GX-BT7

SERVICE MANUAL
No. S2403GXBT7U//

WIRELESS BLUETOOTH SPEAKER SYSTEM

MODEL
MUTE ON/ ECO MODE STAND-BY BASS TREBLE VOL PAIRING E SOUND BLUETOOTH AUDIO IN USB DIMMER
RRMCGA342AWSA

GX-BT7

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used.

iPad, iPhone, iPod, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries Lightning is a trademark of Apple Inc. Made for iPod, Made for iPhone, and Made for iPad mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and trade names are those of their respective owners. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Android is a trademark of Google Inc.

CONTENTS
PRECAUTIONS FOR USING LEAD-FREE SOLDER CHAPTER 1. GENERAL DESCRIPTION [1] Important Ser vice Safety Precaution........... 1-1 [2] Important Ser vice Note (for U.S.A only) ...... 1-1 [3] Specifications .............................................. 1-2 [4] Controls and indicators................................ 1-3 CHAPTER 2. ADJUSTMENTS [1] Version Check ............................................. 2-1 [2] NFC Tag Writing Procedure ........................ 2-1 CHAPTER 3. MECHANISM DESCRIPTION [1] Disassembly ................................................ 3-1 CHAPTER 4. MAJOR PART DRAWING [1] Function Table of IC..................................... 4-1 CHAPTER 5. CIRCUIT DESCRIPTION [1] IC Voltage .................................................... 5-1 CHAPTER 6. DIAGRAM [1] Main/Amplifier Block Diagram ..................... 6-1 [2] Voltage And Current Block Diagram ............ 6-2 CHAPTER 7. CIRCUIT SCHEMATICS AND PARTS LAYOUT [1] Notes On Schematic Diagram ..................... 7-1 [2] Types Of Transistor And LED ...................... 7-1 [3] Schematic Diagram ..................................... 7-2 [4] Chart Of Connecting Wires ......................... 7-4 [5] Wiring Side Of PWB .................................... 7-5 PARTS GUIDE

Parts marked with ! are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION
1

This document has been published to be used for after sales service only. The contents are subject to change without notice.

GX-BT7
PRECAUTIONS FOR USING LEAD-FREE SOLDER
1. Employing lead-free solder MAIN, KEY, LED DRIVER, REMOTE SENSOR, SWITCH, SMPS, NFC Tag PWB of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWB and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:

Indicates lead-free solder of tin, silver and copper. 2. Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks. As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area. 3. Soldering As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has poor solder wet ability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition. Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it. When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper. Be careful when replacing parts with polarity indication on the PWB silk. Lead-free wire solder for servicing
Ref No. PWB-A PWB-B Parts No. 92LPWB8945 MANS RUiTZA115AWZZ GCASP8945AW01 Description MAIN (A1) / KEY (A2) / LED DRIVER (A3) / REMOTE SENSOR (A4) / SWITCH (A5) SMPS NFC Tag

NOTE: Please refer to Parts Guide for PWB Service Category

2 i

GX-BT7

CHAPTER 1. GENERAL DESCRIPTION

[1] Important Service Safety Precaution CAUTION : These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. WARNING 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing.

[2] Important Service Notes (for U.S.A only)

BEFORE RETURNING THE AUDIO PRODUCT

(Fire & Shock Hazard) Before returning the audio product to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the audio product. 2. Inspect all protective devices such as insulating materials, cabinet, terminal board, adjustment and compartment covers or shields, mechanical insulators etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. * Plug the AC line cord directly into a 120 volt AC outlet. * Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15F capacitor in series with all exposed metal cabinet parts and a known earth ground, such as conduit or electrical ground connected to earth ground. * Use a VTVM or VOM with 1000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor (See diagram). * Connect the resistor connection to all exposed metal parts having a return path to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.
0.15 F TEST PROBE TO EXPOSED METAL PARTS

VTVM AC SCALE

1.5k ohms 10W

CONNECT TO KNOWN EARTH GROUND

All check must be repeated with the AC line cord plug connection reversed. Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp. AC.) Or more is excessive and indicates a potential shock hazard which must be corrected before returning the audio product to the owner.

1 3 1

GX-BT7
[3] Specifications
As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifi cation figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

USB (MP3 / WMA)

USB host interface Complies with USB 1.1 (Full Speed)/2.0 Mass Storage Class. Support Bulk only and CBI protocol. MPEG 1 Layer 3 WMA (Non DRM) MP3 (32 ~ 320 kbps) WMA (64 ~ 160 kbps) Maximum total number of MP3/ WMA files is 65025. Maximum total number of folders is 999 INCLUSIVE of root directory. Support USB devices with Microsoft Windows/DOS/FAT 12/ FAT 16/FAT 32. 2 kbyte block length for sector.

Support file Bitrate support Other

General
Power source Power consumption Dimensions AC 100 - 240 V ~ 50/60 Hz AC: Power on: 21 W Width: 17 - 9/16 (446 mm) Height: 6 - 1/8 (155 mm) Depth: 6 - 1/16 (154 mm)
File system support

Weight 6.0 lbs. (2.7 kg) Frequency band 2.400 GHz - 2.480 GHz Compatible A2DP (Advanced Audio Distribution Bluetooth Profile Profile), AVRCP (Audio/ Video Remote Control Profile) Bluetooth 2.1 +EDR

Speaker
Type 2-way type speaker system Front Speakers: 2 (5 cm) - 3 - Full Range Subwoofer: 3-1/8 (8 cm) - 6 - woofer Front Speakers: 10 W / Channel Subwoofer: 10 W / Channel Front Speakers: 5 W / Channel Subwoofer: 5 W / Channel

Amplifier
Output power Front speaker: RMS: Total 10 W (5 W per channel into 3 ohms at 1 kHz, 10% T.H.D.) FTC: 4 W minimum RMS per channel into 3 ohms from 200 Hz to 15 kHz, 10% T.H.D. Subwoofer: RMS: Total 10 W 6 ohms at 100 Hz, 10% T.H.D.) FTC: 10 W minimum RMS into 6 ohms from 60 Hz to 150 Hz, 10% T.H.D Audio In (audio signal): 500 mV/47 k ohms

Maximum input power Rated input power

Input terminals

1 4 2

GX-BT7
[4] Controls and indicators
1 2 3 4 5 6

Front panel
1. Audio in jack 2. Power On/Standby Button 3. ESound Button 4. USB terminal 5. Function Button 6. Pairing Button 7. Volume Down Button 8. Volume Up Button 9. LED light 10. Remote Sensor 11. USB indicator 12. Bluetooth/Pairing indicator

10

11

12

1 5 3

GX-BT7
1
MUTE

Remote control
14 15 1. Eco Mode Button 2. Mute Button 3. Treble + Button 4. Bass + Button 5. Treble - Button 6. Bass - Button 7. Pairing Button 8. Audio In Button 9. Bluetooth Button 10. Play/Pause Button 11. Skip down Button 12. Stop Button 13. Dimmer Button 14. On/Stand-by Button 15. Volume Up Button 16. Volume Down Button 17. Esound Button 18. USB Button 19. Skip up Button Note:

ON/ ECO MODE STAND-BY

2 3 4 5 6 7 8 9 10 11 12 13

BASS

TREBLE

VOL

16
PAIRING E SOUND

17
BLUETOOTH AUDIO IN
USB

18 19
DIMMER

RRMCGA342AWSA

Remote control

Plastic shield

Battery holder

Before using the remote control, remove the plastic shield from the battery holder.

Speakers
1. Front speaker 2. Subwoofer 3. Bass Reflex Duct

1 6 4

GX-BT7

CHAPTER 2. ADJUSTMENTS
[1] Version Check 1.Version checking method
1. During Audio In function, press button (remote control) then press and hold LEDs light up to indicate software version. button (remote control) until

2. Software version display

Since this model has no FL display, LED is used to indicate software version by light up or no. of blinks.
Example for software version display:
No. of Blinks (2Hz) Version v003 v099 v102 v115 Running LEDs OFF OFF ON ON USB_LED (orange) X 9 X 1 PAIRING_LED (blue) 3 9 2 5

3. Exiting Version Check

3.1. While in Version display, press ON / STAND-BY button (remote/main unit). Micom is reset then go to Bluetooth Stand-by Mode.

21

GX-BT7
[2] NFC Tag Writing Procedure
This product comes with 2 identical NFC tags. Partcode : GCASP8945AW01 NFC tag has unique Bluetooth MAC ID for each individual set. This unique ID corresponds to the Serial No. of each set. Factory provides a database of the corresponding Bluetooth MAC ID for each Serial No. so that the correct ID can be rewritten onto the NFC tag when necessary. When is tag writing necessary ? Tag writing is required when there is: Irreparable damage of the tag. Loss of tag. Tag replacement and servicing expenses to be borne by customer. Defective and replacement of Bluetooth module. What customer needs to do: For replacement due to irreparable damage or loss of tag, customer needs to : inform the Serial No. of the set. For servicing on Bluetooth feature in the main unit, customer needs to : bring the main unit to service center bring the NFC tag to service center in order for the appropriate MAC ID to be rewritten.

How to write

An NFC enabled device is required; preferably a smartphone with Android Operating system of 4.1 and above. (Eg. Samsung GALAXY S4, Samsung GALAXY S3, LG Nexus 4, Sony Xperia Z) Note: Only SHARPTagWriter.apk app can be used to rewrite the tag.

1 Download SHARPTagWriter.apk file from SHARP e-Service website and install it to your NFC smartphone. Refer to your
smartphones user manual for more detail. Below is the example on the app installation process for smartphone Samsung GALAXY S4 : 1) Download SHARPTagWriter.apk file from SHARP e-Service website to your personal computer (PC). 2) On your smartphone, go to Setting Security. Check in box for Unknown sources. 3) Connect your smartphone to your PC using USB cable. If your smartphone is having difficulties or cannot connect to your PC, you may see a pop-up message on your smartphone. This message requires you to download Samsung desktop software KIES and install it to your PC. Please go to Samsung website as stated. 4) After your smartphone and PC has connected successfully, move the SHARPTagWriter.apk file from your PC into your smartphone Download folder in the phone storage as Figure 1 below : 5) On your smartphone, go to Download folder and tap on SHARPTagWriter.apk file to install the app as shown in Figure 2.

Figure 1

Figure 2

22

GX-BT7
6) A message will appear asking if you want to install the app. Tap on Install to proceed. When installation is completed, tap on Open to launch the app (refer Figure 3). SHARP Tag Writer main page will be shown as Figure 4 below.

Figure 3

Figure 4

2 Go to Setting menu by pressing on the phone left button. Then tap on Setting. (Refer Figure 5)

SHARP GX-BT7

Figure 5

Figure 6

3 Setting menu is displayed as Figure 6 above. Key in model name SHARP GX-BT7.
Note: Keep a space between SHARP and GX-BT7.

4 Check the Lock tag after write box, then tap on OK to return to main page.

Note: It is important to check the Lock tag after write box to avoid customer from rewriting the tag.

23

GX-BT7
5 On main page,
Make sure model name is correct SHARP GX-BT7. Make sure COD (Class of Device) is correct (240404) - this value is fixed. Key in address: 12 digit hexadecimal Bluetooth MAC ID (Eg. xx:xx:xx:xx:xx:xx) Each device has a unique MAC ID address assigned to each Serial No.. Refer to Serial No. vs. MAC ID database. Please email below contact person for the database : Mr. Leow Yuet Soon Customer Service Division, S&O Electronics (M) Sdn. Bhd. e-mail : [email protected]

DATA BASE
FC:58:FA:00:1C:F6 SHARP GX-BT7 SHARP GX-BT7

SHARP GX-BT7 SERIAL NO. & NFC BLUETOOTH MAC ID ITEM 1 2 3 4 5 6 7 8 9 SERIAL NO. 30700001 30700002 30700003 30700004 30700005 30700006 30700007 30700008 30700009 NFC BLUETOOTH MAC ID FC:58:FA:00:1C:F6 FC:58:FA:10:A2:22 FC:58:FA:04:67:23 FC:58:FA:50:13:12 FC:58:FA:03:16:A2 FC:58:FA:50:11:A1 FC:58:FA:06:17:F1 FC:58:FA:12:1A:F2 FC:58:FA:54:1C:F5

6 Next, the writing process can begin.

Touch the NFC smartphone onto the tag (within 2 - 3 seconds) until the screen pop up message Write tag successful appears. Information will be written into the NFC tag. Tap on OK to exit pop up message. If Fail to write tag message pops up when writing is in progress, tap on Retry and try again until successful. Note: The location of NFC antenna on a smartphones varies between brands. Refer to smartphones User Manual for more information.

FC:58:FA:00:1C:F6 SHARP GX-BT7

FC:58:FA:00:1C:F6 SHARP GX-BT7

7 NFC tag is ready to be sent to customer.

24

GX-BT7
-MEMO-

25

GX-BT7
Service Manual E Market CD-ES700/CD-ES77

CHAPTER 3. MECHANISM DESCRIPTION

[1] Disassembly Caution On Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 2. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 3. Take sufficient care on static electricity of integrated circuits and other circuits when servicing.
STEP
1 2 3

REMOVAL
Bottom Cabinet Center Frame LED Assy

PROCEDURE
1. Screw................................. (A1)x4 1. Hook................................... 1. Screw................................. 2. Screw (Black)..................... 3. Screw................................. 4. Flat Cable.......................... (B1)x4 (C1)x2 (C2)x2 (C3)x2 (C4)x2

FIGURE
1 1 2 2 2 4 3 3 3 4 4 4 4 5 6 6 5 7 7 7 7 8 8

Subwoofer (Left)

Speaker (Left) Top Cabinet

Spring (D3) x 2 PULL

Remote Sensor PWB/ 1. Screw................................. (D1)x4 Transit PWB/ 2. Screw................................. (D2)x5 3. Spring................................. (D3)x2 Switch PWB 4. Flat Cable........................... (D4)x3 5. Screw................................. (D5)x2 6. Socket ................................. (D6)x1 7. Screw ............................... (D7)x2 Key PWB 1. Screw................................. (E1)x3 2. Socket................................. (E2)x1 3. Screw................................. (E3)x3 1. Screw................................. 2. Socket................................. 3. Socket................................. 4. Screw................................. 1. Screw................................. (F1)x1 (F2)x3 (F3)x1 (F4)x4 (G1)x3

Speaker (Right) Subwoofer (Right) (D2)x3 M3x10mm (D1)x4 Screw, Special (D2)x2 M3x10mm

SMPS

7 8

Main PWB

Speaker (Left/Right)/ 1. Screw................................. (H1)x8 Subwoofer (Left/Right) 2. Screw................................. (H2)x8

Figure 3

Speaker Cabinet Assy (Left) PULL

Hook (B1) x 4 PULL

(A1)x2 M3x10mm Center Frame Top Cabinet (A1)x2 M3x10mm Bottom Cabinet PULL Speaker Cabinet Assy (Right)
(D4)x1 (C4)x2

Transit PWB

Remote Sensor PWB Switch PWB

(D7)x2 M2.6x6mm (D6)x1 (D5)x2 M2.6x8mm (D4)x2

Figure 4

Figure 1

Subwoofer (Left)

Speaker (Left) Top Cabinet Speaker (Right) Subwoofer (Right)

Subwoofer (Left)

Speaker (Left) Top Cabinet Speaker (Right) Subwoofer (Right)

(C3)x1 M2.6x8mm (C1)x2 M2.6x8mm (C3)x1 (C2-Black)x2 M2.6x8mm M2.6x8mm (E1)x3 M2.6x8mm (F1)x1 M3x10mm

Figure 2

Figure 5

31

GX-BT7
(E3)x3 M2.6x8mm

Key PWB
(E2)x1

Function Button

SPEAKER UNIT LOCKING TAB SPEAKER WIRE

Figure 6

LOCKING TAB

CAUTION:
TO REMOVE SPEAKER UNIT, PRESS THESE LOCKING TABS TO RELEASE SPEAKER WIRES.

(F2)x2 (F4)x4 M3x6mm (F2)x1 Main PWB (G1)x3 M3x6mm (H1)x4 M3x10mm Subwoofer (Left) Speaker (Left) SMPS (F3)x1 Top Cabinet Speaker (Right) (H2-Black)x4 M3x10mm Subwoofer (Right)

Figure 7

(H2-Black)x4 M3x10mm

(H1)x4 M3x10mm

Figure 8

32

GX-BT7

CHAPTER 4. MAJOR PART DRAWING

IC600 VHiOTK5262/-1 : OPTEK SOC IC (1/5)

*All GPIO Pins can be General I/O when Column Descrption3 is no define in system, GPI just can be input pin
Pin No. Pin Name
1 GPIO1[3]/SPI_MOSI

Type
EMI

Description 1
GPIO1-3

Description 2
SPI MOSI

Description 3

Description 4

GPIO1[5]/SPI_CS0

EMI

GPIO1-5

SPI port selection

GPIO1[2]/SPI_CLK

EMI

GPIO1-2

SPI Clock

GPIO1[4]/SPI_CS1

EMI

GPIO1-4

SPI port selection

GPIO1[6]/SPI_MISO

EMI

GPIO1-6

SPI MISO

GPIO0[2]/IR_INPUT

I/O

GPIO0-2

IR input detect

GPIO0[7]/SPDIF_OUT

I/O

GPIO0-7

Digital Audio SPDIF output

GPIO1[9]/PWM0_OUT/MODE1

I/O

GPIO1-9

PWM0 control output

System Working mode selection

PI32KHz

Clock

Standby mode clock input Standby mode clock output System Working mode selection

10

PO32KHz

Clock

11

GPIO1[0]/UART0_TX/MODE0

SSP

GPIO1-0

UART0 Tx

12

GPIO1[1]/UART0_RX

SSP

GPIO1-1

UART0 Rx

13

PDVDD

Power

Chip power supply

14

PVDD_1V2

Power

Chip core power supply 1.2v Chip reset

15

CHIP_RESET

I/O

16

GPI1[29]/JTDO/ROTARY_0B

GPI1-29

Debug bus JTDO

Rotary0 B

17

GPI1[12]/JTDI/ROTARY_0A

GPI1-12

Debug bus JTDI

Rotary0 A

18

GPI2[31]/JTCK/ROTARY_1B/SPDIF_IN2

GPI2-31

Debug bus JTCK

Rotary1 B

Digital Audio SPDIF2 input

19

GPI2[30]/JTMS/RORARY_1A/SPDIF_IN1

GPI2-30

Debug bus JTMS

Rotary1 A

Digital Audio SPDIF1 input

41

GX-BT7
IC600 VHiOTK5262/-1 : OPTEK SOC IC (2/5)
Pin No. Pin Name
20 PVSS

Type
Power

Description 1
Chip digital ground SDRAM address 21 SDRAM address 20 SDRAM address 24 SDRAM address 19 SDRAM address 22 SDRAM address 23 Chip power supply USB mode selection USB VBUS USB digital power supply 1.2v USB reference resistor 10k (1%) USB analog power supply 3.3v

Description 2

Description 3

Description 4

21

A21/SPI_DATA0

EMI

External SPI flash data0 External SPI flash clock External SPI flash data3 External SPI flash chip select External SPI flash data1 External SPI flash data2

22

A20/SPI_CLK

EMI

23

A24/SPI_DATA3

EMI

24

A19/SPI_CS

EMI

25

A22/SPI_DATA1

EMI

26

A23/SPI_DATA2

EMI

27

PDVDD

Power

28

USB_ID

USB

29

USB_VBUS

USB

30

VDDA_USB_1V2

USB

31

10K_1%_REF

USB

32

VCCA_USB_3V3

USB

33

USB_DM

USB

USB data M

34

USB_DP

USB

USB data P

35

AGND

Power

Chip analog ground ADC reference resistor 100k ADC channel1 input ADC channel0 input

36

ADC_RES_100K

ADC

37

ADC_CH_1

ADC

38

ADC_CH_0

ADC

39

AVSS_ADC

Power

ADC ground

40

AVDD_ADC

Power

ADC power supply

41

AVSS_PLL

Power

PLL ground

42

GX-BT7
IC600 VHiOTK5262/-1 : OPTEK SOC IC (3/5)
Pin No. Pin Name
42 AVDD_PLL

Type
Power

Description 1
PLL power supply working clock input working clock output Chip core power supply 1.2v GPIO014

Description 2

Description 3

Description 4

43

PI24MHz

Clock

44

PO24MHz

Clock

45

PVDD_1V2

Power

46

GPIO0[14]/SD_DATA0

SSP

SD card data0

47

GPIO0[12]/SD_CLK

SSP

GPIO0-13

SD card clock SD card command SD card detect

48

GPIO0[13]/SD_CMD

SSP

GPIO0-12

49

GPIO0[18]/SD_DETECT

SSP

GPIO0-18

50

GPIO0[19]/SDC_WP/NMI

SSP

GPIO0-19

SD card wp

NMI

51

GPIO0[5]/UART1_RX

SSP

GPIO0-22

52

GPIO0[9]/UART1_TX

SSP

GPIO0-9

UART1 Tx

53

GPIO0[6]/SPDIF_IN0

I/O

GPIO0-6

Digital Audio SPDIF0 input

54

GPIO0[4]/PWM_ERR

PWM

GPIO0-2

PWM error flag Multi channel mode I2S data0 output I2S channel1 data output

55

GPIO0[22]/I2S_IN_D0/MI2S_OUT_D0

I2S

GPIO0-22

I2S data0 input

56

GPIO0[25]/I2S_IN_D4/I2S_1_DOUT

I2S

GPIO0-25

I2S data4 input

57

GPIO0[27]/I2S_1_LRCK

I2S

GPIO0-27

I2S channel1 LRCK I2S channel1 BCLK I2S main clock1

58

GPIO0[26]/I2S_1_BCLK

I2S

GPIO0-26

59

GPIO0[0]/MCLK1

I2S

GPIO0-0

60

PDVDD

Power

Chip power supply

61

PDVSS

Power

Chip digital ground PWM Audio output channel1

62

GPI2[21]/CH1_PWM_N

PWM

GPI2-21

terminal N

43

GX-BT7
IC600 VHiOTK5262/-1 : OPTEK SOC IC (4/5)
Pin No. Pin Name
63 GPI2[20]/CH1_PWM_P

Type
PWM

Description 1
GPI2-20

Description 2
PWM Audio output channel1 terminal P

Description 3

Description 4

64

PVDD_1V2

Power

Chip core power supply 1.2v

65

PDVDD

Power

Chip power supply PWM Audio output channel2 terminal N PWM Audio output channel2 terminal P PWM Audio output channel3 terminal N PWM Audio output channel3 terminal P UART2 Tx

66

GPI2[23]/CH2_PWM_N

PWM

GPI2-23

67

GPI2[22]/CH2_PWM_P

PWM

GPI2-22

68

GPI2[25]/CH3_PWM_N

PWM

GPI2-25

69

GPI2[24]/CH3_PWM_P

PWM

GPI2-24

70

GPIO0[11]/UART2_TX

SSP

GPIO0-11

71

LIN

Analog

Analog Audio input channel left Analog Audio input AUX channel left

72

LAUX

Analog

73

AGND

Power

Analog ground

74

AVDD

Power

Analog power Analog Audio input AUX channel right Analog Audio input channel right Mic-phone bias input

75

RAUX

Analog

76

RIN

Analog

77

MIC_BIAS

Analog

78

VMID

Analog

VMID Headphone left channel Out Headphone right channel Out

79

HP_LOUT

Analog

80

HP_ROUT

Analog

44

GX-BT7
IC600 VHiOTK5262/-1 : OPTEK SOC IC (5/5)

78

77

76

75

74

73

72

71

70

69

68

67

66

65

64

63

62

61

80 HP_ROUT

79 HP_LOUT

RAUX

AGND

RIN

AVDD

LIN

LAUX

GPIO01[11]/UART2_TX

GPI2[25]/CH3_PWM_N

PDVSS

MIC_BIAS

GPI2[22]/CH2_PWM_P

GPI2[23]/CH2_PWM_N

GPI2[21]/CH1PWM_N

PDVDD

PVDD_1V2

GPI2[20]/CH1_PWM_P

VMID

GPI2[24]/CH3_PWM_P

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

GPIO1[3]/SPI_MOSI GPIO1[5]/SPI_CS0 GPIO1[2]/SPI_CLK GPIO1[6]/SPI_CS1 GPIO1[4]/SPI_MISO GPIO0[2]/IR_INPUT GPIO0[7]/SPDIF_OUT GPIO1[9]/PWM_OUT/MODE1 PI32KHZ PO32KHZ GPIO1[0]/UART0_TX/MODE0 GPIO1[1]/UART0_RX PDVDD PVDD_1V2 CHIP_RESET GPI1[29]/JTDO/ROTARY_0B GPI1[12]/JTDI/ROTARY_0A GPI1[31]/JTCK/ROTARY_1B/SPDIF_IN2 GPI1[30]/JTMS/ROTARY_1A/SPDIF_IN1 VDDA_USB_1V2

PDVD GPIO0[0]/MCLK1

60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

GPIO0[26]/I2S1_BCLK GPIO0[27]/I2S1_LRCK GPIO0[25]/I2S_IN_D4/I2S1_DOUT GPIO0[22]/I2S_IN_D0 GPIO0[4]/PWM_ERR GPIO0[6]/SPDIF_IN0

OTK5262

GPIO0[9]/UART1_TX GPIO0[5]/UART1_RX GPIO0[19]/SD_WP/NMI GPIO0[18]/SD_DETECT GPIO0[13]/SD_CMD GPIO0[12]/SD_CLK GPIO0[14]/SD_DATA0 PVDD_1V2 PO24MHZ PO24MHZ AVDD_PLL

VCCA_USB_3V3

A21/SPI_DATA0

A24/SPI_DATA3

A22/SPI_DATA1

A23/SPI_DATA2

10K_1%_REF

A20/SPI_CLK

A19/SPI_CS

ADC_RES_100K

PVSS

AVSS_PLL AVSS_ADC 39 AVDD_ADC 40

USB_VBUS

USB_DP

USB_ID

AGND

37

ADC_CH1

PDVDD

USB_DM

31

32

33

34

35

21

22

23

24

25

26

27

28

29

Figure 4-1: Pin Configuration

30

45

36

38

ADC_CH0

GX-BT7
IC601 VHIBR24T08F-1 : EEPROM

Internal Block Diagram

A0 1
8Kbit EEPROM Array 8bit

VCC

A1

Address Decoder

10bit

Word Address Register

Data Register

WP

START

STOP

A2 3

Control Circuit ACK

SCL

GND 4

High Voltage Generating Circuit

Power Source Voltage Detection

SDA

Figure 4-2: Block Diagram

Figure 4-3: Pin Configuration

A0

1 2

Vcc

A1 A2

WP SCL SDA

TOP VIEW
3 6 5

GND

Pin Descriptions
Terminal Name A0 A1 A2 GND SDA SCL WP VCC Input/ Output Input Input/ Output Input Input Dont use (1) Dont use (1) Slave address setting Reference voltage of all input / output, 0V Serial data input serial data output Serial clock input Write protect terminal Connect the power source Descriptions

(1) Pins not used as device address may be set to any of H, L, and Hi-Z.

46

GX-BT7
IC603 RH-iXA380AW00 : 8M-BIT SERIAL FLASH MEMORY IC (1/1)

/CS DO(IO 1 ) /WP(IO2 ) GND

1 2 3 4

8 7 6 5

VCC /HOLD(IO 0 ) CLK DI (IO0 )

Figure 4-4: Pin Configuration

PIN NO.
1 2 3 4 5 6 7 8

PIN NAME
/CS DO (IO1) /WP (IO2) GND DI (IO0) CLK /HOLD (IO3) VCC

I/O
I I/O I/O Chip Select Input

FUNCTION
Data Output (Data Input Output 1)*
1

Write Protect Input ( Data Input Output 2)*2 Ground

1

I/O I I/O

Data Input (Data Input Output 0)* Serial Clock Input Hold Input (Data Input Output 3)* Power Supply

*1 IO0 and IO1 are used for Dual and Quad instructions *2 IO0 IO3 are used for Quad instructions

47

GX-BT7
IC604 VHLED1642GW-1 : LED DRIVER IC (1/1)
GND SDI CLK LE OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 VDD R-EXT SDO PWCLK OUT15 OUT14 OUT13 OUT12 OUT11 OUT10 OUT9 OUT8

24 23 22 21 20 19 18 17 16 15 14 13

1 2 3 4 5 6 7 8 9 10 11 12

Figure 4-5: Pin Configuration Pin description

Pin 1 2 3 4 5 to 20 21 22 23 24 Symbol GND SDI CLK LE OUT0-OUT15 PWCLK SDO R-EXT VDD Name and function Ground terminal Serial Data Input terminal Clock input terminal Latch input terminal Output terminals Clock input for PWM counter Serial Data Output terminal Terminal for external resistor for constant current programming Supply voltage terminal

SDO SDI CLK LE VDD GND

PWCLK

Control Logic & Data Registers

PWM counter

OUT0

OUT1
UVLO & POR

Error detection Thermal shutdown

16 output channels

OUT2

Configuration register

R-EXT

Current Ref

Current gain adjustment

Channels driver Timing control Turn ON/OFF Gradual delay

OUT14 OUT15

Figure 4-6: Block Diagram

48

GX-BT7
IC400 VHIBA6287FE-1 : MOTOR DRIVER IC (1/1)

Figure 4-7: Block Diagram

Pin Description

49

GX-BT7
IC900 VHISTA559BW-1 : Digital Power Amplifier IC (1/2)

GND_SUB SA TEST_MODE VSS VCC_REG OUT2B GND2 VCC2 OUT2A OUT1B VCC1 GND1 OUT1A GND_REG VDD CONFIG OUT3B / FFX3B OUT3A / FFX3A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 EP, exposed pad (device ground)

36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19

VDD_DIG GND_DIG SCL SDA INT_LINE RESET SDI LRCKI BICKI XTI GND_PLL FILTER_PLL VDD_PLL PWRDN GND_DIG VDD_DIG TWARN / OUT4A EAPD / OUT4B

Figure 4-8: Pin Configuration

Pin description
Pin 1 2 3 4 5 6 7 8 9 10 Type GND I I I/O I/O O GND Power O O Name GND_SUB SA TEST_MODE VSS VCC_REG OUT2B GND2 VCC2 OUT2A OUT1B Substrate ground I2C select address (pull-down) This pin must be connected to ground (pull-down) Internal reference at VCC - 3.3 V Internal VCC reference Output half-bridge channel 2B Power negative supply Power positive supply Output half-bridge channel 2A Output half-bridge channel 1B Description

4 10

GX-BT7
IC900 VHISTA559BW-1 : Digital Power Amplifier IC (2/2)

I2C I2S interface

Protection current/thermal Channel 1A

Volume control

Power control FFX

Logic

Channel 1B

Channel 2A

Regulators PLL Bias Digital DSP Power Channel 2B

Figure 4-9: Block diagram

4 11

GX-BT7
-MEMO-

4 12

GX-BT7

CHAPTER 5. CIRCUIT DESCRIPTION

IC Voltage at Bluetooth Stand-by condition Power Supply: 100 V 60 Hz
MAIN PWB
IC 803 (V) 2.4 1 2 0 3 2.3 4 NC 5 1.3 IC 603 (V) 1 2 3 4 5 6 7 8 3.2 NC NC NC NC NC NC 3.2 IC 801 (V) 1 2 3 4 5 6 7 8 12.3 5.3 0.7 0 1.3 12.3 12.3 12.3 IC 602 (V) 1 2 3 4 5 6 7 8 0 3.1 NC NC NC 3.1 NC 3.2 IC 804 (V) 1 2 3 4 5 6 7 8 11.3 12.3 3.2 1.8 0.8 0.6 0 5.0 IC 540 (V) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 0.1 0 0 0 0 0 NC NC NC 0 NC 0 NC NC NC 0 0 0 3.3 1.8 0 3.4 NC NC ICA100 (V) NC 5.2 5.2 3.2 3.2 NC 5.2 NC NC 5.1 ICA 605 (V) IC 601 (V) 0 1 0 2 0 3 0 4 3.2 5 0 6 3.1 7 3.1 8 1 2 3 0 0 2.9 IC 802 (V) 1 2 3 NC 1.9 0 1 2 3 4 5 6 IC 800 (V) 12.3 12.3 7.4 12.3 12.3 12.3 1 2 3 4 5 6 7 8 IC 400 (V) NC 5.2 5.2 0 0 5.2 NC 0 IC 900 (V) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 0 0 0 9.1 12.3 6.2 0 6.2 6.2 6.2 6.2 6.2 6.2 0.01 0.01 0 1.6 1.6 1.6 1.6 2.6 2.6 2.6 2.6 3.4 NC NC NC NC 1.6 1.6 1.3 0.01 3.1 0 2.6 IC 560 (V) 1 2 3 4 5 6 7 8 2.3 2.3 2.3 0 2.3 2.3 NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 IC 600 (V) 0 0 0 0 3.2 3.2 3.2 1.6 1.4 1.5 0 0 3.2 1.3 2.9 0 0 0 0 0 0 0 0 3.2 0 0 3.2 0 5.2 1.3 3.2 3.2 0 0 0 0 NC 3.2 0 3.2 0 3.2 1.6 1.7 1.3 0 1.6 0.03 0 0 3.2 3.2 0 0 0 0 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 0 0 0 3.2 0 NC 0.1 1.3 3.2 3.2 3.1 0 2.9 3.2 NC NC 0 0 3.2 1.5 2.9 1.6 1.6 1.6

1 2 3 4 5 6 7 8 9 10

51

GX-BT7

CHAPTER 6. DIAGRAM
[1] Main/Amplifier Block Diagram
27 MCLK 28 BICK

I2S

29 LRCK 30 SDI 31 RESET 33 SDA 34 SCL

POWER AMP IC
OUT _2B B OUT_2A A
9

13 10

OUT_1 A OUT _1B

FRONT SPEAKER TERMINAL

IC900

Front Speaker (L-Ch) 3

Front Speaker (R-Ch) 3

SUBWOOFER SPEAKER TERMINAL

2 6

IC602
APPLE IC

Subwoofer Speaker 12

SDA

Subwoofer Speaker 12
5 6

SCL

IC601
EEPROM

Y1
24 MHz.

52

51

44

43

PI24MHZ

PO24MH

_SDA

_SCL

59 MCLK 58 BICK 57 LRCK 56 SDI 48 AMP RESET

ADC_CH_0 38 ADC_CH_1 67

KEY1 POWER KEY

Pairing, Volume Up, Volume Down, Funcon, Esound On/Standby

ICA100 IC804
USB POW EN 47

5V DCDC D+ D-

5V/3A

CURRENT LIMITER

JK580
5V/2.1A

USB Jack

USB D+ 34

IC600

USB DMOT + MOT -

33

OTK5262
JK500
L-Ch

54 46

4 5

IC400
Motor Driver BA6287

AUDIO IN Jack
R-Ch

OPEN_SW 63 CLOSE_SW 66
72 LAUX 75 RAUX

SW161/SW162
SWITCH

ADC

IC560
OP AMP

EQ Level Meter

SPI_FLASH _D2 26 SPI_FLASH _D1 25 SPI_FLASH _CS 24

3 2 1

IC603
SPI Flash IC

71 LIN 76 RIN

BT_WAKE_ _UP

SPI FLASH _D3 SPI_FLASH D3 23

PI32KHZ P032KHZ LED_CLK LED_SDI LED_LE PWCLK

7 6 5

BT_LED2

BT_VOL+

BT_VOL-

SPI_FLASH _CLK 22 SPI_FLASH _D0 21

53 5

62

12

11

IRDA
6

10

L+ LR+ R-

IC540
17 16 15 14
1

BLUETOOTH MODULE F-3088

2 6 5 4

Pairing Led (Blue) LED701 USB Led (orange) LED700

RM760
2 4 3 21

X601
32.768 kHz.

IR Sensor

NFC

IC604
LED DRIVER IC (16 port)

Running Light : Blue LED X 8 pcs (L-ch)

Running Light : Blue LED X 8 pcs (R-ch)

Figure 6-1: MAIN/AMPLIFIER BLOCK DIAGRAM

61

GX-BT7
[2] Voltage And Current Block Diagram

MCU USB_PWR

MCU USB_PWR

SMPS
12V, 2A

IC804

AC 100V~240V 50/60 Hz

DC DC CONVERTER

SW 5V, 3A

ICA100
CURRENT LIMITER

SW 5V, 2.1A

TO USB JACK

MCU DC RELAY

IC801

UNSW 5V

SW 5V

DC DC CONVERTER

Q802

TO OTK5262, BT OP AMP, RUNNING LEDs

MCU DC RELAY

IC802

UNSW 3.9V

SW 3.3V

STEP DOWN 3.3V

Q831

TO POW IC, LED DRIVER, APPLE IC

MCU DC RELAY

UNSW 3.9V SW 12V

TO POWER IC

TO BLUETOOTH

IC800
MOSFET

UNSW 3.3V

TO OTK5262, REMOCON, LEDs, SPI FLASH

SW 2.3V

IC803

UNSW 1.3V
TO OTK5262

LDO 1.3V

Figure 6-2: VOLTAGE AND CURRENT BLOCK DIAGRAM

62

GX-BT7

CHAPTER 7. CIRCUIT SCHEMATICS AND PARTS LAYOUT

[1] Notes On Schematic Diagram
Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with Fusible is a fuse type. Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression capacitance/ withstand voltage is used. (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type (P.P.): Polypropylene type PWB Switch Location
REF. NO SW770 SW776 SW777 SW778 SW779 SW780 DESCRIPTION ON/STAND-BY PAIRING FUNCTION Esound VOLUME UP (+) VOLUME DOWN (-) POSITION ON-OFF ON-OFF ON-OFF ON-OFF ON-OFF ON-OFF

Schematic diagram and Wiring Side of P.W.Board for this model are subject to change for improvement without prior notice. The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. Parts marked with are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

[2] Types Of Transistor And LED

OUT

GND

VDD

NC

E (1)

E (1)

TOP VIEW

C (2)

PST8227

KTC2875B KTC3875

KTA1544T KRC102S KRC104S KRC107S TOP VIEW TOP VIEW

SK52B RB051L SLI343YC3F M3NB2SDO

DA1010

EXA694WJ EXA720WJ EXA701WJ

A = Anode C = Cathode

71

(3) C

B (3)

(2) B

GX-BT7
[3] Schematic Diagram

MAIN PWB-A1
AUDIO IN

TO KEY PWB-A2 CNP770

TO REMOTE SENSOR PWB-A5 CNP760

TO SWITCH PWB-A5 CNP162

FOR USB EXTERNAL DEVICE ONLY

TO LED DRIVER PWB-A3 CNP604

FROM SMPS PWB-B CN2

7
Figure 7-1: MAIN SCHEMATIC DIAGRAM

10

11

12

72

GX-BT7

FROM MAIN PWB-A1 CNP602

LED DRIVER PWB-A3

A
TO LED L-CH

SWITCH PWB-A5

REMOTE SENSOR PWB-A4

TO LED R-CH

FROM MAIN PWB-A1 CNP607 FROM MAIN PWB-A1 CNP601

KEY PWB-A2

FROM MAIN PWB-A1 BI600

FROM LED DRIVER PWB-A3

FPC Connector Assy Section for Left and Right

10

11

12

Figure 7-2: KEY, LED DRIVER, REMOTE SENSOR AND SWITCH SCHEMATIC DIAGRAM

73

GX-BT7
[4] Chart Of Connecting Wires

CNS901

A
TO SPEAKER L-CH

+ -

WH BK CR3 (2 TURN)

FOR USB EXTERNAL DEVICE ONLY

AUDIO IN

TO SUBWOOFER L-CH

2 1

TO SUBWOOFER R-CH

+ -

GY BK CNS600 4 3 2 1 4 3 2 1 GY GY RD

TO SPEAKER R-CH

+ -

RD BK CR 2 (2 TURN)

RD BK WH BK

RD GY GY

2 1

+ -

GY BK GY BK

1 2 3 4

1 2 RD BR

2 4 1 3 5

6 4 2 7 5 3 1

2 4 1 3 5

FFC601

FFC607

FFC602

D
1 2 CNS800

TO LED R-Ch 1 2

CN2
FFC607 FPC [R]

TO DOOR MOTOR

RD BK

7 5 3 1 6 4 2 FFC601 5 3 1 6 4 2

1 3 5 7 9 2 4 6 8

1 2

CNS107

F
(Not Replacement Item)

8 6 4 2 9 7 5 3 1

COLOR TABLE

FPC [L]

BR RD GY BK

BROWN RED GRAY BLACK

BL BR

TO LED L-Ch

AC POWER SUPPLY CORD AC 100-240V~ 50 / 60Hz

10

11

1 2 3

1 2 3

N L

12

Figure 7-3: WIRING CONNECTION

74

GX-BT7
[5] Wiring Side Of PWB

MAIN PWB-A1

1 2 3 4

1 2

Lead-free solder indication

Lead-free solder is used in the MAIN PWB. Refer to Precautions for handling lead-free solder for instructions and precautions.

10

11

12

Figure 7-4: WIRING SIDE OF MAIN PWB (TOP VIEW)

75

GX-BT7

MAIN PWB-A1

Lead-free solder indication

Lead-free solder is used in the MAIN PWB. Refer to Precautions for handling lead-free solder for instructions and precautions.

10

11

12

Figure 7-5: WIRING SIDE OF MAIN PWB (BOTTOM VIEW)

76

GX-BT7

LED DRIVER PWB-A3

B

KEY PWB-A2

BOTTOM VIEW
D

SWITCH PWB-A5

LED DRIVER PWB-A3

REMOTE SENSOR PWB-A4

BOTTOM VIEW

BOTTOM VIEW

BOTTOM VIEW

Lead-free solder indication

Lead-free solder is used in the KEY, LED DRIVER, REMOTE SENSOR and SWITCH PWB. Refer to Precautions for handling lead-free solder for instructions and precautions.

10

11

12

Figure 7-6: WIRING SIDE OF KEY, LED DRIVER, REMOTE SENSOR AND SWITCH PWB (BOTTOM VIEW)

77

GX-BT7

KEY PWB-A2

1 2 3

TOP VIEW
D

LED DRIVER PWB-A3

E
7 5 3 1 6 4 2 1 3 5 7 9 2 4 6 8

REMOTE SENSOR PWB-A4

SWITCH PWB-A5

8 6 4 2 9 7 5 3 1 5 3 1 6 4 2

TOP VIEW TOP VIEW

TOP VIEW

Lead-free solder indication

Lead-free solder is used in the KEY, LED DRIVER, REMOTE SENSOR and SWITCH PWB. Refer to Precautions for handling lead-free solder for instructions and precautions.

10

11

12

Figure 7-7: WIRING SIDE OF KEY, LED DRIVER, REMOTE SENSOR AND SWITCH PWB (TOP VIEW)

78

GX-BT7
-MEMO-

79

GX-BT7

PARTS GUIDE
WIRELESS BLUETOOTH SPEAKER SYSTEM

MODEL

GX-BT7

CONTENTS
[1] [2] [3] [4] [5] [6] INTEGRATED CIRCUITS TRANSISTORS DIODES COILS CRYSTALS / VIBRATORS CAPACITORS [7] [8] [9] RESISTORS OTHER CIRCUITRY PARTS CABINET PARTS / CD MECHANISM PARTS

[10] ACCESSORIES / PACKING PARTS [11] P.W.B. ASSEMBLY

Explanation of capacitors/resistors parts codes

Capacitors
VCC ....................... Ceramic type VCK ........................ Ceramic type VCT ........................ Semiconductor type VC MF ............... Cylindrical type (without lead wire) VC MN ............... Cylindrical type (without lead wire) VC TV ................ Square type (without lead wire) VC TQ ............... Square type (without lead wire) VC CY ............... Square type (without lead wire) VC CZ ............... Square type (without lead wire) VC J .. The 13th character represents capacity difference. ("J" 5%, "K" 10%, "M" 20%, "N" 30%, "C" 0.25 pF, "D" 0.5 pF, "Z" +80-20%.) If there are no indications for the electrolytic capacitors, error is 20%.

Resistors
VRD ....................... Carbon-film type VRS ........................ Carbon-film type VRN ....................... Metal-film type VR MF ............... Cylindrical type (without lead wire) VR MN ............... Cylindrical type (without lead wire) VR TV ................ Square type (without lead wire) VR TQ ............... Square type (without lead wire) VR CY ............... Square type (without lead wire) VR CZ ............... Square type (without lead wire) VR J .. The 13th character represents error. ("J" 5%, "F" 1%, "D" 0.5%.) If there are no indications for other parts, the resistors are 5% carbon-film type.

Explanation of PWB Assembly parts code category

S Category X Category -- Repair ( Component parts of PWB can be replace and repair, PWB no supply ) -- Replacement ( PWB can not be repair. Component parts no supply )

S.X Category -- Repair and Replacement ( PWB can repair and replace ) KG Category -- Revolve repair by Business Center ( Return to Business Center and repair by manufacturer. Component parts no supply )

Parts marked with " ! " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used for after sales service only. The contents are subject to change without notice.

GX-BT7
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

[1] INTEGRATED CIRCUITS

IC 400 IC 540 IC 560 IC 600 IC 601 IC 602 IC 603 IC 604 IC 800 IC 801 IC 802 IC 803 IC 804 IC 900 IC A 100 IC A 605 V H IB A 6287F E -1 ------------V H IU T C 4580E -1 V H IO T K 5262/-1 V H IB R 24T 08F -1 V H I337S 3959-1 R H -IXA 380A W 00 V H LE D 1642G W -1 V S N T G S 3136P -1 V H IM C 33063A -1 V H IU T C 1117Y 33 V H IT C R 2E F 13-1 V H IT P S 54331-1 V H IS T A 559B W -1 V H IT P S 2561D -1 V H IP S T 8227U -1 AG -AC AY AD AM AL AH AG AE AD AC AF AM AH AC M otor D river IC B A 6287 B luetooth M odule F -308 [Not Serviceable Item] D ual O P A M P IC U T C 4580 O P T E K S O C IC O T K 5262 E E P R O M IC IP O D A uthentication IC F lash Memory IC, 8M-Bit LE D D river IC P-Channel MOS F E T 2 0 V 5 . 8 A D C -D C IC 18V (S tep up) Low D rop R egulator IC 3.3V 1A LD O R egulator IC 1.3V Input D C -D C 28V 3A P ow er A m p IC S T A 559B W C R T Lim iter P ow er S w itch R eset IC 2.7V

[2] TRANSISTORS
Q 541 Q 760 Q 761 Q 800 Q 801 Q 802 Q 830 Q 831 Q 833 Q A 610 Q A 611 Q A 612 Q A 616 V S K T C 3875G R -1 V S K R C 107S //-1 V S K R C 107S //-1 V S K R C 107S //-1 V S K R C 102S //-1 V S K M A 2D 4P 20-1 V S K R C 102S //-1 V S K T A 1544T /-1 V S K R C 102S //-1 V S K R A 107S //-1 V S K T C 2875B /-1 V S K T C 2875B /-1 V S K R C 104S //-1 AB AB AB AB AB AD AB AD AB AB AC AC AC N P N T ransistor K T C 3875G R N P N T ransistor K R C 107S N P N T ransistor K R C 107S N P N T ransistor K R C 107S N P N T ransistor K R C 102S MO SFET Transistor N P N T ransistor K R C 102S P N P T ransistor K T A 1544T N P N T ransistor K R C 102S P N P T ransistor K R A 107S N P N T ransistor K T C 2875G B N P N T ransistor K T C 2875G B N P N T ransistor K R C 104S

[3] DIODES
D504 D505 D542 D700 D801 D802 D830 D831 D832 D834 D835 D836 D853 D854 DA610 DA615 DZ800 DZ801 DZ810 DZ830 LED700 LED701 VHDDA1010++-1 VHDDA1010++-1 VHDGS1GLTP+-1 VHDDA1010++-1 VHDDA1010++-1 VHDDA1010++-1 VHDDA1010++-1 VHDGS1GLTP+-1 VHDGS1GLTP+-1 VHDGS1GLTP+-1 VHDGS1GLTP+-1 VHDSX34R2++-1 VHDDA1010++-1 VHDGDSK52B+-1 VHDDA1010++-1 VHDDA1010++-1 RH-EXA701WJQZ RH-EXA720WJQZ VHDGDSK14++-1 RH-EXA694WJQZ VHPSLI343YC3F VHPM3NB2SDO-1 AB AB AB AB AB AB AB AB AB AB AB AB AE AB AB AB AB AC AB AD AE Switching Diode DA1010 Switching Diode DA1010 Surface Mount Rectifier Switching Diode DA1010 Switching Diode DA1010 Switching Diode DA1010 Switching Diode DA1010 Surface Mount Rectifier Surface Mount Rectifier Surface Mount Rectifier Surface Mount Rectifier Schottky Diode Switching Diode DA1010 Schottky Diode Schottky Diode Schottky Diode Zener Diode 6.8V 5.0mA Zener Diode Schottky Diode Zener Diode Yellow LED Blue LED

[4] COILS
CR2 CR3 F B 601 F B 602 F B 603 F B 605 F B 606 F B 621 F B 622 F B 623 F B 624 F B 625 F B 626 F B 656 F B 657 F B 658 F B 659 F B 800 L200 L802 L810 L940 L941 L942 L943 L944 L945 L946 R 961 R 962 R C O R F A 046A W Z Z R C O R F A 046A W Z Z R B LN -A 016A W Z Z R B LN -A 016A W Z Z R B LN -A 016A W Z Z R B LN -0077T A Z Z R B LN -0077T A Z Z R F ILN A 026A F Z Z R F ILN A 026A F Z Z R F ILN A 026A F Z Z R F ILN A 026A F Z Z R F ILN A 026A F Z Z R F ILN A 026A F Z Z R B LN -A 016A W Z Z R B LN -A 016A W Z Z R B LN -A 016A W Z Z R B LN -A 016A W Z Z R F ILN A 025A W Z Z R B LN -0006T A Z Z R C ILZ A 089A W Z Z R C ILP A 349W JP Z R C ILP A 761W JQ Z R C ILP A 761W JQ Z R C ILP A 761W JQ Z R C ILP A 761W JQ Z R C ILZ A 087W JZ Z R C ILZ A 087W JZ Z R C ILZ A 087W JZ Z R F ILN A 009A W Z Z R F ILN A 009A W Z Z AA AA AA AB AB AB AB AB AB AB AB AA AA AA AA AD AA AF AF AD AD AD AD AG AG AG AB AB F errite C ore, R ing F errite C ore, R ing F errite bead F errite bead F errite bead C hip F errite bead, B A LU N C hip F errite bead, B A LU N F errite bead, F ilter F errite bead, F ilter F errite bead, F ilter F errite bead, F ilter F errite bead, F ilter F errite bead, F ilter F errite bead F errite bead F errite bead F errite bead F errite bead C hip F errite bead, B A LU N Inductor S M D C oil 220uH F errite bead, 22uH F errite bead, 22uH F errite bead, 22uH F errite bead, 22uH C hok e C oil C hok e C oil C hok e C oil C hip F errite bead 600O hm C hip F errite bead 600O hm

GX-BT7
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

[5] CRYSTALS / VIBRATORS

X601 Y1 R C R S P A 037A W Z Z R C R S P A 050A W Z Z AD AD C rystal 32.768K H z C rystal 24M H z

[6] CAPACITORS
C2 C 10 C 24 C 99 C 210 C 214 C 400 C 502 C 503 C 506 C 507 C 541 C 543 C 545 C 546 C 547 C 561 C 562 C 563 C 581 C 582 C 583 C 600 C 601 C 602 C 603 C 604 C 605 C 606 C 607 C 608 C 609 C 610 C 611 C 612 C 613 C 616 C 617 C 618 C 620 C 621 C 640 C 760 C 761 C 770 C 772 C 801 C 803 C 810 C 811 C 812 C 831 C 833 C 840 C 841 C 843 C 845 C 846 C 847 C 848 C 901 C 902 C 903 C 904 C 906 C 907 C 909 C 911 C 912 C 914 C 915 C 919 C 920 C 921 C 922 C 923 C 924 C 925 C 926 C 927 C 928 C 929 V C C C C Y 1H H 270J V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 0JB 106K V C K Y C Y 1A B 225K V C K Y C Y 1A B 225K V C K Y C Y 1H B 104K V C C C C Y 1H H 330J V C C C C Y 1H H 330J V C K Y C Y 1A B 225K V C K Y C Y 1A B 225K V C K Y C Y 1H B 104K V C K Y C Y 1E B 105K V C K Y C Y 1E B 105K V C K Y C Y 1E B 105K V C K Y C Y 1E B 105K V C C C C Y 1H H 330J V C C C C Y 1H H 330J V C K Y C Y 1A B 225K V C K Y C Y 1H B 223K V C C C C Z 1H H 5R 0C V C C C C Z 1H H 5R 0C V C K Y C Y 1H B 104K V C C C C Y 1H H 150J V C C C C Y 1H H 150J V C K Y C Z 1E F 104Z V C K Y C Z 1E F 104Z V C K Y C Z 1A B 225K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Z 1E F 104Z V C K Y C Y 1H B 104K V C K Y C Z 1E F 104Z V C C C C Z 1H H 180J V C C C C Z 1H H 180J V C K Y C Z 1E F 104Z V C K Y C Z 1E F 104Z V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K R C -K Z A 214W JZ Z V C K Y C Y 1H B 104K V C C C C Y 1H H 151J V C K Y C Y 1H B 223K V C K Y C Y 1H B 102K V C K Y C Y 1H B 102K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y T V 1H B 471K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1E B 105K V C K Y C Y 1E B 105K V C K Y C Y 1H B 153K V C K Y C Y 1H B 182K V C C C C Y 1H H 120J V C K Y T V 1E B 106K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Z 1H B 472K V C K Y C Z 1H B 681K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y T V 1H B 104K V C K Y T V 1H B 104K V C K Y C Y 1H B 102K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Y 1E B 105K V C K Y C Y 1E B 105K V C K Y C Y 1H B 104K AA AD AD AB AB AB AD AA AA AB AB AD AB AB AB AB AA AA AB AA AB AB AD AA AA AA AA AB AD AD AA AD AA AA AA AA AA AD AD AD AD AD AA AA AA AA AD AD AD AA AD AD AD AB AB AA AA AA AC AD AD AD AD AD AC AB AD AD AD AD AD AA AD AD AD AD AD AD AD AB AB AD 27 pF ,50V 0.1 F ,50V 0.1 F ,50V 10 F ,6.3V 2.2 F ,50V 2.2 F ,10V 0.1 F ,50V 33 pF ,50V 33 pF ,50V 2.2 F ,10V 2.2 F ,10V 0.1 F ,50V 1 F ,25V 1 F ,25V 1 F ,25V 1 F ,25V 33 pF ,50V 33 pF ,50V 2.2 F ,10V 0.022 F ,50V 5 pF ,50V 5 pF ,50V 0.1 F ,50V 15 pF ,50V 15 pF ,50V 0.1 F ,25V 0.1 F ,25V 2.2 F ,10V 0.1 F ,50V 0.1 F ,50V 0.1 F ,25V 0.1 F ,50V 0.1 F ,25V 18 pF ,50V 18 pF ,50V 0.1 F ,25V 0.1 F ,25V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 22 F ,6.3V 0.1 F ,50V 150 pF ,50V 0.022 F ,50V 1000 pF ,50V 1000 pF ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 470 pF ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 1 F ,25V 1 F ,25V 0.015 F ,50V 1800 pF ,50V 12 pF ,50V 10 F ,25V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 4700 pF ,50V 680 pF ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 1000 pF ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 1 F ,25V 1 F ,25V 0.1 F ,50V

GX-BT7
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

[6] CAPACITORS
C 930 C 931 C 932 C 940 C 941 C 942 C 943 C 944 C 945 C 946 C 947 C 948 C 950 C 990 C 997 C 998 C 999 C A 57 C A 59 C A 600 C A 601 C A 602 C A 603 C A 60 4 C A 615 C A 616 C A 617 E 400 E 540 E 564 E 581 E 760 E 801 E 804 E 811 E 830 E 904 E 940 E 941 E 942 E 943 E A 600 E A 610 E A 616 V C K Y C Y 1E B 105K V C K Y C Y 1H B 104K V C K Y C Y 1E B 105K V C K Y T V 1H B 331K V C K Y C Y 1H B 102K V C K Y T V 1H B 331K V C K Y C Y 1H B 102K V C K Y T V 1H B 331K V C K Y C Y 1H B 102K V C K Y T V 1E B 684K V C K Y C Y 1H B 102K V C K Y C Y 1H B 102K V C K Y C Y 1H B 104K V C K Y T V 1H B 104K V C K Y T V 1H B 104K V C K Y T V 1H B 104K V C K Y T V 1H B 104K V C K Y C Z 1E F 104Z V C K Y C Z 1A B 225K V C K Y C Y 1H B 104K V C K Y C Y 1H B 104K V C K Y C Z 1E F 104Z V C K Y C Y 1H B 102K V C K Y C Z1H B 102K V C K Y C Y 1H B 104K V C K Y C Y 1H B 103K V C K Y C Y 1H B 103K V C E A Z A 1C W 226M V C E A Z A 1A W 107M V C E A Z A 1A W 107M V C E A Z A 1A W 107M R C -E Z D 476A F 1C V C E A Z A 1C W 108M V C E A Z A 1C W 477M V C E A Z A 1C W 477M V C E A Z A 1A W 107M V C E A Z A 1C W 477M V C E A Z A 1C W 477M V C E A Z A 1C W 477M V C E A Z A 1C W 477M V C E A Z A 1C W 477M R C -E Z D 107A F 1C V C E A Z A 1A W 227M V C E A Z A 1H W 475M AB AD AB AA AA AA AA AA AA AC AA AA AD AD AD AD AD AA AB AD AD AA AA AA AD AA AA AC AB AB AB AC AE AC AC AB AC AC AC AC AC AC AC AB 1 F ,25V 0.1 F ,50V 1 F ,25V 330 pF ,50V 1000 pF ,50V 330 pF ,50V 1000 pF ,50V 330 pF ,50V 1000 pF ,50V 0.68 F ,25V 1000 pF ,50V 1000 pF ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,50V 0.1 F ,25V 2.2 F ,10V 0.1 F ,50V 0.1 F ,50V 0.1 F ,25V 1000 pF ,50V 1000 pF ,50V 0.1 F ,50V 0.01 F ,50V 0.01 F ,50V 22 F ,16V 100 F ,10V 100 F ,10V 100 F ,10V 47 F ,16V 1000 F ,16V 470 F ,16V 470 F ,16V 100 F ,10V 470 F ,16V 470 F ,16V 470 F ,16V 470 F ,16V 470 F ,16V 100 F ,16V 220 F ,10V 4.7 F ,50V

[7] RESISTORS
F B 580 F B 581 F B 830 F B 840 JP 541 JP 588 JP 601 JP 602 JP 800 JP 891 JP 894 R 55 R 57 R 69 R 102 R 112 R 401 R 402 R 404 R 405 R 406 R 407 R 500 R 501 R 502 R 503 R 504 R 505 R 508 R 541 R 542 R 544 R 545 R 546 R 547 R 549 R 561 R 562 R 563 R 564 V R S -C Y 1JB 4R 7J V R S -C Y 1JB 4R 7J V R S -T V 2A B 000J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -T V 2A B 000J V R S -T V 2A B 000J V R S -C Z 1JB 472J V R S -C Z 1JB 472J V R S -C Y 1JB 102J V R S -C Y 1JB 472J V R S -C Y 1JB 472J V R S -C Y 1JB 221J V R S -C Y 1JB 221J V R S -C Y 1JB 101J V R S -C Y 1JB 101J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -C Y 1JB 000J V R S -C Y 1JB 223J V R S -C Y 1JB 223J V R S -C Y 1JB 683J V R S -C Y 1JB 683J V R S -C Y 1JB 153J V R S -C Y 1JB 472J V R S -C Y 1JB 103J V R S -C Y 1JB 912J V R S -C Y 1JB 912J V R S -C Y 1JB 912J V R S -C Y 1JB 912J V R S -C Y 1JB 102J V R S -C Y 1JB 103J V R S -C Y 1JB 103J V R S -C Y 1JB 103J V R S -C Y 1JB 103J AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 4.7 ohm ,1/16 W 4.7 ohm ,1/16 W 0 ohm , Jum per,1/10 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/10 0 ohm , Jum per,1/10 4.7 kohm ,1/16 W 4.7 kohm ,1/16 W 1 kohm ,1/16 W 4.7 kohm ,1/16 W 4.7 kohm ,1/16 W 220 ohm ,1/16 W 220 ohm ,1/16 W 100 ohm ,1/16 W 100 ohm ,1/16 W 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 22 kohm ,1/16 W 22 kohm ,1/16 W 68 kohm ,1/16 W 68 kohm ,1/16 W 15 kohm ,1/16 W 4.7 kohm ,1/16 W 10 kohm ,1/16 W 9.1 kohm ,1/16 W 9.1 kohm ,1/16 W 9.1 kohm ,1/16 W 9.1 kohm ,1/16 W 1 kohm ,1/16 W 10 kohm ,1/16 W 10 kohm ,1/16 W 10 kohm ,1/16 W 10 kohm ,1/16 W W W W W W W W W W

W W W W

GX-BT7
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

[7] RESISTORS
R 565 R 566 R 567 R 590 R 604 R 605 R 606 R 607 R 609 R 610 R 611 R 615 R 616 R 619 R 628 R 629 R 631 R 636 R 643 R 644 R 647 R 651 R 652 R 653 R 654 R 655 R 668 R 674 R 676 R 677 R 678 R 679 R 680 R 681 R 682 R 683 R 684 R 685 R 686 R 687 R 688 R 689 R 690 R 691 R 760 R 761 R 762 R 774 R 775 R 776 R 777 R 800 R 801 R 802 R 803 R 804 R 810 R 811 R 812 R 813 R 814 R 831 R 832 R 837 R 839 R 840 R 842 R 843 R 900 R 904 R 905 R 907 R 908 R 909 R 912 R 913 R 914 R 919 R 920 R 921 R 922 R 923 R 924 R 925 R 940 R 943 R 946 V R S -C Y 1JB 103J V R S -C Y 1JB 103J V R S -C Y 1JB 330J V R S -C Y 1JB 100J V R S -C Y 1JB 102J V R S -C Y 1JB 4R 7J V R S -C Y 1JB 4R 7J V R S -C Y 1JB 515J V R S -C Y 1JB 102J V R S -C Y 1JB 222J V R S -C Y 1JB 222J V R S -C Z 1JB 472J V R S -C Y 1JB 472J V R S -C Y 1JB 102J V R S -C Z 1JB 000J V R S -C Y 1JB 331J V R S -C Z 1JB 000J V R S -C Z 1JB 104J V R S -C Z 1JB 105J V R S -C Z 1JB 101J V R S -C Z 1JB 101J V R S -C Y 1JB 101J V R S -C Y 1JB 101J V R S -C Y 1JB 102J V R S -C Y 1JB 000J V R S -C Z 1JB 102J V R S -C Y 1JB 472J V R S -C Y 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Z 1JB 330J V R S -C Y 1JB 820J V R S -C Y 1JB 820J V R S -C Y 1JB 101J V R S -C Y 1JB 122J V R S -C Y 1JB 122J V R S -C Y 1JB 152J V R S -C Y 1JB 222J V R S -C Y 1JB 153J V R S -C Y 1JB 103J V R S -C Z 1JB 472J V R S -C Z 1JB 103J V R S -C Y 1JB 393J V R S -C Y 1JB R 33J V R S -C Y 1JB 000J V R S -C Y 1JB 202J V R S -C Y 1JB 182J V R S -C Y 1JF 122F V R S -C Y 1JB 103J V R S -C Y 1JB 471J V R S -C Y 1JB 102J V R S -C Y 1JB 103J V R S -C Y 1JB 000J V R S -C Y 1JB 473J V R S -C Y 1JB 822J V R S -T V 2A B 3R 3J V R S -T Q 2E F 6R 2J V R S -T Q 2E F 6R 2J V R S -T Q 2E F 6R 2J V R S -T Q 2E F 6R 2J V R S -C Z 1JB 222J V R S -C Y 1JB 220J V R S -C Y 1JB 103J V R S -C Y 1JB 472J V R S -C Z 1JB 000J V R S -C Z 1JB 000J V R S -C Z 1JB 000J V R S -C Z 1JB 562J V R S -C Y 1JB 332J V R S -C Z 1JB 101J V R S -C Z 1JB 101J V R S -T V 2A B 200J V R S -T V 2A B 200J V R S -T V 2A B 200J AA AA AA AA AA AA AA AA AA AA AA AB AA AA AB AA AB AA AB AB AB AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AB AB AB AB AA AB AB AA AA AA 10 kohm ,1/16 W 10 kohm ,1/16 W 33 ohm ,1/16 W 10 ohm ,1/16 W 1 kohm ,1/16 W 4.7 ohm ,1/16 W 4.7 ohm ,1/16 W 5.1 M ohm ,1/16 W 1 kohm ,1/16 W 2.2 kohm ,1/16 W 2.2 kohm ,1/16 W 4.7 kohm ,1/16 W 4.7 kohm ,1/16 W 1 kohm ,1/16 W 0 ohm , Jum per,1/16 330 ohm ,1/16 W 0 ohm , Jum per,1/16 100 kohm ,1/16 W 1 M ohm ,1/16 W 100 ohm ,1/16 W 100 ohm ,1/16 W 100 ohm ,1/16 W 100 ohm ,1/16 W 1 kohm ,1/16 W 0 ohm , Jum per,1/16 1 kohm ,1/16 W 4.7 kohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 82 ohm ,1/16 W 82 ohm ,1/16 W 100 ohm ,1/16 W 1.2 kohm ,1/16 W 1.2 kohm ,1/16 W 1.5 kohm ,1/16 W 2.2 kohm ,1/16 W 15 kohm ,1/16 W 10 kohm ,1/16 W 4.7 kohm ,1/16 W 10 kohm ,1/16 W 39 kohm ,1/16 W R .3 ohm ,1/16 W 0 ohm , Jum per,1/16 2 kohm ,1/16 W 1.8 kohm ,1/16 W 1.2 kohm ,1/16 W 10 kohm ,1/16 W 470 ohm ,1/16 W 1 kohm ,1/16 W 10 kohm ,1/16 W 0 ohm , Jum per,1/16 47 kohm ,1/16 W 8.2 kohm ,1/16 W 3.3 ohm ,1/10 W 6.2 ohm ,1/4 W 6.2 ohm ,1/4 W 6.2 ohm ,1/4 W 6.2 ohm ,1/4 W 2.2 kohm ,1/16 W 22 ohm ,1/16 W 10 kohm ,1/16 W 4.7 kohm ,1/16 W 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 0 ohm , Jum per,1/16 5.6 kohm ,1/16 W 3.3 kohm ,1/16 W 100 ohm ,1/16 W 100 ohm ,1/16 W 20 ohm ,1/10 W 20 ohm ,1/10 W 20 ohm ,1/10 W

W W

W W W

GX-BT7
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

[7] RESISTORS
R 948 R 949 R 950 R 951 R 952 R 953 R 954 R 955 R 956 R 957 R 958 R 959 R 960 R 963 R 964 R 965 R 966 R A 44 R A 46 R A 47 R A 48 R A 600 R A 601 R A 602 R A 603 R A 604 R A 605 R A 606 R A 610 R A 611 R A 612 R A 613 R A 614 R A 615 R A 616 R D 914 R U 549 R U 637 R U 638 V R S -C Y 1JB 332J V R S -C Y 1JB 332J V R S -C Y 1JB 332J V R S -C Y 1JB 8R 2J V R S -C Z 1JB 101J V R S -C Y 1JB 102J V R S -C Y 1JB 8R 2J V R S -C Y 1JB 102J V R S -C Y 1JB 332J V R S -C Y 1JB 332J V R S -C Y 1JB 3R 3J V R S -C Y 1JB 000J V R S -C Y 1JB 3R 3J V R S -T V 2A B 000J V R S -T V 2A B 000J V R S -C Y 1JB 102J V R S -C Z 1JB 101J V R S -C Y 1JB 153J V R S -C Y 1JB 393D V R S -C Y 1JB 243D V R S -C Z 1JB 104J V R S -C Z 1JF 113F V R S -C Y 1JB 330J V R S -C Y 1JB 330J V R S -C Z 1JB 330J V R S -C Y 1JB 330J V R S -C Z 1JB 000J V R S -C Y 1JB 100J V R S -C Y 1JB 102J V R S -C Y 1JB 4R 7J V R S -C Y 1JB 2R 2J V R S -C Y 1JB 102J V R S -C Y 1JB 153J V R S -C Y 1JB 681J V R S -C Y 1JB 103J V R S -C Z 1JB 000J V R S -C Y 1JB 103J V R S -C Y 1JB 153J V R S -C Z 1JB 153J AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AB AA AA AA 3.3 kohm ,1/16 W 3.3 kohm ,1/16 W 3.3 kohm ,1/16 W 8.2 ohm ,1/16 W 100 ohm ,1/16 W 1 kohm ,1/16 W 8.2 ohm ,1/16 W 1 kohm ,1/16 W 3.3 kohm ,1/16 W 3.3 kohm ,1/16 W 3.3 ohm ,1/16 W 0 ohm , Jum per,1/16 3.3 ohm ,1/16 W 0 ohm , Jum per,1/10 0 ohm , Jum per,1/10 1 kohm ,1/16 W 100 ohm ,1/16 W 15 kohm ,1/16 W 39 kohm ,1/16 W 24 kohm ,1/16 W 100 kohm ,1/16 W 11 kohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 33 ohm ,1/16 W 0 ohm , Jum per,1/16 10 ohm ,1/16 W 1 kohm ,1/16 W 4.7 ohm ,1/16 W 2.2 ohm ,1/16 W 1 kohm ,1/16 W 15 kohm ,1/16 W 680 ohm ,1/16 W 10 kohm ,1/16 W 0 ohm , Jum per,1/16 10 kohm ,1/16 W 15 kohm ,1/16 W 15 kohm ,1/16 W

W W W

[8] OTHER CIRCUITRY PARTS

B I600 B I800 C N P 107 C N P 162 C N P 601 C N P 602 C N P 604 C N P 605 C N P 606 C N P 607 C N P 760 C N P 770 C N P 901 C N P 903 JK 500 JK 580 LUG100 SW161 SW162 SW770 SW776 SW777 SW778 SW779 SW780 F F C 607 F F C 601 F F C 602 CNS107 CNS901 FPC[L] FPC[R] RM760 Q C N W N C 278A W P Z Q C N W N C 279A W P Z Q C N C M 202B A W Z Z Q C N C W Y H 05A W Z Z Q C N C W Y H 06A W Z Z Q C N C W Y H 05A W Z Z Q C N C W Y G 07A W Z Z Q C N C W Y G 09A W Z Z Q C N C W Y G 09A W Z Z Q C N C W Y H 07A W Z Z Q C N C W Y H 06A W Z Z Q C N C M 202C A W Z Z Q C N C M 203D A W Z Z Q C N C M 203B A W Z Z Q JA K M A 013A W Z Z Q S O C Z A 039A W Z Z Q C N W N C 337A W P Z Q S W -P 9003A W Z Z Q S W -P 9003A W Z Z 92LS W IC H T 1663T 92LS W IC H T 1663T 92LS W IC H T 1663T 92LS W IC H T 1663T 92LS W IC H T 1663T 92LS W IC H T 1663T AE AE AB AB AC AB AC AC AC AC AC AB AB AB AF AE AD AD AD AC AC AC AC AC AC AE AD AD AD AQ AS AS AE C onnector W ire A ssy, 4P -3P C onnector W ire A ssy, 2P [M ain P W B to S M P S P W B ] C onnector, 2P [S ide E ntry] F F C C onnector, 5P F F C C onnector, 6P F F C C onnector, 5P F F C C onnector, 7P F F C C onnector, 9P [LE D L-C h] F F C C onnector, 9P [LE D R -C h] F F C C onnector, 7P F F C C onnector, 6P S ide E ntry S ock et, 3P S T M C onnector 4P C onnector, 2P [S ide E ntry] Jack , H eadphone Jack , U S B Lug W ire M ode S w itch M ode S w itch S w itch [O N / S T A N D -B Y ] S w itch [B LU E T O O T H P A IR IN G ] S w itch [F U N C T IO N ] S w itch [X-B A S S ] S w itch [V O LU M E U P ] S w itch [V O LU M E D O W N ] F F C C able, 7P F F C C able, 6P F F C C able, 5P Connector Wire Assy, 2P [To Door Motor] Connector Wire Assy, 4P+2P [for Speaker and Subwoofer] FPC Connector Assy [Blue LED Module] FPC Connector Assy [Blue LED Module] Remote Sensor

RUITZA119AWZZ RUITZA119AWZZ VHL8631MH65-1

GX-BT7
-MEMO-

214 239 208 221 602 x 2 217 203 225 225 606 x 3 202 226 608 x 4 228 SP1 609 x 3 209 PWB-B SP2 606 x 3 609 x 4 228 SP4 234 211 236 237 217 606x2 602 x 2 206 214 608 x 4 224 601 x 4 606 - 1 x 4 220 224 605 x 3 226 PWB-A2 230 601 x 4 606 - 1 x 4 606 605 x 3 230

606x2

201

[9] CABINET PARTS

206

SP3

7
229 606 x 2 223 216 222 602 x 2 606 x 4 219 218 606 x 2 229 605 212 603 x 2 223 605 607 605 207 LED 233

PWB-A1

LED 238

233

213

215

207

607 605

204

605

606 x 2

PWB-A3

210

604

PWB-A4

605 x 2

604

235

PWB-A5

205

GX-BT7

GX-BT7
NO. PARTS CODE PRICE NEW PART RANK MARK RANK DESCRIPTION

[9] CABINET PARTS / CD MECHANISM PARTS

201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 SP 1, 2 SP 3, 4 SP 3, 4 601 602 603 604 605 606 606-1 607 608 609 GCAB-A167AWSA GCAB-A169AWSA GCAB-A170AWSA GCAB-A182AWSA GWAKPA076AWSA GWAKPA077AW01 HDECQA721AWSA JKNBZA383AWSB LANGKA290AWFW LBND-1011AWZZ LCHSMA151AWFW LHLDZA360AWZZ LHLDZA370AWZZ LHLDZA380AWZZ LHLDZA381AWZZ LHLDZA384AWZZ MSPRCA020AWFJ NGERH0132AWZZ NGERH0163AWZZ NGERRA009AWZZ NGERRA010AWZZ NGERWA011AWZZ PCUSGA247AWZZ PCUSSA292AWZZ PCUSSA295AWZZ PCUSSA296AWZZ PCUSSA297AWZZ PFLT-A209AWZZ PFLT-A211AWZZ PFLT-A216AWZZ PFLT-A219AWZZ PFLT-A223AWZZ PSHEZA339AWSA PSHEZA345AWZZ PSPAZA034AWZZ PSPAZA045AWZZ PSPAZA046AWZZ QACCDA017AWZZ TSPC-B900AWZZ RSP-ZA412AWZZ RSP-ZA418AWZZ RSP-ZA419AWZZ LX-JZA010AWF7 LX-WZA046AWF7 XBPY726P04000 XEBY726P06000 XEBY726P08000 XEBY730P10000 XEBY730P10000 XEBY826P08000 XEBY830P10000 XJBY730P06000 AQ AQ AQ AV AG AG AE AA AH AK AK B ack Top C abinet S peak er C abinet, F ront (R ight) S peak er C abinet, F ront (Left) Bottom C abinet C entre F ram e F ront F ram e A ss'y P anel, LE D B utton, O peration A ngle N ylon B and C hassis, M ain H older, LE D (R ight) H older, LE D (Left) H older, Frame H older, Mechanism A ss'y H older, G ear Spring Door D rive G ear A D rive G ear B R ack G ear (R ight) R ack G ear (Left) W heel G ear C ushion, F oot C ushion, S peak er C ushion, S eal (Right) C ushion, S eal (Left) C ushion, Back Cab Felt, Speaker Cabinet Felt, Mechanism Holder Felt, Button Felt, Bottom Cab Felt, Bottom S heet, LE D D iffusion S heet, S M P S S heet, LE D S heet, H eat T ransfer A S heet, H eat T ransfer B A C P ow er S upply C ord Label, S pecification S peak er Subwoofer [use for S/No. 40200001 - 40201000 only] S ubw oofer [use for S/No. 40301001 onwards] S crew , S pecial [use for S/No. 40301001 onwards] S crew , S pecial S crew , M 2.6 X4m m S crew , M 2.6 X6m m S crew , M 2.6 X8m m S crew , M 3 X10m m Screw, M3 X10m m [use for S/No. 40200001 - 40301000 only] S crew , M 2.6 X8m m S crew , M 3 X10m m S crew , M 3 X6m m

AC AD AE AD AD AB AB AB AB AB AB AE AE AB AB AB AM AD AB AA AA AA AA AA AB AB AA

GX-BT7

[10] ACCESSORIES / PACKING PARTS

1 2 3 4 5 5-1 5-2 6 7 8 9 10 GCASP8945AW01 GiTAUA028AW01 PSHEZA377AW01 PSHEZA378AW01 RRMCGA342AW02 RRMCGA342AWSA TLABZC562AWZZ TCAUZA324AWZZ TiNSKA092AWZZ TiNSZB591AWZZ TLABZA149AWSA TLABZC578AWZZ AU AR NFC Tag Ass'y Stand for iPad Ass'y Velcro Tape (Loop) Ass'y Velcro Tape (Hook) Ass'y Remote Control Ass'y Remote Control [Not Replacement Item] (Sold together with TLABZC562AWZZ, Refer item No. 5 (RRMCGA342AW02)) Label, Battery Caution [Not Replacement Item] (Sold together with RRMCGA342AWSA, Refer item No. 5 (RRMCGA342AW02)) Sheet, Memo Operation Manual (French) Operation Manual (English, Spanish) Label, Energy Star Label, Caution

--AB AA

[11] P.W.B. ASSEMBLY

P W B -A
!

92LP W B 8945M A N S R U iT Z A 115A W Z Z

BT BA

S .X C ategory X C ategory

Main (A1) / Key (A2) / LED Driver (A3) / Remote Sensor (A4) / Switch (A5) SMPS

P W B -B

GX-BT7

PACKING METHOD (FOR U.S.A. ONLY)

Packing Add, Bottom * SPAKAA513AWZZ

Label, Energy Star

Miramat Bag * SSAKHA274AWZZ

Polyethylene Bag, NFC Tag * SSAKHA241AWZZ NFC Tag Assy Stand for iPad Ass'y

Packing Add, Bottom * SPAKAA514AWZZ Velcro Tape (Loop) Assy x 3 Velcro Tape (Hook) Assy x 2 Polyethylene Bag, Accessories * SSAKAA011AWZZ Remote Control Assy Operation Manual x 2 Sheet, Memo

Packing Case * SPAKCB209AWZZ

Front of Packing Case

* Not Replacement Item

10

GX-BT7

COPYRIGHT

2014 BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

SHARP CORPORATION S&O Electronics (Malaysia) Sdn. Bhd. Sungai Petani, Kedah, Malaysia

Printed in Malaysia

A1401-1MX RR M SC SL