Dr.

NNCE

MECH/IV SEM

SOM LAB -LM

ME2256 STRENGTH OF MATERIALS LABORATORY MANUAL

FOR FOURTH SEMESTER B.E MECHANICAL ENGG Academic Year-2013-2014 (FOR PRIVATE CIRCULATION ONLY) ANNA UNIVERSITY -CHENNAI

NAME REG NO BATCH

: : :

DEPARTMENT OF MECHANICAL ENGINEERING

Dr. NAVALAR NEDUNCHEZHIYAN COLLEGE OF ENGINEERING THOLUDUR- 606303, CUDDALORE DIST.

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

UNIVERSITY PRACTICAL EXAMINATION Allotment of Marks

Internal Assessment Practical Examination = 20 marks = 80 marks

INTERNAL ASSESSMENT [20 Marks]

Staff should maintain the assessment Register and the Head of the Department should monitor it.

SPLIT UP OF INTERNAL MARKS

Record Note = 10 marks Model Exam = 5 marks Attendance = 5 marks __________ Total 20 marks ___________

UNIVERSITY EXAMINATION
The examination will be conducted for 100 marks. Then the marks will be calculated to 80 marks.

Split up of Practical Examination Marks

Aim and Procedure Tabulation = 25 marks = 15 marks

Formulae and Calculation = 30 marks Graph and Result Viva Voce = 20 marks = 10 marks ___________ Total = 100 marks ___________

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

GENERAL INSTRUCTIONS FOR LABORATORY CLASSES Enter Lab with CLOSED FOOTWEAR Boys should TUCK IN the shirts Students should wear uniform only LONG HAIR should be protected, let it not be loose especially near ROTATING MACHINERY. Any other machines/ equipments should not be operated other than the prescribed one for that day. POWER SUPPLY to your test table should be obtained only through the LAB TECHNICIAN Do not LEAN and do not be CLOSE to the rotating components. TOOLS, APPARATUS & GUAGE Sets are to be returned before leaving the Lab. HEADINGS & DETAILS should be neatly written 1. Aim of the experiment 2. Apparatus / Tools/ Instruments required 3. Procedure / Theory / Algorithm / Program 4. Model Calculations 5. Neat Diagram/ Flow charts 6. Specifications/ Designs details 7. Tabulation 8. Graph 9. Result/ Discussions Before doing the experiment, the student should get the circuit/ Program approval by the FACULTY-IN-CHARGE Experiment date should be written in the appropriate place After completing the experiments, the answer to the VIVA-VOCE Questions should be neatly written in the workbook Be PATIENT, STEADY, SYSTEMATIC, & REGULAR

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

SYLLABUS ME2256 STRENGTH OF MATERIALS LABORATORY

LTPC 0032 LIST OF EXPERIMENTS 1. Tension test on a mild steel rod. 2. Double shear test on Mild steel and Aluminium rods. 3. Torsion test on mild steel rod. 4. Impact test on metal specimen. 5. Hardness test on metals - Brinnell and Rockwell Hardness Number. 6. Deflection test on beams. 7. Compression test on helical springs. 8. Strain Measurement using Rosette strain gauge. 9. Effect of hardening- Improvement in hardness and impact resistance of steels. 10. Tempering- Improvement Mechanical properties Comparison (i) Unhardened specimen (ii) Quenched Specimen and (iii) Quenched and tempered specimen. 11. Microscopic Examination of Hardened samples and (ii) Hardened and tempered samples. Total: 45

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

CONTENTS

S.NO

NAME OF EXPERIMENTS

PAGE No.

1. 2. 3. 4. 5. 6. 7. 8. 9.

To study the brinell hardness testing machine & perform the brinell hardness test. To study the rockwell hardness testing machine & perform the rockwell hardness test. To study the impact testing machine and perform the impact Test(Izod test) To study the impact testing machine and perform the impact Tests(Charpy test) To study the universal testing machine and perform the tensile test. To perform double shear test on given specimen. To perform compression test on open coil spring. To perform torsion test on mild steel. To perform deflection on beam.

6 9 12 16 19 23 25 28 31

Beyond the syllabus

10. 11. To examine the microstructure of a given plain carbon steel. To perform brinell hardness test in a tempered material.

34 36

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 1
Title of the Experiment: - To study the brinell hardness testing machine & perform the brinell hardness test. Date of the Experiment:STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To study the Brinell hardness testing machine and the Brinell hardness test. STEP 2: FACILITIES REQUIRED AND PROCEDURE a) Facilities required to do the experiment:S.No. 1 Facilities required Brinell Hardness Quantity 1

testing machine 2 Specimen of mild steel / cast iron/ non ferrous metals Brinell microscope 1

b.)Theory: - Hardness represents the resistance of material surface to abrasion, scratching and cutting, hardness after gives clear identification of strength. In all hardness testes, a define force is mechanically applied on the test piece for about 15 seconds. The indentor, which transmits the load to the test piece, varies in size and shape for different tests. Common indenters are made of hardened steel or diamond. In Brinell hardness testing, steel balls are used as indentor. Diameter of the indentor and the applied force depend upon the thickness of the test specimen, because for accurate results, depth of indentation should be less than 1/8 of the thickness of the test pieces. According to the thickness of the test piece increase, the diameter of the indentor and force are changed. c.)Specification of Hardness Testing machine and Indentors:A hardness test can be conducted on Brinell testing m/c, Rockwell hardness m/c or vicker testing m/c. the specimen may be a cylinder, cube, think or thin metallic sheet.Its specification are as follows: 1. Ability to determine hardness upto 500BHN. 2. Diameter of ball (as indentor) used D = 2.5mm, 5mm, 10mm. 3. Maximum application load = 3000kgf. 4. Method of load application = Lever type 5. Capability of testing the lower hardness range = 1 BHN on application of 0.5Dload d.)Procedure for doing the experiment:Step No. 1. 2. Details of the step Insert ball of dia D in ball holder of the m/c. Make the specimen surface clean by removing dust, dirt, oil and grease etc. 6

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

3. 4. 5. 6. 7. 8.

Make contact between the specimen surface and the ball by rotating the jack adjusting wheel. Push the required button for loading. Pull the load release level and wait for minimum 15 second. The load will automatically apply gradually Remove the specimen from support table and locate the indentation so made. View the indentation through microscope and measure the diameter d by micrometer fitted on microscope. Repeat the entire operation, 3-times.

e..)Tabulation:S.No. Ball Load applied P Diameter of P/D2 BHN Diameter in indentation in mm kgf. d (mm) 1.(M.S.) 10 3000 4.6 30 370.46 f.) Observation and Calculation: Area of indentation A=d/2(D-D2-d2) =4.6/2(10-102-4.62) =8.098 BHN = Load Applied (kgf.)/ Spherical surface area indentation (in mm.) =3000/8.098 =370.46

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

g.)Precautions:1. The specimen should be clean properly. 2. Take reading more carefully and correct. 3. Place the specimen properly. 4. Jack adjusting wheel move slowly 5. After applying load remove the load. h.)Result:The brinell hardness number of the given specimen are found out and tabulated.

VIVA QUESTIONS:1. Define buckling facto r and buckling load. Buckling factor: It is the ratio between the equivalent length of the column to the minimum radius of gyration. Buckling load : The maximum limiting load at which the column tends to have lateral displacement or tends to buckle is called buckling or crippling load. The buckling takes place about the axis having minimum radius of gyration, or least moment of inertia 2. Define safe load. It is the load to which a column is actually subjected to and is well below the buckling load. It is obtained b y dividing the buckling load by a suitable factor o f safety (F.O.S). Safe load = Buckling load /Factor of safety 3. State Hookes law. It states that when the material is loaded, within its elastic limit, the stress is directly proportional to the strain. Stress Strain 4. Define Factor of Safety. It is defined as the ratio of ultimate tensile stress to the permissible stress(working stress). 5. State the tensile stress & tensile strain. When a member is subjected to equal & opposite axial pulls the length of the member is increased. The stress is included at any cross section of the member is called Tensile stress & the corresponding strain is known as Tensile strain.

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 2
Title of the Experiment: To study the Rockwell Hardness testing machine and perform the Rockwell hardness test. Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To study the Rockwell Hardness testing machine and perform the Rockwell hardness test. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. 1 Facilities required Rockwell Hardness Quantity 1

testing machine Specimen of mild 1 steel / cast iron/ non ferrous metals b.)Theory: - Hardness represents the resistance of material surface to abrasion, scratching and cutting, hardness after gives clear indication of strength. In all hardness tests, a define force is mechanically applied on the piece, varies in size and shape for different tests. Common indentors are made of hardened steel or diamond. Rockwell hardness tester presents direct reading of hardness number on a dial provided with the m/c. principally this testing is similar to Brinell hardness testing. It differs only in diameter and material of the indentor and the applied force. Although there are many scales having different combinations of load and size of indentor but commonly C scale is used and hardness is presented as HRC. Here the indentor has a diamond cone at the tip and applied force is of 150 kgf. Soft materials are often tested in B scale with a 1.6mm dia. Steel indentor at 60kgf. c.)Specification of Hardness Testing machine and Indentors:A hardness test can be conducted can be conducted on Brinell testing m/c,Rockwell hardness m/c or vicker testing m/c. the specimen may be a cylinder, cube, thick or thin metallic sheet. d.)Procedure for doing the experiment:2 Step No. 1. 2. 3. 4. Details of the step Insert ball of dia D in ball holder of the m/c. Make the specimen surface clean by removing dust, dirt, oil and grease etc. Make contact between the specimen surface and the ball by rotating the jack adjusting wheel. Push the required button for loading.

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

5. 6. 7.

Pull the load release level and wait for minimum 15 second. The load will automatically apply gradually Remove the specimen from support table and locate the indentation so made. Repeat the entire operation, 3-times. Load in kg minor major 60 Dial reading 1 79 2 80 3 79 79 RHN

e.)Tabulation:S.No. Indentor

1.(AL.) Ball f.)Precautions:1. 2. 3. 4.

10

The specimen should be clean properly. Take reading more carefully and correct. Place the specimen properly. Jack adjusting wheel move slowly.

g.)Result:The rockwell hardness number of the given specimen are found out and tabulated.

10

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

VIVA QUESTIONS:1. Define Stress. When an external force acts on a body, it undergoes deformation. At the same time the body resists deformation. The magnitude of the resisting force is numerically equal to the applied force. This internal resisting force per unit area is called stress. 2. Define strain. When an external force acts on a body, there is some change of dimension in the body. Numerically the strain is equal to the ratio of change in length to the original length of the body. 3. Define Modulus of Elasticity. The ratio of tensile stress to the corresponding tensile strain is constant within its elastic limit. The ratio is known as Youngs Modulus or Modulus of Elasticity. 4. State Bulk Modulus. The ratio of direct stress to the corresponding volumetric strain is constant within elastic limit. The ratio is known as Bulk Modulus. 5. Define poisons ratio. When a body is stressed, within its elastic limit, the ratio of lateral strain to the longitudinal strain is constant for a given material.

11

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 3
Title of the Experiment: To study the Impact Testing m/c and Perform Izod impact test. Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To study the Impact Testing m/c and Perform Izod impact test. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. 1 2 3 4 Facilities required Impact testing m/c Izod test specimens of mild steel Vernier caliper Quantity 1 1 1

Specimen setting 1 fixture b.)Theory:-In manufacturing locomotive wheels, coins, connecting rods etc. the components are subjected to impact (shock) loads. These loads are applied suddenly. The stress induced in these components is many times more than the stress produced by gradual loading. Therefore, impact tests are performed to asses shock absorbing capacity of materials subjected to suddenly applied loads. These capabilities are expressed as (i) Rupture energy (ii) Modulus of rupture and (iii) Notch impact strength. Two types of notch impact tests are commonly- 1. Charpy test. 2. Izod test. In Izod test, the specimen is placed as cantilever beam. The specimens have V-shaped notch of 45. U-shaped notch is also common. The notch is located on tension side of specimen during impact loading. Depth of notch is generally taken as t.5 to t/3 wheret is thickness of the specimen. c.) Specification of machine and specimen details:Its specifications along-with their typical values are as follows: Impact capacity = 164joule Least count of capacity (dial) scale = 2joule Weight of striking hammer = 18.7 kg. Swing diameter of hammer = 1600mm. Angle of hammer before striking = 90 Distance between supports = 40mm. Striking velocity of hammer = 5.6m/sec. Specimen size = 75x10x10 mm. Type of notch = V-notch Angle of notch = 45 Depth of notch = 2 mm.

12

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

13

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

d.)Procedure for doing the experiment:Step No. 1. Details of the step Lift the hammer to an appropriate knife edge position and notch the energy stored in the hammer. For the standard Izod test the energy stored should be 164j. Locate the test specimen on the m/c supports. Release the hammer. The hammer will break the piece and shoot up the other side of the specimen. Note the residual energy indicated on the scale by the hammer.

2. 3. 4. 5.

Impact strength of the test specimen is the difference of the initial energy stored in hammer and the residual energy. e.)Tabulation:S.No. Initial Residual Absorb Energy Impact Energy (E1) Energy (E2) (E1-E2) strength in joule in joule in joule j/mm2 1. 2 83 300-82=216 21.6 f.) Observation and Calculation: Notch impact strength = Absorb energy / Effective cross section area =216/10 =21.6 j/mm2

14

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

g.)Precautions:1. The specimen should be prepared in proper dimensions. 2. Take reading more frequently. 3. Make the loose pointer in contact with the fixed pointer after setting the pendulum. 4. Do not stand in front of swinging hammer or releasing hammer. 5. Place the specimen proper position. h.)Result:The impact strength of given specimen = 21.6 j/mm2

VIVA QUESTIONS:1. Who postulated the theory of curved beam? Winkler-Bach postulated the theory of curved beam. 2. What is the shape of distribution of bending stress in a curved beam? The distribution of bending stress is hyperbolic in a curved beam. 3. Where does the neutral axis lie in a curved beam? The neutral axis does not coincide with the geometric axis. 4. What is the nature of stress in the inside section of a crane hook? Tensile stress 5. Where does the maximum stress in a ring under tension occur? The maximum stress in a ring under tension occurs along the line of action of load.

15

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 4
Title of the Experiment: To study the Impact Testing m/c and Perform charpy impact test. Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To study the Impact Testing m/c and Perform charpy impact test. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. 1 2 3 4 Facilities required Impact testing m/c charpy test specimens of mild steel Vernier caliper Quantity 1 1 1

Specimen setting 1 fixture b.)Theory:- In manufacturing locomotive wheels, coins, connecting rods etc. the components are subjected to impact (shock) loads. These loads are applied suddenly. The stress induced in these components is many times more than the stress produced by gradual loading. Therefore, impact tests are performed to asses shock absorbing capacity of materials subjected to suddenly applied loads. These capabilities are expressed as (i) Rupture energy (ii) Modulus of rupture and (iii) Notch impact strength. Two types of notch impact tests are commonly- 1. Charpy test 2. Izod test. In charpy test, the specimen is placed as cantilever beam. The specimens have V-shaped notch of 45.U-shaped notch is also common. The notch is located on tension side of specimen during impact loading. Depth of notch is generally taken as t.5 to t/3 where t is thickness of the specimen. c.) Specification of machine and specimen details:Its specifications along-with their typical values are as follows: Impact capacity = 300joule Least count of capacity (dial) scale = 2joule Weight of striking hammer = 18.7 kg. Swing diameter of hammer = 1600mm. Angle of hammer before striking = 160 Distance between supports = 40mm. Striking velocity of hammer = 5.6m/sec. Specimen size = 55x10x10 mm. Type of notch = V-notch Angle of notch = 45 Depth of notch = 2 mm.

16

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

d.)Procedure for doing the experiment:Step No. 1. Details of the step Lift the hammer to an appropriate knife edge position and notch the energy stored in the hammer. For the standard Izod test the energy stored should be 164j. Locate the test specimen on the m/c supports. Release the hammer. The hammer will break the piece and shoot up the other side of the specimen. Note the residual energy indicated on the scale by the hammer.

2. 3. 4. 5.

Impact strength of the test specimen is the difference of the initial energy stored in hammer and the residual energy. e.)Tabulation:S.No. Initial Residual Absorb Energy Impact Energy (E1) Energy (E2) (E1-E2) strength in joule in joule in joule j/mm2 1. 2 80 300-80=220 8.8 f.) Observation and Calculation: Notch impact strength = Absorb energy / Effective cross section area =220/25 =8.8 j/mm2 g.)Precautions:1. The specimen should be prepared in proper dimensions. 2. Take reading more frequently. 3. Make the loose pointer in contact with the fixed pointer after setting the pendulum. 4. Do not stand in front of swinging hammer or releasing hammer. 5. Place the specimen proper position.

17

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

h.)Result:The impact strength of given specimen = 8.8 j/mm2

VIVA QUESTIONS:1. What are the planes along which the greatest shear stresses occur? Greatest shear stress occurs at the planes which is inclined at 45 2. Define: Strain Energy When an elastic body is under the action of external forces the body deforms and work is done b y these forces. If a strained, perfectly elastic body is allowed to recover slowly to its unstrained state. It is capable of giving back all the work done by these external forces. This work done in straining such a body may be regarded as energy stored in a body and is called strain energy or resilience. 3. Define: Unit load method. load is removed and the unit load is applied at the point, where the deflection or rotation is to found 4. Give the procedure for unit load method. 1. Find the forces P1, P2, . in all the members due to external loads 2. Remove the external loads and apply the unit vertical point load at the joint if the vertical deflection is required and find the stress 3. Apply the equation for vertical and horizontal deflection.

18

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 5
Title of the Experiment: To study the UTM and perform the tensile test. Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To study the UTM and perform the tensile test. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. 1 2 3 4 UTM Mild steel specimen Vernier caliper/micrometer Dial gauge & graph paper Facilities required Quantity 1 1 1 1

b.)Theory:- Various m/c and structure components are subjected to tensile loading in numerous application. For safe design of these components, there ultimate tensile strength and ductility one to be determine before actual use. Tensile test can be conducted on UTM.A material when subjected to a tensile load resists the applied load by developing internal resisting force. These resistances come due to atomic bonding between atoms of the material. The resisting force for unit normal cross-section area is known as stress. The value of stress in material goes on increasing with an increase in applied tensile load, but it has a certain maximum (finite) limit too. The minimum stress, at which a material fails, is called ultimate tensile strength. The end of elastic limit is indicated by the yield point (load). This can be seen during experiment as explained later in procedure with increase in loading beyond elastic limit original cross-section area (Ao) goes on decreasing and finally reduces to its minimum value when the specimen breaks. c.) Specification of machine and specimen details:About UTM:The tensile test is conducted on UTM. It is hydraulically operates a pump, oil in oil sump, load dial indicator and central buttons. The left has upper, middle and lower cross heads i.e; specimen grips (or jaws). Idle cross head can be moved up and down for adjustment. The pipes connecting the lift and right parts are oil pipes through which the pumped oil under pressure flows on left parts to more the cross-heads. Specifications :1. Load capacity = 0-40000 kgf. 2. Least count = 8kgf. 3. Power supply = 440V

19

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

20

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

d.)Procedure for doing the experiment:Step No. 1. 2. 3. 4. 5. 6. 7. Details of the step The load pointer is set at zero by adjusting the initial setting knob. The dial gauge is fixed and the specimen for measuring elongation of small amounts. Measuring the diameter of the test piece by vernier caliper at least at three places and determine the mean value also mark the gauge length. Now the specimen is gripped between upper and middle cross head jaws of the m/c. Set the automatic graph recording system Start the m/c and take the reading.

The specimen is loaded gradually and the elongation is noted until the specimen breaks. e.)Tabulation:Percentage Percentage Specimen Length Diameter Area Intial Final Intial Final Intial Final
of of elongation reduction inlength(%) in area(%)

M.S. 302 345 12 9.03 113.04 64.01 12.46 f.) Observation and Calculation: (i) Initial diameter of specimen d1 = 12mm (ii) Initial gauge length of specimen L1 = 302mm (iii) Area of specimen a1 = 113.04 mm (iv) Final length after specimen breaking L2 = 345mm (v) Dia. of specimen at breaking place d2 = 9.03mm (vi) Cross section area at breaking place a2 = 64.01mm Percentage of elongation in length=CL/L= (345/302)/3345=0.1246 Percentage of reduction in area=CA/A=64.01/113.02=0.4337 g.)Precautions:1. The specimen should be prepared in proper dimensions. 2. The specimen should be properly to get between the jaws. 3. Take reading carefully. 4. After breaking specimen stop to m/c. h.)Result:Percentage of elongation in length=12.46% Percentage of reduction in area =43.87%

43.87

VIVA QUESTIONS:1.What is uniformly distributed load? If a load which is spread over a beam in such a manner that rate of loading w is uniform through out the length, then it is called as UDL. 2. Define shear force Shear force

21

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

SF at any cross section of is defined as the algebraic sum of all the forces acting either side of a beam. 3.Define Bending Moment at a section. BM at any cross section if the algebraic sum of the moments of all forces which are placed either side from the support. 4. What is meant by positive or sagging BM? BM is said to be positive or sagging if the moment of the forces in the left side of the beam is clockwise or right side of the beam is counter clock wise. Otherwise the beam to bend like concave manner. 5. What is meant by negative or hogging BM? BM is said to be positive or sagging if the moment of the forces in the left side of the beam is counter clockwise or right side of the beam is clock wise. Otherwise the beam to bend like concave manner.

22

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 6
Title of the Experiment: Double Shear Test On Given Specimen Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To conduct shear test on given specimen under double shear. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:- Equipments Required: S.No. 1 2 3 Facilities required UTM with double shear chuck Vernier Caliper Test Specimen Quantity 1 1 1

b.)Theory:- In actual practice when a beam is loaded the shear force at a section always comes to play along with bending moment. It has been observed that the effect of shearing stress as compared to bending stress is quite negligible. But sometimes, the shearing stress at a section assumes much importance in design calculations. Universal testing machine is used for performing shear, compression and tension. There are two types of UTM. (i)Screw type, (ii) Hydraulic type. Hydraulic machines are easier to operate. They have a testing unit and control unit connected to each other with hydraulic pipes. It has a reservoir of oil, which is pumped into a cylinder, which has a piston. By this arrangement, the piston is made to move up. Same oil is taken in a tube to measure the pressure. This causes movement of the pointer, which gives reading for the load applied. c.) Specification of machine:About UTM:The tensile test is conducted on UTM. It is hydraulically operates a pump, oil in oil sump, load dial indicator and central buttons. The left has upper, middle and lower cross heads i.e; specimen grips (or jaws). Idle cross head can be moved up and down for adjustment. The pipes connecting the lift and right parts are oil pipes through which the pumped oil under pressure flows on left parts to more the cross-heads. Specifications :1. Load capacity = 0-40000 kgf. 2. Least count = 8kgf. 3. Power supply = 440V d.)Procedure for doing the experiment:Step No. 1. 2. Details of the step Measure the diameter of the hole accurately. Insert the specimen in position and grip one end of the attachment in the upper portion and the other end in the lower portion.

23

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

3. 4. 5. 6. 7.

Switch on the main switch on the universal testing machine. Bring the drag indicator in contact with the main indicator. Gradually move the head control lever in left hand direction till the specimen shears. Note down the load at which specimen shears. Stop the machine and remove the specimen.

e.)Tabulation:Cross Non Shear Breaking sectional load in strength load area in mm N N/mm in N 1 M.S 5 19.6 15190 387 1000 f.) Observation and Calculation: Diameter of the specimen (d) = 5 mm Cross sectional area in double shear, (A) = 2 x d2 / 4 mm2 Shear Load taken by specimen at the time of failure (P) =15190 N. Shear strength = Maximum shear force =2P =2 x15190 Area of the specimen. = d2 = 52 =387.6 N/mm2 g.)Precautions:The inner diameter of the hole in the shear stress attachment is slightly greater than that of the specimen. h.)Result:The ultimate stress strength of the given specimen M.S. is 387.6 N/mm2 S.no Material Diameter in mm

VIVA QUESTIONS:1. What are the factors affect the strength column? 1.Slenderness ratio: Strength of the column depends upon the slenderness ratio, it is increased the compressive strength of the column decrease as the tendency to buckle is increased. 2. End conditions: Strength of the column depends upon the end conditions also 2 What is pure bending of a beam? When the loads pass through the bending axis of a beam, then there shall be pure bending of the beam. 3.What is shear centre or angle of twist? The shear centre for any transverse section of the beam is the point of intersection of the bending ax is and the plane of the transverse section

24

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 7
Title of the Experiment: Compression Test on Open Coil Helical Spring Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To determine the stiffness of spring, modulus of rigidity of the spring wire and maximum strain energy stored. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. Facilities required 1 2 3 Spring testing machine Open coil spring Vernier caliper Quantity 1 1 1

b.)Theory:- This is the test to know strength of a material under compression. Generally compression test is carried out to know either simple compression characteristics of material or column action of structural members. It has been observed that for varying height of member, keeping cross-sectional and the load applied constant, there is an increased tendency towards bending of a member. Member under compression usually bends along minor axis, i.e, along least lateral dimension. According to column theory slenderness ratio has more functional value. If this ratio goes on increasing, axial compressive stress goes on decreasing and member buckles more and more. End conditions at the time of test have a pronounced effect on compressive strength of materials. Effective length must be taken according to end conditions assumed, at the time of the test. As the ends of the member is made plain and fit between two jaws of the machine, fixed end is assumed for calculation of effective length. Effective length is taken as 0.5 L where L is actual length of a specimen. c.)Procedure for doing the experiment:Step No. 1. 2. 3. Details of the step By using vernier caliper measure the diameter of the wire of the spring and also the diameter of spring coil. Count the number of turns Insert the spring in the spring testing machine and load the spring by a suitable weight and note the corresponding axial deflection in compression. Increase the load and take the corresponding axial deflection readings. Plot a curve between load and deflection. The shape for the curve gives the stiffness of the spring. .

4. 5. 6.

25

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

d.)Tabulation:Sl.No Load in N Scale readings in mm Deflection in mm Rigidity modulus in N/mm2 0 0.52105 2.41105 1.91105 3.1105 Stiffness in N/mm 0 15 24 17.5 15.66

1. 0 415 415 0 2. 15 423 424 1 3. 24 426 427 1 4. 35 431 433 2 5. 47 435 438 3 e.) Observation and Calculation: (i) Inner diameter of spring di = 3.1mm (ii) Outer diameter of spring do=3.9mm (iii) Length of th spring l =69 mm (iv) Number of turns n= 10 (v) Material of spring=steel (vi) Youngs modulus =2105 1. Deflection () = 64 WR3N Sec [ cos2 / N + 2Sin2 /E] d2 =424-423=1 mm Where, W=Load applied in Newton R=Mean radius of spring coil = (D-d) / 2 N= Number of turns =Helix angle of spring N=Modulus of rigidity of spring Material E=Youngs modulus of the spring material 2. Tan = pitch / 2R =tan-1(6.3/2 x13.25) =3.18 3. Pitch = (L-d) / n =(69-3)/10 =6.3 Where, d=Dia of spring wire in mm L=Length of spring in mm N=no of turns in spring 4. Stiffness of spring (K)=w / =15/1 =15 Where, =Deflection of spring in mm W=Load applied in Newtons

N/mm2

26

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

5. Maximum energy stored = 0.5 x Wmax x max =0.5 x47 x3 =70.5 Where, Wmax=Maximum load applied Max=Maximum deflection f.)Precautions:1. Place the specimen at center of compression pads, 2. Stop the machine as soon as the specimen fails. 3. Cross sectional area of specimen for compression test should be kept large as compared to the specimen for tension test: to obtain the proper degree of stability g.)Result:Under compression test on open coil helical spring 1. Rigidity Modulus (N) =3.1105 N/mm2 2.Stiffness of spring (K)= 15.66 N/mm 3. Maximum energy stored =70.5

VIVA QUESTIONS:1. Define principal stresses and principal plane? Principal Stresses: The magnitude of normal stress, acting on a principal plane is known as principal stresses. Principal Plane: The planes which have no shear stress are known as principal planes. 2. What is the radius of Mohrs circle? Radius of Mohrs circle is equal to the maximum shear stress. 3. What is the use of Mohrs circle?

27

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 8
Title of the Experiment: Torsion Test on Mild Steel Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To find the modulus of rigidity. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. Facilities required Quantity 1 2 3 4
A torsion testing apparatus. Standard specimen of mild steel . Twist meter for measuring angles of twist. A steel rule and calipers and 1 micrometer. b.)Theory:- A torsion test is quite instrumental in determining the value of rigidity (ratio of shear stress to shear strain) of a metallic specimen. The value of modulus of rigidity can be found out through observations made during the experiment by using the torsion equation. T/ Ip =C /L or C=TL/I Where T=torque applied, Ip= polar moment of inertia, C=modulus of rigidity, = Angle of twist (radians), and l= gauge length. In the torque equipment refer fig. One end of the specimen is held by a fixed support and the other end to a pulley. The pulley provides the necessary torque to twist the rod by addition of weights (w). The twist meter attached to the rod gives the angle of twist. c.)Procedure for doing the experiment:Step No. Details of the step

1 1 1

1. 2. 3. 4.

Prepare the testing machine by fixing the two twist meters at some constant lengths from fixed support. Measure the diameter of the pulley and the diameter of the rod Add weights in the hanger stepwise to get a notable angle of twist for T1 and T2 Using the formula calculate C

28

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

d.)Tabulation:S.NO ANGLE ANGLE TORQUE MODULUS OF OF OF TWIST TWIST RIGIDITY UNIT Degree Radian Kgf/cm Nm N/m2 1. 40 69.8 87.5 8.75 1.651010 2. 90 1.57 100.25 10.025 5.5104 3. 110 1.92 160.25 16.025 1.11010 e.) Observation and Calculation: T/ Ip =C /L J=/32d4=/3264=0.16 Ip= polar moment of inertia, =698 L= gauge length C= T / Ip L =1.651010 f.)Precautions:1. The specimen should be prepared in proper dimensions. 2. The specimen should be properly to get between the jaws. 3. Take reading carefully. 4. After breaking specimen stop to m/c. g.)Result:Modulus of rigidity of the shaft is 1.651010 N/m2

SHEAR STRESS N/m2 2.05108 2.37108 3.39108

29

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

VIVA QUESTIONS:1.Define: Column and strut. A column is a long vertical slender bar or vertical member, subjected to an axial compressive load and fixed rigidly at both ends. A strut is a slender bar or a member in an y position other than vertical, subjected to a compressive load and fixed rigidly or hinged or pin jointed at one or both the ends. 2. What are the types of column failure? a. Crushing failure: The column will reach a stage, when it will be subjected to the ultimate crushing stress, beyond this the column will fail by crushing The load corresponding to the crushing stress is called crushing load. This type of failure occurs in short column. b. Buckling failure: This kind of failure is due to lateral deflection of the column. The load at which the column just buckles is called buckling load or crippling load or critical load. This type of failure occurs in long column 3. What is slenderness ratio (buckling factor)? What is its relevance in column? It is th e ratio of effective length of column to the least radius of gyration of the cross sectional ends of the column. Slenderness ratio = l eff / r l eff = effective length of column r = least radius of gyration Slenderness ratio is used to differentiate the type of column.Strength of the column depends upon the slenderness ratio,it is increased the compressive strength the column decrease as the tendency to buckle is increased.

30

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 9
Title of the Experiment: Deflection Test on Beam Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To find the youngs modulus of the given specimen by doing deflection test. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. 1 2 3 4 Facilities required Bending table. Deflecto meter Weight Scale and specimen Quantity 1 1 1 1

b.)Theory:- Bending test is perform on beam by using the three point loading system. The bending fixture is supported on the platform of hydraulic cylinder. The loading is held in the middle cross head. At a particular load the deflection at the center of the beam is determined by using a dial gauge. c.)Procedure for doing the experiment:Step No. 1. 2. 3. 4. 5. Details of the step Note down the length and cross section of the given specimen. Set the span length as beam of adjusting the movable supports. Now place the given beam over the knife edges. Place the load hanger on the beam at i at a distance of (1/3xSpan) from the left support. Fit the deflecto meter at I at a distance of (2/3xSpan) from the left support. Adjust the deflecto meter to read zero Add the set of weights one by one and record the corresponding deflecto meter reading it. Draw a graph between loads vs. deflection for both the positions. ix) Youngs modulus can be found by the following

6. 7.

31

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

d.)Tabulation:S.No Load Kg 1. 2. 3. 4. 5. 0 50 100 150 200 N 0 490.5 981 1471.5 1962

Deflection reading in division Loading 0 75 152 228 301 Unloading 2 78 153 228 301 Division 1 76.5 152.5 228 301 Div x lc 0.01 0.765 1.525 2.28 3.01

Youngs modulus N/mm2 0 18585105 1.8646105 1.8707105 1.8894105

e.) Observation and Calculation: (i Youngs modulus E = Wab(L2-a2-b2) ___________ 6ILy

32

Dr.NNCE

MECH/IV SEM 490.5 x600 x300[9002-6002-3002] ____________________________

SOM LAB -LM

6 x414 x900 x76.5 =1.8585 x105 N/mm2 Where=Load in N a= Deflecto meter distance from left support in mm b=Load distance from left support in mm I=bd3/12 mass moment of inertia L=Span of the beam in mm y =Deflection meter reading in mm f.Precautions:- . 1. Test piece should be properly touch the fixture. 2. Test piece should be straight. 3. Take reading carefully. 4. Elastic limit of the beam should not be exceeded. g.Result:Youngs modulus analytically =1.8585 x105 N/mm2

VIVA QUESTIONS:1.Define beam? Beam is a structural member which is supported along the length subjected to external loads acting transversely. ie., perpendicular to the centre of the beam. Beam is sufficiently long as compared to external load. 2.What is meant by transverse loading on beams? If a load is acting on the beam which perpendicular to the support centre line Then it is called transverse loading. 3.How do you classify the beams according to its supports? The beam may be classified according to the support Cantilever Simply supported beam Over hanging beam Fixed beam Continuous beam 4. What is cantilever beam? A beam with one end free and other end fixed is called Cantilever beam 5. What is simply supported beam? A beam supported or resting freely on the supports at its both ends the its is called simply supported beam. 6. What is over hanging beam? If beam one or both end extend beyond the support limit then it is called as over hanging beam.

33

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 10
Title of the Experiment: Microscopic Examination Date of the Experiment: STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To examine the microstructure of a given plain carbon steel sample before and after heat treatment. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. 1 2 3 4 5 Facilities required Belt grinder Simple disc polishing machine Stretching agent Emery sheet Muffle furnace Quantity 1 1 1 1 1

b.)Theory:Sample specimen: i) Unbalanced specimen ii) Harden specimen iii) Tempered specimen Steel can be heat treated to high temperature to achieve the requirement harden and strength. The high operating stress need the high strength of hardened structure similarly tools such as like knives etc. as quenched hardened steels are so, brittle than even slight compact cause fracture. The heat treatment that reduces the brittleness of steel without significantly lowering the hardness and strength. Hardened steel must be tempered before use. Significance: Hardening: To increase the strength and hardness To improve the mechanical properties Hardening temperature-9000c Holding time-1 hr Quenching medium - Water. Tempering: To reduce the stress To reduce the brittleness Tempering temperature-320 C Holding time-1 hr Quenching medium-Air The specimen and is heated at a temperature which is determined using the microstructure the specimen quenching into oil. The given three samples are subjected to

34

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

the study of microstructure of the hardened metal. The micro structure of the unhardened sample is studied and hardness is found. The furnace which is maintained at temperature at 900 C for hardening. The sample is added to get austenite structure. The third sample is subjected to tempering process of is hold at 830 is furnace for this and quenched in air. The micro structure of the third specimen is studied and hardness is formed. c.)Procedure for doing the experiment:Step No. 1. Details of the step

Specimen is heated to temperature which is determined using the microscopic structure the specimen is quenched in oil. The given samples are subjected to the study of micro structure and 2. hardness. The microstructure of the hardened sample is subjected and hardness 3. is found. The remaining two specimens is quenched into the furnace which is 4. maintained at the temperature 9000c for hardening process. The specimen is then taken from the furnace and immediately 5. quenched in oil. d.)Tabulation:SAMPLES SAMPLES-I SAMPLES-I SAMPLES-II (Before hardening) (After hardening) (After tempering) MICROSTRUCTURE Structure1 Structure 2 Structure 3 HARDENING RC81 RC98 RC95

e.) Observation Specimen: Low Carbon Steel Magnification: 2% Metal Composition: 80%Ferrite, 20% Pearlite Hardness test: RC Load: 100 kg Indentor:1 200C f.)Precautions:- . 1. Test piece should be clean properly. 2. Test piece should be straight. g.)Result:Thus the microstructure and the hardness of the given sample are studied and treatment is tabulated.

VIVA QUESTIONS:1.) Define hardening. It is a heat treatment process to increase the strength and hardness. 2. Name some quenching mediums. Air, water, oil.

35

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

Experiment Number: 11
Title of the Experiment: - Brinell Hardness Test (In Tempered Material) Date of the Experiment:STEP 1: OBJECTIVE (AIM) OF THE EXPERIMENT To find the brinell hardness number of tempered metals and hardened material. STEP 2: FACILITIES REQUIRED AND PROCEDURE a.)Facilities required to do the experiment:S.No. 1. Facilities required Brinell Hardness Quantity 1

testing machine 2. 3. 4. Specimen of Tempered metal Specimen of Hardened metal Brinell microscope 1 1 1

b.)Theory: - Hardness represents the resistance of material surface to abrasion, scratching and cutting, hardness after gives clear identification of strength. In all hardness testes, a define force is mechanically applied on the test piece for about 15 seconds. The indentor, which transmits the load to the test piece, varies in size and shape for different tests. Common indenters are made of hardened steel or diamond. In Brinell hardness testing, steel balls are used as indentor. Diameter of the indentor and the applied force depend upon the thickness of the test specimen, because for accurate results, depth of indentation should be less than 1/8 of the thickness of the test pieces. According to the thickness of the test piece increase, the diameter of the indentor and force are changed. Knowledge of the specimen: Load is applied on the specimen the band of the slide of the machines which is operated of handling and watching the specimen the diameter of the indentor is which helps of traveling microscope. c.)Specification of Hardness Testing machine and Indentors:A hardness test can be conducted on Brinell testing m/c, Rockwell hardness m/c or vicker testing m/c. the specimen may be a cylinder, cube, think or thin metallic sheet.Its specification are as follows: 1. Ability to determine hardness upto 500BHN. 2. Diameter of ball (as indentor) used D = 2.5mm, 5mm, 10mm. 3. Maximum application load = 3000kgf. 4. Method of load application = Lever type 5. Capability of testing the lower hardness range = 1 BHN on application of 0.5Dload

36

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

d.)Procedure for doing the experiment:Step No. 1. 2. 3. 4. 5. 6. 7. 8. Details of the step Insert ball of dia D in ball holder of the m/c. Make the specimen surface clean by removing dust, dirt, oil and grease etc. Make contact between the specimen surface and the ball by rotating the jack adjusting wheel. Push the required button for loading. Pull the load release level and wait for minimum 15 second. The load will automatically apply gradually Remove the specimen from support table and locate the indentation so made. View the indentation through microscope and measure the diameter d by micrometer fitted on microscope. Repeat the entire operation, 3-times.

e..)Tabulation:S.No. Ball Load applied P Diameter of P/D2 BHN Diameter in indentation in mm kgf. d (mm) 1.(Tempered 10 3000 3.8 30 670.345 Specimen.) 2.(Hardened 10 3000 4.3 30 697.34 Specimen.) f.) Observation and Calculation: Area of indentation A=d/2(D-D2-d2) =3.8/2(10-102-3.82) =4.4753 BHN = Load Applied (kgf.)/ Spherical surface area indentation (in mm.) =3000/4.4753 =670.345 g.)Precautions:1. The specimen should be clean properly. 2. Take reading more carefully and correct. 3. Place the specimen properly. 4. Jack adjusting wheel move slowly 5. After applying load remove the load. h.)Result:The brinell hardness number of the given specimen are found out and tabulated.

37

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

VIVA QUESTIONS:1.)Define tempering. It is a heat treatment process to reduce the stress and brittleness.

2. Define safe load. It is the load to which a column is actually subjected to and is well below the buckling load. It is obtained b y dividing the buckling load by a suitable factor o f safety (F.O.S). Safe load = Buckling load /Factor of safety 3. State Hookes law. It states that when the material is loaded, within its elastic limit, the stress is directly proportional to the strain. Stress Strain 4. Define Factor of Safety. It is defined as the ratio of ultimate tensile stress to the permissible stress(working stress).

38

Dr.NNCE

MECH/IV SEM

SOM LAB -LM

MODEL QUESTIONS 1. To study the brinell hardness testing machine & perform the brinell hardness test. 2. To study the Rockwell Hardness testing machine and perform the Rockwell hardness test. 3. To study the Impact Testing m/c and Perform Izod impact test. 4. To study the Impact Testing m/c and Perform charpy impact test. 5. To study the UTM and perform the tensile test. 6. To conduct Double Shear Test On Given Specimen 7. To conduct Compression Test on Open Coil Helical Spring 8. To conduct Torsion Test on Mild Steel 9. To conduct Deflection Test on Beam

39