Mostuf Catalog
Mostuf Catalog
MOSTUF
Filament wound
Composite
Bearings
Maintenance-free
11-88, Songrim-Dong, Dong-Gu, Incheon, KOREA 401-076 Tel : 82-32-761-2323 / Fax : 82-32-761-2322
Contents
1. Introduction .......................................... 4 p
2. Features & Benefits ............................. 4 p
3. Material Structure ................................ 5 p
4. Applications ......................................... 6 p
MOSTUF T
- Standard type
- Specially woven (PTFE + synthetic fiber)
bearing layer
- Ideal for low speed/high load application
MOSTUF P
- Standard type
- Filled PTFE bearing layer
- Very good friction and wear properties
MOSTUF S
- Machinable bearing layer
- Filament wound synthetic fiber with
graphite additions
- Suitable for large size composite bush
MOSTUF F
- Lower frictional coefficient and wear rate
than MOSTUF T
- Filament wound twisted (PTFE+synthetic
fiber) layer with graphite additions
2/3
SOLTRI
Introduction
The demands for environmentally friendly sliding bearing which is maintenance-free
even under harsh conditions and free from contaminations caused by grease or oil
are increasing gradually.
MOSTUF composite bearings are self-lubricating sliding materials with high loadcarrying capacity to be applied under slow speed rotating, oscillating and
reciprocating movements.
MOSTUF composite bearings have excellent sliding performance when they are
applied to some place where lubrication is not possible or not allowed since they
maintain good wear resistance and low coefficient of friction.
Material Structure
MOSTUF composite bearings have two layers that
are manufactured by a filament winding process.
And various bearing layers are available as per
applied conditions
Bearing layer of MOSTUF T is composed of a
proprietary designed woven structure of PTFE and
high strength synthetic fibers with specially
formulated solid lubricant additions.
Backing Layer
MOSTUF T
Bearing Layer
MOSTUF P
MOSTUF S
Backing Layer
MOSTUF F
Bearing Layer
Fig.1 - Microstructure of MOSTUF composite bearings
4/5
Bearing Performance
Applications
Mechanical Properties
Units
Values
MPa
430
MPa
240
MPa
550
Hardness
HRM
95
Density
g/cm3
2.0
underwater circumstance.
Valves and Actuators
Hydraulic & Pneumatic
cylinders, Linear slide,
Butterfly valves
Construction Equipment
Excavators, Cranes,
Street sweepers
Recreation Applications
Ski lifters, Snow mobiles,
Fitness equipment, Golf carts
Agricultural Equipment
Tractors, Combines,
Seed-treatment units
Marine Equipment
Underwater robots,
Stern drive on speed motors
Fig.3 - Permanent set and deflection of MOSTUF T bearing
6/7
Bearing Properties
Bearing Wear
Units
MOSTUF T
MOSTUF P
static
MPa
240
140
dynamic
MPa
140
35
m/sec
0.2
2.5
MPa x m/sec
1.8
2.0
0.03~0.12
0.03~0.08
160
180
-100
-100
Maximum load
Maximum sliding speed
Maximum PV value
Frictional coefficient(dry)
Bearing wear occurs due to many kinds of factors. Fig.6 shows the test results under
bearing pressure of 60 MPa at room temperature. There shows rapid wear during
initial thousands of cycles. During this period, there happens transfer of PTFE on the
surface of shaft and redistribution of fiber on the sliding direction, resulting into
smooth bearing surfaces. After some initial wear, wear rate shows steady progress.
Direct wear stays under 0.12mm after 256,000 cycles.
Coefficient of Friction
The dynamic coefficient of friction for MOSTUF composite bearing is between 0.03 ~ 0.12,
depending upon load, type of movement, sliding speed, operating temperature, micro finish
of mating surface. Fig.5 shows the change of dynamic coefficient of friction under oscillating
load. At the beginning of test, coefficient of friction is being kept up on steady-state
conditions
Fig.7 shows the shaft and bearing after finishing all test cycles.
Fig.8 shows contact area which was highly polished and journal
contact surface had a significant amount of wear debris(lubricant
film) adhering to the contact face. Fig.9 shows close up view of
bushing center of contact surface. There did not appear to be any
damage to the bearing surface other than minor polishing.
Fig.8 - Close up view of
MOSTUF T journal
contact surface.
Design Considerations
Thermal Properties
Operating temperature of MOSTUF composite bearing is between -100 ~ +160C. And coefficient of
thermal expansion is similar to the coefficient of thermal expansion of steel. So the bearing can exhibit its
performance without separating from housing even though exposed extreme temperature change.
MOSTUF T
Coefficient of thermal
expansion(25~150 )
Unit
MOSTUF
Bearing
Steel
Aluminum
/m
13 10-6
11 10-6
24 10-6
Composite Bearing
Standard type
Specially woven (PTFE+synthetic fiber)
bearing layer
Ideal for high load, low speed applications
Table 3. - Coefficient of thermal expansion for MOSTUF bearing composites, steel, and aluminum
MOSTUF P
Chemical Properties
MOSTUF composite bearings have resisting power to various kinds of chemical substances. Also they have
dimensional stability even after exposed into sea water or fresh-water for a long time.
Alcohols
Methanol
Ethyl alcohol
Allyl alcohol
Butyl alcohol
Propyl alcohol
Isopropanol
Hydroxy aceton
Solvents
Aceton
Toluene
Methyl ethyl keton
Trichloroethane
Benzene
Acids(10%)
Hydrochloric acid
Boric acid
Acetic acid
Sulphuric acids
Nitric acids
Carbonic acids
Hydrofluoric acid
Oils
Gear oil
Motor oil
Hydraulic oil
Linseed oil
Fuels
Kerosene
Jet fuel
Diesel
Petroleum
Sodium hydroxid
Salts
Sodium acetate
Sodium carbonate
Ammonium nitrate
Ammonium chloride
Magnesium sulphate
Gases
Butane
Ozone
Nitrogen
Natural gas
Acetylene
Hydrogen
Fluorine
Chlorine gas
MOSTUF S
Composite Bearing
MOSTUF F
Composite Bearing
Alkalies(10%)
Sodium hydroxide
Calcium hydroxide
Ammonium hydroxide
Magnesium hydroxide
Others
Freon
Formaldehyde
Sodium nitrate
Ethylene glycol
Ammonia
100% water
resistant
Composite Bearing
Bearing Proportions
Optimum performance for MOSTUF composite bearing can be
achieved by specifying a length to inside diameter ratio(L/d) ranging
from 0.5 to 2.0. When the values of L/d are between above ranges,
wear debris can escape from the bearing easily and the bearing
became less sensitive to shaft deflection and misalignment.
non resistant
L/d values of more than 2.0 are not recommended but where long
bearing has been indicated it is advisable to consider using two
bearings with a small gap between them. If the value of the L/d is less
than 0.5, there would a possibility for some cracking on the edge of
bearing due to stress concentrations.
10 / 11
Bearing Pressure
Bearing pressure is defined as maximum load operated on the projected bearing
area. Load capacity will be declined as temperature rises and it will be increased as
temperature goes down. And load capacity will be affected by the type of operated
load. Generally, load capacity of MOSTUF composite bearing is 140MPa when
uniform load is operated on the bearing and 100MPa under dynamic or oscillating
load that cause fatigue stress.
Bearing Speed
Allowable maximum speed for MOSTUF T composite bearing is 0.2m/s. It exhibits
excellent performance when it operates at a slow speed under high load. In case
bearing speed is very high, too much of frictional heat would be occurred and
allowable bearing pressure would be decreased accordingly.
Bearing Pressure
P(MPa) =
d
Bearing Speed
Rotation
V(m/s)=5.24 10-5dN
Oscillation
V(m/s)=5.82 10-7dc
SOLUTION OF COMPOSITE BEARING
where
W = radial load(N)
L = bearing length(mm)
c = cycling rate(cycles/min)
d = bearing ID(mm),
N = rotation speed(revs/min),
= half turning angle(degree)
MOSTUF
Bearing PV
The value of PV can be calculated by multiplying bearing pressure by bearing
velocity and it indicates surface running speeds and loads under which a bearing
can safely operate. Allowable PV limit for MOSTUF T composite bearing is 1.8MPa.
m/s. Frictional heat and wear rate would be increased rapidly in case of over PV limit.
Installation
M O S T UF M e tr i c S i z e
Bearing Sizes
ID
+0.070
+0.040
15, 20, 25
12h7
0
- 0.018
17H7
+0.018
0
0.022~0.070
0.020~0.136
15
+0.145
+0.095
20
+0.075
+0.045
15, 20, 25
15h7
0
- 0.018
20H7
+0.021
0
0.024~0.075
0.020~0.139
16
+0.145
+0.095
21
+0.075
+0.045
15, 20, 25
16h7
0
- 0.018
21H7
+0.021
0
0.024~0.075
0.020~0.139
18
+0.195
+0.115
23
+0.095
+0.045
15, 20, 25
18h7
0
- 0.018
23H7
+0.021
0
0.024~0.095
0.020~0.189
20
+0.196
+0.116
25
+0.096
+0.046
15, 20, 30
20h7
0
- 0.021
25H7
+0.021
0
0.025~0.096
0.020~0.192
22
+0.196
+0.116
27
+0.096
+0.046
15, 20, 30
22h7
0
- 0.021
27H7
+0.021
0
0.025~0.096
0.020~0.192
25
+0.196
+0.116
30
+0.096
+0.046
20, 30, 40
25h7
0
- 0.021
30H7
+0.021
0
0.025~0.096
0.020~0.192
28
+0.200
+0.120
34
+0.100
+0.050
20, 30, 40
28h7
0
- 0.021
34H7
+0.025
0
0.025~0.100
0.020~0.196
30
+0.200
+0.120
36
+0.100
+0.050
20, 30, 40
30h7
0
- 0.021
36H7
+0.025
0
0.025~0.100
0.020~0.196
35
+0.200
+0.120
41
+0.100
+0.050
30, 40, 50
35h7
0
- 0.025
41H7
+0.025
0
0.025~0.100
0.020~0.200
40
+0.200
+0.120
48
+0.100
+0.050
30, 40, 60
40h7
0
- 0.025
48H7
+0.025
0
0.025~0.100
0.020~0.200
45
+0.230
+0.130
53
+0.105
+0.055
30, 40, 60
45h7
0
- 0.025
53H7
+0.030
0
0.025~0.105
0.025~0.230
50
+0.230
+0.130
58
+0.105
+0.055
40, 50, 60
50h7
0
- 0.025
58H7
+0.030
0
0.025~0.105
0.025~0.230
55
+0.245
+0.145
63
+0.120
+0.070
40, 55, 70
55h7
0
- 0.030
63H7
+0.030
0
0.040~0.120
0.025~0.235
60
+0.245
+0.145
70
+0.120
+0.070
40, 60, 80
60h7
0
- 0.030
70H7
+0.030
0
0.040~0.120
0.025~0.235
65
+0.245
+0.145
75
+0.120
+0.070
50, 60, 80
65h7
0
- 0.030
75H7
+0.030
0
0.040~0.120
0.025~0.235
70
+0.245
+0.145
80
+0.120
+0.070
50, 70, 90
70h7
0
- 0.030
80H7
+0.030
0
0.040~0.120
0.025~0.235
75
+0.275
+0.175
85
+0.125
+0.075
50, 70, 90
75h7
0
- 0.030
85H7
+0.035
0
0.040~0.125
0.050~0.265
80
+0.275
+0.175
90
+0.125
+0.075
80h7
0
- 0.030
90H7
+0.035
0
0.040~0.125
0.050~0.265
85
+0.275
+0.175
95
+0.125
+0.075
85h7
0
- 0.035
95H7
+0.035
0
0.040~0.125
0.050~0.270
90
+0.275
+0.175
105
+0.125
+0.075
90h7
0
- 0.035
105H7
+0.035
0
0.050~0.135
0.050~0.270
XX
95
+0.310
+0.185
110
+0.135
+0.085
95h7
0
- 0.035
110H7
+0.035
0
0.050~0.135
0.050~0.295
100
+0.310
+0.185
115
+0.135
+0.085
100h7
0
- 0.035
115H7
+0.035
0
0.050~0.135
0.050~0.295
110
+0.315
+0.190
125
+0.135
+0.085
110h7
0
- 0.035
125H7
+0.040
0
0.050~0.140
0.050~0.300
120
+0.340
+0.215
135
+0.165
+0.090
120h7
0
- 0.035
135H7
+0.040
0
0.050~0.165
0.050~0.325
130
+0.340
+0.215
145
+0.165
+0.090
130h7
0
- 0.040
145H7
+0.040
0
0.050~0.165
0.050~0.330
140
+0.340
+0.215
155
+0.165
+0.090
140h7
0
- 0.040
155H7
+0.040
0
0.050~0.165
0.050~0.330
150
+0.340
+0.215
165
+0.165
+0.090
150h7
0
- 0.040
165H7
+0.040
0
0.050~0.165
0.050~0.330
MM
OD80
50mm Long)
XX
OD
XX
2. Inch Size
INCH SIZE
BM
Bearing Layer
T:
P:
S:
F:
Bearing Layer
T, P, S, F
X
OD 2.25
1 Long)
ID
in 1/16
OD
in 1/16
L
in 1/8
XX
XX
XX
Housing
Running
Clearance
17
ID
Shaft
Interference
Fit
+0.140
+0.090
Size Table
Bearing Layer
T, P, S, F
X
Recommended Sizes
12
METRIC SIZE
OD
Standard
Length
14 / 15
M O ST U F T B e a r i n g s / St a n d a r d W a l l - 1 /8
Bearing Nominal Size
Part No.
ID OD
Standard
Length
BMT 0812
1/2 3/4
1/2, 3/4,1
BMT 1014
5/8 7/8
1/2, 3/4,1
BMT 1216
3/4 1
1/2, 3/4,1
BMT 1418
7/8 1-1/8
BMT 1620
1 1-1/4
3/4, 1, 1-1/2
BMT 1822
1-1/8 1-3/8
3/4, 1, 1-1/2
BMT 2024
1-1/4 1-1/2
1, 1-1/4, 1-1/2
BMT 2226
1-3/8 1-5/8
1, 1-1/4, 1-1/2
BMT 2428
1-1/2 1-3/4
1-1/4, 1-1/2, 2
BMT 2630
1-5/8 1-7/8
1-1/4, 1-1/2, 2
BMT 2832
1-3/4 2
1-1/4, 1-1/2, 2
BMT 3236
2 2-1/4
1-1/2, 2, 3
BMT 3640
2-1/4 2-1/2
1-1/2, 2, 3
BMT 3842
2-3/8 2-5/8
1-1/2, 2, 3
BMT 4044
2-1/2 2-3/4
2, 2-1/2, 3
BMT 4246
2-5/8 2-7/8
2, 2-1/2, 3
BMT 4448
2-3/4 3
2, 2-1/2, 3
BMT 4852
3 3-1/4
2, 2-1/2, 3
BMT 5256
3-1/4 3-1/2
2, 2-1/2, 3
BMT 5660
3-1/2 3-3/4
2, 4
BMT 6064
3-3/4 4
2, 4
BMT 6468
4 4-1/4
2, 4
BMT 6872
4-1/4 4-1/2
2, 4
BMT 7276
4-1/2 4-3/4
2, 4
BMT 7680
4-3/4 5
2, 4
BMT 8084
5 5-1/4
2, 4
M O S T U F T B e a r i n g s / H ea v y W a l l - 1 / 4
Recommended Size
ID
Interference Fit
OD
Housing
Shaft
0.5040
0.5020
0.6290
0.6270
0.7555
0.7525
0.8805
0.8775
1.0055
1.0025
1.1335
1.1305
1.2555
1.2525
1.3830
1.3790
1.5080
1.5040
1.6330
1.6290
1.7580
1.7540
2.0080
2.0040
2.2580
2.2540
2.3850
2.3810
2.5100
2.5060
2.6370
2.6330
2.7620
2.7580
3.0140
3.0100
3.2640
3.2600
3.5140
3.5100
3.7640
3.7600
4.0140
4.0100
4.2640
4.2600
4.5140
4.5100
4.7640
4.7600
0.7515
0.7505
0.8765
0.8755
1.0025
1.0005
1.1275
1.1255
1.2525
1.2505
1.3785
1.3765
1.5025
1.5005
1.6285
1.6265
1.7535
1.7515
1.8785
1.8765
2.0035
2.0015
2.2535
2.2515
2.5040
2.5020
2.6290
2.6270
2.7540
2.7520
2.8790
2.8770
3.0040
3.0020
3.2540
3.2520
3.5040
3.5020
3.7540
3.7520
4.0040
4.0020
4.2540
4.2520
4.5040
4.5020
4.7540
4.7520
5.0040
5.0020
0.7500
0.7495
0.8750
0.8745
1.0000
0.9995
1.1250
1.1245
1.2500
1.2495
1.3750
1.3745
1.5000
1.4995
1.6250
1.6245
1.7500
1.7495
1.8750
1.8745
2.0000
1.9995
2.2505
2.2495
2.5005
2.5020
2.6255
2.6245
2.7505
2.7495
2.8755
2.8745
3.0005
2.9990
3.2505
3.2490
3.5010
3.4990
3.7510
3.7490
4.0010
3.9990
4.2510
4.2490
4.5010
4.4990
4.7510
4.7490
5.0010
4.9990
0.4990
0.4985
0.6240
0.6235
0.7490
0.7485
0.8745
0.8740
0.9990
0.9985
1.1250
1.1245
1.2490
1.2485
1.3745
1.3735
1.4995
1.4990
1.6245
1.6240
1.7495
1.7490
1.9995
1.9985
2.2490
2.2485
2.3750
2.3740
2.4995
2.4985
2.6245
2.6235
2.7495
2.7485
2.9995
2.9985
3.2495
3.2485
3.4995
3.4985
3.7495
3.7485
3.9995
3.9985
4.2495
4.2485
4.4995
4.4985
4.7495
4.7485
0.0020
0.0005
0.0020
0.0005
0.0030
0.0005
0.0030
0.0005
0.0030
0.0005
0.0040
0.0015
0.0030
0.0005
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0040
0.0010
0.0045
0.0015
0.0045
0.0015
0.0045
0.0015
0.0045
0.0015
0.0050
0.0015
0.0050
0.0015
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0015
0.0050
0.0010
0.0050
0.0010
5.0140
5.0100
5.2540
5.2520
5.2510
5.2490
4.9995
4.9985
0.0050
0.0010
Standard
Length
BMT 0816
1/2 1
1/2, 3/4,1
BMT 1018
5/8 1-1/8
1/2, 3/4,1
BMT 1220
3/4 1-1/4
1/2, 3/4,1
BMT 1422
7/8 1-3/8
BMT 1624
1 1-1/2
3/4, 1, 1-1/2
BMT 1826
1-1/8 1-5/8
3/4, 1, 1-1/2
BMT 2028
1-1/4 1-3/4
1, 1-1/4, 1-1/2
BMT 2230
1-3/8 1-7/8
1, 1-1/4, 1-1/2
BMT 2432
1-1/2 2
1-1/4, 1-1/2, 2
BMT 2634
1-5/8 2-1/8
1-1/4, 1-1/2, 2
BMT 2836
1-3/4 2-1/4
1-1/4, 1-1/2, 2
BMT 3240
2 2-1/2
1-1/2, 2, 3
BMT 3644
2-1/4 2-3/4
1-1/2, 2, 3
BMT 3846
2-3/8 2-7/8
1-1/2, 2, 3
BMT 4048
2-1/2 3
2, 2-1/2, 3
BMT 4250
2-5/8 3-1/8
2, 2-1/2, 3
BMT 4452
2-3/4 3-1/4
2, 2-1/2, 3
BMT 4856
3 3-1/2
2, 2-1/2, 3
BMT 5260
3-1/4 3-3/4
2, 2-1/2, 3
BMT 5664
3-1/2 4
2, 4
BMT 6068
3-3/4 4-1/4
2, 4
BMT 6472
4 4-1/2
2, 4
BMT 6876
4-1/4 4-3/4
2, 4
BMT 7280
4-1/2 5
2, 4
BMT 7684
4-3/4 5-1/4
2, 4
BMT 8088
5 5-1/2
2, 4
Recommended Size
ID
Interference Fit
OD
Housing
Shaft
0.5040
0.5020
0.6290
0.6270
0.7555
0.7525
0.8805
0.8775
1.0055
1.0025
1.1335
1.1305
1.2555
1.2525
1.3830
1.3790
1.5080
1.5040
1.6330
1.6290
1.7580
1.7540
2.0080
2.0040
2.2580
2.2540
2.3850
2.3810
2.5100
2.5060
2.6370
2.6330
2.7620
2.7580
3.0140
3.0100
3.2640
3.2600
3.5140
3.5100
3.7640
3.7600
4.0140
4.0100
4.2640
4.2600
4.5140
4.5100
4.7640
4.7600
1.0025
1.0005
1.1275
1.1255
1.2525
1.2505
1.3785
1.3765
1.5025
1.5005
1.6285
1.6265
1.7535
1.7515
1.8785
1.8765
2.0035
2.0015
2.1285
2.1265
2.2535
2.2515
2.5040
2.5020
2.7540
2.7520
2.8790
2.8770
3.0040
3.0020
3.1290
3.1270
3.2540
3.2520
3.5040
3.5020
3.7540
3.7520
4.0040
4.0020
4.2540
4.2520
4.5040
4.5020
4.7540
4.7520
5.0040
5.0020
5.2540
5.2520
1.0000
0.9995
1.1250
1.1245
1.2500
1.2495
1.3750
1.3745
1.5000
1.4995
1.6250
1.6245
1.7500
1.7495
1.8750
1.8745
2.0000
1.9995
2.1255
2.1245
2.2505
2.2495
2.5005
2.4995
2.7505
2.7495
2.8755
2.8745
3.0005
2.9990
3.1255
3.1240
3.2505
3.2490
3.5010
3.4990
3.7510
3.7490
4.0010
3.9990
4.2510
4.2490
4.5010
4.4990
4.7510
4.7490
5.0010
4.9990
5.2510
5.2490
0.4990
0.4985
0.6240
0.6235
0.7490
0.7485
0.8745
0.8740
0.9990
0.9985
1.1250
1.1245
1.2490
1.2485
1.3745
1.3740
1.4995
1.4990
1.6245
1.6240
1.7495
1.7490
1.9995
1.9985
2.2490
2.2480
2.3750
2.3740
2.4995
2.4990
2.6245
2.6240
2.7495
2.7485
2.9995
2.9985
3.2495
3.2485
3.4995
3.4985
3.7495
3.7485
3.9995
3.9985
4.2495
4.2485
4.4995
4.4985
4.7495
4.7485
0.0030
0.0005
0.0030
0.0005
0.0030
0.0005
0.0040
0.0015
0.0030
0.0005
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0040
0.0010
0.0045
0.0015
0.0045
0.0015
0.0045
0.0015
0.0050
0.0015
0.0050
0.0015
0.0050
0.0015
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
5.0140
5.0100
5.5040
5.5020
5.5010
5.4990
4.9995
4.9985
0.0050
0.0010
16 / 17
Machining
M O ST U F T B e a r i n g s / T h in W a l l - 1 / 1 6
Bearing Nominal Size
Part No.
ID OD
Standard
Length
BMT 0810
1/2 5/8
1/4, 1/2,1
BMT 1012
5/8 3/4
1/4, 1/2,1
BMT 1214
3/4 7/8
1/2, 3/4,1
BMT 1416
7/8 1
BMT 1618
1 1-1/8
3/4, 1, 1-1/2
BMT 1820
1-1/8 1-1/4
3/4, 1, 1-1/2
BMT 2022
1-1/4 1-3/8
1, 1-1/4, 1-1/2
BMT 2224
1-3/8 1-1/2
1, 1-1/4, 1-1/2
BMT 2426
1-1/2 1-5/8
1-1/4, 1-1/2, 2
BMT 2638
1-5/8 1-3/4
1-1/4, 1-1/2, 2
BMT 2830
1-3/4 1-7/8
1-1/4, 1-1/2, 2
BMT 3234
2 2-1/8
1-1/2, 2, 3
Recommended Size
ID
Interference Fit
OD
0.5040
0.5020
0.6290
0.6270
0.7555
0.7525
0.8805
0.8775
1.0055
1.0025
1.1335
1.1305
1.2555
1.2525
1.3830
1.3790
1.5080
1.5040
1.6330
1.6290
1.7580
1.7540
2.0080
2.0040
0.6265
0.6255
0.7515
0.7505
0.8765
0.8755
1.0025
1.0005
1.1275
1.1255
1.2525
1.2505
1.3785
1.3765
1.5025
1.5005
1.6285
1.6265
1.7535
1.7515
1.8785
1.8765
2.1285
2.1265
ID
OD
Housing
Shaft
0.6250
0.6245
0.7500
0.7495
0.8750
0.8745
1.0000
0.9995
1.1250
1.1245
1.2500
1.2495
1.3750
1.3745
1.5000
1.4995
1.6250
1.6245
1.7500
1.7495
1.8750
1.8745
2.1255
2.1245
0.4990
0.4985
0.6240
0.6235
0.7490
0.7485
0.8745
0.8740
0.9990
0.9985
1.1250
1.1245
1.2490
1.2485
1.3745
1.3735
1.4995
1.4990
1.6245
1.6240
1.7495
1.7490
1.9995
1.9985
0.0020
0.0005
0.0020
0.0005
0.0020
0.0005
0.0030
0.0005
0.0030
0.0005
0.0030
0.0005
0.0040
0.0010
0.0030
0.0005
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0040
0.0010
Machining of OD
We recommend to grind the outside diameter of composite bearing which is composed
of filament wound fiberglass-epoxy.
Machining of ID
Machining of Mostuf bearing ID depends on the material of bearing layer. MOSTUF T
and MOSTUF F bearing can not be machined because their bearing layers consist of
PTFE fiber. MOSTUF P bearing which consists of filled PTFE Tape and MOSTUF S
bearing which consists of high strength synthetic fiber can be machined by lathe.
Cutting of Bearing
It is desirable to utilize a diamond wheel in order to cut composite bearing materials. In
case of cutting MOSTUF composite bearing on a lathe, it should be cut from inside
diameter in order to prevent any damage in bearing layer.
SOLTRI
M O ST U F P Be a r in g s
Bearing Nominal Size
Part No.
ID OD
Standard
Length
BMP 0812
1/2 3/4
1/2, 3/4,1
BMP 1014
5/8 7/8
1/2, 3/4,1
BMP 1216
3/4 1
1/2, 3/4,1
BMP 1418
7/8 1-1/8
BMP 1620
1 1-1/4
3/4, 1, 1-1/2
BMP 1822
1-1/8 1-3/8
3/4, 1, 1-1/2
BMP 2024
1-1/4 1-1/2
1, 1-1/4, 1-1/2
BMP 2226
1-3/8 1-5/8
1, 1-1/4, 1-1/2
BMP 2428
1-1/2 1-3/4
1-1/4, 1-1/2, 2
BMP 2832
1-3/4 2
1-1/4, 1-1/2, 2
BMP 3236
2 2-1/4
1-1/2, 2, 3
BMP 3240
2 2-1/2
1-1/2, 2, 3
BMP 4044
2-1/2 2-3/4
2, 2-1/2, 3
BMP 4048
2-1/2 3
2, 2-1/2, 3
BMP 4852
3 3-1/4
2, 2-1/2, 3
BMP 4856
3 3-1/2
2, 2-1/2, 3
BMP 5664
3-1/2 4
2, 4
BMP 6472
4 4-1/2
2, 4
BMP 8088
5 5-1/2
2, 4
Recommended Size
0.5040
0.5020
0.6290
0.6270
0.7555
0.7525
0.8805
0.8775
1.0055
1.0025
1.1335
1.1305
1.2555
1.2525
1.3830
1.3790
1.5080
1.5040
1.7580
1.7540
2.0080
2.0040
2.0080
2.0040
2.5100
2.5060
2.5100
2.5060
3.0140
3.0100
3.0140
3.0100
3.5140
3.5100
4.0140
4.0100
5.0140
5.0100
0.7515
0.7505
0.8765
0.8755
1.0025
1.0005
1.1275
1.1255
1.2525
1.2505
1.3785
1.3765
1.5025
1.5005
1.6285
1.6265
1.7535
1.7515
2.0035
2.0015
2.2535
2.2515
2.5040
2.5020
2.7540
2.7520
3.0040
3.0020
3.2540
3.2520
3.5040
3.5020
4.0040
4.0020
4.5040
4.5020
5.5040
5.5020
Interference Fit
Housing
Shaft
0.7500
0.7495
0.8750
0.8745
1.0000
1.9995
1.1250
1.1245
1.2500
1.2495
1.3750
1.3745
1.5000
1.4995
1.6250
1.6245
1.7500
1.7495
2.0000
1.9995
2.2505
2.2495
2.5005
2.4995
2.7505
2.7495
3.0005
2.9990
3.2505
3.2490
3.5010
3.4990
4.0010
3.9990
4.5010
4.9990
5.5010
4.4990
0.4995
0.4985
0.6245
0.6235
0.7490
0.7485
0.8745
0.8735
0.9995
0.9985
1.1245
1.1235
1.2495
1.2485
1.3745
1.3735
1.4995
1.4990
1.7495
1.7480
1.9995
1.9980
1.9995
1.9980
2.4995
2.4975
2.4995
2.4975
2.9995
2.9975
2.9995
2.9975
3.4995
3.4965
3.9995
3.9965
4.9995
4.9960
0.0020
0.0005
0.0020
0.0005
0.0030
0.0005
0.0030
0.0005
0.0030
0.0005
0.0040
0.0015
0.0030
0.0005
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0040
0.0015
0.0045
0.0015
0.0045
0.0015
0.0050
0.0015
0.0050
0.0015
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
0.0050
0.0010
Limited Warranty
For a period of 6 months from the date of first sale, Soltri Corporation warrants this product(s) to be
free defects in manufacturing. Our only obligation will be to provide replacement product for any
portion proving defective, or at our option, to refund the purchase price thereof. User assumes all
other risks, if any, including the risk of injury, loss or damage, whether direct or consequential, arising
out of the use, misuse, or inability to use this product(s). SOLTRI CORPORATION DISCLAIMS ANY
AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
NOTE
Soltri Corporation does not assume any responsibility or liability for any advice furnished by it, or for
the performance or results of any installation or use of the product(s) or of any final product into
which the product(s) may be incorporated by the purchaser and/or user. The purchaser and/or user
should perform its own tests to determine the suitability and fitness of the product(s) for the particular
purpose desired in any given situation.
18 / 19