x .109 (12 ga.) Rollers C20000 Intermediate Section Motor/Reducer, HP as required, totally enclosed, 50 FPM C681 Floor Supports - 26 Nominal height C20003 Inverted Drive (Optional)
CONVEYOR WIDTH DRIVE SECTION
Standard - 18 thru 39 Between Frames in 3 increments. Effective width = W - 3-1/4 Standard - Intermediate type with roller to roller chain connection. Motor/Reducer mounted above the conveyor section as standard. Option - Motor/Reducer available in inverted position. Specify with C20003 under options.
CONVEYOR TREAD SECTION Standard - 5 x 2 x .180 (7 ga.) formed steel channel on both sides, rollers low. COUPLINGS CARRYING ROLLERS Standard - Welded butt. Standard - 1.90 dia. x .109 (12 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex spring loaded axles on 4 centers. Two (2) 40A18 sprockets welded to each roller. Rollers are mounted 13/16 low. Option - Rollers are also available on 6 or 8 centers (see Components section). Regreaseable bearings are also available. Option - 5 x 2 x .180 (7 ga.) formed steel channel on the chain side and 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side is available (see Components section). Standard - #40 roller chain. For chain pull calculations, see Engineering Data section, Chain Pull and Horsepower Calculations topic. Standard - floor type on maximum 10-0 center for a conveying height of 30 (3000# capacity). Option - Other floor supports are available (see Supports section). Standard - Right angle reducer, 3 phase, 60 hertz, 230/460 volts, totally enclosed motor, for 50 FPM. Option - Other motors and reducers are available as load and speed change (see Components section). For HP calculations, see Engineering Data section, Chain Pull and Horsepower Calculations topic. Option - Intermediate lengths are available in increments of two times the roller centers only (see Components section). Option - As required (see Controls section).
ROLLERS SHIGH
CHAIN
SUPPORTS
MOTOR/REDUCER
LENGTHS ELECTRICAL CONTROLS
HB-828 - 12/03
Model RRCD250
HOW TO ORDER Quantity 1 Model No. RRCD250 W 30 Variable Length 30-0 HP 1 Options 6 Centers
HB-828 - 12/03
Basic Data 1 2 3 4 5 C20014 Drive Section, 2.50 x .120 (11 ga.) Rollers C20010 Intermediate Section, 6 x 2 x 7 ga. formed channel Motor/Reducer, HP as required, totally enclosed, 50 FPM C699 Floor Supports - 26 Nominal Height C20016 Inverted Drive (Optional)
Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - Intermediate type with roller to roller chain connection. Motor/Reducer mounted above the conveyor section as standard. Option - Motor/Reducer available in inverted position. Specify with C20016 under options.
CONVEYOR TREAD SECTION Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides, rollers low. Option - Also available with structural channel frame (see Components section). COUPLINGS CARRYING ROLLERS Standard - Welded butt. Standard - 2.50 dia. x .120 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles on 4-1/2 centers. Two (2) 60A15 sprockets welded to each roller. Rollers are mounted 1-3/ 4 low. Option - Rollers are also available on 6, 7-1/2 or 9 centers (see Components section). Regreaseable bearings are also available. Option - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side is available (see Components section). Standard - #60 roller chain. For chain pull calculations, see Engineering Data section, Chain Pull and Horsepower Calculations topic. Standard - Floor type on maximum 10-0 centers for a conveying height of 30 (6000# capacity). Option - Other floor supports are available (see Supports section). Standard - Right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, for 50 FPM. Option - Other motors and reducers are available as load and speed change (see Components section). For HP calculations, see Engineering Data section, Chain Pull and Horsepower Calculations topic. Option - Intermediate lengths are available in increments of two times the roller centers only (see Components section). Option - As required (see Controls section).
ROLLERS HIGH
CHAIN
SUPPORTS
MOTOR/REDUCER
HB-828 - 12/03
Model TTRC250 True Tapered Curve

HOW TO ORDER Quantity 1 Model No. TTRC250 W 30 Style 1 HP 1 Options RG
W 24 30 36 42
Dia. Large End 3.910 4.268 4.627 4.985
W 48 54 60
Dia. Large End 4.547 4.799 5.000
HB-828 - 12/03
CONVEYOR WIDTH
Standard - 24 thru 60 Between Frames in 6 increments. For 24 to 42 W, the Inside Radius = 42. For 48 to 60 W, the Inside Radius = 61. Effective Conveying Width = W - 3-3/4. Standard - Intermediate type with roller to roller chain connection. Motor/Reducer mounted above the conveyor section (Style 1) or below the conveyor section (Style 2). 3 HP motors or motors with brakes must be mounted below the conveyor section. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides, rollers low. Standard - Welded butt. Standard - 2.50 dia. x .120 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles on fixed centers. Two (2) 60A15 sprockets welded to each roller. Rollers are mounted 1-3/4 low. Rollers have a welded 11 ga. true tapered shell. Option - Regreaseable bearings are available (add RG under Options in How To Order). Option - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side is available (see Components section). Standard - #60 roller chain. For chain pull calculations, see Engineering Data section, Chain Pull and Horsepower Calculations topic. Standard - Floor type on maximum 10-0 centers for a conveying height of 30 (6000# capacity). Option - Other floor supports are available (see Supports section). Standard - Right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, for 50 FPM. Option - Other motors and reducers are available as load and speed change (see Components section). For HP calculations, see Engineering Data section, Horsepower Calculations topic. Option - As required (see Controls section).
DRIVE SECTION
CURVED CONVEYOR SECTION COUPLINGS CARRYING ROLLERS
ROLLERS HIGH
CHAIN
SUPPORT
MOTOR/REDUCER
ELECTRICAL CONTROLS
HB-828 - 12/03
Model RRCD256
HOW TO ORDER Quantity 1 Model No. RRCD256 W 30 Variable Length 30-0 HP 3/4 Options 6 Centers
HB-828 - 12/03
Basic Data 1 2 3 4 5 C20024 Drive Section, 2.56 x .180 (7 ga.) Rollers C20020 Intermediate Section, 6 x 2 x 7 ga. formed channel Motor/Reducer, HP as required, totally enclosed, 50 FPM C699 Floor Supports - 26 Nominal Height C20026 Inverted Drive (Optional)
Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - Intermediate type with roller to roller chain connection. Motor/Reducer mounted above the conveyor section as standard. Option - Motor/Reducer available in inverted position. Specify with C20026 under options.
CONVEYOR TREAD SECTION Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides, rollers low. Option - Also available with structural channel frame (see Components section). COUPLINGS CARRYING ROLLERS Standard - Welded butt. Standard - 2.56 dia. x .180 (7 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles on 4-1/2 centers. Two (2) 60A15 sprockets welded to each roller. Rollers are mounted 1-3/4 low. Option - Rollers are also available on 6, 7-1/2 or 9 centers (see Components section). Regreaseable bearings are also available. Option - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side is available (see Components section). Standard - #60 roller chain. for chain pull calculations, see Engineering Data section, Chain Pull and Horsepower Calculations topic. Standard - Floor type on maximum 10-0 centers for a conveying height of 30 (6000# capacity). Option - Other floor supports are available (see Supports section). Standard - right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, for 50 FPM. Option - Other motors and reducers are available as load and speed change (see Components section). For HP calculations, see Engineering Data section, Horsepower Calculations topic. Option - Intermediate lengths are available in increments of two times the roller centers only (see Components section). Option - As required (see Controls section).
ROLLERS HIGH
CHAIN
SUPPORTS
MOTOR/REDUCER
HB-828 - 12/03
Model RRCD350
HOW TO ORDER Quantity 1 Model No. RRCD350 W 66 Variable Length 50-0 HP 3 Options 6 Centers
HB-828 - 12/03
Basic Data 1 2 3 4 5 C20036 Drive Section, 3.50 x .300 wall Rollers C20030 Intermediate Section, 7 x 2 x 7 ga. formed channel Motor/Reducer, HP as required, totally enclosed, 50 FPM C1570 Floor Supports C20037 Inverted Drive (Optional)
Standard - 18 thru 72 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - Intermediate type with roller to roller chain connection. Motor/Reducer mounted above the conveyor section as standard. Option - Motor/Reducer available in inverted position. specify with C20037 under options.
CONVEYOR TREAD SECTION Standard - 7 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Also available with structural channel frame (see Components section). COUPLINGS CARRYING ROLLERS Standard - Welded butt. Standard - 3.50 dia. x .300 wall steel rollers with B1084-2 grease packed bearings and 1-1/16 hex axles on 6 centers. Two 92) 60A20 sprockets welded to each roller. Rollers are mounted 1-3/4 low. Option - rollers are also available on 9 or 12 centers (see Components section). Regreaseable bearings are also available. Option - 7 x 2 x .180 (7 ga.) formed steel channel on the chain side and 5 x 2 x 180 (7 ga.) formed steel channel on the opposite side is available (see Components section). Standard - #60 roller chain. For chain pull calculations, see Engineering Data section, Chain Pull and Horsepower Calculations topic. Standard - Floor type on approximate 5-0 centers for a conveying height of 30 (12,000# capacity). Option - Other floor supports are available (see Supports section). Standard - Right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, for 50 FPM. Option - Other motors and reducers are available as load and speed change (see Components section). For HP calculations, see Engineering Data section, Horsepower Calculations topic. Option - Intermediate lengths are available in increments of two times the roller centers only (see Components section). Option - As required (see Controls section).
ROLLERS HIGH
CHAIN
SUPPORTS
MOTOR/REDUCER
HB-828 - 12/03
Components
C20002/C20003 Intermediate Drive Section (1.90 dia. Rollers)
HOW TO ORDER Quantity 1 Code No. C20002 W 21 Length 60 Roller Centers 6 Speed 50 HP 3/4 Voltage 230 Options HH
HB-828 - 12/03
Motor/Reducer Selection Table Nominal Conveyor Speed (FPM) 30 Chain Pull (lbs.) 250 380 545 215 40 320 455 180 50 265 355 580 150 60 230 305 495 HP Required 1/2 3/4 1 1/2 3/4 1 1/2 3/4 1 1-1/2 1/2 3/4 1 1-1/2 115 19 86 21 69 21 69 16 Nominal Reducer Output (RPM) No. of Teeth in Driver Sprocket
CONVEYOR WIDTH FRAME COUPLINGS ROLLER SPACING ROLLERS
Standard - 18 thru 39 Between Frames in 3 increments. Effective Conveying Width = W - 3-1/4 Standard - 5 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - Welded butt. Standard - 4, 6 and 8. Standard - 1.90 dia. x .109 (12 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex spring loaded axles. Two (2) 40A18 sprockets welded to each roller. Rollers are mounted 13/16 low.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH (One Side) Option - 5 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #40 roller chain. Standard - Fully enclosed scalloped chain guard, .120 (11 ga.) Option - Motor/Reducer available in inverted position. Order as C20003. Option - For motors with a brake, specify B under Options on How To Order.
CHAIN CHAIN COVER MOTOR/REDUCER BRAKE
HB-828 - 12/03
C20000 Intermediate Tread Section (1.90 dia. Rollers)

HOW TO ORDER Quantity 1 Code No. C20000 W 27 Length 120 Roller Centers 6 Options HH
CONVEYOR WIDTH FRAME COUPLINGS ROLLER SPACING ROLLERS
Standard - 18 thru 39 Between Frames in 3 increments. Effective Conveying Width = W - 3-1/4. Standard - 5 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - Welded butt. Standard - 4, 6 or 8. Standard - 1.90 dia. x .109 (12 ga.) steel rollers with B100-2 grease packed bearings and 7/16 hex spring loaded axles. Two (2) 40A18 sprockets welded to one end of each roller. rollers are mounted 13/ 16 low.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH (One Side) Option - 5 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #40 roller chain. Standard - Fully enclosed scalloped chain guard, .120 (11 ga.)
CHAIN CHAIN COVER
HB-828 - 12/03

The tables below are based on the frame and roller capacities and deflection of frame, whichever is the lowest. Rollers Low Between Frames Dimensions 18 21 24 27 30 33 36 39 5-0 Support Centers Roller Centers 4 618 618 618 618 614 610 576 542 6 412 412 412 412 409 407 384 361 8 309 309 309 309 307 305 288 271 4 375 373 371 369 368 366 364 363 Total Load Capacity (lbs./ft.) 5 x 2 x .180 (7 ga.) formed steel channel on both sides 10-0 Support Centers Roller Centers 6 379 378 376 375 374 373 371 361 8 309 309 309 309 307 305 288 271
Roller High
Total Load Capacity (lbs./ft.) 5 x 2 x .180 (7 ga.) formed steel channel on the chain side 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side
Between Frames Dimensions 18 21 24 27 30 33 36 39
5-0 Support Centers Roller Centers 4 618 618 618 618 614 610 576 542 6 412 412 412 412 409 407 384 361 8 309 309 309 309 307 305 288 271 4 318 316 314 312 310 308 306 304
10-0 Support Centers Roller Centers 6 323 322 320 319 317 316 315 313 8 309 309 309 309 307 305 288 271
HB-828 - 12/03
C20004 Straight Faced Roller Curve (1.90 dia. Rollers)

Curve available in 90 only. This curve is powered by adjacent straight conveyor. Dimension Table Radii Between Frames 18 21 24 27 30 33 36 39 Inside 47.10 44.10 41.10 38.10 35.10 32.10 29.10 26.10 Effective Conveying Width Centerline 54.48 52.98 51.48 49.98 48.48 46.98 45.48 43.98 Outside 65.10 65.10 65.10 65.10 65.10 65.10 65.10 65.10 Inside Rail 3.70 3.46 3.23 2.99 2.76 2.52 2.29 2.05 Roller Centers at Effective Conveying With Centerline 4.28 4.16 4.04 3.92 3.81 3.69 3.57 3.45 Outside Rail 5.11 5.11 5.11 5.11 5.11 5.11 5.11 5.11
HB-828 - 12/03
CONVEYOR WIDTH FRAME COULINGS ROLLER SPACING ROLLERS
Standard - 18 thru 39 Between Frames in 3 increments. Effective Conveying Width = W - 3-1/4. Standard - 5 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - Welded butt. Standard - Approximate 5-1/8 centers on the outside rail. Standard - Twenty (20) 1.90 dia. x .109 (12 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex spring loaded axles. Two (2) 41A18H sprockets welded to one end of each roller.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH Option - 5 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #40 roller chain. Standard - Fully enclosed scalloped chain guard, .120 (11 ga.).
CHAIN CHAIN COVER
HB-828 - 12/03
C20001 Chain Crossover (1.90 dia. Roller)

HOW TO ORDER Quantity 1 Code No. C20001 W 21 Roller Centers 4 Options ---
Standard Widths (Order By Conveyor W) Note: When ordering this Crossover, use the W dimension of the adjoining conveyor sections. Effective Conveying Width 18 21 24 27 30 33 36 39
14-3/4 17-3/4 20-3/4 23-3/4 26-3/4 29-3/4 32-3/4 35-3/4
FRAME COUPLINGS ROLLER
Standard - 5 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - Welded butt. Standard - 1.90 dia. x .109 (12 ga.) steel rollers with B1020-2 grease packed bearings and 7/16 hex axle. Two (2) 40A18 sprockets welded to each end.
REGREASEABLE BEARINGS Option - Regreaseable bearings are available. Specify RG under Options on How To Order. CHAIN CHAIN COVER Standard - #40 roller chain. One (1) loop included. Standard - Fully enclosed scalloped chain guard, .120 (11 ga.).
HB-828 - 12/03
C20014 Intermediate Drive Section (2.50 dia. Rollers)

HOW TO ORDER Quantity 1 Code No. C20014 W 27 Section Length 60 Roller Centers 6 Speed 30 HP 3/4 Voltage 460 Options HH
CONVEYOR WIDTH FRAME
Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as C20015 or C20017 inverted. Standard - Welded butt. Standard - 4-1/2, 6, 7-1/2 and 9. Standard - 2.50 dia. x .120 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles. Two (2) 60A sprockets welded to each roller. 15 tooth for 4-1/2 centers. 16 tooth for 6, 7-1/2 and 9 centers.
COUPLINGS ROLLER SPACING ROLLERS
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH (One Side) Option - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #60 roller chain. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.) Option - Motor/Reducer available in inverted position. Order as C20016. Option - For motors with a brake, specify B under Options on How To Order. Standard - Punched for C699 or C681 type supports.
CHAIN CHAIN COVER MOTOR/REDUCER BRAKE SUPPORT
HB-828 - 12/03
Motor/Reducer Selection Table Nominal conveyor Speed (FPM) Chain Pull (lbs.) 230 365 30 485 905 1200 185 40 295 390 735 980 175 265 50 380 570 850 1140 150 225 60 320 480 715 965 HP Required 1/2 3/4 1 1-1/2 2 1/2 3/4 1 1-1/2 2 1/2 3/4 1 1-1/2 2 3 1/2 3/4 1 1-1/2 2 3 86 17 69 18 58 17 43 17 Nominal Reducer Output (RPM) No. of Teeth in Driver Sprocket
HB-828 - 12/03

HOW TO ORDER Quantity 2 Code No. C20010 W 27 Length 120 Roller Centers 6 Options ---
HB-828 - 12/03
Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W -3-3/4 Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as C20011. Standard - Welded butt. Standard - 4-1/2, 6, 7-1/2 and 9. Standard - 2.50 dia. x .120 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles. Two (2) 60A sprockets welded to each roller. 15 tooth for 4-1/2 centers. 16 tooth for 6, 7-1/2 and 9 centers.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH (One Side) Option - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #60 roller chain. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.). Standard - Punched for C699 or C681 type supports.
CHAIN CHAIN COVER SUPPORT
The tables on the following page are based on the frame and roller capacities and deflection of frame, whichever is the lowest.
HB-828 - 12/03
Formed Steel Channel Rollers Low

6 x 2 x .180 (7 ga.) formed steel channel on both sides
Total Load Capacity (lbs./ft.) Rollers High

6 x 2 x .180 (7 ga.) formed steel channel on both sides 4 x 2 x .180 (7 ga.) formed steel channel on the opp. side 5-0 Support Centers Roller Centers 9 4-1/2 6 809 809 809 809 809 809 809 809 801 792 791 791 784 777 737 7-1/2 647 647 647 647 647 647 647 647 641 634 633 633 627 622 590 9 540 540 540 540 540 540 540 540 534 528 528 527 523 518 492 490 1079 489 1079 487 1079 486 1079 484 1079 483 1079 481 1079 480 1079 478 1068 476 1056 475 1055 473 1054 472 1045 470 1036 469 983 298 295 292 289 285 282 279 275 272 269 265 262 259 256 252 10-0 Support Centers Roller Centers 4-1/2 6 307 304 302 299 297 294 291 289 286 284 281 279 276 273 271 7-1/2 312 310 308 305 303 301 299 297 295 293 291 288 286 284 282 9 315 313 311 310 308 306 304 302 301 299 297 295 293 291 290
5-0 Support Centers W Dim. 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 Roller Centers 4-1/2 6 7-1/2 647 647 647 647 647 647 647 647 641 634 633 633 627 622 590 9 540 540 540 540 540 540 540 540 534 528 528 527 523 518 492 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1068 801 1056 792 1055 791 1054 791 1045 784 1036 777 983 737
10-0 Support Centers Roller Centers 4-1/2 476 473 471 468 465 462 460 457 454 451 448 446 443 440 437 6 483 481 479 477 475 472 470 468 466 464 462 460 457 455 453 7-1/2 487 486 484 482 480 479 477 475 473 471 470 468 466 464 462
Structural Steel Channel Rollers Low

6 @ 8.2 structural steel channel on both sides 5-0 Support Centers W Dim. 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 Roller Centers 4-1/2 6 7-1/2 647 647 647 647 647 647 647 647 641 634 633 633 627 622 590 9 540 540 540 540 540 540 540 540 534 528 528 527 523 518 492 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1068 801 1056 792 1055 791 1054 791 1045 784 1036 777 983 737 933 930 927 924 922 919 916 913 910 908 905 902 899 896 894 10-0 Support Centers Roller Centers 4-1/2 6 809 809 809 809 809 809 809 809 801 792 791 791 784 777 737 7-1/2 647 647 647 647 647 647 647 647 641 634 633 633 627 622 590 9 540 1079 540 1079 540 1079 540 1079 540 1079 540 1079 540 1079 540 1079 534 1068 528 1056 528 1055 527 1054 523 1045 518 1036 492 983

6 @ 8.2 structural steel channel on chain side 5 @ 5.4 structural steel channel on the opp. side 4-0 Support Centers Roller Centers 4-1/2 6 809 809 809 809 809 809 809 809 801 792 791 791 784 777 737 7-1/2 647 647 647 647 647 647 647 647 641 634 633 633 627 622 590 9 540 540 540 540 540 540 540 540 534 528 528 527 523 518 492 454 451 447 444 441 437 434 431 427 424 421 418 414 411 408 10-0 Support Centers Roller Centers 4-1/2 6 462 460 457 454 452 449 447 444 442 439 437 434 431 429 426 7-1/2 467 465 463 461 459 457 454 452 450 448 446 444 442 440 437 9 470 469 467 465 463 461 459 458 456 454 452 450 449 447 445
HB-828 - 12/03

Curve available in 90 only. This curve is powered by an adjacent straight conveyor.
HB-828 - 12/03
Dimension Table Radii Between Frames 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 Inside 79.24 76.24 73.24 70.24 67.24 64.24 61.24 58.24 55.24 52.24 49.24 46.24 43.24 40.24 37.24 Effective Conveying Width Centerline 86.37 84.87 83.37 81.87 80.37 78.87 77.37 75.87 74.37 72.87 71.37 69.87 68.37 66.87 65.37 Outside 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 Roller Centers at Effective Inside Rail Conveying Width Centerline 6.22 5.99 5.75 5.51 5.28 5.05 4.81 4.57 4.34 4.10 3.87 3.63 3.40 3.16 2.93 6.78 6.67 6.55 6.43 6.31 6.19 6.07 5.96 5.84 5.72 5.60 5.48 5.37 5.25 5.13 Outside Rail 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64
HB-828 - 12/03
Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as C20019. Standard - Welded butt. Standard - Twenty (20) 2.50 dia. x .120 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles. Two (2) 60A sprockets welded to each roller. Standard - Approximately 7-5/8 centers on the outside rail.
COUPLINGS ROLLERS
ROLLER SPACING
CHAIN CHAIN COVER
HB-828 - 12/03

Standard Widths (Order By Conveyor W)

Note: When ordering this Crossover, use the W dimension of the adjoining conveyor sections.
18 21 24 27 30 33 36 39 42 45 48 51 54 57 60
14-1/4 17-1/4 20-1/4 23-1/4 26-1/4 29-1/4 32-1/4 35-1/4 38-1/4 41-1/4 44-1/4 47-1/4 50-1/4 53-1/4 56-1/4 Effective Conveying Width
Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as 20012. Standard - Welded butt. Standard - 2.50 dia. x .120 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axle. Two (2) 60A sprockets welded to each end.
HB-828 - 12/03

HOW TO ORDER Quantity 1 Code No. C20024 W 27 Section Length 60 Roller Centers 6 Speed 50 HP 3/4 Voltage 460 Options HH
Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as C20015 or C20027 inverted. Standard - Welded butt. Standard - 4-1/2, 6, 7-1/2 and 9. Standard - 2.56 dia. x .180 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles. Two (2) 60A sprockets welded to each roller. 15 tooth for 4-1/2 centers. 16 tooth for 6, 7-1/2 and 9 centers.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH (One Side) Option - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #60 roller chain. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.). Option - Motor/Reducer available in inverted position. Order as C20026 Option - For motors with a brake, specify B under Options on How To Order. Standard - Punched for C699 or C681 type supports.
HB-828 - 12/03
Motor/Reducer Selection Table Nominal conveyor Speed (FPM) Chain Pull (lbs.) 230 365 30 485 905 1200 185 40 295 390 735 980 175 265 50 380 570 850 1140 150 225 60 320 480 715 965 Roller To Roller CDLR - 62 HP Required 1/2 3/4 1 1-1/2 2 1/2 3/4 1 1-1/2 2 1/2 3/4 1 1-1/2 2 3 1/2 3/4 1 1-1/2 2 3 HB-828 - 12/03 86 16 69 17 58 16 43 16 Nominal Reducer Output (RPM) No. of Teeth in Driver Sprocket

Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W -3-3/4 Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as C20021. Standard - Welded butt. Standard - 4-1/2, 6, 7-1/2 and 9. Standard - 2.56 dia. x .180 (11 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles. Two (2) 60A sprockets welded to one end of each roller. 15 tooth for 4-1/2 centers. 16 tooth for 6, 7-1/2 and 9 centers.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH (One Side) Option - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #60 roller chain. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.) Standard - Punched for C699 or C681 type supports.
The tables on the following page are based on the frame and roller capacities and deflection of frame, whichever is the lowest. HB-828 - 12/03 Roller To Roller CDLR - 63


6 x 2 x .180 (7 ga.) formed steel channel on both sides 4 x 2 x .180 (7 ga.) formed steel channel on the opp. side 5-0 Support Centers Roller Centers 9 4-1/2 6 809 809 809 809 809 809 809 809 797 785 784 783 775 768 727 7-1/2 647 647 647 647 647 647 647 647 638 628 627 626 620 614 582 9 540 540 540 540 540 540 540 540 532 524 523 522 517 512 485 488 1079 486 1079 484 1079 481 1079 479 1079 477 1079 475 1079 473 1079 471 1063 469 1047 467 1045 465 1044 463 1034 461 1024 459 970 292 288 283 279 274 270 265 261 256 252 248 243 239 234 230 10-0 Support Centers Roller Centers 4-1/2 6 302 298 295 292 288 285 281 278 275 271 268 264 261 257 254 7-1/2 308 305 302 299 297 294 291 288 285 283 280 277 274 271 269 9 312 309 307 305 302 300 297 295 293 290 288 286 283 281 278
5-0 Support Centers W Dim. 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 Roller Centers 4-1/2 6 7-1/2 647 647 647 647 647 647 647 647 638 628 627 626 620 614 582 9 540 540 540 540 540 540 540 540 532 524 523 522 517 512 485 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1063 797 1047 785 1045 784 1044 783 1034 775 1024 768 970 727
10-0 Support Centers Roller Centers 4-1/2 471 467 463 460 456 452 448 445 441 437 433 430 426 422 418 6 479 476 473 471 468 465 462 459 456 453 450 447 445 442 439 7-1/2 484 482 479 477 475 472 470 468 465 463 461 458 456 453 451

6 @ 8.2 structural steel channel on both sides 5-0 Support Centers W Dim. 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 Roller Centers 4-1/2 6 7-1/2 647 647 647 647 647 647 647 647 638 628 627 626 620 614 582 9 540 540 540 540 540 540 540 540 532 524 523 522 517 512 485 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1079 809 1063 797 1047 785 1045 784 1044 783 1034 775 1024 768 970 727 927 923 920 916 912 908 905 901 897 893 890 886 882 878 875 10-0 Support Centers Roller Centers 4-1/2 6 809 809 809 809 809 809 809 809 797 785 784 783 775 768 727 7-1/2 647 647 647 647 647 647 647 647 638 628 627 626 620 614 582 9 540 1079 540 1079 540 1079 540 1079 540 1079 540 1079 540 1079 540 1079 532 1063 524 1047 523 1045 522 1044 517 1034 512 1024 485 970

6 @ 8.2 structural steel channel on chain side 4 @ 5.4 structural steel channel on the opp. side 5-0 Support Centers Roller Centers 4-1/2 6 809 809 809 809 809 809 809 809 797 785 784 783 626 768 727 7-1/2 647 647 647 647 647 647 647 647 638 628 627 628 620 614 582 9 540 540 540 540 540 540 540 540 532 524 523 522 517 512 485 447 443 438 434 430 425 421 416 412 407 403 398 394 390 385 10-0 Support Centers Roller Centers 4-1/2 6 457 454 450 447 444 440 437 433 430 426 423 420 416 413 409 7-1/2 463 460 458 455 452 449 446 444 441 438 435 432 430 427 424 9 467 465 462 460 458 455 453 450 448 446 443 441 438 436 434
HB-828 - 12/03

HB-828 - 12/03
Dimension Table Radii Between Frames 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 Inside 79.24 76.24 73.24 70.24 67.24 64.24 61.24 58.24 55.24 52.24 49.24 46.24 43.24 40.24 37.24 Effective Conveying Width Centerline 86.37 84.87 83.37 81.87 80.37 78.87 77.37 75.87 74.37 72.87 71.37 69.87 68.37 66.87 65.37 Outside 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 97.24 Roller Centers at Effective Inside Rail Conveying Width Centerline 6.22 5.99 5.75 5.51 5.28 5.05 4.81 4.57 4.34 4.10 3.87 3.63 3.40 3.16 2.93 6.78 6.67 6.55 6.43 6.31 6.19 6.07 5.96 5.84 5.72 5.60 5.48 5.37 5.25 5.13 Outside Rail 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64 7.64
Standard - 18 thru 60 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as C20029. Standard - Welded butt. Standard - Twenty (20) 2.56 dia. x .180 (7 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axles. Two (2) 60A sprockets welded to one end of each roller. Standard - Approximately 7-5/8 centers on the outside rail.
COUPLINGS ROLLERS
ROLLER SPACING
CHAIN CHAIN COVER
HB-828 - 12/03


18 21 24 27 30 33 36 39 42 45 48 51 54 57 60
14-1/4 17-1/4 20-1/4 23-1/4 26-1/4 29-1/4 32-1/4 35-1/4 38-1/4 41-1/4 44-1/4 47-1/4 50-1/4 53-1/4 56-1/4 Effective Conveying Width
Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 6 @ 8.2# structural channel. Order as 20022. Standard - Welded butt. Standard - 2.56 dia. x .180 (7 ga.) steel rollers with B1064-2 grease packed bearings and 11/16 hex axle. Two (2) 60A sprockets welded to each end.
HB-828 - 12/03

HOW TO ORDER Quantity 1 Code No. C20036 W 36 Section Length 72 Roller Centers 12 Speed 50 HP 2 Voltage 230 Options B
18 thru 72 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - 7 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 7 @ 9.8# structural channel. Order as C20038 or C20039 inverted. Standard - Welded butt. Standard - 6, 9 and 12. Standard - 3.50 dia. x .300 wall steel with B1084-2 grease packed bearings and 1-1/16 hex axle. Two 92) 60A20 sprockets welded to each roller.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How to Order ROLLERS HIGH (One Side) Option - 7 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 5 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #60 roller chain. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.) Option - Motor/Reducer available in inverted position. Order as C20037 (formed) or C20039 (structural). Option - For motors with a brake, specify B under Options on How To Order. Standard - Punched for C1570, C699 or C681 type supports.
HB-828 - 12/03
Motor/Reducer Selection Table Nominal Conveyor Speed (FPM) Chain Pull (lbs.) 230 30 365 485 905 185 40 295 390 735 980 175 50 265 380 570 850 150 60 225 320 480 715 HP Required 1/2 3/4 1 1-1/2 1/2 3/4 1 1-1/2 2 1/2 3/4 1 1-1/2 2 1/2 3/4 1 1-1/2 2 69 19 58 19 43 20 43 15 Nominal Reducer Output (RPM) No. of Teeth in Driver Sprocket
HB-828 - 12/03

Standard - 18 thru 72 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - 7 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 7 @ 9.8# structural channel. Order as C2031. Standard - Welded butt. Standard - 6, 9 and 12. Standard - 3.50 dia. x .300 wall steel with B1084-2 grease packed bearings and 1-1/16 hex axle. Two (2) 60A20 sprockets welded to one end of each roller.
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH (One Side) Option - 7 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 5 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Specify HH under Options on How To Order. Standard - #60 roller chain. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.) Standard - Punched for C1570, C699 or C681 type supports.
The tables on the following page are based on the frame and roller capacities and deflection of frame, whichever is the lowest.
HB-828 - 12/03


7 x 2 x .180 (7 ga.) formed steel channel on both sides 5 x 2 x .180 (7 ga.) formed steel channel on the opp. side 5-0 Support Centers Roller Centers 6 1559 1553 1547 1541 1535 1529 1522 1516 1510 1504 1498 1492 1485 1479 1473 1467 1461 1461 1455 9 1575 1571 1566 1562 1558 1554 1549 1545 1541 1537 1532 1528 1524 1520 1515 1511 1507 1507 1503 12 1583 1579 1576 1573 1569 1566 1563 1560 1556 1553 1550 1546 1543 1540 1536 1533 1530 1530 1461 6 400 393 385 378 371 363 356 349 341 334 327 320 312 305 298 290 283 283 276 10-0 Support Centers Roller Centers 9 418 413 408 403 398 393 388 383 378 373 368 363 358 353 348 343 338 338 333 12 427 424 420 416 412 408 404 400 396 392 388 384 381 377 373 369 365 365 361
5-0 Support Centers W Dim. 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 63 66 69 72 Roller Centers 6 2546 2540 2533 2527 2521 2515 2509 2503 2496 2490 2484 2478 2472 2466 2459 2453 2447 2441 2435 9 2218 2218 2218 2218 2218 2218 2218 2218 2218 2218 2194 2170 2167 2166 2158 2150 2049 1948 1863 12 1663 1663 1663 1663 1663 1663 1663 1663 1663 1663 1645 1627 1625 1624 1618 1612 1536 1461 1397
10-0 Support Centers Roller Centers 6 548 577 571 565 559 553 547 540 534 528 522 516 510 503 497 491 485 479 473 9 599 595 591 586 582 578 574 569 565 561 557 552 548 544 540 535 531 527 523 12 607 604 600 597 594 590 587 584 580 577 574 571 567 564 561 557 554 551 547
HB-828 - 12/03

7 @ 9.8 structural steel channel on both sides 5-0 Support Centers W Dim. 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 63 66 69 72 Roller Centers 6 3327 3327 3327 3327 3327 3327 3327 3327 3327 3327 3291 3255 3251 3248 3236 3224 3073 2922 2794 9 2218 2218 2218 2218 2218 2218 2218 2218 2218 2218 2194 2170 2167 2166 2158 2150 2049 1948 1863 12 1663 1663 1663 1663 1663 1663 1663 1663 1663 1663 1645 1627 1625 1624 1618 1612 1536 1461 1397 6 1275 1269 1263 1257 1251 1244 1238 1232 1226 1220 1214 1207 1201 1195 1189 1183 1177 1170 1164 10-0 Support Centers Roller Centers 9 1291 1287 1282 1278 1274 1270 1265 1261 1257 1253 1248 1244 1240 1236 1231 1227 1223 1218 1214 12 1299 1295 1292 1289 1285 1282 1279 1275 1272 1269 1266 1262 1259 1256 1252 1249 1246 1243 1239 6 2629 2623 2617 2611 2605 2598 2592 2586 2580 2574 2568 2561 2555 2549 2543 2537 2531 2531 2524

7 @ 9.8 structural steel channel on chain side 5 @ 6.7 structural steel channel on opposite side 5-0 Support Centers Roller Centers 9 2218 2218 2218 2218 2218 2218 2218 2218 2218 2218 2194 2170 2167 2166 2158 2150 2049 2049 1948 12 1663 1663 1663 1663 1663 1663 1663 1663 1663 1663 1645 1627 1625 1624 1618 1612 1536 1536 1461 6 713 706 698 691 684 676 669 662 655 647 640 633 625 618 611 604 596 596 589 10-0 Support Centers Roller Centers 9 731 726 721 716 711 706 701 696 691 686 681 676 671 666 661 656 651 651 646 12 741 737 733 729 725 721 717 713 709 705 702 698 694 690 686 682 678 678 674
HB-828 - 12/03

HB-828 - 12/03
Dimension Table Radii Between Frames 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 63 66 69 72 Inside 102.88 99.88 96.88 93.88 90.88 87.88 84.88 81.88 78.88 75.88 72.88 69.88 66.88 63.88 60.88 57.88 54.88 51.88 48.88 Effective Conveying Width Centerline 110.01 108.51 107.01 105.51 104.01 102.51 101.01 99.51 98.01 96.51 95.01 93.51 92.01 90.51 89.01 87.51 86.01 84.51 83.01 Outside 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 120.88 Roller Centers at Effective Inside Rail Conveying Width Centerline 8.08 7.84 7.61 7.37 7.14 6.92 6.68 6.44 6.21 5.97 5.74 5.50 5.26 5.03 4.79 4.56 4.32 4.08 3.85 8.65 8.53 8.41 8.29 8.17 8.05 7.93 7.81 7.69 7.58 7.46 7.34 7.22 7.11 6.99 6.87 6.75 6.63 6.52 Outside Rail 9.51 9.51 9.51 9.51 9.51 9.51 9.51 9.51 9.51 9.51 9.51: 9.51 9.51 9.51 9.51 9.51 9.51 9.51 9.51
Standard - 18 thru 72 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Standard - 7 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 7 @ 9.8# structural channel. Order as C20053. Standard - Welded butt. Standard - Twenty (20) 3.50 dia. x .300 wall steel with B1084-2 grease packed bearings and 1-1/16 hex axle. Two (2) 60A20 sprockets welded to one end of each roller. Standard - Approximately 9-1/2 centers on the outside rail.
COUPLINGS ROLLERS
ROLLER SPACING
REGREASEABLE BEARINGS Option - Regreaseable bearings in the conveyor rollers are available. Specify RG under Options on How To Order. ROLLERS HIGH Option - 7 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 5 x 2 x .180 (7 ga.) formed steel channel on opposite side. Specify HH under Options on How To Order. Standard - #60 roller chain. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.).
CHAIN CHAIN COVER
HB-828 - 12/03


18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 63 66 69 72 Effective 14-1/417-1/420-1/423-1/426-1/429-1/432-1/435-1/438-1/441-1/444-1/447-1/450-1/453-1/456-1/459-1/462-1/465-1/468-1/4 Conveying Width
FRAME
Standard - 7 x 2 x .180 (7 ga.) formed steel channel on both sides. Option - Available with 7 @ 9.8# structural channel. Order as 20034W-Length. Standard - Welded butt. Standard - 3.50 dia. x .300 wall steel with B1084-2 grease packed bearings and 1-1/16 hex axle. Two (2) 60A20T sprockets welded to each end.
COUPLINGS ROLLER
REGREASEABLE BEARINGS Option - Regreaseable bearings are available. Specify RG under Option on How To Order CHAIN CHAIN COVER Standard - 3#0 roller chain. One (1) loop included. Standard - Fully enclosed scalloped chain guard, .180 (7 ga.).
HB-828 - 12/03
HB-828 - 12/03
General Specifications
Roller to Roller Chain Driven Live Roller Conveyor - Available as a Standard Product
Roller Assembly Tube Size Bearing Sprocket Axle 7/16 Hex Chain Side 5 x 2 x .180 (7 ga.) Formed Channel Frame Opposite Side 5 x 2 x .180 (7 ga.) Formed Channel 4 x 2 x .180 (7 ga.) Formed Channel 6 x 2 x .180 (7 ga.) Formed Channel 4 x 2 x .180 (7 ga.) Formed Channel 7 x 2 x .180 (7 ga.) Formed Channel 5 x 2 x .180 (7 ga.) Formed Channel
1.90 dia. x .109 wall B1020-2 #40A18
2.50 dia. x .120 wall B1064-2 #60A15 and or 2.56 dia. x .180 wall #60A16 3.50 dia. x .300 wall B1084-2 #60A20
11/16 Hex
6 x 2 x .180 (7 ga.) Formed Channel
1-1/16 Hex
7 x 2 x .180 (7 ga.) Formed Channel
Tube Size 1.90 dia. x .109 wall
Roller Centers 4 6 8 4-1/2 6 7-1/2 9 6 9 12
Cross Brace 2 x 2 x 1/4 Structural Angle 2 x 2 x 1/4 Structural Angle 3 x 3 x 1/4 Structural Angle
Chain W Chain Box Effective Roller Max. Gauge Minimum Maximum Conveying Drive Wicth Chain Size Chain Pull 18 .120 (11 ga.) 39 W - 3-1/4 in 3 incrementsi #40 520#
2.50 dia. x .120 wall and 2.56 dia. x .180 wall 3.50 dia. x .300 wall
.180 (7 ga.)
18
60
W-3-3/4
#60
1200#
in 3 incrementx .180 (7 ga.) 18 72 W-3-3/4 #60 1200#
in 3 increments
Note: To order, see Component or Unit sections.
HB-828 - 12/03
General Specifications - 77
Roller to Roller Chain Driven Live Roller Conveyor - Available as an Engineered Product
(Preferred Construction For Engineered Standards Using Structural Frame Rails) Typical Semi-Standard Construction Roller Dia. 1.90 1.90 1.90 2.50 2.50 2.50 2.56 2.56 2.56 2.56 2.75 2.75 3.50 3.50 3.50 4.0 4.0 4.0 4.25 4.25 4.25 5.0 5.0 6.50 Chain 40 50 60 40 50 60 40 50 60 80 60 80 60 80 100 60 80 100 60 80 100 80 100 100 Minimum Roller Centers 3-1/2 4-1/16 4-1/8 4-1/4 4-11/16 4-7/8 4-1/4 4-11/16 4-7/8 5-1/2 5-1/4 5-1/2 6 6-1/2 6-7/8 6-3/8 7 7-1/2 6-3/8: 7 7-1/2 8 8-3/4 10 A Channel 5 at 7.7# 5 at 6.7# 6 at 8.2# 5 at 6.7# 5 at 6.7# 6 at 8.2# 5 at 6.7# 5 at 6.7# 6 at 8.2# 6 at 8.2# 6 at 8.2# 6 at 8.2# 7 at 9.8# 8 at 11.5# 8 at 11.5# 7 at 9.8# 8 at 11.5# 8 at 11.5# 7 at 9.8# 8 at 11.5# 9 at 13.4# 9 at 13.4# 10 at 15.3# 10 at 15.3# B angle 3-1/2 x 2-1/2 x 5/16 3-1/2 x 2-1/2 x 5/16 4 x 3 x 5/16 3-1/2 x 2-1/2 x 5/16 3-1/2 x 2-1/2 x 5/16 4 x 3 x 5/16 3-1/2 x 2-1/2 x 5/16 3-1/2 x 2-1/2 x 5/16 4 x 3 x 5/16 4 x 3 x 5/16 4 x 3 x 5/16 4 x 3 x 5/16 4 x 3 x 5/16 5 x 3-1/2 5/16 5 x 3-1/2 x 5/16 5 x 3-1/2 x 5/16 6 x 4 x 1/2 6 x 4 x 1/2 5 x 3-1/2 x 5/16 6 x 4 x 1/2 6 x 4 x 1/2 6 x 4 x 1/2 7 x 4 x 1/2 7 x 4 x 1/2
For additional information, please contact your local Field Sales Office.
HB-828 - 12/03
Chain Driven Live Roller Conveyor Units - Approximate Weight Per Foot
Note: Weights are based on formed channel frame. SS CDLR Roller Centers 4-1/2 6 90 Curve 17 W lbs./ft. 32 29 106 23 W lbs./ft. 36 31 182 29 W lbs./ft. 41 35 258 35 W lbs./ft. 43 37 358 41 W lbs./ft 47 40 430
RRCD190 - Intermediate Section Roller Centers 4 6 8 90 Curve 18 W lbs./ft. 40 34 33 240 21 W lbs./ft. 42 36 35 270 24 W lbs./ft. 45 39 36 300 27 W lbs/ft. 48 41 37 300 30 W lbs./ft. 51 43 38 317 33 W lbs./ft. 53 44 39 330 36 W lbs./ft. 56 46 41 345 39 W lbs./ft 58 48 42 360
For CFC Series II, add 10 lbs./ft. to the above weights. RRCD250 - Intermediate Section Roller Centers 4-1/2 6 9 90 Curve 18 W lbs./ft. 64 57 50 590 24 W lbs./ft. 71 64 56 600 30 W lbs./ft. 80 70 61 610 36 W lbs./ft. 88 76 66 655 42 W lbs/ft. 96 82 71 700 48 W lbs./ft. 104 88 76 745 54 W lbs./ft. 110 94 81 790 60 W lbs./ft. 117 100 86 845
For 6 @ 8.2# structural channel frame, add 3.5 lbs./ft. For CFC Series III, add 10 lbs./ft. to the above weights. RRCD350 - Intermediate Section Roller Centers 6 9 12 90 Curve 18 W lbs./ft. 105 89 74 1150 24 W lbs./ft. 122 101 83 1300 30 W lbs./ft. 138 112 92 1450 36 W lbs./ft. 155 125 102 1630 42 W lbs/ft. 171 137 112 1810 48 W lbs./ft. 188 149 121 2000 54 W lbs./ft. 203 160 129 2170 60 W lbs./ft. 220 172 138 2350 66 W lbs./ft. 235 183 147 2530 72 W lbs./ft. 254 195 156 2800
For 7 @ 9.8# structural channel frame, add 8 lbs./ft. For CFC Series IV, add 10 lbs./ft. to the above weights.
HB-828 - 12/03
HB-828 - 12/03
Controlled Flow Conveyor

Application Data - CFC Series II, III and IV - Available as an Engineered Product
Mathews Control Flow Conveyor Series II, III and IV are heavy duty live roller conveyors which permit accumulation of conveyed loads without build up of line pressure. Each consist of a series of interconnected conveying zones which are individually powered by the engagement of a pneumatically controlled low pressure air clutch. The rollers in each zone are connected roller to roller by sprockets and chains. An air clutch is attached to one roller in each zone. Each zone is connected clutch to clutch by sprockets ad chains. CFC Series II, III and IV are gearmotor driven. Standard features are accumulation in one direction, single load release (singulation), and multiple load release (sequential). CFC Series II, III and IV may be reversed and used as transport conveyors for empty pallets.
How CFC Series II, III and IV Accumulation Operates

As products move onto Mathews CFC conveyors, and accumulation is to begin, a load entering the conveyor will be transported through the preceding zone and onto zone 1 at the discharge end of the conveyor, where it will depress a sensing roller. When this sensing device is depressed, the air pressure to the clutch is removed, thus removing driving power from zone 1. A signal is sent to zone 2 so that when its sensing device is depressed its clutch is likewise disengaged. This sequence is represented for accumulation in the remaining zones. The release control at the exit end of the conveyor is a solenoid operated control valve. When an external electrical signal is received, it will release loads singularly or sequentially. Release of a load from zone 1 or removal of a load from any intermediate zone will restart the adjacent upstream zone to fill that empty zone.
Release Modes Singulation

This type of release allows the exit of one product at a time with the issuance of an electrical remote signal. As the article leaves zone 1 sensing device, the signal is terminated, and the following products advance in a sequential fashion.
Sequential
This type of release allows the exit of product in a progressive fashion with the issuance of a maintained electrical signal. A gap (approximately equal to the zone length) is generated between articles.
HB-828 - 12/03
Controlled Flow Conveyor - 81
Application Information
In order to ensure actuation of the sensing rollers, the product to be conveyed must present a firm flat bottom surface to the conveyor rollers. In the case of pallets, at least one continuous bottom member must run the entire length of the pallet. The standard zone lengths are 5-0 and the maximum length for conveyed product should be 12 less than the zone length (6 less for CFC II only). The minimum length of a product to be conveyed is dependent upon the roller centers. For proper conveying at least three rollers should be under the article at all times. In the case of totes with sloped ends, the top and bottom dimension should both be taken into consideration. The minimum article weight is limited by the4 sensitivity of the sensing device. For CFC Series II, 15 lbs. minimum; CFC Series III, 30 lbs. minimum and CFC Series IV, 50lbs. minimum is required to actuate the zone sensing device. Mathews CFC Series II, III and IV use low pressure, non-lubricated dry air from 15 to 30 p.s.i. for its air logic control and actuation of the low pressure air clutches.
HB-828 - 12/03
Units
CFC Series II - (1.90 dia. Rollers)
Basic Data 1 2 3 4 Intermediate Drive Section Conveyor Section Motor/Reducer, HP as required at 58 RPM 3000# capacity Floor Supports
HB-828 - 12/03
CAPACITY CONVEYOR WIDTH
Standard - 1500 lbs. maximum, 15 lbs. minimum per zone. Standard - 12 thru 63 Between Frames in 3 increments. Effective conveying width = W - 3-1/4. Recommended Effective Width should be Product Width + 3. Overall Width = W + 9-1/2. Option - Other widths are available (consult factory). Standard - Each zone is powered through a low pressure disc type air clutch, driven by clutch to clutch #40 roller chain loops from a right angle reducer located near the center of the conveyor. All drive components are enclosed for safety and dirt shielding. Standard - 6 x 2 x .180 (7 ga.) roll formed rail on chain box side. 5 x 2 x .180 (7 ga.) roll formed rail on opposite chain box. Structural angle cross bracing. All welded construction. Standard - Welded butt on both sides. Standard - 1.90 dia. x .109 (12 ga.) steel with grease packed, sealed for life bearings and 7/16 hex axles on 4, 6 or 8 centers. Each roller fitted with 17 tooth #40 roller chain sprockets for roll to roll drive within zones. Rollers are mounted 13/16 low on side opposite chain box. Option - Regreaseable bearings are available. Option - A frame with a 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side for a roller 3/16 high is available. Standard - To control product drift, brakes are included. Standard - #40 roller chain for rollers #40 roller chain for clutches. Standard - Floor type on maximum 10-0 centers for a conveying height of 7-1/2 thru 48 (3000# capacity). Standard - 58 RPM right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, fan cooled, 30 FPM, 1-1/2 HP. Option - Maximum 2 HP. Standard - 10-0 for 4 and 6 roller centers. 9-4 for 8 roller centers. Option - Intermediate lengths are available. Standard - 5-0 for maximum product length of 54 (4 and 6 roller centers). 4-8 for maximum product length of 50 (8 roller centers). Option - Variable in increments of roller centers. Minimum 24, maximum 120 (minimum of three rollers under article). Standard - air logic. Option 7-1/4 minimum, 48 maximum. Option - speeds 30 to 60 FPM. Option - Drive may be located at any zone location in length of conveyor within limitations of capacity calculations. Option - Conveyor may be used for empty pallet transport in the reverse mode with addit9ional controls. Option - As required (see Controls section).
DRIVE
CONVEYOR SECTION
ROLLERS HIGH
BRAKES CHAIN SUPPORTS MOTOR/REDUCER
LENGTHS
ZONE LENGTHS
CONTROL ELEVATION SPEED CHANGES DRIVE LOCATION REVERSING ELECTRICAL CONTROLS
HB-828 - 12/03
Conveyor Capacity Calculations (CFC II)

(A) For conveyors with the drive at or near the center of the conveyor, limit the maximum number of zones per conveyor to the lesser of: 33, 000 x HP x ( Z one Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------------------------------- 0. 0625 x Speed x Zone Length xM aximumLoa d Zone 1120 x ( Zone Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------0.037 xZone Length x M aximum Load Zone (31 Zones Maximum Recommended) (B) For conveyors with the drive at either end of the conveyor, limit the maximum number of zones per conveyor to the lesser of: 33, 000 x HP x ( Z one Length + Pallet Length ) Zones Conveyor = --------------------------------------------------------------------------------------------------------------------------------------------------- 0.0625 x Speed x Zone Length xM aximumLoa d Zone 560 x ( Zone Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------0.037 xZone Length x M aximum Load Zone (15 Zones Maximum Recommended) Note: For Maximum Load/Zone, add 9 lbs. for each roller in the zone, less 1/2 lb. for each 3 that the W is less than 39 HP = Output Horsepower, see table in the Engineering Data section, Dead Loads topic. Speed = Conveyor Speed in FPM Length = Length in feet (C) Zone Loading Maximum Allowable Load (lbs.) per Zone per Given Pallet Length. Based on Roller Capacities 18 Pallet Length 710 630 550 570 500 440 DO NOT USE 24 Pallet Length 1000 880 780 710 630 550 570 500 440 30 Pallet Length 1150 1000 890 860 750 670 570 500 440 36 Pallet Length 1430 1260 1110 1000 880 780 710 630 550 42 Pallet Length 1500 1380 1220 1150 1000 890 860 750 670 48 Pallet Length 1500 1500 1450 1290 1130 1000 1000 880 780
Roller Centers
Between Frames 18
27 39 18
27 39 18
27 39
For additional data or for placing an order, please contact your local Field Sales Office.
HB-828 - 12/03
Heavy Duty CFC Series III - (2.50 dia. Rollers)
Basic Data 1 2 3 4 Intermediate Drive Section Conveyor Section Motor/Reducer, HP as required at 58 RPM 6000# capacity Floor Supports
HB-828 - 12/03
Standard - 3000 lbs. maximum, 30 lbs. minimum per zone. Standard - 18 thru 72 Between Frames in 3 increments. Effective Conveying Width = W - 3-3/4. Recommended Effective Width should be Product Width + 3. Overall Width = W + 9-1/2 Option - Other widths are available (consult factory). Standard - Each zone is powered through a low pressure disc type air clutch, driven by clutch to clutch #50 roller chain loops from a right angle reducer located near the center of the conveyor. All drive components are enclosed for safety and dirt shielding. Standard - 6 x 2 x .180 (7 ga.) roll formed rails with structural angle cross bracing. All welded construction. Standard - Welded butt on one side. Standard - 2.50 dia. x .120 (11 ga.) steel with grease packed, sealed for life bearings and 11/16 hex axles on 4, 4-1/2, 6, 7-1/2 or 9 centers. Each roller fitted with 21 tooth #40 roller chain sprockets for roll to roll drive within zones. rollers are mounted 1-3/4 low. Option - Regreaseable bearings are available. Option - A frame with a 6 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side for a roller 1/4 high is available. Standard - To control product drift, brakes are included. Standard - #40 roller chain for rollers. #50 roller chain for clutches. Standard - Floor type on maximum 5-0 approx. centers for a conveying height of 17 thru 48 (6000# capacity). Standard - 58 RPM right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, fan cooled, 30 FPM, 1-1/2 HP. Option - Maximum 3 HP. Standard - 10-0 (5-0 drive section) for 4, 6, 7-1/2 or 9 roller centers. 9-9 (4-10-1/2 drive section) for 4-1/2 roller centers. Option - Intermediate lengths are available. Standard - 5-0 for maximum product length of 48 (for 4, 6, 7-1/2 or 9 roller centers). 4-10-1/2 for maximum product length of 58-1/2 (for 4-1/2 roller centers). Option - Variable in increments of roller centers. Minimum 36, except at drive, maximum 60 (minimum of three rollers under article). Standard - Air logic. Option - 17 minimum, 48 maximum. Option - Speeds 30 to 60 FPM. Option - Drive may be located at any zone location in length of conveyor within limitations of capacity calculations. Option - Conveyor may be used for empty pallet transport in the reverse mode with additional controls. Option - As required (see Controls section).
DRIVE
CONVEYOR SECTION COUPLINGS CARRYING ROLLERS
ROLLERS HIGH
LENGTHS
ZONE LENGTHS
HB-828 - 12/03
Conveyor Capacity Calculations (CFC III)

(A) For conveyors with the drive at or near the center of the conveyor, limit the maximum number of zones per conveyor to the lesser of: 33, 000 x HP x ( Z one Length + Pallet Length ) Zones Conveyor = --------------------------------------------------------------------------------------------------------------------------------------------------- 0.0625 x Speed x Zone Length xM aximumLoa d Zone 1750 x ( Zone Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------0.039 xZone Length x M aximum Load Zone (31 Zones Maximum Recommended) (B) For conveyors with the drive at either end of the conveyor, limit the maximum number of zones per conveyor to the lesser of: 33, 000 x HP x ( Z one Length + Pallet Length ) Zones Conveyor = --------------------------------------------------------------------------------------------------------------------------------------------------- 0.0625 x Speed x Zone Length xM aximumLoa d Zone 875 x ( Zone Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------0.039 xZone Length x M aximum Load Zone (15 Zones Maximum Recommended) Note: For Maximum Load/Zone, add 9 lbs. for each roller in the zone, less 1/2 lb. for each 3 that the W is less than 39 HP = Output Horsepower, see table in the Engineering Data section, Dead Loads topic. Speed = Conveyor Speed in FPM Length = Length in feet (C) Zone Loading Maximum Allowable Load (lbs.) per Zone per Given Pallet Length. Based on Roller Capacities 24 Pallet Length 2380 2350 2170 1190 1180 1080 DO NOT USE 30 Pallet Length 2380 2350 2170 1780 1770 1630 1190 1180 1090 36 Pallet Length 3000 3000 3000 2380 2350 2170 1190 1180 1090 42 Pallet Length 3000 3000 3000 2380 2350 2170 1790 1770 1630 48 Pallet Length 3000 3000 3000 3000 3000 2720 2380 2350 2170
Roller Centers
Between Frames Up to 48
54 60 48
54 60 48
7-1/2
54 60
For additional data or for placing an order, please contact your local Field Sales Office.
HB-828 - 12/03
Extra Heavy Duty CFC Series IV - (3.50 dia. Rollers)
Basic Data 1 2 3 4 Intermediate Drive Section Conveyor Section Motor/Reducer, HP as required at 44 RPM 12,000# capacity Floor Supports
HB-828 - 12/03
Standard - 6000 lbs. maximum, 50 lbs. minimum per zone. Standard - 18 thru 78 Between Frame in 3 increments. Effective Conveying Width = W - 3-3/4. Recommended Effective Width should be Product Width + 3. Overall Width = W + 10. Option - Other widths are available (consult factory). Standard - Each zone is powered through a low pressure disc type air clutch, driven by clutch to clutch #60 roller chain loops from a right angle reducer located near the center of the conveyor. All drive components are enclosed for safety and dirt shielding. Standard - 7 x 2 x .180 (7 ga.) roll formed rails with structural angle cross bracing. All welded construction. Standard - Welded butt on one side. Standard - 3.50 dia. x .300 wall steel with grease packed, sealed for life bearings and 1-1/16 hex axles on 6, 7-1/2 or 9 centers. Each roller fitted with 20 tooth #60 roller chain sprockets for roll to roll drive within zones. Rollers are mounted 1-3/4 low. Option - Regreaseable bearings are available. Option - A frame with a 7 x 2 x .180 (7 ga.) formed steel channel on the chain side and a 5 x 2 x .180 (7 ga.) formed steel channel on the opposite side for a roller 1/4 high is available. Standard - to control product drift, brakes are included. Standard - #60 roller chain for rollers and for clutches. Standard - Floor type on maximum 5-0 centers for a conveying height of 18 thru 48 (12,000# capacity). Standard - 44 RPM right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, fan cooled, 30 FPM, 1-1/2 HP. Option - Maximum 3 HP. Standard - 10-0 (5-0 drive section). Option - Intermediate lengths are available. Standard - 5-0 (for maximum product length of 48). Option - Variable in increments of roller centers. Minimum 42, except at drive, maximum 60 (minimum of three rollers under article). Standard - Air logic. Option - 18 minimum, 48 maximum. Option - speeds 30 to 60 FPM. Option - Drive may be located at any zone location in length of conveyor within limitations of capacity calculations. Option - Conveyor may be used for empty pallet transport in the reverse mode with additional controls. Option - As required (see Controls section).
DRIVE
CONVEYOR SECTION COUPLINGS CARRYING ROLLERS
ROLLERS HIGH
LENGTHS ZONE LENGTHS
HB-828 - 12/03
Conveyor Capacity Calculations (CFC IV)

(A) For conveyors with the drive at or near the center of the conveyor, limit the maximum number of zones per conveyor to the lesser of: 33, 000 x HP x ( Z one Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------------------------------- 0. 0625 x Speed x Zone Length xM aximumLoa d Zone 2400 x ( Zone Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------0.043 xZone Length x M aximum Load Zone (31 Zones Maximum Recommended) (B) For conveyors with the drive at either end of the conveyor, limit the maximum number of zones per conveyor to the lesser of: 33, 000 x HP x ( Z one Length + Pallet Length ) Zones Conveyor = --------------------------------------------------------------------------------------------------------------------------------------------------- 0.0625 x Speed x Zone Length xM aximumLoa d Zone 1200 x ( Zone Length + Pallet Length ) Zones Conveyor = -------------------------------------------------------------------------------------------------------------------------0.043 xZone Length x M aximum Load Zone (15 Zones Maximum Recommended) Note: For Maximum Load/Zone, add 9 lbs. for each roller in the zone, less 1/2 lb. for each 3 that the W is less than 39 HP = Output Horsepower, see table in the Engineering Data section, Dead Loads topic. Speed = Conveyor Speed in FPM Length = Length in feet (C) Zone Loading Maximum Allowable Load (lbs.) per zone per given Pallet Length. Based on Roller Capacities 24 Pallet Length 4920 4880 4850 DO NOT USE DO NOT USE 30 Pallet Length 6000 6000 6000 4920 4880 4850 DO NOT USE 36 Pallet Length 6000 6000 6000 4920 4880 4850 4920 4880 4850 42 Pallet Length 6000 6000 6000 6000 6000 6000 4920 4880 4850 48 Pallet Length 6000 6000 6000 6000 6000 6000 6000 6000 6000
Roller Centers
Between Frames Up to 48
54 60 48
7-1/2
54 60 48
54 60
For additional data or for placing an order, please contact your local field sales office.
HB-828 - 12/03
Components
CFC Series II - Drive Section (1.90 dia. Rollers)
HB-828 - 12/03
Standard - 12 thru 63 Between Frames in 3 increments. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on chain box side. 5 x 2 x .180 (7 ga.) formed steel channel on side opposite chain box. Standard - 5-0 (24 min. thru 60 max.) for 4 roller centers. 5-0 (30 min. thru 60 max.) for 6 roller centers. 4-8 (40 min. thru 56 max.) for 8 roller centers. Standard - Welded butt. Standard - 4, 6 or 8 centers. Standard - 1.90 dia. x .109 (12 ga.) steel rollers with grease packed, sealed for life bearings and 7/16 hex axles. Two (2) 40A17 sprockets welded to each roller. Option - Regreaseable bearings are available. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side. 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Standard - To control product drift, brakes are included. Standard - #40 roller chain for rollers and #40 roller chain for clutches. Standard - Fully enclosed scalloped chain guard for rollers and fully enclosed guard for clutches. Standard - 58 RPM right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, fan cooled, 1-1/2 HP. Standard - Air logic. Standard - Drive may be located at any zone location in the length of the conveyor within limitations of capacity calculations (see Unit section for calculations). Standard - Speeds 30 to 60 FPM.
ZONE LENGTHS
ROLLERS HIGH BRAKE CHAIN CHAIN COVER MOTOR/REDUCER CONTROL DRIVE LOCATION
SPEED CHANGES
For additional data or placing an order, please contact your local Field Sales Office.
HB-828 - 12/03
CFC Series II - Intermediate Conveyor Section (1.90 dia. Rollers)
HB-828 - 12/03
Standard - 12 thru 63 Between Frames in 3 increments. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on chain box side. 5 x 2 x .180 (7 ga.) formed steel channel on side opposite chain box. Standard - 5-0 (24 min. thru 60 max.) for 4 roller centers. 5-0 (30 min. thru 60 max.) for 6 roller centers. 4-8 (40 min. thru 56 max.) for 8 roller centers. Standard - Welded butt on both sides. Standard - 4, 6 or 8 centers. Standard - 1.90 dia. x .109 (12 ga.) steel rollers with grease packed, sealed for life bearings and 7/16 hex axles. Two (2) 40A17 sprockets welded to each roller. Option - Regreaseable bearings are available. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side. 4 x 2 x .180 (7 ga.) formed steel channel on opposite side. Standard - #40 roller chain for rollers and #40 roller chain for clutches. Standard - Fully enclosed scalloped chain guard for rollers and fully enclosed guard for clutches.
ZONE LENGTHS
ROLLERS HIGH (One Side) CHAIN CHAIN COVER
HB-828 - 12/03
Heavy Duty CFC Series III - Drive Section (2.50 dia. Rollers)
HB-828 - 12/03
CONVEYOR WIDTH FRAME ZONE LENGTHS
Standard - 18 thru 72 Between Frames in 3 increments. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - 5-0 (36 min.-60 max.) for 4 roller centers. 4-10-1/2 (36 min. - 58-1/2 max.) for 4-1/2 roller centers 5-0 (42 min.-60 max.) for \6 or 9 roller centers. 5-0 (45 and 60) for 7-1/2 roller centers. Standard - Welded butt on side opposite chain guard. Standard - 4, 4-1/2, 6, 7-1/2 or 9 centers. Standard - 2.50 dia. x .120 (11 ga.) steel rollers with grease packed, sealed for life bearings and 11/16 hex axles. Two (2) 40A21 sprockets welded to each roller. Option - Regreaseable bearings are available. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side. 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Standard - To control product drift, brakes are included. Standard - #40 roller chain for rollers and #50 roller chain for clutches. Standard - Fully enclosed scalloped chain guard for rollers and fully enclosed guard for clutches. Standard - 58 RPM right angle reducer, 3 phase, 60 hertz, 230/460 volt, totally enclosed motor, fan cooled, 1-1/2 HP. Standard - Air logic. Standard - Drive may be located at any zone location in the length of the conveyor within limitations of capacity calculations (see Unit section for calculations). Standard - speeds 30 to 60 FPM.
SPEED CHANGES
HB-828 - 12/03
Heavy Duty CFC Series III - Intermediate Conveyor Section (2.50 dia. Rollers)
HB-828 - 12/03
Standard - 18 thru 72 Between Frames in 3 increments. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - 5-0 (48 min.-60 max.) for 4 or 6 roller centers. 4-10-1/2 (49-1/2 min. - 58-1/2 max.) for 4-1/2 roller centers 5-0 (52-1/2 min.-60 max.) for 7-1/2 roller centers. 5-0 (51 and 60) for 9 roller centers. Standard - Welded butt on side opposite chain guard. Standard - 4, 4-1/2, 6, 7-1/2 or 9 centers. Standard - 2.50 dia. x .120 (11 ga.) steel rollers with grease packed, sealed for life bearings and 11/16 hex axles. Two (2) 40A21 sprockets welded to each roller. Option - Regreaseable bearings are available. Standard - 6 x 2 x .180 (7 ga.) formed steel channel on the chain side. 4 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Standard - #40 roller chain for rollers and #50 roller chain for clutches. Standard - Fully enclosed scalloped chain guard for rollers and fully enclosed guard for clutches.
ROLLERS HIGH CHAIN CHAIN COVER
HB-828 - 12/03
Extra Heavy Duty CFC Series IV - Drive Section (3.50 dia. Rollers)
HB-828 - 12/03
Standard - 18 thru 78 Between Frame in 3 increments. Standard - 7 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - 5-0 (48 min. thru 60 max.) for 6 roller centers. 5-0 (52-1/2 min. thru 60 max.) for 7-1/2 roller centers. 5-0 (51 min. thru 60 max.) for 9 roller centers. Standard - Welded butt on side opposite chain guard. Standard - 6, 7-1/2 or 9 centers. Standard - 3.50 dia. x .300 wall steel with grease packed, sealed for life bearings and 1-1/16 hex axles. Two (2) 60A20 sprockets welded to each roller. Option - Regreaseable bearings are available. Standard - 7 x 2 x .180 (7 ga.) formed steel channel on the chain side. 5 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Standard - To control product drift, brakes are included. Standard - #60 roller chain for rollers and for clutches. Standard - Fully enclosed scalloped chain guard for rollers and fully enclosed guard for clutches. Standard - 44 RPM right angle reducer, 3 phase, 60 hertz, 230/460 volts, totally enclosed motor, fan cooled, 1-1/2 HP. Standard - Air logic. Standard - Drive may be located at any zone location in the length of the conveyor within limitations of capacity calculations (see Unit section calculations). Standard - Speeds 30 to 60 FPM.
SPEED CHANGES
HB-828 - 12/03
Extra Heavy Duty CFC Series IV - Intermediate Conveyor Section (3.50 dia. Rollers)
CONVEYOR WIDTH FRAME ZONE LENGTHS COUPLINGS ROLLER SPACING ROLLERS
Standard - 18 thru 78 Between Frames in 3 increments. Standard - 7 x 2 x .180 (7 ga.) formed steel channel on both sides. Standard - 5-0 (42 min. thru 60 max.) for 6 or 9 roller centers. 5-0 (45 min. thru 60 max.) for 7-1/2 roller centers. Standard - Welded butt on side opposite chain guard. Standard - 6, 7-1/2 or 9 centers. Standard - 3.50 dia. x .300 wall steel with grease packed, sealed for life bearings and 1-1/16 hex axles. Two (2) 60A20 sprockets welded to each roller. Option - Regreaseable bearings are available. Standard - 7 x 2 x .180 (7 ga.) formed steel channel on the chain side. 5 x 2 x .180 (7 ga.) formed steel channel on the opposite side. Standard - #60 roller chain for rollers and for clutches. Standard - Fully enclosed scalloped chain guard for rollers and fully enclosed guard for clutches.
ROLLERS HIGH CHAIN CHAIN COVER
HB-828 - 12/03
Supports
Supports
C1230 Floor Single Leg Floor Support - 750 Pound Capacity C1231 Floor Support - 1500 Pound Capacity
HOW TO ORDER Description Single Leg Double Leg 1 1 Quantity Code No. C1230 C1231 SL* 21 W Nominal Height 28 34 Knee Brace (if required) KB KB
*SL denotes single leg
Nominal Heights 2-1/8, 1-1/2 Adjustment
HB-828 - 12/03
Supports - 103
Supports
Standard widths 6 to 51 Between Frames in 3 increments. Heights range from 5/8 to 127 maximum. Use (1) 3/8 diameter anchor bolt per support foot. Sway bracing standard above 72 nominal height. OPTIONS Knee braces are available for supports with a nominal height over 16. (Add KB on How To Order). For single leg supports, specify C1230 floor support on How To Order. Single leg support has a maximum capacity of 750 pounds.
Supports - 104
HB-828 - 12/03
Supports
SUPPORT SELECTION TABLE Nominal Height 2-1/8 5-1/2 7-3/4 11-1/2 13 16 19 22 25 28 31 34 37 40 43 46 49 52 55 58 61 64 67 70 73 76 79 82 85 88 91 94 97 100 103 106 109 112 115 118 121 124 Minimum Height 5/8 4 5-1/2 10 11-1/2 13 16 19 22 25 28 31 34 37 40 43 46 49 52 55 58 61 64 67 70 73 76 79 82 85 88 91 94 97 100 103 106 109 112 115 118 121 Maximum Height 3-5/8 7 10 13 14-1/2 19 22 25 28 31 34 37 40 43 46 49 52 55 58 61 64 67 70 73 76 79 82 85 88 91 94 97 100 103 106 109 112 115 118 121 124 127 Adjustment 3 3 4-1/2 3 3 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Cross Brace 0 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
Available in 1-1/2 increments.
HB-828 - 12/03
Supports - 105
Supports
C681, C682, C683 and C684 Series - 3000 Pound Capacity Floor Supports
HOW TO ORDER Description Double Leg Quantity 7 Code No. C684 W 33 Nominal Height 43
WIDTHS HEIGHTS KNEE BRACES
Standard - 6 through 51 Between Frames. Standard - 3 to 119 maximum. Standard - Knee braces are standard at 23 nominal height and above.
Use (1) 3/8 diameter anchor bolt per support foot.
Supports - 106
HB-828 - 12/03
Supports
SUPPORT SELECTION TABLE Code No. C683 C682 Nominal Height 3 4 5 6 8 9 11 12 13 14 16 17 19 C681 20 22 *23 25 26 28 29 31 32 34 35 37 38 40 41 43 C684 44 46 47 49 50 52 53 55 56 58 59 Minimum Height 2-3/4 3-3/4 4-3/4 5-1/2 7 8-1/2 10 11-1/2 11-1/2 13 14-1/2 16 17-1/2 19 20-1/2 22 23-1/2 25 26-1/2 28 29-1/2 31 32-1/2 34 35-1/2 37 38-1/2 40 41-1/2 43 44-1/2 46 47-1/2 49 50-1/2 52 53-1/2 55 56-1/2 58 Maximum Height 3-3/4 4-3/4 5-3/4 7 8-1/2 10 11-1/2 13 14-1/2 16 17-1/2 19 20-1/2 22 23-1/2 25 26 28 29-1/2 31 32-1/2 34 35-1/2 37 38-1/2 40 41-1/2 43 44-1/2 46 47-1/2 49 50-1/2 52 53-1/2 55 56-1/2 58 59-1/2 61 Adjustment 1 1 1 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 Cross Brace 0 0 0 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3
HB-828 - 12/03
Supports - 107
Supports
SUPPORT SELECTION TABLE Code No. Nominal Height 61 62 64 65 67 68 70 71 73 76 77 79 80 82 83 85 86 88 89 C684 91 92 94 95 97 98 100 101 103 104 106 107 109 110 112 113 115 116 118 119 Minimum Height 59-1/2 61 62-1/2 64 65-1/2 67 68-1/2 70 71-1/2 74-1/2 76 77-1/2 79 80-1/2 82 83-1/2 85 86-1/2 88 89-1/2 91 92-1/2 94 95-1/2 97 98-1/2 100 101-1/2 103 104-1/2 106 107-1/2 109 110-1/2 112 113-1/2 115 116-1/2 118 Maximum Height 62-1/2 64 65-1/2 67 68-1/2 70 71-1/2 73 74-1/2 77-1/2 79 80-1/2 82 83-1/2 85 86-1/2 88 89-1/2 91 92-1/2 94 95-1/2 97 98-1/2 100 101-1/2 103 104-1/2 106 107-1/2 109 110-1/2 112 113-1/2 115 116-1/2 118 119-1/2 121 Adjustment 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Cross Brace
Note: *Knee braces included in price on nominal heights 23 and up.
Supports - 108
HB-828 - 12/03
Supports
C698 and C699 Series - 6000 pound capacity Floor Supports

HOW TO ORDER Quantity 3 Code No. C699 W 33 Nominal Height 25 Frame Rail Size 6 X 2 X .180 Channel
Nominal Heights 6-1/8 to 10-3/4, 1/2 Adjustment
Nominal Heights 13 to 71 in 2 increments, 1 Adjustment
WIDTH HEIGHTQ KNEE BRACES
Standard - 18 thru 60 Between Frames. Standard - 6-1/8 minimum to 71 maximum. Standard - Knee braces are standard at 19 nominal height and above.
Use (1) 1/2 diameter anchor bolt per support foot. Conveyor fame rail size is required to determine length of support top angle.
HB-828 - 12/03
Supports - 109
Supports
SUPPORT SELECTION TABLE Code No. Nominal Height 6-1/8 C698 7-1/8 8-5/8 9-3/4 10-3/4 13 15 17 19 21 23 25 27 29 31 33 35 37 C699 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 Minimum Height 5-5/8 6-5/8 8-1/8 9-1/4 10-1/4 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 Maximum Height 6-5/8 7-5/8 9-1/8 10-1/4 11-1/4 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 Adjustment 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Cross Brace 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3
Supports - 110
HB-828 - 12/03
Supports
C1570 - Floor Support - 12,000 or 25,000 Pound Capacity (Formerly E-609)

HOW TO ORDER Quantity 4 Code No. C1570 W 45 Nominal Height 24 Frame Rail Type LR Capacity 12,000#
Nominal height is fixed. Frame rail size is required in How To Order so the hole location in the support will match that of the frame rail.
12,000# Capacity A B C D For Types II and IV Only. HB-828 - 12/03 5 at 6.7# Channel 5 at 6.7# Channel 5 x 3-1/2 x 5/16 Angle 3 at 4.1# Channel
25,000# Capacity 8 at 11.5# Channel 8 at 11.5 Channel 6 x 4 x 1/2 Angle 4 at 5.4# Channel
Supports - 111
Supports
C1275 - Hanger Support - 1500 Pound Capacity For use with Single Strand Chain Driven Live Roller Conveyor
HOW TO ORDER Quantity 6 Code No. C1275 W 21 X Dim. 2-1/2 Y Dim. 2-1/2 Height XL Options SP
Supports - 112
HB-828 - 12/03
Supports
HB-828 - 12/03
Supports - 113
Supports
WIDTHS VERTICAL MEMBERS
Standard - 12 through 39 Between Frames in 3 increments. Standard - 2-1/2 x 1 x .109 (12 ga.) formed channel. Standard length is 10-0. Extra long length is 20-0 (add XL in How To Order). Maximum clearance between vertical members = W + X + Y + 1-1/2 = 63. Standard - 2.50 x .120 wall tubing. Standard - 5/8 dia. threaded rod, 2-3/4 adjustment. This support may be used for single or multiple decks. Maximum load capacity per deck is 1500# and maximum load capacity per support is 3000#. Attachments to overhead structures to be supplied by purchaser, and must be sufficient to develop the full capacity of the support. The following are optional and must be ordered separately: D2835 - Top Bracket (750# capacity each) D2834 - Cross member D2832 - Splice Coupling D921 - Brace To order additional hardware for second deck, order as C1275-W-XY-omit D2452 Drops. 1. Vertical members shipped in nominal 10-0 (std) or 20-0 (XL) lengths. Cut to proper length in the field. 2. All components shipped loose.
HORIZONTAL MEMBER ADJUSTING BOLT SPECIAL NOTE
NOTES
Supports - 114
HB-828 - 12/03
Accessories
Accessories
Model 3500TT - 90 Powered Turntable - 3000 Pound Capacity
HOW TO ORDER: Quantity 1 Code No. 3500TT Elevation Top of Roller 24 Speed 30 Voltage 460 Options ---
Designed to match RRCD250. 2.50 x 120 rollers on 4-1/2 centers. Effective conveying width of 50-1/4 (54 W), for 48 pallet. Top of roller elevation of 12-3/4, 16-1/4 to 18-1/4 and 19-1/4 to 48 maximum. 1/2 HP, 230/460 volt, 3 phase, brakemotor for 30, 40, 50 or 60 FPM. Air cylinder to provide 90 rotation (60 PSIG minimum required). 40 swing radius. Maximum three cycles per minute. Four 6 dia. caster wheels supporting 1/4 steel top plate. 2-position, 4-way air valve and filter-regulator-lubricator are required, but not included. Mountings for limit switches to sense home and rotated positions are included, but limit switches are optional. Factory wiring of motor, solenoid valve and limit switches to junction box is available as an option. Factory piping of cylinder and valve to a filter-regulator-lubricator is available as an option.
HB-828 - 12/03
Accessories - 115
Accessories
Model 3000XF - Two Strand Chain Transfer - 3000 Pounds Capacity For use with RRCD250 and RRCD256 CDLR
HOW TO ORDER: Quantity 1 Code No. 3000XF W 54 Transfer Speed 40 Voltage 230 Elevation T.O.R. 36 Options ---
BETWEEN FRAME STYLE
Note:This uNit is designed for use with a modified tread section 58.50 long, with spacing between rollers to accommodate the cross chain tracks on 30 centers. If matching 2.50 (C20010) use section C20102 If matching 2.50 (C20011) use section C20103 If matching 2.56 (C20020) use section C20105 If matching 2.56 (C20021) use section C20106 For ordering tread sections, see Components section.
Accessories - 116
HB-828 - 12/03
Accessories
For use with modified RRCD250 or RCD256 with Between Frame dimensions of 54 to 72 in 3 increments with rollers high on one side. See Note on previous page. Conveyor section not included. Two strands of #2060 extended pitch precision roller chain on 30 centers riding on extruded Hyfax chain guides. Transfer speeds of 30, 40, 50 and 60 FPM available. The chain transfer is powered by a 1/2 HP, 230/460 volt, 3-phase, totally enclosed gearmotor. Support structure included for transfer device. Conveyor section would be drive by adjoining conveyor. Air pressure required is 80 PSIG at device. 2-position, 3-way valve is needed but not included. Filter-regulator-lubricator is needed but not included. Mountings for limit switches to sense up and down positions are included, but limit switch are not included. Factory wiring of motor, solenoid valve and limit switches to junction box is available as an option. Factory piping of lifting device and valve to a filter-regulator-lubricator is available as an option.
HB-828 - 12/03
Accessories - 117
Accessories
Model 3100XF - Two Strand Chain Transfer - 3000 Pounds Capacity For use with RRCD250 and RRCD256 CDLR
HOW TO ORDER: Quantity 1 Code No. 3100XF W-1 54 Space 6 W-2 54 Transfer Speed 40 Motor Voltage 230 Elevation T.O.R. 27 Options ---
THROUGH FRAME STYLE
Contact factory for application assistance.
Accessories - 118
HB-828 - 12/03
Accessories
For use with modified RRCD250 or RRCD256 with Between frame dimensions of 45 to 60 in 3 increments with rollers high on one side (frame must be modified for chains). Conveyor section not included. Two strains of #2060 extended pitch precision roller chain on 30 centers riding on extruded Hyfax chain guides. Transfer speeds of 30, 40, 50 and 60 FPM available. The chain transfer is powered by a 1/2 HP, 230/460 volt, 3 phase, totally enclosed gearmotor. Support structure included for transfer device. Conveyor section would be driven by adjoining conveyor. Air pressure required is 80 PSIG at device. 2-position, 3-way valve is needed but not included. Filter-regulator-lubricator is needed but not included. Mountings for limit switches to sense up and down positions are included, but limit switches are not included. Factory wiring of motor, solenoid valve and limit switches to junction box is available as a option. Factory piping of lifting device and valve to a filter-regulator-lubricator is available as an option.
HB-828 - 12/03
Accessories - 119
Accessories
D1443 - Angle Guard Rail For use with Single Strand Chain Driven Live Roller Conveyor
HOW TO ORDER: Quantity 1 Code no. D1443 Height 3 Length 120
Standard length 10-0. Odd length cut in field. Galvanized finish standard. D1443 guard includes 1 rail only. None required on opposite side due to chain box.
Accessories - 120
HB-828 - 12/03
Accessories
D1444 - Curved Angle Guard Rail For use with C557 Curves
HOW TO ORDER: Quantity 1 Code no. C1444 W 29 Angle 90
Includes outside guard only. None required on inside rail due to chain box. Will match with D1443 angle guards. Galvanized finish standard. For 90 curves, 35 and 41 Between Frames, guard rails will be made in two 45 segments. Guards match radii of curves with standard 17, 23, 29, 35 and 41 Between Frames dimension only.
HB-828 - 12/03
Accessories - 121
Accessories
Accessories - 122
HB-828 - 12/03
Electrical Components & Control Equipment

NON-REVERSING TYPE MANUAL STARTERS NEMA 1 PHOTOCELL AND REFLECTOR (Less Mounting Brackets)
Wt. CE-4 Single Phase 2# CE-5 Three Phase 5#
Wt. Without Time Delay Relay 2# With Time Delay Relay 2#
NON-REVERSING TYPE MAGNET STARTERS NEMA 1
REVERSING TYPE MAGNET STARTERS NEMA 1
CE-6 Single Phase CE-7 Three Phase Size 0 For Fractional or Integral Use 10# Two pushbutton stations included with each starter
Wt. 10#
Wt. CE-8 Single Phase 28# CE-9 Three Phase Size 0 For Fractional or Integral Use 28# Two pushbutton stations included with each starter
Combination Starters
As the name implies, combination starters put together in one enclosure an externally operable disconnect switch, fuses and either a reversing or non-reversing magnetic starter. This form of control eliminates the field wiring required by the separate fused disconnect used with the standard version of magnetic starters. The combination starters are listed in both (NEMA 1) standard duty enclosures (NEMA 12) heavy duty, oil tight/dust tight industrial enclosures. Size 1 starters can handle a maximum of 71/2 HP at 200/230 volts and 10 HP at 460/575 volts. To supply the proper starter, both the operating voltage and horsepower of the motor must be furnished.
HB-828 - 12/03
Electrical Components & Control Equipment - 123
SIZE 1 COMBINATION STARTERS
NON-REVERSING CE-12 NEMA 1 CE12A NEMA 12
Wt. 35# 36#
REVERSING CE-13 NEM 1 CE-13A NEMA 12
Wt. 35# 36#
Standard voltages, which can be furnished, are 200, 230, 460 and 575. Above units are available with separate 120 volt operating coil, add suffix S. Transformers for other starter coils are available by adding suffix T. Above starters include two pushbutton stations.
HB-828 - 12/03
Components For Driving and Controlling the Powered Conveyors

This section deals with the components that drive and control powered conveyors. It presents a review of the various components used and information required to make the proper selection. These various control mechanisms can be used to control single units or be incorporated into systems.
Motors
There are three basic types of motor enclosures: 1. Open The motor windings can be seen through the vents at the end of the motor. 2. Totally Enclosed The motors are completely encased in a metal enclosure. 3. Explosion Proof The enclosure of the motor will withstand an explosion from within itself and will not allow sparks or hot gas to escape into the surrounding atmosphere. Explosion proof motors are further rated by class and group by the National Electric Code according to the environment in which they are designed to operate. Class I Hazardous Vapor Group C - Ethers, Alcohols, etc. Group D - Petroleum Base Hazardous Dust Group E - Metal Group F - Carbons Group G - Grains
Class II
There are three designations required when specifying the power source an A.C. motor is to operate from: 1. Phase - Three or One 2. Frequency - Hertz
3. Voltage - Volts Common single phase voltages are 115 and 230. Common three phase voltages are 208, 230, 460 and 575. Motors for 230 or 460 volt applications normally are supplied as dual voltage, (i.e. 230/460). When specifying motors, the single voltage which will be used to operate the motor must be stated if the proper controls for starting and stopping the motor are to be selected. Motors are commonly mounted by two principle means, foot mounted or C-face. Foot mounted is nothing more than a set of mounting feet which are welded or otherwise attached to the bottom of the motor. C-face mounting consists of a cast ring or collar on the end of the motor with four mounting holes which allows the motor to be attached to a reducer, machine, etc.
HB-828 - 12/03
Gear Reducer
A reducer is a device which converts a high RPM with low torque (usually supplied by a motor at the reducers input shaft) to a lower RPM with higher torque on the reducers output shaft, which is connected to the conveyor drive. Reducers are generally selected based on the amount of the horsepower to be transmitted and the amount of reduction in speed that is required. Terminology used in speed reduction is ratio. Ratio is the rate of the output speed as compared to the input speed. Typical ratios are 10:1, 40:1, etc. If an 1800 RPM motor is coupled to a 40:1 ratio reducer, the resultant output speed would be 1800 divided by 40 which equals 45 RPM Manufacturers rating tables are used to select a reducer with the proper horsepower rating. Gear reducers are generally grouped into two categories, parallel shaft and right angle shaft. The determination is made by the position of the output shaft relative to the input shaft. If the output shaft is in position parallel to the input shaft, then the gear reducer is termed a parallel reducer. If the output shaft is in a position forming a right angle to the input shaft, the reducer is termed a right angle reducer. The most common mounting arrangement for reducers is foot mounted. This consists of a set of feet, with holes in them, that are attached to the reducer. With this arrangement, the reducer can be bolted to any flat surface. Since the reducer requires oil to lubricate the gears, it is necessary to know whether it is intended to be mounted with the feet up and the reducer below, such as a ceiling hung mounting position or with the feet down and the reducer above them, which would be termed a floor mounted position. Another important consideration in gear reducers is how the motor will be attached to the reducer. One simple means is to foot mount the reducer and foot mount the motor at relative positions so that the output shaft of the motor is aligned with the input shaft of the reducer. A suitable coupling can then be used to connect the two. An alternative approach is to use a C-face motor and C-face reducer. Remember that a C-face motor has a ring or collar on the end of the motor with four mounting holes. Reducers can be purchased that have a corresponding collar around the input shaft of the reducer. A plastic collar couples the output shaft of the motor to the input shaft of the reducer and when the motor and reducer are bolted together, it encloses the coupling eliminating the need for a guard. Because of the popularity of C-face motor reducer combinations when they were originally introduced, manufacturers carried that concept forward with the introduction of the integral gearmotor. An integral gearmotor is a motor and reducer or gear box, cast into one housing. Basically, the motor is made open ended on the end next to the gear box and the gear box has a flat plate and collar to accept the motor. This eliminates the need for C-face rings on the motor and reducer and therefore is more economical. The disadvantages of the integral gearmotor is that if either the motor or reducer fails, both have to be replaced since it is an integral unit. In the case of a C-face motor and C-face reducer, if the motor fails, only the motor has to be replaced. If the reducer fails, only the reducer has to be replaced.
HB-828 - 12/03
Brakes
The most common types of brakes used with motors are spring set/electrically released type. This is a disc type brake, that when power to the motor is eliminated, a spring sets the brake to stop the rotation of the motor. When power is applied to the motor, the brake is released by an electrical solenoid. Brakes are sized in terms of the torque they produce. Normally, for a holding brake such as is used on a conveyor, a brake should be sized 3 ft. lbs. per horsepower or as an example, a 3 ft. lb. brake is used for a 1 horsepower motor and a 6 ft. lb. brake for a 2 horsepower motor.
Clutch Brake
A clutch-brake is a device that is mounted between the motor and the reducer. With a clutch-brake, the motor runs continuously. When the conveyor is to start, the clutch is energized and the brake is released. When it is desirable to stop the conveyor, the clutch is released and the brake is applied. Clutch-brakes require a special power supply and controlling device. This controller allows the force between the clutch discs and brake discs to be varied. This provides a means of adjusting the starting and stopping motions of the conveyor from soft to violent. Three phase motors with brakes generally can be started and stopped up to six times per minute. For applications requiring more starts and stops per minute, a clutch brake should be used.
Motor Starters Manual Motor Starters

Manual motor starters are devices which, when a button is pushed or a toggle type switch is thrown, operate a set of electrical contacts which supply power to a motor. The button or toggle switch is an integral part of the manual starter. Manual motor starters can be used when a conveyor is being controlled from one point only and can not be connected with any other remotely located control circuit devices, such as a second push button, a limit switch, or photoelectric relay. In order to select the proper manual motor starter, the following must be known: 1. Reversing or Non-Reversing 2. Single Phase or 3 Phase 3. Frequency of Power Supply (60 Hertz) 4. Voltage at which the motor is to be run (this must be one voltage, not dual voltage such as 230/ 460. 5. Horsepower of motor controlled by the starter.
Magnetic Motor Starters

Magnetic motor starters are used where it is desirable to control a conveyor from more than one location. Magnetic motor starters have basically two circuits associated with them. One is a control circuit and the other is a power circuit. The power circuit turns electrical line power to the motor off or on. The line power provides the energy for the motor to actually do work while the control circuit tells it when. The control circuit is controlled by push button, limit switches, photoelectric relays and switching devices. Technically, these switching devices are used to energize the magnetic coil of the starter which in turn operates a set of multiple contacts. These contacts are used to complete the power circuit to the motor. The control circuit voltage is usually lower than the power circuit voltage. In order to select the proper magnetic starter, the following must be known: 1. Reversing or Non-Reversing 2. Phase, frequency and voltage the motor is to run on (power voltage). HB-828 - 12/03 Electrical Components & Control Equipment - 127

3. Phase, frequency and voltage the push button is to be run on (control voltage) 4. Is a transformer required to change motor voltage to control voltage? (This would be required if, for instance, there was only one power source available, such as 230 volts, which is acceptable for the line power for the motor but the push buttons are desired to operate at 115 volts.) 5. Horsepower of the motor to be controlled.
Combination Magnetic Motor Starters and Control Panels

The National Electrical Code requires both short circuit protection and running overload protection for each motor in a conveyor system. In addition, a lockable disconnecting device must be provided with sight and (also) within 50 feet of each motor. The running overload protection for a motor is provided by the heaters in a starter. Heaters are an integral part of all motor starters. This leaves the problem of providing short circuit protection and a disconnecting means to consider. Providing a combination motor starter for each motor meets both of these requirements. The fuses or circuit breakers in a combination starter provide the short circuit protection and the disconnect or circuit breaker provides the disconnecting means. The circuit breakers provide the same function as a fused-disconnect. The only other requirement of this alternative to meeting the criteria of the National Electrical Code is physically locating the combination starters within 50 feet and in sight of the motors they control. Typically these starters are individually located directly beside the motor they control and are mounted on the side of the conveyor drive. A second alternative to meeting this requirement of the National Electrical Code is to provide across the line magnetic starters and provide a fused-disconnect in a separate enclosure. Typically the fused-disconnects are provided by whoever is doing the field wiring. Although this is typical it is an often misunderstood point. If across the line starters are provided by the equipment supplier, it should be established early in the development of a project whether the equipment supplier is also providing fuse-disconnects or whether they will be provided by the field wiring supplier. A third alternative to meeting the requirements of the National Electrical Code is providing a prewired control panel. The control panel houses across the line starters and fuses or circuit breakers for each motor in a common enclosure. This meets the short circuit protection requirement. The control panel includes a main disconnect switch which meets the disconnecting means requirement of the code as long as all of the motors are located within 50 feet and within sight of the control panel. If some of the motors are beyond a 50 foot radius of the panel or are not visible from the panel, then a non-fused disconnect must be provided for each motor. These disconnects are usually provided by the field wiring contractor but not always. Caution must be exercised between the parties involved in a project that everyone understands who is providing what. In summary, there are three essential parts to motor control: the disconnecting means, the overload heaters contained in the magnetic starter, and the short circuit protection. These can be grouped in various combinations in multiple or common enclosures.
HB-828 - 12/03
Electrical Enclosures
Standards for the manufacture of electrical control devices have been agreed on by the National Electrical Manufacturers Association or N.E.M.A. N.E.M.A. has established various classifications for enclosures or boxes enclosing push buttons, motor starters, photoelectric cells, etc. A numbering system is used to describe these enclosures, and the following are some of the more common that you will encounter. 1. N.E.M.A. Type 1 - Surface Mounting (General Purpose Sheet Metal) Type 1 enclosures are intended for indoor use, primarily to provide a degree of protection against contact with enclosed equipment in locations where usual service conditions do not exist. The enclosure is sheet metal and treated to resist corrosion. 2. N.E.M.A. Type 4 (Water Tight) Type 4 enclosures are intended for in-door or external use primarily to provide a degree of protection against wind blown dust and rain, splashing water, and hose directed water. They are designed to meet hosed down, dust, external icing and rust resistance design tests. They are not intended to provide protection against conditions such as internal condensation or internal icing. Enclosures are made of heavy gauge stainless steel, cast aluminum or heavy gauge sheet metal, depending upon the type of unit. The cover has a synthetic rubber gasket. 3. N.E.M.A. Type 7 and 9 (Explosion Proof) These enclosures are intended for indoor use. N.E.M.A. type 7 is normally used in atmospheres that contain hazardous gas and will be used in areas that correspond with Class 1, Group C and D motors. N.E.M.A. type 9 would normally be used in atmospheres that contain hazardous dust and would be used in conjunction with motors that are classified as Class II, Group E, F, and G. 4. N.E.M.A. 12 (Industrial Dust-Tight) These enclosures are intended for use indoors to protect the enclosed equipment against fibers, flying lint, dust and dirt and light splashing, seepage, dripping and external condensation of noncorrosive liquids.
Switching Devices Push Buttons

Push buttons are about the simplest switching device known. The operator simply pushes a button which causes an electrical contact to close, thus providing a signal for something else to happen.
Limit Switches
Limit switches are switching devices which are actuated by a machine motion striking a lever on the switch. The lever causes an electrical contact to operate which causes some other action to happen.
Selector Switches
Selector switches are similar to a push button except the operator rotates the switch as opposed to pushing down on the switch to cause an electrical contact to operate.
Photoelectric Relays
Photoelectric relays are a no touch switching device. This is a device which operates an electrical contact when a beam of light is broken.
HB-828 - 12/03
Solenoid Valves
A solenoid valve is an air or hydraulic valve combined with a solenoid. The solenoid is a magnetic coil which is turned on by a switching device or logic device. When the coil is turned on, it causes an armature to move and push a plunger in one direction or the other. The plunger and the solenoid shifts a spool in the valve to cause a different flow path for the air or hydraulic fluid.
Air Controls
Air control used on conveyors normally consist of valves and filter-regulators which may be used to raise and lower stops and transveyors or perhaps to actuate some other divert mechanism. A filter-regulator-lubricator is a combination of three devices. The filter cleans the dirt and grit out of the air, the regulator regulates the pressure in the air line and keeps it below a certain maximum pressure. The lubricator squirts oil into the air passing through it. This lubrication is used to lubricate the valve and cylinder which is normally connected to the filter-regulator-lubricator.
HB-828 - 12/03

Mathews Roller Conveyors

Uploaded by

Copyright:

Available Formats

Mathews Roller Conveyors

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mathews Roller Conveyors

Uploaded by

Copyright:

Available Formats

What are some components described in the document?

What are some components described in the document?

What is a solenoid valve?

What is a solenoid valve?

Chain Driven Live Roller Conveyor

Chain Pull and Horsepower Calculations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5

Single Strand CDLR

Product Width - Straight Conveyor

Product Width - Curves

Product Length - Straight Conveyor

Product Length - Curves

Chain Pull and Horsepower Calculations

Dead Load (B)

Chain Pull (C)

Effective Chain Pull

Total Chain Pull (C + D + E) x 1.25 = Eff. Chain Pull (lbs.)

Note: At higher speeds, noise level may be a consideration.

Roller to Roller CDLR

Product Width - Straight Conveyor

Product Width - Curves

( Radius + Package Width )

Package Length --------------------------------------------- ( Radius 2 ) + 2

( 59.125 ) 2 + ( 12 ) 2 33.125 3496 + 144 33.1 3640 33.1

Product Length - Straight Conveyor

Product Length - Curves

Chain Pull and Horsepower Calculations

Chain Pull Calculations

Single Strand CDLR

Single Strand CDLR

Single Strand CDLR - 17

Single Strain CDLR

CONVEYOR WIDTH DRIVE END ROLLER CONVEYOR SECTION

COUPLINGS CARRYING ROLLERS

MOTOR / REDUCER LENGTHS SIDE GUARDS ELECTRICAL CONTROLS

Single Strand CDLR - 18

Single Strand CDLR

End Drive - Model LRSC

Note: See the C557 Curve topic in this section

Single Strain CDLR

CAPACITY CONVEYOR WIDTH DRIVE END ROLLER CURVED CONVEYOR SECTION

COUPLINGS CARRYING ROLLERS

MOTOR / REDUCER SIDE GUARDS ELECTRICAL CONTROLS

Single Strand CDLR - 20

Single Strand CDLR

Single Strand CDLR - 21

Single Strain CDLR

CAPACITY CONVEYOR WIDTH DRIVE FRAME

CHAIN CHAIN COVER

Single Strand CDLR - 22

Single Strand CDLR

C573 End Drive

Single Strand CDLR - 23

Single Strain CDLR

CAPACITY CONVEYOR WIDTH DRIVE

COUPLINGS ROLLERS CHAIN CHAIN COVER

Single Strand CDLR - 24

Single Strand CDLR

C559 End Drive

CAPACITY CONVEYOR WIDTH DRIVE

COUPLINGS ROLLERS CHAIN COVER