Scribd
Upload
187 views4 pages

At New at End

Control break statements in ABAP allow code to be executed when certain conditions are met within a loop. There are 5 control break statements: AT FIRST, AT LAST, AT END OF, AT NEW, and ON CHANGE OF. AT FIRST executes code at the beginning of the loop. AT LAST executes code at the end of the loop. AT END OF, AT NEW, and ON CHANGE OF execute code when the value of a specified field changes within the sorted table that is being looped over. An example program demonstrates the usage of each control break statement.

Uploaded by

ClasesXXX
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
187 views4 pages

At New at End

Control break statements in ABAP allow code to be executed when certain conditions are met within a loop. There are 5 control break statements: AT FIRST, AT LAST, AT END OF, AT NEW, and ON CHANGE OF. AT FIRST executes code at the beginning of the loop. AT LAST executes code at the end of the loop. AT END OF, AT NEW, and ON CHANGE OF execute code when the value of a specified field changes within the sorted table that is being looped over. An example program demonstrates the usage of each control break statement.

Uploaded by

ClasesXXX
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Control Break Statements in SAP ABAP

Control break statements are like events inside the loop. There are 5 control break statements in ABAP. These are used within loop.(Except ON CHANGE OF which can be used outside the loop as well)

AT FIRST - ENDAT AT NEW - ENDAT AT END OF - ENDAT AT LAST - ENDAT ON CHANGE OF

Explanation:
AT FIRST : Will trigger at the first run of the loop. AT LAST: Will trigger at the last run of the loop. The below 3 events are normally used when the table is sorted.

AT END OF : When we use At end for a field, it will trigger whenever there is any change in any of the fields from the left to that of the particular field. The trigger point will be the at the last occurrence of the same value for the field. AT NEW: When we use At new for a field, it will trigger whenever there is any change in any of the fields from the left to that of the particular field.The trigger point will be the at the first occurrence of the new value for the field. ON CHANGE OF: On change of it triggers only when there is any change in the particular field. On change of can be used outside the loop too

Example Program:
Here is an example program which gives you the practical understanding of all control break statements.

Example Program for Control Break Statements

NOTE: It is important to note that we need a temporary work-area apart from the workarea used in loop for the last 3 control break statements. If we directly use the work-area of the loop, then we will get **** value and not the output we are expecting.

*&---------------------------------------------------------------------* *& Report *& *&---------------------------------------------------------------------* *& NEW TO SAP CONTROL BREAK EXAMPLE *& http://www.newtosap.info *& *&---------------------------------------------------------------------* ZAU_CONTROLBREAK

REPORT

zau_controlbreak.

TYPES: BEGIN OF ty_marc, matnr TYPE marc-matnr, werks TYPE marc-werks,

END OF ty_marc.

DATA: it_marc TYPE STANDARD TABLE OF ty_marc, wa_marc TYPE ty_marc, wa_temp TYPE ty_marc.

SELECT matnr werks FROM marc INTO TABLE it_marc UP TO 10 ROWS WHERE matnr ge 40. SORT it_marc BY matnr. FIELD-SYMBOLS : <matnr> type matnr.

WRITE:/ 'FULL TABLE'. LOOP AT it_marc INTO wa_marc. wa_temp = wa_marc. WRITE: / sy-tabix , wa_temp-matnr, ENDLOOP. wa_temp-werks.

WRITE:/ 'AT FIRST AND LAST'. LOOP AT it_marc INTO wa_marc. wa_temp = wa_marc. AT FIRST. WRITE:/ 'First Entry'. WRITE:/ ENDAT. AT LAST. WRITE:/ 'Last Entry'. WRITE:/ ENDAT. ENDLOOP. wa_temp-matnr, wa_temp-werks. wa_temp-matnr, wa_temp-werks.

WRITE:/ 'AT END OF'. LOOP AT it_marc INTO wa_marc. wa_temp = wa_marc. AT END OF matnr. WRITE: / sy-tabix , wa_temp-matnr, ENDAT. wa_temp-werks.

ENDLOOP.

WRITE:/ 'AT NEW'.

LOOP AT it_marc INTO wa_marc. wa_temp = wa_marc. AT NEW matnr. WRITE: / sy-tabix , wa_temp-matnr, ENDAT. ENDLOOP. wa_temp-werks.

WRITE:/ 'ON CHANGE OF'. LOOP AT it_marc INTO wa_marc. wa_temp = wa_marc. ASSIGN wa_marc-matnr TO <matnr>. ON CHANGE OF wa_marc-matnr. WRITE: / sy-tabix ,wa_temp-matnr, ENDON. ENDLOOP. wa_temp-werks.

You might also like