The document provides service information for CD mechanisms. It begins with warnings about the laser beam and instructions for safe servicing. Diagrams and part lists are provided to illustrate the components. Technical specifications and operating instructions are described, including adjusting the rotating phase of gears. Waveform diagrams show normal voltage levels.
The document provides service information for CD mechanisms. It begins with warnings about the laser beam and instructions for safe servicing. Diagrams and part lists are provided to illustrate the components. Technical specifications and operating instructions are described, including adjusting the rotating phase of gears. Waveform diagrams show normal voltage levels.
The document provides service information for CD mechanisms. It begins with warnings about the laser beam and instructions for safe servicing. Diagrams and part lists are provided to illustrate the components. Technical specifications and operating instructions are described, including adjusting the rotating phase of gears. Waveform diagrams show normal voltage levels.
The document provides service information for CD mechanisms. It begins with warnings about the laser beam and instructions for safe servicing. Diagrams and part lists are provided to illustrate the components. Technical specifications and operating instructions are described, including adjusting the rotating phase of gears. Waveform diagrams show normal voltage levels.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 22
BZG-2
English
SERVICE MANUAL CD MECHANISM BASIC CD MECHANISM :KSM2131FAM TYPE ZD4NC YZD4NC ZD4N YZD4NCC BASIC CD MECHANISM KSM-2131FAM KSM-2131FAM KSM-2131FAM KSM-2131FAM
S/M Code No. 09-00C-353-2N2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling.
ATTENTION L'utilisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations.
ADVARSEL! Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saattaa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle.
VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlning, som verskrider grnsen fr laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
-2-
Precaution to replace Optical block (KSS-213F)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
-3-
How to Adjust the Rotating Phase of the Gear, Main Cam
1) Push down the hooking catch of the CHAS. MECH, and remove the TRAY. 2) Align the arrow mark of the Gear, Main Cam with the black round mark of the CHAS, MECHA as shown below. 3) Confirm that the Slide, Mech Cam is located in the right position, then insert the TRAY gently. Caution: If the rotating phase of the Gear, Main Cam is incorrectly adjusted, the chucking operation and tray movement will have malfunction.
CAP,TC U 0.1-50 Z F CONN,05P H 9604S-05F MOT,M25E-4 2054 SNSR,SG-240
9X-262-513-210 91-564-722-110 91-572-085-110
SLED MOTOR CONNECTOR 6P LEAF SW
-5-
ELECTRICAL MAIN PARTS LIST-2/2
Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8 A Resistor Code Value of resistor Chip resistor Dimensions (mm)
IC DESCRIPTION-1/1 (LC78645)-1/3 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25, 26 Pin Name SLCO SLCIST EFMIN RF RFVDD RFVSS FIN1 FIN2 TIN1 TIN2 VREF REFI EF TEC TE RFMON JITTC ADAVDD ADAVSS TDO FDO SPDO SLDO GPDAC CONT4, 5 I/O O I I O I I I I O I O O O O O O O O O O I/O RF monitor pin. RF power supply pin. RF ground pin. Must be connected to 0V. A+C signal input pin. B+D signal input pin. E signal input pin. F signal input pin. VREF voltage output pin. Reference voltage output setting pin. FE signal monitor pin. TE signal LPF capacitor connection pin. TE signal monitor pin. RF internal signal monitor pin. Jitter detection capacitor connection pin. Servo A/D, D/A supply pin. Servo A/D, D/A ground pin. Must be connected to 0V. Tracking control output pin. D/A output. Focus control output pin. D/A output. Spindle control output pin. D/A output. Thread control output pin. D/A output. Servo D/A general-purpose output pin. (Not connected) General-purpose input/output pin 4, 5. General-purpose input/output pin 6, 27 SBCK/CONT6 I/O or subcode read clock input pin. Controlled by commands from the microprocessor. Any of these that are unused must be either set up as input pin ports and connected to 0V, or set up as output pin ports and left open. 28 29 30 SBCK/FG DEFECT V/P I O O Subcode read clock input pin/FG signal input pin/external emphasis setting pin. Set to command -pin function. Must be connected to 0V. Defect pin. (Not connected) Rouge servo/phase control automatic switching monitor output pin. H for rough servo and L for phase servo. (Not connected) Synchronization signal detection output pin. 31 FSEQ O Outputs a high level when the synchronization signal detected from the EFM signal and the internally generated synchronization signal agree. (Not connected) 32-36 37 38 39 40 MONI1, 5 VSS VDD DOUT TEST O O I Internal signal monitor pin 1, 5. (Not connected) Digital ground pin. Must be connected to 0V. Digital power supply pin. Digital OUT output pin. (Not connected) Test input pin. Must be connected to 0V. Slice level control Control output. SLCO output current adjustment resistor connection pin. RF signal input pin. Description
-14-
IC DESCRIPTION-1/1 (LC78645)-2/3 Pin No. 41 42 43 44 45 46 47 48 49 50 Pin Name LVDD LCHO LVSS RVSS RCHO RVDD XVDD XOUT XIN FSX/16MIN I/O O O O I I/O 7.35kHz synchronization signal output pin. DF, DAC external clock input pin. (Not connected) 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 XVSS C2F EFLG 16MOUT ASLRCK ASDACK ASDFIN LRSY DATACK DATA CE CL DI DO WRQ RES DRF VDD5 VSS CONT3 O O O I I I O O O I I I O O I O I/O Reset input pin. This pin must be set low briefly after power is first applied. Focus ON detect pin. Microprocessor interface power supply pin. Digital ground pin. Must be connected to 0V. General-purpose output pin 3. (Not connected) Controlled by commands from the microprocessor . 71, 72 CONT2, 1 I/O General-purpose output pin 2, 1. Must be set as an input pin and connected to 0V or set as an output pin and left open when unused. Microprocessor interface Digital data output Antishock mode Crystal oscillator Crystal oscillator ground pin. Must be connected to 0V. C2 flag output pin. (Not connected) C1, C2 error correction monitor pin. (Not connected) 16.9344MHz output pin. (Not connected) L/R clock input pin. Must be connected to 0V when unused. Bit clock input pin. Must be connected to 0V when unused. L/R channel data input pin. Must be connected to 0V when unused. L/R clock output pin. (Not connected) Bit clock output pin. (Not connected) L/R channel data output pin. (Not connected) Chip enable signal input pin. Data transfer clock input pin. Data input pin. Data output pin. (Nch open drain output) Interruption signal output pin. Crystal oscillator R channel D/A converter L channel D/A converter Description Lchannel power supply pin. L channel output pin. L channel ground pin. Must be connected to 0V. R channel ground pin. Must be connected to 0V. R channel output pin. R channel power supply pin. Crystal oscillator power supply pin. Connection for a 33.8688MHz crystal oscillator pin.
-15-
IC DESCRIPTION-1/1 (LC78645)-3/3 Pin No. 73, 74 75 76 77 78 79 80 Pin Name PD01, 2 VVSS PCKIST VVDD FR LDS LDD I/O O I I I O PLL Description Phase comparison output pin 1, 2 to control built-in VCO. Built -in VCO GND pin. Must always be connected to 0V. Resistor connection pin to set current for PD01 and 02 outputs. Built-in VCO power supply pin. Resistor connection pin to set the frequency range of built-in VCO. Laser power detection signal input pin. Laser power control signal output pin.
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green YM Metallic Yellow DM Metallic Orange PT Transparent Pink LA Aqua Blue GL Light Green
