Special Edition/Signature B60 Keurig Brewer

OWNER S MANUAL

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should be followed, including the following:
1. Read all instructions before using. 2. Do not touch hot surfaces. Use handles
3. This appliance must be properly

Safe Operation & Use

electrical short circuit, grounding reduces the risk of electrical shock. 19. If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. 20. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter. 21. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. 22. Do not use the appliance for other than its intended use.

11. For best operation, plug the appliance

and knobs when available.

installed and located in accordance with these instructions before it is used. 4. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electrical shock or injury to persons. 5. Do not place on or near a hot gas or electric burner, or in a heated oven. 6. Do not use outdoors. 7. To protect against fire, electric shock and injury do not immerse cords, plugs, or the appliance in water or any other liquid. 8. Do not overfill the Water Reservoir with water. 9. Use only water in this appliance! Do not put any other liquids or foods in the Water Reservoir except as instructed in the Cleaning Instructions in this guide. 10. Turn off and unplug the Brewer before cleaning or maintenance. Allow to cool before putting on or taking off parts and before cleaning the appliance.

into its own electrical outlet on a dedicated circuit to prevent flickering of lights, blowing of fuses or tripping a circuit breaker. 12. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is damaged in any manner. Contact Keurig Customer Service to report any malfunction of or damage to the Brewer. 13. Do not let the cord hang over the edge of the table or counter, or touch hot surfaces. 14. To disconnect, press the Power Button on the Brewer to OFF status and then remove the plug from the wall outlet. 15. Close supervision is necessary when any appliance is used by or near children. 16. Do not lift the Brewer Handle while brewing is in progress. 17. Always keep the Water Reservoir Lid on the Water Reservoir unless you are refilling it. 18. This appliance is equipped with a power cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an
2

CAUTION: There are two sharp needles that puncture the K-Cup pack, one above the K-Cup Pack Holder and the other in the bottom of the K-Cup Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup Pack Assembly Housing. CAUTION: There is extremely hot water in the K-Cup Pack Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Pack Assembly Housing during the brewing process. CAUTION: Please always keep the Brewer in its upright position to avoid potential injury and/or damage to your Brewer. SHORT CORD INSTRUCTIONS: A short power supply cord is provided to

TABLE OF CONTENTS
KEURIG GOURMET SINGLE CUP HOME BREWING SYSTEM Special Edition/Signature B60 Using Your Brewer

SET-UP Helpful Hints......................................................................................... 4 Unpacking............................................................................................. 4 Features................................................................................................ 5 SECTION 1SET-UP & FIRST BREW Set-Up & First Brew............................................................................ 6 SECTION 2CONTROLS & INDICATORS Setting the Clock................................................................................ 10 Programming On/Off Features....................................................... 10 Programming Brew Temperature.................................................. 12 SECTION 3CLEANING & MAINTENANCE Cleaning............................................................................................... 12 De-Scaling.......................................................................................... 13 Storage................................................................................................ 14 SECTION 4TROUBLESHOOTING................................................... 15 SECTION 5WARRANTY................................................................. 16 Record your Brewer Serial Number here.
See Unpacking Instructions on page 4 for serial number location.

reduce the risk of becoming entangled in or tripping over a longer cord. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance; (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally; and (3) the extension cord must include a 3-prong grounding plug. THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

SAVe These Instructions.

WARNING TO USERS AND PARENTS 1. DO NOT permit children to use Brewer unless there is adult supervision. Brewer dispenses very hot water. 2. SPECIAL NOTICE FOR HOT COCOA USERS: IMMEDIATELY AFTER USING A HOT COCOA K-CUP PACK, RUN a Hot Water Brew Cycle without a K-Cup pack to avoid the possibility of clogging the exit needle. DO NOT assume the next user will do this.

THIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING

WARNING !
RISK OF FIRE OR ELECTRIC SHOCK DO NOT OPEN

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.
3

Removing the serial number label from the Brewer will void warranty.

Set-Up
Helpful Hints
1. Plug Brewer into its own grounded outlet. 4. Customize the size, flavor & brew thats perfect for you. 2. Remove enclosed literature. 3. Turn the box on its side with front of box

Features
With the choice of over 200 varieties of K-Cup packs and 3 brew sizes (Small Cup5.25 oz., Small Mug-7.25 oz. and Large Mug-9.25 oz.), your Keurig Brewer gives you endless options to customize the size, flavor and brew thats perfect for you. For a strong, intense cup, select an Extra Bold K-Cup pack (with up to 30% more ground coffee than regular varieties) and brew size thats right for you. The smaller the brew size, the more intense flavor in your cup. The larger the brew size, the less intense flavor in your cup. Please see page 7 for brewing instructions. face down.

Special Edition/Signature Model B60 Brewer

D G T

If the electric circuit is overloaded with other appliances, your Brewer may not function properly. The Brewer should be operated on its own circuit, separate from other appliances.

A
READY TO BREW
11: 56 AM
MENU

4. Reach into the box and grasp the plastic bag

that contains the Brewer.

5. Carefully pull the plastic bag (and packaging

M H B N C E F

2. Keep your Brewer turned ON.

To brew a fresh cup of coffee, tea or hot cocoa anytime you want, keep your Brewer turned ON all the time. However, the Brewer is fully programmable so you can set it to turn on and off automatically to match your schedule. Or, if you prefer, set the Brewer to automatically turn off after a period of time. Follow the simple instructions on pages 1012 to find the settings that are most convenient for you.

materials) toward you and out of the box. The Brewer will still be encased in the polyfoam and be on its side.

6. Remove the top polyfoam packaging material. 7. Carefully lift Brewer off of the bottom polyfoam

and place it upright on a flat, steady surface.

5. Remove K-Cup pack after use. 6. Brewing into a travel mug.

8. Lift plastic bag off of Brewer. 9. Record the serial number for this Brewer on

J 0 P Q

3. For the best tasting gourmet coffee, tea or hot cocoa, Keurig recommends using bottled or filtered water.

To brew into a travel mug, simply remove the Drip Tray Assembly and place the travel mug on the Drip Tray Base. Please see pages 13 and 14 for instructions.

page 3 of this guide. The serial number can be found on the bottom of the Brewer box or on the Brewer behind the Drip Tray (when removed).

Water quality varies from place to place. If you notice an undesirable taste in your cup of coffee, such as chlorine or other mineral tastes, we recommend you consider using bottled water or water from a filtration system. For best results, carefully follow manufacturers instructions when using any water filtration system.

7. De-scale Brewer regularly.

10. Place the Brewer upright on a flat, steady

Unpacking Instructions
1. Place Brewer box on a large steady surface

surface. Remove tape holding Water Reservoir in place.

Special Edition/Signature B60 Brewer

A. Water Reservoir Lid B. Water Reservoir C. Water Reservoir D. Handle E. Funnel F. K-Cup Pack Holder

Controls and Indicators

J. Drip Tray Plate K. Drip Tray L. Drip Tray Base M. Vent N. Power Cord O. Small Cup Button 5.25 oz. P. Small Mug Button 7.25 oz. Q. Large Mug Button 9.25 oz. R. Menu Button S. LCD Control Center T. Power Button

We recommend you save all packing materials in case future shipping of the product is necessary.

Lock Tab Slots

(such as a table or countertop) or on the floor. Open the box. 4

Keep all plastic bags away from children.

WARNING:

(E and F are the K-Cup Pack Holder Assembly) G. Lid H. K-Cup Pack Assembly Housing I. Housing

SECTION 1

Set-Up & First Brew

Lock Tabs
g.

it has been set-up for its rst use as set forth below. NOTE: If Brewer has been exposed to temperatures below freezing, allow Brewer at least two hours to reach room temperature before brewing. A frozen or extremely cold Brewer will not operate.
g.

IMPORTANT: You cannot use your Keurig Brewer until

2
4. Fill Water Reservoir with bottled or filtered

g.

8. The Brewer will automatically fill the

water so that the water level is just below the top edge of the Water Reservoir.
5. Place Water Reservoir base into the left side

NOT READY

internal tank with water and then the water will be heated. This will take about 4 minutes. During the heating period, NOT READY (fig. 4) is indicated on the LCD Control Center. Do not lift Handle during this
heating period.

g.

Ready to Brew Your First Cup

1. LCD Control Center will indicate READY TO BREW.
2. Place a cup or mug on the Drip Tray Plate. 3. Lift the Handle and the K-Cup Pack Holder

of the Brewer and be sure the Water Reservoir Lock Tabs engage with the Brewer. Replace Lid on Water Reservoir.
6. Press the Power Button found directly

Once the water is heated, READY TO BREW will be indicated and the Brew Buttons will be illuminated (fig. 5). NOTE: You may see small
amounts of water coming from the Vent and dripping into the Water Reservoir during this and subsequent heatingthis is normal.
g.

will open toward you (fig. 6).

4. Select a K-Cup pack. NOTE: Do not remove the foil lid or puncture the K-Cup pack. 5. Place a K-Cup pack in the

Setting Up Your Brewer

1. Unwrap cord and plug the Brewer into

above the LCD Control Center (fig. 3).

7. The LCD Control Center will illuminate and indicate NOT READY. NOTE: A K-Cup pack should not be used for this sequence.

K-Cup Pack Holder (fig. 7).

CAUTION: There are two sharp needles that puncture the K-Cup pack, one above the K-Cup Pack Holder and the other in the bottom of the K-Cup Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup Pack Assembly Housing. 6. Lower the Handle to close the Lid over the

a grounded outlet. Remove all pieces of packing tape and clear plastic sticker from LCD Control Center.
2. Place a large mug (10 oz. minimum) on the

g.

Power
NOT READY ADD WATER

NOTE: If the Water Reservoir is empty or

not in place on the Brewer, the LCD Control Center will also indicate ADD WATER. None of the buttons will be activated until water is added to the Water Reservoir and Water Reservoir is in place.
READY TO BREW
MENU

9. Lift and lower the Handle. Press the Small

Mug Button to start a cleansing brew. Pour the hot water into the sink.
10. The one-time set-up process is now

g.

Drip Tray Plate.

3. Remove the Water Reservoir from Brewer

complete and you are ready to brew!

NOTE: The Brewer may take 15 seconds between brews and then READY TO BREW will be indicated.

by first removing Lid from Reservoir (fig. 1), then lifting Reservoir straight up and away from Brewer (may be tight), (fig. 2). Rinse with fresh water.

Small Mug

K-Cup Pack Holder. (When it is closed completely, the LCD Control Center will indicate READY TO BREW and the Small Cup, Small Mug and Large Mug Buttons will flash for up to 60 seconds.)

SECTION 1 Set-Up & First Brew

Ready to Brew Your First Cup (Continued) 7. Choose the cup size of coffee, tea or hot 10. Lift the Handle, remove and dispose of the used K-Cup pack. CAUTION: K-Cup pack will be hot. 11. Enjoy your first cup of Keurig Brewed

Adding Water
fig.

Brewing Hot Water

The LCD Control Center will indicate ADD WATER when the water level in the Water Reservoir is low or if the Water Reservoir has been removed (fig. 8). The blue light in the Water Reservoir will also blink when water needs to be added. The Brewer will not allow you to brew when ADD WATER is indicated.
The Water Reservoir can be filled in two ways. 1. Lift off the Water Reservoir Lid and pour water

Small Cup
(5.25 oz.)

cocoa by pressing the button that indicates your choice. The Small Cup choice will yield a 5.25 oz. serving, the Small Mug choice will yield a 7.25 oz. serving and the Large Mug choice will yield a 9.25 oz. serving. NOTE: If
you do not push a Brew Button in 60 seconds, the LCD Control Center will return to READY TO BREW and the Brew Buttons will be disabled to prevent accidental activation. Re-activate the Brew Buttons by raising and lowering the Handle completely. 8. The LCD Control Center will indicate

gourmet coffee, tea or hot cocoa!

12. Your Brewer may indicate NOT READY as it

Your Brewer is able to produce hot water for making hot cocoa from a packet, for use in cooking, for making soups, etc. Simply follow the instructions on page 7 Ready To Brew Your First Cup without adding a K-Cup pack.
NOTE: After brewing a hot cocoa K-Cup pack, we recommend running a cleansing brew without a K-Cup pack.

heats water for the next brew cycle. The READY TO BREW indication will return to the LCD Control Center in about 15 seconds.
NOTE: Following the brew, your Brewer will fill in preparation for the next brew. The pump will make a vibrating sound. This is normal.

NOT READY ADD WATER

Purging the Brewer

If your Brewer has not been used for more than one week, you should purge the water from the inner tank.
1. If there is water in the Water Reservoir, remove the Lid, then lift the

Small Mug
(7.25 oz.)

directly into the Water Reservoir while it is still attached to the Brewer, then replace the Lid.
2. Remove the Water Reservoir from Brewer by first removing Lid from

Large Mug
(9.25 oz.)

BREWING and the cup size you selected will illuminate. CAUTION: There is extremely
hot water in the K-Cup Pack Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup Pack Assembly Housing during the brew process. 9. There may be a short pause prior to coffee

Stopping the Brew Process

If you need to stop brewing after the process has started, press the Power Button to turn the Brewer off. The flow of coffee, tea or hot cocoa will stop, the heating element will shut off, and the blue lights illuminating the brew buttons and Water Reservoir will disappear. NOTE: You may get less coffee, tea
or hot cocoa in your cup during your next brew. We recommend that you perform a cleansing brew after a terminated brew. Then your NEXT brew will be the volume you have selected.

the Water Reservoir, then lifting the Water Reservoir straight up and away from Brewer. Fill with water. Place the Water Reservoir back on the Brewer and replace the Lid. IMPORTANT: Do not remove the
Water Reservoir during the brewing process.

Water Reservoir straight up and away from Brewer. Discard water, rinse and refill with water. Place the Water Reservoir back on the Brewer and replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2. Be sure the Brewer is turned on. Raise and lower the Handle on the

Brewer without inserting a K-Cup pack.

3. The LCD Control Center will indicate READY TO BREW and the Small

Brewing Iced Beverages

Your iced tea and iced coffee taste best when fresh-brewed hot over ice. Try it by placing a tall cup filled with ice on the Drip Tray Plate (the Drip Tray Assembly can be removed to accommodate taller cups), choose your favorite K-Cup pack and press your preferred cup size. Also, look for the Brew Over Ice icon on K-Cup packs that are specially crafted to brew over ice! IMPORTANT: Do not
brew into a cup made of glass. Doing so may cause the glass to crack or break.

Cup, Small Mug and Large Mug Buttons will flash. Be sure to have a large mug on the Drip Tray Plate and then press the Large Mug Button.
4. Repeat steps 2 and 3 one more time to completely purge water from

being dispensed. The entire brew process lasts for approximately 1 minute and ends with a burst of air to remove all liquid from the K-Cup pack.

inner tank.
If you are experiencing any problems with your Brewer, please contact Customer Service at 1.866.901.BREW (2739).

SECTION 2
Setting the Clock

Controls & Indicators (LCD Control Center)

Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea or hot cocoa on your own schedule. By programming your Brewer to turn on each morning, you will never have to wait for the Brewer to warm up to brew a gourmet cup of coffee.
1. Leave it ON all the time. The Brewer can be left on all the time so that it is

fig.

11

Setting the clock is optional. When the clock is set, the time will appear in the LCD Control Center. NOTE: You must set the clock if you will be using the
On/Off Time programming feature.
fig.

READY TO BREW
AUTO OFF SET

c. After setting the desired Auto Off time, press the Menu Button four times to scroll through the remaining programming options and exit the programming mode. AUTO OFF SET (fig. 11) will now be indicated to confirm that it has been set. d. To cancel the Auto Off feature, press the Menu Button twice to reach the Auto Off programming mode. Press and release the Small Cup Button under the blinking H to advance one hour at a time until OFF is indicated.

fig.

13

e. If you want to set an OFF TIME, repeat the procedure above in steps b & c to set your desired OFF TIME. f. To complete the process, press the Menu Button two more times to exit the programming mode. The LCD Control Center will indicate the options you have set. g. The On Time and Off Time functions operate independently from one another. To cancel either set function, follow the steps above and use the H and M buttons to advance to 12:00 AM. Make sure the M button is set to :00, then change the H button. When you reach 12:00 AM, the Control Center will indicate OFF and the function will be disabled.
EXAMPLE: If you chose to set the On Time at 6:15 AM and the Off Time for 10:00 PM, then the Brewer will be READY TO BREW and maintain hot water in the tank during that time so that it is always ready for you to brew. If you wanted to brew outside this window, simply press the Power Button and you can brew as soon as the water is heated and the READY TO BREW is indicated on the LCD Control Center.

SET

CLOCK AUTO OFF OFF TIME BREW TEMP

AM PM

11: 56 AM
MENU

MENU

1. Press the Menu Button. 2. The word OFF will appear at the bottom

SET CLOCK AUTO OFF ON OFF TIME BREW TEMP

MENU

Menu

of the LCD Control Center to indicate that the clock is not set. The programming options will appear on the LCD Control Center with a small arrow pointing to SET CLOCK (fig. 9). H (Hour) and M (Minute) will appear and blink.
3. Press or hold the blue Small Cup Button under
fig.

always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To turn the Brewer off at any time, simply press the Power Button. (NOTE: Although
the clock remains on if set, you can not brew a cup of coffee, tea or hot cocoa.)

Press the Power Button again to restore power to the Brewer. You will have to wait for the water to heat up before the Brewer is ready to brew.

3. Program your Brewer for a specific On/Off Time. NOTE: To use this programming feature, the clock must be set to the correct time. The clock will not be displayed unless the time is set.
fig.

fig.

14

10

2. Set the Brewer to Auto Off following a specified period of time after the last brew.

12

Set Hours

Set Minutes 4. Press or hold the blue Large Mug Button under the blinking M to set the minutes.

the blinking H until you have reached the appropriate hour. If the hour has passed 12, the indicator switches from AM to PM.

a. Press the Menu Button twice to program the Auto Off feature. The LCD Control Center will display the programming options with a small arrow next to SET AUTO OFF (fig. 10).
CLOCK SET AUTO OFF ON OFF TIME BREW TEMP

a. After setting the correct time (required), press the Menu Button three times to program the On Time feature. The LCD Control Center will show the programming options with a small arrow next to SET ON TIME (fig. 12).
CLOCK AUTO OFF SET ON TIME BREW TEMP
PM 11: 56 AM

READY TO BREW
AUTO OFF SET ON TIME SET

11: 56 AM
MENU

5. When you have reached the correct time, press the Menu Button five

MENU

times to scroll through the remaining programming options and exit the programming mode.
6. The correct time should now be displayed in the LCD Control Center. NOTE: If power is interrupted to the Brewer by unplugging it, or if power is lost, follow the procedure above to reset the time as the clock will not be visible until the time is set.

b. Press or hold the blue Small Cup Button under the blinking H to advance 1 hour at a time, up to 9 hours.

MENU

b. Press or hold the blue Small Cup Button under the H to scroll through the hours to your desired ON TIME hour. c. Press or hold the blue Large Mug Button under the M to scroll through the minutes to your desired ON TIME minutes.

Menu x2

d. After setting the desired time, press the Menu Button to save the ON TIME and move to the SET OFF TIME (fig. 13). 10 11

NOTE: The AUTO OFF Timer and the On/Off Time programming options operate independently but can also be programmed to work together. For example, you can set the On Time function to turn on at 7:00 AM and then set the Auto Off Timer function to turn off the Brewer two hours after the last brew (fig. 14).

SECTION 2 Controls & Indicators (LCD Control Center)

SECTION 3

Cleaning & Maintenance

fig.

17 2. Cleaning the FunnelThe Funnel can be

Programming Brew Temperature (187192 F)

The Brewer brews at a preset temperature of 192. You can adjust this temperature down by 5 degrees if you prefer a cooler cup of coffee, tea or hot cocoa. Simply follow the instructions below.
1. Press the Menu Button on the LCD Control Center five times to

Cleaning External Parts

Regular cleaning of the Brewers external components is recommended.
1. Never immerse the Brewer in water or other liquids. The Housing and

removed from the K-Cup Pack Holder by pulling on it until it snaps off (fig. 17). The Funnel is dishwasher safe. To replace it, just snap it back onto the K-Cup Pack Holder Assembly.

1. Rinse the filter screen with the strong force of water from your faucet. 2. If you have a sprayer, aim the water spray at the filter screen. 3. Fill the Water Reservoir with approximately two inches of clean water

and agitate (shake) the Water Reservoir. Empty the Water Reservoir then fill it with clean water and return it to the Brewer. If needed, repeat above procedures. CAUTION: Please rinse the Water Reservoir
thoroughly after cleaning. This will ensure that no cleaners or cleaning solutions remain as they may contaminate the water supply in the Brewer.

3. Cleaning the Exit NeedleThe Exit Needle is

other external components may be cleaned with a soapy, damp, non-abrasive cloth.
2. The Drip Tray can accumulate up to 8 oz. of overflow. The Drip Tray

program the Brew Temperature feature.

2. The LCD Control Center will now display the programming options with

a small arrow next to SET BREWTEMP (fig. 15). Also, the temperature 192 (initial setting) will be indicated at the bottom of the LCD Control Center to indicate the current temperature setting.
3. A minus sign will appear over the Small Cup Button and/or a plus sign

and Drip Tray Plate should be periodically inspected and rinsed clean. To remove the Drip Tray Assembly, simply slide it toward you, keeping it level at all times to avoid spilling. The Drip Tray and Drip Tray Plate should not be placed in the dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth and rinsed thoroughly.

located on the inside bottom of the K-Cup Pack Holder Assembly. Should a clog arise due to coffee grinds, it can be cleaned using a paper clip or similar tool. Remove K-Cup Pack Holder Assembly and detach Funnel. Insert the paper clip (fig. 17) into the Exit Needle to loosen the clog and push it out. The K-Cup Pack Holder is dishwasher safe. CAUTION: There are sharp

De-Scaling Your Brewer

Mineral content in water varies from place to place. Depending on the mineral content of the water in your area, calcium deposits or scale may build up in your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer performance. De-scaling your Brewer helps maintain the heating element and other internal parts of the Brewer that come in contact with water. The Brewer should be de-scaled every 3-6 months to ensure optimal performance. It is possible for calcium deposits to build up faster, making it necessary to de-scale more often. You should promptly de-scale if DE-SCALE is indicated on the LCD Control Center (fig. 18). However, even if DE-SCALE is not indicated, you should continue to de-scale your Brewer every 3-6 months. Properly follow the de-scaling procedure described on page 14.

over the Large Mug Button. Use these buttons to raise or lower the temperature one degree at a time.
fig.

Cleaning the K-Cup Pack Holder Assembly

fig.

needles that puncture the K-Cup pack above the K-Cup Pack Holder and in the bottom of the K-Cup Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup Pack Assembly Housing.

15

4. Once you have reached your desired brew

CLOCK AUTO OFF ON OFF TIME SET BREW TEMP

temperature, press the Menu Button once to exit the programming mode. BREW TEMP SET will be indicated in the LCD Control Center if you have changed it from 192.
5. To change the brew temperature again, repeat

16

1. Cleaning the PartsThe K-Cup Pack Holder

Cleaning the Water Reservoir & Water Reservoir Lid

The Water Reservoir Lid and Water Reservoir should be periodically inspected and cleaned. The Water Reservoir Lid or Water Reservoir should not be put into the dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth and rinsed thoroughly. Do not dry the inside of the Water Reservoir with a cloth as lint may remain. To clean the filter screen at the base of your Water Reservoir, empty the Water Reservoir and follow one or all of the following procedures.
NOTE: If you are using a water filter inside the Water Reservoir, remove it before cleaning.

MENU

192

steps 1 through 3 to change the temperature up or down, remembering that the temperature can only be between 187 and 192 .

Assembly can be placed onto the top shelf of a dishwasher. NOTE: Use low temperature cycles in the dishwasher. To remove from the Brewer, open the cover by lifting the Handle. Grasp the top of the K-Cup Pack Holder with one hand while pushing up on the bottom of the K-Cup Pack Holder from underneath with the other until it releases (fig. 16). After cleaning, align the K-Cup Pack Holder with the opening using the two front ribs as a guide, and snap into place from the top.

fig.

18

DE-SCALE
MENU

11: 56 AM

12

13

SECTION 3 Cleaning & Maintenance (continued)

SECTION 4
Service
Beyond these recommended cleaning and maintenance procedures, this Brewer is not user serviceable. For service, please refer to the Warranty section of this guide. SituAtion Brewer does not have power

Troubleshooting
SituAtion Brewing a partial cup Solution
The Exit Needle may be clogged (refer to page 13).  Clean the K-Cup Pack Holder if necessary and rinse  The Water Reservoir may have been removed during

De-Scaling Instructions
A. PREPARE

Solution
Plug Brewer into an independent outlet. Check to be sure that it is plugged in securely. Plug into a different outlet. Reset your homes circuit breaker, if necessary.  Make sure that the Power Button has

Step 1:  To begin, you will need the following: At least 48 oz. of undiluted white vinegar Access to an empty sink A large ceramic mug (do not use a paper cup)

under faucet (refer to page 12).

Step 2: Empty the water from the Water Reservoir. Step 3: Disable Auto Off features. Step 1: Pour approximately 48 oz. of the vinegar into the Water Reservoir. Step 2:  Place a large mug on the Drip Tray Plate and run a cleansing brew. DO NOT USE A K-CUP PACK, just press a Brew Button. Pour the contents of the large mug into the sink. Step 3:  Repeat the brew process without a K-Cup pack until ADD WATER is indicated.

Storage
Empty the Water Reservoir before storing, and take care to ensure that you store your Brewer in a safe and frost free environment. Please be sure to store your Brewer in its upright position to avoid water leakage from the inner tank. If you store the Brewer in a cold environment, you run the risk of water freezing inside the Brewer and causing damage. When you prepare to use it after storage, we recommend rinsing the Water Reservoir with fresh water and running three cleansing brews without a K-Cup pack. If you plan to move your Brewer to a different location, turn the Brewer off, unplug it, and empty the Water Reservoir. If your Brewer has been in an environment below freezing, please be sure to let it warm to room temperature for at least 2 hours before using. Brewer will not brew

been turned on.

 After placing the K-Cup pack in the K-Cup Pack Holder,

B. FILL AND CLEAN

Step 4: Now let the Brewer stand for at least 4 hours while still on. Step 5:  Discard any residual vinegar and rinse the Water Reservoir thoroughly. Step 1: Ensure the Water Reservoir is filled with fresh water. Step 2:  Place a large mug on the Drip Tray Plate and run a cleansing brew. Pour the contents of the large mug into the sink. Step 3: Repeat brew process until ADD WATER is indicated. Step 4:  You may need to perform additional cleansing brews if you notice any residual taste.
NOTE: If DE-SCALE is still indicated after completing the procedure, repeat the de-scaling procedure above. C. RINSE

make sure the Handle is pushed down securely and the LCD Control Center indicates READY TO BREW with the three Brew Buttons blinking, then press the Small Cup, Small Mug or Large Mug Button.  If the LCD Control Center indicates ADD WATER, add water to the Water Reservoir or make sure the Water Reservoir is seated properly in its base.  If the LCD Control Center indicates ADD WATER even after refilling, contact Customer Service at 1.866.901.BREW (2739). The Exit Needle may be clogged (refer to page 13).  If the LCD Control Center indicates PRIME and the blue light in the Water Reservoir is flashing, see below.

brewing. Replace the Water Reservoir and perform a cleansing brew without a K-Cup pack.  De-scale the Brewer (refer to page 13).  If you have repeated the de-scale procedure on your Brewer two times and it is still only brewing a partial cup, contact Customer Service at 1.866.901.BREW (2739). The time is not displayed on the LCD Control Center
 The time will not be displayed on the LCD Control

Center unless you have set it. To set the clock, follow the procedure on page 10.  If power is interrupted to the Brewer, you will need to set the clock again using the procedure on page 10.
 Check to make sure that the Auto Off Timer

My Brewer shuts off or turns on automatically

LCD Control Center  Completely remove the Water Reservoir and indicates PRIME thoroughly clean (refer to page 13). Ensure the and the blue light in Water Reservoir is fully filled with water. Return it to the Water Reservoir the Brewer and ensure it is seated properly. is flashing  If you have completed the above proceduretwo times and this situation persists, contact Customer Service at 1.866.901.BREW (2739). 14 15

and/or On/Off Time features have not been set. To do this, press the Menu Button and scroll through the programming options. OFF should be indicated for Auto Off Timer and On/Off. If OFF is not indicated, follow directions on page 10 to reset.

If any problems persist, contact Customer Service at 1.866.901.BREW (2739)

SECTION 5

Warranty
Nor does this warranty cover damages caused by use of non Keurig Brewed K-Cup brand packs or accessories, services performed by anyone other than Keurig or its authorized service providers, use of parts other than genuine Keurig parts, or external causes such as abuse, misuse, inappropriate power supply or acts of God.
Other Limitations

Limited One Year Warranty

Keurig, Incorporated warrants that your Brewer will be free of defects in materials or workmanship under normal home use for one year from the date of purchase. It is recommended that you fill out and return the warranty card enclosed with your Brewer so that your purchase information will be stored in our system. Keurig will, at its option, repair or replace a defective Brewer without charge upon its receipt of proof of the date of purchase. If a replacement Brewer is necessary to service this warranty, the replacement Brewer may be new or reconditioned. If a replacement Brewer is sent, a new limited one year warranty will be applied to the replacement Brewer. This warranty only applies to Brewers operated in the United States and Canada. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state and, in the case of Canada, from province to province. Only the use of Keurig Brewed K-Cup brand packs and accessories will guarantee the proper functioning and lifetime of your Keurig Brewer. Any damage to or malfunction of your Brewer resulting from the use of non Keurig Brewed K-Cup brand packs and accessories may not be covered by this warranty or may result in a service fee if the damage or malfunction is determined to be caused by such use.
What is not covered by the Limited Warranty?

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR B60 BREWER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you depending on the state or the province of purchase.
How do you obtain warranty service?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you depending on the state or province of purchase.

Keurig Brewers are high-quality appliances and, with proper care, are intended to provide years of satisfying performance. However, should the need arise for warranty servicing, simply call Keurig Customer Service at our toll free phone number 1.866.901.BREW (2739). Please do not return your Brewer for servicing without first speaking to Keurig Customer Service to obtain an Authorization to Return number (ATR). Keurig Brewers returned without an ATR number will be returned to the sender without servicing. Keurig, Incorporated 55 Walkers Brook Drive Reading, MA 01867 1.866.901.BREW (2739) 16

P/N 60-201204-000 Rev E 07/12

CLICK, CALL OR SHOP I www.keurig.com I 1.866.901.BREW I At over 18,000 stores in the U.S. and Canada

Keurig, Incorporated 55 Walkers Brook Drive Reading, MA 01867 Keurig, Incorporated is a  wholly-owned subsidiary of Green Mountain Coffee Roasters, Inc.

For Household Use Only Covered by U.S. Patent Numbers D513,572; D544,299; 7,165,488; 7,347,138; 7,398,726; 7,377,162; 7,360,418; 7,513,192; and 8,151,694.

2012 Keurig, Incorporated All rights reserved