Scribd
Upload
226 views5 pages

CD Mechanism Type CDM53F-K2BD38

The document provides installation instructions for removing and replacing various components of an optical disc drive, including: 1. Removing screws to detach the CD mechanism deck, tape mechanism deck, CD base unit, fitting base assembly, tray, chassis section, stocker section, and slider. 2. Adjusting gears and installing the slider selection, stocker section, and chassis section in the correct positions. 3. Hooking the tray portion to the slider selection and inserting chassis sections into slider portions.

Uploaded by

AlejandroVCMX
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
226 views5 pages

CD Mechanism Type CDM53F-K2BD38

The document provides installation instructions for removing and replacing various components of an optical disc drive, including: 1. Removing screws to detach the CD mechanism deck, tape mechanism deck, CD base unit, fitting base assembly, tray, chassis section, stocker section, and slider. 2. Adjusting gears and installing the slider selection, stocker section, and chassis section in the correct positions. 3. Hooking the tray portion to the slider selection and inserting chassis sections into slider portions.

Uploaded by

AlejandroVCMX
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

2-7.

CD MECHANISM DECK (CDM53F-K2BD38)


4 Four screws (BVTP 3 8) 5 Remove the CD mechanism deck section. 3 Chassis

2 Two screws (BVTP 3 8)

1 Three screws (BVTP 3 8)

2-8. TAPE MECHANISM DECK (TCM-230AWR12)


3 Remove the tape mechanism deck section.

1 Two screws (BVTP 3 8)

2 Two screws (BVTP 3 8)

11

2-9. CD BASE UNIT (BU-K2BD38)

5 CD base unit (BU-K2BD38)

4 Compression spring (black)

2 Compression spring (sliver)

3 Two screws (PTPWH M2.6)

1 Two screws (PTPWH M2.6)

2-10.

FITTING BASE (GUIDE) ASSY, BRACKET (CHASSIS) AND MAGNET ASSY


8 Four screws (BVTP M2.6) 6 Bracket (chassis)

2 Four screws (BVTP M2.6)

4 Screw (BVTP M2.6)

7 Connector (CN710)

9 Magnet assy 5 Screw (BVTP M2.6)

3 Fitting base (guide) assy 1 Two connectors (CN709, 715)

12

2-11.

TRAY (SUB)

1 Rotating the pulley (LD), shift the slider (selection) in the arrow A direction. 2 Rotating the pulley (mode) in the arrow direction, adjust the tray (sub) to be removed. 3 Rotating the pulley (LD), shift the slider (selection) in the arrow B direction. 4 Rotating the pulley (mode) in the arrow direction, remove the tray (sub) to be removed.
Slider (selection)

Pully (LD)

Stocker section

A B

Pully (mode)

Tray (sub)

2-12.

CHASSIS (MOLD B) SECTION, STOCKER SECTION AND SLIDER (SELECTION)

Note: In mounting the parts, refer to page 14 and 15.

6 Two screws (PTPWH M2.6) 5 Stocker section

7 Slider (selection) 8 Washer

Pully (LD)

9 Compression spring

1 Three screws (BVTP M2.6)

4 Two step screws

2 Chassis (mold B) section Note: Rotating the pully (LD), shift the slider (selection) to the left.

4 Two step screws

3 Gear (eject)

13

2-13.

GEARS INSTALLATION
3 Gear (gear B) Portion A

Adjust the gear (gear B) with the portion A as shown.

1 Slide the slider (u/d) fully in the arrow direction.

2 Gear (U/D slider)

4 Gear (gear A)

Slider (U/D) gear

Gear (gear B)

Linearly

Adjust the gear so that it meshes with the bottom tooth of slider (U/D) gear, as shown.

Adjust so as to be aligned with gear B linearly, as shown.

2-14.

SLIDER (SELECTION) INSTALLATION


6 Two screws (PTPWH M2.6) 2 Gear (chuking)

Rotary encoder

5 Washer 4 Compression spring 7 Insert the slider (selection) into the portion A.

Align with the slot of rotary encoder.

Portion A

3 Convex portion of slider (selection) Gear (chuking) 1 Rotary encoder

Insert a convex portion into a groove of gear (chuking). Align marking

14

2-15.

STOCKER SECTION INSTALLATION


2 Portion A of tray (sub) 1 Stocker section

Hook the portion A of tray (sub) to the slider (selection).

Portion A of tray (sub)


3 Two step screws

Sticking of slider (selection)

3 Two step screws

2-16.

CHASSIS (MOLD B) SECTION INSTALLATION

3 Three screws (BVTP M2.6)

2 Insert the gear (eject0 under the gear (LD deceleration).

Portion A

1 Insert the portion A of chassis (mold B) section into the portion B of slider (selection).

Gear (LD deceleration)

Portion B of slider (selection)

15

You might also like