TM 9-2350-247-20-3

TM 9-2350-247-20-3
TECHNICAL MANUAL
UNIT MAINTENANCE MANUAL
FOR
CARRIER, CARGO TRACKED, 6–TON M548A1
2350–01–096–9356 (EIC AEU)
M548A3
2350–01–369–6081 (EIC AE9)
M548A1 M548A3
SUPERSEDURE NOTICE — This manual supersedes TM 9–2350–247–20-3 dated August 1994, including all changes.
DISTRIBUTION STATEMENT A — Approved for public release; distribution is unlimited.
HEADQUARTERS, DEPARTMENT OF THE ARMY

30 June 2001
TM 9-2350-247-20-3
CHANGE HEADQUARTERS
NO. 1 DEPARTMENT OF THE ARMY
WASHINGTON, D.C., 26 AUGUST 2005
TECHNICAL MANUAL
FOR
CARRIER, CARGO TRACKED, 6-TON

M548A1
2350-01-096-9356 (EIC: AEU)
CARRIER, CARGO TRACKED, 6-TON

M548A3
2350-01-369-6081 (EIC: AE9)
DISTRIBUTION STATEMENT A – Approved for public release; distribution is unlimited.
TM 9-2350-247-20-3, 30 June 2001 is updated as follows:
1. File this change sheet in front of the publication for reference purposes.
2. New or updated text is indicated by a vertical bar in the outer margin of the page.
3. Revised illustrations are indicated by a miniature pointing hand adjacent to the updated area.
4. Remove old pages/Work Packages and insert new pages/Work Packages as indicated below.
Remove Pages/Work Packages Insert Pages/Work Packages
Cover Cover
A/B blank A/B blank
i – xvii/xviii blank i – vi
Chapter 18 WP Index Chapter 18 WP Index
None WP 0405 01
WP 0406 00 WP 0406 00
WP 0416 00 WP 0416 00
Chapter 20 WP Index Chapter 20 WP Index
WP 0420 00 – 0421 00 WP 0420 00 – 0421 00
WP 0423 00 None
WP 0428 00 WP 0428 00
WP 0436 00 WP 0436 00
WP 0445 00 WP 0445 00
WP 0447 00 WP 0447 00
WP 0449 00 WP 0449 00
WP 0454 00 WP 0454 00
WP 0513 00 – 0514 00 WP 0513 00 – 0514 00
WP 0539 00 – 0542 00 WP 0539 00 – 0542 00
Index-1 – Index-47/48 blank Index-1 – Index-53/54 blank
None Sample Form 2028
DA Form 2028 (3) DA Form 2028 (3)
Metric Chart/Back Cover Metric Chart/Back Cover
TM 9-2350-247-20-3
By Order of the Secretary of the Army:
PETER J. SCHOOMAKER
General, United States Army
Official: Chief of Staff
SANDRA R. RILEY
Administrative Assistant to the
Secretary of the Army
0519904
DISTRIBUTION:
To be disbributed in accordance with the initial distribution number (IDN) 373282 requirements for
TM 9-2350-247-20-3.
TM 9-2350-247-20-3
INSERT LATEST UPDATED PAGES/WORK PACKAGES. DESTROY SUPERSEDED DATA.
LIST OF EFFECTIVE PAGES/WORK PACKAGES

Note: Updates to all portions of this TM are indicated by a vertical bar in the outer margin of the page.
Dates of issue for original and updated pages/work packages are:
Original 0 (30 June 2001)

Change 1 (26 August 2005)
TOTAL NUMBER OF PAGES FOR FRONT AND REAR MATTER IS 82 AND TOTAL
NUMBER OF WORK PACKAGES IS 164 CONSISTING OF THE FOLLOWING:
Page/WP *Change Page/WP *Change Page/WP *Change

No. No. No. No. No. No.
Cover 1 WP 0516 00 – 0523 00 0
Transmittal/Authentication 1 Chapter 24 WP Index 0
A/B blank 1 WP 0524 00 – 0529 00 0
i – vi 1 Chapter 25 WP Index 0
Chapter 17 WP Index 0 WP 0530 00 – 0538 00 0
WP 0379 – 0381 00 0 Chapter 26 WP Index 0
Chapter 18 WP Index 1 WP 0539 00 – 0542 00 1
WP 0382 00 – 0405 00 0 Index 1 – Index 53/54 blank 1
WP 0405 01 (Added) 1 DA 2028 Sample/Reverse 1
WP 0406 00 1 DA 2028/Reverse (3) 1
Chapter 19 WP Index 0 Authentication Page 0
WP 0407 00 – 0415 00 0 Metric Chart 1
WP 0416 00 1 Back Cover 0
Chapter 20 WP Index 1
WP 0419 00 0
WP 0420 00 – 0421 00 1
WP 0422 00 0
WP 0423 00 (Deleted) 1
WP 0424 00 0
WP 0428 00 1
WP 0429 00 – 0435 00 0
WP 0436 00 1
WP 0437 00 – 0442 00 0
WP 0443 00 0
WP 0444 00 0
WP 0445 00 1
WP 0446 00 0
WP 0447 00 1
WP 0448 00 0
WP 0449 00 1
WP 0450 – 0453 00 0
WP 0454 00 1
WP 0455 00 – 0512 00 0
WP 0513 00 – 0514 00 1
WP 0515 00 0
*Zero in this column indicates an original page
A/B blank
TM 9-2350-247-20-3
HEADQUARTERS
DEPARTMENT OF THE ARMY
WASHINGTON, D.C., 30 June 2001
TECHNICAL MANUAL
CARRIER, CARGO TRACKED, 6–TON M548A1

NSN 2350–01–096–9356
(EIC: AEU)
M548A3
NSN 2350–01–369–6081
(EIC: AE9)
REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

You can help improve this publication. If you find any mistakes or if you know of a way to improve the
procedures, please let us know. Submit your DA Form 2028 (Recommended Changes to Equipment Technical
Publications) through the Internet, on the Army Electronic Product Support (AEPS) website. The Internet
address is http://aeps.ria.army.mil. If you need a password, scroll down and click on “ACCESS REQUEST
FORM.” The DA Form 2028 is located in the ONLINE FORMS PROCESSING section of the AEPS. Fill out the
form and click on SUBMIT. Using this form on the AEPS will enable us to respond quicker to your comments
and better manage the DA Form 2028 program. You may also mail, fax, or email your letter or DA Form 2028
directly to: Technical Publications Office, TACOM-RI, Rock Island, IL 61299–7630. The email address is
[email protected]. The fax number is DSN 793–0726 or Commercial (309) 782–0726.
CURRENT AS OF 5 JANUARY 2004
SUPERSEDURE NOTICE — This manual supersedes TM 9–2350–247–20–3 dated August 1994.
DISTRIBUTION STATEMENT A — Approved for public release; distribution is unlimited.
TABLE OF CONTENTS
Volume 3
WP Sequence No.
CHAPTER 17 — UNIT MAINTENANCE INSTRUCTIONS FOR SHOCK ABSORBERS

REPLACE SHOCK ABSORBER.......................................................................................................................0379 00
REPLACE SHOCK ABSORBER PIN................................................................................................................0380 00
REPLACE SHOCK ABSORBER MOUNT.......................................................................................................0381 00
CHAPTER 18 — UNIT MAINTENANCE INSTRUCTIONS FOR HULL

REPLACE LIFTING EYE..................................................................................................................................0382 00
REPLACE HULL BOTTOM ACCESS COVER AND DRAIN COVER..........................................................0383 00
REPLACE TRANSVERSE BEAM AND CENTER SEAT PANEL (M548A1)................................................0384 00
REPLACE TRANSVERSE BEAM BOLTED (M548A3)..................................................................................0385 00
REPLACE CAB DOOR, HANDLES, AND LINKAGE....................................................................................0386 00
i Change 1
TM 9-2350-247-20-3
TABLE OF CONTENTS (cont)

WP Sequence No.
REPLACE DOOR WINDOWS...........................................................................................................................0387 00

REPLACE CAB DOOR SEAL...........................................................................................................................0388 00
REPLACE POWER PLANT RIGHT REAR ACCESS COVER SEAL............................................................0389 00
REMOVE/INSTALL TOP ACCESS COVER AND GRILLES (M548A1).......................................................0390 00
REMOVE/INSTALL FRONT ACCESS COVER (M548A3)............................................................................0391 00
REPLACE WINDSHIELDS AND WINDSHIELD FRAME.............................................................................0392 00
RAISE/LOWER CARGO COMPARTMENT FLOOR PLATES.......................................................................0393 00
REMOVE/INSTALL CAB FLOOR PLATES (M548A1)..................................................................................0394 00
REPLACE CAB FLOOR PLATES, DOOR, AND SEAT SUPPORT (M548A3)..............................................0395 00
REPLACE CENTER SEAT SUPPORT (M548A1)............................................................................................0396 00
REPLACE DRIVER’S SEAT..............................................................................................................................0397 00
REPLACE CAB PERSONNEL SEATS..............................................................................................................0398 00
REPLACE SAFETY BELTS...............................................................................................................................0399 00
REMOVE/INSTALL RIGHT SEAT (M548A1).................................................................................................0400 00
REPLACE M13 DECONTAMINATION BRUSH GUARD AND BACKING PLATE....................................0401 00
REPLACE CARGO DOOR................................................................................................................................0402 00
REPLACE CARGO DOOR SEALS...................................................................................................................0403 00
REPLACE TAILGATE CONTROLS..................................................................................................................0404 00
REPLACE TAILGATE END SEALS AND BUMPERS....................................................................................0405 00
REPLACE T150 TRACK SHOE STOWAGE BRACKET.................................................................................0405 01
REPAIR HULL BY WELDING..........................................................................................................................0406 00
CHAPTER 19 — UNIT MAINTENANCE INSTRUCTIONS FOR WINCH AND

POWER TAKEOFF (M548A1)
REPLACE WINCH (M548A1)...........................................................................................................................0407 00
ADJUST DRUM BRAKE SHOE (M548A1)......................................................................................................0408 00
ADJUST DRUM SAFETY BRAKE (M548A1).................................................................................................0409 00
REPLACE CLUTCH LEVER (M548A1)...........................................................................................................0410 00
REPLACE DRUM LOCK HANDLE (M548A1)...............................................................................................0411 00
REPLACE WINCH PROPELLER SHAFT (M548A1)......................................................................................0412 00
REPLACE WINCH TRANSFER GEARCASE (M548A1)................................................................................0413 00
REPLACE WINCH POWER TAKEOFF CONTROL (M548A1).....................................................................0414 00
REPLACE POWER TAKEOFF (M548A1)........................................................................................................0415 00
REPLACE WIRE ROPE, HOOK, AND CHAIN (M548A1).............................................................................0416 00
CHAPTER 20 — UNIT MAINTENANCE INSTRUCTIONS FOR HULL ACCESSORY ITEMS

REPLACE CARGO COMPARTMENT COVER...............................................................................................0417 00
REPLACE CAB COVER AND FRAMES.........................................................................................................0418 00
REPLACE FRONT STEP...................................................................................................................................0419 00
REPLACE WINDSHIELD WIPER MOTOR.....................................................................................................0420 00
REPLACE WINDSHIELD WIPER LINKAGE.................................................................................................0421 00
REPLACE WINDSHIELD WIPER ARM AND BLADE..................................................................................0422 00
Change 1 ii
TM 9-2350-247-20-3

WP Sequence No.
DELETED............................................................................................................................................................0423 00
REPLACE BILGE PUMP...................................................................................................................................0424 00
REPLACE BILGE PUMP DISCHARGE TUBES AND HOSES (M548A1)....................................................0425 00
REPLACE BILGE PUMP DISCHARGE TUBES AND HOSES (M548A3)....................................................0426 00
SERVICE/REPAIR/ADJUST VEHICLE COMPARTMENT HEATER.............................................................0427 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY AND MOUNTING
BRACKETS (M548A3).............................................................................................................................0428 00
SERVICE VEHICLE COMPARTMENT HEATER FUEL PUMP.....................................................................0429 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY FUEL PUMP
(M548A3)...................................................................................................................................................0430 00
REPLACE VEHICLE COMPARTMENT HEATER CONTROL BOX.............................................................0431 00
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER, HOSES, AND FANS
(M548A3)...................................................................................................................................................0432 00
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN TOGGLE
SWITCHES/IDENTIFICATION PLATE..................................................................................................0433 00
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN WIRING
HARNESS..................................................................................................................................................0434 00
REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS (M548A3).....................................0435 00
SERVICE PERSONNEL HEATER FUEL FILTER ...........................................................................................0436 00
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST METAL HOSE
ASSEMBLY (M548A3).............................................................................................................................0437 00
REPLACE VEHICLE COMPARTMENT HEATER AIR INLET DUCTS (M548A3)......................................0438 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES TO
FUEL/SEPARATOR FILTER (M548A3)..................................................................................................0439 00
REPLACE PLATES, STENCILS, DECALS, RUBBER PADS, AND STRAPS...............................................0440 00
DATA PLATE, MARKER, AND DECAL CHART (M548A1)..........................................................................0441 00
DATA PLATE, MARKER, AND DECAL CHART (M548A3)..........................................................................0442 00
CHAPTER 21 — UNIT MAINTENANCE INSTRUCTIONS FOR TOOLS AND

TEST EQUIPMENT
INSPECT POWER PLANT SLING....................................................................................................................0443 00
CHAPTER 22 — UNIT MAINTENANCE INSTRUCTIONS FOR SPECIAL PURPOSE KITS

REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES, TUBES, AND
FITTINGS (KIT I) (M548A1)...................................................................................................................0444 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES, TUBES, AND
FITTINGS (KIT II OR III) (M548A1)......................................................................................................0445 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY (KIT I) (M548A1)......................................0446 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY (KIT II OR III)
(M548A1)...................................................................................................................................................0447 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP (KIT I) (M548A1).....................................0448 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP AND FUEL FILTER
(KIT II OR III) (M548A1).........................................................................................................................0449 00
REPLACE VEHICLE COMPARTMENT HEATER CONTROLS COVER (M548A1)...................................0450 00
iii Change 1
TM 9-2350-247-20-3

WP Sequence No.
REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS (M548A1).....................................0451 00

REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT I)
(M548A1)...................................................................................................................................................0452 00
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT II)
(M548A1)...................................................................................................................................................0453 00
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT III)
(M548A1)...................................................................................................................................................0454 00
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST GUARD (M548A1).....................................0455 00
REPLACE FIBERGLASS CAB COVER...........................................................................................................0456 00
REPLACE FIBERGLASS MACHINE GUN HATCH COVER........................................................................0457 00
REPLACE CAB WINDOWS..............................................................................................................................0458 00
REPLACE LOWER CAB INSULATION...........................................................................................................0459 00
REPLACE CLOTH SEAT COVERS..................................................................................................................0460 00
REPLACE THERMAL DOOR WINDOWS......................................................................................................0461 00
REPLACE CARGO AREA HEATER AND CONTROL BOX MOUNTING...................................................0462 00
REPLACE CARGO AREA HEATER FUEL LINES, FITTINGS AND SHIELDS..........................................0463 00
REPLACE CARGO AREA HEATER FUEL PUMP..........................................................................................0464 00
REPLACE CARGO AREA HEATER WIRING HARNESS.............................................................................0465 00
REPLACE INSULATED CARGO COVERS.....................................................................................................0466 00
REPLACE ESCAPE HATCH COVER...............................................................................................................0467 00
REPLACE INSULATED COVER WINDOWS.................................................................................................0468 00
REPLACE CARGO DOOR INSULATION........................................................................................................0469 00
REPLACE FLOOR PLATE COVERS................................................................................................................0470 00
REPLACE PERSONNEL SEAT COVERS........................................................................................................0471 00
REPLACE/REPAIR HEATER CONTROL BOX...............................................................................................0472 00
REPLACE ENGINE COOLANT HEATER WIRING HARNESS....................................................................0473 00
REPLACE ENGINE COOLANT HEATER CONTROL BOX..........................................................................0474 00
REPLACE ENGINE COOLANT HEATER FUEL PUMP/FUEL LINES.........................................................0475 00
REPLACE BATTERY BOX HEAT EXCHANGER/HOSES/FITTINGS..........................................................0476 00
REPLACE ENGINE COOLANT HEATER.......................................................................................................0477 00
REPLACE ENGINE COOLANT HEATER COOLANT PUMP.......................................................................0478 00
REPLACE ENGINE COOLANT/VEHICLE COMPARTMENT HEATER EXHAUST
PIPES GUARD (M548A1)........................................................................................................................0479 00
REPLACE ENGINE COOLANT HEATER EXHAUST SYSTEM (M548A1).................................................0480 00
REPLACE ENGINE COOLANT HEATER EXHAUST SYSTEM (M548A3).................................................0481 00
REMOVE/INSTALL MATERIAL HANDLING KIT........................................................................................0482 00
REPLACE BEAM/BEAM SUPPORTS/STOPS.................................................................................................0483 00
REPLACE HOIST/STOPS/SLING.....................................................................................................................0484 00
REPAIR HOIST ASSEMBLY.............................................................................................................................0485 00
REPLACE PERSONNEL SEATS/SAFETY BELT............................................................................................0486 00
REMOVE/INSTALL BULKHEAD PROTECTOR............................................................................................0487 00
Change 1 iv
TM 9-2350-247-20-3

WP Sequence No.
REPLACE RIFLE RACK...................................................................................................................................0488 00

REPLACE AIR BRAKE COMPRESSOR (M548A1)........................................................................................0489 00
REPLACE AIR BRAKE GOVERNOR (M548A1)............................................................................................0490 00
REPLACE AIR BRAKE RESERVOIR (M548A1)............................................................................................0491 00
REPLACE AIR BRAKE SAFETY VALVE (M548A1).....................................................................................0492 00
REPLACE STOPLIGHT SWITCH (M548A1)...................................................................................................0493 00
REPLACE AIR LOW PRESSURE SWITCH (M548A1)...................................................................................0494 00
REPLACE AIR HOSES/TUBES/FITTINGS (M548A1)...................................................................................0495 00
REPLACE OIL HOSES/FITTINGS (M548A1).................................................................................................0496 00
REPLACE COMPRESSOR DRIVE BELT GUARD (M548A1).......................................................................0497 00
ADJUST/ALIGN COMPRESSOR DRIVE PULLEY/BELTS (M548A1).........................................................0498 00
REPLACE COMPRESSOR DRIVE PULLEY/BELTS (M548A1)....................................................................0499 00
REPLACE AIR STRAINER (M548A1).............................................................................................................0500 00
REPLACE AIR BRAKE INSTRUMENT PANEL (M548A1)...........................................................................0501 00
REPLACE AIR LOW PRESSURE WARNING LIGHT (M548A1)..................................................................0502 00
REPLACE AIR BRAKE PRESSURE INDICATOR (M548A1)........................................................................0503 00
REPLACE AIR BRAKE PANEL LIGHT (M548A1).........................................................................................0504 00
REPLACE TURN SIGNAL LIGHT...................................................................................................................0505 00
REPLACE BLACKOUT MARKER LIGHT......................................................................................................0506 00
REPLACE BLACKOUT STOPLIGHT-TAILLIGHT........................................................................................0507 00
REPLACE TURN SIGNAL CONTROL/MOUNT.............................................................................................0508 00
REPLACE FLASHER.........................................................................................................................................0509 00
REPLACE REFLECTOR....................................................................................................................................0510 00
REPLACE TURN SIGNAL FRONT WIRING HARNESS...............................................................................0511 00
REPLACE TURN SIGNAL REAR WIRING HARNESS.................................................................................0512 00
REPLACE CALIBER .50 MACHINE GUN MOUNT.......................................................................................0513 00
REPLACE M66 RING MOUNT KIT.................................................................................................................0514 00
REPLACE 7.62 MM MACHINE GUN MOUNT...............................................................................................0515 00
CHAPTER 23 — UNIT MAINTENANCE INSTRUCTIONS FOR GAUGES

REPLACE SPEEDOMETER..............................................................................................................................0516 00
REPLACE SPEEDOMETER CABLE HOUSING AND ADAPTER................................................................0517 00
REPLACE SPEEDOMETER CABLE................................................................................................................0518 00
REPLACE TACHOMETER................................................................................................................................0519 00
REPLACE TACHOMETER CABLE HOUSING AND ADAPTER (M548A1)...............................................0520 00
REPLACE TACHOMETER CABLE HOUSING AND ADAPTER (M548A3)...............................................0521 00
REPLACE TACHOMETER CABLE (M548A1)...............................................................................................0522 00
REPLACE TACHOMETER CABLE (M548A3)...............................................................................................0523 00
v Change 1
TM 9-2350-247-20-3

WP Sequence No.
CHAPTER 24 — UNIT MAINTENANCE INSTRUCTIONS FOR FIRE

EXTINGUISHER SYSTEM
REPLACE NOZZLES, TUBES, AND FITTINGS (NEW CONFIGURATION)...............................................0524 00
REPLACE NOZZLES, TUBES, AND FITTINGS (OLD CONFIGURATION)................................................0525 00
REPLACE CARBON DIOXIDE (CO2) CYLINDER........................................................................................0526 00
REPLACE FYR-FYTER CONTROL VALVE...................................................................................................0527 00
REPLACE WALTER KIDDE CONTROL VALVE............................................................................................0528 00
REPLACE/REPAIR PORTABLE FIRE EXTINGUISHER PANEL ASSEMBLY
(M548A3)...................................................................................................................................................0529 00
CHAPTER 25 — UNIT MAINTENANCE INSTRUCTIONS FOR NBC SYSTEM (M548A3)

REPLACE NBC CIRCUIT BREAKER AND RELAY (M548A3)....................................................................0530 00
REPLACE NBC WIRING HARNESS FROM BATTERY COMPARTMENT TO
MANIFOLD (M548A3).............................................................................................................................0531 00
REPLACE NBC M3 HEATER AND ADAPTER (M548A3)............................................................................0532 00
REPAIR NBC MANIFOLD (M548A3)..............................................................................................................0533 00
REMOVE/INSTALL NBC M1A1-19 PRECLEANER ASSEMBLY AND FRAME
(M548A3)...................................................................................................................................................0534 00
REPLACE NBC M1A1-19 PARTICULATE FILTER UNIT (M548A3)............................................................0535 00
REPLACE NBC M18 FILTER (M548A3)..........................................................................................................0536 00
REPLACE NBC FILTERED AIR HOSE (M548A3)..........................................................................................0537 00
REPLACE NBC ORIFICE CONNECTOR ASSEMBLY AND BRACKET (M548A3)...................................0538 00
CHAPTER 26 — UNIT SUPPORTING INFORMATION

REFERENCES....................................................................................................................................................0539 00
MAINTENANCE ALLOCATION CHART (MAC)...........................................................................................0540 00
COMMON TOOLS AND SUPPLEMENTS AND SPECIAL TOOLS/FIXTURES LIST................................0541 00
EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST..................................................................0542 00
Change 1 vi
TM 9-2350-247-20-3
CHAPTER 17
UNIT MAINTENANCE INSTRUCTIONS
FOR SHOCK ABSORBERS
WORK PACKAGE INDEX

Title Sequence No.
REPLACE SHOCK ABSORBER......................................................................................................................................0379 00
REPLACE SHOCK ABSORBER PIN..............................................................................................................................0380 00
REPLACE SHOCK ABSORBER MOUNT......................................................................................................................0381 00
TM 9-2350-247-20-3
REPLACE SHOCK ABSORBER 0379 00

THIS WORK PACKAGE COVERS:
Removal (page 0379 00-1).

Installation (page 0379 00-3).
INITIAL SETUP:
Maintenance Level Personnel Required

Unit Unit Mechanic
Tools and Special Tools References

General Mechanic’s Tool Kit (WP 0541 00, Item 57) See your -10
Shock Absorber Tool (WP 0541 00, Item 58)
Torque Wrench (WP 0541 00, Item 68) Equipment Condition
Materials/Parts Carrier on level surface
Cotter pin (2) Engine stopped (see your -10)
Inner seal (2) Carrier blocked (see your -10)
Outer seal (2) Respective road wheel removed (WP 0361 00)
REMOVAL
1. Remove two cotter pins (1) and nuts (2) securing shock absorber (3) to hull mount and road arm. Discard cotter pins.
2. Remove two shoulder washers (4) and outer seals (5) from both ends of shock absorber (3). Discard outer seals.
0379 00-1
TM 9-2350-247-20-3
REPLACE SHOCK ABSORBER — Continued 0379 00
3. Position shock remover on hull bracket (6). Hit remover with heavy hammer to loosen upper end of shock absorber (3).
Remove shock remover. Remove shock absorber and inner seal (7) from hull bracket. Discard seal.
4. Position shock remover on support arm pin (8). Hit shock remover with heavy hammer to loosen lower end of shock
absorber (3). Remove shock absorber and inner seal (7) from support arm pin. Discard seal.
0379 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install new inner seal (1) on support arm pin (2).
NOTE
Exercise new shock absorber to the fully extended position and move shock absorber back and
forth several times until resistance can be felt throughout the entire length of the stroke.
Make sure shock absorber is installed with large end of bearing installed first.
2. Install shock absorber (3), new outer seal (4), and shoulder washer (5) on support arm pin (2).
3. Install new inner seal (1), shock absorber (3), new outer seal (4), and shoulder washer (5) on hull bracket (6).
0379 00-3
TM 9-2350-247-20-3
4. Secure shock absorber (3) with two nuts (7).

5. Tighten two nuts (7) to 60-80 lb-ft (8-11 N•m) torque. Secure with two new cotter pins (8).
FOLLOW-THROUGH STEPS
1. Install road wheel (WP 0361 00).
2. Road test carrier (WP 0128 00) to check that shock absorber is installed properly.
END OF TASK
0379 00-4
TM 9-2350-247-20-3
REPLACE SHOCK ABSORBER PIN 0380 00


INITIAL SETUP:
Maintenance Level References

Unit See your -10
Tools and Special Tools
General Mechanic’s Tool Kit (WP 0541 00, Item 57) Equipment Condition
Socket Wrench Set (WP 0541 00, Item 65)
Torque Wrench (WP 0541 00, Item 72) Carrier on level surface
Materials/Parts Engine stopped (see your -10)
Lock nut Carrier blocked (see your -10)
Wood blocks Respective road wheel removed (WP 0361 00)
Personnel Required Respective road wheel support arm removed
Unit Mechanic (WP 0351 00)
REMOVAL
1. Remove lock nut (1) from shock absorber pin (2). Discard lock nut.
2. Place road wheel support arm (3) on wood blocks. Drive out shock absorber pin (2) with a wood block and hammer.
0380 00-1
TM 9-2350-247-20-3
REPLACE SHOCK ABSORBER PIN — Continued 0380 00
INSTALLATION
1. Install shock absorber pin (2) in road wheel support arm (3). Secure with new lock nut (1). Tighten lock nut to 210-230
lb-ft (283-310 N•m).
1. Install road wheel support arm (WP 0351 00).
3. Road test carrier (WP 0128 00) to check that shock absorber pin is installed properly.
END OF TASK
0380 00-2
TM 9-2350-247-20-3
REPLACE SHOCK ABSORBER MOUNT 0381 00


INITIAL SETUP:

Unit See your -10
Tools and Special Tools Equipment Condition

General Mechanic’s Tool Kit (WP 0541 00, Item 57) Carrier on level surface
Torque Wrench (WP 0541 00, Item 69) Engine stopped (see your -10)
Personnel Required Carrier blocked (see your -10)
Respective road wheel removed (WP 0361 00)
Unit Mechanic
Respective shock absorber removed (WP 0379 00)
REMOVAL
1. Remove three screws (1) from shock absorber mount (2).
2. Remove shock absorber mount (2) from hull.
0381 00-1
TM 9-2350-247-20-3
REPLACE SHOCK ABSORBER MOUNT — Continued 0381 00
INSTALLATION
1. Place shock absorber mount (2) on hull.
2. Install three screws (1) on shock absorber mount (2). Tighten screws to 130-140 lb-ft (176-190 N•m) torque.
1. Install shock absorber (WP 0379 00).
END OF TASK
0381 00-2
TM 9-2350-247-20-3
CHAPTER 18
FOR HULL
WORK PACKAGE INDEX

Title Sequence No.
REPLACE LIFTING EYE.................................................................................................................................................0382 00

REPLACE HULL BOTTOM ACCESS COVER AND DRAIN COVER........................................................................0383 00
REPLACE TRANSVERSE BEAM AND CENTER SEAT PANEL (M548A1)..............................................................0384 00
REPLACE TRANSVERSE BEAM BOLTED (M548A3)................................................................................................0385 00
REPLACE CAB DOOR, HANDLES, AND LINKAGE..................................................................................................0386 00
REPLACE DOOR WINDOWS.........................................................................................................................................0387 00
REPLACE CAB DOOR SEAL..........................................................................................................................................0388 00
REPLACE POWER PLANT RIGHT REAR ACCESS COVER SEAL...........................................................................0389 00
REMOVE/INSTALL TOP ACCESS COVER AND GRILLES (M548A1).....................................................................0390 00
REMOVE/INSTALL FRONT ACCESS COVER (M548A3)...........................................................................................0391 00
REPLACE WINDSHIELDS AND WINDSHIELD FRAME...........................................................................................0392 00
RAISE/LOWER CARGO COMPARTMENT FLOOR PLATES......................................................................................0393 00
REMOVE/INSTALL CAB FLOOR PLATES (M548A1).................................................................................................0394 00
REPLACE CAB FLOOR PLATES, DOOR, AND SEAT SUPPORT (M548A3).............................................................0395 00
REPLACE CENTER SEAT SUPPORT (M548A1)...........................................................................................................0396 00
REPLACE DRIVER’S SEAT............................................................................................................................................0397 00
REPLACE CAB PERSONNEL SEATS............................................................................................................................0398 00
REPLACE SAFETY BELTS.............................................................................................................................................0399 00
REMOVE/INSTALL RIGHT SEAT (M548A1)................................................................................................................0400 00
REPLACE M13 DECONTAMINATION BRUSH GUARD AND BACKING PLATE...................................................0401 00
REPLACE CARGO DOOR...............................................................................................................................................0402 00
REPLACE CARGO DOOR SEALS..................................................................................................................................0403 00
REPLACE TAILGATE CONTROLS................................................................................................................................0404 00
REPLACE TAILGATE END SEALS AND BUMPERS..................................................................................................0405 00
REPLACE T150 TRACK SHOE STOWAGE BRACKET...............................................................................................0405 01
REPAIR HULL BY WELDING........................................................................................................................................0406 00
Change 1
TM 9-2350-247-20-3
REPLACE LIFTING EYE 0382 00


INITIAL SETUP:

Unit See your -10

General Mechanic’s Tool Kit (WP 0541 00, Item 57) Engine stopped (see your -10)
Socket Wrench Set (WP 0541 00, Item 65) Carrier blocked (see your -10)
Torque Wrench (WP 0541 00, Item 72)
Personnel Required
Unit Mechanic
REMOVAL
NOTE
There are four lifting eyes. Two eyes are located on front of cab compartment. Two eyes are
located in rear of cargo compartment. All four eyes are removed, stowed, and installed the same
way.
1. Remove four screws (1) or two screws (1) and two screws (2) that secure lifting eye (3) to hull.
0382 00-1
TM 9-2350-247-20-3
REPLACE LIFTING EYE — Continued 0382 00
2. If lifting eye is to be stowed, secure eye beneath cargo floor plate.
INSTALLATION
1. If lifting eye has been stowed, remove eye from stowed position.
2. Install lifting eye (3) on hull. Secure with four screws (1) or two screws (1) and two screws (2).
3. Tighten screws (1) and screws (2) to 175-200 lb-ft (237-271 N•m) torque.
END OF TASK
0382 00-2
TM 9-2350-247-20-3
REPLACE HULL BOTTOM ACCESS COVER AND DRAIN COVER 0383 00

INITIAL SETUP:

Unit Unit Mechanic

See your -10
General Mechanic’s Tool Kit (WP 0541 00, Item 57)
Materials/Parts Equipment Condition
Locknut (14) Engine stopped (see your -10)
Carrier blocked (see your -10)
REMOVAL
WARNING
Moving carrier can cause injury or death. Block carrier so it won’t move before removing or
installing access covers.
NOTE
Hull bottom access covers for M548A1 and M548A3 are different. Both access covers are shown.
Do Step 1 for M548A1 hull bottom access covers, then go to Step 3. Do Step 2 for M548A3 hull
bottom access cover, then go to Step 3.
Drain covers for M548A1 and M458A3 are the same and are removed and installed the same
way.
1. Remove eight screws (1) and washers (2) that secure access cover (3) and gasket (4) to hull bottom. Remove cover and
gasket.
0383 00-1
TM 9-2350-247-20-3
REPLACE HULL BOTTOM ACCESS COVER AND DRAIN COVER — Continued 0383 00
2. Remove 14 screws (5) washers (6), and lock nuts (7), that secure cover (8) and gasket (9) to hull bottom. Discard
locknuts.
3. Remove four screws (10) and washers (11) that secure drain cover (12) and gasket (13) to hull bottom. Remove drain
cover and gasket.
4. Check gaskets. Replace gaskets that are cracked, broken, or have hardened.
5. Check access covers and drain covers. Replace parts that are broken, cracked, or deformed.
0383 00-2
TM 9-2350-247-20-3
INSTALLATION
NOTE
Hull bottom access covers for M548A1 and M548A3 are different. Both access covers are shown.
Do Step 2 for M548A1 hull bottom access cover. Do Step 3 for M548A3 hull bottom access cover.
1. Place gasket (1) on drain cover (2). Install drain cover and gasket on hull bottom with four washers (3) and screws (4).
2. Place gasket (5) on access cover (6). Install access cover and gasket on hull bottom with eight washers (7) and screws (8).
0383 00-3
TM 9-2350-247-20-3
3. Place gasket (9) on access cover (10). Install access cover and gasket on hull bottom with 14 screws (11), washers (12),
and new lock nuts (13).
END OF TASK
0383 00-4
TM 9-2350-247-20-3
REPLACE TRANSVERSE BEAM AND CENTER SEAT PANEL (M548A1) 0384 00

INITIAL SETUP:
Maintenance Level Equipment Condition

Unit Engine stopped (see your -10)
Tools and Special Tools Carrier blocked (see your -10)
General Mechanic’s Tool Kit (WP 0541 00, Item 57) Top access covers and grilles removed (WP 0390 00)
Materials/Parts Center seat raised (see your -10)
Lock nut (6) Machine gun mount kit removed (WP 0513 00),
(WP 0514 00), or (WP 0515 00)
Personnel Required
Cab cover removed (WP 0418 00) or (WP 0456 00)
Unit Mechanic
Helper (H) Air cleaner removed (WP 0152 00) or (WP 0159 00)
Primary fuel filter removed (WP 0176 00) or
References (WP 0178 00)
See your -10 Air brake kit removed (WP 0495 00)
0384 00-1
TM 9-2350-247-20-3
REPLACE TRANSVERSE BEAM AND CENTER SEAT PANEL (M548A1) — Continued 0384 00
REMOVAL
1. Remove screw (1), two washers (2), and lock nut (3) that secure panel beam (4) to transverse beam (5). Discard lock nut.
2. Loosen screw (6) at rear end of panel beam (4). Swing panel beam to rear.
3. Remove three screws (7), six washers (8), and three lock nuts (9) that secure right end of transverse beam (5) to right seat
section. Discard lock nuts.
4. Remove two screws (10), four washers (11), and two lock nuts (12) that secure transverse beam (5) to carrier. Discard
lock nuts.
0384 00-2
TM 9-2350-247-20-3
REPLACE TRANSVERSE BEAM AND CENTER SEAT PANEL (M548A1) — Continued 0384 00
INSTALLATION
1. Install two screws (1), four washers (2), and two new lock nuts (3) in transverse beam (4) to secure beam to carrier.
2. Install three screws (5), six washers (6), and three new lock nuts (7) to secure right end of transverse beam (4) to right
seat section.
3. Swing panel beam (8) into place. Install screw (9), two washers (10), and new lock nut (11) to secure panel beam to
transverse beam (4).
4. Tighten screw (12) at rear end of panel beam (8).
1. Install primary fuel filter (WP 0176 00) or (WP 0178 00).
2. Install air cleaner (WP 0152 00) or (WP 0159 00).
3. Install air brake kit (WP 0495 00).
4. Install cab cover (WP 0418 00) or (WP 0456 00).
5. Lower center seat (see your -10).

6. Install top access covers and grilles (WP 0390 00).
7. Install machine gun mount kit (WP 0513 00), (WP 0514 00), or (WP 0515 00).
END OF TASK
0384 00-3/4 blank

TM 9-2350-247-20-3
REPLACE TRANSVERSE BEAM BOLTED (M548A3) 0385 00

INITIAL SETUP:

Unit See your -10
Torque wrench (WP 0541 00, Item 69)
Lock nut (2) Carrier blocked (see your -10)
Shims (as required) Top access cover and grilles removed (see your -10)
Personnel Required Machine gun mount kit removed (WP 0513 00),
Unit Mechanic (WP 0514 00), or (WP 0515 00)
Helper (H) Cab cover removed (WP 0418 00) or (WP 0456 00)
REMOVAL
1. Remove 7 nuts (1), screws (2), and 14 washers (3) that attach center of personnel seat (4) to transverse beam (5).
2. Remove three screws (6), washers (7), and shims (8) from transverse beam (5).
3. Remove two screws (9), washers (10), four washers (11), and lock nuts (12) from transverse beam (5). Discard lock nuts.
0385 00-1
TM 9-2350-247-20-3
REPLACE TRANSVERSE BEAM BOLTED (M548A3) — Continued 0385 00
4. Remove screw (13), washer (14), washer (15), and shims (16) from base of transverse beam (5).
5. Remove transverse beam (5) from carrier. Have helper assist.
0385 00-2
TM 9-2350-247-20-3
REPLACE TRANSVERSE BEAM BOLTED (M548A3) — Continued 0385 00
INSTALLATION
NOTE
In Step 2 and Step 4, install enough shims to ensure transverse beam has a snug fit.
1. Install transverse beam (1) in carrier. Have helper assist.
2. Install screw (2), washer (3), washer (4), and shims (5) through base of transverse beam (1).
3. Install two screws (6), washers (7), four washers (8), and new lock nuts (9). Torque screws to 25-30 lb-ft. (34-41 N•m).
4. Install three screws (10), washers (11), and shims (12) on transverse beam (1).
5. Install 14 washers (13), 7 screws (14), and nuts (15) to secure center of personnel seat (16) to transverse beam (1).
1. Install cab cover (WP 0418 00) or (WP 0456 00).
2. Install top access cover and grilles (see your -10).
3. Install machine gun mount kit (WP 0513 00), (WP 0514 00), or(WP 0515 00).
END OF TASK
0385 00-3/4 blank

TM 9-2350-247-20-3
REPLACE CAB DOOR, HANDLES, AND LINKAGE 0386 00

Disassembly (page 0386 00-3).
Assembly (page 0386 00-5).
Adjustment (page 0386 00-7).
INITIAL SETUP:

Unit Unit Mechanic
General Mechanic’s Tool Kit (WP 0541 00, Item 57) References
Materials/Parts See your -10
Cotter pin
Cotter pin (2)
Equipment Condition
Key washer (2)
Lock nut (6) Engine stopped (see your -10)
Lock washer (4) Carrier blocked (see your -10)
Spring roll pin (2) Cab door window removed (WP 0387 00)
0386 00-1
TM 9-2350-247-20-3
REPLACE CAB DOOR, HANDLES, AND LINKAGE — Continued 0386 00
REMOVAL
1. If carrier has two hinge lugs for each hinge, remove as follows:
a. Remove four hinge lug screws (1), shim washers (2), and hinge lug spacer plate(s) (3) that secure four hinge lugs
(4) to hull. Remove door (5). Separate hinge lugs (4) and hinge lug spacer plate(s) (3) from hinge straps (6).
2. If carrier has a single hinge lug for each hinge, remove as follows:
a. Remove four hinge lug screws (7), washers (8), and hinge lug spacer plate(s) (9) that secure two hinge lugs (10) to
hull. Remove door (5).
0386 00-2
TM 9-2350-247-20-3
DISASSEMBLY
1. Disassemble door handle and latch:
a. Remove latch-to-chain linkage spring roll pin (1) that secures linkage strap link (2) to door latch (3). Disengage
link from latch. Discard spring roll pin.
b. Remove cotter pin (4), outside handle pin (5), and door handle (6). Discard cotter pin.
c. Remove two nuts (7) that secure strap loop (8) to door (9). Remove loop and strap (10).
d. Remove six bracket mounting screws (11), lock nuts (12), and two washers (13) that secure top bracket (14),
bottom bracket (15), lock bracket (16), and latch housing (17) to door (9). Remove brackets and housing. Discard
lock nuts.
e. Separate door latch (3) and spring (18) from latch housing (17). Remove latch spring roll pin (19) from latch.
Discard spring roll pin.
f. Remove two catch screws (20) and key washers (21) that secure catch (22) and backup plate (23) to hull. Remove
catch, catch shim(s) (24), and backup plate. Discard key washers.
0386 00-3
TM 9-2350-247-20-3
2. Disassemble door hinge straps on carriers with two hinge lugs for each hinge.
a. Remove four hinge strap screws (25) and lock washers (26) that secure linkage strap (27), two locking plates (28),
and two hinge straps (29) to door (9). Discard lock washers.
b. Remove two locking plates (28), linkage strap (27), and two hinge straps (29).
3. Disassemble door hinge straps on carriers with a single lug for each hinge.
a. Remove four hinge strap screws (30), lock washers (31), and two hinge locking plates (32) that secure linkage strap
(27) and two hinge straps (33) to door (9). Remove linkage and hinge straps. Discard lock washers.
b. Remove two cotter pins (34), lug washers (35), hinge pin (36), and shim washers (37) (bottom hinge only).
Separate lugs (38), hinge straps (33), and shim washers. Discard cotter pins.
4. Remove two door pad screws (39) and washers (40) that secure door pad (41) to door (9). Remove pad.
0386 00-4
TM 9-2350-247-20-3
ASSEMBLY
1. Place door pad (1) on door (2). Secure with two pad screws (3) and washers (4).
2. Assemble door hinge straps on carriers with two hinge lugs.
a. Place two hinge straps (5), locking plates (6), and front end of linkage strap (7) on door (2). Secure with four hinge
strap screws (8) and new lock washers (9).
3. Assemble door hinge straps on carriers with a single hinge lug.
a. Place two hinge lugs (10) in two hinge straps (11). Secure with two hinge pins (12), shim washers (13), lug
washers (14), and new cotter pin (15).
b. Place two hinge straps (11), locking plates (16), and front end of linkage strap (7) on door (2). Secure with four
hinge strap screws (17) and new lock washers (18).
4. Assemble door handle and latch.

a. Press new latch spring roll pin (19) into door latch (20) so pin extends 1/2 inch (13 mm) out of latch. Assemble
latch spring (21) and door latch (20) into latch housing (22).
b. Place latch housing (22), top bracket (23), bottom bracket (24), and lock bracket (25) on door (2). Secure with six
bracket mounting screws (26), new lock nuts (27), and two washers (28).
c. Attach strap (29) to strap loop (30). Place loop on door (2). Secure with two nuts (31).
d. Place door handle (32) on top bracket (23) and bottom bracket (24). Secure with outside handle pin (33) and new
cotter pin (34).
e. Engage rear end of linkage strap link (35) with door latch (20). Press new latch-to-chain linkage spring roll pin (36)
through linkage and latch so spring pin is centered in latch.
0386 00-5
TM 9-2350-247-20-3
f. Place catch (37), shim(s) (38), and backup plate (39) on hull. Secure with two catch screws (40) and new key
washers (41).
INSTALLATION
1. If carrier has two hinge lugs, install as follows:
a. Install four hinge lugs (1) and spacer plate(s) (2) on two hinge straps (3) of assembled door (4).
b. Place four hinge lugs (1) on hull. Secure with four hinge lug screws (5), lug washers (6), and hinge lug spacer
plate(s) (2).
2. If carrier has a single hinge lug, install as follows:
a. Place two hinge lugs (7) with assembled door (4) on hull. Secure with four hinge lug screws (8), washers (9), and
hinge lug spacer plate(s) (10).
0386 00-6
TM 9-2350-247-20-3
ADJUSTMENT
1. Turn MASTER SWITCH OFF (see your -10).
2. Latch and seal adjustment.
a. Loosen two screws (1). Slide door catch (2) in or out to 1/4-1/2 inch (6-13 mm) compression of door seal (3).
b. Add or remove hinge lug spacer washers (4 or 5) as needed to get 1/4-1/2 inch (6-13 mm) compression of door seal
(3) on hinge side of door.
c. Make sure latch (6) and catch (2) fully engage. If needed, remove two screws (1) and washers (7) that secure catch
to hull. Add or remove shims (8) as needed for full engagement.
d. Install catch (2) with two screws (1) and washers (7).
NOTE
Top edge of door assembly should align with top edge of cowl assembly.
3. Door adjustment (carriers with two hinge lugs).
a. Remove two screws (9), washers (10), and hinge lug spacer washer(s) (5) that secure bottom two hinge lugs (11).
Remove bottom lugs.
b. Add or remove shim washers (12) for proper alignment of door and hull.
c. Install lugs (11) on door hinge strap (13).
d. Put shim washers (12) in place. Secure with two screws (9), washers (10), and hinge lug washer(s) (5).
4. Door adjustment (carriers with single hinge lug).
a. Remove lower hinge cotter pin (14), washer (15), and pin (16). Add shim washer(s) (17) to get proper door and
hull alignment. Discard cotter pin.
b. Install hinge pin (16), washer (15), and new cotter pin (14).
1. Install cab door window (WP 0381 00).
END OF TASK
0386 00-7/8 blank

TM 9-2350-247-20-3
REPLACE DOOR WINDOWS 0387 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Adhesive (WP 0542 00, Item 2) Equipment Condition
Rubber adhesive tape (WP 0542 00, Item 32) Engine stopped (see your -10)
0387 00-1
TM 9-2350-247-20-3
REPLACE DOOR WINDOWS — Continued 0387 00
REMOVAL
NOTE
Left and right door windows are removed the same way. Normally, complete disassembly of cab
door window is not needed. Remove only those parts that inspection shows are faulty.
1. Remove two screws (1) and washers (2). Remove window frame (3) from cab door.
2. Remove handle retainer pin (4) that secures spring end of sliding window handle (5). Remove handle and handle spring
(6) from sliding window bottom channel (7). Remove spring retainer from bottom channel.
3. Slide glass (8) to front. Remove four screws (9) that secure rear glass run channel (10). Return glass to rear position.
Remove one screw and channel.
4. Remove four screws (11) that secure front glass run channel (12). Remove channel.
5. Remove two screws (1) and lock nuts (2) that secure two fixed window retainers (3) to window frame (4). Remove
retainers. Discard lock nuts.
0387 00-2
TM 9-2350-247-20-3
6. Slide glass (5) toward rear. Remove glass, channel (6), and weatherstrip channel (7) as a unit from window frame (4).
7. Remove bottom channel (8), sealing tape (9), top channel (10), rear channel (11), stop channel (12), only when
replacement is needed.
8. If needed, remove window seal (13) and window-to-door seal (14) and window-to-door seal (15) from grooves in
window frame (4).
0387 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Clean grooves in window frame (1) and back of window seal (2). Apply a light coat of adhesive to mating surfaces.
Install seal.
2. Clean groove in window frame (1). Install window-to-door seal (3) and window-to-door seal (4).
3. Clean channel (5), channel (6), and channel (7) and groove in window frame (1). Apply a light coat of adhesive to
mating surfaces. Install channels in window frame.
4. Clean window (8). Apply a strip of rubber adhesive tape (9) centered lengthwise on bottom edge of glass. Trim tape
ends. Install sliding window bottom channel (10) on glass.
5. Clean window glass (8). Install window channel (11).
6. Clean rear edge of window glass (8) and inside weatherstrip channel (12) surfaces. Apply a light coat of adhesive to
mating surfaces. Install channel on rear edge of glass.
7. Slide window glass (8) with channel (11) and weatherstrip channel (12) as a unit forward into groove in window
frame (1).
0387 00-4
TM 9-2350-247-20-3
NOTE
Weatherstrip channel (12) must be toward center of window.
8. Place two window retainers (13) on window frame (1). Secure with two screws (14) and new lock nuts (15).
9. Place front glass run channel (16) on window frame (1). Secure with four screws (17).
0387 00-5
TM 9-2350-247-20-3
10. Place window glass (1) and bottom channel (2) as a unit into rear glass run channel (3). Place glass and two channels in
window frame (4). Slide glass to forward position. Secure channel (3) with four screws (5). Return glass to rear
position. Install one screw in channel.
11. Insert sliding window handle (6) through mounting tube on sliding window bottom channel (2). Install handle spring (7)
on handle. Secure with handle retainer pin (8).
12. Install window frame (4) in cab door using two screws (9) and washers (10).
END OF TASK
0387 00-6
TM 9-2350-247-20-3
REPLACE CAB DOOR SEAL 0388 00

Cleaning (page 0388 00-1).
INITIAL SETUP:

Unit
See your -10

Adhesive (WP 0542 00, Item 2)
Engine stopped (see your -10)
Cleaning compound (WP 0542 00, Item 9)
Unit Mechanic Cab door removed (WP 0386 00)
REMOVAL
1. Bend retaining strip (1) away from door (2) to release seal (3).
2. Remove door seal (3) from cab door (2).
CLEANING
1. Clean door edge with cleaning compound. Remove all adhesive and particles of old seal. Make sure door edge is clean
and dry before installing door seal.
0388 00-1
TM 9-2350-247-20-3
REPLACE CAB DOOR SEAL — Continued 0388 00
INSTALLATION
1. Coat lower corners of seal and edge of door (2) with adhesive. Allow to dry until tacky.
2. Place door seal (3) beneath retaining strip (1) on cab door (2). Press firmly into place.
3. Bend retaining strip (1) to secure seal (3) on door (2).
1. Install cab door (WP 0386 00).
2. Adjust cab door (WP 0386 00).
END OF TASK
0388 00-2
TM 9-2350-247-20-3
REPLACE POWER PLANT RIGHT REAR ACCESS COVER SEAL 0389 00

INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
General Mechanics Tool Kit (WP 0541 00, Item 57)
Adhesive (WP 0542 00, Item 2) Engine stopped (see your -10)
Cleaning compound (WP 0542 00, Item 9) Carrier blocked (see your -10)
Seal Power plant right rear access cover removed
(see your -10)
REMOVAL
NOTE
Right rear access cover seal for M548A1 and M548A3 is replaced the same way. M548A1 right
rear access cover seal is shown.
1. Remove seal (1) from right rear access cover (2).
0389 00-1
TM 9-2350-247-20-3
REPLACE POWER PLANT RIGHT REAR ACCESS COVER SEAL — Continued 0389 00
INSTALLATION
1. Clean mating surfaces of right rear access cover (2) and seal (1) with cleaning compound.
2. Put a thin coat of adhesive on mating surfaces of right rear access cover (2) and seal (1). Allow to dry until tacky.
3. Press seal (1) on right rear access cover (2) firmly.
1. Install power plant right rear access cover (see your -10).
END OF TASK
0389 00-2
TM 9-2350-247-20-3
REMOVE/INSTALL TOP ACCESS COVER AND GRILLES (M548A1) 0390 00

INITIAL SETUP:

Unit See your -10

Unit Mechanic Heater exhaust pipe removed (WP 0479 00)
Engine exhaust pipe removed (WP 0209 00)
REMOVAL
1. Loosen four T-handles (1).
2. Turn four clamps (2) and remove access cover (3) and two grilles (4) from carrier.
INSTALLATION
1. Install two grilles (4) and access cover (3) on hull with four clamps (2).
2. Tighten four T-handles (1).
1. Install engine exhaust pipe (WP 0209 00).
2. Install heater exhaust pipe (WP 0479 00).
END OF TASK
0390 00-1/2 blank

TM 9-2350-247-20-3
REMOVE/INSTALL FRONT ACCESS COVER (M548A3) 0391 00


INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Adhesive (WP 0542 00, Item 1) Equipment Condition
Cleaning compound (WP 0542 00, Item 9) Engine stopped (see your -10)
REMOVAL
1. Remove 14 screws (1), lock washers (2), washers (3), front access cover (4), and gasket (5) from carrier. Discard lock
washers.
0391 00-1
TM 9-2350-247-20-3
REMOVE/INSTALL FRONT ACCESS COVER (M548A3) — Continued 0391 00
INSTALLATION
1. Clean surfaces of front access cover (4) and gasket (5) with cleaning compound.
2. Put a thin coat of adhesive on mounting surface of gasket (5).
3. Install gasket (5) on front access cover (4).
4. Install front access cover (4) with gasket (5) on carrier. Secure with 14 washers (3), new lock washers (2), and screws (1).
END OF TASK
0391 00-2
TM 9-2350-247-20-3
REPLACE WINDSHIELDS AND WINDSHIELD FRAME 0392 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Adhesive (WP 0542 00, Item 2) Battery negative lead(s) disconnected (WP 0292 00)
Cleaning compound (WP 0542 00, Item 9) Machine gun mount kit removed, if installed
Spring pin (6) (WP 0513 00), (WP 0514 00), or (WP 0515 00)
Lock nut (8) Cab cover removed, if installed (WP 0417 00)
Seal
Fiberglass cab cover removed, if secondary cab
Personnel Required personnel heater kit is installed (WP 0456 00)
Unit Mechanic Windshield wipers and arms removed (WP 0422 00)
0392 00-1
TM 9-2350-247-20-3
REPLACE WINDSHIELDS AND WINDSHIELD FRAME — Continued 0392 00
REMOVAL
NOTE
Mark locations of right and left hand locking studs for assembly.
Items one and two describe how to remove one windshield glass and window frame. Repeat
these steps for the other windshield windows.
1. Remove spring pins (1) from two thumbscrews (2). Remove thumbscrews (2) and washers (3) from window frame (4).
Discard spring pins.
2. Remove lower filler strip (5) from lower retaining seal (6). Remove strip (7) from retaining seal (8). Remove windshield
glass (9) and seals from each window frame (4).
3. Remove eight lock nuts (1), screws (2), 16 washers (3), eight rubber bushings (4), spacers (5), windshield frame (6), and
frame seal (7) from carrier. Discard lock nuts.
0392 00-2
TM 9-2350-247-20-3
4. Remove seal (8) from window frame (9). Remove old material from frame. Clean frame with cleaning compound.
Discard seal.
INSTALLATION
1. Cement new seal (1) in place on window frame (2) with adhesive.
0392 00-3
TM 9-2350-247-20-3
2. Install frame seal (1) and windshield frame (2) on carrier. Secure with 8 spacers (3), rubber bushings (4), 16 washers (5),
8 screws (6), and new lock nuts (7).
NOTE
Items seven and eight describe how to install one windshield glass and window frame. Repeat
these steps for the other windshield windows.
3. Install retaining seal (1) and lower retaining seal (2) in window frame (3). Install windshield glass (4) in seal. Secure
glass with filler strip (5) and lower filler strip (6).
0392 00-4
TM 9-2350-247-20-3
4. Install two thumbscrews (7) and washers (8) in window frame (3). Secure with two new spring pins (9).
1. Install windshield wipers and arms (WP 0422 00).
2. Install fiberglass cab cover, if removed (WP 0456 00).
3. Install cab cover, if removed (WP 0417 00).
4. Install machine gun mount kit, if removed (WP 0513 00), (WP 0514 00), or (WP 0515 00).
5. Connect battery negative(s) lead (WP 0292 00).
END OF TASK
0392 00-5/6 blank

TM 9-2350-247-20-3
RAISE/LOWER CARGO COMPARTMENT FLOOR PLATES 0393 00


INITIAL SETUP:

Unit See your -10
Equipment Condition
Personnel Required
Unit Mechanic Engine stopped (see your -10)
Helper (H) Carrier blocked (see your -10)
REMOVAL
NOTE
Use a helper. The floor plates are awkward to handle.
1. Remove 14 screws (1) and spacers (2). Lift out floor plates (3).
NOTE
If you are adjusting carrier for high floor position or low floor position, remove floor plate
mounting blocks.
2. Remove 28 screws (4) and washers (5) that secure 14 floor plate mounting blocks (6) to hull.
0393 00-1
TM 9-2350-247-20-3
RAISE/LOWER CARGO COMPARTMENT FLOOR PLATES — Continued 0393 00
3. If rear lifting eyes (7) need to be stowed, remove eight screws (8) that secure lifting eyes on sponson (9). Fasten lifting
eyes in stowed position on hull crossmember (10) (see your -10).
INSTALLATION
NOTE
If adjusting floor plate mounting blocks (6) for high floor position, install seven mounting blocks
on each sponson (9). If adjusting floor plate mounting blocks for low floor position, install four
mounting blocks (6) along front of each sponson. Stow other six mounting blocks on the hull
crossmember (10).
1. Put 14 floor plate mounting blocks (6) in place. Secure with 28 screws (4) and washers (5).
2. Put floor plates (3) in place. Secure with 14 spacers (2) and screws (1).
END OF TASK
0393 00-2
TM 9-2350-247-20-3
REMOVE/INSTALL CAB FLOOR PLATES (M548A1) 0394 00

Removal of Center Floor Plates (page 0394 00-1).

Installation of Center Floor Plates (page 0394 00-2).
Removal of Left Floor Plate (page 0394 00-2).
Installation of Left Floor Plate (page 0394 00-3).
Removal of Throttle Floor Plate (page 0394 00-3).
Installation of Throttle Floor Plate (page 0394 00-4).
INITIAL SETUP:

Unit See your -10

Personnel Required Engine stopped (see your -10)
Unit Mechanic Carrier blocked (see your -10)
REMOVAL OF CENTER FLOOR PLATES
NOTE
Center floor plates are removed and installed the same way.
1. Unfasten two T-handles (1) and clamps (2). Raise floor plate (3) and secure in open position.
0394 00-1
TM 9-2350-247-20-3
REMOVE/INSTALL CAB FLOOR PLATES (M548A1) — Continued 0394 00
INSTALLATION OF CENTER FLOOR PLATES
1. Lower floor plate (3) and secure to cab floor with two T-handles (1) and clamps (2).
REMOVAL OF LEFT FLOOR PLATE
1. Remove six screws (1), washers (2), and left floor plate (3) from carrier.
0394 00-2
TM 9-2350-247-20-3
INSTALLATION OF LEFT FLOOR PLATE

1. Install left floor plate (3) in carrier with six screws (1) and washers (2).
REMOVAL OF THROTTLE FLOOR PLATE

1. Remove 9 screws (4), 12 washers (5), 3 nuts (6), and throttle floor plate (7) from carrier.
0394 00-3
TM 9-2350-247-20-3
INSTALLATION OF THROTTLE FLOOR PLATE

1. Install throttle floor plate (7) in carrier with 9 screws (4), 12 washers (5), and 3 nuts (6).
END OF TASK
0394 00-4
TM 9-2350-247-20-3
REPLACE CAB FLOOR PLATES, DOOR, AND SEAT SUPPORT (M548A3) 0395 00
INITIAL SETUP:

Unit See your -10
Cotter pin (2)
Lock nut (13)
Unit Mechanic Center seat raised (see your -10)
0395 00-1
TM 9-2350-247-20-3
REPLACE CAB FLOOR PLATES, DOOR, AND SEAT SUPPORT (M548A3) — Continued 0395 00
REMOVAL
NOTE
Both center floor plates are removed the same way.
1. Remove three screws (1) and washers (2) from floor plate (3) and seat support (4).
2. Remove two screws (5), washers (6), and retaining plates (7) from seat support (4) and cab floor. Remove floor plate (3).
3. Repeat Step 1 and Step 2 for floor plate (8).
0395 00-2
TM 9-2350-247-20-3
4. Remove two lock nuts (9), four washers (10), two screws (11), and support (12) from seat support (4) and hull. Discard
lock nuts.
5. Remove 8 lock nuts (13), 16 washers (14), 8 screws (15), and seat support (4) from hull. Discard lock nuts.
6. Remove 18 screws (16), washers (17), and floor plate (18), floor plate (19), and floor plate (20) from cab floor.
0395 00-3
TM 9-2350-247-20-3
7. Loosen two tee bolts (1). Turn both latches (2) sideways and raise door (3).
8. Remove three lock nuts (4), six washers (5), and three screws (6) securing door hinge (7) to bulkhead. Remove door (3)
and discard lock nuts.
9. Remove two cotter pins (8) from two tee bolts (1). Remove tee bolts with two washers (9) and latches (2) from door (3).
Discard cotter pins.
0395 00-4
TM 9-2350-247-20-3
INSTALLATION
1. Install two tee bolts (1) with two washers (9) and latches (2) into door (3). Install two new cotter pins (8) into threaded
ends of both tee bolts.
2. Position door (3) on cab floor. Secure door hinge (7) to bulkhead with three screws (6), six washers (5), and three new
lock nuts (4).
3. Lower door (3). Turn both latches (2) under latch retainers (10) and tighten two tee bolts (1).
0395 00-5
TM 9-2350-247-20-3
4. Install floor plate (1), floor plate (2), floor plate (3), 18 screws (4), and washers (5) on cab floor.
5. Install 8 screws (6), 16 washers (7), 8 new lock nuts (8), and seat support (9) on hull.
6. Install slotted end of support (10) on seat support (9) and hull. Install two screws (11), four washers (12), two new lock
nuts (13), and support on seat support and hull.
0395 00-6
TM 9-2350-247-20-3
NOTE
Both center floor plates are installed the same way.
7. Position floor plate (14) on cab floor. Install two retaining plates (15), screws (16), and washers (17) on seat support (9)
and cab floor.
8. Install three screws (18) and washers (19) on floor plate (14) and seat support (9).
9. Repeat Step 7 and Step 8 for floor plate (20).
END OF TASK
0395 00-7/8 blank

TM 9-2350-247-20-3
REPLACE CENTER SEAT SUPPORT (M548A1) 0396 00

INITIAL SETUP:

Unit See your -10

Materials/Parts Carrier blocked (see your -10)
Top access covers and grilles removed (WP 0390 00)
Lock nut (2) Differential steering controls and bearing unit
Lock nut disconnected from back of center seat support
Lock nut (8) (WP 0366 00)
Personnel Required Center floor plates removed (WP 0394 00)
Unit Mechanic Fuel cutoff control cable disconnected from back of
center seat support (WP 0194 00)
0396 00-1
TM 9-2350-247-20-3
REPLACE CENTER SEAT SUPPORT (M548A1) — Continued 0396 00
REMOVAL
1. Remove two lock nuts (1), four washers (2), two screws (3), and center floor brace (4) from hull. Discard lock nuts.
2. Remove lock nut (5), washer (6) and brace rod (7) from center seat support bracket (8). Discard lock nut.
3. Remove eight lock nuts (9), 16 washers (10), eight screws (11), and center seat support (12) from brackets (13). Discard
lock nuts.
0396 00-2
TM 9-2350-247-20-3
REPLACE CENTER SEAT SUPPORT (M548A1) — Continued 0396 00
INSTALLATION
1. Align center seat support (1) on brackets (2). Secure with eight screws (3), 16 washers (4), and eight new lock nuts (5).
2. Insert brace rod (6) in center seat support bracket (7). Secure with washer (8) and new lock nut (9).
3. Position center floor brace (10) on hull. Secure with four washers (11), two screws (12), and new lock nuts (13).
1. Connect fuel cutoff control cable to back of center seat support (WP 0194 00).
2. Install center floor plates (WP 0394 00).
3. Connect differential steering controls and bearing unit to back of center seat support (WP 0366 00).
4. Install top access covers and grilles (WP 0390 00).
END OF TASK
0396 00-3/4 blank

TM 9-2350-247-20-3
REPLACE DRIVER’S SEAT 0397 00

Disassembly(page 0397 00-3).
INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Lock nut (4)
Lock washer (4) Engine stopped (see your -10)
0397 00-1
TM 9-2350-247-20-3
REPLACE DRIVER’S SEAT — Continued 0397 00
REMOVAL
1. Disengage tee handle (1) and clamp (2). Tilt seat forward.
2. Remove four nuts (3) and washers (4) that secure right track assembly (5) and left track assembly (6) to battery
compartment cover (7). Remove seat.
3. Remove battery compartment seal (8) from hull. Check seal for signs of wear, brittleness, cracks, or damage. Replace
seal if necessary (WP 0290 00) or (WP 0293 00).
0397 00-2
TM 9-2350-247-20-3
DISASSEMBLY
1. Remove four screws (1) and lock washers (2) that secure backrest support (3) to frame (4). Remove support with
backrest cushion (5). Discard lock washers.
2. Remove 12 screws (6), washers (7), and 4 brackets (8) that secure backrest cushion (5) to backrest support (3). Remove
cushion.
3. Remove seven screws (9), washers (10), two side brackets (11), and one rear bracket (12) that secure cushion (13) to seat
plate (14). Remove cushion.
0397 00-3
TM 9-2350-247-20-3
4. Slide lower portions of right track assembly (15) and left track assembly (16) to rear for access to two front lock nuts
(17). Remove two lock nuts, spacers (18), and screws (19). Discard lock nuts.
5. Slide lower portions of right track assembly (15) and left track assembly (16) to front for access to two rear lock nuts
(17). Remove two lock nuts, spacers (18), four washers (20), and two screws (21). Remove track assemblies and seat
plate (14) from frame (4). Discard lock nuts.
0397 00-4
TM 9-2350-247-20-3
ASSEMBLY
1. Slide lower portion of right track assembly (1) and left track assembly (2) to front. Place track assemblies and seat plate
(3) on frame (4). Secure with two rear screws (5), spacers (6), four washers (7), and two new lock nuts (8).
2. Slide lower portion of right track assembly (1) and left track assembly (2) to rear. Secure track assemblies to seat plate
(3) and frame (4) with two front screws (9), spacers (6), and new lock nuts (8).
0397 00-5
TM 9-2350-247-20-3
3. Place cushion (10) on seat plate (3). Secure with rear bracket (11), two side brackets (12), seven washers (13), and
screws (14).
4. Place backrest cushion (15) on backrest support (16). Secure with 4 brackets (17), 12 washers (18), and screws (19).
5. Place backrest support (16) with backrest cushion (15) on frame (4). Secure with four new lock washers (20) and
screws (21).
0397 00-6
TM 9-2350-247-20-3
INSTALLATION
1. If battery compartment seal (1) is replaced, see (WP 0290 00) or (WP 0293 00).
2. Place right left track assembly (2) and left track assembly (3) on battery compartment cover (4). Secure with four
washers (5) and nuts (6).
3. Lower seat. Secure with clamp (7) and tee handle (8).
END OF TASK
0397 00-7/8 blank

TM 9-2350-247-20-3
REPLACE CAB PERSONNEL SEATS 0398 00

INITIAL SETUP:

Unit Unit Mechanic
Helper (H)
Materials/Parts
See your -10
Equipment Condition
Lock nut (6)
Lock nut (6) (M548A3) Engine stopped (see your -10)
Lock nut (8) Left grille and access cover removed (WP 0390 00) or
Lock nut (11) (M548A3) see your -10)
0398 00-1
TM 9-2350-247-20-3
REPLACE CAB PERSONNEL SEATS — Continued 0398 00
REMOVAL
NOTE
For M548A1, do Removal Procedure Step 1, Step 2, Step 3, and Installation Procedure Step 3,
Step 4, and Step 5. For M548A3, do Removal Procedure Step 1, Step 4, Step 5, and Installation
Procedure Step 1, Step 2, Step 3, and Step 5.
1. Remove backrest cushions.
a. Remove 6 lock nuts (1), 12 washers (2), and 6 screws (3) that secure backrest cushion (4) to carrier. Discard lock
nuts.
b. Raise three backrest cushions (4) until cushion straps (5) clear retainers on backrest panel (6). Remove cushions.
2. Remove right seat panel with cushion.
a. Remove seven screws (7), washers (8), lock nuts (9), gasket (10), seal (11), seal (12), and seal (13). Remove right
seat panel (14) with cushion (15) from carrier. Discard lock nuts.
b. Remove six seat cushion straps (16) and three seat cushions (15) from carrier.
0398 00-2
TM 9-2350-247-20-3
3. Remove center seat panel.

a. Unfasten center seat strap (17). Raise center seat panel (18).
b. Remove 8 lock nuts (19), 16 washers (20), and 8 screws (21). Remove center seat panel (18), seal (22), seal (23),
rubber strip (24), and rubber strip (25) from carrier. Discard lock nuts. Go to Step 3.
0398 00-3
TM 9-2350-247-20-3
4. Remove lower seat cushions.

a. Remove strap (1) securing crew seat panel (2).
b. Raise crew seat panel (2) and remove six straps (3) and three seat cushions (4).
NOTE
Do Step 5b only if seals or gaskets are damaged.
5. Remove crew seat panel.

a. Remove 11 screws (5), 22 washers (6) and 11 lock nuts (7). Remove crew seat panel (2) from carrier. Have helper
assist. Discard lock nuts.
b. Remove seal (8), seal (9), gasket (10), gasket (11), gasket (12), and gasket (13) from crew seat panel (2).
0398 00-4
TM 9-2350-247-20-3
INSTALLATION
NOTE
Do Step 1a and Step 1b only if seals or gaskets were removed.
1. Install crew seat panel.
a. Clean mating surfaces with cleaning compound.
b. Apply a thin coat of adhesive to mating surfaces. Allow to dry until tacky before installing. Install seal (8), seal (9),
gasket (10), gasket (11), gasket (12), and gasket (13) on crew seat panel (2).
c. Install crew seat panel (2) in carrier with 11 screws (5), 22 washers (6), and 11 new lock nuts (7). Have helper
assist.
2. Install lower seat cushions.
a. Raise crew seat panel (2) and install six straps (3) and three seat cushions (4).
b. Lower crew seat panel (2) and install strap (1) securing crew seat panel. Go to Step 3.
0398 00-5
TM 9-2350-247-20-3
NOTE
To install right seat panel, do Steps 3a - 3c. To install center seat panel, do Step 3a, Step 3d, and
Step 3e.
3. Install right and center seat panels.
a. Clean mating surfaces with cleaning compound.
b. Apply light coat of adhesive to mating surfaces. Allow to dry until tacky. Press gasket (1) and seal (2), seal (3), and
seal (4) in place on seat support (5).
c. Place right seat panel (6) on seat support (5). Secure to carrier with seven new lock nuts (7), washers, (8), and
screws (9).
d. Apply light coat of adhesive to mating surfaces. Allow to dry until tacky. Press seal (10), seal (11), rubber strip
(12), and rubber strip (13) firmly in place on seat support (5).
e. Place center seat panel (14) on seat support (5). Secure to carrier with 8 screws (15), 16 washers (16), and 8 new
lock nuts (17).
4. Install seat cushions.
a. Place seat cushions (18) on right seat panel (6) and on center seat panel (14). Secure with six straps (19).
b. Close center seat panel (14). Secure with center seat strap (20).
5. Install backrest cushions.
a. Lower backrest cushions (21) until cushion straps (22) fit on retainers on backrest panel (23).
b. Install 6 new lock nuts (24), 12 washers (25), and 6 screws (26) to secure backrest cushions (21) to carrier.
0398 00-6
TM 9-2350-247-20-3
1. Install left grille and access cover (WP 0390 00) or see your -10).
END OF TASK
0398 00-7/8 blank

TM 9-2350-247-20-3
REPLACE SAFETY BELTS 0399 00

INITIAL SETUP:

Unit See your -10
Personnel Required Driver’s seat raised (see your -10).
Unit Mechanic Center seat raised (see your -10).
0399 00-1
TM 9-2350-247-20-3
REPLACE SAFETY BELTS — Continued 0399 00
REMOVAL
NOTE
Except for access, safety belts are removed and installed the same way in the M548A1 and
M548A3. In M548A3, the center seat does not need to be opened to remove safety belts.
1. Remove two lock nuts (1), washer (2), and screws (3). Remove right and left safety belts (4). Discard lock nut.
2. Remove lock nut (5), washer (6), and screw (7) that secure two center safety belts (8) to center seat panel (9). Remove
belts. Discard lock nut.
3. Remove lock nut (10), washer (11), and screw (12) that secure two right safety belts (13) between center and right
personnel seats. Remove belts. Discard lock nut.
4. Remove lock nut (14), washer (15), and screw (16) that secure two left safety belts (17) to battery box bulkhead. Remove
belts. Discard lock nut.
0399 00-2
TM 9-2350-247-20-3
REPLACE SAFETY BELTS — Continued 0399 00
INSTALLATION
1. Place two left safety belts (1) on battery box bulkhead. Secure with screw (2), washer (3), and new lock nut (4).
2. Place two right safety belts (5) between center and right personnel seats. Secure with screw (6), washer (7), and new lock
nut (8).
3. Place two center safety belts (9) on center seat panel (10). Secure with screw (11), washer (12), and new lock nut (13).
4. Place left and right safety belts (14) in carrier. Secure with two screws (15), washers (16), and new lock nuts (17).
2. Lower driver’s seat (see your -10).
END OF TASK
0399 00-3/4 blank

TM 9-2350-247-20-3
REMOVE/INSTALL RIGHT SEAT (M548A1) 0400 00

INITIAL SETUP:

Unit See your -10
REMOVAL
1. Remove seven screws (1), washers (2), and right seat (3) from carrier.
0400 00-1
TM 9-2350-247-20-3
REMOVE/INSTALL RIGHT SEAT (M548A1) — Continued 0400 00
INSTALLATION
1. Install right seat (3) in carrier with seven washers (2) and screws (1).
END OF TASK
0400 00-2
TM 9-2350-247-20-3
REPLACE M13 DECONTAMINATION BRUSH GUARD AND BACKING 0401 00

PLATE
INITIAL SETUP:

Unit Unit Mechanic
Helper (H)
Socket Wrench Set (WP 0541 00, Item 64) TM 3-4230-214-12&P
Adhesive (WP 0542 00, Item 2) Carrier blocked (see your -10)
Sealing compound (WP 0542 00, Item 35) M13 portable decontamination unit removed
(TM 3-4230-214-12&P)
0401 00-1
TM 9-2350-247-20-3
REPLACE M13 DECONTAMINATION BRUSH GUARD AND BACKING PLATE — 0401 00

Continued
REMOVAL
WARNING
Use extreme caution when working around the M13 Portable Decontamination Kit which
contains chemical agent DS2, a combustible solution which can cause severe chemical burns.
Wear protective clothing at all times when handling DS2.
NOTE
M13 decontamination brush guard and backing plate are removed and installed the same way
in M548A1 and M548A3. M548A1 brush guard and backing plate shown.
1. Remove 10 screws (1) and washers (2) from guard (3) and backing plate (4). Have helper hold guard.
2. Remove guard (3) from carrier. Have helper assist.
3. (H) Remove backing plate (4) from carrier.
0401 00-2
TM 9-2350-247-20-3
REPLACE M13 DECONTAMINATION BRUSH GUARD AND BACKING PLATE — 0401 00

Continued
CLEANING
1. Use a wire brush to remove any corrosion and sealing compound around mounting holes.
2. Apply sealing compound around mounting holes before installing guard (1).
3. Inspect backing plate (2) for damaged or stripped press nuts (3). Replace as required.
4. Inspect cords (4) for damage. Remove spring pins (5) and elastic cords (4) from guard (1) as required.
5. Inspect upper pad (6) and lower pad (7) for damage. To replace pads, clean mounting surface and apply adhesive as
required.
INSTALLATION
1. (H) Install backing plate (2) against inside of carrier hull.
2. Install guard (1) against front of carrier. Have helper assist.
3. Secure backing plate (2) and guard (1) on carrier with 10 screws (8) and washers (9). Have helper assist.
4. Torque screws (8) to 36-38 lb-ft (51-52 N•m).
1. Install M13 portable decontamination unit (TM 3-4230-214-12&P).
END OF TASK
0401 00-3/4 blank

TM 9-2350-247-20-3
REPLACE CARGO DOOR 0402 00

INITIAL SETUP:

Unit Unit Mechanic
Helper (H)
Suitable Lifting Device
See your -10
Materials/Parts
Cotter pin (4)
Equipment Condition
Grooved pin
Key washer Engine stopped (see your -10)
Spacer plate (as needed) Cargo door opened (see your -10)
0402 00-1
TM 9-2350-247-20-3
REPLACE CARGO DOOR — Continued 0402 00
REMOVAL
NOTE
Cargo door is heavy and awkward. Use helper to remove cargo door.
1. Attach suitable lifting device to support weight of cargo door (1).

2. Remove two nuts (2), four washers (3), and two screws (4) that secure top and bottom hinge pins (5) in left control
bracket (6). Remove two hinge pins. Remove cargo door (1) from carrier and two bottom hull catches (7) (right side
only).
0402 00-2
TM 9-2350-247-20-3
DISASSEMBLY
1. Remove eight screws (1), lock washers (2), four mounting plates (3), and all spacer plates (4) that secure right control
bracket (5) or left control bracket (6) to cargo door (7). Discard lock washers.
2. Remove screw (8) and key washer (9) that secures cargo door handle (10) to right control bracket (5). Discard key
washer.
3. Remove two cotter pins (11) and washers (12) that secure two control links (13) to cargo door handle (10). Remove
handle from right control bracket (5). Discard cotter pins.
0402 00-3
TM 9-2350-247-20-3
4. Remove two cotter pins (14) and washers (15) that secure two handle lock pins (16) to control links (13). Remove links
and lock pins. Discard cotter pins.
5. Remove grooved pin (17) that secures spring (18) on handle latch (19). Remove latch, washer (20), and spring from
bracket (21). Discard grooved pin.
0402 00-4
TM 9-2350-247-20-3
ASSEMBLY
NOTE
To prevent tip of handle latch (5) from pulling through bracket when spring (1) is fully
compressed, install washers (2), as needed behind spring and cotter pin (6).
1. Install spring (1) and washer (2) in bracket (3) on cargo door (4).
2. Install handle latch (5) in bracket (3) on cargo door (4). Secure washer (2) and spring (1) to latch with new cotter pin (6).
3. Install two handle lock pins (7) on two control links (8). Secure pins to links with two washers (9) and new cotter
pins (10).
0402 00-5
TM 9-2350-247-20-3
4. Install two control links (8) assembled with handle lock pins (7) in right control bracket (11).
5. Install cargo door handle (12) on two control links (8). Secure with two washers (13) and new cotter pins (14).
6. Secure cargo door handle (12) in right control bracket (11) with screw (15) and new key washer (16). Bend tabs of key
washer to secure screw.
7. Place left control bracket (17) and right control bracket (11), with controls, on cargo door (4). Secure brackets to door
with four mounting plates (18), eight new lock washers (19), and screws (20).
0402 00-6
TM 9-2350-247-20-3
INSTALLATION
1. Attach suitable lifting device to support weight of cargo door (1).
2. Place cargo door (1) on left control bracket (2) and install top and bottom hinge pins (3). Secure with two screws (4),
four washers (5), and two nuts (6).
3. Remove suitable lifting device.
0402 00-7
TM 9-2350-247-20-3
ADJUSTMENT
1. Loosen four screws (1) in right control bracket (2) or left control bracket (3) to be adjusted.
2. Add or remove spacer plates (4) to produce 1/4 - 1/2 inch (6 - 13 mm) compression of seals.
3. Close cargo door (5) and line up two handle lock pins (6) with top and bottom hull catches (7) (right side only).
4. Secure adjustment with four screws (1).
5. Adjust cargo door handle (8) and linkage on right side of cargo door (5) until two handle lock pins (6) line up with top
and bottom hull catches (7) (right side only).
1. Close cargo door (see your -10).
END OF TASK
0402 00-8
TM 9-2350-247-20-3
REPLACE CARGO DOOR SEALS 0403 00

INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
Cargo door removed (WP 0402 00)
REMOVAL
1. Bend metal retaining strips away from cargo door seal (1). Remove seal from hull.
2. Bend metal retaining strips away from cargo door lower seal (2). Remove seal from cargo door (3).
0403 00-1
TM 9-2350-247-20-3
REPLACE CARGO DOOR SEALS — Continued 0403 00
INSTALLATION
NOTE
Clean all areas with cleaning compound where adhesive is applied. Make sure area is clean and
no old adhesive remains.
1. Apply adhesive to six corners of hull where seal is not held by retaining strips.
2. Place cargo door seal (1) on hull. Bend retaining strips down to secure seal.
NOTE
When installing lower seal (2) on cargo door, make sure ends of seal fit tight against two tailgate
end seals for proper sealing action.
3. Clean area where lower seal (2) attaches to cargo door. Apply adhesive.
4. Place lower seal (2) on cargo door (3). Bend retaining strip down to secure seal.
1. Install cargo door (WP 0402 00).
END OF TASK
0403 00-2
TM 9-2350-247-20-3
REPLACE TAILGATE CONTROLS 0404 00

INITIAL SETUP:

Unit Unit Mechanic

Cotter pin (2) Carrier blocked (see your -10)
Grooved pin Tailgate opened (see your -10)
0404 00-1
TM 9-2350-247-20-3
REPLACE TAILGATE CONTROLS — Continued 0404 00
REMOVAL
NOTE
Right and left tailgate controls are adjusted, removed, and installed the same way.
1. Remove two cotter pins (1), link pins (2), and six washers (3) that secure two connecting links (4) to tailgate handle (5)
and handle eye bolt (6). Remove links and handle. Discard cotter pins.
2. Remove nut (7) and washer (8) that secure handle eye bolt (6) to hull. Remove eye bolt and seal (9). Check seal.
Replace seal if necessary.
3. Remove grooved pin (10) that secures washer (11) and spring (12) to handle latch (13). Remove latch, washer, and
spring from bracket (14). Discard grooved pin.
4. Remove two screws (15). Remove striker plate (16) from tailgate (17).
0404 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Place striker plate (1) on tailgate (2). Secure with two screws (3).
NOTE
To keep tip of latch (6) from pulling through bracket when spring (4) is fully compressed, install
washers (5), as needed, behind spring.
2. Install spring (4), washer (5), and handle latch (6) in bracket (7). Secure spring and washer to bracket with new grooved
pin (8).
3. Install seal (9), if replaced, and handle eye bolt (10) in hull. Secure with washer (11) and nut (12).
4. Place tailgate handle (13) and two connecting links (14) on handle eye bolt (10). Secure links to handle and eye bolt with
six washers (15), two link pins (16), and new cotter pins (17).
0404 00-3
TM 9-2350-247-20-3
ADJUSTMENT
1. Tighten or loosen nut (12) to get 1/4 - 1/2 inch (6 - 13 mm) compression of seal (9).
1. Close tailgate (see your -10).
END OF TASK
0404 00-4
TM 9-2350-247-20-3
REPLACE TAILGATE END SEALS AND BUMPERS 0405 00

INITIAL SETUP:

Unit See your -10
Helper (H) Tailgate opened (see your -10)
0405 00-1
TM 9-2350-247-20-3
REPLACE TAILGATE END SEALS AND BUMPERS — Continued 0405 00
REMOVAL
NOTE
Tailgate is heavy and awkward. Use helper to open/close tailgate.
1. Remove two screws (1) and washers (2) that secure end seal (3) to tailgate (4). Remove end seal.
2. Remove screw (5) and washer (6) that secure tailgate bumper (7) to hull. Remove bumper.
3. Remove nut (8), two washers (9), and one screw (10) that secure bracket (11) and pad (12) to towing eye (13). Remove
bracket and pad.
4. Remove nut (14) that secures pad (12) to bracket (11). Remove pad.
0405 00-2
TM 9-2350-247-20-3
REPLACE TAILGATE END SEALS AND BUMPERS — Continued 0405 00
INSTALLATION
1. Place pad (1) on bracket (2). Secure with nut (3).
2. Place bracket (2) and pad (1) on towing eye (4). Secure with screw (5), two washers (6), and nut (7).
3. Place tailgate bumper (8) on hull. Secure with washer (9) and screw (10).
4. Place end seal (11) on tailgate (12). Secure with two washers (13) and screws (14).
1. Close tailgate (see your -10).
END OF TASK
0405 00-3/4 blank

TM 9-2350-247-20-3
REPLACE T150 TRACK SHOE STOWAGE BRACKET 0405 01

INITIAL SETUP:

Unit See your -10
Personnel Required
Unit Mechanic
REMOVAL
NOTE
There are two brackets to stow track shoes. Both are replaced the same way. Only one is shown.
1. Remove two screws (1), flat washers (2), square flat washers (3), and track shoe assembly (4) from vehicle.
2. Remove two screws (7), flat washers (6), and bracket (5) from vehicle.
0405 01-1
Change 1
TM 9-2350-247-20-3
REPLACE T150 TRACK SHOE STOWAGE BRACKET — Continued 0405 01
INSTALLATION
1. Install bracket (5) on vehicle and secure with two flat washers (6) and screws (7).
2. Install track shoe assembly (4) on vehicle and secure with two square flat washers (3), flat washers (2), and screws (1).
END OF TASK
0405 01-2
Change 1
TM 9-2350-247-20-3
REPAIR HULL BY WELDING 0406 00

Introduction (page 0406 00-1).
Aluminum Castings (page 0406 00-1).
Magnesium Castings (page 0406 00-2).
Equipment and Materials (page 0406 00-2).
Safety Precautions (page 0406 00-3).
Magnesium Casting, Filing, and Grinding (page 0406 00-4).
MIG Welding Method (page 0406 00-4).
INITIAL SETUP:

Unit TC 9-237
TM 5-3431-200-15
Tools and Special Tools TM 5-3431-200-20P
Welder’s Gloves (WP 0541 00, Item 20) Welding Code 12472301
Welder’s Helmet (WP 0541 00, Item 26)
INTRODUCTION
WARNING
Do not attempt to weld aluminum or magnesium castings.
1. This work package shows you how to make basic welding repairs on 5083 aluminum alloy by the MIG (Metal Inert Gas)
method. Also included are safety instructions for filing and grinding magnesium castings. Further welding instructions
are available in TC 9-237 and Welding Code 12472301.
Table 1. ALUMINUM CASTINGS
Component Part Part Number

10949629
Housing, range selector
Controls Lever, left steering Lever, 11588867
right steering
11588949
Housing, input bearing 8656606

Differential
Housing, right angle gearbox 8756602
Final drive Housing assembly 10890371
Transfer gearcase Housing, transfer gearcase 10932771
Transfer gearcase Cover, transfer gearcase 10932773
0406 00-1
Change 1
TM 9-2350-247-20-3
REPAIR HULL BY WELDING — Continued 0406 00
Table 2. MAGNESIUM CASTINGS
Major Component Part Part Number Alloy

Adapter, differential oil
Differential 10865948 AZ91C, 92A
lines
Differential Plate, adapter 8756605 AZ91C, 92A
Differential Retainer, oil seal 10886461 AZ91C, 92A
Differential Housing, differential 8756603 AZ91C, 92A
Cover, differential
Differential 8756613 AZ91C, 92A
housing
Fan Retainer, bearing 10886455 AZ91C, 92A
Fan Retainer, bearing 10886456 AZ91C, 92A
Housing assembly, fan
Fan 10863486 AZ91C
gearbox
Fan, 20 in. diameter
Fan 10865510 AZ91C
cooling
Fan housing, 20 in.
Fan 11616515 AZ91C
diameter
Housing, drive shaft
Fan 8756933 AZ91C
bearing
Fuel compartment Cover, access 10908008 Optional
EQUIPMENT AND MATERIALS

1. Portable welder Linde model number 3431-972-7672 with manufacturer’s manual number 7610-C-12210 or
portable welder Westinghouse model number 3431-879-9709 with TM 5-3431-200-15 and TM 5-3431-200-20P and
manufacturer’s manual number 7610-C-1-2089.
2. Manual welding gun with spool or gun attachment.
3. Voltage control unit.
4. Inert gas supply, regulator-flowmeter, hose and fitting.
5. Number 5356 filler wire.
6. Direct current welding generator (200-ampere minimum capacity).
7. Welding helmet and protective clothing.
0406 00-2
Change 1
TM 9-2350-247-20-3
SAFETY PRECAUTIONS
1. Wear lightproof clothing such as leather or heavy denim. Do not wear clothing with loose pockets, trouser cuffs, short or
rolled up sleeves. Wear welder’s gloves.
2. Do not expose bare skin to welding arc.
3. Do not look directly at welding arc unless you are wearing a welder’s helmet.
4. Wear flash goggles or tinted safety glasses (No. 2) in welding area.
5. Disconnect power source before changing parts or making equipment repairs.
6. Do not touch drive mechanism or any part of electrode.
7. Make sure welding area has plenty of fresh air without being drafty. Remove all poisonous and flammable materials.
8. Make sure all electrical and gas connections are tight.
9. Do not touch any metal in welding area with bare hands. Aluminum does not change color when hot.
0406 00-3
Change 1
TM 9-2350-247-20-3
WARNING
Welding on foam-filled parts is PROHIBITED. Toxic fumes can result in death.
10. Do not weld or use too much heat in areas or carrier where sealing compound (WP 0542 00, Item 33), (WP 0542 00,
Item 36), or (WP 0542 00, Item 38) has been applied or is known to exist. If you must weld in these areas, remove
compound, then clean area with cleaning compound (WP 0542 00, Item 9). After welding, apply new sealing compound
(WP 0542 00, Item 33), (WP 0542 00, Item 36), or (WP 0542 00, Item 38).
a. Foam-filled parts: Driver’s compartment doors.
MAGNESIUM CASTING, FILING, AND GRINDING
WARNING
Do not use water or foam-type extinguishers. These types of extinguishers will intensify
a magnesium fire.
1. Observe special safety precautions when filing or grinding magnesium castings. Fine particles of magnesium are a fire
hazard. See page 0406 00-2 for a list of magnesium castings used on this carrier. Use the following precautions when
working with or near magnesium.
a. Use grinding equipment marked FOR MAGNESIUM GRINDING ONLY.
b. Do not allow magnesium dust or magnesium dust mixtures to accumulate. Keep area clean.
c. Keep tools used to work magnesium sharp.
d. Dispose of grinding sludge immediately.
e. Wear leather or smooth, fire-retardant clothing; brush frequently.
f. Keep fire extinguisher for magnesium handy.
MIG WELDING METHOD
1. MIG (Metal Inert Gas) Welding. This process uses a dc power source, control panel, and a welding gun. The gun feeds a
consumable bare electrode at a given rate into a molten pool beneath a blanket of protective inert gas. When an arc is set
up, a molten pool forms at once. Move the welding gun along the joint line at a rate that shapes the right size bead. The
covering of inert gas keeps air from polluting the weld zone. No flux is needed.
2. Contraction and Expansion. Aluminum welds contract about 6 percent in volume when they become solid after being
melted. Welding at a slow speed may cause too much heating of the area around weld. This will cause the metal to
expand too much. It will then shrink too much when it cools.
3. Filler wire:
a. Always use clean wire. Filler wire polluted by grease, oil, dust, or shop fumes causes porous welds.
b. After welding, cover wire to prevent pollution.
0406 00-4
Change 1
TM 9-2350-247-20-3
c. Store covered wire in warm, dry place.

4. Cleaning of Welding Surfaces. Remove oxides, grease, oil films, and all foreign matter from joint before welding. Brush
well with clean stainless steel wire brush to lower oxide level. Wipe edges of joint with clean cloth dipped in solvent
such as alcohol or acetone to remove remaining foreign matter. Let surfaces dry before welding.
5. Fit-Up and Tacking. Good joint fit-up makes welding easier, saves filler wire and gas, and helps get high quality welds.
You must tack weld to hold the joint members in place if you don’t use jigs. Tack welds should be small, neat, and
placed right to keep parts lined up right before and during welding.
6. Welding Unequal Sections. When welding unequal sections, direct arc against heavier piece to fuse the two edges
evenly. Watch weld pool edges rather than arc to ensure that weld pool edges fuse properly.
7. Multipass Welding:
a. Make sure edges of weld pool fuse right. Watch weld pool edges rather than arc. Any oscillating or weaving
motion should be slight, smooth, and slow.
b. Brush material with clean stainless steel brush after each pass.
c. On small weldments, lower amperage slightly after each pass if welding members become too hot.
8. Lead Angle and Cant Angle. Place gun for lead angle of 10 degrees to 15 degrees off vertical. Point gun in direction of
weld travel for good gas coverage, cleaning, and preheating of material. Place gun for cant angle of 90 degrees to parent
metal so filler wire and arc are directed toward apex of groove. This will give equal fusion on both sides of material,
even weld buildup, good gas coverage, and equal penetration.
9. Nozzle Clearance. Keep nozzle clearance of 1/2 to 5/8 inch (13 to 16 mm) for good gas coverage. Wrong nozzle
clearance will cause the following:
a. Oxidize deposits in the weld bead.
b. Gas bubbles in the weld.
c. No cleaning action on the material in front of the weld pool.
10. Arc length. You will hear a slight hissing or smooth buzzing when the right arc length is struck.
END OF TASK
0406 00-5/6 blank

Change 1
TM 9-2350-247-20-3
CHAPTER 19
FOR WINCH AND POWER TAKEOFF (M548A1)
WORK PACKAGE INDEX

Title Sequence No.
REPLACE WINCH (M548A1)..........................................................................................................................................0407 00
ADJUST DRUM BRAKE SHOE (M548A1)....................................................................................................................0408 00
ADJUST DRUM SAFETY BRAKE (M548A1)...............................................................................................................0409 00
REPLACE CLUTCH LEVER (M548A1).........................................................................................................................0410 00
REPLACE DRUM LOCK HANDLE (M548A1)..............................................................................................................0411 00
REPLACE WINCH PROPELLER SHAFT (M548A1).....................................................................................................0412 00
REPLACE WINCH TRANSFER GEARCASE (M548A1)..............................................................................................0413 00
REPLACE WINCH POWER TAKEOFF CONTROL (M548A1)....................................................................................0414 00
REPLACE POWER TAKEOFF (M548A1).......................................................................................................................0415 00
REPLACE WIRE ROPE, HOOK, AND CHAIN (M548A1)............................................................................................0416 00
TM 9-2350-247-20-3
REPLACE WINCH (M548A1) 0407 00

INITIAL SETUP:

Unit Unit Mechanic
Tools and Special Tools Helper (H)
Torque Wrench (WP 0541 00, Item 69) References
Torque Wrench (WP 0541 00, Item 72) See your -10
Lifting device with rated lift capability of at least 500 lb
(227 kg)
Wiping rag (WP 0542 00, Item 45)
Gasket Battery negative lead disconnected (WP 0292 00)
Gasket (2) Wire rope assembly removed (WP 0416 00)
Screw, 3/4UNCx6 inch Cab center floor plate removed (WP 0394 00)
0407 00-1
TM 9-2350-247-20-3
REPLACE WINCH (M548A1) — Continued 0407 00
REMOVAL
1. Remove two screws (1) and washers (2) from bottom of guard (3).
2. Remove two screws (4), plate (5), and guard (3) from support (6) and safety brake housing.
3. Remove one screw (7) from each end of support (6).
0407 00-2
TM 9-2350-247-20-3
WARNING
Winch weighs more than 400 lbs (181 kg). Use a lifting device with at least 500 lb (227 kg)
capacity to hold winch before removing mounting screws, to prevent personnel injury or
property damage.
4. Remove four screws (1) and two plates (2) from inside power plant compartment.
5. Use helper and lifting device to remove winch from carrier. If winch cannot be moved, remove screw (3) from winch
transfer gear case, and insert a 3/4UNCx6 inch screw. Turn screw until winch moves.
6. Remove gasket (4) from around input shaft (5). Discard gasket. Remove key (6) from shaft.
7. Remove two gaskets (7) from around two pairs of mounting holes on winch. Discard gaskets.
0407 00-3
TM 9-2350-247-20-3
CLEANING
1. Use cleaning compound to clean winch.
2. Check winch. Replace winch that leaks or is cracked or damaged.
3. Clean a 2 x 4 inch (5 cm x 10 cm) area around two pairs of mounting holes where gaskets (7) will be mounted. Clean 3
inch (8 cm) area where gasket (4) will be mounted. Use dry cleaning solvent.
0407 00-4
TM 9-2350-247-20-3
INSTALLATION
1. Apply adhesive to a 2 x 4 inch (5 x 10 cm) area around two pairs of mounting holes where two new gaskets (1) will be
mounted. Apply adhesive to 3 inch (8 cm) area where new gasket (2) will be mounted. Apply adhesive by one of the
following procedures:
a. Apply a thin, even coat of adhesive to each surface. Allow to dry completely. At installation, wet the surface with a
clean cloth dampened in dry cleaning solvent. Press surfaces firmly together.
b. Apply a thin, even coat of adhesive to both surfaces. Allow to dry until it is tacky but no longer transfers to finger
when touched. This takes 10 to 20 minutes. (The higher the temperature, the shorter the drying time.)
2. Apply adhesive to both sides of two gaskets (1) and gasket (2).
3. Install two gaskets (1) on two pairs of mounting holes and gasket (2) on input shaft (3) on winch.
4. Apply adhesive to carrier surfaces that will be touched by two gaskets (1) and gasket (2).
5. Install key (4) on input shaft (3).
6. Reactivate adhesive on winch and carrier if listed above, is being used.
0407 00-5
TM 9-2350-247-20-3
WARNING
Winch weighs more than 400 lbs (181 kg). Use a lifting device with at least 500 lb (227 kg)
capacity to mount winch to prevent personnel injury or property damage.
7. Use helper and lifting device to mount winch on carrier. Make sure you align rear mounting holes in winch with
mounting holes in carrier bulkhead. If holes do not align, turn nuts (5) on tie rod (6) until holes align. Make sure key (4)
mates with splines in transfer gear case.
8. Install two plates (1) and four screws (2) inside power plant compartment. Tighten screws to 90 to 110 lb-ft (122-149
N•m) torque. Bend top corners of plates across flats on screw holes.
9. Place support (3) on winch. Install one screw (4) in each end of support. Tighten screws to 305 to 325 lb-ft (414-441
N•m) torque.
10. Place guard (5) over safety brake housing and on support (3). Install two washers (6) and two screws (7). Do not tighten
screws.
11. Place one plate (8) near end of support (3). Install two screws (9). Install plate and screws on other end of support.
Tighten screws to 90 to 110 lb-ft (122-149 N•m) torque. Bend corners of plates across flats on screw heads.
0407 00-6
TM 9-2350-247-20-3
1. Connect battery negative lead (WP 0292 00).
2. Install cab center floor plate (WP 0394 00).
3. Install wire rope assembly (WP 0416 00).
4. Start engine (see your -10).
5. Reel in wire rope (see your -10). Have helper assist.
6. Check winch for proper operation (see your -10).
7. Stop engine (see your -10).
END OF TASK
0407 00-7/8 blank

TM 9-2350-247-20-3
ADJUST DRUM BRAKE SHOE (M548A1) 0408 00

INITIAL SETUP:

Unit See your -10

General Mechanic’s Tool Kit (WP 0541 00, Item 57) Engine stopped/shutdown (see your -10)
Battery negative lead disconnected (WP 0292 00)
Unit Mechanic
Unlock drum (see your -10)
ADJUSTMENT
NOTE
Drum should turn when wire rope is pulled from winch by hand. It should stop when pulling
stops. Adjust drum shoe if it is too tight or too loose.
1. If wire rope cannot be pulled from winch by hand, loosen screw (1) until drum moves when rope is pulled.
2. If drum keeps turning when pulling stops, tighten screw (1) until drum stops when pulling stops.
2. Lock drum (see your -10).
END OF TASK
0408 00-1/2 blank

TM 9-2350-247-20-3
ADJUST DRUM SAFETY BRAKE (M548A1) 0409 00

INITIAL SETUP:

Unit See your -10

General Mechanic’s Tool Kit WP 0542 00, Item 57 Engine stopped (see your -10)
Socket Wrench Set (WP 0541 00, Item 64) Carrier blocked (see your -10)
Torque Wrench (WP 0541 00, Item 71) Winch drum clutch disengaged (see your -10)
Personnel Required
Unit Mechanic
Helper (H)
ADJUSTMENT
1. Remove two screws (1) and washers (2) from bottom of guard (3).
2. Remove two screws (4) and plate (5) that secure guard (3) to support (6).
0409 00-1
TM 9-2350-247-20-3
ADJUST DRUM SAFETY BRAKE (M548A1) — Continued 0409 00
3. Remove six screws (7), washers (8), cover (9), and gasket (10) from automatic brake case (11).
CAUTION
Engaging PTO to transmission while winch drum clutch is engaged with engine running will
rotate the winch drum. Damage to the wire rope, winch components, or carrier will result.
Ensure winch drum clutch is disengaged.
4. With brake mechanism at room temperature, adjust screw (1) so that brake drum (2) just begins to rotate clockwise when
a torque of 180-204 lb-in (20-23 N•m) is applied to screw (3).
NOTE
If brake drum will not rotate with applied torque of 180-204 lb-in (20-23 N•m), do Steps 5 - 7. If
brake drum rotates, go to Step 8.
5. Loosen screw (1) to maximum without disengaging from band assembly (4).
0409 00-2
TM 9-2350-247-20-3
ADJUST DRUM SAFETY BRAKE (M548A1) — Continued 0409 00
NOTE
Use helper when checking engine/PTO.
6. Start engine (see your -10) and engage PTO to transmission for 5 minutes to allow winch gears to break in.
7. Stop engine (see your -10). Repeat Step 4.
8. Install gasket (5), cover (6), six washers (7), and screws (8) on automatic brake case (9).
9. Install guard (10), plate (11), and two screws (12) on support (13).
10. Install two washers (14) and screws (15) to bottom of guard (10).
END OF TASK
0409 00-3/4 blank

TM 9-2350-247-20-3
REPLACE CLUTCH LEVER (M548A1) 0410 00

INITIAL SETUP:

Tools and Special Tools Battery negative lead disconnected (WP 0292 00)
Drum lock handle removed (WP 0411 00)
Personnel Required
Unit Mechanic
References
See your -10
REMOVAL
1. Remove screw (1) that secures clutch lever (2) to winch (3). Remove clutch lever from winch.
2. Remove two screws (4) and plate (5) that secure bracket (6) to winch (3). Remove bracket from winch.
0410 00-1
TM 9-2350-247-20-3
REPLACE CLUTCH LEVER (M548A1) — Continued 0410 00
INSTALLATION
1. Install bracket (1) on winch (2). Install plate (3) and two screws (4). Do not tighten screws until clutch is adjusted.
2. Install drum lock handle (5) on winch (2) (WP 0411 00).
3. Install clutch lever (6) on winch (2). Install screw (7). Make sure pin on clutch lever is in DISENGAGE slot of bracket
(1) (see your -10).
4. Move drum lock handle (5) to right to unlock drum (see your -10).
ADJUSTMENT
1. Move clutch lever (6) until clutch is bottomed on frame face, then move bracket (1) until outer side of slot is within .010
inch (.25 mm) of detente pin in lever.
2. Tighten two screws (4). Bend top corners of plate (3) across flats on screw heads.
END OF TASK
0410 00-2
TM 9-2350-247-20-3
REPLACE DRUM LOCK HANDLE (M548A1) 0411 00

INITIAL SETUP:

Unit See your -10
Equipment Condition
Materials/Parts
Cotter pin Engine stopped (see your -10)
Unit Mechanic Battery negative lead disconnected (WP 0292 00)
REMOVAL
1. Remove jam nut (1), nut (2), and washer (3) from poppet shaft (4).
2. Remove cotter pin (5), washer (6), and spring (7) from pin (8). Discard cotter pin.
3. Remove pin (8) from bracket (9). Remove drum lock handle (10) from bracket.
0411 00-1
TM 9-2350-247-20-3
REPLACE DRUM LOCK HANDLE (M548A1) — Continued 0411 00
INSTALLATION
1. Place drum lock handle (1) over poppet shaft (2) and under bracket (3). Install pin (4), spring (5), washer (6), and new
cotter pin (7).
2. Place washer (8) and nut (9) on poppet shaft (2). Do not tighten nut.
3. Move clutch lever (10) as far to right as it will go. Make sure detent pin in lever is seated in DISENGAGED slot of
bracket (3).
4. Unlock drum (see your -10). Turn winch drum by hand until poppet shaft (2) is seated in drum flange.
ADJUSTMENT
1. Hold nut (9) and install jam nut (11). Adjust nut (9) and nut (11) so that poppet shaft (2) is withdrawn 5/16 ± 1/16 inch
(7.6 ± 1.6 mm) from maximum inward travel when detent pin in lever is seated in hole on bracket.
END OF TASK
0411 00-2
TM 9-2350-247-20-3
REPLACE WINCH PROPELLER SHAFT (M548A1) 0412 00

INITIAL SETUP:

Unit See your -10
GAA grease (WP 0542 00, Item 14) Cab center floor plate removed (WP 0394 00)
Lock washer (8) Battery negative lead disconnected (WP 0292 00)
Seal Center seat raised (see your -10)
Personnel Required Left grille removed (WP 0390 00)
Unit Mechanic Air cleaner container with element removed
Helper (H) (WP 0152 00)
0412 00-1
TM 9-2350-247-20-3
REPLACE WINCH PROPELLER SHAFT (M548A1) — Continued 0412 00
REMOVAL
1. Remove eight nuts (1), lock washers (2), and four clamps (3). Have helper assist removing propeller shaft (4). Discard
lock washers.
0412 00-2
TM 9-2350-247-20-3
DISASSEMBLY
1. Remove one journal-and-bearing assembly (1) from each end of propeller shaft (2) by removing four retaining rings (3).
2. Unscrew cap (4) from sleeve yoke (5). Pull yoke (6) from sleeve yoke.
3. Pull seal (7) out of cap (4). Discard seal.
4. Remove three grease fittings (8) from sleeve yoke (5) and journal-and-bearing assemblies (1).
0412 00-3
TM 9-2350-247-20-3
ASSEMBLY
1. Place new seal (1) into cap (2). Place cap and seal on yoke (3).
CAUTION
Make sure yoke (4) and yoke (3) are installed with bearing journals in the same plane. Make
sure assembled shaft is not twisted. Propeller shaft can be damaged during operation if yokes
are not installed right.
2. Install yoke (3) into sleeve yoke (4).
3. Install cap (2) on sleeve yoke (4).
4. Install one journal-and-bearing assembly (5) in yoke (3). Install two retaining rings (6) to hold assembly in yoke.
5. Install one journal-and-bearing assembly (5) into sleeve yoke (4). Install two retaining rings (6) to hold assembly in
sleeve yoke.
6. Install one grease fitting (7) in front and rear journal-and-bearing assemblies (5) and one grease fitting in sleeve yoke (4).
7. Lubricate two journal-and-bearing assemblies (5) with grease.
0412 00-4
TM 9-2350-247-20-3
INSTALLATION
1. Place assembled propeller shaft (1) between yoke (2) on power takeoff (3) and yoke (4) on transfer gearcase (5).
2. Place two clamps (6) over yoke (2). Secure each clamp with two new lock washers (7) and two nuts (8). Tighten nuts to
14-17 lb-ft (19-23 N•m) torque.
3. Place two clamps (6) over yoke (4). Secure each clamp with two new lock washers (7) and nuts (8). Tighten nuts to
14-17 lb-ft (19-23 N•m) torque.
2. Install air cleaner container with element (WP 0152 00).
3. Install left grille (WP 0390 00).
END OF TASK
0412 00-5/6 blank

TM 9-2350-247-20-3
REPLACE WINCH TRANSFER GEARCASE (M548A1) 0413 00


Cleaning and Inspection (page 0413 00-2).
INITIAL SETUP:

Unit See your -10
Materials/Parts
Cotter pin
Lock nut Cab center floor plate removed (WP 0394 00)
Screw Battery negative lead disconnected (WP 0292 00)
Personnel Required Winch propeller shaft disconnected at transfer gearcase
REMOVAL
1. Remove lock nut (1), washer (2), two bushings (3), and gearcase (4) from stud (5) and winch input shaft (6). Discard
lock nut.
0413 00-1
TM 9-2350-247-20-3
REPLACE WINCH TRANSFER GEARCASE (M548A1) — Continued 0413 00
2. If gearcase cannot be moved, fabricate gearcase removal tool (7) from 3/4-10 inch x 6 inch bolt. Cut head off bolt. Saw
or file a 0.06-inch screwdriver slot in unthreaded end.
3. Remove screw (8) from gearcase (4) and insert gearcase removal tool (7). Turn until gearcase comes off winch input
shaft (6).
4. Remove cotter pin (9) from pin (10). Pull pin (10) from yoke (11). Discard cotter pin.
5. Remove two cotter pins (12) from shear pin (13). Pull shear pin out of yoke (11). Discard cotter pins.
6. Pull yoke (11) from gearcase output shaft (14).
CLEANING AND INSPECTION
1. Clean and service gearcase (WP 0128 00).
2. Check nut and stud. Replace nut that has stripped threads. Notify your supervisor if stud is cracked or stripped.
3. Check gearcase. Replace gearcase that leaks or is cracked.
4. Check bushings. Replace bushing that is worn or cracked.
0413 00-2
TM 9-2350-247-20-3
REPLACE WINCH TRANSFER GEARCASE (M548A1) — Continued 0413 00
INSTALLATION
CAUTION
Bushings used to mount the gearcase are tapered. They must be installed right to prevent
bushing deformation and lack of shock absorption. Install bushings as shown with tapered side
toward gearcase.
1. Place bushing (1) on stud (2) in carrier bulkhead.
2. Position gearcase (3) on carrier bulkhead. Align bushing (1) and stud (2) in gearcase mounting hole and winch output
shaft (4) with spline in gearcase. Seat gearcase firmly against stud and shaft.
3. Install bushing (5) on stud (2). Install washer (6) and new lock nut (7).
4. Place yoke (8) on gearcase output shaft (9). Secure with shear pin (10) and two new cotter pins (11).
5. Install pin (12) and new cotter pin (13) in yoke (8).
6. Install screw (14) replaced by gearcase removal tool during removal.
1. Connect winch propeller shaft at transfer gearcase (WP 0412 00).
END OF TASK
0413 00-3/4 blank

TM 9-2350-247-20-3
REPLACE WINCH POWER TAKEOFF CONTROL (M548A1) 0414 00


INITIAL SETUP:

Unit See your -10

Equipment Condition
Torque Wrench (WP 0541 00, Item 67) Carrier blocked (see your -10)
Left grille removed (WP 0390 00)
Materials/Parts
Center seat raised (see your -10)
GAA grease (WP 0542 00, Item 14)
Cab center floor plate removed (WP 0394 00)
Grommet
Power plant rear access covers/door removed
Personnel Required (see your -10)
REMOVAL
1. Loosen setscrew (1) that secures outer control cable (2) to power takeoff actuating lever (3).
2. Remove jam nut (4), nut (5), and bracket (6) that secure outer control cable (2) to screw (7). Pull control cable from
bracket.
3. Remove screw (8), washer (9), and clamp (10) that secure outer control cable (2) to power plant compartment.
0414 00-1
TM 9-2350-247-20-3
REPLACE WINCH POWER TAKEOFF CONTROL (M548A1) — Continued 0414 00
4. Remove screw (11), washer (12), and clamp (13) that secure outer control cable (2) to bulkhead inside cab.
5. Loosen nut (14) that secures inner control cable (15) to range selector housing (16) inside cab. Pull inner control cable
out of housing. Push outer control cable (2) through opening in housing. Remove jam nut (17) and washer (18).
6. Remove grommet (19) from cab floor. Discard grommet.
CLEANING
1. Clean all parts.
2. Check outer control cable casing. Replace outer control cable that is not flexible or if it is cracked, broken, or cut.
3. Lubricate outer control cable with grease (WP 0128 00).
4. Check screws, washers, and clamps. Replace parts that have stripped threads or are cracked or deformed.
0414 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Thread outer control cable (1) through jam nut (2), washer (3), and opening in range selector housing (4). Install jam nut
on control cable a few turns but do not tighten.
2. Install new grommet (6) on cab floor. Thread outer control cable (1) through grommet.
3. Install clamp (7), washer (8), and screw (9) to secure outer control cable (1) to bulkhead inside cab.
0414 00-3
TM 9-2350-247-20-3
4. Thread outer control cable (1) through power plant compartment and bulkhead. Secure control cable to compartment
floor with clamp (10), washer (11), and screw (12).
5. Place range selector in NEUTRAL (see your -10).
6. Push inner control cable (13) through range selector housing (4) and winch control handle (14). Push winch control
handle against range selector housing and turn handle a quarter turn to lock it. Tighten nut (2).
7. Push power takeoff actuating lever (15) as far forward as it will go. Bend outer control cable (1) so you can put end
through setscrew (16). Do not tighten setscrew.
8. Install bracket (17) and nut (18) on screw (19). Tighten nut. Install and tighten jam nut (20).
9. Tighten setscrew (16).
FOLLOW THROUGH STEPS

5. Install power plant rear access covers/door (see your -10). Install power plant rear access covers/door (see your -10).
END OF TASK
0414 00-4
TM 9-2350-247-20-3
REPLACE POWER TAKEOFF (M548A1) 0415 00

INITIAL SETUP:

Unit See your -10
Equipment Condition
General Mechanic’s Tool Kit (WP 0541 00, Item 57) Carrier blocked (see your -10)
Socket Wrench Set (WP 0541 00, Item 63) Battery negative lead disconnected (WP 0292 00)
Torque Wrench (WP 0541 00, Item 67) Winch propeller shaft at power takeoff disconnected
Materials/Parts (WP 0412 00)
Control cable disconnected from power takeoff
Gasket (WP 0414 00)
Personnel Required Power plant rear access door removed (see your -10)
Unit Mechanic Left grille removed (WP 0390 00)
Air filter canister and element removed (WP 0152 00)
0415 00-1
TM 9-2350-247-20-3
REPLACE POWER TAKEOFF (M548A1) — Continued 0415 00
REMOVAL
2. Remove six screws (1) and washers (2) from power takeoff mounting flange (3). Pull power takeoff (4) from
transmission.
3. Remove and discard gasket (5).
4. Remove key (6) and setscrew (7) from yoke (8). Pull yoke from power takeoff shaft.
0415 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install yoke (1) on power takeoff shaft. Secure yoke to shaft by installing setscrew (2) and key (3).
2. Place one 0.020 inch (0.5 mm) new gasket (4) on power takeoff mounting flange (5) of power takeoff (6).
3. Place power takeoff (6) on transmission. Place six washers (7) on screws (8). Install screws through power takeoff into
transmission. Tighten screws to 216-264 lb-in (26-32 N•m) torque.
4. Connect winch propeller shaft to power takeoff (WP 0412 00).

5. Connect power takeoff control to power takeoff (WP 0414 00).
8. Place winch drum lever in DISENGAGE (see your -10).
9. Check power takeoff for operation by pulling winch control handle in cab (see your -10) and listening to power takeoff.
CAUTION
Two gaskets are supplied with power takeoff: one is 0.020 inch (0.5 mm) thick, the other is 0.010
inch (0.25 mm) thick. The power takeoff can be damaged during operation if the wrong gasket
is installed.
10. A whining sound from power takeoff means an incorrect backlash between power takeoff and gear in transmission. Add
0.010 inch (0.25 mm) gaskets, as needed, to stop whining sound.
0415 00-3
TM 9-2350-247-20-3
NOTE
Notify your supervisor if changing gaskets does not stop whining or vibration.
11. A badly vibrating power takeoff means gear backlash is too tight. Remove two 0.010 inch (0.25 mm) gaskets to stop
vibration. Add one gasket if needed.
1. Install air filter container and element (WP 0152 00).
3. Install power plant rear access door (see your -10).
END OF TASK
0415 00-4
TM 9-2350-247-20-3
REPLACE WIRE ROPE, HOOK, AND CHAIN (M548A1) 0416 00

INITIAL SETUP:

Unit See your -10
FM 9-43-2
Tools and Special Tools FM 5-125
Equipment Condition
Materials/Parts Engine stopped/shutdown (see your -10)
Wire rope grease (WP 0542 00, Item 46) Carrier blocked (see your -10)
Rod, 1/8 inch (3 mm) Battery negative lead(s) disconnected (WP 0292 00)
Used engine oil (see your LO)
Personnel Required
Unit Mechanic
Helper (H)
0416 00-1
Change 1
TM 9-2350-247-20-3
REPLACE WIRE ROPE, HOOK, AND CHAIN (M548A1) — Continued 0416 00
REMOVAL
WARNING
Wear leather gloves when handling wire rope. Broken wires can rip your hands open.
1. Use helper to reel out wire rope (1) as far as it will go (see your -10).
2. Loosen screw (2). Pull wire rope from drum.
3. Remove nut (3) and bolt (4) from clevis (5). Remove hook and chain (6) from clevis.
CLEANING
1. Check wire rope. See your FM 9-43-2 and FM 5-125 for wire rope wear criteria. Replace rope assembly if wires are
broken or badly worn. Replace clevis or pin that is damaged.
2. Insert a 1/8 inch (3 mm) rod into inspection hole (7) in clevis. Replace wire rope assembly if rod can be inserted more
than 3/4 inch (19 mm).
3. Check chain. Replace chain assembly if chain or hook has cracks.
0416 00-2
Change 1
TM 9-2350-247-20-3
REPLACE WIRE ROPE, HOOK, AND CHAIN (M548A1) — Continued 0416 00
INSTALLATION
1. Install bolt (1) through clevis (2) and hook and chain (3). Secure with nut (4).
2. Turn winch drum until mounting hole in drum is on top.
WARNING
Wear leather gloves when handling wire rope. Broken wires can rip your hands open.
3. Push wire rope (5) through mounting hole as far as it will go. Install and tighten screw (6).
4. Lube wire rope (see your PMCS).
1. Connect battery negative lead(s) (WP 0292 00).
3. Reel in wire rope (see your -10). Have helper assist.
END OF TASK
0416 00-3/4 blank

Change 1
TM 9-2350-247-20-3
CHAPTER 20
FOR HULL ACCESSORY ITEMS
WORK PACKAGE INDEX

Title Sequence No.
REPLACE CARGO COMPARTMENT COVER.............................................................................................................0417 00

REPLACE CAB COVER AND FRAMES........................................................................................................................0418 00
REPLACE FRONT STEP..................................................................................................................................................0419 00
REPLACE WINDSHIELD WIPER MOTOR...................................................................................................................0420 00
REPLACE WINDSHIELD WIPER LINKAGE................................................................................................................0421 00
REPLACE WINDSHIELD WIPER ARM AND BLADE................................................................................................0422 00
DELETED..........................................................................................................................................................................0423 00
REPLACE BILGE PUMP.................................................................................................................................................0424 00
REPLACE BILGE PUMP DISCHARGE TUBES AND HOSES (M548A1)..................................................................0425 00
REPLACE BILGE PUMP DISCHARGE TUBES AND HOSES (M548A3)..................................................................0426 00
SERVICE/REPAIR/ADJUST VEHICLE COMPARTMENT HEATER...........................................................................0427 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY AND MOUNTING
BRACKETS (M548A3)...........................................................................................................................................0428 00
SERVICE VEHICLE COMPARTMENT HEATER FUEL PUMP...................................................................................0429 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY FUEL PUMP (M548A3)..........................................0430 00
REPLACE VEHICLE COMPARTMENT HEATER CONTROL BOX...........................................................................0431 00
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER, HOSES, AND FANS
(M548A3).................................................................................................................................................................0432 00
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN TOGGLE
SWITCHES/IDENTIFICATION PLATE.................................................................................................................0433 00
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN WIRING HARNESS.....................................0434 00
REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS (M548A3)...................................................0435 00
SERVICE PERSONNEL HEATER FUEL FILTER .........................................................................................................0436 00
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST METAL HOSE ASSEMBLY
(M548A3).................................................................................................................................................................0437 00
REPLACE VEHICLE COMPARTMENT HEATER AIR INLET DUCTS (M548A3)....................................................0438 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES TO FUEL/SEPARATOR
FILTER (M548A3)...................................................................................................................................................0439 00
REPLACE PLATES, STENCILS, DECALS, RUBBER PADS, AND STRAPS.............................................................0440 00
DATA PLATE, MARKER, AND DECAL CHART (M548A1)........................................................................................0441 00
DATA PLATE, MARKER, AND DECAL CHART (M548A3)........................................................................................0442 00
Change 1
TM 9-2350-247-20-3
REPLACE CARGO COMPARTMENT COVER 0417 00

INITIAL SETUP:

Unit Unit Mechanic

0417 00-1
TM 9-2350-247-20-3
REPLACE CARGO COMPARTMENT COVER — Continued 0417 00
REMOVAL
1. Disengage four web straps (1) that secure corners of cargo compartment cover (2).
2. Loosen four outside tie-down ropes (3) on sides and rear of carrier. Disengage ropes from outside tie-down cleats (4).
3. Loosen inside tie-down rope (5). Disengage rope from inside tie-down cleats (6).
4. Disengage six web straps (1) that secure front and rear closure flaps in closed position.
5. Untie nine cover tie ropes (7) that secure cargo compartment cover (2) to bow (8) and bow (9) inside carrier.
0417 00-2
TM 9-2350-247-20-3
6. Remove cargo compartment cover (1) from carrier.

7. Remove escape hatch cover (2) from hatch cover frame (3).
8. Remove 15 screws (4), 14 washers (5), retainer (6), 15 lock washers (7), and 15 nuts (8) that secure hatch cover frame (3)
and gasket (9) to cargo compartment cover (1) and clamping ring (10). Discard lock washers.
9. Remove four bows (11) and eight pads (12) from carrier.
10. Remove 8 screws (13) and 16 washers (14) that secure 2 bows (15) to carrier. Remove bows and 4 pads (16).
0417 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Place 4 bow pads (1) and 2 bows (2) on carrier. Secure with 16 washers (3) and 8 screws (4).
2. Install eight pads (5) and four bows (6) on carrier.
3. Install clamping ring (7) in cargo compartment cover (8). Secure to gasket (9) and hatch cover frame (10) with 15 screws
(11), 14 washers (12), retainer (13), 15 new lock washers (14), and 15 nuts (15). Tighten nuts to 20-25 lb-in (27-34 N•m)
torque.
4. Install escape hatch cover (16) on hatch cover frame (10).
0417 00-4
TM 9-2350-247-20-3
5. Install cargo compartment cover (1) over bow (2) and bow (3) with escape hatch at right rear.
6. Attach cargo compartment cover (1) to two bows (2) and two bows (3) with nine cover tie ropes (4) inside carrier.
7. Fasten three web straps (5) to secure front closure flaps in closed position.
8. Install inside tie-down rope (6) under inside tie-down cleats (7). Tighten ropes until front flaps of cargo compartment
cover (1) are positioned right. Tie rope ends securely. Stow ends of rope by pulling ends between secured portion of rope
and power plant compartment rear bulkhead.
0417 00-5
TM 9-2350-247-20-3
9. Make sure cargo compartment cover (1) is positioned right and stretched smoothly over bows (2) and bows (3). Fasten
three web straps (5) to secure rear closure flaps in closed position.
10. Install four outside tie-down ropes (8) under outside tie-down cleats (9). Tie rope ends securely. Stow ends by pulling
between secured portion of rope and hull of carrier.
NOTE
Secure sides of cargo compartment cover first, working from front to rear; then secure near
flaps. Make sure uniform tension is applied to all parts of cover and that cover is positioned
right and is as smooth as possible.
11. Fasten four web straps (5) to secure rear corners of cargo compartment cover (1).
END OF TASK
0417 00-6
TM 9-2350-247-20-3
REPLACE CAB COVER AND FRAMES 0418 00

INITIAL SETUP:

Unit Unit Mechanic
Socket Wrench Set (WP 0541 00, Item 63) See your -10
Materials/Parts
Equipment Condition
Lock nut (15)
Lock nut (2) Machine gun mount kit removed (WP 0513 00),
Lock washers (14) (WP 0514 00), or (WP 0515 00)
0418 00-1
TM 9-2350-247-20-3
REPLACE CAB COVER AND FRAMES — Continued 0418 00
REMOVAL
1. Remove machine gun hatch cover (1) from cab cover (2).
2. Remove 15 lock nuts (3), washers (4), screws (5), 14 lock washers (6), and hatch cover retainer (7) that secure ring (8)
and gasket (9) to cover (2) and ring (10). Discard lock nuts and lock washers.
3. Disengage 12 cover snaps (11) from snap studs (12) on each side of cab cover (2).
4. Disengage tie-down rope (13) from tie-down cleats (14) at rear of cab.
5. Pull cab cover (2) forward and let cover hang down in front of carrier.
0418 00-2
TM 9-2350-247-20-3
6. Pull cab cover (1) to side to disengage rope retainer (2) from front mounting frame (3).
7. Remove two lock nuts (4), four washers (5), and two screws (6) that secure cab bow (7) to two window frames (8).
Remove bow. Discard lock nuts.
8. Remove two lock nuts (9), spacers (10), screws (11), and washers (12) that secure two window frames (8) to hull.
Discard lock nuts.
0418 00-3
TM 9-2350-247-20-3
9. Remove four lock nuts (13), eight washers (14), and four screws (15) that secure two window frames (8) to front
mounting frame (3). Remove frames. Discard lock nuts.
10. Remove 8 lock nuts (16), 16 washers (17), 8 screws (18), 16 grommets (19), and 8 spacers (20). Remove front mounting
frame (3), mounting frame seal (21), and two frame end seals (22) from cab windshield (23). Discard lock nuts.
0418 00-4
TM 9-2350-247-20-3
INSTALLATION
1. Place mounting frame seal (1), two frame end seals (2), and front mounting frame (3) on cab windshield (4). Secure
seals and frame with 8 spacers (5), 16 grommets (6), washers (7), 8 screws (8), and new lock nuts (9).
2. Place two window frames (10) on carrier. Secure frames to front mounting frame (3) with eight washers (11), four
screws (12), and four new lock nuts (13).
0418 00-5
TM 9-2350-247-20-3
3. Secure two window frames (10) to hull with two washers (14), screws (15), spacers (16), and new lock nuts (17).
4. Install cab bow (18) on two window frames (10). Secure bow to frames with four washers (19), two screws (20), and
new lock nuts (21).
5. Place cab cover (22) with rope retainer (23) at top and inside facing forward. Align retainer with groove in front
mounting frame (3). Pull cover across front of carrier until cover is positioned, right for installation.
0418 00-6
TM 9-2350-247-20-3
6. Pull cab cover (1) back over bow (2).

7. Secure 12 cover snaps (3) on snap studs (4) on each side of cab over (1) starting at front.
8. Secure tie-down rope (5) under tie-down cleats (6) at rear of cab.
9. Place retaining ring (7) with gasket (8) on cable cover (1). Secure with ring (9), 15 screws (10), washers (11), 14 new
lock washers (12), hatch cover retainer (13) and 15 nuts (14). Tighten nuts to 20-25 lb-in (27-40 N•m) torque.
10. Install machine gun hatch cover (15) on cab cover (1).
0418 00-7
TM 9-2350-247-20-3
1. Install machine gun mount kit (WP 0513 00), (WP 0514 00), or (WP 0515 00).
END OF TASK
0418 00-8
TM 9-2350-247-20-3
REPLACE FRONT STEP 0419 00

INITIAL SETUP:

Unit See your -10
REMOVAL
1. Remove four screws (1) and washers (2) from front step (3).
2. Remove front step (3) from hull.
3. Check front step. Straighten bends and dents. Weld cracks (WP 0406 00).
INSTALLATION
1. Place front step (3) on hull. Secure with four screws (1) and washers (2).
END OF TASK
0419 00-1/2 blank

TM 9-2350-247-20-3
REPLACE WINDSHIELD WIPER MOTOR 0420 00

INITIAL SETUP:

Unit Unit Mechanic


Locknut Engine stopped (see your -10)
Lockwasher Carrier blocked (see your -10)
Lockwasher Battery negative lead(s) disconnected (WP 0292 00)
Lockwasher (6)
REMOVAL
1. Pull nipple (1) away from screw (2). Remove screw (2), two lockwashers (3), lead (4), and capacitor lead (5) from
windshield wiper motor (6). Discard lockwashers.
2. Remove screw (7) and capacitor (8) from weldnut (9).
3. Remove tension clip (10), washer (11), and link (12) from pivot post on windshield wiper motor (6).
4. Remove three screws (13) and six lockwashers (14) that secure windshield wiper motor (6) to bracket (15). Remove
locknut (16), screw (17), and clamp (18). Discard locknut and lockwashers.
5. Lift windshield wiper motor (6) from carrier.
0420 00-1
Change 1
TM 9-2350-247-20-3
REPLACE WINDSHIELD WIPER MOTOR — Continued 0420 00
INSTALLATION
1. Place pivot post of windshield wiper motor (1) through hole in bracket (2).
2. Install three screws (3) and six new lockwashers (4) to secure windshield wiper motor (1) to bracket (2). Place washers
on each side of bracket. Do not tighten screws.
3. Slide clamp (5) over end of windshield wiper motor (1). Secure clamp to bracket with screw (6) and new locknut (7).
Tighten all screws.
4. Place end of link (8) on pivot post of windshield wiper motor (1). Install washer (9) and clip (10) on pivot post.
5. Install capacitor (11) on weldnut (12) with screw (13).
6. Pull nipple (14) back and install new lockwasher (15), lead (16), new lockwasher (15), and capacitor lead (17) on
screw (18). Install screw in windshield wiper motor (1).
2. Check windshield wiper motor for proper operation.
3. Turn windshield wiper switch OFF (see your -10).
END OF TASK
0420 00-2
Change 1
TM 9-2350-247-20-3
REPLACE WINDSHIELD WIPER LINKAGE 0421 00

INITIAL SETUP:

Unit See your -10
Materials/Parts
Battery ground lead(s) disconnected (WP 0292 00)
Locknut (3)
Lockwasher
Personnel Required
Unit Mechanic
0421 00-1
Change 1
TM 9-2350-247-20-3
REPLACE WINDSHIELD WIPER LINKAGE — Continued 0421 00
REMOVAL
1. Remove two clips (1) and washers (2) from link (3). Pull link from motor (4) and pivot (5).
2. Remove two clips (1) and washers (2) from link (6). Pull link from pivot (7) and pivot (8). Remove spacer (9) from
pivot (8).
3. Pull link (10) from pivot (5) and pivot (7).
NOTE
There are three arm and blade assemblies and tapered bushings, only one is shown. All are
removed in the same way.
4. Remove nut (11), lockwasher (12), and arm and blade assembly (13) from pivot (8). Remove tapered bushing (14) from
pivot (8). Remove arm and blade assemblies from pivots (5) and (7) the same way. Discard lockwasher.
5. Remove locknut (15) and screw (16) from pivot (8). Pull pivot (8) with spacer (9) from carrier. Remove pivot (5)
and pivot (7) the same way. Discard locknut.
0421 00-2
Change 1
TM 9-2350-247-20-3
INSTALLATION
1. Place pivots (5), (7), and (8) into carrier hull. Secure each pivot with screw (16) and new locknut (15).
NOTE
There are three arm and blade assemblies and tapered bushings, only one is shown. All are
installed in the same way.
2. Place tapered bushings (14) on pivots (5), (7), and (8). Place arm and blade assembly (13) on pivots. Make sure arm
mates with tapered bushing.
3. Secure arm and blade assembly (13) with new lockwasher (12) and nut (11) on pivot (5). Install pivot (7), pivot (8),
and arm and blade assemblies the same way.
CAUTION
Install links with flat side toward pivot. Linkage could be damaged during operation if open
side of link is toward pivot.
4. Place link (10) on pivot (5) and pivot (7).

5. Place spacer (9) on pivot (8). Place link (6) on pivot (8) and over link (10) on pivot (7). Install two washers (2) and
clips (1) on link (6).
6. Place link (3) on motor (4) and pivot (5). Install two washers (2) and clips (1) on link.
0421 00-3
Change 1
TM 9-2350-247-20-3
1. Connect battery ground lead(s) (WP 0292 00).
2. Check operation of windshield wiper linkage.
END OF TASK
0421 00-4
Change 1
TM 9-2350-247-20-3
REPLACE WINDSHIELD WIPER ARM AND BLADE 0422 00

INITIAL SETUP:

Unit See your -10

Unit Mechanic Battery ground lead(s) disconnected (WP 0292 00)
REMOVAL
NOTE
All three windshield wiper arm and blade assemblies are removed, installed, and adjusted the
same way.
1. Remove nut (1), washer (2), windshield wiper arm (3), and knurled nut (6) from pivot (4). Pull arm from pivot.
2. To pull blade (5) from windshield wiper arm (3), grasp blade at point where it mates with arm and pull blade straight
away from arm.
0422 00-1
TM 9-2350-247-20-3
REPLACE WINDSHIELD WIPER ARM AND BLADE — Continued 0422 00
INSTALLATION
1. Place knurled nut (6) on pivot (4).
2. Install blade (5) on windshield wiper arm (3). Install windshield wiper arm on pivot (4). Make sure windshield wiper
arm mates with knurled nut (6).
0422 00-2
TM 9-2350-247-20-3
REPLACE WINDSHIELD WIPER ARM AND BLADE — Continued 0422 00
ADJUSTMENT
1. Adjust windshield wiper arm (3) by moving it around knurled nut (6) until both ends of blade (5) are equally distant from
edge of windshield.
2. Install washer (2) and nut (1).
1. Connect battery ground lead(s) (WP 0292 00).
END OF TASK
0422 00-3/4 blank

TM 9-2350-247-20-3
REPLACE BILGE PUMP 0424 00

INITIAL SETUP:

Unit See your -10

Cab center floor plates raised (WP 0394 00) or
Key washer (3)
(WP 0395 00)
Lock washer (5)
Right seat removed (WP 0400 00)
Lock washer (2)
Cab personnel seat raised (see your -10)
Personnel Required Differential to final drive shaft removed (WP 0334 00) or
0424 00-1
TM 9-2350-247-20-3
REPLACE BILGE PUMP — Continued 0424 00
REMOVAL
NOTE
Bilge pumps are removed and installed the same way in M548A1 and M548A3. Bilge pumps are
located in different locations. Both locations are shown. There is only one bilge pump in each
carrier.
1. Disconnect circuit 452 lead (1) from bilge pump (2).
2. Loosen two clamps (3). Slide hose (4) with two clamps from bilge pump (2) onto pump outlet tube (5).
3. Remove two screws (6) and key washers (7) that secure end strap (8) to two hull weld nuts (9). Remove strap. Discard
key washers.
4. Remove two screws (10), key washer (11), and three lock washers (12) that secure cross strap (13) and negative lead (14)
to hull weld nuts (9). Discard key and lock washers.
5. Remove cross strap (13) and bilge pump (2).
0424 00-2
TM 9-2350-247-20-3
6. Remove two screws (1) and lock washers (2) that secure screen (3) to bilge pump (4). Discard lock washers.
7. Separate screen (3) from bilge pump (4).
8. Remove screw (5) and two lock washers (6) that secure negative lead (7) to bilge pump (4). Remove negative lead.
Discard lock washers.
9. Remove adapter (8) from bilge pump (4).
CLEANING
1. Clean 1/8 inch (2 mm) air bleed hole (9).
2. Clean the bottom of the hull. Remove all sludge, oil, dirt or other debris.
0424 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Place screen (3) on bilge pump (4). Secure with two new lock washers (2) and screws (1).
NOTE
Install one lock washer (6) between negative lead and pump and another between negative lead
and screw head.
2. Install negative lead (7) on bilge pump (4) with screw (5) and two new lock washers (6).
3. Install adapter (8) on bilge pump (4).
0424 00-4
TM 9-2350-247-20-3
NOTE
One lock washer (6) is installed between strap (2) and hull weld nut (3), one between strap and
negative lead (7), and one between negative lead and screw (8).
4. Place bilge pump (1) and cross strap (2) on hull (3). Secure cross strap to hull with new key washer (4), screw (5), three
new lock washers (6), negative lead (7), and screw (8).
5. Bend tabs of key washer (4) to secure screw (5).
6. Place end strap (9) on bilge pump (1) and two hull weld nuts (3). Secure strap with two new key washers (10) and
screws (11).
0424 00-5
TM 9-2350-247-20-3
7. Bend tabs of two key washers (10) to secure screws (11).

8. Slide hose (12) with two clamps (13) towards end of pump outlet tube (14) and onto adapter (16). Tighten two clamps.
9. Connect circuit 452 lead (15) to bilge pump (1).
10. Turn MASTER SWITCH ON (see your -10).

11. Turn bilge pump on and put your hand over outlet. If you feel air, pump is working.
1. Install differential to final drive shaft (WP 0334 00) or (WP 0335 00).
2. Lower cab center floor plates (WP 0394 00) or (WP 0395 00).
3. Lower cab personnel seat (see your -10).
4. Install right seat (WP 0400 00).
END OF TASK
0424 00-6
TM 9-2350-247-20-3
REPLACE BILGE PUMP DISCHARGE TUBES AND HOSES (M548A1) 0425 00


INITIAL SETUP:

Unit See your -10

Right seat removed (WP 0400 00)
Unit Mechanic
Cab center floor plates raised (WP 0394 00)
REMOVAL
NOTE
Remove only those tubes and hoses to be replaced. Remove hoses and tubes with clamps
attached. Put clamps on replacement hoses and tubes before installation.
1. Remove two screws (1), washers (2), and clamps (3) from tube (4).
2. Loosen four clamps (5) that secure two hoses (6) to tube (4). Separate tube from hoses. Remove hoses from tube (7) and
bilge pump (8).
0425 00-1
TM 9-2350-247-20-3
REPLACE BILGE PUMP DISCHARGE TUBES AND HOSES (M548A1) — Continued 0425 00
INSTALLATION
1. Install two hoses (6) on each end of tube (4). Connect hoses to tube (7) and bilge pump (8). Tighten four clamps (5).
2. Install two clamps (3) on tube (4) and secure to hull with two screws (1) and washers (2).
1. Lower cab center floor plates (WP 0394 00).
2. Install right seat (WP 0400 00).
END OF TASK
0425 00-2
TM 9-2350-247-20-3
REPLACE BILGE PUMP DISCHARGE TUBES AND HOSES (M548A3) 0426 00

INITIAL SETUP:

Unit See your -10

Both battery negative leads disconnected (WP 0292 00)
Lock washer (3) Center seat raised (see your -10)
Personnel Required Cab center floor plates and seat support removed
Hull bottom access cover removed (WP 0383 00)
0426 00-1
TM 9-2350-247-20-3
REMOVAL
NOTE
Remove only those hoses and tubes to be replaced. Remove hoses and tubes with clamps
attached. Put clamps on replacement hoses and tubes before installation.
1. Remove two clamps (1) and hose (2) from outlet tube (3).
2. Remove two screws (4), lock washers (5), and clamps (6) securing outlet tube (3) to hull. Discard lock washers.
3. Remove two clamps (7) and hose (8) from outlet tube (3) and tube (9). Remove outlet tube from carrier bottom plate.
4. Remove screw (10), lock washer (11), and clamp (12) from tube (9). Discard lock washer.
5. Remove two clamps (13) and hose (14) from tube (9) and adapter (15). Remove tube, hose, clamps, and attaching
hardware from carrier.
0426 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install hose (1) and two clamps (2) on adapter (3) and tube (4). Tighten clamps.
2. Install tube (4) on carrier bottom plate with clamp (5), new lock washer (6), and screw (7).
3. Install outlet tube (8) on tube (4) and hose (9) with two clamps (10).
4. Install hose (11) and two clamps (12) on outlet tube (8).
5. Install outlet tube (8) on hull with two clamps (13), new lock washers (14), and screws (15).
1. Install cab center floor plates and seat support (WP 0395 00).
3. Install hull bottom access cover (WP 0383 00).
4. Connect both battery negative leads (WP 0292 00).
END OF TASK
0426 00-3/4 blank

TM 9-2350-247-20-3
SERVICE/REPAIR/ADJUST VEHICLE COMPARTMENT HEATER 0427 00

Servicing (page 0427 00-1).
INITIAL SETUP:

Unit See your -10
TM-9-2540-205-24&P
SERVICING
1. See TM-9-2540-205-24&P for all repairs and adjustments to the vehicle compartment heater.
END OF TASK
0427 00-1/2 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY AND 0428 00

MOUNTING BRACKETS (M548A3)
INITIAL SETUP:

Unit See your -10
TM 9-2540-207-14&P
Materials/Parts
Wiping rag (WP 0542 00, Item 45) Both battery negative leads disconnected (WP 0292 00)
Lockwasher (8) Front access cover removed (WP 0391 00)
Lockwasher (5)
Personnel Required
Unit Mechanic
Helper (H)
REMOVAL
WARNING
Sparks can cause fire or explosion. Fuel can catch fire and burn you. Do not smoke. Wipe
up any spilled fuel immediately.
NOTE
Fuel inlet hose will allow fuel to leak when disconnected. Be prepared to immediately plug hose
when it is disconnected. Use wiping rag to wipe up any excess fuel.
0428 00-1
Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY AND MOUNTING 0428 00

BRACKETS (M548A3) — Continued
1. Drain fuel filter bowl. See your -10.

2. Disconnect fuel hose (1) from fuel filter elbow (7).
3. Disconnect supply fuel hose (5) from fuel filter elbow (4).
4. Loosen clamp (3) and remove bracket with fuel filter (6) from heater (2).
NOTE
Do Step 5 only if replacing fuel filter.
5. Remove two screws (1), lockwashers (5), washers (4), nuts (6), and fuel filter (2) from bracket (3). Discard lockwashers.
0428 00-2
Change 1
TM 9-2350-247-20-3

6. Loosen seven clamp halves (3) on plenum sleeve (2) and heater (4).
7. Loosen clamp (10) securing air inlet duct (11) to heater air inlet (12). Remove two screws (7), lockwashers (8), and
washers (9) securing air inlet duct to bulkhead. Discard lockwashers.
8. Loosen two clamps (13) securing exhaust duct (14) to heater (4) and pipe (1).
9. Disconnect wiring harness (6) from heater receptacle (5).
10. Have helper support heater (4). Move heater around to loosen and remove air inlet duct (11) from heater air inlet (12)
and bulkhead. Remove air inlet duct from carrier.
11. Have helper support heater (4). Remove exhaust duct (14) from heater and pipe (1). Remove exhaust duct from carrier.
0428 00-3
Change 1
TM 9-2350-247-20-3

12. Have helper support and rotate heater (1). Remove fuel inlet hose (2) from heater elbow (3). Plug fuel hose.
NOTE
Do Step 13 if removing heater Model A-20, MIL-PRF-62550/2A.
13. Remove two screws (10), lockwashers (11), ground strap (12), and clamp (13) from heater (1) and weldnut. Discard
lockwashers.
14. Have helper support heater (1). Disconnect four clamp halves (4). Slide heater from plenum sleeve (5). Remove heater
from carrier. Remove sleeve from heater plenum (6) and four clamp halves and sleeve from carrier.
0428 00-4
Change 1
TM 9-2350-247-20-3

NOTE
Do Step 15 and Step 16 only if clamps or mounting brackets are being replaced.
15. Remove four clamp halves (4) from two mounting brackets (7).
16. Remove four screws (8), five lockwashers (9), and two mounting brackets (7) from bulkhead. Note location of fifth
lockwasher. Discard lockwashers.
0428 00-5
Change 1
TM 9-2350-247-20-3

INSTALLATION
NOTE
Do Step 1 and Step 2 only if clamps or mounting brackets were removed for replacement.
1. Install two mounting brackets (7), five new lockwashers (9), and four screws (8) on bulkhead.
2. Install four clamp halves (4) on two mounting brackets (7).
3. Install plenum sleeve (5) and four clamp halves (4) on heater plenum (6). Do not tighten clamps.
NOTE
Refer to TM-9-2540-207-14&P for the mandatory replacement of the vent outlet seal (10)
on the heater (1).
4. Place heater (1) in plenum sleeve (5) and four clamp halves (4). Have helper assist.
0428 00-6
Change 1
TM 9-2350-247-20-3

NOTE
Do Step 5 if installing heater Model A-20, MIL-PRF-62550/2A.
5. Install ground strap (13), two new lockwashers (12), two screws (11), and clamp (14) to heater (1) and weldnut.
NOTE
Fuel inlet hose will allow fuel to leak when plug is removed. Be prepared to immediately connect
hose to heater elbow. Use wiping rag to wipe up any excess fuel.
6. Have helper support and rotate heater (1). Remove plug from fuel inlet hose (2). Install fuel inlet hose on heater
elbow (3).
0428 00-7
Change 1
TM 9-2350-247-20-3

7. Place two clamps (13) on exhaust duct (14). Install exhaust duct on heater (4) and pipe (1). Do not tighten clamps.
8. Place clamp (10) on air inlet duct (11).
9. Have helper support and rotate heater (4). Install air inlet duct (11) on heater air inlet (12). Secure heater air inlet duct to
bulkhead with two washers (8), new lockwashers (9), and screws (7).
10. Have helper support heater (4). Tighten eight clamp halves (3), two clamps (13), and clamp (10).
11. Connect wiring harness (6) to heater receptacle (5).
NOTE
Do Step 11 only if replacing fuel filter.
12. Install fuel filter (2) on bracket (3) with two screws (1), new lockwashers (5), washers (4), and nuts (6).
0428 00-8
Change 1
TM 9-2350-247-20-3

13. Loosen one clamp half (3) and install fuel filter (6) with bracket on heater (2) and tighten clamp.
14. Install heater fuel hose (2) on fuel filter elbow (1).
15. Connect fuel pump fuel hose (4) to fuel filter elbow (3).
2. Check vehicle compartment heater for proper operation (see your -10).
3. Install front access cover (WP 0391 00).
END OF TASK
0428 00-9/10 blank

Change 1
TM 9-2350-247-20-3
SERVICE VEHICLE COMPARTMENT HEATER FUEL PUMP 0429 00

Service Bendix/Facet (page 0429 00-2).
Service Walbro (page 0429 00-3).
INITIAL SETUP:

Unit See your -10

Battery negative lead(s) disconnected (WP 0292 00)
Gasket Top left access grille removed (see your -10 or
(WP 0390 00))
Gasket
Cab left center floor plate raised (WP 0394 00) or
Personnel Required (WP 0395 00)
Unit Mechanic Heater fuel shutoff valve closed (see your -10)
0429 00-1
TM 9-2350-247-20-3
SERVICE VEHICLE COMPARTMENT HEATER FUEL PUMP — Continued 0429 00
SERVICING
SERVICE BENDIX/FACET
1. Remove cap (1), gasket (2) and strainer (3) from heater fuel pump (4). Discard gasket.
2. Clean cap (1) and strainer (3) with cleaning compound.
3. Check strainer (3). Replace strainer if screen is torn.
WARNING
Wear safety goggles while using compressed air to prevent eye injury or blindness.
4. Dry heater fuel pump parts with low pressure compressed air.
5. Install strainer (3), new gasket (2), and cap (1) on heater fuel pump (4).
0429 00-2
TM 9-2350-247-20-3
SERVICE VEHICLE COMPARTMENT HEATER FUEL PUMP — Continued 0429 00
SERVICE WALBRO
1. Remove three screws (1), cap (2), gasket (3), and strainer (4) from heater fuel pump (5). Discard gasket.
2. Clean cap (2) and strainer (4) with cleaning compound.
3. Check strainer (4). Replace strainer if screen is torn.
WARNING
Wear safety goggles while using compressed air to prevent eye injury or blindness.
4. Dry heater fuel pump parts with low pressure compressed air.
5. Install strainer (4), new gasket (3), cap (2), and three screws (1) on heater fuel pump (5).
2. Open heater fuel shutoff valve (see your -10).
3. Start heater (see your -10).
4. Check heater fuel pump for leaks and proper operation.
5. Stop heater (see your -10).
6. Install top left access grille (see your -10 or (WP 0390 00)).
7. Lower cab left center floor plate (WP 0394 00) or (WP 0395 00).
END OF TASK
0429 00-3/4 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY FUEL PUMP 0430 00

(M548A3)

INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
Sealing Compound (WP 0542 00, Item 33) Engine stopped (see your -10)
Strap Both battery negative leads disconnected (WP 0292 00)
Front access cover removed (WP 0391 00)
REMOVAL
1. Disconnect circuit 402 lead from fuel pump lead (7).
2. Remove screw (4), lock washer (5), washer (6), and capacitor (8) from bulkhead. Discard lock washer.
3. Remove strap (13) from hose (14) and hose (1). Discard strap.
4. Remove hose (1) and elbow (2) from fuel pump (10).
5. Remove hose (14), elbow (3), and adapter (9) from fuel pump (10).
6. Remove two screws (12) and lock washers (11) from fuel pump (10). Remove fuel pump from carrier. Discard lock
washers.
0430 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY FUEL PUMP (M548A3) — 0430 00

Continued
INSTALLATION
1. Install fuel pump (10) in carrier. Secure with two new lock washers (11) and screws (12).
NOTE
Apply sealing compound sparingly to tapered threads of fittings before installation.
2. Apply sealing compound to male threads of fuel pump (10), elbow (3), and elbow (2).
3. Install adapter (9), elbow (3), and hose (14) on fuel pump (10).
4. Install elbow (2) and hose (1) on fuel pump (10).
5. Secure hose (14) and hose (1) with new strap (13)
6. Install capacitor (8), washer (6), new lock washer (5), and screw (14) on bulkhead.
7. Connect circuit 402 lead to fuel pump lead (7).
3. Check fuel pump for leaks (see your -10).
END OF TASK
0430 00-2
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER CONTROL BOX 0431 00

INITIAL SETUP:

Unit See your -10
Lock nut (4)
Lock washer (2)
Unit Mechanic Battery negative lead(s) disconnected (WP 0292 00)
0431 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER CONTROL BOX — Continued 0431 00
REMOVAL
NOTE
Removal of heater control box is similar for M548A1 and M548A3. Differences are noted in
steps.
1. Remove heater control box lead (1) from circuit 400D lead (2).
2. Remove heater wiring harness (3) from receptacle (4) on heater control box (5).
3. Remove screw (6), two lock washers (7), and ground lead (8) from heater control box (5). Discard lock washers.
4. Remove two lock nuts (9), washers (10), mounts (11), and heater control box (5) from hull. Discard lock nuts (M548A1).
5. Remove two lock nuts (9), washers (10), mounts (11), mounts (12), and heater control box (5) from bracket (13).
Discard lock nuts (M548A3).
6. Remove two screws (14), bracket (13), and two lock nuts (15) from hull. Discard lock nuts. (M548A3).
0431 00-2
TM 9-2350-247-20-3
INSTALLATION
NOTE
Installation of heater control box is similar for M548A1 and M548A3. Differences are noted in
steps.
1. Install bracket (1), two screws (2), and new lock nuts (3) on hull (M548A3).
2. Install heater control box (4), two mounts (5), mounts (6), washers (7), and new lock nuts (8) on bracket (1) (M548A3).
3. Install heater control box (4), two mounts (5), washers (7), and new lock nuts (8) on hull (M548A1).
4. Install ground lead (9) on heater control box (4) with two new lock washers (10) and screw (11).
5. Connect wiring harness (12) to receptacle (13) on heater control box (4).
6. Connect circuit 400D lead (14) to heater control box lead (15).
0431 00-3
TM 9-2350-247-20-3
3. Check heater control box for proper operation.
END OF TASK
0431 00-4
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER, HOSES, AND 0432 00

FANS (M548A3)
INITIAL SETUP:

Unit See your -10
Lock washer (2)
Lock washer (4)
Personnel Required
Right center floor plate removed (WP 0395 00)
Unit Mechanic
Helper (H) Tool compartment access door raised (see your -10)
0432 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER, HOSES, AND FANS 0432 00

(M548A3) — Continued
REMOVAL
1. Remove four screws (1), washers (2), and diffuser duct (3) with guard (4) from carrier.
2. Remove four screws (5) and separate guard (4) from diffuser duct (3).
0432 00-2
TM 9-2350-247-20-3

3. Loosen two clamps (1) and remove hose (2) from right defroster (3) and hose (4) from left defroster (5).
4. Remove two screws (6), washers (7), clamps (8), lock nuts (9) and hose (4) from windshield frame. Discard lock nuts.
5. Loosen two clamps (10) and remove hose (2) and hose (4) from defroster duct (11).
6. Remove two screws (12), washers (13), nuts (14), and right defroster (3) from windshield frame.
7. Remove two screws (15), lock washers (16), washers (17), nuts (18), and left defroster (5) from plate (19). Discard lock
washers.
8. Remove two screws (20), washers (21), nuts (22), and plate (19) from left windshield frame.
0432 00-3
TM 9-2350-247-20-3

9. Remove circuit lead 347 (23) from left defroster fan lead (24) and circuit lead 346 (25) from right defroster fan lead (26).
10. Remove six screws (27), lock washers (28), ground lead (29), ground lead (30), defroster fan (31), and defroster fan (32)
from defroster duct (11). Discard lock washers.
11. Loosen clamp (33) securing plenum sleeve (34) to plenum (35).
12. Remove metal hose assembly under plenum (35).
13. Remove four screws (36), lock washers (37), washers (38), and plenum (35) from bulkhead and defroster duct (11).
Have helper assist. Discard lock washers.
14. Remove six screws (39), washers (40), and defroster duct (11) from hull.
0432 00-4
TM 9-2350-247-20-3

INSTALLATION
1. Install plenum (1), four washers (2), new lock washers (3), and screws (4) on bulkhead and heater. Have helper assist.
2. Install metal hose assembly under plenum (1).
3. Install clamp (5) securing plenum sleeve (6) to plenum (1). Tighten clamp.
4. Install defroster duct (7), six washers (8), and screws (9) on hull.
5. Install defroster fan (10), defroster fan (11), ground lead (12), ground lead (13), six new lock washers (14), and screws
(15) on defroster duct (7).
6. Install circuit lead 346 (16) on right defroster fan lead (17) and circuit lead 347 (18) on left defroster fan lead (19).
0432 00-5
TM 9-2350-247-20-3

7. Install plate (20), two nuts (21), washers (22), and screws (23) on left windshield frame.
8. Install left defroster (24), two screws (25), new lock washers (26), washers (27), and nuts (28) on plate (20).
9. Install right defroster (29), two screws (30), washers (31), and nuts (32) on windshield frame.
10. Install two clamps (33) and hose (34) on defroster duct (7) and right defroster (29). Tighten clamps.
11. Install two clamps (35) and two clamps (36) on hose (37). Install hose on defroster duct (7) and left defroster (24).
Tighten clamps (36).
12. Install two clamps (35), washers (38), screws (39), and new lock nuts (40) on windshield frame.
0432 00-6
TM 9-2350-247-20-3

13. Place guard (1) on diffuser duct (2) and secure with four screws (3).
14. Align diffuser duct (2) with defroster duct (4) and install diffuser duct, four washers (5), and screws (6) on carrier.
1. Lower tool compartment access door (see your -10).
2. Install right center floor plate (WP 0395 00).
END OF TASK
0432 00-7/8 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN TOGGLE 0433 00

SWITCHES/IDENTIFICATION PLATE
INITIAL SETUP:

Unit Unit Mechanic
References
Tools and Special Tools See your -10
REMOVAL
1. Remove two circuit 38 leads (1), circuit 347 lead (2), and circuit 346 lead (3) from toggle switch (4) and toggle
switch (5).
2. Remove four screws (6), toggle switch (4), and toggle switch (5) from identification plate (7).
3. Remove two lock nuts (8), washers (9), screws (10), and identification plate (7) from bracket (11). Discard lock nuts.
0433 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN TOGGLE SWITCHES/ 0433 00

IDENTIFICATION PLATE — Continued
INSTALLATION
1. Install identification plate (7) on bracket (11) with two screws (10), washers (9), and new lock nuts (8).
2. Install toggle switch (4) and toggle switch (5) on identification plate (7) with four screws (6).
3. Connect circuit 346 lead (3), circuit 347 lead (2), and two circuit 38 leads (1) to toggle switch (4) and toggle switch (5).
3. Check defroster switches and fans for proper operation.
END OF TASK
0433 00-2
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN WIRING 0434 00

HARNESS
INITIAL SETUP:

Unit See your -10

0434 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN WIRING HARNESS — 0434 00

Continued
REMOVAL
1. Remove two circuit 38 leads (1) from main wiring harness and dome light.
2. Remove circuit 347 lead (2) from left defroster fan (3).
3. Remove circuit 346 lead (4) from right defroster fan (5).
4. Remove circuit 38 lead (6) and circuit 347 lead (7) from left defroster fan toggle switch (8).
5. Remove circuit 38 lead (9) and circuit 346 lead (10) from right defroster fan toggle switch (11). Remove defroster fan
wiring harness (12) from carrier.
0434 00-2
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER DEFROSTER FAN WIRING HARNESS — 0434 00

Continued
INSTALLATION
1. Install defroster fan wiring harness (1) in carrier. Install circuit 38 lead (2) and circuit 346 lead (3) on right defroster fan
toggle switch (4).
2. Install circuit 38 lead (5) and circuit 347 lead (6) on left defroster fan toggle switch (7).
3. Install circuit 346 lead (8) on right defroster fan (9).
4. Install circuit 347 lead (10) on left defroster fan (11).
5. Install circuit 38 lead (12) on carrier wiring harness and dome light.
3. Check defroster fan wiring harness for proper operation.
END OF TASK
0434 00-3/4 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS 0435 00

(M548A3)
INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Grommet Both battery negative leads disconnected (WP 0292 00)
Lock washer Front access cover removed (WP 0391 00)
Personnel Required NBC manifold removed (WP 0533 00)
Unit Mechanic M1A1-19 precleaner assembly removed (WP 0534 00)
0435 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS (M548A3) — 0435 00

Continued
REMOVAL
NOTE
Step 1, Step 2, and Step 3 are accessed through front access cover.
1. Disconnect circuit 402 lead (17) from fuel pump lead (18).
NOTE
Loosen clamp in order to move fuel filter on bracket for access to receptacle.
2. Disconnect wiring harness connector (3) from receptacle (2) on heater (1).
3. Remove screw (15), lock washer (14), washer (13), ground lead (4), and clamp (5) from hull weld nut and wiring
harness (12). Discard lock washer.
0435 00-2
TM 9-2350-247-20-3

Continued
NOTE
Step 4, Step 5, and Step 6 are accessed from inside cab.
4. Disconnect wiring harness connector (8) from receptacle (10) on heater control box (9).
5. Remove three screws (6), washers (7), clamps (11), and wiring harness (12) from hull weld nuts.
6. Cut grommet (16) from hull and wiring harness (12). Remove wiring harness from hull. Discard grommet.
0435 00-3
TM 9-2350-247-20-3

Continued
INSTALLATION
1. Install wiring harness (12) and new grommet (16) in hull.
2. Install three clamps (11) on wiring harness (12). Secure clamps to hull weld nuts with three washers (7) and screws (6).
NOTE
Position fuel filter on bracket on heater and tighten clamp.
3. Connect wiring harness connector (8) to receptacle (10) on heater control box (9).
0435 00-4
TM 9-2350-247-20-3

Continued
4. Install clamp (5) on wiring harness (12). Secure clamp and ground lead (4) to hull weld nut with washer (13), new lock
washer (14), and screw (15).
5. Connect wiring harness connector (3) to receptacle (2) on heater (1).
6. Connect circuit 402 lead (17) to fuel pump lead (18).
4. Install M1A1-19 precleaner assembly (WP 0534 00).
5. Install NBC manifold (WP 0533 00).
END OF TASK
0435 00-5/6 blank

TM 9-2350-247-20-3
SERVICE PERSONNEL HEATER FUEL FILTER 0436 00

INITIAL SETUP:
Unit Unit Mechanic


Cleaning compound (WP 0542 00, Item 9) Engine stopped (see your -10)
Wiping rag (WP 0542 00, Item 45) Carrier blocked (see your -10)
Preformed packing
Separator parts kit
REMOVAL
NOTE
Service steps are the same for M548A1 and M548A3, only the locations are different.
1. Depress plunger (7) until fluid is drained from collector bowl (6). Wipe up spilled fuel.
2. Remove collector bowl (6) from filter element (4).
NOTE
Loosen head bolt as instructed. Do not remove head bolt from filter head. Do not discard
head gasket.
3. Loosen head bolt (1) until filter element (4) with preformed packing (5) can be removed from filter head (2). Do not
remove and do not discard head gasket (3). Discard preformed packing and filter element.
0436 00-1
Change 1
TM 9-2350-247-20-3
SERVICE PERSONNEL HEATER FUEL FILTER — Continued 0436 00
CLEANING
1. Clean collector bowl (6) with cleaning compound and clean wiping rag.
INSTALLATION
1. Install new preformed packing (5) on new filter element (4).
2. Install collector bowl (6) in new filter element (4).
3. If head gasket (3) was removed, position same gasket in filter head (2) or on filter element (4).
4. Install new filter element (4) and gasket (3) on head bolt (1) and filter head (2).
1. Turn personnel heater ON (see your -10). Check for leaks.
2. Turn personnel heater OFF (see your -10).
END OF TASK
0436 00-2
Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST METAL HOSE 0437 00

ASSEMBLY (M548A3)
INITIAL SETUP:

Unit See your -10

Lock washer (11)
Front access cover removed (WP 0391 00)
Personnel Required Right floor plate removed (WP 0395 00)
Unit Mechanic Top right access grille removed (see your -10)
Helper (H) Center seat raised (see your -10)
0437 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST METAL HOSE ASSEMBLY 0437 00

REMOVAL
1. Loosen clamp (1) on metal hose assembly (2).
2. Remove two screws (4), lock washers (5), washers (6), and metal hose assembly (2) from hull. Have helper assist.
3. Remove two screws (7), lock washers (8), washers (9), and clamps (10) from two hull weld nuts. Discard lock washers.
5. Remove two screws (12), lock washers (13), washers (14), and metal hose assembly (3) from hull. Have helper assist.
0437 00-2
TM 9-2350-247-20-3

6. Remove two screws (1), lock washers (2), washers (3), clamps (4) and metal hose assembly (5) from two hull weld nuts.
8. Remove screw (7), lock washer (8), washer (9), and clamp (10) from hull weld nut. Discard lock washer.
9. Remove metal hose assembly (5) from pipe (11).
10. Loosen two clamps (12) and remove exhaust pipe (13) from pipe (11) and heater (WP 0428 00).
11. Remove two nuts (14), lock washers (15), washers (16), and screws (17) securing pipe (11) to bulkhead. Have helper
assist. Remove pipe. Discard lock washers.
0437 00-3
TM 9-2350-247-20-3

INSTALLATION
1. Install pipe (11) on bulkhead. Secure with two washers (16), new lock washers (15), nuts (14), and screws (17). Have
helper assist.
2. Install two clamps (12) on exhaust pipe (13).
3. Install exhaust pipe (13) on pipe (11) and heater (WP 0428 00). Tighten two clamps (12).
4. Install clamp (10) and clamp (6) on metal hose assembly (5).
5. Install metal hose assembly (5) on pipe (11) and secure with clamp (6). Secure metal hose assembly to hull weld nut
with clamp (10), washer (9), new lock washer (8), and screw (7). Tighten clamps.
0437 00-4
TM 9-2350-247-20-3

6. Install clamp (1) on metal hose assembly (2).

7. Install two clamps (3) on metal hose assembly (2). Insert end of metal hose assembly through hull and secure with two
washers (4), new lock washers (5) and screws (6). Have helper assist.
8. Insert metal hose assembly (7) into metal hose assembly (2) and clamp (1). Tighten clamp. Secure metal hose assembly
to two hull weld nuts with two clamps (8), washers (9), new lock washers (10), and screws (11).
0437 00-5
TM 9-2350-247-20-3

9. Secure two clamps (3) and metal hose assembly (2) on two hull weld nuts with two washers (12), new lock washers (13),
and screws (14).
10. Install metal hose assembly (15) and clamp (16) on metal hose assembly (2). Tighten clamp.
11. Install end of metal hose assembly (15) through bulkhead. Secure with two washers (17), new lock washers (18), and
screws (19). Have helper assist.
2. Install top right access grille (see your -10).
3. Install right floor plate (WP 0395 00).
END OF TASK
0437 00-6
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER AIR INLET DUCTS (M548A3) 0438 00

INITIAL SETUP:

Unit See your -10
Seal Front access cover removed (WP 0391 00)
Personnel Required Left front lifting eye removed (WP 0382 00) or machine
Unit Mechanic gun mount removed (WP 0513 00), (WP 0514 00) or
Helper (H) (WP 0515 00), if installed
0438 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER AIR INLET DUCTS (M548A3) — Continued 0438 00
REMOVAL
NOTE
Heater air inlet duct will be behind left front lifting eye or machine gun mount, if installed.
1. Remove two screws (1), washers (2), and lock washers (3) from air inlet duct (4). Discard lock washers.
2. Loosen clamp (5) and remove air inlet duct (4) from heater (6) and tube (7).
3. Remove two screws (8), washers (9), and lock washers (10) from cover (11). Discard lock washers.
4. Remove cover (11), flange (12), seal (13), and tube (7) from carrier. Discard seal.
0438 00-2
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER AIR INLET DUCTS (M548A3) — Continued 0438 00
INSTALLATION
1. Slide tube (1) through top plate and align with air inlet duct (2) opening. Have helper assist.
2. Place clamp (3) on air inlet duct (2) and install duct on tube (1) and heater (4). Tighten clamp.
3. Install two new lock washers (5), washers (6), and screws (7) on air inlet duct (2) and tube (1).
4. Install new seal (8), flange (9), and cover (10) on tube (1).
5. Secure cover (10) on tube (1) and top plate with two new lock washers (11), washers (12), and screws (13).
2. Install left front lifting eye (WP 0382 00) or machine gun mount (WP 0513 00), (WP 0514 00) or (WP 0515 00), if
removed.
END OF TASK
0438 00-3/4 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES TO FUEL/ 0439 00

SEPARATOR FILTER (M548A3)
INITIAL SETUP:

Unit See your -10

Sealing Compound (WP 0542 00, Item 33) Center floor plates removed (WP 0395 00)
Lock washer (7) Top center access grille removed (see your -10)
Strap Power plant rear access panel removed (see your -10)
Personnel Required Center seat raised (see your -10)
Unit Mechanic Hull bottom access cover removed (WP 0383 00)
Radiator removed (WP 0216 00)
0439 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES TO FUEL/SEPARATOR 0439 00

FILTER (M548A3) — Continued
REMOVAL
NOTE
Perform steps necessary to access fuel line on heater for removal.
1. Loosen all clamps securing heater and sleeve. Remove air inlet duct and exhaust pipe from heater (WP 0428 00).
2. Remove strap (15) from hose (1) and hose (4). Discard strap.
3. Remove hose assembly (1) from elbow (2) and adapter (3).
4. Remove hose assembly (4) from elbow (5) and elbow (6).
5. Loosen nut (7). Remove hose assembly (8) from elbow (9).
0439 00-2
TM 9-2350-247-20-3

NOTE
Access through bottom access cover and from power plant rear access panel for Step 6.
6. Remove seven screws (10) and lock washers (11) from seven clamps (12). Remove clamps from bulkhead and hose
assembly (8). Discard lock washers.
7. Loosen nut (13). Remove hose assembly (8) from adapter (14).
8. Remove hose assembly (8) from carrier.
0439 00-3
TM 9-2350-247-20-3

INSTALLATION
NOTE
1. Install hose assembly (1) on elbow (2) and adapter (3). Tighten nut (4) and nut (5).
NOTE
Access through bottom access cover and from power plant rear access panel for Step 1.
2. Install seven clamps (6) on hose assembly (1). Secure clamps and hose assembly to bulkhead with seven new lock
washers (7) and screws (8).
0439 00-4
TM 9-2350-247-20-3

3. Install hose assembly (9) on elbow (10) and elbow (11).

4. Install hose assembly (12) on elbow (13) and adapter (14).
5. Secure hose (9) and hose (12) together with new strap (15).
6. Install air inlet duct and exhaust pipe on heater. Tighten all clamps to secure heater and sleeve (WP 0428 00).
1. Install radiator (WP 0216 00).
3. Check vehicle compartment heater for leaks (see your -10).
4. Install power plant rear access panel (see your -10)
5. Install top center access grille (see your -10).
7. Install center floor plates (WP 0395 00).
8. Install hull bottom access cover (WP 0383 00).
END OF TASK
0439 00-5/6 blank

TM 9-2350-247-20-3
REPLACE PLATES, STENCILS, DECALS, RUBBER PADS, AND STRAPS 0440 00

Removal of Vehicle Identification Plates (page 0440 00-2).
Installation of Vehicle Identification Plates (page 0440 00-3).
Cleaning of Stencils (page 0440 00-3).
Removal of Decals (page 0440 00-3).
Installation of Decals (page 0440 00-5).
Removal of Rubber Pads and Strips (page 0440 00-6).
Installation of Rubber Pads and Strips(page 0440 00-6).
Removal of Straps (page 0440 00-7).
Installation of Straps (page 0440 00-8).
INITIAL SETUP:

Unit Unit Mechanic
Drill Bit Set (WP 0541 00, Item 14) See your -10
Hand Blind Riveter Kit (WP 0541 00, Item 42) TB 43-0209
Materials/Parts
Equipment Condition
Insulating varnish (WP 0542 00, Item 19) Engine stopped (see your -10)
Rubber pads Carrier blocked (see your -10)
0440 00-1
TM 9-2350-247-20-3
REPLACE PLATES, STENCILS, DECALS, RUBBER PADS, AND STRAPS — Continued 0440 00
REMOVAL OF VEHICLE IDENTIFICATION PLATES
NOTE
Plates, stencils, and decals should be cleaned, replaced, or repainted when they become too hard
to read. See WP 0441 00 and WP 0442 00 for location.
NOTE
Remove and install all metal plates in the same way.
1. Drill out four rivets (1). Remove plate (2).
0440 00-2
TM 9-2350-247-20-3
INSTALLATION OF VEHICLE IDENTIFICATION PLATE
NOTE
Use plate as template and drill four new holes.
1. Place plate (2) so holes in plate line up with new holes in door.
2. Attach plate (2) to door with drive screws or rivets (1).
CLEANING OF STENCILS
1. Clean stencil with cleaning compound. If stencil needs to be repainted, see TB 43-0209.
REMOVAL OF DECALS
1. Inspect caution markers for damage and legibility. Replace damaged and illegible cautions markers (see your -10).
0440 00-3
TM 9-2350-247-20-3
2. Remove decals with cleaning compound.
0440 00-4
TM 9-2350-247-20-3
INSTALLATION OF DECALS
NOTE
If your carrier does not have caution markers that say: HIGH INTENSITY NOISE, HEARING
PROTECTION REQUIRED, obtain them. Position and install them as indicated:
1. Install new decal. Apply one coat of full strength insulating varnish over decal.
0440 00-5
TM 9-2350-247-20-3
REMOVAL OF RUBBER PADS AND STRIPS

1. Remove rubber pads and strips by scraping. Discard rubber pads.
INSTALLATION OF RUBBER PADS AND STRIPS

1. Clean hull surface where pad is to be placed.
2. Apply thin coat of adhesive to hull and back of new rubber pad.
3. Allow 10 to 20 minutes to dry. Surface should be tacky, not too sticky. Warmer temperatures mean a shorter drying time.
0440 00-6
TM 9-2350-247-20-3
4. Place pad on hull surface and press firmly.
REMOVAL OF STRAPS
NOTE
There are 43 straps used to secure stowed items to hull. See your -10 for location.
1. Unbuckle and remove strap (1) from footman’s loop (2).
0440 00-7
TM 9-2350-247-20-3
INSTALLATION OF STRAPS
1. Pass strap (1) through footman’s loop (2) and over item to be secured. Fasten strap.
END OF TASK
0440 00-8
TM 9-2350-247-20-3
DATA PLATE, MARKER, AND DECAL CHART (M548A1) 0441 00

Data plate, marker, and decal locations (page 0441 00-1).
INITIAL SETUP:
Maintenance Level
Unit
DATA PLATE, MARKER, AND DECAL LOCATIONS
1. The following chart is for location of all data plates, markers, and decals common to the M548A1 carrier. See
(WP 0442 00) for plates, markers, stencils, and decals unique to the M548A3 carrier.
0441 00-1
TM 9-2350-247-20-3
DATA PLATE, MARKER, AND DECAL CHART (M548A1) — Continued 0441 00
Table 1. DATA PLATE, MARKER, AND DECAL LOCATIONS
1. Plate, identification, vehicle operation 11. Decal, master switch instructions

2. Marker, WARNING, stall check 12. Plate, instruction, differential oil
3. Marker, instruction, power train maintenance 13. Marker, identification, bilge pump
4. Marker, instruction, speed shift limit 14. Decal, pivot steer brakes
5. Plate, instruction, engine idle RPM 15. Decal, fire extinguisher
6. Plate, identification, vehicle 16. Decal, first aid kit
7. Plate, identification, vehicle shipping data 17. Decal, flashlight
8. Marker, engine disconnect 18. Decal, pamphlet bag
9. Marker, instruction, noise caution 19. Decal, load limit
10. Decal, spare barrel
END OF TASK
0441 00-2
TM 9-2350-247-20-3
DATA PLATE, MARKER, AND DECAL CHART (M548A3) 0442 00

Data plate, marker, and decal locations (page 0442 00-1).
INITIAL SETUP:
Maintenance Level
Unit
DATA PLATE, MARKER, AND DECAL LOCATIONS
1. The following chart is for location of all data plates, markers, and decals for M548A3 carrier. See (WP 0441 00) for
plates, markers, stencils, and decals for the M548A1 carrier.
0442 00-1
TM 9-2350-247-20-3
DATA PLATE, MARKER, AND DECAL CHART (M548A3) — Continued 0442 00
Table 1. DATA PLATE, MARKER, AND DECAL LOCATIONS
1. Marker, vehicle operation 11. Marker, identification bilge pump

2. Marker, WARNING, stall check 12. Decal, fire extinguisher
3. Marker, instruction, power train 13. Decal, first aid kit
4. Marker, instruction, speed shift limit 14. Decal, flashlight
5. Plate, instruction, engine idle RPM 15. Decal, pamphlet bag
6. Plate, identification, vehicle 16. Decal, WARNING, pivot steer
7. Plate, identification, vehicle shipping data 17. Marker, WARNING, pivot steer and lock pin
8. Marker, instruction, noise caution 18. Plate, warranty
9. Decal, spare barrel 19. Marker, CARC, paint
10. Decal, master switch instructions 20. Decal, load limit
END OF TASK
0442 00-2
TM 9-2350-247-20-3
CHAPTER 21
FOR TOOLS AND TEST EQUIPMENT
WORK PACKAGE INDEX

Title Sequence No.
INSPECT POWER PLANT SLING..................................................................................................................................0443 00
TM 9-2350-247-20-3
INSPECT POWER PLANT SLING 0443 00

Periodic Check (page 0443 00-1).

Preoperative Check (page 0443 00-7).
INITIAL SETUP:

Unit Unit Mechanic

General Mechanic’s Tool Kit (WP 0541 00, Item 57) Sling suspended from suitable lifting device
Drill set (WP 0541 00, Item 14)
Straight edge (WP 0541 00, Item 50)
Measuring tape (WP 0541 00, Item 52)
Suitable Lifting Device
PERIODIC CHECK
WARNING
Damaged lifting slings can fall with load. Personnel can be injured or killed. Inspect all slings.
Do not use damaged slings.
NOTE
Chains are inspected on a link by link basis with the chain slack.
1. Check chains (1) for excessive wear.
a. For 9/32 inch (7 mm) chain, if any link (2) is worn at any point in excess of 3/64 inch (1 mm) or chain size is less
than 15/64 inch (6 mm) in diameter, remove sling from service. Use drill set as No-Go gauge and/or caliper.
b. For 3/8 inch (10 mm) chain, if any link (2) is worn at any point in excess of 5/64 inch (2 mm) or chain size is less
than 19/64 inch (8 mm) in diameter, remove sling from service. Use drill set as No-Go gauge and/or caliper.
2. Check chains (1) for excessive stretch.
a. If any link (2) does not hinge freely with adjoining link, remove sling from service.
0443 00-1
TM 9-2350-247-20-3
INSPECT POWER PLANT SLING — Continued 0443 00
NOTE
Dimension “L” or “reach” is the distance between the bearing point of hook to bearing point on
coupling link while under a light load.
If identification tag attached to chain leg does not contain “reach” dimensions, then dimension
“L” must be calibrated prior to use for each chain leg and entered into maintenance record. At
each inspection, chain length must be compared with initial inspection.
b. If length (L) between bearing point of hook (1) and bearing point of coupling link (2) while under light load is
greater than the maximum in Table I, remove sling from service.
0443 00-2
TM 9-2350-247-20-3
Table 1.
(L) (L)
Part Nominal Maximum
Number Reach Reach Example
12350350-1 13-1/2 2% Increase 13-3/4
(34.3 cm) (34.9 cm)
12350350-2 12-3/4 2% Increase 13
(32.4 cm) (33 cm)
12350350-6 16-7/8 2% Increase 17-1/5
(42.9 cm) (43.7 cm)
0443 00-3
TM 9-2350-247-20-3
3. Check chains (3) for following:

a. If any link (4) is bent or twisted, remove sling from service.
b. If any link (4) has a sharp transverse nick or gouge, remove sling from service.
c. If any link (4) is modified, homemade, or length of chain is altered, remove sling from service.
NOTE
Hooks should be free of paint. Paint covers up cracks. Remove all paint from hooks.
4. Inspect hooks (5) for following:

a. If any cracks are found on hooks (5), remove sling from service.
b. If throat opening (6) exceeds 1 7/64 inch (28 mm), remove sling from service.
c. If twisting exceeds 10 from centerline, remove sling from service.
d. Inspect safety closure latch (7). If any latch is damaged, remove sling from service.
0443 00-4
TM 9-2350-247-20-3
5. Inspect lifting shackle (1) for following:

a. Verify correct lifting shackle (1) is being used. Part number 12328579 and/or SWL21T should be visible in raised
letters.
b. Verify correct bolt (2) is being used. Diameter of bolt should be 1 3/8 inch (35 mm), and bolt head should be
marked with HS in raised letters. Nut (3) should be snug and a cotter pin (4) must be installed through bolt.
c. If any cracks are found in lifting shackle (1), remove sling from service.
d. Lifting shackle (1) must have a minimum width of 1 31/32 inch (5 cm) between eyes (5). If shackle has a visible
decrease in eye width or bending and deformation and damaged threads, remove sling from service.
0443 00-5
TM 9-2350-247-20-3
NOTE
Make sure pin is secure in shackle.
6. Inspect welded shackles (6) for following:

a. If any welds are cracked or missing, remove sling from service.
b. If welded shackle (6) has any visible decrease in width between eyes (7) or twisting, bending, and deformation,
remove sling from service.
0443 00-6
TM 9-2350-247-20-3
NOTE
Use straight edge to measure cross beam bend.
7. Inspect structural members for following:
a. If welded joints are cracked in excess of 1/2 inch (13 mm) or 25% of length of weld in gusset (1) to cross beam (2)
area, remove sling from service.
b. If cross beam is bent or twisted in excess of 1/4 inch (6 mm) at ends of cross beam, remove sling from service. Do
not attempt to straighten a bent cross beam.
c. If lifting hole (3) is elongated in excess of 1/8 inch (3 mm), remove sling from service.
8. Complete required forms.
PREOPERATIVE CHECK
WARNING
Damaged lifting slings can fall with load. Personnel can be injured or killed. Inspect all slings.
Do not use damaged slings.
NOTE
Chains are inspected on a link by link basis with the chain slack.
1. Do Periodic Check Procedure Step 2a and Steps 3 - 8.
END OF TASK
0443 00-7/8 blank

TM 9-2350-247-20-3
CHAPTER 22
FOR SPECIAL PURPOSE KITS
WORK PACKAGE INDEX

Title Sequence No.
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES, TUBES, AND FITTINGS
(KIT I) (M548A1).....................................................................................................................................................0444 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES, TUBES, AND FITTINGS
(KIT II OR III) (M548A1)........................................................................................................................................0445 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY (KIT I) (M548A1)....................................................0446 00
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY (KIT II OR III) (M548A1).......................................0447 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP (KIT I) (M548A1)...................................................0448 00
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP (KIT II OR III) (M548A1)......................................0449 00
REPLACE VEHICLE COMPARTMENT HEATER CONTROLS COVER (M548A1)..................................................0450 00
REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS (M548A1)....................................................0451 00
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT I) (M548A1)..............................0452 00
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT II)
(M548A1).................................................................................................................................................................0453 00
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT III)
(M548A1).................................................................................................................................................................0454 00
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST GUARD (M548A1)....................................................0455 00
REPLACE FIBERGLASS CAB COVER..........................................................................................................................0456 00
REPLACE FIBERGLASS MACHINE GUN HATCH COVER.......................................................................................0457 00
REPLACE CAB WINDOWS............................................................................................................................................0458 00
REPLACE LOWER CAB INSULATION.........................................................................................................................0459 00
REPLACE CLOTH SEAT COVERS.................................................................................................................................0460 00
REPLACE THERMAL DOOR WINDOWS.....................................................................................................................0461 00
REPLACE CARGO AREA HEATER AND CONTROL BOX MOUNTING..................................................................0462 00
REPLACE CARGO AREA HEATER FUEL LINES, FITTINGS AND SHIELDS.........................................................0463 00
REPLACE CARGO AREA HEATER FUEL PUMP........................................................................................................0464 00
REPLACE CARGO AREA HEATER WIRING HARNESS............................................................................................0465 00
REPLACE INSULATED CARGO COVERS....................................................................................................................0466 00
REPLACE ESCAPE HATCH COVER..............................................................................................................................0467 00
REPLACE INSULATED COVER WINDOWS................................................................................................................0468 00
REPLACE CARGO DOOR INSULATION......................................................................................................................0469 00
REPLACE FLOOR PLATE COVERS...............................................................................................................................0470 00
REPLACE PERSONNEL SEAT COVERS.......................................................................................................................0471 00
REPLACE/REPAIR HEATER CONTROL BOX..............................................................................................................0472 00
REPLACE ENGINE COOLANT HEATER WIRING HARNESS...................................................................................0473 00
REPLACE ENGINE COOLANT HEATER CONTROL BOX.........................................................................................0474 00
REPLACE ENGINE COOLANT HEATER FUEL PUMP/FUEL LINES........................................................................0475 00
REPLACE BATTERY BOX HEAT EXCHANGER/HOSES/FITTINGS.........................................................................0476 00
REPLACE ENGINE COOLANT HEATER......................................................................................................................0477 00
TM 9-2350-247-20-3
CHAPTER 22
FOR SPECIAL PURPOSE KITS
WORK PACKAGE INDEX (Continued)

Title Sequence No.
REPLACE ENGINE COOLANT HEATER COOLANT PUMP......................................................................................0478 00
REPLACE ENGINE COOLANT/VEHICLE COMPARTMENT HEATER EXHAUST PIPES
GUARD (M548A1)..................................................................................................................................................0479 00
REPLACE ENGINE COOLANT HEATER EXHAUST SYSTEM (M548A1)................................................................0480 00
REPLACE ENGINE COOLANT HEATER EXHAUST SYSTEM (M548A3)................................................................0481 00
REMOVE/INSTALL MATERIAL HANDLING KIT.......................................................................................................0482 00
REPLACE BEAM/BEAM SUPPORTS/STOPS...............................................................................................................0483 00
REPLACE HOIST/STOPS/SLING....................................................................................................................................0484 00
REPAIR HOIST ASSEMBLY...........................................................................................................................................0485 00
REPLACE PERSONNEL SEATS/SAFETY BELT...........................................................................................................0486 00
REMOVE/INSTALL BULKHEAD PROTECTOR...........................................................................................................0487 00
REPLACE RIFLE RACK..................................................................................................................................................0488 00
REPLACE AIR BRAKE COMPRESSOR (M548A1)......................................................................................................0489 00
REPLACE AIR BRAKE GOVERNOR (M548A1)...........................................................................................................0490 00
REPLACE AIR BRAKE RESERVOIR (M548A1)...........................................................................................................0491 00
REPLACE AIR BRAKE SAFETY VALVE (M548A1)....................................................................................................0492 00
REPLACE STOPLIGHT SWITCH (M548A1).................................................................................................................0493 00
REPLACE AIR LOW PRESSURE SWITCH (M548A1).................................................................................................0494 00
REPLACE AIR HOSES/TUBES/FITTINGS (M548A1)..................................................................................................0495 00
REPLACE OIL HOSES/FITTINGS (M548A1)................................................................................................................0496 00
REPLACE COMPRESSOR DRIVE BELT GUARD (M548A1)......................................................................................0497 00
ADJUST/ALIGN COMPRESSOR DRIVE PULLEY/BELTS (M548A1).......................................................................0498 00
REPLACE COMPRESSOR DRIVE PULLEY/BELTS (M548A1)..................................................................................0499 00
REPLACE AIR STRAINER (M548A1)............................................................................................................................0500 00
REPLACE AIR BRAKE INSTRUMENT PANEL (M548A1)..........................................................................................0501 00
REPLACE AIR LOW PRESSURE WARNING LIGHT (M548A1).................................................................................0502 00
REPLACE AIR BRAKE PRESSURE INDICATOR (M548A1)......................................................................................0503 00
REPLACE AIR BRAKE PANEL LIGHT (M548A1).......................................................................................................0504 00
REPLACE TURN SIGNAL LIGHT..................................................................................................................................0505 00
REPLACE BLACKOUT MARKER LIGHT.....................................................................................................................0506 00
REPLACE BLACKOUT STOPLIGHT-TAILLIGHT.......................................................................................................0507 00
REPLACE TURN SIGNAL CONTROL/MOUNT...........................................................................................................0508 00
REPLACE FLASHER........................................................................................................................................................0509 00
REPLACE REFLECTOR..................................................................................................................................................0510 00
REPLACE TURN SIGNAL FRONT WIRING HARNESS..............................................................................................0511 00
REPLACE TURN SIGNAL REAR WIRING HARNESS................................................................................................0512 00
REPLACE CALIBER .50 MACHINE GUN MOUNT.....................................................................................................0513 00
REPLACE M66 RING MOUNT KIT................................................................................................................................0514 00
REPLACE 7.62 MM MACHINE GUN MOUNT.............................................................................................................0515 00
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES, TUBES, AND 0444 00

FITTINGS (KIT I) (M548A1)

INITIAL SETUP:

Unit See your -10

Sealing compound (WP 0542 00, Item 33) Carrier blocked (see your -10)
Personnel Required Top left access grille removed (WP 0390 00)
REMOVAL
1. Remove hose (1) from nipple (2) and elbow (3).
2. Remove nipple (2) from heater (4). Remove elbow (3) from fuel pump (5).
3. Remove hose (6) from nipple (7) and primary fuel filter (8).
4. Remove tee (9) and nipple (10) from fuel pump (5).
0444 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES, TUBES, AND FITTINGS 0444 00
(KIT I) (M548A1) — Continued
INSTALLATION
NOTE
1. Install nipple (10) and tee (9) in fuel pump (5).
2. Install nipple (7) in tee (9). Connect hose (6) to nipple and primary fuel filter (8).
3. Install elbow (3) in fuel pump (5). Install nipple (2) in heater (4).
4. Connect hose (1) to elbow (3) and nipple (2).
*FOLLOW-THROUGH STEPS
3. Check heater for leaks and proper operation.
5. Install top left access grille (WP 0390 00).
END OF TASK
0444 00-2
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL HOSES, TUBES, 0445 00

AND FITTINGS (KIT II OR III) (M548A1)
INITIAL SETUP:

Unit Unit Mechanic

Suitable Container
Equipment Condition
Wiping rag (WP 0542 00, Item 45) Battery negative lead disconnected (WP 0292 00)
Lockwasher (4) Top left access grill removed (WP 0390 00)
Locknut (2)
Preformed packing
Preformed packing (2)
REMOVAL
NOTE
Use suitable container to hold fuel still in fuel lines and heater components. Install covers on
disconnected fuel lines, tubes, and heater components during maintenance. Use tape, cloth,
cardboard, or any appropriate material to prevent damage to components or accidental fuel
spills.
0445 00-1
Change 1
TM 9-2350-247-20-3

FITTINGS (KIT II OR III) (M548A1) — Continued
1. Remove hose (1) from elbow (2) and elbow (3).

2. Remove four screws (4), four lockwashers (5), two locknuts (6), and four clamps (7) securing hose (1) to bulkhead.
Discard lockwashers and locknuts.
3. Remove elbow (2) from coupling (8).
4. Remove coupling (8) from fuel pump (9).
0445 00-2
Change 1
TM 9-2350-247-20-3

5. Remove elbow (3), nut (10), and preformed packing (11) from fuel manifold block (12). Discard preformed packing.
6. Remove hose (13) from elbow (14) and elbow (15).
7. Remove elbow (14) from coupling (16). Remove coupling (16) from fuel pump (9).
8. Remove hose (18) from elbow (15) and nipple (19). Remove two elbows (15), adapters (20) and packings (21) from
fuel filter (17). Discard packings.
9. Remove nipple (19), nipple (22), and coupling (23) from cab heater (24).
0445 00-3
Change 1
TM 9-2350-247-20-3

INSTALLATION
WARNING
Adhesive, primer, sealant compounds, and isopropyl alcohol are toxic and flammable. These
compounds are toxic to eyes, skin, and respiratory tract. Continued exposure can make you
dizzy and irritate your eyes and throat.
Always use in well ventilated areas, away from heat, sparks, and flames. Do not breathe fumes.
Do not allow into contact with skin and eyes. Use goggles or face shield and protective gloves.
NOTE
1. Install nipple (1), nipple (2), and coupling (3) in cab heater (4).
2. Install two new packings (5), adapters (6), and elbows (7) on fuel filter (10).
3. Install couplings (11) and (12) on fuel pump (13).
4. Install elbow (14) and elbow (15) in coupling (11) and coupling (12).
0445 00-4
Change 1
TM 9-2350-247-20-3

5. Install new preformed packing (16), nut (17), and elbow (18) in fuel manifold block (19).
6. Connect hose (8) to elbow (7) and (14).
7. Connect hose (9) to nipple (2) and elbow (7).
8. Connect hose (20) to elbow (18) and elbow (15).
9. Install four clamps (21), two new locknuts (22), four new lockwashers (23), and four screws (24) securing hose (20)
to bulkhead.
3. Check heater fuel hoses, tubes, and fittings for leaks and proper operation.
5. Install top left access grill (WP 0390 00).
END OF TASK
0445 00-5/6 blank

Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY (KIT I) (M548A1) 0446 00

INITIAL SETUP:

Unit See your -10
Portable Electric Drill (WP 0541 00, Item 13) Engine stopped (see your -10)
Drill Set (WP 0541 00, Item 14) Carrier blocked (see your -10)
Materials/Parts Battery negative lead disconnected (WP 0292 00)
Rubber adhesive tape (WP 0542 00, Item 32) Bulkhead protector removed, if material handling kit is
Grommet installed (WP 0487 00)
Lock washer Power plant rear access door removed (see your -10)
Unit Mechanic Heater exhaust pipe removed (WP 0209 00)
0446 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY (KIT I) (M548A1) — Continued 0446 00
REMOVAL
1. Disconnect wiring harness (1) at heater (2).
2. Loosen clamp (3). Disconnect intake hose (4) from intake duct (5).
0446 00-2
TM 9-2350-247-20-3
3. Loosen clamp (1). Disconnect outlet hose (2) from plenum chamber (3).
4. Disconnect fuel hose (4) from heater (5).
5. Loosen clamp (6) at heater (5). Disconnect exhaust pipe (7) from heater.
6. Remove screw (8) and lock washer (9). Disconnect ground strap (10) from plenum chamber (3). Discard lock washer.
0446 00-3
TM 9-2350-247-20-3
7. Loosen clamp (11). Disconnect defroster tube (12) from plenum chamber (3).
8. Open two clamps (13). Remove heater (5) from two brackets (14) with plenum chamber (3) and intake duct (15)
attached.
9. Remove three screws (8), washers (9), and plenum chamber (3) from heater (5).
10. Remove four screws (16) and intake duct (15) from heater (5).
0446 00-4
TM 9-2350-247-20-3
INSTALLATION
NOTE
If new heater is Model 8460C, do Steps 1 - 10.
1. Remove heater controls cover (WP 0450 00).
2. Remove screw (1), washer (2), and blower lead 6 (3) from terminal board (4).
3. Remove four screws (5) and heater blower (6) from heater housing (7).
4. Remove grommet (8) from heater housing (7). Discard grommet.
5. Drill new hole (9) 19/32 in (15 mm) into heater housing (7).
6. Install new grommet (8) in new 19/32 in (15 mm) hole in heater housing (7).
7. Thread blower lead 6 (3) through new grommet (8) to terminal board (4). Secure with washer (2) and screw (1).
8. Install heater blower (6) in heater housing (7) with four screws (5).
9. Cover old opening (10) with rubber adhesive tape.
0446 00-5
TM 9-2350-247-20-3
10. Install heater controls cover (WP 0450 00).

11. Install intake duct (1) on heater (2) with four screws (3).
12. Install plenum chamber (4) on heater (2) with three screws (5) and washers (6).
13. Place heater (2), with intake duct (1) and plenum chamber (4) attached, on two brackets (7). Secure with two clamps (8).
14. Install defroster tube (9) on plenum chamber (4) with clamp (10).
15. Install ground strap (11) on plenum chamber (4) with new lock washer (6) and screw (5).
16. Install exhaust pipe (12) on heater (2) with clamp (13). Connect fuel hose (14) to heater.
17. Install outlet hose (15) on plenum chamber (4) with clamp (16).
18. Install intake hose (17) on intake duct (1) with clamp (18). Connect wiring harness (19) to heater (2).
0446 00-6
TM 9-2350-247-20-3
2. Install bulkhead protector, if material handling kit is installed (WP 0484 00).
3. Install heater exhaust pipe (WP 0209 00).
6. Start heater (see your -10). Check heater for proper operation.
END OF TASK
0446 00-7/8 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY 0447 00

(KIT II OR III) (M548A1)
INITIAL SETUP:

Unit Unit Mechanic

Drill Set (WP 0541 00, Item 14) See your -10
General Mechanic’s Tool Kit (WP 0541 00, Item 57) TM-9-2540-207-14&P
Portable Electric Drill (WP 0541 00, Item 13)
Equipment Condition
Adhesive (WP 0542 00, Item 2.1) Carrier blocked (see your -10)
Rubber adhesive tape (WP 0542 00, Item 32) Battery negative lead disconnected (WP 0292 00)
Grommet Bulkhead protector removed, if material handling kit is
Locknut (2) installed (WP 0487 00)
Lockwasher Power plant rear access door removed (see your -10)
Heater exhaust pipe guard removed (WP 0455 00)
REMOVAL
1. Disconnect wiring harness (1) at heater (2).
2. Loosen clamp (3). Disconnect intake hose (4) from intake duct (5).
3. Loosen clamp (6). Disconnect outlet hose (7) from plenum chamber (8). Disconnect fuel hose (9) from heater (2).
0447 00-1
Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER ASSEMBLY (KIT II OR 0447 00

III) (M548A1) — Continued
4. Remove three clamps (10) from three brackets (11), remove heater cover (12), control cover (13), and plenum cover
(14) from heater (2).
5. Remove five screws (18), lockwashers (19), and plenum cover (20) from plenum body (21). Discard lockwashers.
6. Remove two clamps (22) and hose (23) on the air intake (24) of the heater (2) and inlet tube (25) in the plenum body (21).
NOTE
The plug is only used in the plenum body to seal off the opening if a Model A-20 Heater is being
used. Perform Step 7 only if you need to replace the gasket and plug.
7. Remove plug (26) from plenum body (21). Remove gasket (27) from inside bottom of the plenum body (21).
8. Remove clamp (28), plenum body (21), and seal (29) from heater (2).
9. Remove screw (15), washer (16), and wiring harness ground lead (17) from bracket (11).
0447 00-2
Change 1
TM 9-2350-247-20-3

10. Loosen clamp (7) securing heater exhaust pipe (6) to heater (4).
11. Remove screw (1), lockwasher (2), and ground strap (3) from heater (4). Discard lockwasher.
12. Loosen clamp (8). Remove plenum chamber (9) from heater (4).
13. Spread open heater cover (5) and pull end of heater away from cover to clear heater exhaust outlet. Remove heater (4).
0447 00-3 Change 1

TM 9-2350-247-20-3

14. Loosen two clamps (9). Separate exhaust pipe (5) and exhaust pipe (8) and adapter (10).
15. Loosen two screws (4), locknuts (1), and four washers (2). Remove exhaust hood (3) from upper exhaust pipe (5).
Discard locknuts.
16.. Remove screw (11), washer (12), two brackets (7), and upper exhaust pipe (5) from weld nut (6).
Change 1 0447 00-4

TM 9-2350-247-20-3

INSTALLATION
NOTE
If heater is Model 8460C, do Steps 1 - 10.
1. Remove heater controls cover (WP 0450 00).

2. Remove screw (1), washer (2), and blower lead 6 (3) from terminal board (4).
3. Remove four screws (5) and heater blower (6) from heater housing (7).
4. Remove grommet (8) from heater housing (7). Discard grommet.
0447 00-5 Change 1

TM 9-2350-247-20-3

5. Drill new hole (9) 19/32 inch (15 mm) into heater housing (7).
6. Install new grommet (8) in new 19/32 inch (15 mm) hole in heater housing (7).
7. Thread blower lead 6 (3) through new grommet AB (8) to terminal board (4). Secure with washer (2) and screw (1).
8. Install heater blower (6) on heater housing (7) with four screws (5).
9. Cover old opening (10) with rubber adhesive tape.
10. Install heater controls cover (WP 0450 00).
Change 1 0447 00-6

TM 9-2350-247-20-3

11. Install exhaust hood (1) on upper exhaust pipe (2) with two new locknuts (3), four washers (4), and screws (5).
12. Install exhaust pipes (2), and (6) and adapter (7). Secure with two clamps (8).
0447 00-7 Change 1

TM 9-2350-247-20-3

13. Remove five screws (1), lockwashers (2), and plenum cover (3) from plenum body (4).
14. Install seal (5) and plenum body (4) on heater (7). Secure with clamp (6).
15. Install two clamps (8) and hose (9) on the air intake (10) of the heater (7) and inlet tube (12) in the plenum body (4).
WARNING
NOTE
The plug is only used in the plenum body to seal off the opening if a Model A-20 Heater is being
used. Perform Step 16 only if the gasket and plug have been removed.
16. Install plug (11) in plenum body (4). Place adhesive on gasket (13) and install on inside bottom of plenum body (4)
to seal off opening.
17. Install plenum cover (3) on plenum body (4) and secure with five screws (1) and new lockwashers (2).
Change 1 0447 00-8

TM 9-2350-247-20-3

NOTE
Install a new seal on the Model A-20, MIL-PRF-62550/2A heater before installing the plenum
chamber (9) on it. See TM-9-2540-207-14&P for procedures.
18. Install plenum chamber (9) on heater (11). Secure with clamp (12).
19. Install plenum cover (13), controls cover (14), and heater cover (15) on heater (11).
20. Place heater (11) on three brackets (16). Secure with three clamps (17).
21 Install ground strap (18) on heater (11) with new lockwasher (19) and screw (20).
0447 00-9
Change 1
TM 9-2350-247-20-3

22. Install exhaust pipe (2) and exhaust pipe (6) on heater (11) with clamp (21).
23. Install upper exhaust pipe (2) and two brackets (22) on weld nut (23) with two washers (24) and screws (25).
24. Install wiring harness ground lead (26) to bracket (16) with washer (27) and screw (28).
25. Connect fuel hose (29) to heater (11). Secure outlet hose (30) to plenum chamber (9) with clamp (31).
26. Install intake hose (32) on intake duct (10) with clamp (33).
27. Connect wiring harness (34) to heater (11).
1. Install heater exhaust pipe guard (WP 0455 00).
4. Check heater for proper operation.
END OF TASK
0447 00-10
Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP (KIT I) 0448 00

(M548A1)

INITIAL SETUP:

Unit See your -10
Materials/Parts
Sealing compound (WP 0542 00, Item 33) Engine stopped (see your -10)
REMOVAL
1. Remove pump circuit 402 lead (1) from heater wiring harness.
2. Remove hose (2) from nipple (3) in tee (4). Remove nipple from tee. Remove tee from fuel pump (5).
3. Remove hose (6) from elbow (7) on fuel pump (5). Remove elbow from fuel pump.
4. Remove two nuts (8), four lock washers (9), two screws (10), fuel pump (5), and capacitor (11) from bracket (12).
0448 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP (KIT I) (M548A1) — 0448 00

Continued
INSTALLATION
NOTE
1. Install fuel pump (5) and capacitor (11) on bracket (12) with two screws (10), four new lock washers (9), and two
nuts (8).
2. Install elbow (7) and tee (4) in fuel pump (5). Connect hose (6) to elbow (7).
3. Install nipple (3) in tee (4). Connect hose (2) to nipple.
4. Connect fuel pump circuit 402 lead (1) to heater wiring harness.
END OF TASK
0448 00-2
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP AND 0449 00

FUEL FILTER (KIT II OR III) (M548A1)
INITIAL SETUP:

Unit Unit Mechanic

Suitable Container
Equipment Condition
Wiping rags (WP 0542 00, Item 45) Battery negative lead disconnected (WP 0292 00)
Packing, preformed (4)
REMOVAL
NOTE
Use suitable container to hold fuel still in fuel lines and heater components. Install covers on
disconnected fuel lines, tubes, and heater components during maintenance. Use tape, cloth,
cardboard, or any appropriate material to prevent damage to components or accidental fuel
spills.
0449 00-1
Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER FUEL PUMP AND FUEL 0449 00

FILTER (KIT II OR III) (M548A1) — Continued
1. Remove pump circuit 402 lead (1) from heater wiring harness.
2. Remove hose (2) from elbow (3) and hose (4) from elbow (5). Remove elbows (3) and (5) from couplings (5.1) and
(5.2). Remove couplings (5.1) and (5.2) from fuel pump (6).
3. Remove two screws (7), lockwashers (8), fuel pump (6), and capacitor (9) from rear power plant compartment bulkhead.
Discard lockwashers.
4. Remove hose (10) from outlet elbow (12) and hose (4) from inlet elbow (12). Remove two elbows (12) from fuel
filter (11).
5. Remove two nuts (13), screws (14), lockwashers (15), flat washers (16), and fuel filter (11) from bracket (17). Discard
lockwashers.
6. Remove two plugs (18) and packings (20) from fuel filter (11). Discard packings.
7. Remove two adapters (19) and packings (20) from fuel filter (11). Discard packings.
8. Remove two screws (21), lockwashers (22), flat washers (23), and bracket (17) from bulkhead. Discard lockwashers.
0449 00-2
Change 1
TM 9-2350-247-20-3

INSTALLATION
WARNING
NOTE
1. Install fuel pump (6) and capacitor (9) on power plant bulkhead with two new lockwashers (8) and screws (7).
2. Install two couplings (5.1) and (5.2) on fuel pump (6).
0449 00-3
Change 1
TM 9-2350-247-20-3

3. Install elbows (3) and (5) on fuel pump (6). Install hose (4) on elbow (5) and hose (2) on elbow (3).
4. Connect fuel pump circuit 402 lead (1) to heater wiring harness.
5. Install bracket (17), two flat washers (23), new lockwashers (22) and screws (21) on bulkhead.
6. Install two new packings (20) and plugs (18) on fuel filter (11).
7. Install two new packings (20) and adapters (19) on fuel filter (11).
8. Install fuel filter (11), two flat washers (16), new lockwashers (15), screws (14), and two nuts (13), on bracket (17).
9. Install two elbows (12) on adapters (19). Install hoses (4) and (10) on fuel filter (11).
3. Check heater fuel pump and filter for leaks and proper operation.
END OF TASK
0449 00-4
Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER CONTROLS COVER 0450 00

(M548A1)
INITIAL SETUP:

Unit See your -10

Top left access grille removed (WP 0390 00)
REMOVAL
1. For Kit I, turn fastener (1) to left and remove cover (2) from heater (3).
0450 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER CONTROLS COVER (M548A1) — 0450 00

Continued
2. For Kits II and III, open two clamps (1) and remove insulated cover (2) from heater (3).
INSTALLATION
1. For Kit I, install cover (2) over controls and secure to heater (3) by turning fastener (1) to right.
0450 00-2
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER CONTROLS COVER (M548A1) — 0450 00

Continued
2. For Kits II and III, install insulated cover (2) over controls and secure to heater (3) with two clamps (1).
END OF TASK
0450 00-3/4 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS 0451 00

(M548A1)
INITIAL SETUP:

Unit
See your -10
Grommet Engine stopped (see your -10)
Lock washer (2)
Lock washer (9)
Personnel Required Battery negative lead disconnected (WP 0292 00)
Unit Mechanic Top left access grille removed (WP 0390 00)
0451 00-1
TM 9-2350-247-20-3

Continued
REMOVAL
1. Remove wiring harness connector (1) from control box receptacle (2).
2. Remove wiring harness connector (3) from heater receptacle (4).
3. Remove screw (5), two lock washers (6), and wiring harness ground lead (7) from hull. Discard lock washers.
4. Remove wiring harness circuit 402 lead (8) from fuel pump lead (9).
5. Remove nine screws (10), lock washers (11), clamps (12), and wiring harness (13) from nine weld nuts (14). Discard
lock washers.
6. Remove wiring harness (13) from carrier. Remove grommet (15) from wiring harness. Discard grommet.
0451 00-2
TM 9-2350-247-20-3

Continued
INSTALLATION
1. Install new grommet (1) on wiring harness (2).
2. Install wiring harness (2) on nine weld nuts (3) in carrier with nine clamps (4), new lock washers (5), and screws (6).
3. Install circuit 402 lead (7) on fuel pump lead (8).
4. Install wiring harness ground lead (9) on hull with two new lock washers (10) and screw (11).
5. Install wiring harness connector (12) on heater receptacle (13).
6. Install wiring harness connector (14) on control box receptacle (15).
3. Check heater wiring harness for proper operation.
END OF TASK
0451 00-3/4 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES 0452 00

(KIT I) (M548A1)
INITIAL SETUP:

Tools and Special Tools Battery negative lead disconnected (WP 0292 00)
General Mechanic’s Tool Kit (WP 0541 00, Item 57) Top left access grille removed (WP 0390 00)
Cab left center floor plate raised (WP 0394 00)
Personnel Required
Unit Mechanic
References
See your -10
0452 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT I) (M548A1) 0452 00
— Continued
REMOVAL
1. Remove two clamps (1) and intake hose (2) from air duct (3) and elbow (4).
2. Remove four plugs (5) from air duct (3) access holes. Remove four screws (6) and air duct from cab heater (7).
3. Remove four screws (8), washers (9), and elbow (4) from power plant access cover (10).
0452 00-2
TM 9-2350-247-20-3
— Continued
4. Remove four screws (1), washers (2), four clamps (3), and two nuts (4) securing hose (5) to two weld nuts (6), brackets
(7), heater plenum (8) and adapter (9).
5. Remove two clamps (10) and outlet hose (11) from heater plenum (8) and outlet duct (12).
6. Remove two clamps (13) and hose (14) from adapter (9) and defroster manifold hose (15).
7. Remove two screws (16) and adapter (9) from hull.
8. Remove five nuts (17), washers (18), screws (19), and defroster manifold hose (15) from hull.
0452 00-3
TM 9-2350-247-20-3
— Continued
INSTALLATION
1. Install defroster manifold hose (1) on hull with five screws (2), washers, (3), and nuts (4).
2. Install adapter (5) on hull with two screws (6).
3. Install hose (7) on defroster manifold hose (1) and adapter (5) with two clamps (8).
4. Install hose (9) on outlet duct (10) and heater plenum (11) with two clamps (12).
5. Install hose (13) on two brackets (14), weld nuts (15), heater plenum (11), and adapter (5) with four clamps (16), screws
(17), washers (18), and two nuts (19).
0452 00-4
TM 9-2350-247-20-3
— Continued
6. Install elbow (1) on power plant access cover (2) with four washers (3) and screws (4).
7. Install air duct (5) on cab heater (6) with four screws (7). Install four plugs (8) in air duct access holes.
8. Install hose (9) on air duct (5) and elbow (1) with two clamps (10).
3. Check heater air ducts and hoses for leaks and proper operation.
5. Lower cab left center floor plate (WP 0394 00).
END OF TASK
0452 00-5/6 blank

TM 9-2350-247-20-3

(KIT II) (M548A1)
INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Lock nut
Lock nut Engine stopped (see your -10)
Lock nut Carrier blocked (see your -10)
Lock nut (4) Top left access grille removed (WP 0390 00)
Lock washer (4) Cab left center floor plate raised (WP 0394 00)
0453 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS AND HOSES (KIT II) (M548A1) 0453 00
— Continued
REMOVAL
1. Remove two clamps (1) and intake hose (2) from adapter (3) and intake duct (4).
2. Remove four nuts (5), washers (6), screws (7), grille (8), and adapter (3) from driver’s seat rear bulkhead.
3. Remove two clamps (9) and hose (10) from tee (11) and elbow (12).
4. Remove two nuts (13), washers (14), screws (15), elbow (12), and deflector (16) from battery well bulkhead.
0453 00-2
TM 9-2350-247-20-3
— Continued
5. Remove two screws (1), lock washers (2), lock nut (3), and clamp (4) from weld nut (5) and driver’s floor. Discard lock
washers and lock nut.
6. Remove two clamps (6) and hose (7) from adapter (8) and tee (9).
7. Remove two screws (10), lock washers (11), clamp (12), and bracket (13) from two weld nuts (14). Discard lock washers.
8. Remove two clamps (15) and hose (16) from plenum (17) and tee (9).
0453 00-3
TM 9-2350-247-20-3
— Continued
9. Remove lock nut (18), two washers (19), screw (20), clamp (21), and left defroster hose (22) from hull. Discard lock nut.
10. Remove two clamps (23). Disconnect left defroster hose (22) from left defroster duct (24) and heat regulator (25).
11. Remove two clamps (26). Disconnect right defroster hose (27) from right defroster duct (28) and heat regulator (25).
12. Remove four lock nuts (29), eight washers (30), four screws (31), and left defroster duct (24) and right defroster duct
(28) from hull. Discard lock nuts.
0453 00-4
TM 9-2350-247-20-3
— Continued
13. Remove 11 screws (1), washers (2), and heat distributor cover (3) from heat distributor (4).
14. Remove four screws (5), washers (6), and heat regulator (7) from heat distributor (4).
15. Remove two screws (8), washers (9), and adapter (10) from heat regulator (7).
16. Remove three screws (11), washers (12), and heat distributor (4) from hull.
17. Remove two screws (13) and heat regulator cover (14) from heat regulator (7).
18. Remove lock nut (15), spring (16), and valve (17) from regulator (7). Discard lock nut.
0453 00-5
TM 9-2350-247-20-3
— Continued
INSTALLATION
1. Install valve (17) in heat regulator (7) with spring (16) and new lock nut (15).
2. Install heat regulator cover (14) on heat regulator (7) with two screws (13).
3. Install heat distributor (4) on hull with three washers (12) and screws (11).
4. Install adapter (10) on heat regulator (7) with two washers (9) and screws (8).
5. Install heat regulator (7) on heat distributor (4) with four washers (6) and screws (5).
6. Install heat distributor cover (3) on heat distributor (4) with 11 washers (2) and screws (1).
0453 00-6
TM 9-2350-247-20-3
— Continued
7. Install right defroster duct (1) and left defroster duct (2) in hull with four screws (3), eight washers (4), and four new lock
nuts (5).
8. Connect right defroster hose (6) to right defroster duct (1) and heat regulator (7). Secure with two clamps (8).
9. Connect left defroster hose (9) to left defroster duct (2) and heat regulator (7). Secure with two clamps (10).
10. Install left defroster hose (9) on hull with clamp (11), screw (12), washer (13), and new lock nut (14).
0453 00-7
TM 9-2350-247-20-3
— Continued
11. Install hose (15) and two clamps (16) on plenum (17) and tee (18).
12. Install bracket (19), clamp (20), two new lock washers (21), and screws (22) on two weld nuts (23).
13. Install hose (24) and two clamps (25) on adapter (26) and tee (18).
14. Install clamp (27), two new lock washers (28), screws (29), and new lock nut (30) onto weld nut (31) and driver’s floor.
0453 00-8
TM 9-2350-247-20-3
— Continued
15. Install deflector (1), elbow (2), two screws (3), washers (4), and nuts (5) to battery well bulkhead.
16. Install hose (6) and two clamps (7) to tee (8) and elbow (2).
17. Install adapter (9), grille (10), four screws (11), washers (12), and nuts (13) to driver’s seat rear bulkhead.
18. Install intake hose (14) and two clamps (15) to adapter (9) and intake duct (16).
5. Install cab left center floor plate (WP 0394 00).
END OF TASK
0453 00-9/10 blank

TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER AIR DUCTS 0454 00

AND HOSES (KIT III) (M548A1)
INITIAL SETUP:

Unit See your -10
TM-9-2540-207-14&P
Materials/Parts
Locknut
Top left access grill removed (WP 0390 00)
Locknut (5)
Cab left center floor plate raised (WP 0394 00)
Lockwasher (4)
Lockwasher (6)
Personnel Required
Unit Mechanic
0454 00-1
Change 1
TM 9-2350-247-20-3

(KIT III) (M548A1) — Continued
REMOVAL
1. Remove two clamps (1) and intake hose (2) from adapter (3) and intake duct (4).
NOTE
Step 2 is used with new heater Model A-20, MIL-PRF–62550/2A only.
2. Remove plug (4.1) from intake duct (4).

3. Remove four nuts (5), washers (6), screws (7), grill (8), and adapter (3) from driver’s seat rear bulkhead.
4. Remove two clamps (9) and hose (10) from tee (11) and elbow (12).
5. Remove two nuts (13), washers (14), screws (15), elbow (12), and deflector (16) from battery well bulkhead.
0454 00-2
Change 1
TM 9-2350-247-20-3

6. Remove two screws (1), lockwashers (2), locknut (3), and clamp (4) from weld nut (5) and driver’s floor. Discard
lockwashers and locknut.
7. Remove two clamps (6) and hose (7) from adapter (8) and tee (9).
8. Remove two screws (10), lockwashers (11), clamp (12), and bracket (13) from two weld nuts (14). Discard lockwashers.
9. Remove two clamps (15) and hose (16) from plenum (17) and tee (9).
0454 00-3
Change 1
TM 9-2350-247-20-3

10. Remove two clamps (18) and left defroster hose (19) from housing (20) and left defroster duct (21).
11. Remove locknut (22), two washers (23), screw (24), clamp (25), and hose (19) from hull. Discard locknut.
12. Remove two clamps (26) and right defroster hose (27) from right defroster duct (28) and housing (20).
13. Remove four locknuts (29), eight washers (30), four screws (31), and left defroster duct (28) and right defroster duct
(21) from hull. Discard locknuts.
0454 00-4
Change 1
TM 9-2350-247-20-3

14. Remove 11 screws (1), washers (2), shield (3), and distributor cover (4) from distributor duct (5).
15. Remove three screws (6), washers (7), and distributor duct (5) from hull.
16. Remove four screws (8), washers (9), and housing (10) from distributor duct (5).
17. Disconnect circuit 346 lead from right defroster fan (11) and circuit 347 lead from left defroster fan (12).
18. Remove six screws (13), lockwashers (14), and right defroster fan (11) and left defroster fan (12) from housing (10).
Discard lockwashers.
19. Remove two screws (15), washers (16), and adapter (17) from housing (10).
0454 00-5
Change 1
TM 9-2350-247-20-3

INSTALLATION
1. Install adapter (17) on housing (10) with two washers (16) and screws (15).
2. Install left defroster fan (12) and right defroster fan (11) on housing (10) with six new lockwashers (14) and screws (13).
3. Connect circuit 347 lead to left defroster fan (12) and circuit 346 lead to right defroster fan (11).
4. Install housing (10) on distributor duct (5) with four washers (9) and screws (8).
5. Install distributor duct (5) on hull with three washers (7) and screws (6).
6. Install distributor cover (4) and shield (3) on distributor duct (5) with 11 washers (2) and screws (1).
0454 00-6
Change 1
TM 9-2350-247-20-3

7. Install right defroster duct (1) and left defroster duct (2) in hull with four screws (3), eight washers (4), and four new
locknuts (5).
8. Connect right defroster hose (6) to right defroster duct (1) and housing (7). Secure with two clamps (8).
9. Connect left defroster hose (9) to left defroster duct (2) and housing (7). Secure with two clamps (10).
10. Install hose (9) on hull with clamp (11), screw (12), two washers (13), and new locknut (14).
0454 00-7
Change 1
TM 9-2350-247-20-3

11. Install hose (15) and two clamps (16) on plenum (17) and tee (18).
12. Install bracket (19), clamp (20), two new lockwashers (21), and screws (22) on two weld nuts (23).
13. Install hose (24) and two clamps (25) on adapter (26) and tee (18).
14. Install clamp (27), two new lockwashers (28), screws (29), and new locknut (30) on weld nut (31) and driver’s floor.
0454 00-8
Change 1
TM 9-2350-247-20-3

15. Install deflector (1), elbow (2), two screws (3), washers (4), and nuts (5) on battery well bulkhead.
16. Install hose (6) and two clamps (7) on tee (8) and elbow (2).
17. Install adapter (9), grill (10), four screws (11), washers (12), and nuts (13) on driver’s seat rear bulkhead.
NOTE
Step 18 is used with new heater Model-20, MIL-PRF-62550/2A only.
18. Install plug (16.1) on intake duct (16).

19. Install intake hose (14) and two clamps (15) on adapter (9) and intake duct (16).
3. Check cab heater for leaks and proper operation.
5. Install cab left center floor plate (WP 0394 00).
END OF TASK
0454 00-9/10 blank

Change 1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST GUARD 0455 00

(M548A1)
INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Lock nut (6)
Left side intake grille removed (WP 0390 00)
0455 00-1
TM 9-2350-247-20-3
REPLACE VEHICLE COMPARTMENT HEATER EXHAUST GUARD (M548A1) — 0455 00

Continued
REMOVAL
WARNING
Do not work on hot exhaust pipes. Personnel could be burned.
1. Loosen clamp (1) securing upper exhaust pipe (2) and remove upper exhaust pipe with guard (3) attached.
2. Loosen nut (4) and slide hood (5) off upper exhaust pipe (2).
3. Loosen six screws (6).
4. Remove 6 screws (7), lock nuts (8), and 12 washers (9). Discard lock nuts.
5. Slide exhaust guard (3) off exhaust pipe (2) from bottom.
0455 00-2
TM 9-2350-247-20-3

Continued
6. Remove six screws (6), washers (10), and three guard brackets (11).
NOTE
Mark upper exhaust pipe (2) 5 1/2 inch and 25 inch (13.97 cm and 63.5 cm) from bottom to
indicate position of bracket clamps (13, 16).
7. Remove U-bolt (12) from bracket clamp (13) by removing two lock nuts (14) and washers (15). Discard lock nuts.
8. Disassemble two bracket clamps (16) by removing two screws (17), lock nuts (18), and four washers (19). Discard lock
nuts.
0455 00-3
TM 9-2350-247-20-3

Continued
INSTALLATION
NOTE
Be sure to install bracket clamp (2) and bracket clamp (6) so that guard brackets are attached
above top clamp and below bottom clamp. Bracket clamp screws (7) should show through holes
in exhaust guard.
1. Install U-bolt (1) and bracket clamp (2) with two new lock nuts (3) and washers (4) to upper exhaust pipe (5) just above 5
1/2 inch (13.97 cm) mark.
2. Assemble two bracket clamps (6) with two cap screws (7), new lock nuts (8), and four washers (9) to upper exhaust pipe
(5) just above 25 inch (63.5 cm) mark.
3. Install three guard brackets (10) with six screws (11) and washers (12). Do not tighten screws.
4. Slide exhaust guard (13) onto exhaust pipe (5) from bottom of exhaust pipe.
5. Install 6 screws (14), 12 washers (15), and 6 new lock nuts (16).
6. Secure upper exhaust pipe (5) with clamp (17).
0455 00-4
TM 9-2350-247-20-3

Continued
CAUTION
Do not allow exhaust to blow on canvas as fire could result.
7. Position hood (18) on upper exhaust pipe (5), with wide area forward and tighten nut (19).
1. Install left side intake grille (WP 0390 00).
END OF TASK
0455 00-5/6 blank

TM 9-2350-247-20-3
REPLACE FIBERGLASS CAB COVER 0456 00

INITIAL SETUP:

Unit See your -10

Lock nut (16)
Personnel Required
Unit Mechanic
Helper (H)
0456 00-1
TM 9-2350-247-20-3
REPLACE FIBERGLASS CAB COVER — Continued 0456 00
REMOVAL
1. Remove 8 screws (1), spacers (2), grommets (3), lock nuts (4), and 16 washers (5) that secure fiberglass cab cover (6),
front seal (7), and 2 pads (8) to windshield frame (9). Discard lock nuts.
2. Remove 8 screws (10), 7 spacers (11), and large spacer (12). Remove 8 grommets (13), lock nuts (14), and 16 washers
(15) that secure fiberglass cab cover (6), rear seal (16) and 2 side seals (17) to transverse beam (18). Discard lock nuts.
NOTE
Lifting fiberglass cab cover on or off carrier is a two-person job.
3. Remove fiberglass cab cover (6), front seal (7), rear seal (16), and two side seals (17) from carrier. Have helper assist.
Check seals for cracks and wear. Replace seals if necessary.
INSTALLATION
1. Place rear seal (16) and two side seals (17) on transverse beam (18). Place front seal (7) and two pads (8) on windshield
frame (9).
2. Place fiberglass cab cover (6) on carrier.
3. Secure front seal (7), 2 pads (8), and fiberglass cab cover (6) on windshield frame (9) with 8 spacers (2), grommets (3),
screws (1), new lock nuts (4), and 16 washers (5).
4. Secure rear seal (16), 2 side seals (17), and fiberglass cab cover (6) on transverse beam (18) with 7 spacers (11), large
spacer (12), 8 grommets (13), 16 washers (15), 8 screws (10), and new lock nuts (14).
END OF TASK
0456 00-2
TM 9-2350-247-20-3
REPLACE FIBERGLASS MACHINE GUN HATCH COVER 0457 00

INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
Preformed packing Engine stopped (see your -10)
REMOVAL
1. Remove nut (1), two washers (2), preformed packing (3), retainer (4), and screw (5) from cab cover (6). Discard
preformed packing.
2. Unhook spring (7) in hatch cover (8). Remove spring through slit in cover.
3. Remove hatch cover (8) from cab cover (6).
INSTALLATION
1. Insert spring (7) in hatch cover (8) through slit in cover.
2. Place hatch cover (8) on cab cover (6). Secure with screw (5), two washers (2), new preformed packing (3), retainer (4),
and nut (1).
END OF TASK
0457 00-1/2 blank

TM 9-2350-247-20-3
REPLACE CAB WINDOWS 0458 00

INITIAL SETUP:

Unit See your -10
REMOVAL
1. Remove two side filler seals (1) from two side window seals (2). Remove two rear filler seals (3) from rear window
seals (4).
2. Remove two side window seals (2) and side windows (5) from fiberglass cab cover (7).
3. Remove two rear window seals (4) and rear windows (6) from fiberglass cab cover (7).
0458 00-1
TM 9-2350-247-20-3
REPLACE CAB WINDOWS — Continued 0458 00
INSTALLATION
1. Install two side window seals (2) in fiberglass cab cover (7).
2. Install two side windows (5) in two side window seals (2). Secure with two side filler seals (1).
3. Install two rear window seals (4) in fiberglass cab cover (7).
NOTE
If carrier has a breather tube on rear window, install window with tube at bottom.
4. Install two rear windows (6) in two rear window seals (4). Secure with two rear filler seals (3).
END OF TASK
0458 00-2
TM 9-2350-247-20-3
REPLACE LOWER CAB INSULATION 0459 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Insulation Engine stopped (see your -10)
REMOVAL
NOTE
Remove lower cab insulation only if inspection shows replacement is needed. These instructions
are for removal of damaged panels or damaged areas of panels.
1. Remove as much old damaged insulation as you can by scraping. Make edges even. Cut patch to fit.
2. Remove remaining insulation and dried adhesive with cleaning compound.
INSTALLATION
1. Trim new insulation to fit. If panel to be installed is large, cut it into squares of about 3 feet (1 meter).
2. Spray or swab cleaning compound on back of insulation to activate adhesive.
3. Allow 10 to 15 seconds for adhesive to become tacky. Press insulation firmly into place at once.
END OF TASK
0459 00-1/2 blank

TM 9-2350-247-20-3
REPLACE CLOTH SEAT COVERS 0460 00

INITIAL SETUP:

Unit See your -10
FM 10-16
0460 00-1
TM 9-2350-247-20-3
REPLACE CLOTH SEAT COVERS — Continued 0460 00
REMOVAL
1. Detach right seat cover strap (1) and center seat cover strap (2). Remove straps from seat cover (3) and seat cover (4) and
hull.
2. Detach two right tie down straps (5). Remove right rod (6) from right seat cover (3).
3. Detach three center tie down straps (7). Remove center rod (8) from center seat cover (4).
4. Remove upper rod (9), right seat cover (3), and center seat cover (4) as a unit. Remove right seat cover and center seat
cover from upper rod.
5. Remove two right tie down straps (5) and three center tie down straps (7).
6. Untie cord (10). Remove three screws (11) and washers (12). Remove driver’s seat cover (13) from driver’s seat (14).
0460 00-2
TM 9-2350-247-20-3
REPLACE CLOTH SEAT COVERS — Continued 0460 00
INSTALLATION
1. Place driver’s seat cover (1) on driver’s seat (2). Secure with cord (3), three washers (4), and screws (5).
2. Install two right tie down straps (6) and three center tie down straps (7) on hull.
3. Place center seat cover (8) and right seat cover (9) on upper rod (10). Install rod and covers on hull as a unit.
4. Install right seat cover strap (11) and center seat cover strap (12). Make sure right seat cover (9) and center seat cover (8)
are placed right. Secure straps.
5. Install right rod (13) in right seat cover (9). Secure cover with two right tie down straps (6).
6. Install center rod (14) in center seat cover (8). Secure cover with three center tie down straps (7).
END OF TASK
0460 00-3/4 blank

TM 9-2350-247-20-3
REPLACE THERMAL DOOR WINDOWS 0461 00


INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
Rubber adhesive tape (WP 0542 00, Item 32) Engine stopped (see your -10)
REMOVAL
NOTE
Before removing thermal panels, look for cracks and scratches. Check sealing tape for wear
and looseness. If panels are scratched enough to affect vision, replace them.
1. Remove front thermal panel (1) and rear thermal panel (2) from front window glass (3) and rear window glass (4).
2. Remove rubber adhesive tape from front window glass (3), rear window glass (4), front thermal panel (1), and rear
thermal panel (2). Discard rubber adhesive tape.
0461 00-1
TM 9-2350-247-20-3
REPLACE THERMAL DOOR WINDOWS — Continued 0461 00
INSTALLATION
1. Remove protective backing from new rubber adhesive tape. Place tape on front window glass (3) and rear window
glass (4).
2. Place front thermal panel (1) and rear thermal panel (2) on front window glass (3) and rear window glass (4). Press
securely in place.
END OF TASK
0461 00-2
TM 9-2350-247-20-3
REPLACE CARGO AREA HEATER AND CONTROL BOX MOUNTING 0462 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Gasket (2) Equipment Condition
Lock washer Carrier blocked (see your -10)
Lock washer (3) Battery negative lead(s) disconnected (WP 0292 00)
0462 00-1
TM 9-2350-247-20-3
REPLACE CARGO AREA HEATER AND CONTROL BOX MOUNTING — Continued 0462 00
REMOVAL
1. Disconnect fuel hose elbow (1) from adapter (2).
2. Disconnect wiring harness (3) from control box (4) and cargo area heater (5).
3. Remove screw (6), lock washer (7), and ground lead (8) from control box (4). Discard lock washer.
4. Remove two screws (9), washers (10), support (11), and cargo area heater (5) from cargo door (12).
0462 00-2
TM 9-2350-247-20-3
5. Loosen clamp (1). Remove two clamps (2) and cargo area heater (3) with control box (4) from support (5) and exhaust
pipe (6).
6. Remove three screws (7), lock washers (8), and heat diffuser (9) from cargo area heater (3). Discard lock washers.
7. Remove two lock nuts (10), washers (11), mounts (12), and control box (4) from bracket (13). Discard lock nuts.
0462 00-3
TM 9-2350-247-20-3
8. Remove four lock nuts (14), eight washers (15), four screws (16), exhaust pipe (6), two gaskets (17), and plate (18) from
support (5). Discard gaskets and lock nuts.
9. Remove two lock nuts (19), four washers (20), two screws (21), and two curtain guards (22) from support (5). Discard
lock nuts.
10. Loosen clamp (23). Remove moisture trap (24) from exhaust pipe (6).
0462 00-4
TM 9-2350-247-20-3
INSTALLATION
1. Install moisture trap (1) on exhaust pipe (2). Secure with clamp (3).
2. Install two new gaskets (4), plate (5), and exhaust pipe (2). Secure with four screws (6), eight washers (7), and four new
lock nuts (8).
3. Install two curtain guards (9). Secure with two screws (10), four washers (11), and two new lock nuts (12).
4. Install control box (13) on bracket (14). Secure with two washers (15) and new lock nuts (16).
0462 00-5
TM 9-2350-247-20-3
5. Install cargo area heater (17) and control box (13), assembled on control box support (18), on support (19). Secure with
two mounting clamps (20).
6. Connect exhaust pipe (2) to cargo area heater (17). Secure with clamp (21).
7. Install hot air diffuser (22) on bottom of cargo area heater (17). Secure with three new lock washers (23) and screws (24).
0462 00-6
TM 9-2350-247-20-3
8. Install assembled cargo area heater (1) and support (2) on cargo door (3). Make sure two bracket pins engage holes in
top of cargo door. Secure with two washers (4) and screws (5).
9. Connect wiring harness (6) to cargo area heater (1) and control box (7).
10. Connect ground lead (8) to control box (7). Secure with new lock washer (9) and screw (10).
11. Connect fuel hose elbow (11) to adapter (12).
3. Check cargo area heater and control box mounting for proper operation.
END OF TASK
0462 00-7/8 blank

TM 9-2350-247-20-3
REPLACE CARGO AREA HEATER FUEL LINES, FITTINGS AND SHIELDS 0463 00
INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Antiseize compound (WP 0542 00, Item 6)
Lock nut (11) Battery negative lead(s) disconnected (WP 0292 00)
Preformed packing Top left access grille removed (WP 0390 00)
Excess fuel drained (see your -10)
REMOVAL
NOTE
Cap all fuel lines.
1. Disconnect rear fuel hose elbow coupling (1) from adapter (2). Remove adapter from cargo area heater (3).
0463 00-1
TM 9-2350-247-20-3
REPLACE CARGO AREA HEATER FUEL LINES, FITTINGS AND SHIELDS — Continued 0463 00
2. Disconnect fuel hose (1) from rear fuel hose (2) at coupling (3).
3. Remove three lock nuts (4), washers (5), screws (6), three lead clamps (7), three hose clamps (8), and rear fuel hose (2)
from three clips (9). Discard lock nuts.
4. Disconnect fuel hose (1) from elbow (10).
5. Remove three screws (11), washers (12), and cover (13) from bulkhead protector (14).
6. Remove fuel hose (1) running through guard (15).

7. Disconnect fuel hose (16) from elbow (10) and elbow (17).
8. Remove nut (18) and elbow (10) from bulkhead.
9. Disconnect fuel tube (19) from elbow (20) and adapter (21).
10. Remove four clamps (22), two screws (23), lock nuts (24), and tube (19) from bulkhead. Discard lock nuts.
11. Remove adapter (21) and preformed packing (25) from fuel manifold block (26). Discard preformed packing.
0463 00-2
TM 9-2350-247-20-3
12. Remove two elbows (17 and 20) and unions (27) from fuel pump (28).
WARNING
Heat shield insulation may contain asbestos. Inhaled asbestos dust can cause permanent lung
damage. Wear a filter mask approved for asbestos protection and rubber gloves during
handling of asbestos. Wash skin and clothing with soap and water after handling asbestos.
Dispose of asbestos material in accordance with approved hazardous waste disposal procedures.
13. Remove 4 lock nuts (29), screws (30), 12 washers (31), and shield (32) from cargo cover. Discard lock nuts.
14. Remove six lock nuts (33), washers (34), screws (35), clamps (36), and guard (15) from six clamps (37). Discard lock
nuts.
INSTALLATION
1. Apply a light coat of sealing compound to tapered pipe fittings.
2. Apply a light coat of antiseize compound to straight threaded fittings.
0463 00-3
TM 9-2350-247-20-3
3. Secure guard (1) to six clamps (2) with six clamps (3), screws (4), washers (5), and new lock nuts (6).
WARNING
Heat shield insulation may contain asbestos. Inhaled asbestos dust can cause permanent lung
damage. Wear a filter mask approved for asbestos protection and rubber gloves during
handling of asbestos. Wash skin and clothing with soap and water after handling asbestos.
Dispose of asbestos material in accordance with approved hazardous waste disposal procedures.
4. Install shield (7) on cargo cover. Secure with 12 washers (8), 4 screws (9), and new lock nuts (10).
5. Install two unions (11) on fuel pump (12).
6. Install two elbows (13 and 14) in two unions (11).
7. Install new preformed packing (15) and adapter (16) in fuel manifold block (17).
8. Connect fuel tube (18) to adapter (16) and elbow (13).
0463 00-4
TM 9-2350-247-20-3
9. Secure fuel tube (18) to bulkhead with four clamps (19), two new lock nuts (20), and screws (21).
10. Install elbow (22) in bulkhead. Secure with nut (23).

11. Connect fuel hose (24) to elbow (14) and elbow (22).
12. Install cover (25) on bulkhead protector (26). Secure with three washers (27) and screws (28).
13. Install fuel hose (29) through guard (1). Connect hose to elbow (22) and coupling (30).
14. Secure rear fuel hose (31) and fuel hose (29) to three clips (32) with three lead clamps (33), hose clamps (34), screws
(35), washers (36), and new lock nuts (37).
0463 00-5
TM 9-2350-247-20-3
15. Screw adapter (1) into cargo area heater (2). Connect rear fuel hose elbow coupling (3) to adapter (1).
2. Start cargo area heater (see your -10).
3. Check cargo area heater for leaks and proper operation.
4. Stop cargo area heater (see your -10).
END OF TASK
0463 00-6
TM 9-2350-247-20-3
REPLACE CARGO AREA HEATER FUEL PUMP 0464 00

INITIAL SETUP:

Unit See your -10
REMOVAL
1. See (primary) vehicle compartment heater fuel pump for maintenance procedures (WP 0448 00 or WP 0449 00).
END OF TASK
0464 00-1/2 blank

TM 9-2350-247-20-3
REPLACE CARGO AREA HEATER WIRING HARNESS 0465 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Grommet
Lock washer (2) Battery negative lead(s) disconnected (WP 0292 00)
Top left access grille removed (WP 0390 00)
0465 00-1
TM 9-2350-247-20-3
REPLACE CARGO AREA HEATER WIRING HARNESS — Continued 0465 00
REMOVAL
NOTE
The vehicle compartment heater is an installed system in the M548A3. It is a kit in the M548A1.
1. Remove nut (1), and circuit 400C lead (2) of front wiring harness (3) from master switch (4).
2. Disconnect circuit 402C lead (5) of front wiring harness (3) from capacitor (6) on fuel pump (7).
3. Remove screw (8), lock washer (9), and ground lead (10) of front wiring harness (3) from fuel pump (7). Discard lock
washer.
4. Remove five lock nuts (11), screws (12), seven clamps (13), and front wiring harness (3) from battery box and bulkhead.
Discard lock nuts.
5. Remove grommet (14) from bulkhead and front wiring harness (3). Discard grommet.
0465 00-2
TM 9-2350-247-20-3
6. Remove lock nut (1), screw (2), and two clamps (3) securing front wiring harness (4) to clip (5). Discard lock nut.
7. Disconnect front wiring harness (4) from rear wiring harness (6).
8. Remove front wiring harness (4) from carrier through guard (7).
9. Disconnect rear wiring harness connector (8) from heater (9).
10. Disconnect rear wiring harness connector (10) and circuit 400C lead (11) from control box (12).
11. Remove screw (13), two lock washers (14), and rear wiring harness ground lead (15) from control box (12). Discard lock
washers.
12. Remove two lock nuts (16), washers (17), screws (18), four clamps (19), and rear wiring harness (6) from two clips (5).
Discard lock nuts.
0465 00-3
TM 9-2350-247-20-3
13. Remove six lock nuts (20), washers (21), screws (22), clamps (23), and guard (7) from six clamps (24). Discard lock
nuts.
14. Remove three screws (25), washers (26), and cover (27) from bulkhead protector (28).
0465 00-4
TM 9-2350-247-20-3
INSTALLATION
1. Install cover (1) on bulkhead protector (2). Secure with three washers (3) and screws (4).
2. Secure guard (5) to six clamps (6) with six clamps (7), screws (8), washers (9), and new lock nuts (10).
3. Install front wiring harness (11) through guard (5).
4. Secure front wiring harness (11) to clip (12) with clamp (13), screw (14), and new lock nut (15).
0465 00-5
TM 9-2350-247-20-3
5. Secure rear wiring harness (16) to two clips (12) with four clamps (17), two screws (18), washers (19), and new lock
nuts (20).
6. Secure rear wiring harness ground lead (21) to control box (22) with two new lock washers (23) and screw (24).
7. Connect rear wiring harness circuit 400C lead (25) and connector (26) to control box (22).
8. Connect rear wiring harness connector (27) to heater (28).
9. Connect rear wiring harness (16) to front wiring harness (11).
0465 00-6
TM 9-2350-247-20-3
10. Install new grommet (1) on front wiring harness (2) and in bulkhead.
11. Secure front wiring harness (2) to battery box and bulkhead with seven clamps (3), five screws (4), and new lock nuts (5).
12. Secure front wiring harness ground lead (6) to fuel pump (7) with new lock washer (8) and screw (9).
13. Connect circuit 402C lead (10) to capacitor (11) on fuel pump (7).
NOTE
The second circuit 400C is for the vehicle compartment heater, if installed.
14. Secure front wiring harness circuit 400C lead (12) with circuit 400C and circuit 6 to master switch (13) in battery box
with nut (14).
2. Start cargo area heater (see your -10).
3. Check cargo area heater for proper operation.
4. Stop cargo area heater (see your -10).
END OF TASK
0465 00-7/8 blank

TM 9-2350-247-20-3
REPLACE INSULATED CARGO COVERS 0466 00

INITIAL SETUP:

Unit See your -10
FM 10-16
0466 00-1
TM 9-2350-247-20-3
REPLACE INSULATED CARGO COVERS — Continued 0466 00
REMOVAL
1. Loosen four curtain straps (1) that secure curtains (2) to inside of cargo door (see your -10).
2. Remove front and rear pockets (3) from material handling kit beam.
3. Loosen four outside tiedown ropes (4) on sides and rear of carrier. Unhook ropes from tiedown hooks (5).
4. Loosen inside tiedown rope (6). Unhook rope from tiedown hooks (7) along bulkhead (8).
5. Unhook six web straps (9) that secure front and rear closure flaps closed.
6. Untie three ties (10) (at front and rear) on inside of cargo cover (11).
7. Untie nine cover tie ropes (12) that secure cargo cover (11) to four bows (13).
8. Remove cargo cover (11) from four bows (13).
0466 00-2
TM 9-2350-247-20-3
REPLACE INSULATED CARGO COVERS — Continued 0466 00
NOTE
Make sure cover is clean and dry when it is folded and stored. If it is dirty or wet, it could
mildew and rot.
9. To remove bows, if damaged, see (WP 0417 00).
INSTALLATION
1. To install bows, if removed, see (WP 0417 00).
2. Place cargo cover (1) over four bows (2). Place front and rear pockets over ends of material handling kit beam (3).
Escape hatch will be at right rear of carrier.
3. Secure cargo cover (1) to four bows (2) with nine cover tie ropes (4).
4. Fasten inside tiedown ropes (5) to inside tiedown hooks (6) on bulkhead (7). Pull rope until front flaps of cargo cover (1)
are in place. Tie rope securely.
5. Tuck tiedown rope ends between rope (5) and bulkhead (7).
6. Lower curtains (8). Fasten four curtain straps (9) to inside of cargo door (see your -10).
7. Tie three ties (10) (front and rear) on inside of cargo cover (1) to close flaps.
8. Fasten three web straps (11) (front and rear) on outside of cargo cover (1) to secure flaps.
9. Fasten four outside tiedown ropes (12) on sides and rear of carrier. Tie ropes securely to tiedown hooks (13).
10. Tuck tiedown rope ends between rope (12) and bulkhead (7).
END OF TASK
0466 00-3/4 blank

TM 9-2350-247-20-3
REPLACE ESCAPE HATCH COVER 0467 00

INITIAL SETUP:

Unit See your -10

Lock washer (15)
Personnel Required
Unit Mechanic
0467 00-1
TM 9-2350-247-20-3
REPLACE ESCAPE HATCH COVER — Continued 0467 00
REMOVAL
1. Unhook spring (1) and remove it through slit in hatch cover (2).
2. Remove hatch cover (2) from webbed cord (3).
3. Remove screw (4), washer (5), retainer (6), lock washer (7), and nut (8) from clamping ring (9), cargo cover (10), gasket
(11), and hatch cover frame (12). Discard lock washer.
4. Remove 14 screws (13), washers (14), lock washers (15), and nuts (16) from clamping ring (9), cargo cover (10), gasket
(11), and hatch cover frame (12). Separate hatch cover frame, gasket, canvas cover, and clamping ring. Discard lock
washers.
INSTALLATION
1. Place gasket (11) and cargo cover (10) between hatch cover frame (12) and clamping ring (9).
2. Secure hatch cover frame (12), gasket (11), cargo cover (10) to clamping ring (9) with screw (4), washer (5), retainer (6),
new lock washer (7), and nut (8).
3. Secure hatch cover frame (12), gasket (11), cargo cover (10) to clamping ring (9) with 14 screws (13), washers (14), new
lock washers (15), and nuts (16).
4. Place hatch cover (2) and webbed cord (3) over hatch cover frame (12). Hook ends of spring together.
5. Install spring (1) through slit in hatch cover (2).
END OF TASK
0467 00-2
TM 9-2350-247-20-3
REPLACE INSULATED COVER WINDOWS 0468 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Lock nut (18)
REMOVAL
1. Secure window curtains in rolled position to expose window to be removed (see your -10).
2. Remove 18 screws (1), 36 lock washers (2), and 18 lock nuts (3) from window (4) and 2 window frames (5). Discard
lock washers and lock nuts.
3. Remove and separate window (4) and two window frames (5) from insulated cover (6).
INSTALLATION
1. Place window (4) and two window frames (5) in insulated cover (6).
2. Secure window (4) and 2 window frames (5) to insulated cover with 18 screws (1), 36 new lock washers (2), and 18 new
lock nuts (3).
3. Secure window curtain in closed position (see your -10).
END OF TASK
0468 00-1/2 blank

TM 9-2350-247-20-3
REPLACE CARGO DOOR INSULATION 0469 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Insulation tape WP 0542 00, Item 25 Engine stopped (see your -10)
REMOVAL
1. Scrape insulation (1) from cargo door (2).
2. Remove remaining insulation and adhesive with cleaning compound.
INSTALLATION
1. Trim new insulation to fit. Cut panels into sections about 3 feet square (1 m) in size.
2. Make sure surface to be covered is clean and dry. Spray or swab cleaning compound on back of insulation to activate
adhesive.
3. Allow 10 to 15 seconds for adhesive to become tacky. Butt sections together and press them firmly into place at once.
END OF TASK
0469 00-1/2 blank

TM 9-2350-247-20-3
REPLACE FLOOR PLATE COVERS 0470 00


INITIAL SETUP:

Unit See your -10

REMOVAL
1. Remove eight screws (1) and washers (2) from three plywood floor plate covers (3) in cargo compartment. Remove
covers from cargo compartment floor plates.
INSTALLATION
1. Place three plywood floor plate covers (3) on cargo compartment floor plates. Secure with eight washers (2) and
screws (1).
END OF TASK
0470 00-1/2 blank

TM 9-2350-247-20-3
REPLACE PERSONNEL SEAT COVERS 0471 00

INITIAL SETUP:

Unit See your -10
FM 10-16
Personnel Required Equipment Condition

Unit Mechanic Engine stopped (see your -10)
REMOVAL
1. Loosen straps (1) that secure bottom edges of two seat covers (2) to six tiedown eyes (3).
2. Remove two cover tubes (4) from between two seat covers (2) and cargo compartment personnel seats (5).
3. Loosen fastener tapes (6) that secure top edges of two seat covers (2) to hull.
4. Pass seat belts through holes (7) in two seat covers (2). Remove seat covers.
INSTALLATION
1. Place two seat covers (2) on cargo compartment personnel seats (5). Press fastener tapes (6) firmly to tapes on hull.
2. Pull seat belts through holes (7) in two seat covers (2).
3. Install two cover tubes (4) between two seat covers (2) and cargo compartment personnel seats (5).
4. Secure bottom edges of two seat covers (2) to six tiedown eyes (3) with six straps (1).
END OF TASK
0471 00-1/2 blank

TM 9-2350-247-20-3
REPLACE/REPAIR HEATER CONTROL BOX 0472 00

Removal (page 0472 00-1)

Disassembly (page 0472 00-2)
Assembly (page 0472 00-5)
Installation (page 0472 00-7)
INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
Electrical Tool Kit (WP 0541 00, Item 56) Equipment Condition
REMOVAL
1. Disconnect circuit 400 lead (1) from heater control box lead (2).
2. Disconnect heater wiring harness (3) from heater control box (4).
3. Remove two screws (5) and heater control box (4) from control box case (6).
4. Remove two screws (7), control box case (6), and two lock washers (8) from two hull weld nuts (9). Discard lock
washers.
0472 00-1
TM 9-2350-247-20-3
REPLACE/REPAIR HEATER CONTROL BOX — Continued 0472 00
DISASSEMBLY
NOTE
To repair circuit breaker, do Disassembly Step 1 and Assembly Step 5. To repair indicator light,
do Disassembly Step 2 and Assembly Step 4. To repair start switch, do Disassembly Step 3 and
Assembly Step 3. To repair HI-LO heater switch, do Disassembly Step 4 and Assembly Step 2.
To repair outlet receptacle, do Disassembly Step 5 and Assembly Step 1.
Tag electrical leads as they are removed.
1. Remove circuit breaker from heater control box as follows:
a. Remove two screws (1), lock washers (2), lead 16 (3), lead 17 (4), lead 17-3 (5), and jumper 15-17 (6) from circuit
breaker (7).
b. Remove two nuts (8), lock washers (9), indicator light negative lead (10), two screws (11), and circuit breaker (7)
from heater control box (12). Discard lock washers.
0472 00-2
TM 9-2350-247-20-3
NOTE
It may be necessary to loosen both screws when removing indicator light negative lead.
2. Remove indicator light from heater control box as follows:

a. Remove nut (8), lock washer (9), and indicator light negative lead (10) from circuit breaker (7).
b. Remove screw (1), lock washer (2), and lead 17-3 (5) from circuit breaker (7).
c. Remove screw (13), lock washer (14), and lead 19-2 (15) from start switch (16).
d. Unscrew cap (17) and remove bulb (18) from cable assembly (19).
e. Remove nut (20), lock washer (21), and cable assembly (19) from heater control box (12).
0472 00-3
TM 9-2350-247-20-3
3. Remove start switch from heater control box as follows:

a. Remove six screws (1), lock washers (2), jumper 15-17 (3), lead 13-19 (4), jumper 21-14 (5), jumper 21-18 (6),
lead 14 (7), lead 19-2 (8), lead 19 (9), and lead 20 (10) from start switch (11).
b. Remove nut (12), washer (13), and start switch (11) from heater control box (14).
4. Remove HI-LO heater switch from heater control box as follows:
a. Remove nut (15), lock washer (16), instruction plate (if applicable), and heater switch (17) from heater control box
(14). Discard lock washer.
b. Remove two screws (18), lock washers (19), lead 13-19 (4), and lead 12B (20) from heater switch (17).
5. Remove outlet receptacle from heater control box as follows:
a. Remove three screws (21), lock washers (22), lead 14 (7), lead 20 (10), and lead 19 (9) from start switch (11).
b. Remove screw (23), lock washer (24), and lead 17 (25) from circuit breaker (26).
c. Remove four screws (27), lock washers (28), and outlet receptacle (29) from heater control box (14). Discard lock
washers.
d. Remove screw (18), lock washer (19), and lead 12B (20) from heater switch (17).
0472 00-4
TM 9-2350-247-20-3
ASSEMBLY
NOTE
Before connecting electrical leads, check connection diagram (1) to make sure of proper
connection.
Make sure key in outlet receptacle is at the top.
1. Install outlet receptacle in heater control box as follows:
a. Install outlet receptacle (1) in heater control box (2). Secure with four new lock washers (3) and screws (4).
b. Install lead 17 (5) on circuit breaker (6) with lock washer (7) and screw (8).
c. Install lead 12B (9) on heater switch (10) with lock washer (11) and screw (12).
d. Install lead 19 (13), lead 20 (14), and lead 14 (15) on start switch (16) with three new lock washers (17) and
screws (18).
NOTE
Heater switch is marked ON and OFF.
2. Install HI-LO heater switch in heater control box as follows:
a. Place heater switch (10) with ON at the top of heater control box (2).
b. Install lead 13-19 (19) and lead 12B (9) on heater switch (10) with lock washer (11) and screw (12).
c. Install heater switch (10) in heater control box (2) with instruction plate (if applicable), new lock washer (20), and
nut (21).
0472 00-5
TM 9-2350-247-20-3
NOTE
Start switch has locked position and spring-loaded position.
3. Install start switch in heater control box as follows:
a. Place start switch (1) with locked position at top of heater control box (2).
b. Install start switch (1) in heater control box (2) with washer (3) and nut (4).
c. Install cable assembly (5) in heater control box (2) with lock washer (6) and nut (7).
d. Place lead 20 (8), lead 19 (9), lead 19-2 (10), lead 14 (11), jumper 21-18 (12), jumper 21-14 (13), lead 13-19 (14),
and jumper 15-17 (15) on start switch (1). Secure with six lock washers (16) and screws (17).
NOTE
Ensure that both circuit breaker screws are tight.
4. Install indicator light in heater control box as follows:
a. Install bulb (18) in cable assembly (5) with cap (19).
b. Install lead 19-2 (10) on start switch (1) with lock washer (16) and screw (17).
c. Install lead 17-3 (20) on circuit breaker (21) with lock washer (22) and screw (23).
d. Install indicator light negative lead (24) on circuit breaker (21) with lock washer (25) and nut (26).
5. Install circuit breaker in heater control box as follows:
a. Install circuit breaker (21) in heater control box (2) with four new lock washers (25), screws (27), indicator light
negative lead (24), and two nuts (26).
0472 00-6
TM 9-2350-247-20-3
b. Install jumper 15-17 (15), lead 17-3 (20), lead 17 (11), and lead 16 (10) on circuit breaker (21) with two lock
washers (22) and screws (23).
INSTALLATION
1. Place two new lock washers (1) and control box case (2) on two hull weld nuts (3). Secure with two screws (4).
2. Install heater control box (5) in control box case (2). Secure with two screws (6).
3. Connect heater wiring harness (7) to heater control box (5).
4. Connect circuit 400 lead (8) to heater control box lead (9).
0472 00-7
TM 9-2350-247-20-3
3. Check heater control box for proper operation.
4. Turn heater off (see your -10).
END OF TASK
0472 00-8
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER WIRING HARNESS 0473 00

INITIAL SETUP:

Unit See your -10
Multimeter (WP 0541 00, Item 29)
Wiping rag (WP 0542 00, Item 45) Carrier blocked (see your -10)
Grommet Battery negative lead(s) disconnected (WP 0292 00)
Lock washer (2) Top left access grille removed (see your -10 or
Lock washer (10) WP 0390 00)
Personnel Required Heater exhaust pipe removed (WP 0480 00 or
Unit Mechanic WP 0481 00)
REMOVAL
NOTE
Engine coolant heater wiring harness for M548A1 and M548A3 is removed and installed the
same way. M548A1 wiring harness is shown.
1. Pull back protector (1) on circuit 402A lead (2). Remove nut (3), washer (4), and lead from coolant pump (5).
2. Disconnect circuit 402A lead (6) from connector (7).
3. Remove nut (8), two lock washers (9), screw (10), and ground lead (11) from mount (12). Discard lock washers.
4. Disconnect connector (13) from coolant heater (14).
0473 00-1
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER WIRING HARNESS — Continued 0473 00
5. Disconnect connector (15) from control box (16) and circuit 400A lead (17) and slotted washer (18) from connector (19).
6. Remove 9 screws (20), 10 lock washers (21), 9 clamps (22), one grommet (23), coolant heater wiring harness (24), and
control box ground lead (25) from hull. Discard grommet and lock washers.
CLEANING
1. Clean coolant heater wiring harness with a clean wiping rag.
2. Check coolant heater wiring harness for continuity. Use multimeter.
3. Repair damaged coolant heater wiring harness (WP 0294 00). Replace coolant heater wiring harness that cannot be
repaired.
0473 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install new grommet (1) on coolant heater wiring harness (2). Install wiring harness and grommet in hull.
2. Secure control box ground lead (3) and coolant heater wiring harness (2) to hull with 9 clamps (4), 10 new lock washers
(5), and 9 screws (6).
3. Connect connector (7) to slotted washer (8) and circuit 400A lead (9) and connector (10) to control box (11).
4. Connect connector (12) to coolant heater (13).
5. Secure ground lead (14) to mount (15) with screw (16), nut (17), and two new lock washers (18).
6. Connect circuit 402A lead (19) to connector (20).
7. Secure circuit 402A lead (21) to coolant pump (22) with washer (23) and nut (24).
8. Place protector (25) over circuit 402A lead (21).
0473 00-3
TM 9-2350-247-20-3
2. Install heater exhaust pipe (WP 0480 00) or (WP 0481 00).
4. Start coolant heater (see your -10).
5. Check coolant heater wiring harness for proper operation.
6. Stop coolant heater (see your -10).
END OF TASK
0473 00-4
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER CONTROL BOX 0474 00

INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
REMOVAL
1. Disconnect wiring harness (1) from control box receptacle (2).
2. Disconnect circuit 400A lead (3) from connector (4).
3. Remove screw (5), two lock washers (6), and ground lead (7) from control box (8). Discard lock washers.
4. Remove two lock nuts (9), washers (10), four mounts (11), and control box (8) from hull. Discard lock nuts.
0474 00-1
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER CONTROL BOX — Continued 0474 00
INSTALLATION
1. Secure control box (8) to hull with four mounts (11), two washers (10), and new lock nuts (9).
2. Secure ground lead (7) to control box (8) with two new lock washers (6) and screw (5).
3. Connect circuit 400A lead (3) to connector (4).
4. Connect wiring harness (1) to receptacle (2).
3. Check coolant heater control box for proper operation.
END OF TASK
0474 00-2
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER FUEL PUMP/FUEL LINES 0475 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Lock nut (2) Power plant rear access door/panel removed
Lock washer (4) (see your -10)
Preformed packing
Top left access grille removed (see your -10 or
Personnel Required WP 0390 00)
REMOVAL
NOTE
M548A1 and M548A3 engine heater fuel pumps are removed and installed the same way.
For M548A1, do Step 5. For M548A3, do Step 6.
1. Disconnect circuit 402A lead (1) from fuel pump lead (2).
2. Disconnect tube (3) from elbow (4) and elbow (5).
3. Disconnect tube (6) from elbow (7) and union (8).
0475 00-1
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER FUEL PUMP/FUEL LINES — Continued 0475 00
4. Remove elbow (5) from coolant heater (9).

5. Remove elbow (4), elbow (7), and nipple (10) from fuel pump (11).
6. Remove elbow (4) and elbow (7) from fuel pump (11).
7. Remove union (8) and preformed packing (12) from manifold block (13). Discard preformed packing.
8. Remove two lock nuts (14), four lock washers (15), two washers (16), screws (17), ground lead (18), ground lead (19),
capacitor (20), and fuel pump (11) from bracket (21). Discard lock washers and lock nuts.
0475 00-2
TM 9-2350-247-20-3
INSTALLATION
NOTE
For M548A1, do Step 3.
1. Place capacitor (1), ground lead (2), ground lead (3), and fuel pump (4) on bracket (5). Secure with two screws (6),
washers (7), four new lock washers (8), and two new lock nuts (9).
2. Install new preformed packing (10) and union (11) in manifold block (12).
NOTE
On M548A3 make sure elbow (14) points down and elbow (15) points up.
3. Install nipple (13), elbow (14), and elbow (15) in fuel pump (4).
4. Install elbow (14) and elbow (15) in fuel pump (4).
5. Install elbow (16) in coolant heater (17).
6. Connect tube (18) to union (11) and elbow (14).
7. Connect tube (19) to elbow (16) and elbow (15).
8. Connect fuel pump lead (20) to circuit 402A lead (21).
0475 00-3
TM 9-2350-247-20-3
3. Check for leaks and proper operation of coolant heater.
5. Install top left access grille or (see your -10 or (WP 0390 00)).
6. Install power plant rear access door/panel (see your -10).
END OF TASK
0475 00-4
TM 9-2350-247-20-3
REPLACE BATTERY BOX HEAT EXCHANGER/HOSES/FITTINGS 0476 00

INITIAL SETUP:

Unit See your -10
Materials/Parts
Coolant Carrier blocked (see your -10)
Lock nut (3) Batteries removed (WP 0290 00 or WP 0293 00)
Personnel Required Top left access grille removed (see your -10 or
REMOVAL
1. Turn coolant valve (1) and coolant valve (2) off.
NOTE
Cap or cover lines to prevent fluid leaks.
2. Remove two lock nuts (3), screws (4), and three clamps (5) that secure hose (6) to engine oil filler tube and battery box.
Discard lock nuts.
3. Disconnect hose (6) from nipple (7). Remove nipple from coolant valve (1).
4. Disconnect hose (6) from nipple (8). Remove nipple from coolant heater (9).
5. Disconnect hose (10) from elbow (11). Remove elbow from coolant heater (9).
6. Remove clamp (12) and hose (10) from heat exchanger (13).
7. Remove two clamps (14) and hose (15) from heat exchanger (13) and valve (16). Remove heat exchanger from battery
box.
0476 00-1
TM 9-2350-247-20-3
REPLACE BATTERY BOX HEAT EXCHANGER/HOSES/FITTINGS — Continued 0476 00
8. Remove valve (1) from coolant pump (2).
9. Disconnect hose (3) from nipple (4). Remove nipple from coolant valve (5).
10. Remove clamp (6) from hose (3). Disconnect hose from adapter (7).
11. Remove adapter (7) from coolant pump (2).
12. Remove lock nut (8), screw (9), and clamp (10) from clamp (11). Discard lock nut.
INSTALLATION
NOTE
If coolant valve (12), coolant valve (5), nipple (13), elbow (14), nipple (15), and elbow (16) are
removed, drain carrier cooling system (WP 0213 00) or (WP 0214 00).
NOTE
Apply a light coat of sealing compound to outer tapered thread fittings before installation.
1. If removed, install nipple (15) in oil cooler housing.
2. If removed, install elbow (16) on nipple (15).

3. If removed, install coolant valve (5) on elbow (16).
4. Install nipple (4) in coolant valve (5).
5. Install adapter (7) in coolant pump (2).
6. Secure hose (3) and clamp (10) to clamp (11) with screw (9) and new lock nut (8).
7. Connect hose (3) to nipple (4).
0476 00-2
TM 9-2350-247-20-3
8. Secure hose (3) to adapter (7) with clamp (6).
9. If removed, install elbow (1) in engine block.

10. If removed, install nipple (2) in elbow (1).
11. If removed, install coolant valve (3) on nipple (2).
12. Install nipple (4) in coolant valve (3).
13. Install nipple (5) in coolant heater (6).
14. Connect hose (7) to nipple (5) and nipple (4).
15. Install valve (8) in coolant pump (9).
0476 00-3
TM 9-2350-247-20-3
16. Install heater exchanger (10) in battery box.

17. Connect hose (11) to valve (8) and heat exchanger (10). Secure hose with two clamps (12).
18. Install elbow (13) in coolant heater (6).
19. Connect hose (14) to elbow (13) and to heat exchanger (10). Secure hose to heat exchanger with clamp (15).
20. Secure hose (7) to battery box and engine oil filler tube with three clamps (16), two screws (17), and new lock nuts (18).
21. Turn coolant valve (19) and coolant valve (3) on.
1. Install batteries (WP 0290 00) or (WP 0293 00).
2. If drained, fill carrier cooling system (WP 0212 00) or (WP 0214 00).
4. Check coolant heater for proper operation.
END OF TASK
0476 00-4
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER 0477 00

INITIAL SETUP:

Unit See your -10
Equipment Condition
Materials/Parts
Lock washer Battery negative lead(s) disconnected (WP 0292 00)
REMOVAL
NOTE
Removal procedures for M548A1 and M548A3 engine coolant heater are similar. M548A3
coolant heater does not have a cover. M548A1 coolant heater is shown.
1. Turn off coolant valve (1) and coolant valve (2).
2. Remove two screws (3) and washers (4) that secure heater cover plate (5) to mounting bracket (6). Remove plate.
3. Disconnect engine inlet and plate outlet coolant hoses from engine coolant heater (WP 0476 00).
0477 00-1
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER — Continued 0477 00
4. Disconnect pump-to-heater fuel tube (7) from heater nipple (8).

5. Loosen clamp (9) that secures lower exhaust pipe (10) to engine coolant heater (11). Disconnect pipe from heater.
6. Remove engine coolant heater ground lead nut (12) and lock washer (13). Disconnect heater ground lead (14) from end
cover on heater. Discard lock washer.
7. Disconnect wiring harness (15) from receptacle (16) on engine coolant heater (11).
8. Loosen two mounting clamps (17) that secure engine coolant heater (11) to mounting bracket (6). Remove engine
coolant heater.
9. If engine coolant heater (11) is to be replaced, remove heater nipple (8) from engine coolant heater.
0477 00-2
TM 9-2350-247-20-3
INSTALLATION
NOTE
Installation procedures for M548A1 and M548A3 engine coolant heater are similar. M548A3
coolant heater does not have a cover. M548A1 coolant heater is shown.
NOTE
1. Place engine coolant heater (1) on bracket (2). Secure with two clamps (3).
2. Connect wiring harness (4) to receptacle (5) on engine coolant heater (1).
3. Connect ground lead (6) to engine coolant heater (1). Secure with new lock washer (7) and nut (8).
4. Connect exhaust pipe (9) to engine coolant heater (1). Secure with clamp (10).
5. If replacement engine coolant heater (1) is being installed, install heater nipple (11) in heater.
6. Connect pump-to-heater fuel tube (12) to heater nipple (11).
7. Connect inlet and outlet hoses to engine coolant heater (WP 0476 00).
8. Place cover plate (13) on bracket (2). Secure with two washers (14) and screws (15).
9. Open coolant valve (16) and coolant valve (17).
0477 00-3
TM 9-2350-247-20-3
2. Start engine coolant heater (see your -10).
3. Check engine coolant heater for proper operation.
4. Stop engine coolant heater (see your -10).
END OF TASK
0477 00-4
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER COOLANT PUMP 0478 00

INITIAL SETUP:

Unit See your -10
Equipment Condition
Materials/Parts
Lock washer Battery negative lead(s) disconnected (WP 0292 00)
REMOVAL
NOTE
M548A1 and M548A3 coolant pumps are removed and installed the same way. M548A1 coolant
pump is shown.
1. Turn off coolant valve (1) and coolant valve (2).
2. Remove nut (3), washer (4), and circuit 402A lead (5) from coolant pump (6).
3. Loosen two clamps (7). Remove hose (8) and hose (9) from coolant pump (6).
4. Remove nut (10), lock washer (11), and ground lead (12) from coolant pump (6). Discard lock washer.
5. Remove two screws (13), clamp (14), and coolant pump (6) from mount (15).
0478 00-1
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER COOLANT PUMP — Continued 0478 00
INSTALLATION
1. Place coolant pump (1) on mount (2). Secure with clamp (3) and two screws (4).
2. Secure ground lead (5) to coolant pump (1) with new lock washer (6) and nut (7).
3. Install hose (8) and hose (9) on coolant pump (1). Secure with two clamps (10).
4. Secure circuit 402A lead (11) to coolant pump (1) with washer (12) and nut (13).
5. Open coolant valve (14) and coolant valve (15).
1. Turn heater fuel pump to OFF (see your -10).
3. Move run-off-start switch to START (see your -10). Run coolant heater pump for a maximum of 30 seconds, then shut
it off.
4. Turn coolant heater fuel pump ON (see your -10).
6. Check coolant heater for proper operation and leaks.
8. Turn coolant heater fuel pump OFF (see your -10).
END OF TASK
0478 00-2
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT/VEHICLE COMPARTMENT HEATER 0479 00

EXHAUST PIPES GUARD (M548A1)
INITIAL SETUP:

Unit Unit Mechanic

Open End Wrench Set (WP 0541 00, Item 60)
0479 00-1
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT/VEHICLE COMPARTMENT HEATER EXHAUST PIPES 0479 00

GUARD (M548A1) — Continued
REMOVAL
1. Remove left side intake grille (WP 0390 00).
2. Loosen three nuts (1) and remove exhaust hood (2) from heater exhaust pipes (3).
3. Remove eight lock nuts (4), washers (5), and screws (6) from guard (7), two mounting brackets (8), and two mounting
brackets (9). Remove guard from four mounting brackets. Discard lock nuts.
4. Remove three lock nuts (10) and screws (11) from two upper double angle brackets (12). Remove two upper double
angle brackets with two mounting brackets (8) from heater exhaust pipes (3). Discard lock nuts.
5. Remove three lock nuts (10) and screws (11) from two lower double angle brackets (13). Remove two lower double
angle brackets with two mounting brackets (9) from heater exhaust pipes (3). Discard lock nuts.
6. Remove eight screws (14) and washers (15) from two mounting brackets (8), two mounting brackets (9), upper double
angle brackets (12), and lower double angle brackets (13).
0479 00-2
TM 9-2350-247-20-3

INSTALLATION
1. Install two mounting brackets (1) and two mounting brackets (2) on upper double angle brackets (3) and lower double
angle brackets (4) with eight screws (5) and washers (6).
0479 00-3
TM 9-2350-247-20-3

NOTE
When installing double angle brackets and mounting brackets on heater exhaust pipes, make
sure mounting brackets on upper part of exhaust pipes are facing up, and mounting brackets on
lower part of exhaust pipes are facing down.
2. Install two upper double angle brackets (3) and mounting brackets (1) on heater exhaust pipes (7) so bottom of each
mounting bracket is 3 3/4-4 inches (9.5-10.1 cm) from top of exhaust pipes with three screws (8) and new lock nuts (9).
Finger tighten nuts only.
0479 00-4
TM 9-2350-247-20-3

3. Install two lower double angle brackets (4) and mounting brackets (2) on heater exhaust pipes (7) 22 7/16-22 9/16 inches
(57-57.3 cm) from upper double angle brackets (2) with three screws (8) and new lock nuts (9). Measure from centerline
to centerline.
0479 00-5
TM 9-2350-247-20-3

4. Tighten lock nuts (9) on upper double angle brackets (3) and lower double angle brackets (4).
5. Place guard (10) over heater exhaust pipes (7) with holes on guard aligned with holes on mounting bracket (1) and
mounting bracket (2).
6. Install guard (10) on mounting bracket (1) and mounting bracket (2) with eight screws (11), washers (12), and new lock
nuts (13).
7. Install exhaust hood (14) on heater exhaust pipes (7) and tighten two nuts (15).
8. Install left side intake grille (WP 0390 00).
END OF TASK
0479 00-6
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER EXHAUST SYSTEM (M548A1) 0480 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Lock nut Battery negative lead disconnected (WP 0292 00).
Lock washer (3) Engine coolant heater exhaust guard removed
Unit Mechanic Top left access grille removed (WP 0390 00)
0480 00-1
TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER EXHAUST SYSTEM (M548A1) — Continued 0480 00
REMOVAL
1. Remove three nuts (1), lock washers (2), screws (3), and hood (4) from exhaust pipe (5) and exhaust pipe (6). Discard
lock washers.
2. Remove three screws (7), six washers (8), lock nut (9), and two clamps (10) that secure exhaust pipe (5) and exhaust pipe
(6) to two weld nuts (11). Discard lock nut.
3. Remove clamp (12) and exhaust pipe (5) from exhaust pipe (13).
4. Remove clamp (14) and exhaust pipe (13) from coolant heater (15).
5. Remove clamp (16) and moisture trap (17) from exhaust pipe (13).
0480 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install moisture trap (1) in exhaust pipe (2). Secure with clamp (3).
2. Place exhaust pipe (2) on coolant heater (4). Secure with clamp (5).
3. Install exhaust pipe (6) over exhaust pipe (2). Secure with clamp (7).
4. Secure exhaust pipe (2), exhaust pipe (8), and exhaust pipe (6) to two weld nuts (9) with two clamps (10), new lock nut
(11), six washers (12), and three screws (13).
5. Place hood (14) on exhaust pipe (8) and exhaust pipe (6). Secure with three screws (15), new lock washers (16), and
nuts (17).
3. Install engine coolant heater exhaust guard (WP 0479 00).
END OF TASK
0480 00-3/4 blank

TM 9-2350-247-20-3
REPLACE ENGINE COOLANT HEATER EXHAUST SYSTEM (M548A3) 0481 00

INITIAL SETUP:

Unit See your -10
Equipment Condition
General Mechanic’s Tool Kit (WP 0541 00, Item 57) Carrier blocked (see your -10)
Personnel Required MASTER SWITCH OFF (see your -10)
Unit Mechanic Both battery negative leads disconnected (WP 0292 00)
Top left access grille removed (see your -10)
0481 00-1
TM 9-2350-247-20-3
REMOVAL
1. Loosen clamp (1) and clamp (2) and remove exhaust pipe (3) with adapter (4) from coolant heater (5) and exhaust
housing.
2. Loosen clamp (6) and remove adapter (4) from exhaust pipe (3).
3. Loosen clamp (7) and remove cap (8) from exhaust housing.
INSTALLATION
1. Install cap (8) and clamp (7) on exhaust housing. Tighten clamp.
2. Install adapter (4) and clamp (6) on exhaust pipe (3). Tighten clamp.
3. Align adapter with exhaust housing and exhaust pipe with coolant heater (5). Tighten clamp (1) and clamp (2).
1. Install top left access grille (see your -10).
END OF TASK
0481 00-2
TM 9-2350-247-20-3
REMOVE/INSTALL MATERIAL HANDLING KIT 0482 00


INITIAL SETUP:

Unit See your -10

REMOVAL
1. Remove rifle racks (WP 0488 00).
2. Remove bulkhead protector (WP 0487 00).
3. Remove personnel seats and safety belts (WP 0486 00).
4. Remove hoist and stops (WP 0484 00).
5. Remove beam, beam supports, and stops (WP 0483 00).
INSTALLATION
NOTE
If cargo cover is not installed, install two bolt-on bows on hull (WP 0417 00).
1. Install beam, beam supports, and stops (WP 0483 00).
2. Install hoist and stops (WP 0484 00).
3. Install personnel seats and safety belts (WP 0486 00).
4. Install bulkhead protector (WP 0487 00).
5. Install rifle racks (WP 0488 00).
END OF TASK
0482 00-1/2 blank

TM 9-2350-247-20-3
REPLACE BEAM/BEAM SUPPORTS/STOPS 0483 00

INITIAL SETUP:

Unit Unit Mechanic
Helper (H)


Hoist removed (WP 0484 00)
REMOVAL
NOTE
There are two beam supports. They are each removed and installed the same way.
1. Remove screw (1), lock nut (2), and two center stops (3) from beam (4). Discard lock nut.
NOTE
Beams are heavy and awkward. Use helper to remove and install beams.
2. Loosen beam lock (5) on each beam support (6). Slide beam (4) out of supports.
3. Turn retaining pin handle (7) of retaining pin (8) up and pull pin from beam support (6). Remove support from bolt-on
bow support (9).
0483 00-1
TM 9-2350-247-20-3
REPLACE BEAM/BEAM SUPPORTS/STOPS — Continued 0483 00
DISASSEMBLY
1. Unscrew and remove beam lock (5), spring (10), and bolt lock (11) from beam support (6).
2. Remove screw (12), two S-hooks (13), and chain (14) from beam support (6). Remove S-hook from retaining pin
handle (7).
3. Remove two screws (15), lock washers (16), and one pin retainer (17) from beam support (6). Discard lock washers.
ASSEMBLY
1. Install spring (1), bolt lock (2), and beam lock (3) on beam support (4).
2. Place pin retainer (5) on beam support (4). Secure with two new lock washers (6) and screws (7).
3. Attach two S-hooks (8) to chain (9). Secure S-hook at one end to beam support (4) with screw (10).
4. Install other S-hook (8) on handle (11) of retaining pin (12).
0483 00-2
TM 9-2350-247-20-3
REPLACE BEAM/BEAM SUPPORTS/STOPS — Continued 0483 00
INSTALLATION
NOTE
Bend or close S-hooks so they will not interfere with pin removal and installation.
1. Place beam support (4) on bolt-on bow support (13). Secure with retaining pin (12).
NOTE
Beams can be placed in several positions. If beam is to be angled, one beam support must be at
center of bolt-on bow support (see your -10).
2. Install beam (14) on two beam supports (4). Tighten beam locks (3).
CAUTION
When you install beam, make sure center stops are in front of rear beam support and beam
locks are toward front.
NOTE
To prepare hoist and beam for travel, see your -10.
3. Install two center stops (15) at each beam support (4) with screw (16) and new lock nut (17).
1. Install hoist (WP 0484 00).
END OF TASK
0483 00-3/4 blank

TM 9-2350-247-20-3
REPLACE HOIST/STOPS/SLING 0484 00

INITIAL SETUP:

Unit Unit Mechanic
Helper (H)
References
Materials/Parts TB 43-0142
Cotter pin
Equipment Condition
Lock nut (2)
Cotter pin Engine stopped (see your -10)
REMOVAL
1. Remove sling (1) from hoist chain hook (2). Remove strap (3) and release chain (4) from bow support (5).
2. Remove two screws (6), lock nuts (7), washers (8), and four beam end stops (9) from beam (10). Discard lock nuts.
3. Loosen trolley lock handle (11).
0484 00-1
TM 9-2350-247-20-3
REPLACE HOIST/STOPS/SLING — Continued 0484 00
WARNING
Hoist weighs 77 lb (35 kg). You could be seriously injured when removing hoist. Removal of
hoist requires two people.
4. Remove hoist (12) from beam (10). Have helper assist.
DISASSEMBLY
1. Remove cotter pin (13), slotted nut (14), two washers (15), and trolley lock (16) from bolt (17) on hoist (12). Discard
cotter pin.
2. Remove cotter pin (18), slotted nut (19), two washers (20), trolley lock handle (11), and nut (21) from trolley lock (16).
Discard cotter pin.
0484 00-2
TM 9-2350-247-20-3
REPLACE HOIST/STOPS/SLING — Continued 0484 00
ASSEMBLY
1. Install trolley lock handle (1) and nut (2) in trolley lock (3) with two washers (4) and one slotted nut (5). Secure slotted
nut with new cotter pin (6).
2. Install assembled trolley lock (3) on bolt (7) with two washers (8) and one slotted nut (9). Secure slotted nut with new
cotter pin (10).
INSTALLATION
WARNING
Hoist weighs 77 lb (35 kg). You could be seriously injured when installing hoist. Installation of
hoist requires two people.
1. Install hoist (11) on beam (12). Tighten trolley lock handle (1). Have helper assist.
2. Install four beam end stops (13) with two screws (14), washers (15), and new lock nuts (16).
3. Secure chain (17) to bow support (18) with strap (19).
4. Attach sling (20) to chain hook (21).
END OF TASK
0484 00-3/4 blank

TM 9-2350-247-20-3
REPAIR HOIST ASSEMBLY 0485 00

INITIAL SETUP:

Unit
Unit Mechanic
Retaining Pliers Set (WP 0541 00, Item 32) References
Drive Pin Punch (WP 0541 00, Item 38) TB 43-0142
Materials/Parts
Cotter pin (5)
Cotter pin Equipment Condition
Lock washer (3)
Lock washer (3)
Lock washer Hoist removed from carrier (WP 0484 00)
0485 00-1
TM 9-2350-247-20-3
REPAIR HOIST ASSEMBLY — Continued 0485 00
REMOVAL
1. Remove right side cotter pin (1), right side cotter pin (2), nut (3), nut (4), washer (5), and washer (6) from right side plate
(7), two right side track wheels (8), and hoist assembly (9). Discard cotter pins.
2. Remove left side cotter pin (10), left side cotter pin (11), nut (12), nut (13), washer (14), and washer (15) from left side
plate (16), two left side track wheels (17), and hoist assembly (9). Discard cotter pins.
3. Remove lock clamp suspension pin (18) from left side plate (7) and right side plate (16).
4. Remove left side plate (7), right side plate (16), two left side track wheels (17), and right side track wheels (8) from hoist
assembly (9).
5. Remove two nuts (19) and two right side track wheels (8) from right side plate (7).
6. Remove two nuts (20) and two left side track wheels (17) from left side plate (16).
7. Remove lock clamp suspension pin (21) and hoist assembly spacer (22) from hoist assembly (9).
0485 00-2
TM 9-2350-247-20-3
8. Remove three screws (1), lock washers (2), and hand chain guide cover (3) from suspension frame (4). Discard lock
washers.
9. Remove hand chain (5) from chain handwheel (6).
10. Remove cotter pin (7), nut (8), and washer (9) from chain handwheel (6) and driving pinion (10). Turn chain handwheel
to the left to release from driving pinion. Remove chain handwheel. Discard cotter pin.
0485 00-3
TM 9-2350-247-20-3
11. Remove friction disk (11) and spring washer (12) from chain handwheel (6) and separate ratchet disk (13) and brake disk
(14) from friction plate (15).
12. Turn friction plate (15) to the left and remove from driving pinion (10).
13. Remove three retaining rings (16), ring pawl (17), and three ring pawl springs (18) from suspension frame (4).
0485 00-4
TM 9-2350-247-20-3
14. Remove three screws (1), lock washers (2), and gear cover (3) from suspension frame (4). Discard lock washers.
15. Remove load gear retaining ring (5) and load sheave (6) from load gear (7) Use retaining pliers set.
16. Remove cotter pin (8), washer (9), and chain end pin (10) from suspension frame (4). Discard cotter pin.
17. Remove two screws (11), lock washers (12), and load chain guide (13) from suspension frame (4). Discard lock washers.
18. Remove screw (14), lock washer (15), load chain stripper (16), and load chain and hook assembly (17) from suspension
frame (4). Discard lock washer.
0485 00-5
TM 9-2350-247-20-3
19. Remove bearing retaining ring (18), load sheave (6), and load sheave bearing (19) from suspension frame (4). Use
retaining pliers set
20. Remove driving pinion (20) with driving pinion bearing (21) from suspension frame (4). Remove outer bearing retaining
ring (22), inner bearing retaining ring (23), and driving pinion bearing (21) from driving pinion (20). Use retaining pliers
set.
21. Pull driving pinion bearing (24) and load sheave bearing (25) from suspension frame (4).
22. Remove retaining ring (26) from nut end of load hook (27).
23. Press anchor pin (28) from load hook (27) and separate load chain (29) from load hook.
0485 00-6
TM 9-2350-247-20-3
INSTALLATION
1. Install load hook (27) with anchor pin (28) on load chain (29).
2. Install retaining ring (26) on nut end of load hook (27).
0485 00-7
TM 9-2350-247-20-3
3. Install load sheave bearing (1) and driving pinion bearing (2) (with bearing lips facing out) into suspension frame (3).
Press into place.
4. Install inner bearing retaining ring (4) in groove on driving pinion (5). Press driving pinion bearing (6) on splined end of
driving pinion with bearing lip facing toward splines. Install outer bearing retaining ring (7) in groove of driving pinion.
Use retaining pliers set.
5. Install driving pinion (5) with driving pinion bearing (6) into bore of suspension frame (3). Press driving pinion into
driving pinion bearing (2) and driving pinion bearing (6) into bore of suspension frame. Use drive pin punch.
0485 00-8
TM 9-2350-247-20-3
6. Align load sheave bearing (8) on splined end of load sheave (9) with bore of suspension frame (3). Press load sheave (9)
with load sheave bearing into bore of suspension frame (3) and load sheave bearing (1) into bore of suspension frame.
Use drive pin punch. Install retaining ring (10) into groove of suspension frame. Use retaining pliers set.
7. Install load chain and hook assembly (11), load chain stripper (12) with screw (13), and new lock washer (14) on
suspension frame (4).
8. Install load chain guide (15) with two screws (16) and new lock washers (17) on suspension frame (4).
9. Install chain link of load chain and hook assembly (11) on suspension frame (4) with chain end pin (18), washer (19),
and new cotter pin (20).
10. Install load gear (21) on load sheave (9) with retaining ring (22).
11. Install gear cover (23), three screws (24) and new lock washers (25) on suspension frame (4).
0485 00-9
TM 9-2350-247-20-3
12. Install three ring pawl springs (1), ring pawl (2), and three spring retaining rings (3) on suspension frame (4). Use
retaining pliers set.
13. Install friction plate (5) on driving pinion (6) and turn to the right to secure.
14. Install brake disk (7) and ratchet disk (8) on friction disk (5) with spring washer (9) and friction disk (10) on chain
handwheel (11).
0485 00-10
TM 9-2350-247-20-3
15. Install chain handwheel (11), spring washer (9), and friction disk (10) on driving pinion (6). Turn chain handwheel to the
right on driving pinion and install washer (12), nut (13) and new cotter pin (14).
16. Install hand chain (15) over chain handwheel (11).
17. Install chain guide cover (16), three new lock washers (17), and screws (18) on suspension frame (4).
0485 00-11
TM 9-2350-247-20-3
18. Install hoist assembly spacer (1) on hoist assembly (2) with lock clamp suspension pin (3) through hoist assembly and
hoist assembly spacer.
19. Install two left side track wheels (4) with two nuts (5) on left side plate (6).
20. Install two right side track wheels (7) with two nuts (8) on right side plate (9).
0485 00-12
TM 9-2350-247-20-3
21. Install left side plate (6) with two left side track wheels (4) and right side plate (9) with two right side track wheels (7) on
hoist assembly (2) with washer (10), washer (11), nut (12), nut (13), new cotter pin (14), and new cotter pin (15).
22. Install lock clamp suspension pin (16) in left side plate (6) and right side plate (9) with washer (17), washer (18), nut
(19), nut (20), new cotter pin (21), and new cotter pin (22).
0485 00-13
TM 9-2350-247-20-3
ADJUSTMENT
1. Add or remove flat washers, similar to flat washer (1) between left side plate (2), right side plate (3), and suspension
frame (4) to maintain approximately 7/8 inch (22 mm) dimension between inner surfaces of left side track wheel (5) and
right side track wheel (6). Left and right side plates must be equally spaced from centerline of hoist assembly.
2. Add or remove flat washer (1), flat washer (7), flat washer (8), and flat washer (9) as necessary to align cotter pin hole in
lock clamp suspension pin (10) and lock clamp suspension pin (11) with slots in nut (12), nut (13), nut (14), and nut (15)
to provide proper lock for nuts.
1. Install hoist on carrier (WP 0484 00).
END OF TASK
0485 00-14
TM 9-2350-247-20-3
REPLACE PERSONNEL SEATS/SAFETY BELT 0486 00

INITIAL SETUP:

Unit
See your -10
Materials/Parts
Equipment Condition
Lock nut (2)
REMOVAL
NOTE
All cargo compartment seats and safety belts are removed and installed the same way.
If secondary cargo area heater kit is used, remove seat covers and tubes (WP 0471 00).
1. Unhook two backrest straps (1) from two loops (2) on backrest cushion (3). Remove straps from hull retainers (4).
2. Slide seat cushion (5) and retainers (6) forward to remove retainers from slots (7) in sponson (8). Remove retainers from
cushion.
3. Remove two washers (9), lock nuts (10), screws (11) and both halves of safety belt (12) from retainers (13). Discard lock
nuts.
0486 00-1
TM 9-2350-247-20-3
REPLACE PERSONNEL SEATS/SAFETY BELT — Continued 0486 00
INSTALLATION
NOTE
If secondary cargo heater kit is installed, install seat covers and tubes (WP 0471 00).
1. Install each safety belt half (12) to each retainer (13) with two screws (11), washers (9), and new lock nuts (10).
2. Install seat cushion retainers (6) on seat cushion (5). Place cushion (5) and retainers on sponson (8). Hook retainers in
slots (7).
3. Install two backrest straps (1) on hull retainers (4) and through two loops (2) on backrest cushion (3). Buckle straps.
END OF TASK
0486 00-2
TM 9-2350-247-20-3
REMOVE/INSTALL BULKHEAD PROTECTOR 0487 00

INITIAL SETUP:

Unit See your -10
REMOVAL
1. Remove three screws (1), washers (2), and bulkhead protector (3) from bulkhead (4).
INSTALLATION
1. Install bulkhead protector (3) on bulkhead (4) with three screws (1) and washers (2).
END OF TASK
0487 00-1/2 blank

TM 9-2350-247-20-3
REPLACE RIFLE RACK 0488 00


INITIAL SETUP:

Unit See your -10

REMOVAL
1. Unhook three latches (1). Lift racks (2) up to remove mounting pins (3) from cargo door (4).
0488 00-1
TM 9-2350-247-20-3
REPLACE RIFLE RACK — Continued 0488 00
INSTALLATION
1. Place three racks (2) on inside cargo door (4). Make sure mounting pins (3) are in holes on top of door.
2. Engage three latches (1).
END OF TASK
0488 00-2
TM 9-2350-247-20-3
REPLACE AIR BRAKE COMPRESSOR (M548A1) 0489 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Container, 1 gallon Power plant rear access door removed (see your -10)
Gasket Top access cover and grilles removed (WP 0390 00)
Gasket (2) Bulkhead protector removed, if material handling kit is
Lock washer (2) installed (WP 0487 00)
Lock nut (4)
Compressor drive pulley and belts removed
Unit Mechanic Air strainer removed (WP 0500 00)
0489 00-1
TM 9-2350-247-20-3
REPLACE AIR BRAKE COMPRESSOR (M548A1) — Continued 0489 00
REMOVAL
1. Open drain cock (1) to release reservoir pressure.
2. Disconnect compressor-to-oil filler tube hose (2) from oil filler tube union (3). Place open end in 1 gallon container.
Drain oil from compressor (4).
3. Disconnect governor-to-compressor air hose (5) from compressor nipple (6). Remove nipple from compressor (4).
0489 00-2
TM 9-2350-247-20-3
4. Disconnect compressor discharge hose (1) from discharge elbow (2).

5. Remove discharge elbow (2) from adapter (3).
6. Disconnect and cap engine-to-compressor hose (4) from elbow (5). Remove elbow from compressor (6).
7. Remove four screws (7), washers (8), lock nuts (9), spacer (10), two gaskets (11), and compressor (6) from platform
(12). Discard lock nuts and gaskets.
8. Remove two screws (13), lock washers (14), adapter (3), and gasket (15) from compressor (6). Discard lock washers and
gasket.
0489 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Install new gasket (15) and adapter (3) on compressor (6) with two new lock washers (14) and screws (13).
2. Install two new gaskets (11), spacer (10), and compressor (6) on platform (12) with four new lock nuts (9), washers (8),
and screws (7).
3. Install engine-to-compressor hose elbow (5) in compressor (6). Connect engine-to-compressor hose (4) to elbow.
4. Install discharge elbow (2) in adapter (3).
5. Connect compressor discharge hose (1) to discharge elbow (2).
0489 00-4
TM 9-2350-247-20-3
6. Install compressor nipple (1) in compressor (2). Connect governor-to-compressor air hose (3) to nipple.
7. Install oil filler union (4) in engine. Connect compressor-to-oil filler tube hose (5) to union.
1. Fill compressor (2) with oil.
2. Close drain cock (6).
4. Check for proper operation of air brake compressor.
6. Install air strainer (WP 0500 00).
7. Install compressor drive pulley and belts (WP 0499 00).
9. Install top access cover and grilles (WP 0390 00).
END OF TASK
0489 00-5/6 blank

TM 9-2350-247-20-3
REPLACE AIR BRAKE GOVERNOR (M548A1) 0490 00

INITIAL SETUP:

Unit See your -10
Antiseize compound (WP 0542 00, Item 6) Carrier blocked (see your -10)
Lock nuts (2) Top access cover and grilles removed (WP 0390 00)
Personnel Required Power plant rear access cover/door removed
Unit Mechanic (see your -10)
REMOVAL
1. Release air reservoir pressure at drain cock (1).
2. Disconnect compressor-to-governor air hose (2) from adapter (3).
3. Disconnect reservoir air tube (4) from adapter (5).
4. Remove two lock nuts (6), screws (7), and governor (8) from air cleaner assembly. Discard lock nuts.
5. Remove adapter (3) and adapter (5) from governor (8).
0490 00-1
TM 9-2350-247-20-3
REPLACE AIR BRAKE GOVERNOR (M548A1) — Continued 0490 00
INSTALLATION
1. Install governor (1) on air cleaner assembly with two new lock nuts (2) and screws (3).
2. Apply antiseize compound sparingly to threads of adapter (4) and adapter (5).
3. Install adapter (4) and adapter (5)0 on governor (1).
4. Connect compressor-to-governor air hose (6) to adapter (4).
5. Connect reservoir air tube (7) to adapter (5).
2. Check operation of governor.
5. Install power plant rear access cover/door (see your -10).
END OF TASK
0490 00-2
TM 9-2350-247-20-3
REPLACE AIR BRAKE RESERVOIR (M548A1) 0491 00


INITIAL SETUP:

Unit See your -10

Unit Mechanic Top access cover and grilles removed (WP 0390 00)
Helper (H) Center seat raised (see your -10)
REMOVAL
1. Release air pressure from reservoir (1) at drain cock (2).
2. Disconnect air tube line (3), air tube line (4), and air tube line (5) from reservoir (1).
3. Remove air tube fittings (WP 0495 00).
4. Remove air brake safety valve (WP 0492 00).
5. Remove drain cock (2) from reservoir (1).
NOTE
Use helper to lift out reservoir. It is awkward to lift out.
6. Remove two nuts (6), clamp (7), clamp (8), and reservoir (1) from two brackets (9). Lift out reservoir.
0491 00-1
TM 9-2350-247-20-3
REPLACE AIR BRAKE RESERVOIR (M548A1) — Continued 0491 00
INSTALLATION
1. Install reservoir (1) on two brackets (9) with clamp (7), clamp (8), and nuts (6).
2. Install drain cock (2) on reservoir (1).
3. Install air safety valve (WP 0492 00).
4. Install air tube fittings (WP 0495 00).
5. Connect air tube line (3), air tube line (4), and air tube line (5) to reservoir (1).
END OF TASK
0491 00-2
TM 9-2350-247-20-3
REPLACE AIR BRAKE SAFETY VALVE (M548A1) 0492 00


INITIAL SETUP:

Unit See your -10

REMOVAL
1. Turn safety valve (1) to the left and remove from fitting (2) at end of reservoir (3).
INSTALLATION
1. Install safety valve (1) in fitting (2) at end of reservoir (3) and turn valve to the right.
END OF TASK
0492 00-1/2 blank

TM 9-2350-247-20-3
REPLACE STOPLIGHT SWITCH (M548A1) 0493 00

INITIAL SETUP:

Unit See your -10

Lock nut (2) Top access cover and grilles removed (WP 0390 00)
Left cab floor plate removed (WP 0394 00)
Personnel Required Drain cock opened, air brake reservoir pressure released
REMOVAL
1. Remove six screws (1) and washers (2) from treadle valve assembly floor plate (3) on hull (4) and partially remove floor
plate.
0493 00-1
TM 9-2350-247-20-3
REPLACE STOPLIGHT SWITCH (M548A1) — Continued 0493 00
2. Disconnect air stoplight hose (5) from nipple (6). Remove nipple from stoplight switch (7).
3. Disconnect circuit lead 75 (8) and circuit lead 75A (9) from stoplight switch (7).
4. Remove two screws (10), lock nuts (11), and stoplight switch (7) from bottom side of treadle valve assembly floor plate
(3). Discard lock nuts.
0493 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install stoplight switch (1) on bottom side of treadle valve assembly floor plate (2) with two new lock nuts (3) and
screws (4).
2. Connect circuit lead 75 (5) and circuit lead 75A (6) to stoplight switch (1).
3. Install nipple (7) in stoplight switch (1). Connect air stoplight hose (8) to nipple.
0493 00-3
TM 9-2350-247-20-3
4. Install treadle valve assembly floor plate (2) on hull (9) with six washers (10) and screws (11).
1. Close drain cock on air brake reservoir (WP 0491 00).
2. Install left cab floor plate (WP 0394 00).
5. Check stoplight switch for proper operation.
END OF TASK
0493 00-4
TM 9-2350-247-20-3
REPLACE AIR LOW PRESSURE SWITCH (M548A1) 0494 00

INITIAL SETUP:

Unit See your -10

Lock nut (2) Top access cover and grilles removed (WP 0390 00)
Left cab floor plate removed (WP 0394 00)
Personnel Required Drain cock opened, air brake reservoir pressure released
REMOVAL
1. Remove six screws (1) and washers (2) from treadle valve assembly floor plate (3) on hull (4) and partially remove floor
plate.
0494 00-1
TM 9-2350-247-20-3
REPLACE AIR LOW PRESSURE SWITCH (M548A1) — Continued 0494 00
2. Disconnect circuit lead 1B (5) and circuit lead 1C (6) from air low pressure switch (7).
3. Disconnect air low pressure hose (8) from inlet elbow (9). Remove inlet elbow and bushing (10) from air low pressure
switch (7).
4. Remove two screws (11), lock nuts (12), and air pressure switch (7) from bottom side of treadle valve assembly floor
plate (3). Discard lock nuts.
0494 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install air low pressure switch (1) on bottom side of treadle valve assembly floor plate (2) with two new lock nuts (3) and
screws (4).
2. Install bushing (5) and inlet elbow (6) on air low pressure switch (1). Connect air low pressure hose (7) to inlet elbow.
3. Connect circuit lead 1B (8) and circuit lead 1C (9) to air low pressure switch (1).
0494 00-3
TM 9-2350-247-20-3
4. Install treadle valve assembly floor plate (2) on hull (10) with six washers (11) and screws (12).
1. Close drain cock on air brake reservoir (WP 0491 00).
5. Check air low pressure switch for proper operation.
END OF TASK
0494 00-4
TM 9-2350-247-20-3
REPLACE AIR HOSES/TUBES/FITTINGS (M548A1) 0495 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Antiseize compound (WP 0542 00, Item 6) Center seat raised (see your -10)
Sealing compound (WP 0542 00, Item 37) Driver’s seat raised (see your -10)
Grommet (2) Bulkhead protector removed, if installed (WP 0487 00)
Lock nut (5) (M548A1) Power plant rear access covers/door removed
Lock nut (3) (see your -10)
Lock washer (2) Top access cover and grilles removed (WP 0390 00)
Personnel Required Left floor plates removed (WP 0394 00)
Unit Mechanic Drain cock on reservoir opened (WP 0491 00)
REMOVAL
1. Remove six screws (1) and washers (2) from treadle valve floor plate (3) on hull (4) and partially remove floor plate.
0495 00-1
TM 9-2350-247-20-3
REPLACE AIR HOSES/TUBES/FITTINGS (M548A1) — Continued 0495 00
2. Disconnect short emergency hose (1) from tee (2).

3. Disconnect reservoir outlet tube (3) from tee (2) and elbow (4).
4. Remove elbow (4) and safety valve (5) from reservoir outlet tee (6).
5. Remove reservoir outlet tee (6) from reservoir (7).
6. Remove tee (2), bushing (8), and elbow (9) from connector (10).
0495 00-2
TM 9-2350-247-20-3
7. Remove connector (10) from bulkhead (11).

8. Remove cap (12) and connector (13) from hose (14).
9. Disconnect hose (15) from nipple (16).
10. Remove nipple (16), bushing (17) and elbow (18) from connector (19).
11. Remove connector (19), cap (20), and connector (21) from hose (22).
0495 00-3
TM 9-2350-247-20-3
12. Remove two straps (1), hose (2), and hose (3) from cargo door (4).
13. Remove 5 lock nuts (5), screws (6), 10 clamps (7), 5 clips (8) , hose (2), and hose (3) from outside left side of hull.
Discard lock nuts.
0495 00-4
TM 9-2350-247-20-3
14. Remove grommet (1) and grommet (2) from hose (3) and hose (4). Discard grommets.
15. Remove hose (3) from elbow (5). Remove hose (4) from elbow (6).
16. Remove hose (7) from elbow (8). Remove hose (9) from elbow (10).
17. Loosen two jam nuts (11). Separate elbow (5) from elbow (10). Separate elbow (6) from elbow (8).
18. Remove screw (12), lock washer (13), two clamps (14), hose (7), and hose (9) from weld nut (15). Discard lock washer.
0495 00-5
TM 9-2350-247-20-3
19. Disconnect hose (1), hose (2), and hose (3) from bottom side of treadle valve (4).
20. Remove screw (5), lock washer (6), two clamps (7), hose (3), and circuit 1C lead (8) from weld nut (9). Discard lock
washer.
21. Remove hose (3) and connector (10) from gauge (11).
22. Remove lock nut (12), screw (13), clamp (14), clamp (15), hose (3), and circuit 1C lead (8) from support (16). Discard
lock nut.
0495 00-6
TM 9-2350-247-20-3
23. Remove two lock nuts (1), screws (2), clamps (3), and tube (4) from transverse beam (5). Discard lock nuts.
24. Disconnect tube (4) from elbow (6). Remove elbow from reservoir (7).
25. Disconnect tube (4) and hose (8) from union (9).
26. Disconnect hose (8) from compressor (10).
0495 00-7
TM 9-2350-247-20-3
27. Disconnect tube (1) from elbow (2). Remove elbow and adapter (3) from reservoir (4).
28. Disconnect tube (1) from adapter (5). Remove adapter from governor (6).
29. Disconnect hose (7) from adapter (8) and nipple (9). Remove nipple from compressor (10). Remove adapter from
governor (6).
30. Remove tube (11) and drain cock (12) from reservoir (4).
0495 00-8
TM 9-2350-247-20-3
INSTALLATION
NOTE
Before installation, apply a light coat of antiseize compound to outer screw threads and a light
coat of sealing compound to outer pipe threads.
1. Install tube (1) and drain cock (2) on reservoir (3).
2. Install nipple (4) on compressor (5) and adapter (6) on governor (7). Connect hose (8) to adapter and nipple.
3. Install adapter (9) on governor (7). Connect tube (10) to adapter.
4. Install adapter (11) and elbow (12) on reservoir (3). Connect tube (10) to elbow.
0495 00-9
TM 9-2350-247-20-3
0495 00-10
TM 9-2350-247-20-3
5. Connect hose (1) to compressor (2).

6. Connect hose (1) and tube (3) to union (4).
7. Install elbow (5) on reservoir (6). Connect tube (3) to elbow.
8. Install tube (3) on transverse beam (7) with two clamps (8), new lock nuts (9), and screws (10).
0495 00-11
TM 9-2350-247-20-3
9. Install circuit 1C lead (1) and hose (2) on support (3) with clamp (4), clamp (5), new lock nut (6), and screw (7).
10. Install connector (8) on gauge (9). Connect hose (2) to connector.
11. Install circuit 1C lead (1) and hose (2) on weld nut (10) with two clamps (11), new lock washer (12), and screw (13).
12. Connect hose (2), hose (14), and hose (15) to bottom side of treadle valve (16).
0495 00-12
TM 9-2350-247-20-3
13. Install hose (1) and hose (2) on weld nut (3) with two clamps (4), new lock washer (5), and screw (6).
14. Connect elbow (7) to elbow (8) and elbow (9) to elbow (10). Tighten two jam nuts (11).
15. Connect hose (1) to elbow (8) and hose (2) to elbow (10).
16. Connect hose (12) to elbow (9) and hose (13) to elbow (7).
17. Install new grommet (14) and new grommet (15) on hose (12) and hose (13).
0495 00-13
TM 9-2350-247-20-3
18. Install hose (1) and hose (2) on outside left side of hull with 5 clips (9), 10 clamps (10), 5 new lock nuts (11), and
screws (12).
19. Secure hose (1) and hose (2) to cargo door (13) with two straps (8).
0495 00-14
TM 9-2350-247-20-3
20. Install connector (1), cap (2), and connector (3) on hose (4).
21. Install elbow (5), bushing (6), and nipple (7) on connector (1).
22. Connect hose (8) to nipple (7).
23. Install connector (9) and cap (10) on hose (11).
24. Install connector (12) in bulkhead (13).
25. Install elbow (14), bushing (15), and tee (16) on connector (12).
0495 00-15
TM 9-2350-247-20-3
26. Install reservoir outlet tee (17) in reservoir (18).

27. Install safety valve (19) and elbow (20) on reservoir outlet tee (17).
28. Connect reservoir outlet tube (21) to elbow (20) and tee (16).
29. Connect short emergency hose (22) to tee (16).
0495 00-16
TM 9-2350-247-20-3
30. Install treadle valve floor plate (1) on hull (2) with six washers (3) and screws (4).
1. Close drain cock on reservoir.
3. Install power plant rear access covers/door (see your -10).
6. Check trailer air brakes for proper operation.
END OF TASK
0495 00-17/18 blank

TM 9-2350-247-20-3
REPLACE OIL HOSES/FITTINGS (M548A1) 0496 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Antiseize compound (WP 0542 00, Item 6) Bulkhead protector removed, if installed (WP 0487 00)
Container Power plant rear access cover/door removed
Personnel Required (see your -10)
0496 00-1
TM 9-2350-247-20-3
REPLACE OIL HOSES/FITTINGS (M548A1) — Continued 0496 00
REMOVAL
NOTE
Use a container to catch run-off oil when removing oil hoses.
1. Disconnect hose (1) from elbow (2). Remove elbow from compressor (3).
2. Disconnect hose (1) from elbow (4). Remove elbow (4) from engine (5).
3. Disconnect hose (6) from nipple (7). Remove nipple from compressor (3).
4. Disconnect hose (6) from nipple (8). Remove nipple from filler tube (9).
0496 00-2
TM 9-2350-247-20-3
REPLACE OIL HOSES/FITTINGS (M548A1) — Continued 0496 00
INSTALLATION
NOTE
Before installation, apply a light coat of antiseize compound to outer straight screw threads.
1. Install nipple (1) in filler tube (2). Connect hose (3) to nipple.
2. Install nipple (4) in compressor (5). Connect other end of hose (3) to nipple.
3. Install elbow (6) in engine (7). Connect hose (8) to elbow.
4. Install elbow (9) in compressor (5). Connect other end of hose (8) to elbow.
5. Operate air brakes and check for leaks from hoses and fittings.
END OF TASK
0496 00-3/4 blank

TM 9-2350-247-20-3
REPLACE COMPRESSOR DRIVE BELT GUARD (M548A1) 0497 00

INITIAL SETUP:

Unit See your -10

Lock nut (3) Bulkhead protector removed, if material handling kit is
installed (WP 0487 00)
REMOVAL
1. Remove lock nut (1), washer (2), screw (3), guard (4), and filler neck bracket (5) from engine oil filter bracket (6).
Discard lock nut.
2. Remove lock nut (7), washer (8), and guard (4) from bracket (9). Discard lock nut.
3. Remove lock nut (10), two washers (11), screw (12), and guard (4) from bracket (13). Discard lock nut.
0497 00-1
TM 9-2350-247-20-3
REPLACE COMPRESSOR DRIVE BELT GUARD (M548A1) — Continued 0497 00
INSTALLATION
1. Install guard (1) to cover drive belts and pulley on bracket (2) with new lock nut (3), two washers (4), and screw (5).
2. Install guard (1) on bracket (6) with new lock nut (7) and washer (8).
3. Install guard (1) and filler neck bracket (9) on engine oil filter bracket (10) with new lock nut (11), washer (12), and
screw (13).
END OF TASK
0497 00-2
TM 9-2350-247-20-3
ADJUST/ALIGN COMPRESSOR DRIVE PULLEY/BELTS (M548A1) 0498 00

Alignment (page 0498 00-2).
INITIAL SETUP:

Unit
General Mechanic’s Tool Kit (WP 0541 00, Item 57) Bulkhead protector removed, if material handling kit is
Personnel Required installed (WP 0487 00)
Unit Mechanic Power plant rear access cover/door removed
References (see your -10)
See your -10 Compressor drive belt guard removed (WP 0497 00)
ADJUSTMENT
1. Turn adjusting nut (1) to the right to tighten or to the left to loosen compressor drive belts (2).
2. Turn adjusting nut (1) until 5/8 inch (16 mm) deflection is obtained when about 25 lbs (11 kg) force is applied to each
compressor drive belt (2) midway between compressor pulley (3) and drive pulley (4).
0498 00-1
TM 9-2350-247-20-3
ADJUST/ALIGN COMPRESSOR DRIVE PULLEY/BELTS (M548A1) — Continued 0498 00
ALIGN
1. Turn adjusting nut (1) to the left until compressor drive belts (2) are loose.
2. Loosen four compressor mounting screws (5).
3. Position compressor to align compressor pulley (3) with drive pulley (4) in the same plane within 1/8 inch (3 mm) of
each other.
4. Tighten four compressor mounting screws (5).
5. Adjust drive belt tension. Go to Step 1 and Step 2.
1. Install compressor drive belt guard (WP 0497 00).
END OF TASK
0498 00-2
TM 9-2350-247-20-3
REPLACE COMPRESSOR DRIVE PULLEY/BELTS (M548A1) 0499 00

INITIAL SETUP:

Unit See your -10

Bulkhead protector removed, if material handling kit is
Cotter pin installed (WP 0487 00)
Compressor drive belt guard removed (WP 0497 00)
REMOVAL
1. Turn adjusting screw (1) to the left until compressor drive belts (2) are loose. Remove drive belts from compressor
pulley (3) and pulley (4).
0499 00-1
TM 9-2350-247-20-3
REPLACE COMPRESSOR DRIVE PULLEY/BELTS (M548A1) — Continued 0499 00
2. Remove cotter pin (5), nut (6), and washer (7) from compressor shaft (8). Discard cotter pin.
3. Remove compressor pulley (3) from compressor shaft (8).
4. Remove woodruff key (9) from compressor shaft (8).
0499 00-2
TM 9-2350-247-20-3
REPLACE COMPRESSOR DRIVE PULLEY/BELTS (M548A1) — Continued 0499 00
INSTALLATION
1. Insert woodruff key (1) in compressor shaft (2).
2. Install compressor pulley (3) on compressor shaft (2) with washer (4), nut (5), and new cotter pin (6).
3. Install compressor drive belts (7) on compressor pulley (3) and pulley (8).
4. Adjust and align compressor drive belts (WP 0498 00).
1. Install compressor drive belt guard (WP 0497 00).
4. Operate air brakes. Check compressor pulleys and belts for proper operation.
END OF TASK
0499 00-3/4 blank

TM 9-2350-247-20-3
REPLACE AIR STRAINER (M548A1) 0500 00

INITIAL SETUP:

Unit See your -10
Engine lubricating oil (WP 0542 00, Item 13) Carrier blocked (see your -10)
Lock washer (2) Bulkhead protector removed, if material handling kit is
Gasket (2) installed (WP 0487 00)
REMOVAL
1. Remove two screws (1), lock washers (2), air strainer (3), and gasket (4) from compressor (5). Discard gasket and lock
washers.
2. Remove four screws (6), washers (7), cover (8), gasket (9), and element (10) from air strainer (3). Discard gasket.
0500 00-1
TM 9-2350-247-20-3
REPLACE AIR STRAINER (M548A1) — Continued 0500 00
INSTALLATION
1. New or used element (10) needs to be soaked in new or fresh engine lubricating oil and then squeezed out until element
is slightly oiled.
2. Insert element (10) in air strainer (3). Install new gasket (9) and cover (8) on air strainer (3) with four washers (7) and
screws (6).
3. Install air strainer (3) and new gasket (4) on compressor (5) with two new lock washers (2) and screws (1).
END OF TASK
0500 00-2
TM 9-2350-247-20-3
REPLACE AIR BRAKE INSTRUMENT PANEL (M548A1) 0501 00


INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
General Mechanic’s Tool Kit WP 0542 00, Item 57
Lock nut (2)
REMOVAL
1. Disconnect air hose (1) from connector (2). Remove connector from air brake pressure indicator (3).
2. Disconnect circuit 40 lead (M548A1) (4) from air brake instrument panel light (5).
3. Disconnect circuit 1C (6) from air flow pressure warning light (7).
4. Remove two screws (8) lock nuts (9), and air brake instrument panel (10) from instrument panel (11). Discard lock nuts.
0501 00-1
TM 9-2350-247-20-3
REPLACE AIR BRAKE INSTRUMENT PANEL (M548A1) — Continued 0501 00
INSTALLATION
1. Install air brake instrument panel (10) on instrument panel (11) with two new lock nuts (9) and screws (8).
2. Connect circuit 1C lead (6) to air low pressure warning light (7).
3. Connect circuit 40 lead (M548A1) (4) to air brake instrument panel light (5).
4. Install connector (2) on air brake pressure indicator (3). Connect air hose (1) to connector.
2. Check lights and indicator for proper operation.
END OF TASK
0501 00-2
TM 9-2350-247-20-3
REPLACE AIR LOW PRESSURE WARNING LIGHT (M548A1) 0502 00

INITIAL SETUP:

Unit See your -10

REMOVAL
1. Disconnect circuit 1C lead (1) from air low pressure warning light (2).
2. Remove two screws (3) and air low pressure warning light (2) from air brake instrument panel (4).
0502 00-1
TM 9-2350-247-20-3
REPLACE AIR LOW PRESSURE WARNING LIGHT (M548A1) — Continued 0502 00
INSTALLATION
1. Install air low pressure warning light (2) on air brake instrument panel (4) with two screws (3).
2. Connect circuit 1C lead (1) to air low pressure warning light (2).
END OF TASK
0502 00-2
TM 9-2350-247-20-3
REPLACE AIR BRAKE PRESSURE INDICATOR (M548A1) 0503 00


INITIAL SETUP:

Unit See your -10

REMOVAL
1. Disconnect air hose (1) from connector (2). Remove connector from air brake pressure indicator (3).
2. Remove two nuts (4), washers (5), and bracket (6) from rear of air brake instrument panel (7).
3. Remove air brake pressure indicator (3) from front of air brake instrument panel (7).
0503 00-1
TM 9-2350-247-20-3
REPLACE AIR BRAKE PRESSURE INDICATOR (M548A1) — Continued 0503 00
INSTALLATION
1. Install air brake pressure indicator (3) through front of air brake instrument panel (7).
2. Install air brake pressure indicator (3) to air brake instrument panel (7) from rear of panel with bracket (6), two washers
(5), and nuts (4).
3. Install connector (2) on air brake pressure indicator (3). Connect air hose (1) to connector.
2. Operate air brakes.
3. Check air pressure indicator for proper operation.
END OF TASK
0503 00-2
TM 9-2350-247-20-3
REPLACE AIR BRAKE PANEL LIGHT (M548A1) 0504 00

INITIAL SETUP:

Unit See your -10

Unit Mechanic Battery negative lead disconnected (WP 0292 00).
REMOVAL
1. Disconnect circuit 40 lead (M548A1) (1) from air brake panel light (2).
2. Remove two screws (3) and air brake panel light (2) from air brake instrument panel (4).
0504 00-1
TM 9-2350-247-20-3
REPLACE AIR BRAKE PANEL LIGHT (M548A1) — Continued 0504 00
INSTALLATION
1. Install air brake panel light (2) on air brake instrument panel (4) with two screws (3).
2. Connect circuit 40 lead (M548A1) (1) to air brake panel light (2).
1. Connect negative battery lead (WP 0292 00).
END OF TASK
0504 00-2
TM 9-2350-247-20-3
REPLACE TURN SIGNAL LIGHT 0505 00


INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Gasket Equipment Condition
REMOVAL
1. Disconnect circuit 460 (right side) or 461 (left side) lead (1) as required from turn signal light (2).
0505 00-1
TM 9-2350-247-20-3
REPLACE TURN SIGNAL LIGHT — Continued 0505 00
2. Remove lock nut (3), two lock washers (4), stud (5), and turn signal light (6) from bracket (7). Discard lock washers and
lock nut.
3. Remove two screws (1) and washers (2) that secure lens retainer (3), lens (4), and gasket (5) to body (6). Remove lens
retainer, lens, and gasket. Discard gasket.
4. Remove lamp (7) from socket in body (6).
0505 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Install lamp (7) into socket of body (6).
2. Place new gasket (5), lens (4), and lens retainer (3) on body (6). Secure with two washers (2) and screws (1).
3. Place turn signal light (8) on bracket (9). Secure with stud (10), two new lock washers (11) and new lock nut (12). Install
one lock washer on each side of bracket.
0505 00-3
TM 9-2350-247-20-3
4. Connect circuit 460 (right side) or 461 (left side) lead (13) as required to turn signal light (14).
2. Check turn signal lights for proper operation.
END OF TASK
0505 00-4
TM 9-2350-247-20-3
REPLACE BLACKOUT MARKER LIGHT 0506 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Lock nut
Lock washer Engine stopped (see your -10)
0506 00-1
TM 9-2350-247-20-3
REPLACE BLACKOUT MARKER LIGHT — Continued 0506 00
REMOVAL
1. Disconnect circuit 20 lead (1) from blackout marker light (2).
2. Remove lock nut (3), lock washer (4), stud (5), and blackout marker light (6) from bracket (7). Discard lock washer and
lock nut.
0506 00-2
TM 9-2350-247-20-3
REPLACE BLACKOUT MARKER LIGHT — Continued 0506 00
INSTALLATION
1. Place marker light (1) on bracket (2). Secure with stud (3), new lock washer (4) and new lock nut (5). Install one washer
on each side of bracket. Make sure 1-1/2 threads extend through nut after installation.
2. Connect circuit 20 lead (6) to blackout marker light (7).
2. Check blackout marker light for proper operation.
END OF TASK
0506 00-3/4 blank

TM 9-2350-247-20-3
REPLACE BLACKOUT STOPLIGHT-TAILLIGHT 0507 00


INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Lock washer (2)
Lock washer (2)
REMOVAL
NOTE
The blackout stoplight-taillight is like the blackout marker light. Refer to (WP 0278 00) for
maintenance and (WP 0061 00) or (WP 0062 00) for electrical connections.
1. Disconnect circuit 23 lead from blackout stoplight-taillight (1).
2. Remove six nuts (2), two lock washers (3), and six screws (4) that secure bracket (5) to hull. Partially remove bracket
with blackout stoplight-taillight light (1). Discard lock washers.
3. Remove nut (6), two lock washers (7), and stud (8) that secure blackout stoplight-taillight light (1) to bracket (5).
Remove light and bracket. Discard lock washers.
0507 00-1
TM 9-2350-247-20-3
REPLACE BLACKOUT STOPLIGHT-TAILLIGHT — Continued 0507 00
INSTALLATION
1. Place bracket (5) in hull opening. Insert blackout stoplight-taillight (1) in bracket. Secure with two new lock washers
(7), stud (8), and nut (6). Install one washer on each side of bracket. Make sure 1-1/2 threads extend through nut.
2. Place bracket (5) in hull opening. Secure with six screws (4), two new lock washers (3), and six nuts (2).
3. Place fuel compartment vent hose over bracket (5). Connect circuit 23 lead to blackout stoplight-taillight (1).
1. Check blackout stoplight-taillight for proper operation (see your -10).
END OF TASK
0507 00-2
TM 9-2350-247-20-3
REPLACE TURN SIGNAL CONTROL/MOUNT 0508 00

INITIAL SETUP:

Unit See your -10

Lock nut (3)

Personnel Required
Unit Mechanic
REMOVAL
NOTE
Removal and installation procedures for turn signal control/mount is similar for M548A1 and
M548A3. M548A3 turn signal control does not have a bracket. M548A1 is shown.
For M548A1, do Step 4 and Step 1.
1. Remove light lens (1) and lamp (2) from turn signal control handle (3).
2. Disconnect harness connector (4) from turn signal control (5).
3. Loosen clamp (6) that secures turn signal control (5) to mount (7). Remove turn signal control.
4. Remove three lock nuts (8), six washers (9), and three screws (10) that secure mount (7) to range selector housing (11).
Remove mount. Discard lock nuts.
0508 00-1
TM 9-2350-247-20-3
REPLACE TURN SIGNAL CONTROL/MOUNT — Continued 0508 00
INSTALLATION
1. Place mount (7) on turn signal range selector housing (11). Secure with three screws (10), six washers (9), and three new
lock nuts (8).
2. Place turn signal control (5) on mount (7). Secure with clamp (6).
3. Install lamp (2) and light lens (1) in turn signal control handle (3).
4. Connect harness connector (4) to turn signal control (5).
1. Check turn signal control for proper operation.
END OF TASK
0508 00-2
TM 9-2350-247-20-3
REPLACE FLASHER 0509 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Gasket Equipment Condition
REMOVAL
1. Disconnect harness lead (1) from flasher (2).
2. Remove two screws (3) and three lock washers (4) and ground lead (5) that secure flasher (2) to bar (6). Remove flasher.
3. Remove two screws (7) and lock washers (8) that secure bar (6) to hull from outside of carrier. Remove bar and gasket
(9) from inside of carrier. Discard gasket and lock washers.
0509 00-1
TM 9-2350-247-20-3
REPLACE FLASHER — Continued 0509 00
INSTALLATION
1. Place new gasket (9) and bar (6) on inside of carrier. Secure with two screws (7) and new lock washers (8) from outside
of carrier.
2. Place flasher (2) on bar (6). Secure with ground lead (5), three new lock washers (4), and two screws (3). Install one
washer on each side of ground lead terminal.
3. Connect harness lead (1) to flasher (2).
1. Check flasher for proper operation.
END OF TASK
0509 00-2
TM 9-2350-247-20-3
REPLACE REFLECTOR 0510 00


INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
Self-locking screws (2) Engine stopped (see your -10)

REMOVAL
NOTE
Maintenance of left and right reflectors is the same.
1. Remove two self-locking screws (1) and reflector (2) from hull. Discard screws.
0510 00-1
TM 9-2350-247-20-3
REPLACE REFLECTOR — Continued 0510 00
INSTALLATION
1. Place reflector (2) on hull. Secure with two new self-locking screws (1).
END OF TASK
0510 00-2
TM 9-2350-247-20-3
REPLACE TURN SIGNAL FRONT WIRING HARNESS 0511 00

INITIAL SETUP:

Unit Unit Mechanic

Soldering Gun (WP 0541 00, Item 23)
Tiedown strap (32) (WP 0542 00, Item 43) Engine stopped (see your -10)
Tin alloy solder (WP 0542 00, Item 44) Carrier blocked (see your -10)
Grommet (1) Battery negative lead(s) disconnected (WP 0292 00)
Lock washer (2) Left and right stoplight-taillight removed (WP 0278 00)
Terminal (2) Cargo compartment floor plates removed (WP 0393 00)
REMOVAL
1. Disconnect circuit 460 and 461 leads (1) at right and left front turn lamps (2), respectively.
2. Remove terminal (3), sleeve (4), shell (5), and circuit marker band (6) from end of harness leads (1). Discard two
terminals.
0511 00-1
TM 9-2350-247-20-3
REPLACE TURN SIGNAL FRONT WIRING HARNESS — Continued 0511 00
3. Unscrew nut (7) that secures bushing (8) in stuffing tube (9). Slide bushing (8) down on leads and remove circuit 460 and
461 leads (1) from right and left headlight wells, respectively.
4. Remove screw (10) and two lock washers (11) that secure ground lead (12) to flasher unit (13). Disconnect connector
(14) from flasher unit. Discard two lock washers.
5. Remove connector (15) from control assembly (16).
0511 00-2
TM 9-2350-247-20-3
6. Remove connector (1) from switch (2) on back of instrument panel (3).
7. Disassemble connector (1). Remove circuit 22 and 460-461 leads (4 and 5) from connector pins C and J, respectively.
Use soldering gun. Pull leads from connector.
8. Remove circuit 22-461 lead (6) behind connector (1).
9. Disconnect circuit 22-460 lead (7) at trailer wiring harness (8).
10. Remove screw (9) and nut (10) that secure two retainers (11) to bushing (12). Remove circuit 22-460 lead (7) from
bushing and pull lead through two retainers.
0511 00-3
TM 9-2350-247-20-3
11. Disconnect circuit 22-460 lead (13) in left taillight well and pull lead (13) and lead (7) through left hull channel to front
of fuel compartment.
12. Remove 32 tiedown straps (14) that secure front harness (15) to main harness (16) and fuel cut-off control. Discard
tiedown straps.
13. Pull front harness (15) through power plant compartment, grommet (17) in cab floor, and into cab. Remove harness.
Discard grommet.
0511 00-4
TM 9-2350-247-20-3
INSTALLATION
1. Position front wiring harness (1) in cab and route beside main wiring harness (2) through new grommet (3) in cab floor,
power plant compartment, right side of hull, front of fuel compartment, and left hull channel into taillight well.
2. Insert front harness circuit 22-460 lead (4) through two retainers (5). Install lead in bushing (6). Position bushing and
two retainers in hole. Secure with screw (7) and nut (8).
3. Connect circuit 22-460 lead (4) to trailer wiring harness (9).
0511 00-5
TM 9-2350-247-20-3
4. Connect circuit 22-460 lead (10) in left taillight well.

5. Connect circuit 22-461 lead (11) behind connector (12).
6. Thread circuit 22 lead (13) through connector (12), and attach lead to pin C. Use solder and soldering gun.
7. Thread circuit 460-461 lead (14) through connector (12) and attach lead to pin J. Use solder and soldering gun.
8. Assemble connector (12) and attach to switch (15) on back of instrument panel (16).
0511 00-6
TM 9-2350-247-20-3
9. Attach connector (1) to control assembly (2).

10. Attach connector (3) to flasher unit (4) and secure ground lead (5) to flasher unit with two new lock washers (6) and
screw (7).
11. Thread circuit 461 lead (8) through stuffing tube (9), bushing (10), and nut (11) into left headlight well. Thread circuit
460 lead (8) through bushing (10) and nut (11) into right headlight well. Slide bushing up on leads and secure nut.
0511 00-7
TM 9-2350-247-20-3
12. Install circuit marker band (12), shell (13), sleeve (14), and new terminal (15) on end of each harness lead (8).
13. Connect circuit 461 lead (8) to left turn indicator lamp (16) and circuit 460 lead (8) to right indicator lamp.
14. Secure front wiring harness (17) to main harness (18) and fuel cutoff control with 32 new tiedown straps (19) installed
next to each clamp, or route through front and main harness clamps.
1. Install left and right stoplight-taillight (WP 0278 00).
3. Install cargo compartment floor plates (WP 0393 00).
END OF TASK
0511 00-8
TM 9-2350-247-20-3
REPLACE TURN SIGNAL REAR WIRING HARNESS 0512 00


INITIAL SETUP:

Unit See your -10

Tiedown strap (7) (WP 0542 00, Item 43) Carrier blocked (see your -10)
Connector (2) Cargo compartment floor plates removed (WP 0393 00)
Personnel Required Battery negative lead(s) disconnected (WP 0292 00)
Unit Mechanic Left and right stoplight-taillights removed (WP 0278 00)
REMOVAL
1. Disconnect rear harness circuit 21 lead (1) and circuit 22-460 lead (2) from right taillight leads. Remove lead connector
(3), sleeve (4), and shell (5) from each lead. Discard two connectors.
2. Remove screw (6), nut (7), two right spacer plates (8), and bushing (9). Remove rear harness circuit 21 and 22-460 lead
(1) and 22–460 lead (2) from bushing. Pull leads through spacer plates.
3. Disconnect circuit 22-460 lead (10) in left taillight.
4. Disconnect circuit 21 lead (11) and circuit 21 lead (12) in left taillight.
0512 00-1
TM 9-2350-247-20-3
REPLACE TURN SIGNAL REAR WIRING HARNESS — Continued 0512 00
5. Remove screw (13), nut (14), two spacer plates (15), and bushing (16). Remove circuit 21 lead (12) from bushing. Pull
lead through spacer plates.
6. Remove and discard seven tiedown straps (17) and rear wiring harness (18) from main wiring harness (19) at front of
fuel compartment.
7. Pull rear harness circuit 21 and 22-460 lead (1) and 22–460 lead (2) through right hull channel to front of fuel
compartment.
8. Pull rear wiring harness (18) through left hull channel into left taillight. Remove harness.
0512 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Position rear wiring harness (1) in left taillight. Route rear harness circuit 21 and 22-460 lead (2) and 22–460 lead (3)
through left hull channel across front of fuel compartment along main wiring harness (4).
2. Thread rear harness circuit 21 and 22-460 lead (2) and 22–460 lead (3) through right hull channel into right taillight.
3. Insert rear harness circuit 21 lead (2) and circuit 22-460 lead (3) through two right taillight spacer plates (5). Install leads
in bushing (6). Secure bushing and two spacer plates to hole in taillight with screw (7) and nut (8).
4. Install lead connector shell (9), sleeve (10), and new connector (11) on rear harness circuit 21 and 22-460 lead (2) and
22–460 lead (3). Connect leads at right taillight.
0512 00-3
TM 9-2350-247-20-3
5. Insert circuit 21 lead (12) through two left taillight spacer plates (13). Install lead in bushing (14). Secure bushing and
two spacer plates to hole in taillight with screw (15) and nut (16).
6. Install circuit 21 lead (12) in left taillight.
7. Install rear-to-main harness circuit 21 lead (17) in left taillight.
8. Install front-to-rear harness circuit 22-460 lead (18) in left taillight.
9. Secure rear wiring harness (1) to main wiring harness (4) along front of fuel compartment with seven new tiedown straps
(19). Install adjacent to each existing cable clamp or route harness through main wiring harness clamps.
1. Install left and right stoplight-taillights (WP 0278 00).
END OF TASK
0512 00-4
TM 9-2350-247-20-3
REPLACE CALIBER .50 MACHINE GUN MOUNT 0513 00

INITIAL SETUP:

Unit See your -10
TM 9-1005-245-13&P
Materials/Parts
Spring pin (2)
Personnel Required
Unit Mechanic
REMOVAL
1. Remove gun mount (see your -10).
2. Remove cartridge deflector, ammo straps, and backrest from ring mount and supports (WP 0514 00).
3. Remove ring mount and supports from carrier (WP 0514 00).
0513 00-1
Change 1
TM 9-2350-247-20-3
REPLACE CALIBER .50 MACHINE GUN MOUNT — Continued 0513 00
DISASSEMBLY
1. Disassemble ring mount. See TM 9-1005-245-13&P.
2. Release cam (1). Remove ammo tray (2) from ammo tray bracket (3).
3. Remove three screws (4), nuts (5), and ammo tray bracket (3) from cradle (6).
4. Remove chain on front locking pin (7) from rivet (8). Remove locking pin (7) from cradle (6).
0513 00-2
Change 1
TM 9-2350-247-20-3
5. Remove chain on locking pin (9) from rivet (10). Remove locking pin (9) from pintle (11).
6. Remove chain on rear locking pin (12) from one bolt (13). Remove locking pin (12) from cradle (6) and spacer cradle
(14).
7. Remove two bolts (13), washers (15), nuts (16), and spacer cradle (14) from cradle (6).
8. Remove two spring pins (17) from holes in cradle (6). Remove two setscrews (18) from pintle (11). Separate pintle
from cradle. Discard spring pins.
0513 00-3
Change 1
TM 9-2350-247-20-3
ASSEMBLY
1. Install spacer cradle (1) on cradle (2) with two bolts (3), washers (4), and nuts (5).
2. Install rear locking pin (6) with chain attached through cradle (2) and spacer cradle (1). Attach end of chain to one
bolt (3). Tighten both bolts.
3. Place cradle (2) on pintle (7). Secure with two setscrews (8).
4. Align holes in setscrews (8) with holes in top of cradle (2). Install two new spring pins (9) to secure setscrews (8).
0513 00-4
Change 1
TM 9-2350-247-20-3
5. Install front locking pin (10) with chain attached in cradle (2). Secure end of chain to rivet (11) on cradle (2).
6. Install locking pin (12) with chain attached through pintle (7) and cradle (2). Secure end of chain to rivet (13) on pintle
(7).
7. Install ammo tray bracket (14) on cradle (2) with three screws (15) and nuts (16).
8. Place ammo tray (17) on ammo tray bracket (14). Secure with cam (18).
0513 00-5
Change 1
TM 9-2350-247-20-3
INSTALLATION
1. Install ring mount on carrier (WP 0514 00).
2. Install cartridge deflector, ammo straps, and backrest on ring mount (WP 0514 00).
3. Install assembled cradle (2) and pintle (7) on ring mount (see your -10).
END OF TASK
0513 00-6
Change 1
TM 9-2350-247-20-3
REPLACE M66 RING MOUNT KIT 0514 00

INITIAL SETUP:

Unit Unit Mechanic
Helper (H)
Socket Wrench Set (WP 0541 00, Item 65) See your -10
Torque Wrench (WP 0541 00, Item 72) TM 9-1005-245-13&P
Lifting Device
Equipment Condition
Nonelectrical wire (WP 0542 00, Item 27) Carrier blocked (see your -10)
Cotter pin (2) Cargo compartment floor plates removed (WP 0393 00)
Locknut (2)
Locknut (4)
Locknut (12)
0514 00-1
Change 1
TM 9-2350-247-20-3
REPLACE M66 RING MOUNT KIT — Continued 0514 00
REMOVAL
1. Remove machine gun mount (WP 0513 00 or WP 0515 00).
2. Remove two cotter pins (1), pins (2), and backrest (3) from brackets (4) on ring mount (5). Discard cotter pins.
3. Remove two setscrews (6), lock wire (7), and cartridge deflector (8) from deflector support (9). Separate lock wire
(7) from deflector (8) and discard lock wire.
4. Remove two locknuts (10), washers (11), screws (12), and support (9) from gun mount (13). Discard locknuts.
5. Remove straps (14) from ammo box holders (15).
CAUTION
Ring mount weighs 314 lb (143 kg). Make sure lifting device is strong enough.
6. Secure suitable lifting device to ring mount (5).
0514 00-2
Change 1
TM 9-2350-247-20-3
7. Remove eight locknuts (1), washers (2), and screws (3) from two front supports (4) and ring mount (5). Discard locknuts.
8. Remove four screws (6), washers (7), and locknuts (8) from two rear supports (9) and ring mount (5). Discard locknuts.
9. Remove ring mount (5) with suitable lifting device.
10. Remove four screws (10), locknuts (11), six washers (12), and two rear supports (9) from transverse beam. Discard
locknuts.
0514 00-3
Change 1
TM 9-2350-247-20-3
11. Remove eight screws (13), washers (14), and two front supports (4) from hull.
12. Remove cargo compartment floor plates (WP 0388 00). Remove eight screws (provided with kit) and two lifting eyes
(15) from stowage.
NOTE
See TM 9-1005-245-13&P for disassembly of gun mount ring.
13. (H) Install lifting eyes (15) on hull with original eight screws (16). TIGHTEN SCREWS TO 185 LB-FT (251 N·M)
TORQUE.
0514 00-4
Change 1
TM 9-2350-247-20-3
INSTALLATION
1. Remove eight screws (1) and two front lifting eyes (2) from hull.
NOTE
Eight screws are provided in kit for stowage of lifting eyes.
2. (H) Use screws provided. Install lifting eyes (2) under cargo floor plate for stowage.
3. Place rear ring mount supports (3) on transverse beam. Secure each support with two screws (4), three washers (5), and
two locknuts (6). TIGHTEN SCREWS TO 185 LB-FT (251 N·M) TORQUE.
0514 00-5
Change 1
TM 9-2350-247-20-3
4. Place front ring mount supports (1) on hull. Secure each support (1) with four screws (2) and washers (3). TIGHTEN
SCREWS TO 185 LB-FT (251 N·M) TORQUE.
CAUTION
Ring mount weighs 314 lb (143 kg). Make sure lifting device is strong enough.
5. Raise ring mount (4) with suitable lifting device. Place ring mount on support (1) and support (5). Align holes.
5. Secure rear supports (5) to ring mount (4) with four screws (6), washers (7), and locknuts (8). TIGHTEN SCREWS TO
65 LB-FT (88 N·M) TORQUE.
6. Secure front supports (1) to ring mount (4) with eight screws (9), washers (10), and new locknuts (11). TIGHTEN
SCREWS TO 65 LB-FT (88 N·M) TORQUE.
7. Secure straps (12) around ammo box holders (13).
0514 00-6
Change 1
TM 9-2350-247-20-3
8. Install machine gun mount (WP 0513 00 or WP 0515 00).

9. Install deflector support (1) on gun mount (2) with two screws (3), washers (4), and new locknuts (5).
10. Install new lock wire (6) in cartridge deflector (7). Put ends of lock wire in holes on deflector holder (1). Secure with
two setscrews (8).
NOTE
See your -10 for adjustment of equilibrator spring.
11. Install backrest (9) on brackets (10) with two pins (11). Secure with two new cotter pins (12).
END OF TASK
0514 00-7/8 blank

Change 1
TM 9-2350-247-20-3
REPLACE 7.62 MM MACHINE GUN MOUNT 0515 00

INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Lubricating oil preservative (WP 0542 00, Item 15) Equipment Condition
Nonelectrical wire (WP 0542 00, Item 27) Engine stopped (see your -10)
Cotter pin Carrier blocked (see your -10)
REMOVAL
1. Loosen pintle clamping screw (1). Remove 7.62 mm machine gun mount from ring mount carriage (2).
0515 00-1
TM 9-2350-247-20-3
REPLACE 7.62 MM MACHINE GUN MOUNT — Continued 0515 00
DISASSEMBLY
1. Remove lock wire (3) and four screws (4) that secure holder (5) to cradle (6). Remove cradle. Discard lock wire.
2. Remove cotter pin (7), nut (8), screw (9), and washer (10) that secure platform (11) and cradle (6) to pintle (12).
Separate pintle from platform and cradle. Discard cotter pin.
3. Remove lock wire (13) and three screws (14) that secure cradle (6) to platform (11). Discard lock wire.
0515 00-2
TM 9-2350-247-20-3
ASSEMBLY
1. Place cradle (1) on platform (2). Install three screws (3). Secure screws with new lock wire (4).
2. Place platform (2) and cradle (1) on pintle (5). Make sure pivot holes are aligned.
3. Install washer (6), screw (7), and nut (8) to secure platform (2) and cradle (1) on pintle (5). Tighten nut by hand.
4. Back nut (8) off to align notches with hole in screw (7). Install new cotter pin (9) in nut.
5. Place holder (10) on cradle (1). Secure with four screws (11) and new lock wire (12).
0515 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Install 7.62 mm machine gun mount in ring mount carriage (13). Secure with pintle clamping screw (14).
END OF TASK
0515 00-4
TM 9-2350-247-20-3
CHAPTER 23
FOR GAUGES
WORK PACKAGE INDEX

Title Sequence No.
REPLACE SPEEDOMETER.............................................................................................................................................0516 00
REPLACE SPEEDOMETER CABLE HOUSING AND ADAPTER...............................................................................0517 00
REPLACE SPEEDOMETER CABLE...............................................................................................................................0518 00
REPLACE TACHOMETER..............................................................................................................................................0519 00
REPLACE TACHOMETER CABLE HOUSING AND ADAPTER (M548A1)..............................................................0520 00
REPLACE TACHOMETER CABLE HOUSING AND ADAPTER (M548A3)..............................................................0521 00
REPLACE TACHOMETER CABLE (M548A1)..............................................................................................................0522 00
REPLACE TACHOMETER CABLE (M548A3)..............................................................................................................0523 00
TM 9-2350-247-20-3
REPLACE SPEEDOMETER 0516 00


INITIAL SETUP:

Unit See your -10
Equipment Condition
Materials/Parts
Gasket Engine stopped (see your -10)
Unit Mechanic Instrument panel partially removed (WP 0256 00)
REMOVAL
NOTE
Instrument panel switches, indicators, and controls will vary between the M548A1 and
M548A3. M548A1 instrument panel is shown.
1. Disconnect flexible shaft assembly (1) and gasket (2) from speedometer (3). Discard gasket.
2. Remove two nuts (4), washers (5), and bracket (6) from speedometer (3) and instrument panel (7). Remove speedometer
from instrument panel.
0516 00-1
TM 9-2350-247-20-3
REPLACE SPEEDOMETER — Continued 0516 00
INSTALLATION
1. Place speedometer (3) in instrument panel (7). Secure with bracket (6), two washers (5), and nuts (4).
2. Install new gasket (2) in speedometer flexible shaft assembly (1). Connect speedometer flexible shaft assembly to
speedometer (3).
1. Install instrument panel (WP 0256 00).
END OF TASK
0516 00-2
TM 9-2350-247-20-3
REPLACE SPEEDOMETER CABLE HOUSING AND ADAPTER 0517 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Grommet Instrument panel partially removed (WP 0256 00)
Tablock washer (4)
Left cab floor plate removed (WP 0394 00) or
Preformed packing
(WP 0395 00)
Personnel Required Speedometer cable housing disconnected from
Unit Mechanic speedometer (WP 0516 00)
REMOVAL
1. Disconnect speedometer cable housing (1) from left final drive shaft adapter (2).
NOTE
2. Remove three screws (3), washers (4), and clamps (5) from weld nuts (6) that secure speedometer cable housing (1).
3. Remove nut (7), washer (8), screw (9), and clamp (10) securing speedometer shaft (11) to hand brake bracket.
0517 00-1
TM 9-2350-247-20-3
REPLACE SPEEDOMETER CABLE HOUSING AND ADAPTER — Continued 0517 00
4. Pull speedometer cable housing (1) through grommet (12) located in bulkhead (13) and out of carrier.
5. Remove grommet (12) from bulkhead (13). Discard grommet.
6. Remove four screws (14) and tablock washers (15) from left final drive shaft adapter (2) and final drive (16). Discard
tablock washers.
7. Remove left final drive shaft adapter (2) and preformed packing (17) from final drive (16). Discard preformed packing.
0517 00-2
TM 9-2350-247-20-3
INSTALLATION
NOTE
See WP 0128 00 for grease used on final drive shaft adapter.
1. Install new preformed packing (1) in left final drive shaft adapter (2). Place adapter on final drive (3) and engage drive
shaft of adapter in final drive.
2. Secure left final drive shaft adapter (2) to left final drive (3) with four new tablock washers (4) and screws (5). Bend tabs
of washers to secure screws.
3. Install new grommet (6) in bulkhead (7). Insert speedometer cable housing (8) through grommet to left final drive shaft
adapter (2).
4. Connect speedometer cable housing (8) to left final drive shaft adapter (2).
0517 00-3
TM 9-2350-247-20-3
NOTE
5. Secure speedometer cable housing (8) to hull weld nuts (9) with three clamps (10), washers (11), and screws (12).
6. Position speedometer shaft (13) on hull and secure with clamp (14), screw (15), washer (16), and nut (17).
1. Install left cab floor plate (WP 0394 00) or (WP 0395 00).
3. Connect speedometer cable housing to speedometer (WP 0516 00).
END OF TASK
0517 00-4
TM 9-2350-247-20-3
REPLACE SPEEDOMETER CABLE 0518 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Aircraft Grease (WP 0542 00, Item 3) Instrument panel partially removed (WP 0256 00)
Personnel Required Left cab floor plate removed (WP 0394 00) or
REMOVAL
NOTE
Speedometer cable can be removed without removing speedometer or speedometer cable
housing.
1. Disconnect speedometer cable housing (1) from left final drive adapter (2).
2. Disconnect speedometer cable housing (1) from speedometer (3) at instrument panel (4).
0518 00-1
TM 9-2350-247-20-3
REPLACE SPEEDOMETER CABLE — Continued 0518 00
3. Remove slotted washer (5) and washer (6) from left final drive adapter (2) end of speedometer cable (7).
4. Pull speedometer cable (7) out of speedometer cable housing (1) at instrument panel (4) end. Check gasket (8) in cable
housing. Replace gasket if necessary.
INSTALLATION
1. Coat speedometer cable (1) with grease (WP 0128 00).
2. Install speedometer cable (1) in speedometer cable housing (2) at instrument panel (3) end. Install gasket (4), if replaced,
in cable housing.
3. Install slotted washer (5) and washer (6) on speedometer cable (1) at left final drive adapter (7) end.
0518 00-2
TM 9-2350-247-20-3
REPLACE SPEEDOMETER CABLE — Continued 0518 00
4. Connect speedometer cable housing (2) to left final drive adapter (7).
5. Connect speedometer cable housing (2) to speedometer (8) at instrument panel (3).
1. Install cab left floor plate (WP 0394 00) or (WP 0395 00).
END OF TASK
0518 00-3/4 blank

TM 9-2350-247-20-3
REPLACE TACHOMETER 0519 00

INITIAL SETUP:

Unit See your -10
Equipment Condition
Materials/Parts
Gasket Engine stopped (see your -10)
Unit Mechanic Instrument panel partially removed (WP 0256 00)
REMOVAL
NOTE
Instrument panel switches, indicators, and controls will vary between the M548A1 and
M548A3. M548A1 instrument panel is shown.
1. Disconnect flexible shaft assembly (1) and gasket (2) from tachometer (3). Discard gasket.
2. Remove two nuts (4), washers (5), and bracket (6) from tachometer (3) and instrument panel (7). Remove tachometer
from instrument panel.
0519 00-1
TM 9-2350-247-20-3
REPLACE TACHOMETER — Continued 0519 00
INSTALLATION
1. Place tachometer (3) in instrument panel (7). Secure with bracket (6), two washers (5), and nuts (4).
2. Install new gasket (2) in flexible shaft assembly (1). Connect flexible shaft assembly to tachometer (3).
END OF TASK
0519 00-2
TM 9-2350-247-20-3
REPLACE TACHOMETER CABLE HOUSING AND ADAPTER (M548A1) 0520 00

INITIAL SETUP:

Unit See your -10

Instrument panel partially removed (WP 0256 00)
Nonelectrical wire (WP 0542 00, Item 27)
Grommet Left cab floor plate removed (WP 0394 00)
Lock nut (4) Power plant rear access covers/door removed
(see your -10)
Personnel Required Tachometer cable housing disconnected from tachometer
0520 00-1
TM 9-2350-247-20-3
REPLACE TACHOMETER CABLE HOUSING AND ADAPTER (M548A1) — Continued 0520 00
REMOVAL
NOTE
If material handling kit is installed, remove bulkhead protector (WP 0487 00).
1. Disconnect tachometer cable housing (1) from tachometer drive adapter (2) on engine.
2. Remove tachometer cable housing (1), four screws (3), washers (4), and clamps (5) from hull weld nuts (6).
3. Pull tachometer cable housing (1) from two clips (7) on lower bulkhead panel (8).
4. Pull tachometer cable housing (1) through grommet (9) located in bulkhead (10) and out of carrier.
0520 00-2
TM 9-2350-247-20-3
5. Remove grommet (9) from bulkhead (10). Discard grommet.

6. Remove lock wire (11) from drive adapter (2) and engine adapter plate (12). Discard lock wire.
7. Remove drive adapter (2) from engine adapter plate (12).
8. Remove four screws (13), lock nuts (14), washers (15), and two clips (7) from lower bulkhead panel (8). Discard lock
nuts.
0520 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Attach drive adapter (1) to engine adapter plate (2). Secure with new lock wire (3).
2. Install new grommet (4) in bulkhead (5). Insert tachometer cable housing (6) through grommet to drive adapter (1).
3. Connect tachometer cable housing (6) to drive adapter (1) on engine.
0520 00-4
TM 9-2350-247-20-3
4. Connect tachometer cable housing to tachometer (WP 0519 00).

5. Secure tachometer cable housing (6) to hull weld nuts (7) with four clamps (8), washers (9), and screws (10).
6. Install two clips (11) on lower bulkhead panel (12) with four screws (13), washers (14), and new lock nuts (15).
NOTE
After completing this step, if material handling kit is installed, install bulkhead protector
(WP 0487 00).
7. Push tachometer cable housing (6) firmly into two clips (11).
1. Install power plant rear access covers/door (see your -10).
END OF TASK
0520 00-5/6 blank

TM 9-2350-247-20-3
REPLACE TACHOMETER CABLE HOUSING AND ADAPTER (M548A3) 0521 00

INITIAL SETUP:

Unit See your -10

Nonelectrical wire (WP 0542 00, Item 27)
Instrument panel partially removed (WP 0256 00)
Grommet
Lock washer (4) Driver’s side batteries removed on left side
(WP 0293 00)
Personnel Required Driver’s floor plate removed on left side (WP 0395 00)
REMOVAL
1. Locate tachometer (1) and tachometer drive adapter (2) in carrier.
2. Remove tachometer cable (3) from tachometer (1).
0521 00-1
TM 9-2350-247-20-3
3. Remove four screws (1), lock washers (2), and clamps (3) that secure tachometer cable (4) to four weld nuts (5). Discard
lock washers.
4. Remove grommet (6) from tachometer cable (4) at battery compartment bulkhead (7). Discard grommet.
5. Remove tachometer cable (4) from tachometer drive adapter (8).
6. Remove tachometer cable (4) from power plant compartment, battery compartment bulkhead (7), and under driver’s floor
plate in carrier.
7. Remove lock wire (9) and tachometer drive adapter (8) from engine connector (10). Discard lock wire.
CLEANING
1. Inspect threaded areas on tachometer drive adapter for burrs, nicks, or other damage. If damage can not be repaired,
replace adapter.
2. Inspect tachometer cable for damage, cracks, breaks, cuts, deteriorated rubber, or damaged end fittings. If defects can not
be repaired, replace cable.
INSTALLATION
1. Install tachometer drive adapter (1) on engine connector (2). Secure with new lock wire (3).
0521 00-2
TM 9-2350-247-20-3
2. Insert tachometer cable (4) under driver’s floor plate in carrier. Route through battery compartment bulkhead (5) and into
power plant compartment.
3. Place new grommet (6) on tachometer cable (4) at battery compartment bulkhead (5).
4. Place tachometer cable (4) on four weld nuts (7). Secure with four clamps (8), new lock washers (9) and screws (10).
5. Connect tachometer cable (4) to tachometer drive adapter (1) and tachometer (11).
1. Install driver’s side batteries on left side (WP 0293 00).
3. Install driver’s floor plate on left side (WP 0395 00).
END OF TASK
0521 00-3/4 blank

TM 9-2350-247-20-3
REPLACE TACHOMETER CABLE (M548A1) 0522 00

INITIAL SETUP:

Unit See your -10
Aircraft grease (WP 0542 00, Item 3) Carrier blocked (see your -10)
Personnel Required Instrument panel partially removed (WP 0256 00)
Unit Mechanic Power plant rear access door removed (see your -10)
REMOVAL
NOTE
If material handling kit is installed, remove bulkhead protector (WP 0487 00). Tachometer
cable can be removed without removing tachometer or tachometer cable housing.
1. Disconnect tachometer cable housing (1) from tachometer drive adapter (2) on engine.
2. Disconnect tachometer cable housing (1) from tachometer (3) on instrument panel (4).
0522 00-1
TM 9-2350-247-20-3
REPLACE TACHOMETER CABLE (M548A1) — Continued 0522 00
3. Remove slotted washer (5) and washer (6) from tachometer cable (7) at tachometer drive adapter (2) end.
4. Pull tachometer cable (7) out of tachometer cable housing (1) at instrument panel (4) end. Check gasket (8) in cable
housing. Replace gasket if necessary.
0522 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Coat tachometer cable (1) with grease (WP 0128 00).
2. Install tachometer cable (1) in tachometer cable housing (2) at instrument panel (3) end. Install gasket (4), if replaced, in
cable housing.
3. Install slotted washer (5) and washer (6) on tachometer cable (1) at tachometer drive adapter (7) end of tachometer cable.
4. Connect tachometer cable housing (2) to tachometer (8) on instrument panel (3).
NOTE
After completing this step, if material handling kit is installed, install bulkhead protector
(WP 0487 00).
5. Connect tachometer cable housing (2) to tachometer drive adapter (7).

END OF TASK
0522 00-3/4 blank

TM 9-2350-247-20-3
REPLACE TACHOMETER CABLE (M548A3) 0523 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
GAA grease (WP 0542 00, Item 14) Both battery negative leads disconnected (WP 0292 00)
Personnel Required Instrument panel partially removed (WP 0256 00)
REMOVAL
NOTE
The instrument panel must be partially removed to access tachometer cable. Tachometer cable
can be removed without removing tachometer or tachometer cable housing.
1. Locate tachometer (1) and tachometer drive adapter (2). Tachometer cable (3) is connected to the tachometer at one end
and to the tachometer drive adapter on the other end.
2. Remove tachometer cable (3) from tachometer (1) and tachometer drive adapter (2).
0523 00-1
TM 9-2350-247-20-3
3. Pull cable core (1) from tachometer drive adapter (2) end of tachometer cable (3), as far out as possible. Remove core
lock (4).
4. Remove cable core (1) from tachometer (5) end of tachometer cable (3).
CLEANING
1. Inspect cable core for worn or loose end fittings and broken or marred strands. Replace damaged or defective core.
0523 00-2
TM 9-2350-247-20-3
INSTALLATION
1. Pack cable core (1) with grease.
2. Insert cable core (1) into tachometer cable (3). Insert cable at end of tachometer (5).
3. Pull end of cable core (1) from tachometer cable (3) at end of tachometer drive adapter (2). Attach core lock (4) to secure
cable core.
4. Connect tachometer cable (3) to tachometer drive adapter (2) and to tachometer (6).
END OF TASK
0523 00-3/4 blank

TM 9-2350-247-20-3
CHAPTER 24
FOR FIRE EXTINGUISHER SYSTEM
WORK PACKAGE INDEX

Title Sequence No.
REPLACE NOZZLES, TUBES, AND FITTINGS (NEW CONFIGURATION).............................................................0524 00
REPLACE NOZZLES, TUBES, AND FITTINGS (OLD CONFIGURATION)..............................................................0525 00
REPLACE CARBON DIOXIDE (CO2) CYLINDER.......................................................................................................0526 00
REPLACE FYR-FYTER CONTROL VALVE..................................................................................................................0527 00
REPLACE WALTER KIDDE CONTROL VALVE...........................................................................................................0528 00
REPLACE/REPAIR PORTABLE FIRE EXTINGUISHER PANEL ASSEMBLY (M548A3).........................................0529 00
TM 9-2350-247-20-3
REPLACE NOZZLES, TUBES, AND FITTINGS (NEW CONFIGURATION) 0524 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Lock nut (3) Driver’s seat raised (see your -10)
Personnel Required Battery negative lead disconnected (WP 0292 00)
REMOVAL
1. Remove two nozzles (1) from tube (2) and tube (3).
2. Remove three lock nuts (4), washers (5), and screws (6) that secure three clamps (7) to carrier bulkhead. Discard lock
nuts.
3. Remove tube (2) from tee (8).
0524 00-1
TM 9-2350-247-20-3
REPLACE NOZZLES, TUBES, AND FITTINGS (NEW CONFIGURATION) — Continued 0524 00
4. Remove tube (3) from tee (8).

5. Remove tee (8) from tube (13).
6. Loosen nut (14) that secures tube (13) to cylinder (15).
7. Remove lock nut (16), washer (17), and screw (18) that secure clamp (19) to carrier bulkhead. Discard lock nut. Remove
tube (13).
8. Remove boot (20) from carrier bulkhead.
0524 00-2
TM 9-2350-247-20-3
INSTALLATION
NOTE
Inspect lines, tubes, nozzles, and clamps for damage. Replace as needed.
1. Install boot (1) on carrier bulkhead.

2. Install screw (2), washer (3), and new lock nut (4) securing clamp (5) to carrier bulkhead. Install tube (6).
3. Tighten nut (7) that secures tube (6) to cylinder (8).
4. Install tee (9) on tube (6).
5. Install tube (10) on tee (9).
0524 00-3
TM 9-2350-247-20-3
6. Install tube (15) on tee (9).

7. Install three screws (16), washers (17), and new lock nuts (18) securing three clamps (19) to carrier bulkhead.
8. Install two nozzles (20) on tube (15) and tube (10).
END OF TASK
0524 00-4
TM 9-2350-247-20-3
REPLACE NOZZLES, TUBES, AND FITTINGS (OLD CONFIGURATION) 0525 00

INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Lock nut (2) Driver’s seat raised (see your -10)
Personnel Required Both battery negative leads disconnected (WP 0292 00)
REMOVAL
1. Remove nozzle (1) from tube (2).
2. Remove lock nut (3), washer (4), screw (5), and clamp (6) from carrier bulkhead. Discard lock nut.
3. Loosen nut (7) that secures tube (2) to cylinder (8).
4. Remove lock nut (9), washer (10), screw (11), and clamp (12) from carrier bulkhead. Discard lock nut. Remove tube (2).
5. Remove boot (13) from carrier bulkhead.
0525 00-1
TM 9-2350-247-20-3
REPLACE NOZZLES, TUBES, AND FITTINGS (OLD CONFIGURATION) — Continued 0525 00
INSTALLATION
1. Install boot (1) on carrier bulkhead.
2. Install screw (2), washer (3), clamp (4), and new lock nut (5) on carrier bulkhead. Insert tube (6).
3. Tighten nut (7) that secures tube (6) to cylinder (8).
4. Install screw (9), washer (10), clamp (11), and new lock nut (12) on carrier bulkhead.
5. Install nozzle (13) on tube (6).
END OF TASK
0525 00-2
TM 9-2350-247-20-3
REPLACE CARBON DIOXIDE (CO2) CYLINDER 0526 00

INITIAL SETUP:

Unit See your -10
Personnel Required Driver’s seat raised (see your -10)
0526 00-1
TM 9-2350-247-20-3
REPLACE CARBON DIOXIDE (CO2) CYLINDER — Continued 0526 00
REMOVAL
1. Loosen nut (1) that secures control valve (2) to cylinder (3). Remove control.
2. Loosen nut (4) that secures tube (5) to cylinder (3). Remove tube.
WARNING
You could be injured if cylinder discharges when it is out of its mounting brackets or is
dropped. Discharge cylinder completely before removing it from its mount. Handle cylinders
with great care.
3. Loosen two nuts (6) that secure two clamps (7) around cylinder (3). Remove cylinder.
4. Remove four cotter pins (8) and pins (9) that secure two clamps (7) to four brackets (10). Remove clamps. Discard
cotter pins.
5. Remove four bumpers (11) from four brackets (10).
0526 00-2
TM 9-2350-247-20-3
0526 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Install four bumpers (1) in four brackets (2).
WARNING
You could be injured if cylinder discharges when it is out of its mounting brackets or is
dropped. Reset or close control valve prior to installing it on the cylinder. Handle cylinders
with great care.
NOTE
The carbon dioxide (CO2 )cylinder has a 5 pound (2 kg) capacity with a maximum weight of 18
pounds (8 kg). Weigh cylinder before installation. If weight loss is more than 10 percent (2
pounds) (1 kg), replace cylinder with a fully charged one.
2. Align two clamps (3) with holes in four brackets (2). Secure two clamps with four pins (4) and four new cotter pins (5).
3. Place cylinder (6) in four brackets (2). Secure with two clamps (3) and tighten two nuts (7).
4. Install tube (8) on cylinder (6). Secure with nut (9).
5. Install control valve (10) on cylinder (6). Secure with nut (11).
0526 00-4
TM 9-2350-247-20-3
END OF TASK
0526 00-5/6 blank

TM 9-2350-247-20-3
REPLACE FYR-FYTER CONTROL VALVE 0527 00

INITIAL SETUP:

Unit See your -10
Materials/Parts
Lock nut
Wire seal (.020 copper) Driver’s seat raised (see your -10)
0527 00-1
TM 9-2350-247-20-3
REPLACE FYR-FYTER CONTROL VALVE — Continued 0527 00
REMOVAL
1. Loosen nut (1) that secures tube (2) to adapter (3).
2. Loosen nut (4) that secures control valve (5) to cylinder (6). Remove valve.
3. Cut seal wire (7). Remove wire and seal (8). Discard wire and seal.
4. Pull handle (9) and remove insert (10) from handle.
0527 00-2
TM 9-2350-247-20-3
5. Slide insert (1) down cable (2) until wedge (3) can be seen. Remove wedge and insert from cable.
6. Remove screw (4), lock washer (5), and clamp (6) securing tube (7) to bulkhead. Discard lock washer. Remove tube.
7. Loosen nut (8) from tube reducer (9).
8. Loosen jam nut (10) and nut (11) that secure tube reducer (9) to bulkhead. Remove tube reducer.
9. Remove screw (12) and lock nut (13) from bulkhead. Discard lock nut.
0527 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Install screw (12) in bulkhead. Secure with new lock nut (13).
2. Install tube reducer (9) through bulkhead. Secure with nut (11) and jam nut (10).
3. Route cable (2) through nut (8), tube (7), and tube reducer (9).
4. Install nut (8) on tube reducer (9) and tighten.
5. Slide insert (1) on cable (2). Bend cable over wedge (3). Install wedge and cable in insert.
6. Install insert (1) in handle (14).
0527 00-4
TM 9-2350-247-20-3
WARNING
Steel wire cannot be broken in an emergency. Make sure wire is light copper. Failure of fire
extinguisher to operate properly may cause injury to personnel or damage equipment.
NOTE
.020 copper safety wire is used to secure outside handle.
7. Install new copper wire seal (1) through screw (2) and handle (3). Make sure wire is tight so it will break when handle is
pulled. Crimp seal (4) on wire.
8. Install adapter (5) on control valve (6).
10. Install tube (9) on adapter (5).
11. Tighten nut (10) to secure tube (9) on adapter (5).
12. Install clamp (11), new lock washer (12), and screw (13) securing tube (9) to bulkhead.
0527 00-5
TM 9-2350-247-20-3
END OF TASK
0527 00-6
TM 9-2350-247-20-3
REPLACE WALTER KIDDE CONTROL VALVE 0528 00

INITIAL SETUP:

Unit See your -10
Materials/Parts
Lock nut
Wire seal (.020 copper) Driver’s seat raised (see your -10)
0528 00-1
TM 9-2350-247-20-3
REPLACE WALTER KIDDE CONTROL VALVE — Continued 0528 00
REMOVAL
1. Loosen nut (1) that secures tube (2) to adapter (3).
2. Remove adapter (3) from control valve (4).
3. Loosen nut (5) that secures control valve (4) to cylinder (6). Remove valve.
4. Cut seal wire (7). Remove wire and seal (8). Discard wire and seal.
5. Pull handle (9) and remove insert (10) from handle.
6. Slide insert (10) down cable (11) until wedge (12) can be seen. Remove wedge and insert from cable.
0528 00-2
TM 9-2350-247-20-3
7. Remove screw (1), lock washer (2), and clamp (3) securing tube (4) to bulkhead. Discard lock washer.
8. Loosen nut (5) that secures tube (4) to tube reducer (6). Remove tube.
9. Loosen jam nut (7) and nut (8) that secure tube reducer (6) to bulkhead. Remove tube reducer.
10. Remove screw (9) and lock nut (10) from bulkhead. Discard lock nut.
0528 00-3
TM 9-2350-247-20-3
INSTALLATION
1. Install screw (9) in bulkhead. Secure with new lock nut (10).
2. Install tube reducer (6) through bulkhead. Secure with nut (8) and jam nut (7).
3. Route cable (11) through tube (4), nut (5), and tube reducer (6).
4. Secure cable (11) to tube reducer (6) with nut (5).
5. Slide insert (12) on cable (11). Bend cable over wedge (13) and install wedge and cable in insert.
6. Install insert (12) in handle (14).
0528 00-4
TM 9-2350-247-20-3
WARNING
Steel wire cannot be broken in an emergency. Make sure the wire is light copper. Failure of fire
extinguisher to operate properly may cause injury to personnel or damage equipment.
NOTE
.020 copper safety wire is used to secure outside handle.
7. Install new copper wire seal (1) through screw (2) and handle (3). Make sure wire is tight so it will break when handle is
pulled. Crimp seal (4) on wire.
8. Install adapter (5) in control valve (6).
10. Install tube (9) on adapter (5). Secure with nut (10).
0528 00-5
TM 9-2350-247-20-3
11. Install clamp (11), new lock washer (12), and screw (13) securing tube (9) to bulkhead.
END OF TASK
0528 00-6
TM 9-2350-247-20-3
REPLACE/REPAIR PORTABLE FIRE EXTINGUISHER PANEL ASSEMBLY 0529 00

(M548A3)
INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
Materials/Parts
Equipment Condition
Decal
Rubber bumper (4) Carrier blocked (see your -10)
0529 00-1
TM 9-2350-247-20-3
REPLACE/REPAIR PORTABLE FIRE EXTINGUISHER PANEL ASSEMBLY (M548A3) — 0529 00

Continued
REMOVAL
WARNING
Portable and fixed fire extinguisher cylinders are under pressure and can discharge and injure
you. Handle cylinders with care.
1. Remove web strap (1) and portable fire extinguisher (2) from panel assembly (3).
2. Remove 10 screws (4), washers (5), and lock washers (6) securing panel assembly (3) to carrier. Discard lock washers.
3. Remove panel assembly (3) from carrier.
0529 00-2
TM 9-2350-247-20-3

Continued
DISASSEMBLY
1. Remove four rubber bumpers (7) from four brackets (8) on panel assembly (3). Discard rubber bumpers.
2. Inspect decal (9) on panel assembly (3). Replace decal if necessary.
ASSEMBLY
1. Clean mounting surface of new decal (1) if replaced. Use cleaning compound.
2. Install four new rubber bumpers (2) in four brackets (3) on panel assembly (4).
0529 00-3
TM 9-2350-247-20-3

Continued
INSTALLATION
1. Install panel assembly (4) in carrier. Secure panel to carrier with 10 new lock washers (5), washers (6), and screws (7).
2. Secure portable fire extinguisher (8) on panel assembly (4) with web strap (9).
END OF TASK
0529 00-4
TM 9-2350-247-20-3
CHAPTER 25
FOR NBC SYSTEM (M548A3)
WORK PACKAGE INDEX

Title Sequence No.
REPLACE NBC CIRCUIT BREAKER AND RELAY (M548A3)...................................................................................0530 00
REPLACE NBC WIRING HARNESS FROM BATTERY COMPARTMENT TO MANIFOLD
(M548A3).................................................................................................................................................................0531 00
REPLACE NBC M3 HEATER AND ADAPTER (M548A3)...........................................................................................0532 00
REPAIR NBC MANIFOLD (M548A3).............................................................................................................................0533 00
REMOVE/INSTALL NBC M1A1-19 PRECLEANER ASSEMBLY AND FRAME (M548A3).....................................0534 00
REPLACE NBC M19 PARTICULATE FILTER UNIT (M548A3)..................................................................................0535 00
REPLACE NBC M18 FILTER (M548A3)........................................................................................................................0536 00
REPLACE NBC FILTERED AIR HOSE (M548A3)........................................................................................................0537 00
REPLACE NBC ORIFICE CONNECTOR ASSEMBLY AND BRACKET (M548A3)..................................................0538 00
TM 9-2350-247-20-3
REPLACE NBC CIRCUIT BREAKER AND RELAY (M548A3) 0530 00

Test and Inspection (page 0530 00-2).
INITIAL SETUP:

Unit See your -10
Multimeter (WP 0541 00, Item 29)
Personnel Required Driver’s seat raised (see your -10)
Unit Mechanic Both battery negative leads disconnected (WP 0292 00)
REMOVAL
NOTE
Mark all parts for easy identification before removing.
1. Remove nut (1), lock washer (2), circuit 135G lead (3), and washer (4) from relay terminal A2 (5).
2. Remove nut (6), lock washer (7), circuit 537 lead (8), and washer (9) from relay terminal X1 (10).
3. Remove nut (11), lock washer (12), one end of jumper (13), and washer (14) from relay terminal A1 (15).
4. Remove nut (16), lock washer (17), ground lead (18), and washer (19) from relay terminal X2 (20).
5. Remove screw (21), jumper (13), and washer (22) from circuit breaker (23).
0530 00-1
TM 9-2350-247-20-3
REPLACE NBC CIRCUIT BREAKER AND RELAY (M548A3) — Continued 0530 00
6. Remove screw (24), lock washer (25), one end of jumper (26), and washer (27) from circuit breaker (23).
7. Remove nut (28), washer (29), jumper (26), and screw (30) from bus bar (31).
8. Remove two nuts (32), lock washers (33), washers (34), screws (35), ground lead (18), and relay (36). Discard lock washers.
9. Remove two nuts (37), screws (38), and circuit breaker (23) from panel.
TEST AND INSPECTION

1. Check resistance through circuit breaker. Reading should be 0 ohms. If reading is infinity, replace defective circuit
breaker.
2. Check resistance through relay. Place multimeter probes on terminals X1 and X2. Reading should be approximately 0
ohms. If reading is infinity, replace relay. Place multimeter probes on terminals A1 and A2. Reading should be infinity.
If reading is 0 ohms, replace relay.
0530 00-2
TM 9-2350-247-20-3
REPLACE NBC CIRCUIT BREAKER AND RELAY (M548A3) — Continued 0530 00
INSTALLATION
1. Install circuit breaker (1) with two screws (2) and nuts (3).
2. Install relay (4) and one end of ground lead (5) on panel with two screws (6), washers (7), new lock washers (8), and
nuts (9).
3. Install one end of jumper (10) on bus bar (11) with screw (12), washer (13), and nut (14).
4. Install washer (15), jumper (10), washer (16), and screw (17) on circuit breaker (1).
5. Install washer (18), one end of jumper (19), and screw (20) on circuit breaker (1).
6. Install washer (21), ground lead (5), washer (22), and nut (23) on relay terminal X2 (24).
7. Install washer (25), jumper (19), washer (26), and nut (27) on relay terminal A1 (28).
8. Install washer (29), circuit 537 lead (30), washer (31), and nut (32) on relay terminal X1 (33).
9. Install washer (34), circuit 135G lead (35), washer (36), and nut (37) on relay terminal A2 (38).
END OF TASK
0530 00-3/4 blank

TM 9-2350-247-20-3
REPLACE NBC WIRING HARNESS FROM BATTERY COMPARTMENT TO 0531 00

MANIFOLD (M548A3)
INITIAL SETUP:

General Mechanic’s Tool Kit (WP 0541 00, Item 57) Both battery negative leads disconnected (WP 0292 00)
Materials/Parts Driver’s side front left battery removed (WP 0293 00)
Lock washer (5) NBC manifold removed (WP 0533 00)
Personnel Required M1A1-19 Precleaner assembly and frame removed
(WP 0534 00)
Unit Mechanic
Driver’s left side floor plate removed (WP 0395 00)
References Steering guard removed (WP 0365 00)
See your -10 Instrument panel partially removed (WP 0256 00)
0531 00-1
TM 9-2350-247-20-3
REPLACE NBC WIRING HARNESS FROM BATTERY COMPARTMENT TO MANIFOLD 0531 00

REMOVAL
NOTE
Mark all parts for easy identification before removing.
1. Disconnect circuit 400D lead (1) from lead (2) on vehicle compartment heater control box (3).
2. Disconnect circuit 400C lead (4) from circuit 400 lead (5).
3. Disconnect circuit 400A lead (6) from circuit 400 lead (7) on coolant heater control box (8), if installed.
4. Disconnect NBC wiring harness (9) at connector (10) to M3 heater harness connector (11).
5. Remove three clamps (12), screws (13), and lock washers (14) securing NBC wiring harness (9) and existing harness to
weld nuts behind instrument panel (15). Discard lock washers.
6. Remove NBC wiring harness (9) with grommets (16) from stiffener (17) and stiffener (18).
0531 00-2
TM 9-2350-247-20-3

7. Disconnect 135H lead (1) from terminal (2) on air filter indicator (3) on back side of instrument panel (4).
8. Disconnect circuit 537 lead (5) from bottom terminal (6) on air filter switch (7) on back side of instrument panel (4).
9. Disconnect circuit 400B lead (8) from top terminal (9) on air filter switch (7) on back side of instrument panel (4).
10. Remove two clamps (10), screws (11), lock washers (12), and NBC wiring harness (13) and existing harness from weld
nuts on inside of driver’s left side floor plate. Discard lock washers.
11. Remove nut (14), lock washer (15), circuit 135G lead (16), and washer (17) from relay terminal A2 (18).
12. Remove nut (19), lock washer (20), circuit 537 lead (21), and washer (22) from relay terminal X1 (23).
13. Remove NBC wiring harness (13) with grommet (24) from battery compartment.
14. Remove NBC wiring harness (13) from carrier.
0531 00-3
TM 9-2350-247-20-3

INSTALLATION
NOTE
Hardware is supplied with new relay and circuit breaker only and can not be ordered through
TM 9-2350-247-24P.
1. Place grommet (24) on NBC wiring harness (13) and route harness through hole in battery box compartment.
2. Route NBC wiring harness (13) under driver’s left side floor plate and up behind instrument panel (4).
3. Place two grommets (25) on NBC wiring harness (13) and route harness through holes in stiffener (26) and stiffener (27).
Make sure grommets are securely in holes to avoid damaging the harness from metal contact and vibration.
4. Connect NBC wiring harness connector (28) to M3 heater wiring harness connector (29).
5. Install washer (22), circuit 537 lead (21), lock washer (18), and nut (17) on relay terminal X1 (23).
6. Install washer (17), circuit 135G lead (16), lock washer (15), and nut (14) on relay terminal A2 (18).
7. Install two clamps (10) on existing harness and NBC wiring harness (13). Secure clamps on weld nuts under driver’s left
side floor plate with two screws (11) and new lock washers (12).
0531 00-4
TM 9-2350-247-20-3

8. Install three clamps (1) on existing harness and NBC wiring harness (2) behind instrument panel (3). Secure clamps on
weld nuts with three screws (4) and new lock washers (5).
9. Connect circuit 135H lead (6) to terminal (7) on air filter indicator (8) on back side of instrument panel (3).
10. Connect circuit 537 lead (9) to bottom terminal (10) on air filter switch (11) on back side of instrument panel (3).
11. Connect circuit 400B lead (12) to top terminal (13) on air filter switch (11) on back side of instrument panel (3).
12. Connect circuit 400D lead (14) to lead (15) on vehicle compartment heater control box (16).
13. Connect circuit 400C lead (17) to circuit 400 lead (18).
14. If installed, connect circuit 400A lead (19) to circuit 400 lead (20) on coolant heater control box (21).
2. Install steering guard(WP 0365 00).
3. Install driver’s left side floor plate (WP 0395 00).
4. Install M1A1-19 precleaner assembly and frame (WP 0534 00).
6. Install driver’s side left front battery (WP 0293 00).
END OF TASK
0531 00-5/6 blank

TM 9-2350-247-20-3
REPLACE NBC M3 HEATER AND ADAPTER (M548A3) 0532 00

INITIAL SETUP:

Unit Unit Mechanic
References
See your -10
0532 00-1
TM 9-2350-247-20-3
REPLACE NBC M3 HEATER AND ADAPTER (M548A3) — Continued 0532 00
REMOVAL
WARNING
NBC agents can kill you. Do not service air cleaner or vent system after NBC attack until
carrier has been decontaminated and filters disposed of by NBC team. Unit commander or
officer in charge must assign NBC team to decontaminate system and dispose of filters. Unit
commander or officer in charge must prescribe necessary protective clothing and safety
measures for NBC team.
NOTE
All five M3 heaters and adapters are removed the same way. If your carrier was converted from
a M730A2, it may have five heaters, otherwise the M548A3 will have only four heaters.
1. Remove clamp (1) and hose (2) from outlet adapter (3).
2. Remove clamp (4) and hose (5) from inlet adapter (6).
3. Disconnect electrical lead (7) of wiring harness from M3 heater lead (8).
4. Remove four lock nuts (9), lock washers (10), screws (11), and M3 heater (12) from manifold (13). Discard lock nuts
and lock washers.
5. Remove inlet adapter (6) and outlet adapter (3) from M3 heater (12).
0532 00-2
TM 9-2350-247-20-3
REPLACE NBC M3 HEATER AND ADAPTER (M548A3) — Continued 0532 00
INSTALLATION
NOTE
All five M3 heaters and adapters are installed the same way. If your carrier was converted from
a M730A2, it may have five heaters, otherwise the M548A3 will have only four heaters.
1. Install inlet adapter (1) and outlet adapter (2) on M3 heater (3).
2. Install hose (4) on inlet adapter (1). Secure with clamp (5).
3. Install M3 heater (3) on manifold (6). Secure with four screws (7), new lock washers (8), and new lock nuts (9).
4. Connect electrical lead (10) of wiring harness to M3 heater lead (11).
5. Install hose (12) on outlet adapter (2). Secure with clamp (13).
END OF TASK
0532 00-3/4 blank

TM 9-2350-247-20-3
REPAIR NBC MANIFOLD (M548A3) 0533 00

Inspection (page 0533 00-4).
INITIAL SETUP:

Unit Unit Mechanic
Helper (H)
Materials/Parts See your -10
Cotter pin (8) Equipment Condition
Lock nut (20)
Lock washer (20) Both battery negative leads disconnected (WP 0292 00)
Portable fire extinguisher removed (see your -10)
0533 00-1
TM 9-2350-247-20-3
REPAIR NBC MANIFOLD (M548A3) — Continued 0533 00
REMOVAL
WARNING
NOTE
Remove oil can before removing manifold (see your -10).
NOTE
Only M548A3 carriers converted from M730A2 will have five NBC stations.
1. Remove clamp (1) and clamp (2) securing hose (3) and hose (4) to outlets on M1A1-19 precleaner (5).
2. Disconnect five quick disconnect couplings (6) from five orifice connector assemblies (7).
3. Disconnect circuit 135 lead (8) from main NBC wiring harness.
4. Remove two screws (9) and lock washers (10) securing manifold (11) to mounting brackets (12). Remove manifold from
carrier. Have helper assist. Discard lock washers.
0533 00-2
TM 9-2350-247-20-3
DISASSEMBLY
1. Remove two nuts (1), lock washers (2), screws (3) and clamps (4) securing NBC wiring harness (5) to two short heater
mounts (6) on manifold (7). Discard lock washers.
NOTE
Perform Step 2 if manifold is being replaced.
2. Disconnect NBC wiring harness (5) leads from five M3 heaters (8).
3. Remove four grommets (9) and NBC wiring harness (5) from two long heater mounts (10) on manifold (7).
4. Loosen clamp (11) and clamp (12) securing hose (13) and hose (14) to manifold (7). Remove hoses from manifold.
5. Remove four nuts (15) and disconnect four clamps (16) securing M18 filter (17) and M18 filter (18) to manifold (7).
Remove filters and attached hoses from manifold.
0533 00-3
TM 9-2350-247-20-3
6. Remove eight cotter pins (19), headed pins (20), four clamps (16), and eight bumpers (21) from manifold (7). Discard
cotter pins.
7. Loosen five clamps (22) securing five hoses (23) to manifold (7).
8. Remove 20 lock nuts (24), lock washers (25), and screws (26) securing 5 M3 heaters (8) to manifold (7). Discard lock
washers and lock nuts.
9. Remove five hoses (23) from outlets on manifold (7) and five M3 heaters (8) from manifold.
INSPECTION
NOTE
Do not use any solvents inside the manifold.
1. Inspect manifold for breaks, cracks, and signs of leaks. Replace manifold if there is any damage that will let it leak.
Clean the manifold with a clean, dampened, lint free cloth.
0533 00-4
TM 9-2350-247-20-3
ASSEMBLY
1. Install five hoses (1) connected to five M3 heaters (2) on outlets of manifold (3).
2. Secure 5 M3 heaters (2) to manifold (3) with 20 screws (4), new lock washers (5), and new lock nuts (6).
3. Secure five hoses (1) to outlets on manifold (3) with five clamps (7).
4. Install eight bumpers (8), four clamps (9), eight headed pins (10), and eight new cotter pins (11) on manifold (3).
5. Install M18 filter (12) and M18 filter (13) with attached hoses on manifold (3). Secure filters with four clamps (9) and
nuts (14).
6. Install two hoses (15 and 16) on outlets of manifold (3). Secure with clamp (17) and clamp (18).
7. Install four grommets (19) and NBC wiring harness (20) in two long heater mounts (21) on manifold (3) with NBC
wiring harness circuit 135 lead (22) on left end of manifold (3).
8. Secure NBC wiring harness (20) to two short heater mounts (23) on manifold (3) with two clamps (24), screws (25), new
lock washers (26), and nuts (27).
9. Connect NBC wiring harness (20) leads to five M3 heaters (2).
0533 00-5
TM 9-2350-247-20-3
INSTALLATION
1. Position manifold (11) in carrier. Have helper assist.
2. Connect circuit 135 lead (8) to main NBC wiring harness.
3. Install manifold (11) on mounting brackets (12) with two new lock washers (10) and screws (9).
4. Connect five quick disconnect couplings (6) to five orifice connector assemblies (7).
5. Install two hoses (4 and 3) on outlets of M1A1-19 precleaner (5) with clamp (2) and clamp (1).
1. Install portable fire extinguisher (see your -10).
2. Install oil can in mounting bracket (see your -10).
END OF TASK
0533 00-6
TM 9-2350-247-20-3
REMOVE/INSTALL NBC M1A1-19 PRECLEANER ASSEMBLY AND FRAME 0534 00

(M548A3)
INITIAL SETUP:

Unit See your -10

Equipment Condition
Materials/Parts
Lock washer (4) Both battery negative leads disconnected (WP 0292 00)
Personnel Required Portable fire extinguisher removed (see your -10)
Unit Mechanic NBC manifold removed (WP 0533 00)
0534 00-1
TM 9-2350-247-20-3
REMOVE/INSTALL NBC M1A1-19 PRECLEANER ASSEMBLY AND FRAME (M548A3) — 0534 00

Continued
REMOVAL
WARNING
NOTE
The M548A3 should only have four NBC stations. Converted M730A2 vehicles may have five
NBC stations.
1. Disconnect circuit 135F lead (1) from precleaner electrical socket (2).
2. Disconnect strap (3) securing precleaner assembly (4) to frame assembly (5). Remove precleaner assembly.
3. Remove four screws (6) and lock washers (7) securing frame assembly (5) to mounting strips (8). Remove frame
assembly from carrier. Discard lock washers.
0534 00-2
TM 9-2350-247-20-3
REMOVE/INSTALL NBC M1A1-19 PRECLEANER ASSEMBLY AND FRAME (M548A3) — 0534 00

Continued
INSTALLATION
1. Install frame assembly (1) on mounting strips (2) with four new lock washers (3) and screws (4).
2. Install precleaner assembly (5) on frame assembly (1) with strap (6).
3. Connect circuit 135F lead (7) to precleaner electrical socket (8). Tighten finger tight only.
END OF TASK
0534 00-3/4 blank

TM 9-2350-247-20-3
REPLACE NBC M19 PARTICULATE FILTER UNIT (M548A3) 0535 00

INITIAL SETUP:

Unit See your -10
Personnel Required
Unit Mechanic
Materials/Parts Both battery negative leads disconnected (WP 0292 00)
Lock washer (4) M1A1-19 precleaner assembly removed (WP 0534 00)
0535 00-1
TM 9-2350-247-20-3
REPLACE NBC M19 PARTICULATE FILTER UNIT (M548A3) — Continued 0535 00
REMOVAL
WARNING
1. Remove four screws (1) and lock washers (2) securing manifold (3) to precleaner housing (4). Discard lock washers.
2. Remove manifold (3) from precleaner housing (4).
3. Remove two air flow control caps (5) from two outlets (6) on manifold (3).
4. Remove M19 particulate filter (7) from precleaner housing (4). Tilt housing to facilitate removal of filter.
0535 00-2
TM 9-2350-247-20-3
REPLACE NBC M19 PARTICULATE FILTER UNIT (M548A3) — Continued 0535 00
INSTALLATION
1. Install M19 particulate filter (1) in precleaner housing (2). Make sure felt gasket on M19 particulate filter is facing the
manifold (3).
2. Install two air flow control caps (4) on two outlets (5) on manifold (3).
3. Install manifold (3) on precleaner housing (2). Secure with four screws (6) and new lock washers (7).
1. Install M1A1-19 precleaner (WP 0534 00).
END OF TASK
0535 00-3/4 blank

TM 9-2350-247-20-3
REPLACE NBC M18 FILTER (M548A3) 0536 00

INITIAL SETUP:

Unit See your -10

Unit Mechanic
Portable fire extinguisher removed (see your -10)
Helper (H)
NBC manifold removed (WP 0533 00)
REMOVAL
WARNING
NOTE
The M548A3 should only have four NBC stations. Converted M730A2 vehicles may have five
NBC stations.
1. Remove clamp (1), clamp (2), hose (3), and hose (4) from ends of M18 filter (5).
0536 00-1
TM 9-2350-247-20-3
REPLACE NBC M18 FILTER (M548A3) — Continued 0536 00
2. Remove clamp (6), clamp (7), hose (8), and hose (9) from ends of M18 filter (10).
3. Remove four nuts (11) and disconnect four clamps (12) securing M18 filter (5) and M18 filter (10) to manifold (13).
Remove filters from manifold.
INSPECTION
1. Inspect M18 filters for damage and exposure to water. Replace if there is any damage to filters or any water damage.
2. Inspect M18 filters for high resistance to air flow.
0536 00-2
TM 9-2350-247-20-3
REPLACE NBC M18 FILTER (M548A3) — Continued 0536 00
INSTALLATION
1. Install M18 filter (1) in two clamps (2) on manifold (3) with AIR FLOW arrow pointing toward hose (4) on right side of
M18 filter. Secure clamps with two nuts (5).
2. Install hose (4) and hose (6) on ends of M18 filter (1) with clamp (7) and clamp 8(8).
3. Install M18 filter (9) in two clamps (2) on manifold (3) with AIR FLOW arrow pointing toward hose (10) on left side of
M18 filter. Secure clamps with two nuts (5).
4. Install hose (10) and hose (11) on ends of M18 filter (9) with clamp (12) and clamp (13).
END OF TASK
0536 00-3/4 blank

TM 9-2350-247-20-3
REPLACE NBC FILTERED AIR HOSE (M548A3) 0537 00

INITIAL SETUP:

Unit See your -10
General Mechanics Tool Kit (WP 0541 00, Item 57) Equipment Condition
0537 00-1
TM 9-2350-247-20-3
REPLACE NBC FILTERED AIR HOSE (M548A3) — Continued 0537 00
REMOVAL
WARNING
NOTE
The removal, inspection, and installation procedures are the same for each NBC filtered air
hose.
NOTE
M548A3 carrier should only have four NBC stations. Converted M730A2 vehicles may have five
NBC stations.
1. Remove quick disconnect coupling (1) from orifice connector assembly (2).
2. Remove ratchet clamp (3) securing filtered air hose (4) to outlet adapter (5) on M3 heater (6). Push blade of screwdriver
under catch on ratchet clamp and lift up catch release. Remove hose from adapter.
3. Remove ratchet clamp (7) securing filtered air hose (4) to quick disconnect coupling (1). Push blade of screwdriver
under catch on ratchet clamp and lift up catch release. Remove hose from quick disconnect coupling.
0537 00-2
TM 9-2350-247-20-3
REPLACE NBC FILTERED AIR HOSE (M548A3) — Continued 0537 00
INSPECTION
1. Inspect quick disconnect coupling for wear, grooves, nicks, scratches, and loose fittings that may cause quick disconnect
coupling to leak. Replace quick disconnect coupling if leakage is suspected.
2. Inspect filtered air hose for cracks, wear, crimps, and breaks that could cause air leaks. Replace hose that shows signs of
leakage.
3. Inspect ratchet clamps for deformation and excessive wear. Replace clamps that show either of these defects.
INSTALLATION
1. Install ratchet clamp (1) on each end of filtered air hose (2).
2. Install filtered air hose (2) on outlet adapter (3) on M3 heater (4) and quick disconnect coupling (5).
3. Install quick disconnect coupling (5) on orifice connector assembly (6).
END OF TASK
0537 00-3/4 blank

TM 9-2350-247-20-3
REPLACE NBC ORIFICE CONNECTOR ASSEMBLY AND BRACKET 0538 00

(M548A3)
INITIAL SETUP:

Unit Unit Mechanic

Materials/Parts
Equipment Condition
Lock nut
Lock washer Engine stopped (see your -10)
0538 00-1
TM 9-2350-247-20-3
REPLACE NBC ORIFICE CONNECTOR ASSEMBLY AND BRACKET (M548A3) — 0538 00

Continued
REMOVAL
WARNING
NOTE
Procedures to remove, repair, and install orifice connectors and brackets are the same for all
five orifice connectors.
NOTE
Typically, the M548A3 carrier will only have four NBC stations. Converted M730A2 vehicles
have five NBC stations.
1. Locate five orifice connectors (1) in carrier.
0538 00-2
TM 9-2350-247-20-3

Continued
2. Remove quick disconnect coupling (2) from orifice connector assembly (3).
3. Remove retaining ring (1) securing orifice connector assembly (2) to bracket (3). Remove orifice connector assembly
from bracket.
4. Remove lock nut (4), lock washer (5), washer (6), and screw (7) securing bracket (3) to cowl stiffener. Discard lock nut
and lock washer.
5. Remove outlet valve cover (8) from orifice connector (9).
6. Remove outlet valve disk (10) from orifice connector (9).
INSPECTION
1. Inspect outlet valve cover for damage or wear. If damaged or worn, replace valve cover.
2. Inspect outlet valve disk for cracking, curling, deterioration, tears, and seating. If damaged, replace valve disk.
0538 00-3
TM 9-2350-247-20-3

Continued
INSTALLATION
1. Place bracket (3) on cowl stiffener and secure with screw (7), new lock washer (5), washer (6), and new lock nut (4).
2. Install outlet valve disk (10) on orifice connector (9).
3. Install outlet valve cover (8) on orifice connector (9).
4. Install orifice connector (9) in bracket (3) with retaining ring (1).
5. Install quick disconnect coupling (10) on orifice connector assembly (11).
END OF TASK
0538 00-4
TM 9-2350-247-20-3
CHAPTER 26
UNIT SUPPORTING INFORMATION
WORK PACKAGE INDEX

Title Sequence No.
REFERENCES...................................................................................................................................................................0539 00
MAINTENANCE ALLOCATION CHART (MAC).........................................................................................................0540 00
COMMON TOOLS AND SUPPLEMENTS AND SPECIAL TOOLS/FIXTURES LIST...............................................0541 00
EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST................................................................................0542 00
TM 9-2350-247-20-3
REFERENCES 0539 00
SCOPE
This work package lists all technical manuals, miscellaneous publications, and forms referenced in this manual.
TECHNICAL MANUALS
Destruction of Conventional Ammunition and Improved Conventional Munitions (ICM) to
Prevent Enemy Use.........................................................................................................................................TM 43–0002–33
Organizational Maintenance Repair Parts and Special Tools List: Welding Set, Arc, Inert-Gas
Shielded, Plastic or Metal-Lined Gun for 3/64-inch Wire; DC, 115 V (Westinghouse Model
SA-135) (FSN 3431-879-9709)................................................................................................................TM 5-3431-200-20P
Inspection, Care, and Maintenance of Antifriction Bearings..........................................................................................TM 9-214
Maintenance and Components Manual for Heater and Heater Control Box..............................................TM 9-2540-205-24&P
Organizational, Direct Support, and General Support Maintenance Manual (Including Parts
and Special Tools List) for Heater, Vehicular Compartment NSN 2540-01-396-2826;
Model A-20............................................................................................................................................TM 9-2540-207-14&P
Operator, Organizational, DS and GS Maintenance Manual for Lead-Acid Storage Batteries.......................TM 9-6140-200-14
Operator, Organizational, DS and GS Maintenance Manual; Standards for Inspection and
Classification of Tracks, Track Components, and Solid-Rubber Tires.......................................................TM 9-2530-200-24
Operator, Unit, and Direct Support Maintenance with Repair Parts List and Components
List for Mount, Machine Gun, MK64 used with Machine Gun, MK 19 MOD 3, 40MM;
Machine Gun, M2, Caliber .50; Machine Gun, M60, 7.62MM; Machine Gun, M60E3,
7.62MM..................................................................................................................................................TM 9-1010-231-13&P
Operator, Organizational, DS, GS, and Depot Maintenance Manual: Welding Set, Arc,
Inert-Gas Shielded; Plastic or Metal-Lined Gun; for 3/64-inch Wire; DC, 115 V
(Westinghouse Model SA-135) (FSN 3431-879-9709)..............................................................................TM 5-3431-200-15
Operator’s and Organizational Maintenance Manual Including Repair Parts and Special
Tools List for Simplified Test Equipment for Internal Combustion Engines (NSN
4910-01-124-2554).................................................................................................................................TM 9-4910-571-12&P
Operator’s Manual; Radio Sets; AN/VRC-12, AN/VRC-43, AN/VRC-44, AN/VRC-45,
AN/VRC-46, AN/VRC-47, AN/VRC-48, AN/VRC-49 .................................................................TM 11-5820-401-10-1, -2
Operator’s and Unit Maintenance Manual Including Repair Parts and Special Tools List
for Decontaminating Apparatus: Portable, 14 Liter, M13 (4230-01-133-4124) and
Decontaminating Apparatus: Portable, 14 Liter, M13 (Practice) (4230-01-345-5172).........................TM 3-4230-214-12&P
Operator’s Manual; Carrier, Cargo, Tracked, 6-ton; M548A1 (2350-01-096-9356), M548A3
(2350-01-369-6081)....................................................................................................................................TM 9-2350-247-10
Operator’s Manual for Tester, Airflow, Gas-Particulate Filter Unit, M39 (NSN
6680-00-436-4212)......................................................................................................................................TM 3-6680-316-10
Operator’s, Organizational, Direct Support, and General Support Maintenance Manual;
Suppressor, Electrical Transient, MX-7778A/GRC..................................................................................TM 11-5915-223-12
0539 00-1
Change 1
TM 9-2350-247-20-3
REFERENCES — Continued 0539 00
Operator’s, Unit, and Direct Support Maintenance Manual with Repair Parts and Special
Tools List (RPSTL) for Machine Gun Mounts and Combinations for Tactical/Armored
Vehicles and Ground Mounting M122 Machine Gun Tripod Mount; M122A1 Machine Gun
Mount; M3 Tripod Mount; M66 Machine Gun Mount Ring; M240E1 Flexible Machine
Gun Mount; M142 Machine Gun Mount; .50 Cal Machine Gun Mount; M548 Machine
Gun Mount; MK93 Mod 0 Machine Gun Mount (USMC Only); MK 93 Mod 1 Machine
Gun Mount; M6 Machine Gun Pedestal Mount; M197 Machine Gun Mount.......................................TM 9-1005-245-13&P
Organizational, Direct Support, and General Support Maintenance Manual (Including
Repair Parts and Special Tools) for Heaters, Vehicular Compartment: Stewart-Warner
10560M (NSN 2540-01-071-0651), 10560M24B1 (2540-01-169-5159),
10560C24 (2540-01-083-0691), and 10560G (7540-01-262-6013); Hupp MF560A
(2540-00-930-8938), MF510B (2540-01-071-0652), and MF510C, MF60B-24V
(2540-01-162-3834), ESPAR VZS (2540-01-114-7688).......................................................................TM 9-2540-205-24&P
Organizational, Direct Support and General Support Maintenance Manual: Machine Gun,
7.62, M60...............................................................................................................................................TM 9-1005-224-23&P
Unit and Direct Support Maintenance Manual, Including Repair Parts and Special Tools Lists
for Machine Guns, .50 Caliber, M2 Heavy Barrel, Flexible..................................................................TM 9-1005-213-23&P
Organizational Maintenance Manual; Radio Sets; AN/VRC-12, AN/VRC-43, AN/VRC-44,
AN/VRC-45, AN/VRC-46, AN/VRC-47, AN/VRC-48, AN/VRC-49 ...........................................TM 11-5820-401-20-1, -2
Painting Instructions for Army Material.....................................................................................................................TM 43-0139
Procedures for Destruction of Electronics Materiel to Prevent Enemy Use (Electronics
Command)..........................................................................................................................................................TM 750-244-2
Procedures for Destruction of Equipment in Federal Supply Classifications 1000, 1005, 1010,
1015, 1020, 1025, 1030, 1055, 1090, and 1095 to Prevent Enemy Use............................................................TM 750-244-7
Procedures for Destruction of Tank-Automotive Equipment to Prevent Enemy Use (U.S.
Army Tank-Automotive Command)..................................................................................................................TM 750-244-6
Unit Maintenance, Direct Support, and General Support Maintenance Repair Parts and Special
Tools List (Including Depot Maintenance Repair Parts and Special Tools List): for Carrier,
Cargo, Tracked, 6-ton; M548A1 (2350-01-096-9356); Carrier, Cargo, Tracked, 6-ton;
M548A3 (2350-01-369-6081)...................................................................................................................TM 9-2350-247-24P
Unit Maintenance Manual: Carrier, Cargo, Tracked, 6-ton, M548A1 (2350-01-096-9356),
M548A3 (2350-01-369-6081).......................................................................................................TM 9-2350-247-20-1, -2, -3
Unit Maintenance Repair Parts and Special Tool Lists: Welding Set, Arc, Inert Gas Shielded:
Plastic or Metal-Lined Gun; for 3/64-inch Wire; DC, 115 V (Westinghouse Model SA-135)
FSN 3431-879-9709..................................................................................................................................TM 5-3431-200-20P
Use and Care of Hand Tools and Measuring Tools.........................................................................................................TM 9-243
MISCELLANEOUS PUBLICATIONS
Accident Reporting and Records..................................................................................................................................AR 385-40
Aeronautical Equipment Army Oil Analysis Program (AOAP).................................................................................TB 43-0106
Army Maintenance Management System (TAMMS).........................................................................................DA Pam 738-750
Army Oil Analysis Program (AOAP) Guide for Leaders and Users .........................................................................TB 43-0211
Basic Cold Weather Manual............................................................................................................................................FM 31-70
0539 00-2
Change 1
TM 9-2350-247-20-3
REFERENCES — Continued 0539 00
CARC Spot Painting...................................................................................................................................................TB 43-0242

Color, Marking, and Camouflage-Painting of Military Vehicles, Construction Equipment, and
Materials-Handling Equipment..............................................................................................................................TB 43-0209
Consolidated Index of Army Publications and Blank Forms.................................................................................DA Pam 25-30
Desert Operations .............................................................................................................................................................FM 90-3
Expendable Items (except Medical, Class V, Repair Parts, and Heraldic Items)........................................................CTA 50-970
Explosives and Demolitions............................................................................................................................................FM 5-250
First Aid for Soldiers....................................................................................................................................................FM 4-25.11
General Fabric Repair.....................................................................................................................................................FM 10-16
Malfunctions Involving Ammunition and Explosives......................................................................................................AR 75-1
Operation and Maintenance of Ordnance Materiel in Cold Weather (0 F to -65 F)......................................................FM 9-207
Operator’s Manual: Welding Theory and Application...................................................................................................TC 9-237
Packing of Material for Packing...................................................................................................................................FM 38-701
Recovery and Battle Damage Assessment and Repair.................................................................................................FM 9-43-2
Rigging Techniques, Procedures, and Applications........................................................................................................FM 5-125
Safety Inspection and Testing of Lifting Devices.......................................................................................................TB 43-0142
Use of Antifreeze Solutions, Antifreeze Extender, Cleaning Compounds, and Test Kit in
Engine Cooling Systems........................................................................................................................................TB 750-651
Vehicle and Battlefield Damage Assessment and Repair.............................................................................................FM 9-43-2
Welding Code..................................................................................................................................................................12472301
FORMS
Refer to Department of the Army Pamphlet 310-1 for index of blank forms and to DA Pam 738-750 for explanation of use.
Oil Analysis Log...............................................................................................................................................DA Form 2408-20
Equipment Control Record.................................................................................................................................DA Form 2408-9
Equipment Inspection and Maintenance Worksheet..............................................................................................DA Form 2404
Exchange Tag.........................................................................................................................................................DA Form 2402
Maintenance Request.............................................................................................................................................DA Form 2407
Preventive Maintenance Schedule and Record........................................................................................................DD Form 314
Processing and Deprocessing Record for Shipment, Storage, and Issue of Vehicles and Spare
Engines..............................................................................................................................................................DD Form 1397
Product Quality Deficiencies Report (NSN 7540-00-133-5541)...............................................................................SF Form 368
Recommended Changes to Publications and Blank Forms...................................................................................DA Form 2028
Report of Discrepancy (ROD)...................................................................................................................................SF Form 364
Uncorrected Fault Record.................................................................................................................................DA Form 2408-14
0539 00-3/4 blank

Change 1
TM 9-2350-247-20-3
MAINTENANCE ALLOCATION CHART (MAC) 0540 00
INTRODUCTION
GENERAL
This section provides a general explanation of all maintenance and repair functions authorized at various maintenance levels.
The Maintenance Allocation Chart (MAC) (immediately following this introduction) designates overall authority and
responsibility for the performance of maintenance functions on the identified end item or component. The application of the
maintenance functions to the end item or component will be consistent with the capacities and capabilities of the designated
maintenance levels. They are:
Unit – includes two subcolumns, C (operator/crew) and O (unit) maintenance.
Direct Support – includes an F subcolumn.
General Support – includes an H subcolumn.
Depot – includes a D subcolumn.
The tools and test equipment requirements (immediately following the MAC) list the tools and test equipment (both special
tools and common tool sets) required for each maintenance function as referenced from the MAC.
The remarks (immediately following the tools and test equipment requirements) contain supplemental instructions and
explanatory notes for a particular maintenance function.
MAINTENANCE FUNCTIONS
Maintenance functions are limited to and defined as follows:
(1) Inspect. To determine the serviceability of an item by comparing its physical, mechanical, and/or electrical
characteristics with established standards through examination (e.g., by sight, sound, or feel).
(2) Test. To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical characteristics of an
item and comparing those characteristics with prescribed standards on a scheduled basis, i.e., load testing of lift
devices and hydrostatic testing of pressure hoses.
(3) Service. Operations required periodically to keep an item in proper operating condition, i.e., to clean (includes
decontaminate, when required), to preserve, to drain, to paint, or to replenish fuel, lubricants, chemical fluids, or
gasses. This includes scheduled exercising and purging of recoil mechanisms.
(4) Adjust. To maintain or regulate, within prescribed limits, by bringing into proper or exact position, or by setting the
operating characteristics to specified parameters.
(5) Align. To adjust specified variable elements of an item to bring about optimum or desired performance.
(6) Calibrate. To determine and cause corrections to be made or to be adjusted on instruments of test, measuring, and
diagnostic equipment used in precision measurement. Consists of comparisons of two instruments, one of which is a
certified standard of known accuracy, to detect and adjust any discrepancy in the accuracy of the instrument being
compared.
(7) Remove/Install. To remove and install the same item when required to perform service or other maintenance
functions. Install may be the act of emplacing, seating, or fixing into position a spare, repair part, or module
(component or assembly) in a manner to allow the proper functioning of an equipment or system.
(8) Replace. To remove an unserviceable item and install a serviceable counterpart in its place. “Replace” is authorized
by the MAC and is shown as the third position code of the Source, Maintenance and Recoverability (SMR) code.
(9) Repair. The application of maintenance services, including fault location/troubleshooting, removal/installation, and
disassembly/assembly procedures, and maintenance actions to identify troubles and restore serviceability to an item
by correcting specific damage, fault, malfunction, or failure in a part, subassembly, module (component or
assembly), end item, or system.
0540 00-1 Change 1

TM 9-2350-247-20-3
MAINTENANCE ALLOCATION CHART (MAC)—Continued 0540 00
NOTE
The following definitions are applicable to the “repair” maintenance function:
• Services – Inspect, test, service, adjust, align, calibrate, and/or replace.
• Fault location/troubleshooting – The process of investigating and detecting the cause of
equipment malfunctioning; the act of isolating a fault within a system or Unit Under Test
(ET).
• Disassembly/assembly – The step-by-step breakdown (taking apart) of a spare/functional
group coded item to the level of its least component that is assigned an SMR code for the
level of maintenance under consideration (i.e., identified as maintenance significant).
• Actions – Welding, grinding, riveting, straightening, facing, maching, and/or surfacing.
(10) Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completely
serviceable/operational condition as required by maintenance standards in appropriate technical publications.
Overhaul is normally the highest degree of maintenance performed by the Army. Overhaul does not normally
return an item to like-new condition.
(11) Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to a like-new
condition in accordance with original manufacturing standards. Rebuild is the highest degree of materiel
maintenance applied to Army equipment. The rebuild operation includes the act of returning to zero those age
measurements (e.g., hours/miles) considered in classifying Army equipment/components.
Explanation of Columns in the MAC
Column (1) – Group Number. Column (1) lists FGC numbers, the purpose of which is to identify maintenance significant
components, assemblies, subassemblies, and modules with the Next Higher Assembly (NHA).
Column (2) – Component/Assembly. Column (2) contains the names of components, assemblies, subassemblies, and modules
for which maintenance is authorized.
Column (3) – Maintenance Function. Column (3) lists the functions to be performed on the item listed in column (2). (For
detailed explanation of these functions refer to “Maintenance Functions” outlined above.)
Column (4) – Maintenance Level. Column (4) specifies each level of maintenance authorized to perform each function listed
in column (3) by indicating work time required (expressed as man-hours in whole hours or decimals) in the appropriate
subcolumn. This work time figure represents the active time required to perform that maintenance function at the indicated
level of maintenance. If the number or complexity of the tasks within the listed maintenance function varies at different
maintenance levels, appropriate work time figures are shown for each level. The work time figure represents the average
time required to restore an item (assembly, subassembly, component, module, end item, or system) to a serviceable condition
under typical field operating conditions. This time includes preparation time (including any necessary disassembly/assembly
time), troubleshooting/fault location time, and quality assurance time in addition to the time required to perform the specific
tasks identified for the maintenance functions authorized in the MAC. The symbol designations for the various maintenance
levels are as follows
C — Operator or Crew Maintenance
O — Unit Maintenance
F — Direct Support Maintenance
H — General Support Maintenance
D — Depot Maintenance
Column (5) – Tools and Equipment Reference Code. Column (5) specifies, by code, those common tool sets (not individual
tools) common Test, Measurement and Diagnostic Equipment (TMDE), and special tools, special TMDE, and special support
equipment required to perform the designated function. Codes are keyed to the entries in the tools and test equipment table.
Change 1 0540 00-2

TM 9-2350-247-20-3
Column (6) – Remarks Code. When applicable, this column contains a letter code, in alphabetic order, that is keyed to the
remarks table entries.
EXPLANATION OF COLUMNS IN TOOL AND TEST EQUIPMENT REQUIREMENTS

Column (1) Tool or Test Equipment Reference Code. The tool or test equipment reference code correlates with a code used in
column (5) of the MAC.
Column (2) – The lowest level of maintenance authorized to use the tool or test equipment.
Column (3) – Nomenclature. Name or identification of the tool or test equipment.
Column (4) – National Stock Number (NSN). The NSN of the tool or test equipment.
Column (5) – Tool Number. The manufacturer's part number, model number, or type number.
EXPLANATION OF COLUMNS IN REMARKS

Column (1) – Remarks Code. The code recorded in column (6) of the MAC.
Column (2) – Remarks. This column lists information pertinent to the maintenance function being performed as indicated in
the MAC.
0540 00-3 Change 1

TM 9-2350-247-20-3
Table 1. MAINTENANCE ALLOCATION CHART, SECTION II
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
DIRECT GENERAL TOOLS AND
GROUP COMPONENT/ MAINTENANCE UNIT SUPPORT SUPPORT DEPOT EQUIPMENT REMARKS
NUMBER ASSEMBLY FUNCTION CODE
C O F H D REF CODE
01 ENGINE
0100 POWER PLANT Remove/Install 2.5 1 A
Remove/Install 3.0
0100 POWER PLANT ASSY Adjust .2 96 98 105 A
(M548A3)
Remove/Install 3.7 95 97 98 99
102 104
Repair 1.3 .5 94 95 97 98
99 101 102
104 106 107
108
0101 ENGINE (M548A1) Test .1 234567
Service .2
Replace 9.5 1
Repair * 8 9 10
Overhaul 50.0
0101 ENGINE (M548A3) Inspect .1
Service .3 98
Adjust .1
Remove/Install .5 95 96 97 98
99 102 104
Replace 1.2 6.5 98 102 103
104 108
Repair .3 98 106 107
Overhaul 50.0
03 FUEL SYSTEM
0301 INJECTOR, FUEL, Test .2 36 37
ENGINE
Replace .6 38
Repair .3 2.0 39 40 41 42
43 44 45
Change 1 0540 00-4

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
0301 LEVER, CONTROL, Adjust .3
FUEL INJECTOR
Replace 1.0 38
Overhaul .8 36 39 40 41
42 45
0302 PUMP, FUEL, ENGINE Test .5 47
Replace 1.5
Repair 2.0
LINES, FUEL, Replace 1.5 46
INJECTOR
0304 CLEANER, AIR, Service .3
ENGINE (M548A1)
Replace 1.0
Repair .2
0304 CLEANER, ENGINE, Service .3
AIR (M548A3)
Replace 1.0 Q
Repair .2
0304 ELEMENT, ENGINE Service .3
AIR (M548A3)
Replace .1
0304 INTAKE, AIR Replace .6
CLEANER
0304 DUCTING/HOSES Repair .4 Q
(M548A3)
0305 BLOWER, AIR, ENGINE Replace 2.9
Repair 4.0
BLOWER ASSY, Replace 5.5
BYPASS (M548A3)
Overhaul 0.9 2.5 Z
0308 GOVERNOR (M548A1) Replace .5
Repair .2 2.0 B
0540 00-5 Change 1

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
0308 GOVERNOR ASSY Replace 1.0
(M548A3)
Repair 2.0 B, Z
0309 FILTER, FUEL, Service .1
PRIMARY (M548A1)
Replace .2
Repair .2
0309 FILTER, FUEL, Service .1
SECONDARY (M548A1)
Replace .2
Repair .2
0309 FILTER, PRIMARY Service .1
FUEL (M548A3)
Replace .6
Repair .2
0309 FILTER, SECONDARY Service .1
FUEL (M548A3)
Replace .6
Repair .2
0311 HEATER ASSEMBLY, Replace .5
AIR BOX
Repair 1.2
0312 SHAFT ASSEMBLY, Replace .5
CROSS
Repair 1.0 C
0312 BRACKET, ASSEMBLY, Replace .5
THROTTLE CONTROL
(M548A1)
Repair 1.5
0312 LINKAGE, THROTTLE Adjust .5
Replace .5
Repair 1.0
Change 1 0540 00-6

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
0312 THROTTLE PEDAL Adjust .3
CONTROLS AND
LINKAGE (M548A3)
Replace 1.4
0312 HAND THROTTLE Adjust .2
CONTROL
Replace .3
0312 FUEL CUTOFF Adjust .2
Replace .7
0312 TV MODULATOR ASSY Adjust .5
(M548A3)
Replace .5
05 COOLING SYSTEM
0501 RADIATOR (M548A1) Service .2 .5 50 X
Replace .7
Repair .1 4.0
0501 RADIATOR (M548A3) Service .2 .5 50 X
Repair 1.3
Replace .1 4.0
0504 PUMP, COOLANT Replace 1.2
Repair 1.8
0505 FAN, COOLING Service .1
(M548A1)
Replace .9
Repair 4.9
0505 FAN ASSEMBLY, Service .3 .3
VENTILATING
(M548A3)
Replace 2.2 T
Repair 4.9
0505 COOLING FAN ANGLE Replace 2.0
0505 DRIVE GEAR BOX Repair 2.0
ASSY (M548A3)
0540 00-7 Change 1

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
06 ELECTRICAL SYSTEM
0601 GENERATOR (M548A1) Replace .5 F
Repair 2.0
0601 GENERATOR ASSY Replace .5 U
(M548A3)
Repair 2.0 F
0602 REGULATOR, Adjust .1
GENERATOR (M548A1)
Replace .3
Repair 2.4
0603 STARTER (M548A1) Replace 6.1 Q
Repair 2.4 G
0603 ENGINE STARTER Replace .7 U
ASSY (M548A3)
Repair 2.4 G
0603 CABLES, STARTER Replace .3
CONNECTING
(M548A1)
Repair .2
0603 CABLES, STARTER Replace .3 U
(M548A3)
Repair .2
0607 PANEL, INSTRUMENT Replace .5 E
Repair 2.5
0607 WIRING HARNESS, Replace 2.0
INSTRUMENT PANEL
(M548A3)
Repair .4 E
0607 LIGHTS, INSTRUMENT Replace .2
PANEL (M548A1)
Repair .1
Change 1 0540 00-8

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
0607 CIRCUIT BREAKER Test .1 99
ASSEMBLY
Replace .6 99
Repair .4
0608 DISTRIBUTION BOX Replace .8
Repair 1.2
0609 LIGHTS, HULL DOME Replace .2
Repair .5
0609 HEADLIGHT, Replace .3
BLACKOUT
Repair .2
0609 STOPLIGHTS Replace .3
Repair .2
0609 LIGHT, BLACKOUT Replace .3 C
0609 MARKER Repair .2
0609 HEADLIGHT, SERVICE Replace .3
Repair .2
0613 WIRING HARNESS, Replace .4 C
POWER PLANT
(M548A1)
Repair .2
0613 WIRING HARNESS, Replace .8 D
POWER PLANT
(M548A3)
Repair .2
0613 WIRING HARNESS, Replace 3.5 C
INTERCONNECTING
(M548A1)
Repair .2
0614 RECEPTACLE, Replace .4 C
TRAILER COUPLING
Repair .6 C
0540 00-9 Change 1

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
07 TRANSMISSION
07 MOUNT, Replace .2 95 96 97 99 A
TRANSMISSION 102 104
(M548A3)
Repair .8 95 97 98 99 A
102 104
0705 LINKAGE, Adjust .3
TRANSMISSION
CONTROL
Replace .2
Repair .3
0705 SELECTOR, Adjust .3
TRANSMISSION
RANGE
Replace .5
Repair .7
0705 CONTROLLER, Replace 1.0 92 98 107
ELECTRICAL, TRANS,
(M548A3)
Repair .7 98 107
0708 TOW, START AND Adjust .2
CONTR (M548A3)
Repair .4 111
0710 TRANSMISSION Service .2
ASSEMBLY (M548A1)
Replace 8.7
Repair 16.0 51 52 53 54 H
55 56 57 58
59 60 61
Overhaul 25.0 U
Change 1 0540 00-10

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
0710 TRANSMISSION Service .4 .1 98 101
ASSEMBLY (M548A3)
Adjust .9 93 95 96 98
Replace 1.9 98 103 104
108
Repair 67.1 95 97 98 99 Y
101 102 104
107
Overhaul 50.0
0710 STEERING (M548A3) Adjust 1.0
08 TRANSFER GEARCASE
AND FINAL DRIVE
ASSEMBLIES
0801 TRANSFER GEARCASE Service .5
(M548A1)
Replace 11.0
Repair 6.2 70 I
0801 FINAL DRIVE Service .1 67
Replace 1.6 71
Repair 5.2 73 79 80 81
82
09 PROPELLER SHAFTS,
U-JOINTS AND
CLAMPS
0901 SPIDERS AND SHAFTS Service .2
Replace .6 76
11 DIFFERENTIAL
BAND, STEERING, Adjust .3
BRAKE DIFFERENTIAL
(M548A1)
Replace 1.1
Repair 1.6
0540 00-11 Change 1

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
1124 OIL FILTER, Service .2
DIFFERENTIAL
(M548A1)
Replace .9
Repair .3
1124 DIFFERENTIAL Service .1
CONTROL (M548A1)
Replace 2.6
Repair 16.0 72 78 79 80 I
81 82
12 BRAKE ASSEMBLY
1201 PARKING BRAKE Adjust .2
(M548A3)
Replace .6
1206 BRAKE INSTL Inspect .8 96 98 101
Adjust .4 96 98
Repair .8 96 98 116
1206 BRAKE LINKAGE Adjust .6
(M548A3)
Replace 2.2
13 WHEELS AND TRACKS
1301 SUPPORT ARM Service .2
ASSEMBLY, ROAD
WHEEL
Replace 2.0
1303 ADJUSTER, TRACK Adjust .2
TENSION
Replace .6
Repair 1.1
1303 ARM ASSEMBLY, Replace .7 L
IDLER WHEEL
Repair 1.0 C
Change 1 0540 00-12

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
1304 SPROCKET, DRIVE Inspect .2
Replace .5
1305 TRACK ASSEMBLY Adjust 0.2 84 85 89 90 I
SHOE, TRACK
Inspect 0.2 88 C
Replace 0.3
Repair 0.2
TRACK ASSEMBLY, Replace 1.4 S
T130
TRACK ASSEMBLY, Replace 1.5 S
T150
1311 ROAD WHEEL HUB Replace .8 87
BEARING
14 STEERING
14 STEERING WHEEL Service .2
ASSY (M548A3)
Adjust .9
Replace 2.2
1403 LINK ASSEMBLY Adjust .3
(M548A1)
1403 STEERING CONTROL Repair 2.0
(M548A1)
1403 BRAKE ASSEMBLY, Service .1
PIVOT (M548A1)
1403 STEER Replace .4
Adjust .6 93
1403 MASTER CYLINDER, Service .1
PIVOT STEER (M548A1)
Adjust .6
Replace .8
Repair 2.1 77
0540 00-13 Change 1

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
15 TOWING
ATTACHMENTS
1503 PINTLE, TOWING Service .1 C
Replace .2
Repair .4
16 SHOCK ABSORBER
1604 SHOCK ABSORBER Replace .4 94
Repair .5
18 HULL
1801 CAB CLOSURE Replace 1.2
ASSEMBLY
Repair 3.0 C
1802 WINDSHIELD Replace .2
Repair 1.0
1806 SEATS AND CUSHIONS Replace .3
Repair 1.5
1806 RACKS, BOXES AND Replace .3
STRAPS
Repair .4
20 WINCH AND POWER
TAKEOFF
2001 BAND, WINCH DRUM Adjust .1
(M548A1)
2001 BRAKE (M548A1) Replace .5
Repair .5
2001 CABLE, WINCH Service .2
(M548A1)
Replace .3
Repair .2
2001 CLUTCH, WINCH Adjust .1
(M548A1)
Change 1 0540 00-14

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
2001 DRUM (M548A1 Replace .9
Repair 1.3
2001 WINCH (M548A1) Service .1
Replace 1.0
Repair 3.0
2004 POWER TAKEOFF, Replace .9
WINCH (M548A1)
Repair 2.0
2004 SHAFT, PROPELLER, Service .1
FLANGE AND U-JOINT
Replace .3
Repair .1
2004 GEARCASE, WINCH Service .1
DRIVE (M548A1)
2004 TRANSFER GEARCASE Replace .4
Repair .9
22 HULL ACCESSORY
ITEMS
2201 COVER, CAB Remove/Install .3
Replace .5
Repair 1.0
2201 COVER, CARGO Remove/Install .5
Replace .6
Repair 1.5
2202 MOTOR, BLADE AND Adjust .1
ARM
2207 HEATER ASSY Replace 1.0
(M548A3)
Repair 1.2
0540 00-15 Change 1

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
26 ENGINE AND
TRANSMISSION
SLING, ENG AND Inspect .1 95 98
TRANS (M548A3)
Test .8 98
Repair .1 1.7 98 114 115
2604 STAND, ENG AND Service .1 108
TRANS (M548A3)
Adjust .2 98
Repair 1.3 98 108 114
115
33 SPECIAL PURPOSE
KITS
3301 SHIPPING Replace .2
CONTAINERS, ENGINE
KIT, VEHICLE
COMPARTMENT
HEATER (PRIMARY
AND SECONDARY
Repair 1.5
Remove/Install 4.0
3301 KIT, VEHICLE Remove/Install 4.0
COMPARTMENT
HEATER, (CARGO
PRIMARY AND
SECONDARY)
3301 KIT, ENGINE Remove/Install 4.0
COOLANT HEATER
3301 BOX, HEATER Replace .2
CONTROL
Repair .2
3301 FILTER, HEATER FUEL Replace .2
PUMP
Repair .3
Change 1 0540 00-16

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
3301 PUMP, HEATER FUEL Service .3
Replace .3
3301 HEATER, VEHICLE Replace .4
COMPARTMENT
Repair 1.6
3301 HEATER, COOLANT Replace .5
Repair 1.2
3301 IGNITER, COOLANT Replace .2
HEATER
3301 COVER, FIBERGLASS Replace .5
CAB
Repair 2.0
3301 COVER, INSULATED Replace .3
CARGO
Repair 2.0
3301 KIT, MATERIAL Remove/Install 1.0
HANDLING
3301 KIT, CALIBER .50 Remove/Install 1.0
MACHINE GUN
MOUNT
3301 KIT, M66 RING MOUNT Remove/Install 1.0
3301 KIT, 7.62 MACHINE Remove/Install 1.0
GUN MOUNT
3301 KIT, TURN SIGNAL Remove/Install 4.0
47 GAUGES (NON-
ELECTRICAL)
4701 SHAFT, ASSEMBLY Replace .5
FLEXIBLE
Repair .2
0540 00-17 Change 1

TM 9-2350-247-20-3
(4)
(1) (2) (3) (5) (6)
MAINTENANCE LEVEL
C O F H D REF CODE
76 FIXED FIRE
EXTINGUISHER
SYSTEM
7603 CONTROLS, FIXED Adjust .2
FIRE EXTINGUISHER
Replace .4
Repair .5
7603 CYLINDER Service .4
Replace .2
Change 1 0540 00-18

TM 9-2350-247-20-3
Table 2. TOOLS AND TEST REQUIREMENTS, SECTION III
EQUIPMENT MAINTENANCE NATIONAL TOOL

NOMENCLATURE
REF CODE LEVEL STOCK NUMBER NUMBER
1 O SLING, POWER PACK: USED TO LIFT 4910-00-646-6893 10942647
POWER PLANT, ENGINE AND (19207)
DIFFERENTIAL (M548A1 ONLY)
2 F MANOMETER: USED WITH 4720-00- 6685-00-065-5308 KM-J-2147
271-9839 HOSE, 6810-00-290-0017 (33287)
MERCURY, AND 8950-00-823-7664
FOOD COLORING TO CHECK
CRANKCASE PRESSURE, EXHAUST
BACK PRESSURE, AIR BOX
PRESSURE, AND AIR INTAKE
RESTRICTIONS
3 F HOSE, RUBBER: USED WITH 6685-00- 4720-00-271-9839 M6855/4-10L089
065-5308 MANOMETER (81349)
4 F MERCURY: USED WITH 6685-00-065- 6810-00-290-0017
5308 MANOMETER
5 F FOOD COLORING, LIQUID, RED 8-OZ: 8950-00-823-7664 MIL-F-35093
USED WITH 6685-00-065-5308 (81349)
MANOMETER
6 F GAUGE ASSEMBLY: USED WITH 4910-00-870-6283 10899180
4910-00-019-5241 ADAPTER TO (19207)
CHECK CYLINDER COMPRESSION
7 F ADAPTER: USED WITH 4910-00-870- 4910-00-019-5241 10934456
6283 GAUGE ASSEMBLY TO CHECK (19207)
CYLINDER COMPRESSION
8 H CRADLE ASSEMBLY: USED WITH 4910-00-795-0198 7950198 (19207)
4910-00-737-0432 AND 4910-00-789-
1017 BRACKETS AND WITH 4910-00-
985-0189 BRACKETS TO SUPPORT
ENGINE OUT OF CARRIER FOR
MAINTENANCE
9 H STAND, ENGINE MAINTENANCE: 4910-00-795-0189 7950189 (19207)
USED WITH 4910-00-795-0198 CRADLE
ASSEMBLY, AND WITH 4910-00-737-
0432 AND 4910-00-737-1017
BRACKETS TO SUPPORT ENGINE
OUT OF CARRIER FOR
MAINTENANCE
0540 00-19 Change 1

TM 9-2350-247-20-3

NOMENCLATURE
10 H BRACKET, FRONT: USED FOR 2520-01-006-4589 11678105
MOUNTING ENGINE IN 4910-00-795- (19207)
0189 CRADLE ASSEMBLY
11 F STUD: USED TO ALIGN CYLINDER 4910-00-591-6634 KM-J-9665
HEAD (33287)
12 H INSTALLER BODY, INJECTOR: USED 4940-00-711-1918 B-1088189
WITH 4940-00-711-1918 INSTALLER (19207)
BODY TO INSTALL INJECTOR TUBE
13 H INSTALLER PILOT, INJECTOR: USED 4940-00-711-1919 10881896
WITH 4940-00-711-1918 INSTALLER (19207)
BODY TO INSTALL INJECTOR TUBE
14 H INSTALLER FLARING DIE, 4940-00-711-1920 10881892
INSTALLER: USED WITH 4910-00-711- (19207)
1918 INSTALLER BODY TO FLARE
SMALL END OF INJECTOR TUBE
15 H REMOVER, CYLINDER LINER 5120-00-937-6140 J22490 (33287)
16 H EXPANDER, FRONT OIL SEAL: USED 4910-00-591-6640 10949378
TO EXPAND CRANKSHAFT FRONT (19207)
OIL SEAL WHEN INSTALLING
ENGINE LOWER FRONT COVER
17 H EXPANDER: USED TO EXPAND 5120-00-918-0587 KM-J-9769
REAR OIL SEAL (33287)
18 F HOOK, LIFTING: USED TO LIFT 4910-00-722-3877 10881880
FLYWHEEL (19207)
19 H STUD: USED TO ALIGN FLYWHEEL 5120-00-872-6015 KM-J-7540
HOUSING OR ENGINE LOWER FRONT (33287)
COVER
20 H CLAMP SET: USED TO LOCATE 5120-00-999-8618 J-21793 (33287)
CYLINDER LINERS WHEN
INSTALLING PISTONS
21 H COMPRESSOR, PISTON RING: USED 5120-00-901-8651 KM-J-6883
TO COMPRESS PISTON RINGS WHEN (33287)
INSTALLING PISTON IN CYLINDER
LINER
22 H REMOVER AND REPLACER: USED 5120-00-494-1846 KM-J-8128
TO REMOVE AND INSTALL PISTON (33827)
RINGS
Change 1 0540 00-20

TM 9-2350-247-20-3

NOMENCLATURE
23 H PISTON RING RETAINER: USED TO 5120-00-733-8874 10881874
REPLACE PISTON PIN RETAINERS (19207)
24 H REMOVER AND REPLACER: USED 5180-00-591-6630 10949461
TO REMOVE AND INSTALL (19207)
CAMSHAFT BEARINGS
25 H PULLER KIT: USED TO REMOVE 5120-00-338-6721 8708724 (19207)
CAMSHAFT GEAR AND BLOWER
GEARS
26 H PULLER, MECHANICAL: USED TO 5120-00-740-3345 KM-J-4871
REMOVE CRANKSHAFT TIMING (33287)
GEAR
27 H REPLACER, CRANKSHAFT TIMING 4910-00-736-1371 10949377
GEAR: USED TO INSTALL (19207)
CRANKSHAFT TIMING GEAR ON
CRANKSHAFT
28 F REMOVER, VALVE GUIDE: USED TO 4910-00-591-6632 KM-J-777
REMOVE VALVE GUIDE (33287)
29 F REPLACER, VALVE GUIDE: USED TO 5120-00-872-6014 KM-J-972
INSTALL VALVE GUIDE (33287)
30 H REPLACER, VALVE SEAT INSERT: 4910-00-603-8925 10949451
USED TO INSTALL VALVE SEAT (19207)
INSERTS IN CYLINDER HEAD
31 H TOOL KIT, VALVE SEAT INSERT: 5180-00-591-6631 10949470
USED TO REMOVE VALVE SEAT (19207)
INSERTS
32 F COMPRESSOR, VALVE SPRING: 5120-00-733-8888 10881882
USED WITH 5120-00-999-4052 (19207)
COMPRESSOR TO REMOVE
EXHAUST VALVE SPRINGS
33 F ADAPTER, VALVE SPRING 4910-00-918-0583 J-7455-4 (33287)
COMPRESSOR: USED WITH 5120-00-
733-8888 COMPRESSOR TO REMOVE
EXHAUST VALVE SPRINGS
34 F GAUGE, THICKNESS: USED TO 5120-00-273-8527 KM-J-9708
CHECK VALVE CLEARANCE (33287)
35 H INSTALLER, OIL PUMP DRIVE GEAR: 4910-00-591-6639 10949379
USED TO INSTALL OIL PUMP DRIVE (19207)
GEAR
0540 00-21 Change 1

TM 9-2350-247-20-3

NOMENCLATURE
36 H TEST FIXTURE: USED WITH 4910-00- 4910-00-355-6248 65-928-B
255-4681 TESTER TO TEST (92372)
INJECTORS
37 H ADAPTER, NEEDLE VALVE: USED 4910-00-764-5626 YA-396 (05083)
WITH 4910-00-355-6248 TEST FIXTURE
38 F REMOVER, INJECTOR: USED TO 5120-00-219-8400 10881891
REMOVE INJECTOR ASSEMBLY (19207)
FROM CYLINDER HEAD
39 H REAMER: USED TO CLEAN FLAT 5110-00-019-5240 10881903
PORTION OF INJECTOR NUT SPRAY (19207)
TIP SEAT
40 H REAMER, SECOND OPERATION: 5110-00-294-4606 10881907
USED TO CLEAN INJECTOR COPPER (19207)
TUBE
41 H REAMER: USED TO REAM CARBON 5110-00-219-8399 5344968 (33287)
FROM INJECTOR SPRAY TIP
42 H REAMER, FIRST OPERATION: USED 5110-00-785-1016 10881897
TO CLEAN INJECTOR SPRAY TUBE (19207)
43 H REMOVER, SPRAY TIP: USED TO 5120-00-355-6167 10919988
REMOVE SPRAY TIP FROM (19207)
INJECTOR NUT
44 H REFINISHER, INJECTOR TUBE TIP: 5120-00-785-1017 10881902
USED TO FACE SMALL END OF (19207)
INJECTOR TUBE
45 H GAUGE: USED TO TIME INJECTOR 5220-00-387-9581 10881887
(19207)
46 F GAUGE, FUEL PRESSURE: USED TO 6620-00-671-4509 10934455
CHECK FUEL PUMP OUTPUT (19207)
PRESSURE
47 O WRENCH, OPEN END AND BOX-END: 5120-00-740-3347 10949344
USED TO TORQUE FUEL RETURN (19207)
LINE NUTS
48 O TOOL, RADIATOR CLEANING: USED 4910-00-611-6559 11678393
TO CLEAN RADIATOR (19207)
49 H LIFTING STRAP: USED WITH 4910-00- 4910-00-572-8608 8356175 (19207)
Change 1 0540 00-22

TM 9-2350-247-20-3

NOMENCLATURE
673-3801 ADAPTER TO CHECK
CONVERTER MOUNTING SPACING
OR REMOVE OR INSTALL
CONVERTER DRIVE COVER
50 H HOLDER, STATOR ROLLERS: USED 4910-00-572-8688 8356195 (19207)
TO HOLD STATOR ROLLERS AND
SPRING DURING ASSEMBLY
51 H EYE, LIFTING: USED WITH 4910-00- 4910-00-673-3801 1086573 (19207)
572-8606 STRAP TO LIFT HIGH
RANGE CLUTCH PACKAGE AND
52 H HANDLE, REPLACERS: USED WITH 5120-00-316-9182 7950864 (19207)
5120-00-572-8660, 5120-00-572-8658,
5120-00-572-8615, 5120-00-572-8656,
AND 5120-00-759-5415 REPLACERS TO
INSTALL FRONT OIL PUMP SEAL,
HIGH CLUTCH HOUSING BUSHING,
OUTPUT BEARING AND SEAL,
BUSHING AND OUTPUT SHAFT
BUSHING
53 H REPLACER: USED WITH 5120-00-316- 5120-00-572-8656 8356202 (19207)
9182 HANDLE TO INSTALL HIGH-
RANGE CLUTCH HOUSING BEARING
(DRIVER PLUG)
54 H SNAP RING DRIVER KIT: USED TO 5120-00-572-8663 8356191 (19207)
INSTALL TURBINE SHAFT SNAP
RINGS
55 H PULLER BOLT: USED TO REMOVE 4910-00-572-8699 8356200 (19207)
GROUND SLEEVE ASSEMBLY
56 F REPLACER: USED WITH 5120-00-316- 5120-00-572-8615 8356185 (19207)
9182 HANDLE TO INSTALL OUTPUT
BEARING AND OIL SEAL (DRIVER
PLUG BEARING)
57 F PULLER: USED TO REMOVE REAR 5120-00-572-8712 8356201 (19207)
SEAL
58 F KIT, PRESSURE GAUGE: USED TO 4910-00-572-8612 8356176 (19207)
CHECK TRANSMISSION OIL
PRESSURE
59 F SLING, TRANSMISSION: USED TO 4910-00-572-8614 8356184 (19207)
0540 00-23 Change 1

TM 9-2350-247-20-3

NOMENCLATURE
LIFT TRANSMISSION AND TO
MOUNT TRANSMISSION IN STAND
(ADAPTER HOIST)
60 H COMPRESSOR, CLUTCH PACKAGE: 4910-00-572-8643 8356187 (19207)
USED TO HOLD CLUTCH PACKAGE
DURING REMOVAL OR
INSTALLATION, OR TO COMPRESS
REVERSE CLUTCH PACKAGE
DURING REMOVAL OR
INSTALLATION OF HOLDING PIN
61 H KIT, REMOVER AND REPLACER: 5120-00-572-8607 8356170 (19207)
USED TO REMOVE AND INSTALL
CLUTCH PISTON RETURN SPRING
RETAINING RING
9182 HANDLE TO INSTALL HIGH-
RANGE CLUTCH HOUSING BEARING
63 H BOLT: USED TO HOLD 4910-00-572-8701 8356186 (19207)
INTERMEDIATE-RANGE CLUTCH
BACKPLATE DURING DISASSEMBLY
AND ASSEMBLY
64 H SET, GUIDE BOLT: USED TO 4910-00-572-8710 8356165 (19207)
POSITION FRONT AND REAR OIL
PUMPS, FRONT AND REAR PILOT
TUBES AND DIAPHRAGM
9182 HANDLE TO INSTALL FRONT
OIL PUMP SEAL
66 H REPLACER: USED TO INSTALL 5120-00-776-1864 10886353
TRANSFER GEARCASE RETAINER (19207)
AND HOUSING BEARING CUPS
67 O BAR LIFTING: USED TO REMOVE 5120-00-918-0586 11589384
AND INSTALL FINAL DRIVE (19207)
TO REMOVE AND INSTALL OUTPUT (19207)
SHAFT BEARING
Change 1 0540 00-24

TM 9-2350-247-20-3

NOMENCLATURE
TO REMOVE AND REPLACE FINAL (19207)
DRIVE OUTPUT SHAFT OIL SEAL
70 F REMOVER AND REPLACER, OIL 5120-00-771-7018 10875326
SEAL: USED TO REMOVE AND (19207)
REPLACE FINAL DRIVE OUTPUT
SHAFT SPACER, RETAINER AND
BEARING; AND WITH 5315-00-834-
0118 PIN AND 5120-00-678-2796
REPLACER
71 F PIN, STRAIGHT, HEADLESS: USED 5315-00-834-0118 MS16556-3
WITH 5120-00-771-7018 REMOVER (96906)
AND REPLACER
72 0 ADAPTER, TORQUE WRENCH: USED 5120-00-977-7421 1091766 (19207)
TO TIGHTEN POWER-TRAIN
UNIVERSAL JOINT SCREWS
73 F SOCKET, SOCKET-WRENCH: USED 5120-00-557-8171 11633523
TO REMOVE AND INSTALL MASTER (19207)
CYLINDER RESILIENT VALVE
74 H TOOL, DIFFERENTIAL BACKLASH: 5120-00-074-1164 10942815
USED IN CONJUNCTION WITH DIAL (19207)
INDICATOR AS ALIGNING TOOL
75 H DRIVER PLUG, BEARING AND 5120-00-649-8126 10865981
BUSHING: USED TO REMOVE AND (19207)
INSTALL RIGHT-ANGLE DRIVE
PINION INNER AND OUTER
BEARINGS
WITH 5120-00-678-2798 REMOVER (19207)
AND REPLACER TO REMOVE RIGHT-
ANGLE PINION GEAR FROM
HOUSING
77 H REMOVER AND REPLACER, SLEEVE, 5120-00-678-2789 10865770
SNAP RING: USED TO REPLACE (19207)
RIGHT ANGLE-DRIVE HUB BEARING
0540 00-25 Change 1

TM 9-2350-247-20-3

NOMENCLATURE
78 O REMOVER AND REPLACER: USED 5120-00-678-2798 8763117 (19207)
TO REMOVE RIGHT ANGLE DRIVE
PINION GEAR; USED WITH 5120-00-
649-8140 SLEEVE TO REMOVE
RIGHT-ANGLE DRIVE CARRIER AND
OUTER BEARING; AND TO REPLACE
RIGHT-ANGLE DRIVE PINION
BEARING CAP OIL SEAL OR
DIFFERENTIAL SHAFT BEARING CAP
OIL SEAL; REMOVE AND INSTALL
IDLER AND ROAD WHEEL ARM
HOUSING BEARINGS AND OIL SEAL
79 O REPLACER, WHEEL HUB BEARING 5120-00-678-2796 10863002
CUP: USED TO INSTALL IDLER AND (19207)
ROAD WHEEL HUB INNER AND
OUTER BEARING CUPS
80 O GAUGE, SPROCKET WEAR: USED TO 5120-01-041-9920 12253280
CHECK DRIVE SPROCKET WEAR, (19207)
TRACK BUSHING WEAR, AND
TRACK TENSION
81 O FIXTURE, TRACK CONNECTING: 5120-01-041-4624 12253183
USED TO DISCONNECT AND (19207)
CONNECT TRACKS (2 EACH)
82 O PIN, DRIFT: USED TO DISCONNECT 5120-01-006-8847 11678718
TRACKS (19207)
83 F REMOVER AND REPLACER: USED 5120-00-966-5951 1094246 (19207)
TO REMOVE AND INSTALL PIVOT
STEER PISTON DRAG UNIT
84 O REMOVER, SHOCK ABSORBER: 5120-00-710-8075 12269380
USED TO REMOVE SHOCK (19207)
ABSORBER
85 H TOOL SET: USED TO REMOVE AND 5180-00-966-5961 10932474
REPLACE OVERSIZE ROSAN INSERTS (19207)
86 H REMOVER, FUEL VALVE SCREEN: 5120-00-735-5871 735871 (19207)
USED TO REMOVE HEATER FUEL
VALVE SCREEN
87 H SCRAPER, CARBON: USED TO 5120-00-735-5872 7355872 (19207)
REMOVE CARBON FROM HEATER
COMBUSTION CHAMBER
Change 1 0540 00-26

TM 9-2350-247-20-3

NOMENCLATURE
88 O ADAPTER, PULLER: USED WITH 5120-00-933-8458 11592843
5120-00-557-3615 PULLER (19207)
89 O TOOL KIT, ELECTRONIC 5180-00-575-0716 SC4931-
MAINTENANCE (LI W37913) 95CLA13
(19204)
90 H LIFTING SLING 5340-01-247-3070 3383W265
(23755)
91 H RECESSED TIPS ALIGNMENT TOOL 5120-00-293-0644 8722 (22653)
92 O PLIERS, ELEC CON 5120-00-624-8065 AT508K (00784)
93 O ADJ, STEER CENTERING: USED FOR 2530-01-249-6439 J35223 (25341)
M548A3 CROSS DRIVE
TRANSMISSION
94 F SHOT EQUIP, SUPPL #1 4910-00-754-0706 SC4910-95-A62
95 FO SHOP EQUIP, COM #2 4910-00-754-0650 SC4910-95-A72
96 FO SHOP EQUIP, COM #1 4910-00-754-0654 SC4910-95-A74
97 O TOOL SET, SUPPL #2 4940-00-754-0743 SC4910-95-A08
98 FHO TOOL KIT, GEN MECH 5180-00-177-7033 SC5180-90-N26
99 FO CAULKING GUN 5120-00-679-5655 101 (06798)
100 O BAR, LIFTING FINAL DRIVE 5120-00-918-0586 11589384
(19207)
101 O GAUGE, OIL TESTER 6695 01-242-6795 11650182
(19207)
102 FO ADAPTER, TORQUE WRENCH 5120-00-213-6976 11663358-1
(19207)
103 F STAND, ENGINE AND TRANS: USED 4910-01-239-6836 12349616
FOR M548A3 POWERPLANT (19207)
104 FO SLING, ENGINE AND TRANS: USED 1450-01-240-2206 12350306
FOR M548A3 POWERPLANT (19207)
105 O TENSIOMETER, V-BELT: USED FOR 6635-00-921-6255 12998F (24161)
M548A3 FAN AND GENERATOR
BELTS
106 O TEST SET, STE/ICE 4910-01-222-6589 12259266
(19207)
0540 00-27 Change 1

TM 9-2350-247-20-3

NOMENCLATURE
107 FO MULTIMETER 6625-01-265-6000 27/FMW/ACE
(89536)
108 FHO SHOP EQUIP, FLD BSC 4910-00-754-0705 SC4910-95-A31
(19204)
109 H BLADE THICKNESS GAUGE 5210-01-048-7085 J23185 (33287)
110 H SHIELD, TURBO INLET 4910-01-127-7959 J26554-A
(33287)
111 F WRENCH, RETAINING NUT 5120-00-808-5230 J5895 (33287)
112 F PRIMER, FUEL SYSTEM 4910-00-402-9623 J5956 (33287)
113 H TESTER, DIESEL FUEL 4910-00-255-8641 3YFL (05008)
114 F WELDING SHOP, TLRMTD 3431-01-090-1231 SC3431-95-A04
(19204)
115 F TOOL KIT, BODY AND FENDER 5180-00-754-0643 7540643 (19204)
116 O CROWFOOT ATTACHMENT 5120-00-184-8397 AN8506-3
(55719)
Change 1 0540 00-28

TM 9-2350-247-20-3
MAINTENANCE ALLOCATION CHART (MAC) 0540 00
Table 3. REMARKS, SECTION IV

REMARKS
REMARKS
CODE
A THE POWER PLANT IS REMOVED AND INSTALLED FOR AUTHORIZED MAINTENANCE
THAT CANNOT BE DONE ON ITEMS IN THE POWER PLANT COMPARTMENT WITH THE
POWER PLANT IN PLACE. THE POWER PLANT IS NOT AN AUTHORIZED REPLACEMENT
PART.
B COMPLETE REPAIR IS AUTHORIZED AT GENERAL SUPPORT MAINTENANCE. SEE TM
9-2350-247-24P FOR PARTS REPLACED AT UNIT MAINTENANCE. SEE TM 9-2815-205-34P
FOR PARTS REPLACED AT DIRECT SUPPORT MAINTENANCE.
C REPAIR IS LIMITED TO PARTS LISTED IN TM 9-2350-247-24P.
D REPAIR IS LIMITED TO PARTS AUTHORIZED IN TM 9-2350-247-24P.
E COMPLETE REPAIR IS AUTHORIZED AT DIRECT SUPPORT MAINTENANCE. SEE TM 9-
2350-247-24P FOR PARTS REPLACED AT UNIT MAINTENANCE.
F REPAIR IS LIMITED TO PARTS LISTED IN TM 9-2920-225-34P FOR 100 AMP GENERATOR, IN
TM 9-2920-257-30&P FOR 200 AMP GENERATOR.
G REPAIR IS LIMITED TO REPLACEMENT OF PARTS LISTED IN TM 9-2815-205-34P.
H COMPLETE REPAIR IS AUTHORIZED AT GENERAL SUPPORT MAINTENANCE. SEE TM 9-
2350-247-24P FOR PARTS REPLACED BY UNIT MAINTENANCE. SEE TM 9-2520-254-34P FOR
PARTS REPLACED BY DIRECT SUPPORT MAINTENANCE.
I COMPLETE REPAIR IS AUTHORIZED AT GENERAL SUPPORT MAINTENANCE. SEE TM 9-
2350-247-24P FOR PARTS REPLACED BY UNIT MAINTENANCE. SEE TM 9-2520-238-34P FOR
PARTS REPLACED BY DIRECT SUPPORT MAINTENANCE.
J TRACK SHOE REMOVAL MAY BE REQUIRED TO ADJUST THE TRACK PROPERLY. THE
TRACK ASSEMBLY IS NOT AUTHORIZED AS A REPAIR PART.
K SEE TM 9-2350-261-10 AND TB 750-651 FOR CREW SERVICE.
L THE ASSEMBLY IS NOT AUTHORIZED AS A REPAIR PART.
M REFER TO TM 9-2350-238-34 FOR ITEM MAINTENANCE INFORMATION.
P COMPLETE REPAIR IS AUTHORIZED AT GENERAL SUPPORT MAINTENANCE. SEE TM 9-
2350-247-24P FOR MOUNTING COMPONENTS. SEE TM 9-2350-238-34P FOR COMPONENT
PARTS.
Q THE POWER PLANT HAS TO BE REMOVED TO PERFORM THE REPLACE TASK.
R COMPLETE REPAIR IS AUTHORIZED AT GENERAL SUPPORT MAINTENANCE. SEE TM 9-
2350-247-24P FOR PARTS REPLACED BY ORGANIZATIONAL MAINTENANCE. SEE TM 9-
2520-272-34&P FOR PARTS REPLACED BY DIRECT SUPPORT MAINTENANCE.
S IF SERVICING IS REQUIRED, THE FAN NEEDS TO BE REMOVED TO ADD OIL.
T EXHAUST DUCTS NEED TO BE REMOVED TO PERFORM TASK.
0779 00-29 Change 1

TM 9-2350-247-20-3
REMARKS
REMARKS
CODE
U GENERATOR OR ENGINE STARTER CAN BE REACHED THROUGH BOTTOM HULL ACCESS
COVER (M548A3)
V REFER TO TM 9-2540-205-24&P FOR MAINTENANCE PROCEDURES, REPAIR PARTS, AND
MAINTENANCE ALLOCATION CHART (MAC).
W REFER TO TM 9-2540-207-14&P FOR MAC, MAINTENANCE TASKS, AND REPAIR PARTS.
X REFER TO TB 750-651 FOR CREW/UNIT SERVICE.
Y COMPLETE REPAIR IS AUTHORIZED AT GENERAL SUPPORT MAINTENANCE. SEE TM 9-
2350-247-24P FOR PARTS REPLACED BY UNIT MAINTENANCE. SEE TM 9-2520-272-34&P
FOR PARTS REPLACED BY DIRECT SUPPORT MAINTENANCE.
Z REFER TO TM 9-2815-205-34 FOR MAINTENANCE PROCEDURES AND TOOLS.
Change 1 0540 00-30

TM 9-2350-247-20-3
COMMON TOOLS AND SUPPLEMENTS AND SPECIAL 0541 00

TOOLS/FIXTURES LIST
INTRODUCTION
Scope
This work package lists all common tools, supplements and special tools/fixtures needed to maintain the M548A1 and
M548A3 carriers.
Explanation of Columns
Column (1) — Item Number. This number is assigned to the entry in the listing and is referenced in the Initial Setup section
of the task under Tools to identify the item (e.g., “Torque wrench (WP 0541 00, Item 72)”).
Column (2) — Name. This column lists the item by noun nomenclature and other descriptive features (e.g., “Bracket, angle,
lifting”).
Column (3) — National Stock Number. This is the National Stock Number (NSN) assigned to the item; use it to requisition
the item.
Column (4) — Part Number. Indicates the primary number used by the manufacturer (individual, company, firm, corporation,
or Government activity), which controls the design and characteristics of the item by means of its engineering drawings,
specifications, standards, and inspection requirements to identify an item or range of items.
Column (5) — Reference. This column identifies the authorizing Supply Catalog (SC) or Repair Parts and Special Tools List
(RPSTL) for items listed in this work package.
Table 1. Tool Identification List
(1) (2) (3) (4) (5)

ITEM NATIONAL STOCK PART
NO. ITEM NAME NUMBER NUMBER REFERENCE
1 ADAPTER, SOCKET, WRENCH 5120-00-227-8088 SH-131 EM 0074
2 ADAPTER, TORQUE WRENCH, 1/2 IN 5120-00-977-7421 10917666 TM 9-2350-247-24P
DRIVE, 9/16 IN
3 ADAPTER, TORQUE WRENCH, 7C 5120-00-213-6976 11663358-1 TM 9-2350-247-24P
U-JOINT
3A ADAPTER, TORQUE WRENCH, 6C 5120–00–215–8200 11663358–2 TM 9-2350-247-24P
U-JOINT
4 ADAPTER, TORSION BAR 5120-01-017-5328 12251805 TM 9-2350-247-24P
5 ADJUSTING TOOL, STEER 2530-01-249-6439 J35223 TM 9-2350-247-24P
CENTERING
6 ANALYZER SET, ENGINE STE/ICE-R 4910-01-222-6589 12259266 TM 9-4910-571-12&P
7 BAR, LIFTING, FINAL DRIVE 5120-00-918-0586 11589384 TM 9-2350-247-24P
8 BLADE, HAND HACKSAW 5110-00-277-4588 31-51024 SC 4910-95-A74
9 CAN, RADIATOR FILLING 7240-00-499-8028 MIL-C- TM 9-2350-247-24P
43522
10 CLEANING TOOL, RADIATOR 4910-00-611-6559 11678393 TM 9-2350-247-24P
11 CRIMPING TOOL, TERMINAL 5120-00-432-7836 MY28 TM 9-2350-247-24P
12 DISPENSER, SEALANT 5120-00-679-5655 101 TM 9-2350-247-24P
0541 00-1
Change 1
TM 9-2350-247-20-3
COMMON TOOLS AND SUPPLEMENTS AND SPECIAL TOOLS/FIXTURES 0541 00

LIST — Continued
(1) (2) (3) (4) (5)

13 DRILL, PORTABLE ELECTRIC, 1/2 IN 5130-00-293-1849 W-D-661 SC 4910-95-A74
14 DRILL SET, TWIST 5133-00-293-0983 DB129B SC 4910-95-A74
15 FITTING KIT, TUBE-PIPE 4730-00-470-6625 51025 SC 4910-95-A74
16 FIXTURE, TRACK CONNECTING 5120-01-041-4624 12253183 TM 9-2350-247-24P
17 FRAME, HAND HACKSAW 5110-00-289-9657 163-20 SC 4910-95-A74
18 GAUGE, TENSION 6635-00-921-6255 12998F TM 9-2350-247-24P
19 GAUGE, TRACK AND SPROCKET 5220-01-041-9920 12253280 TM 9-2350-247-24P
20 GLOVES, WELDER’S 8415-00-268-7859 A-A-50022 EM 0074
21 GOGGLES, INDUSTRIAL 4240-00-052-3776 A-A-1110 SC 4910-95-A74
22 GUN, AIR BLOW 4940-00-333-5541 DGA520 SC 4910-95-A74
23 GUN, SOLDERING 3439-00-618-6623 D550-3 SC 4910-95-A74
24 HAMMER, SOFT HEAD 5120-01-065-9037 TM 9-2350-247-24P
25 HEATER, GUN TYPE, ELECTRIC 4940-00-561-1002 500A SC 5180-95-B19
26 HELMET, WELDER’S 4240-00-540-0623 A-A-1994 EM 0074
27 LIFTER, ROAD WHEEL (T130 TRACK) 5120-01-062-5607 12268612 TM 9-2350-247-24P
27A LIFTER, ROAD WHEEL (T150 TRACK) 5120-01-496-3694 12474852 TM 9-2350-247-24P
28 MIRROR, INSPECTION 5120-00-596-1098 24 TM 9-2350-247-24P
29 MULTIMETER 6625-01-139-2512 T00377 SC 4910-95-A74
30 PLIERS, RETAINING RING 5120-00-288-9717 2104893 SC 4910-95-A74
31 PLIERS, RETAINING RING 5120-00-293-0046 0500 SC 4910-95-A74
32 PLIERS, SET, RETAINING 5120-00-789-0492 4440R SC 4910-95-A74
33 PLIERS, SLIP JOINT 5120-00-624-8065 AT508K TM 9-2350-247-24P
34 PRESSURE GAUGE KIT 6695-01-242-6795 11650182 TM 9-2350-247-24P
35 PULLER, BATTERY TERMINAL 5120-00-944-4268 21 SC 4910-95-A74
36 PULLER, MECHANICAL 5120-00-595-9305 GGGP781 SC 4910-95-A74
37 PULLER, SLIDE 5120-00-557-3615 5573615 TM 9-2350-247-24P
38 PUNCH, DRIVE PIN 5120-01-006-8847 11678718 TM 9-2350-247-24P
39 REMOVER AND REPLACER 5120-00-678-2798 8763117 TM 9-2350-247-24P
40 REMOVER AND REPLACER 5120-00-740-3346 10943279 TM 9-2350-247-24P
41 REPLACER, GREASE CAP 5120-00-678-2796 10863002 TM 9-2350-247-24P
42 RIVETER, BLIND, HAND KIT 5120-01-289-4310 HP-2 SC 4910-95-A74
43 SCALE, WEIGHING 6670-00-254-4634 AAA-S-133 SC 4910-95-A74
0541 00-2
Change 1
TM 9-2350-247-20-3

LIST — Continued
(1) (2) (3) (4) (5)

44 SCREW, CAP, SOCKET HEAD 5305-00-983-7456 MS16998-97 TM 9-2350-247-24P
45 SLING, BEAM TYPE 4910-00-646-6893 10942647 TM 9-2350-247-24P
46 SLING, ENDLESS 3940-00-675-5003 PD101-96 TM 9-2350-247-24P
47 SLING, ENGINE AND TRANSMISSION 3940-01-240-2206 12350306 TM 9-2350-247-24P
48 SOCKET, SOCKET WRENCH SPLINED 5120-00-906-1051 8355955 TM 9-2350-247-24P
49 SPACER, RING 5365-00-004-0763 10863001 TM 9-2350-247-24P
50 STRAIGHT EDGE 5120-00-264-6400 MIL-S- TM 9-2350-247-24P
15769 TYPE
2
51 STRIPPER, WIRE, HAND 5110-00-268-4224 GA116 TM 9-2350-247-24P
52 TAPE, MEASURING 5120-00-554-7085 GGG-T-106 TM 9-2350-247-24P
53 TEST KIT, GENERATOR 6625-01-505-5996 12358697 TM 9-2350-247-24P
54 TEST KIT, RADIATOR 4910-00-728-8227 ST255A TM 9-2350-247-24P
55 TESTER, ANTIFREEZE AND BATTERY 6630-00-105-1418 10425 SC 4910-95-A74
56 TOOL KIT, ELECTRICAL 5180-00-876-9336 7550526 SC 4910-95-A74
57 TOOL KIT, GENERAL MECHANIC’S 5180-00-177-7033 SC5180-90- SC 5180-90-N26
CL-N26
58 TOOL, SHOCK ABSORBER 5210-01-102-4268 12269380 TM 9-2350-247-24P
58A TOOL, TRACK PIN ALIGNMENT 5220-01-504-2610 12474881 TM 9-2350-247-24P
59 V-BELT, TENSIOMETER, DIAL ENGINE 6635-01-093-3710 J23600-B TM 9-2350-247-24P
60 WRENCH, OPEN END BOX 5120-00-740-3347 10949344 TM 9-2350-247-24P
61 WRENCH, PIPE, 10 IN 5120-00-277-1485 GGG-W-651 TM 9-2350-247-24P
62 WRENCH SET, OPEN END 5120-00-148-7918 GGG-W-636 SC 4910-95-A74
63 WRENCH SET, SOCKET, 1/4 IN DRIVE 5120-00-081-2305 GGG-W-641 SC 4910-95-A74
64 WRENCH SET, SOCKET, 3/8 IN DRIVE 5120-00-322-6231 GGG-W-641 SC 4910-95-A74
65 WRENCH SET, SOCKET, 3/4 IN DRIVE 5120-00-204-1999 FED STD EM 0074
353
66 WRENCH, SOCKET ATTACHMENT, 3/4 5120-00-053-3625 10932504 TM 9-2350-247-24P
IN DRIVE, 1-3/8 IN HEX
67 WRENCH, TORQUE, 1/4 IN DRIVE, 0-75 5120-01-112-9532 B107.14M SC 4910-95-A74
LB-IN TYICLCSTI
68 WRENCH, TORQUE, 1/2 IN DRIVE, 5120-00-247-2540 J-1313-B SC 4910-95-A74
0-150 LB-FT
0541 00-3
Change 1
TM 9-2350-247-20-3

LIST — Continued
(1) (2) (3) (4) (5)

69 WRENCH, TORQUE, 1/2 IN DRIVE, 5120-00-640-6364 1753LDF SC 4910-95-A74
0-170 LB-FT
70 WRENCH, TORQUE, 3/8 IN DRIVE, 5120-00-853-4538 F200I EM 0074
0-200 LB-IN
71 WRENCH, TORQUE, 3/8 IN DRIVE, 5120-00-542-5681 F600I3-8 SC 5180-95-A12
0-600 LB-IN
72 WRENCH, TORQUE, 3/4 IN DRIVE, 5120-00-221-7983 SW130-301 SC 4910-95-A74
0-600 LB-FT
0541 00-4
Change 1
TM 9-2350-247-20-3
EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST 0542 00
INTRODUCTION
Scope
This work package lists expendable supplies and materials you will need to maintain the M548A1 and M548A3 carriers.
These items are authorized to you by CTA 50-970, Expendable Items (Except Medical, Class V, Repair Parts, and Heraldic
Items).
Explanation of Columns in the Expendable/Durable Items List
Column (1) — Item Number. This number is assigned to the entry in the listing, and is referenced in the Initial Setup section
of the task under Materials/Parts to identify the item (e.g., “Antiseize compound (WP 0542 00, Item 6)”).
Column (2) — Level. This column identifies the lowest level of maintenance that requires the listed item.
O — Unit Maintenance
Column (3) — National Stock Number. This is the National Stock Number (NSN) assigned to the item. Use it to request or
requisition the item.
Column (4) — Description. Indicates the Federal item name and, if required, a description to identify the item. This column
also includes the Commercial and Government Entity Code (CAGEC) in parentheses followed by the part number.
Column (5) — Unit of Measure (U/M). Indicates the measure used in performing the actual maintenance function. This
measure is expressed by a two-character alphabetical abbreviation (e.g., ea, in, pr). If the unit of measure differs from the unit
of issue, requisition the lowest unit of issue that will satisfy the requirements.
Table 1. Expendable and Durable Items List
(1) (2) (3) (4) (5)

ITEM NATIONAL
NUMBER LEVEL STOCK NUMBER ITEM NAME, DESCRIPTION, CAGEC, PART NUMER U/M
1 O 8040-00-664-4318 ADHESIVE PT
(18876) 9995460
2 O 8040-01-068-2423 ADHESIVE PT
(94960) 2141PT
2.1 O 8040-00-843-0802 ADHESIVE (RTV) OZ
(80244) MIL-A-46106 GP1TY1
3 O 9150-00-985-7244 AIRCRAFT GREASE TU
(81349) MIL-G-23827
4 O 6850-00-181-7940 ANTIFREEZE DR
(81349) MIL-A-46153
5 O 6630-01-011-5039 ANTIFREEZE TEST KIT EA
(IBY35) 1208
6 O 8030-00-251-3980 ANTISEIZE COMPOUND LB
(05972) 76764
7 O 8030-00-577-4740 CAULKING COMPOUND GL
(81349) TT-C-1796
8 O 7920-00-044-9281 CLEANING CLOTH BX
(51200) MIRACLE WIPE L001
0542 00-1
Change 1
TM 9-2350-247-20-3
EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST — Continued 0542 00
(1) (2) (3) (4) (5)

ITEM NATIONAL
9 O 6850-01-277-0595 CLEANING COMPOUND CN
(59557) 134-HI-SOLV
10 O 5970-01-159-8000 ELECTRICAL INSULATING COMPOUND OZ
(83574) PR1568 AEROSOL
11 O 6810-00-249-9354 ELECTROLYTE SULFURIC ACID GL
(19207) 10875529
12 O 6810-00-236-0702 ELECTROLYTE SULFURIC ACID (TROPICAL) GL
(81348) 0-5-801
13 O 9150-01-152-4119 ENGINE LUBRICATING OIL DR
(81349) MIL-L-2104
14 O 9150-00-190-0905 GAA GREASE CN
(81349) MIL-G-10924
15 O 9150-00-231-2361 GENERAL PRESERVATIVE LUBRICATING OIL QT
(81349) PETROTEC 90B
16 O 7930-00-531-9715 GENERAL PURPOSE DETERGENT GL
(81349) MIL-D-16791
17 O 3439-00-076-1279 HEAT SINK COMPOUND EA
(28493) X-275
18 O 9150-01-131-3324 HYDRAULIC FLUID (FRH) GL
(81349) MIL-H-46170
19 O 5970-00-161-7422 INSULATING VARNISH GL
(24446) 1201
20 O 5970-00-063-1495 INSULATION SLEEVING FT
(38597) M23053/1-103-0
(81349) M23053/1-105-0
(81349) M23053/1-102-0
(81349) M23053/2-107-0
(81349) M23053/1-104-0
25 O 5970-00-816-6056 INSULATION TAPE FT
(81348) HH-I-595-B-108-0
26 O 9150-00-754-2595 MOLYBDENUM D GREASE LB
(11770) MIL-G-21164
27 O 9505-00-293-4208 NONELECTRICAL WIRE LB
(96906) MS20995C32
0542 00-2
Change 1
TM 9-2350-247-20-3
(1) (2) (3) (4) (5)

ITEM NATIONAL
28 O 4720-00-278-4892 NONMETALLIC HOSE FT
(19207) 12309272-4
29 O 6850-00-227-1887 OPTICAL LENS CLEANING COMPOUND QT
(81349) MIL-C-43454
30 O 8020-00-297-6657 PAINT BRUSH EA
(81348) H-B-491
31 O 8010-01-184-0334 POLYURETHANE COATING GL
(81348) TT-C-542
32 O 9320-00-272-2990 RUBBER ADHESIVE TAPE FT
(81349) MIL-T-6841
33 O 8030-00-088-7818 SEALING COMPOUND CN
(81349) MIL-S-7916
34 O 8030-00-148-9833 SEALING COMPOUND BX
(81349) MIL-S-46163, 10 CC BOTTLE
35 O 8030-00-159-8177 SEALING COMPOUND QT
(81349) MIL-S-12158
36 O 8030-00-247-2525 SEALING COMPOUND TU
(81349) MIL-S-45180
(81349) MIL-S-45180TY2
38 O 8030-00-841-6832 SEALING COMPOUND KT
(81349) MIL-S-8802
(05972) 567-47
40 O 8030-00-900-2373 SEALING COMPOUND PRIMER BT
(05972) MIL-S-22473
41 O 6810-00-264-6618 SODIUM BICARBONATE LB
(81348) O-S-576
42 O 3439-00-273-1637 SOLDER, 1/8 IN. LB
(81348) QQ-S-571
43 O 5975-00-111-3208 TIEDOWN STRAP EA
(96906) MS3367-5-9
44 O 3439-00-453-5472 TIN ALLOY SOLDER LB
(81348) SN60WRMAP2 0.036 1 LB
45 O 7920-00-205-1711 WIPING RAG BE
(58536) A-A-2522
46 O 9150-00-530-6814 WIRE ROPE GREASE CN
(81349) MIL-G-18458
0542 00-3
Change 1
TM 9-2350-247-20-3
(1) (2) (3) (4) (5)

ITEM NATIONAL
47 O 8030-00-081-2339 SEALING COMPOUND CC
(05972) 088-21 MIL-S-22473 GRA
48 O 8030-00-181-8372 SEALING COMPOUND PRIMER CN
(05972) 747-56 MIL-S-22473GRTFMR
0542 00-4
Change 1
TM 9-2350-247-20-3
INDEX
Subject WP Sequence No.-Page No.

A
Accelerator Linkage (M548A3)
Adjustment
Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0200 00-2
Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0200 00-4
Access Cover
Front (M548A3)
Installation . . . . . . . . . . . ................................................. 0391 00-2
Removal . . . . . . . . . . . . . ................................................. 0391 00-1
Fuel Compartment
Installation . . . . . . . . . . . ................................................. 0163 00-2
Removal . . . . . . . . . . . . . ................................................. 0163 00-1
Hull Bottom and Drain Cover
Installation . . . . . . . . . . . ................................................. 0383 00-3
Removal . . . . . . . . . . . . . ................................................. 0383 00-1
Power Plant Right Rear Seal
Installation . . . . . . . . . . . ................................................. 0389 00-2
Removal . . . . . . . . . . . . . ................................................. 0389 00-1
Top and Grilles (M548A1)
Installation . . . . . . . . . . . ................................................. 0390 00-2
Removal . . . . . . . . . . . . . ................................................. 0390 00-1
Air Box Drain

Check Valve and Tubes (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0136 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0136 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0134 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0134 00-1
Tubes (M548A1)
Installation . . . . . . . . . . . . . . . ............................................. 0135 00-2
Removal . . . . . . . . . . . . . . . . . ............................................. 0135 00-1
Air Box Heater

Electrode (M548A3)
Clean, Inspect, and Repair . . . . . . . . . . . . . . . .................................. 0188 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0188 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0188 00-2
Harness/Igniter Cable
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0182 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0182 00-1
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0183 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0183 00-1
Hoses, Tubes, and Fittings
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0180 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0180 00-1
M548A3
Inspection-Acceptance and Rejection Criteria ................................. 0181 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0181 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0181 00-1
Index-1 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Ignition Coil, Air Pump, Check Valve (M548A3)

Clean and Inspect . . . . . . . . . . . . . . . . . . . . ................................... 0185 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . ................................... 0185 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................... 0185 00-2
M548A1
Ignition Coil
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0184 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0184 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0189 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0189 00-1
Solenoid Valve
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . ................................... 0186 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ................................... 0186 00-1
M548A3
Clean and Inspect . . . . . . . . . . . . . . . . . . . ................................... 0187 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . ................................... 0187 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ................................... 0187 00-1
Air Box Heater Switch

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-2
Air Brake (M548A1)

Air Brake Panel Light
Installation . . . . . . . . . . . . . . .............................................. 0504 00-2
Removal . . . . . . . . . . . . . . . . .............................................. 0504 00-1
Air Brake Pressure Indicator
Installation . . . . . . . . . . . . . . .............................................. 0503 00-2
Removal . . . . . . . . . . . . . . . . .............................................. 0503 00-1
Air Hoses/Tubes/Fittings
Installation . . . . . . . . . . . . . . .............................................. 0495 00-9
Removal . . . . . . . . . . . . . . . . .............................................. 0495 00-1
Air Low Pressue Warning Light
Installation . . . . . . . . . . . . . . .............................................. 0502 00-2
Removal . . . . . . . . . . . . . . . . .............................................. 0502 00-1
Air Low Pressure
Installation . . . . . . . . . . . . . . .............................................. 0494 00-3
Removal . . . . . . . . . . . . . . . . .............................................. 0494 00-1
Compresser Drive Belt Guard
Installation . . . . . . . . . . . . . . .............................................. 0497 00-2
Removal . . . . . . . . . . . . . . . . .............................................. 0497 00-1
Compresser Drive Pulley/Belts
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0498 00-1
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0498 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0499 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0499 00-1
Compressor
Installation . . . . . . . . . . . . . . .............................................. 0489 00-4
Removal . . . . . . . . . . . . . . . . .............................................. 0489 00-2
Governor
Installation . . . . . . . . . . . . . . .............................................. 0490 00-2
Removal . . . . . . . . . . . . . . . . .............................................. 0490 00-1
Change 1 Index-2
TM 9-2350-247-20-3
INDEX, cont’d
Instrument Panel
Installation . . . ......................................................... 0501 00-2
Removal . . . . . ......................................................... 0501 00-1
Oil Hoses/Fittings
Installation . . . ......................................................... 0496 00-3
Removal . . . . . ......................................................... 0496 00-2
Reservoir
Installation . . . ......................................................... 0491 00-2
Removal . . . . . ......................................................... 0491 00-1
Safety Valve
Installation . . . ......................................................... 0492 00-2
Removal . . . . . ......................................................... 0492 00-1
Stoplight Switch
Installation . . . ......................................................... 0493 00-3
Removal . . . . . ......................................................... 0493 00-1
Strainer
Installation . . . ......................................................... 0500 00-2
Removal . . . . . ......................................................... 0500 00-1
Air Cleaner
M548A1
Element
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0152 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0152 00-2
Filter Indicator Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0154 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0154 00-2
Hose and Clamps
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0153 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0153 00-1
M548A3
Assembly and Related Parts
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0159 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0159 00-2
Door gasket
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0158 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0158 00-1
Elbow and Inlet Duct Assemblies
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0161 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0161 00-2
Exhaust Check Valve and Ejector Tube
Inspect and Repair . . . . . . . . . . . . . . . . . . . .................................. 0160 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0160 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0160 00-2
Filter Element
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0156 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0156 00-1
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0155 00-1
Indicator and Hose
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0157 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0157 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0157 00-2
Index-3 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Air Compressor
Compressor Air Output Adequate, but No Air Pressure Indication On Panel Air Brake Pressure Indicator
(M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0096 00-1
Compressor Does Not Maintain Air Pressure (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0098 00-1
Compressor Operation Too Noisy (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0102 00-1
Low Air Pressure Warning Light Does Not Light When Air Pressure Falls Below 60 PSI (414 KPA)
(M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0097 00-1
Too Much Foreign Matter In Reservoir (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0101 00-1
Too Much Oil Drainage From Reservoir Drain Cock (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . 0100 00-1
Towed Load Brakes Do Not Operate When Pedal Is Pressed; Air Pressure Adequate (M548A1) . 0099 00-1
Air Hoses/Tubes/Fittings, Air Brake (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0495 00-9
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0495 00-1
Air Low Pressure Switch, Air Brake (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0494 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0494 00-1
Air Low Pressure Warning Light, Air Brake (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0502 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0502 00-1
Air Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0191 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0191 00-1
Air Pump Vane Kit

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0190 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0190 00-1
Air Separator Tank

M548A1
Clean, Inspect, and Repair . . . . . . . . . . . . ..................................... 0170 00-5
Installation . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0170 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0170 00-2
Tubes, Hoses, and Fittings (to fuel tank)
Installation . . . . . . . . . . . . . . . . . . . . . ..................................... 0172 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0172 00-2
M548A3
Clean and Inspect . . . . . . . . . . . . . . . . . . ..................................... 0171 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0171 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0171 00-1
Tubes, Hoses, and Fittings (To Fuel Tank)
Clean and Inspect . . . . . . . . . . . . . . . . . ..................................... 0173 00-7
Installation . . . . . . . . . . . . . . . . . . . . . ..................................... 0173 00-8
Removal . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0173 00-2
Change 1 Index-4
TM 9-2350-247-20-3
INDEX, cont’d
Arm Assembly, Idler Wheel, Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0354 00-1
Auxiliary Power (Slave) Receptable

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0303 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0303 00-1
B
Battery
Battery and Battery Compartment (M548A1)
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0290 00-4
Inspection-Acceptance and Rejection Criteria . . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0290 00-4
Installation . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0290 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0290 00-2
Cable Jack to Regulator (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0299 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0299 00-2
Compartment Bracket (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0291 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0291 00-2
M548A3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0293 00-4
Installation . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0293 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0293 00-2
Negative Lead(s)
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0292 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0292 00-1
Battery Box Heat Exchanger/Hoses/Fittings

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0476 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0476 00-1
Battery-Generator Gauge
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0266 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0266 00-1
Beam Selector Switch

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0273 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0273 00-1
Belts, Safety
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0399 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0399 00-2
Bilge Pump
Bilge Pump System Schematic ................................................ 0083 00-1
Circuit Breaker
Installation . . . . . . . . . . . . ................................................ 0268 00-2
Removal . . . . . . . . . . . . . . ................................................ 0268 00-1
Cleaning . . . . . . . . . . . . . . . . ................................................ 0424 00-3
Index-5 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Discharge Tubes and Hoses

M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0425 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0425 00-1
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0426 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0426 00-2
Front Bilge Pump and/or Light Does Not Operate . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0084 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0424 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0424 00-2
Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0424 00-2
Switch
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0261 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0261 00-2
Blackout Headlights
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0275 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0275 00-1
Blackout Marker Light

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0280 00-2, 0506 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0280 00-1, 0506 00-2
Blackout Stoplight-Tailight
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0507 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0507 00-1
Brake
Control Linkage (M548A3)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . . . . .. . .. . .. . .. . .. . .. . 0347 00-2
Inspection-Acceptance and Rejection Criteria . . .. . .. . .. . .. . . . . .. . .. . .. . .. . .. . .. . 0348 00-4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . . . . .. . .. . .. . .. . .. . .. . 0348 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . . . . .. . .. . .. . .. . .. . .. . 0348 00-2
Differential (M548A1)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0341 00-1
M548A3
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0314 00-1
Parking (M548A3)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0345 00-1
Control Lever/Cable Assembly
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0346 00-1, 0346 00-4
Pivot Steering (M548A1)
Brake Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0373 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0373 00-1
Brake Lining
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0375 00-1
Hoses, Tubes, Fittings
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0372 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0372 00-1
Change 1 Index-6
TM 9-2350-247-20-3
INDEX, cont’d
Transmission (M548A3)
Check With Torque Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0313 00-2
Inspection of Installed Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0313 00-1
Breather
Differential, (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0338 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0338 00-1
Bulkhead Protector
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0487 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0487 00-1
C
Cab
Cover and Frames
Installation . . . . . . . . . . .................................................. 0418 00-5
Removal . . . . . . . . . . . . .................................................. 0418 00-2
Cover, Fiberglass
Installation . . . . . . . . . . .................................................. 0456 00-2
Removal . . . . . . . . . . . . .................................................. 0456 00-1
Dome Light
Installation . . . . . . . . . . .................................................. 0279 00-2
Removal . . . . . . . . . . . . .................................................. 0279 00-1
Door Handles and Linkage
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-8
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-5
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-2
Door Seal
Clean, Inspect, and Repair ................................................. 0388 00-1
Installation . . . . . . . . . . .................................................. 0388 00-2
Removal . . . . . . . . . . . . .................................................. 0388 00-1
Lower
Insulation
Installation . . . . . . . . .................................................. 0459 00-2
Removal . . . . . . . . . . .................................................. 0459 00-1
M548A1
Center Floor Plates
Installation . . . . . . . . .................................................. 0394 00-2
Removal . . . . . . . . . . .................................................. 0394 00-1
Left Floor Plate
Installation . . . . . . . . .................................................. 0394 00-3
Removal . . . . . . . . . . .................................................. 0394 00-2
Throttle Floor Plate
Installation . . . . . . . . .................................................. 0394 00-4
Removal . . . . . . . . . . .................................................. 0394 00-3
Index-7 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
M548A3
Floor Plates, Door and Seat Support
Installation . . . . . . . . . . . . . . . ........................................... 0395 00-5
Removal . . . . . . . . . . . . . . . . . ........................................... 0395 00-2
Personnel Seats
Installation . . . . . . . . . . . . . . . . . ........................................... 0398 00-5
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0398 00-2
Windows
Installation . . . . . . . . . . . . . . . . . ........................................... 0458 00-2
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0458 00-1
Caliber .50 Machine Gun Mount Kit

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-4
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-1
Carbon Dioxide (CO2) Cylinder, Fire Extinguisher

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0526 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0526 00-2
Cargo
Cover, Insulated
Installation . ........................................................... 0466 00-3
Removal . . . ........................................................... 0466 00-2
Door
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-8
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-5
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-2
Door Insulation
Installation . ........................................................... 0469 00-2
Removal . . . ........................................................... 0469 00-1
Door Seals
Installation . ........................................................... 0403 00-3
Removal . . . ........................................................... 0403 00-2
Cargo Area Heater

Fuel Lines, Fittings, and Shields
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0463 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0463 00-1
Fuel Pump
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0464 00-1
Heater and Control Box Mounting
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 00-2
Heater Control Box
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0472 00-5
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0472 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0472 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0472 00-1
Replace/Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0472 00-1
Change 1 Index-8
TM 9-2350-247-20-3
INDEX, cont’d
Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0465 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0465 00-2
Cargo Compartment
Cover
Installation . . .......................................................... 0417 00-4
Removal . . . . .......................................................... 0417 00-2
Floor Plates
Installation . . .......................................................... 0393 00-2
Removal . . . . .......................................................... 0393 00-1
Center Seat Panel (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0384 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0384 00-2
Center Seat Support (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0396 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0396 00-2
Chain, Winch (M548A1)

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-2
Charging System
100 Amp Charging System Malfunctions (M548A1) . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . 0023 00-1
100 Amp Engine Charging System Schematic (M548A1) . . . . . .. . .. . .. . .. . .. . .. . .. . .. . 0029 00-1
200 Amp Charging System Operation Check (M548A3) . . . . . .. . .. . .. . .. . .. . .. . .. . .. . 0024 00-1
200 Amp Engine Charging System Schematic (M548A3) . . . . . .. . .. . .. . .. . .. . .. . .. . .. . 0030 00-1
200 Amp Full Field Charge Troubleshooting (M548A3) . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . 0026 00-1
200 Amp No Charge/Regulation Troubleshooting (M548A3) . . .. . .. . .. . .. . .. . .. . .. . .. . 0025 00-1
200 Amp Over Voltage Troubleshooting (M548A3) . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . 0027 00-1
Connect/Disconnect 200 Amp Generator Test Kit (M548A3) . . .. . .. . .. . .. . .. . .. . .. . .. . 0028 00-1
Check Valve
Air Box Drain (M548A3)
Installtion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0136 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0136 00-1
Circuit Breaker
Bilge Bump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0268 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0268 00-1
Electric Fuel Pump (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0272 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0272 00-1
Generator-Regulator
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0267 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0267 00-1
Index-9 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Circuit Breaker and Relay

NBC (M548A3)
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0530 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0530 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0530 00-1
Clutch
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0374 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0374 00-1
Common Tools, Supplements, and Fixtures List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0541 00-1
Compartment Heater Assembly , Vehicle (M548A3)

Fuel Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0430 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0430 00-1
Compartment Heater, Vehicle

Control Box
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0431 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0431 00-2
Fuel pump
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0429 00-2
M548A1
Controls Cover
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0450 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0450 00-1
Exhaust Pipes Guard
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0479 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0479 00-2
Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0451 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0451 00-2
M548A1 (Kit I)
Air Ducts and Hoses
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0452 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0452 00-2
Exhaust Guard
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0455 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0455 00-2
Fuel Hoses/Tubes/Fittings
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0444 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0444 00-1
Fuel Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0448 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0448 00-1
Heater Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0446 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0446 00-2
Change 1 Index-10
TM 9-2350-247-20-3
INDEX, cont’d
M548A3
Air Inlet Ducts
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0438 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0438 00-2
Defroster Fan Toggle Switches/Identification Plate
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0433 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0433 00-1
Defroster Fan Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0434 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0434 00-2
Defroster, Hoses, and Fans
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0432 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0432 00-2
Exhaust Metal Hose Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0437 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0437 00-2
Fuel Hoses to Fuel /Separator Filter
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0439 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0439 00-2
Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0435 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0435 00-2
Service/Repair/Adjust . . . . . . . . . . . . . . . . . . . . . . ................................ 0427 00-1
Compressor
Air Brake (M548A1)
Installation . . . . . . . . . . . . . . . . . . . ......................................... 0489 00-4
Removal . . . . . . . . . . . . . . . . . . . . . ......................................... 0489 00-2
Drive Belt Guard, Air Brake (M548A1)
Installation . . . . . . . . . . . . . . . . . . . ......................................... 0497 00-2
Removal . . . . . . . . . . . . . . . . . . . . . ......................................... 0497 00-1
Drive Pulley/Belts, Air Brake (M548A1)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0498 00-1
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0498 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0499 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0499 00-1
Coolant Heater, Engine

Control Box
Installation . . . . . . ...................................................... 0474 00-2
Removal . . . . . . . . ...................................................... 0474 00-1
Coolant Pump
Installation . . . . . . ...................................................... 0478 00-2
Removal . . . . . . . . ...................................................... 0478 00-1
Fuel Pump/Fuel Lines
Installation . . . . . . ...................................................... 0475 00-3
Removal . . . . . . . . ...................................................... 0475 00-1
Installation . . . . . . . . ...................................................... 0477 00-3
M548A1
Exhaust Pipes Guard
Installation . . . . ...................................................... 0479 00-3
Removal . . . . . . ...................................................... 0479 00-2
Index-11 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Exhaust System
Installation . ......................................................... 0480 00-3
Removal . . . ......................................................... 0480 00-2
M548A3
Exhaust System
Installation . ......................................................... 0481 00-2
Removal . . . ......................................................... 0481 00-1
Removal . . . . . . . ......................................................... 0477 00-1
Wiring Harness
Cleaning . . . . . ......................................................... 0473 00-2
Installation . . . ......................................................... 0473 00-3
Removal . . . . . ......................................................... 0473 00-1
Coolant Pump
M548A1
Drive Belts/Idler Pulley
Clean, Inspect, and Repair . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0223 00-1
Installation . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0223 00-2
Removal . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0223 00-1
Installation . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0221 00-2
Removal . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0221 00-1
M548A3
Cleaning . . . . . . . . . . . . . . . . .............................................. 0222 00-2
Drive Belts
Inspection . . . . . . . . . . . . . .............................................. 0224 00-2
Installation . . . . . . . . . . . . .............................................. 0224 00-2
Removal . . . . . . . . . . . . . . .............................................. 0224 00-1
Idler Pulley/Adjusting Bracket
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0225 00-4
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0225 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0225 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0225 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0222 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0222 00-1
Coolant Temerature Gauge

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0266 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0266 00-1
Coolant Temperature Transmitter

M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0283 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0283 00-1
M548A3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0284 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0284 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . . . . . . . .. . .. . .. . .. . .. . 0284 00-2
Change 1 Index-12
TM 9-2350-247-20-3
INDEX, cont’d
Coolant Tubes/Hoses/Fittings (M548A3)

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0220 00-7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0220 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0220 00-2
Cooling Fan
Drive Belt
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0226 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0226 00-1
M548A3
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-4
Inspection-Acceptance and Rejection Criteria . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-1
M548A1
Drive Belt Idler Adjusting Linkage
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0230 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0230 00-1
Drive Belt Idler Pulley
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0228 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0228 00-1
Drive Shaft Lubrication Hose, Fittings, and Bearings
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0237 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0237 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0235 00-3
Jackshaft Pulleys
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0231 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0231 00-1
Pulley
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0234 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0234 00-1
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0235 00-1
M548A3
Drain Cap and Sight Gauge
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0239 00-1
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0239 00-1
Drive Housing/Shaft
Clean and Inspect . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0238 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0238 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0238 00-1
Idler Arm
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0232 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0232 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0232 00-1
Idler Arm Support
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0233 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0233 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0233 00-2
Index-13 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Idler Pulley
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0229 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0229 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0229 00-1
Cooling Fan/Pulley (M548A3)

Inspection-Rejection and Acceptance Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0236 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0236 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0236 00-2
Cooling System
M548A1
Drain . . . ............................................................. 0213 00-1
Fill . . . . . ............................................................. 0212 00-1
M548A3
Drain . . . ............................................................. 0214 00-2
Fill . . . . . ............................................................. 0214 00-3
Corrosion Prevention and Control (CPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0001 00-1
Cover
Cab and Frame
Installation . . . . . . . . . . . . ................................................ 0418 00-5
Removal . . . . . . . . . . . . . . ................................................ 0418 00-2
Cab, Fiberglass
Installation . . . . . . . . . . . . ................................................ 0456 00-2
Removal . . . . . . . . . . . . . . ................................................ 0456 00-1
Cargo Compartment
Installation . . . . . . . . . . . . ................................................ 0417 00-4
Removal . . . . . . . . . . . . . . ................................................ 0417 00-2
Cargo, Insulated
Installation . . . . . . . . . . . . ................................................ 0466 00-3
Removal . . . . . . . . . . . . . . ................................................ 0466 00-2
Escape Hatch
Installation . . . . . . . . . . . . ................................................ 0467 00-2
Removal . . . . . . . . . . . . . . ................................................ 0467 00-1
Floor Plate
Installation . . . . . . . . . . . . ................................................ 0470 00-2
Removal . . . . . . . . . . . . . . ................................................ 0470 00-1
Machine Gun Hatch, Fiberglass
Installation . . . . . . . . . . . . ................................................ 0457 00-2
Removal . . . . . . . . . . . . . . ................................................ 0457 00-1
Personnel Seat
Installation . . . . . . . . . . . . ................................................ 0471 00-2
Removal . . . . . . . . . . . . . . ................................................ 0471 00-1
Seat, Cloth
Installation . . . . . . . . . . . . ................................................ 0460 00-3
Removal . . . . . . . . . . . . . . ................................................ 0460 00-2
Windows, Insulated
Installation . . . . . . . . . . . . ................................................ 0468 00-2
Removal . . . . . . . . . . . . . . ................................................ 0468 00-1
Change 1 Index-14
TM 9-2350-247-20-3
INDEX, cont’d
Crankcase Breather Collector Can

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0134 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0134 00-1
D
Data Plate, Marker, and Decal Chart
Locations
M548A1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0441 00-1
M548A3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0442 00-1
Decals
Replace ................................................................ 0440 00-4
Decontamination Brush Guard and Backing Plate, M13

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0401 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0401 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0401 00-2
Destruction of Army Materiel to Prevent Enemy Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0001 00-1
Brakes
Adjustment . . . . . . ...................................................... 0341 00-1
Breather
Installation . . . . . . ...................................................... 0338 00-2
Removal . . . . . . . . ...................................................... 0338 00-1
Gasket
Installation . . . . . . ...................................................... 0344 00-3
Removal . . . . . . . . ...................................................... 0344 00-2
Hoses and Fittings
Installation . . . . . . ...................................................... 0340 00-7
Removal . . . . . . . . ...................................................... 0340 00-2
Mounts
Installation . . . . . . ...................................................... 0342 00-4
Removal . . . . . . . . ...................................................... 0342 00-2
Oil Filter and Element
Installation . . . . . . ...................................................... 0337 00-3
Removal . . . . . . . . ...................................................... 0337 00-2
Oil Level Gauge Rod
Installation . . . . . . ...................................................... 0339 00-2
Removal . . . . . . . . ...................................................... 0339 00-1
Oil Pump
Installation . . . . . . ...................................................... 0336 00-3
Removal . . . . . . . . ...................................................... 0336 00-2
Switch Lead
Installation . . . . . . ...................................................... 0343 00-2
Removal . . . . . . . . ...................................................... 0343 00-1
Differential Oil High Temperature Thermostatic Switch (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0285 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0285 00-1
Index-15 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Differential Pressure Switch and Bypass Plug (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0324 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0324 00-1
Disconnect Control
Engine (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0368 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0368 00-1
Dome Light, Cab

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0279 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0279 00-1
Door
Cab
Handles and Linkage
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-8
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-5
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0386 00-2
Seal
Clean, Inspect, and Repair ............................................... 0388 00-1
Installation . . . . . . . . . . ................................................ 0388 00-2
Removal . . . . . . . . . . . . ................................................ 0388 00-1
Windows
Installation . . . . . . . . . . ................................................ 0387 00-4
Removal . . . . . . . . . . . . ................................................ 0387 00-2
Cargo
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-8
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-5
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0402 00-2
Seals, Cargo
Installation . . . . . . . . . . . . ................................................ 0403 00-3
Removal . . . . . . . . . . . . . . ................................................ 0403 00-2
Drive Sprocket and Track Assembly

T150 Track
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0357 01-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0357 01-1
Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0357 01-1
Drive Sprocket Wheel Assembly (T150)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0357 02-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0357 02-1
Drive Sprockets, Cushions, and Carrier Assembly

T130 Track
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0357 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0357 00-1
Change 1 Index-16
TM 9-2350-247-20-3
INDEX, cont’d
Driver’s Seat
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-5
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-2
E
Electric Fuel Pump (M548A3)
Circuit Breakers
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0272 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0272 00-1
Electrical System
Battery/Generator Indicator Malfuntions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0052 00-1
Blackout Drive Light Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035 00-1
Blackout Marker Light(s) and/or Taillight(s) Do Not Operate . . . . . . . . . . . . . . . . . . . . . . . . . . 0040 00-1
Blackout Stoplight Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039 00-1
Coolant Temperature Gauge Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0053 00-1
Dome Light Works Improperly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0048 00-1
Electrical System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0064 00-1
Fuel Level Indicator Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0050 00-1
Hi Temp Diff Oil Indicator Comes On (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0031 00-1
Hi Temp Diff Oil Indicator Comes On (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0033 00-1
Hi Temp Diff Oil Indicator Malfunctions (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0058 00-1
Hi Temp Trans Oil Indicator Comes On (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0032 00-1
Hi Temp Trans Oil Indicator Malfunctions (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0056 00-1
Hi Temp Trans Oil Indicator Malfunctions (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0057 00-1
High Beam Indicator Light Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0051 00-1
Horn Does Not Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0044 00-1
Infrared Headlights(s) Do Not Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 00-1
Instrument Panel Illumination Lights Malfunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0045 00-1
Instrument Panel Indicators Schematic (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0061 00-1
Instrument Panel Indicators Schematic (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0062 00-1
Lo Press Engine Oil Indicator Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0054 00-1
Low Press Engine Oil Indicator Fails To Go Off After Engine Starts . . . . . . . . . . . . . . . . . . . . . 0046 00-1
Master Switch On Indicator Does Not Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0049 00-1
No Exterior Lights Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0034 00-1
Service and/or Blackout Stoplights Malfunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0038 00-1
Service Stoplight Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042 00-1
Service Taillight Does Not Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0041 00-1
Sevice Headlights Do Not Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0036 00-1
Trailer Lights Do Not Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0043 00-1
Trans Low Oil Press Indicator Comes On (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0047 00-1
Trans Low Oil Press Indicator Malfunctions (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0055 00-1
Trans Oil Hi Diff Press Indicator Malfunctions (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0059 00-1
Windshield Wiper Does Not Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0060 00-1
Index-17 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Engine
Air Box Heater System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0021 00-1
Coolant Heater
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0477 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0477 00-1
Coolant Heater Control Box
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0474 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0474 00-1
Coolant Heater Coolant Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0478 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0478 00-1
Coolant Heater Exhaust Pipes Guard (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0479 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0479 00-2
Coolant Heater Exhaust System
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0480 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0480 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0481 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0481 00-1
Coolant Heater Fuel Pump/Fuel Lines
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0475 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0475 00-1
Coolant Heater Wiring Harness
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0473 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0473 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0473 00-1
Coolant Pump
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0221 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0221 00-1
M548A3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0222 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0222 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0222 00-1
Coolant Pump Drive Belts (M548A3)
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0224 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0224 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0224 00-1
Coolant Pump Drive Belts and Idler Pulley (M548A1)
Clean, Inspect, and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0223 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0223 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0223 00-1
Coolant Temperature Transmitter
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0283 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0283 00-1
M548A3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0284 00-2
Inspection-Acceptance and Rejection Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0284 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0284 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0284 00-2
Change 1 Index-18
TM 9-2350-247-20-3
INDEX, cont’d
Crankcase Breather Hose

Installation . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0137 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0137 00-1
Cranks but Will Not Start . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0014 00-1
Cranks but Will Not Start Below 40 Degrees . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0015 00-1
Cranks Slowly (M548A1) . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0012 00-1
Cranks slowly (M548A3) . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0013 00-1
Disconnect Control (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0368 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0368 00-1
Does Not Crank (M548A1) . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0010 00-1
Does Not Crank (M548A3) . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0011 00-1
Exaust Pipe Guard (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0208 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0208 00-1
Fuel Pump
Flow Test . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0147 00-1
Fuel Pump (M548A1)
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0149 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0149 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0149 00-2
Fuel Pump (M548A3)
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0150 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0150 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0150 00-1
Fuel System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0018 00-1
Governor Throttle Arm (M548A1)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0198 00-2
Ground Lead (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0300 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0300 00-2
Low Oil Pressure Transmitter (M548A3)
Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-2
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-2
Oil Filler Cap and Tube
Installation . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0140 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0140 00-2
Oil Filter Assembly
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . ..................................... 0145 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0145 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . ..................................... 0146 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0146 00-2
Oil Filter Element
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . ..................................... 0143 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0143 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . ..................................... 0144 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ..................................... 0144 00-2
Index-19 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Oil Filter Element Hoses and Fittings (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0142 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0142 00-2
Oil Filter Hoses (M548A1)
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0141 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0141 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0141 00-2
Oil Gauge Rod and Tube
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0138 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0138 00-1
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0139 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0139 00-2
Oil Low Pressure Switch (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0281 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0281 00-1
Overheats (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0007 00-1
Overheats (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0008 00-1
Power Train/Steering/Brakes/Gear Selection/Throttle Diagrams . . . . . . . . . . . . . . . . . . . . . . . . 0022 00-1
Runs Rough, Stalls, or Does Not Put Out Full Power (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . 0016 00-1
Runs Rough, Stalls, or Does Not Put Out Full Power (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . 0017 00-1
Starting System Schematic (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0019 00-1
Starting System Schematic (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0020 00-1
Thermostat (M548A1)
Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0218 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0218 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0218 00-2
Will Not Reach Operating Temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0009 00-1
Equipment Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0002 00-1

Location and Description of Major Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0002 00-1
Escape Hatch Cover

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0467 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0467 00-1
Exhaust Ducts (M548A3)

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0211 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0211 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0211 00-1
Exhaust Muffler
M548A1
Installation ............................................................ 0206 00-2
Removal . ............................................................. 0206 00-1
M548A3
Installation ............................................................ 0207 00-2
Removal . ............................................................. 0207 00-1
Change 1 Index-20
TM 9-2350-247-20-3
INDEX, cont’d
Exhaust Pipe
M548A1
Installation . . . . . ....................................................... 0209 00-3
Removal . . . . . . . ....................................................... 0209 00-2
M548A3
Inspect and Repair ....................................................... 0210 00-2
Installation . . . . . ....................................................... 0210 00-3
Removal . . . . . . . ....................................................... 0210 00-2
Expendable/Durable Supplies and Materials List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0542 00-1
F
Fan, Cooling
Drive Belt
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0226 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0226 00-1
M548A3
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-4
Inspection-Acceptance and Rejection Criteria . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. ....... 0227 00-1
M548A1
Drive Belt Idler Adjusting Linkage
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0230 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0230 00-1
Drive Belt Idler Pulley
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0228 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0228 00-1
Drive Shaft Lubrication Hose, Fittings, and Bearings
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0237 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0237 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0235 00-3
Jackshaft Pulleys
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0231 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0231 00-1
Pulley
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0234 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0234 00-1
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0235 00-1
M548A3
Drain Cap and Sight Gauge
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0239 00-1
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0239 00-1
Drive Housing/Shaft
Clean and Inspect . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0238 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0238 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0238 00-1
Index-21 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Idler Arm
Inspection . . . ........................................................ 0232 00-2
Installation . . ........................................................ 0232 00-2
Removal . . . . ........................................................ 0232 00-1
Idler Arm Support
Inspection . . . ........................................................ 0233 00-2
Installation . . ........................................................ 0233 00-3
Removal . . . . ........................................................ 0233 00-2
Idler Pulley
Inspection . . . ........................................................ 0229 00-2
Installation . . ........................................................ 0229 00-2
Removal . . . . ........................................................ 0229 00-1
Fan, Cooling and Pulley (M548A3)

Inspection-Acceptance and Rejection Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0236 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0236 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0236 00-2
Filtered Air Hose (M548A3) NBC

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0537 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0537 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0537 00-2
Final Drive
Gauge Rod
Installation . . . . . . . . . . . . . . . . . . . ......................................... 0328 00-2
Installation . . . . . . . . . . . . . . . . . . . . . ......................................... 0326 00-3
M548A1
Left Shaft
Installation . . . . . . . . . . . . . . . . . ......................................... 0333 00-2
Removal . . . . . . . . . . . . . . . . . . . ......................................... 0333 00-1
Right Shaft
Installation . . . . . . . . . . . . . . . . . ......................................... 0334 00-3
Removal . . . . . . . . . . . . . . . . . . . ......................................... 0334 00-2
M548A3
Shafts
Installation . . . . . . . . . . . . . . . . . ......................................... 0335 00-3
Removal . . . . . . . . . . . . . . . . . . . ......................................... 0335 00-2
Pinion Oil Seal
Installation . . . . . . . . . . . . . . . . . . . ......................................... 0327 00-2
Removal . . . . . . . . . . . . . . . . . . . . . ......................................... 0327 00-1
Removal . . . . . . . . . . . . . . . . . . . . . . . ......................................... 0326 00-2
Vent, Filler Tube, and Fitting (Left side)
Installation . . . . . . . . . . . . . . . . . . . ......................................... 0330 00-3
Removal . . . . . . . . . . . . . . . . . . . . . ......................................... 0330 00-2
Vent, Filler Tube, and Fitting (Right side)
Installation . . . . . . . . . . . . . . . . . . . ......................................... 0329 00-3
Removal . . . . . . . . . . . . . . . . . . . . . ......................................... 0329 00-2
Change 1 Index-22
TM 9-2350-247-20-3
INDEX, cont’d
Fire Extinguisher
Carbon Dioxide (CO2) Cylinder
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0526 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0526 00-2
Fyr-Fyter Conrol Valve
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0527 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0527 00-2
Nozzles, Tubes, and Fittings
New Configuration
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0524 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0524 00-1
Old Configuration
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0525 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0525 00-1
Portable Fire Extinguisher Panel Assembly (M548A3)
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-3
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-2
Walter Kidde Conrol Valve
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0528 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................... 0528 00-2
Fixtures, Common Tools, and Supplements List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0541 00-1
Flasher
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0509 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0509 00-1
Floor Plates
Cargo Compartment
Installation . . . . . . . . .................................................... 0393 00-2
Removal . . . . . . . . . . .................................................... 0393 00-1
Covers
Installation . . . . . . . . .................................................... 0470 00-2
Removal . . . . . . . . . . .................................................... 0470 00-1
M548A1
Installation
Center Floor Plates . .................................................... 0394 00-2
Left Floor Plate . . . .................................................... 0394 00-3
Throttle Floor Plate .................................................... 0394 00-4
Removal
Center Floor Plates . .................................................... 0394 00-1
Left Floor Plate . . . .................................................... 0394 00-2
Throttle Floor Plate .................................................... 0394 00-3
M548A3
Door, and Seat Support
Installation . . . . . . .................................................... 0395 00-5
Removal . . . . . . . . .................................................... 0395 00-2
Index-23 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Front Access Cover (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0391 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0391 00-1
Front Step
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0419 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0419 00-1
Fuel Compartment
Access Covers
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0163 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0163 00-1
Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0162 00-2
Expansion Chamber (Sealing)
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0175 00-2
Expansion Tank Vent Tubes, Hoses, and Fittings
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0174 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0174 00-2
Tubes, Hoses, and Fittings (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0166 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0166 00-1
Fuel Control (M548A3)

Shaft/Linkage
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0202 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0202 00-1
Fuel Cutoff
Control Cable Assembly (M548A3)
Adjustment . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0205 00-5
Clean, Inspect, and Repair . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0205 00-2
Installation . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0205 00-3
Removal . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0205 00-1
Hand Control
Adjustment . . . . . . . . . . . . . . . ............................................. 0195 00-1
Installation . . . . . . . . . . . . . . . ............................................. 0194 00-3
Removal . . . . . . . . . . . . . . . . . ............................................. 0194 00-2
Fuel Filler Cap and Strainer

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0164 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0164 00-1
Fuel Filter
Elements
M548A1
Installation .......................................................... 0179 00-2
Removal . ........................................................... 0179 00-1
M548A3
Cleaning . ........................................................... 0178 00-3
Installation .......................................................... 0178 00-4
Removal . ........................................................... 0178 00-2
Change 1 Index-24
TM 9-2350-247-20-3
INDEX, cont’d
Personnel Heater (M548A3)

Cleaning . . . . . . . . . . . . . ................................................. 0436 00-3
Installation . . . . . . . . . . . ................................................. 0436 00-3
Removal . . . . . . . . . . . . . ................................................. 0436 00-2
Primary (M548A1)
Installation . . . . . . . . . . . ................................................. 0176 00-3
Removal . . . . . . . . . . . . . ................................................. 0176 00-2
Secondary (M548A1)
Installation . . . . . . . . . . . ................................................. 0177 00-3
Removal . . . . . . . . . . . . . ................................................. 0177 00-2
Tubes, Hoses, and Fittings
Installation . . . . . . . . . . . ................................................. 0165 00-3
Removal . . . . . . . . . . . . . ................................................. 0165 00-2
Fuel Level
Gauge
Installation . . . . . . . . . . .................................................. 0266 00-2
Removal . . . . . . . . . . . . .................................................. 0266 00-1
Transmitter
Installation . . . . . . . . . . .................................................. 0169 00-3
Removal . . . . . . . . . . . . .................................................. 0169 00-2
Fuel Lines/Fittings
Engine to Bulkhead
M548A1
Installation . . . . ...................................................... 0167 00-4
Removal . . . . . . ...................................................... 0167 00-2
M548A3
Clean and Inspect ...................................................... 0168 00-2
Installation . . . . ...................................................... 0168 00-3
Removal . . . . . . ...................................................... 0168 00-1
Fuel Pump
Electric
Installation . . .......................................................... 0151 00-3
Removal . . . . .......................................................... 0151 00-2
Flow Test . . . . . .......................................................... 0147 00-1
M548A1
Cleaning . . . . .......................................................... 0149 00-2
Installation . . .......................................................... 0149 00-3
Removal . . . . .......................................................... 0149 00-2
M548A3
Cleaning . . . . .......................................................... 0150 00-2
Installation . . .......................................................... 0150 00-2
Removal . . . . .......................................................... 0150 00-1
Wiring Harness
Installation .......................................................... 0302 00-3
Removal . . .......................................................... 0302 00-1
Index-25 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Switch
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0261 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0261 00-2
Vehicle Compartment Heater
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0429 00-2
Fyr-Fyter Control Valve

Fire Extinguisher
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0527 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0527 00-2
G
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0001 00-1
Generator
100 Amp (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0242 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0242 00-1
Drive Belts
M548A1
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0241 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0240 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0240 00-1
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0245 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0245 00-1
Drive Belts Adjusting Linkage
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0243 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0243 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0247 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0247 00-1
Field Switch
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0288 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0288 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0288 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0246 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0246 00-2
Mount
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0244 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0244 00-1
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0248 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0248 00-1
Regulator
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0249 00-2
Change 1 Index-26
TM 9-2350-247-20-3
INDEX, cont’d
Regulator Ground and Lead (M548A3)

Installation . . . . . . . . . . . . . . . . . . .......................................... 0251 00-2
Removal . . . . . . . . . . . . . . . . . . . . .......................................... 0251 00-1
Regulator Mount
M548A1
Installation . . . . . . . . . . . . . . . . .......................................... 0250 00-2
Removal . . . . . . . . . . . . . . . . . . .......................................... 0250 00-1
M548A3
Installation . . . . . . . . . . . . . . . . .......................................... 0252 00-2
Removal . . . . . . . . . . . . . . . . . . .......................................... 0252 00-1
Wiring Harness to Regulator
M548A1
Installation . . . . . . . . . . . . . . . . .......................................... 0295 00-2
Removal . . . . . . . . . . . . . . . . . . .......................................... 0295 00-1
M548A3
Installation . . . . . . . . . . . . . . . . .......................................... 0296 00-3
Removal . . . . . . . . . . . . . . . . . . .......................................... 0296 00-1
Generator-Regulator
Circuit Breaker
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269 00-1
Governor Assembly (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0317 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0317 00-2
Governor, Air Brake (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0490 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0490 00-1
H
Hand Throttle Control
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0192 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0192 00-2
Hand Throttle Control Cable

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0193 00-2
Headlights
Blackout
Installation ............................................................ 0275 00-2
Removal . ............................................................. 0275 00-1
Infrared
Installation ............................................................ 0277 00-3
Removal . ............................................................. 0277 00-1
Service
Installation ............................................................ 0276 00-3
Removal . ............................................................. 0276 00-1
Index-27 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Heater and Adapter (M548A3) NBC

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0532 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0532 00-2
High Beam Indicator Light

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0257 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0257 00-1
High Beam Indicator Light Bulb

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0258 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0258 00-1
Hoist
Material Handling Kit
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0485 00-14
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0485 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0485 00-2
Hoist /Stops/Sling
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-3
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-1
Hook, Winch (M548A1)

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-2
nstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-2
Horn
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0289 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0289 00-1
How To Use Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0005 00-1
Hull
Welding, Repair By
Aluminum Castings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-1
Equipment and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-1
Magnesium Castings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-2
Magnesium Castings, Filing, and Grinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-4
MIG Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-4
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-3
Hull Bottom Access Cover and Drain Cover

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0383 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0383 00-1
Change 1 Index-28
TM 9-2350-247-20-3
INDEX, cont’d
I
Idler Wheel
Arm Assembly
Installation . . . . . . . . .................................................... 0354 00-3
Removal . . . . . . . . . . .................................................... 0354 00-2
Hub/Bearings and Seals
Installation . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0355 00-3
Removal . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0355 00-2
Installation . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0360 00-2
Removal . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0360 00-1
Replace . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0360 00-1
Infrared Headlights
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0277 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0277 00-1
Infrared-Blackout Select Switch

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0263 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0263 00-1
Instrument Panel
Air Box Heater Switch
Installation . . . . . . . . . . . . . ............................................... 0260 00-3
Removal . . . . . . . . . . . . . . . ............................................... 0260 00-2
Air Brake (M548A1)
Installation . . . . . . . . . . . . . ............................................... 0501 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0501 00-1
Battery-Generator Gauge
Installation . . . . . . . . . . . . . ............................................... 0266 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0266 00-1
Circuit Breaker
Installation . . . . . . . . . . . . . ............................................... 0267 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0267 00-1
Coolant Temperature Gauge
Installation . . . . . . . . . . . . . ............................................... 0266 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0266 00-1
Fuel Level Gauge
Installation . . . . . . . . . . . . . ............................................... 0266 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0266 00-1
High Beam Indicator Light
Installation . . . . . . . . . . . . . ............................................... 0257 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0257 00-1
High Beam Indicator Light Bulb
Installation . . . . . . . . . . . . . ............................................... 0258 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0258 00-1
Horn and Start Switches
Installation . . . . . . . . . . . . . ............................................... 0259 00-2
Removal . . . . . . . . . . . . . . . ............................................... 0259 00-1
Index-29 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Infrared-Blackout Selector Switch

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-3, 0263 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-2, 0263 00-1
Light Switch
Installation . . . . . . . . . . . . . . . . . ........................................... 0262 00-2
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0262 00-1
Panel Lights
Installation . . . . . . . . . . . . . . . . . ........................................... 0264 00-4
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0264 00-2
Partial
Installation . . . . . . . . . . . . . . . . . ........................................... 0256 00-3
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0256 00-1
Transmission-Differential Test Switch
Installation . . . . . . . . . . . . . . . . . ........................................... 0260 00-3
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0260 00-2
Utility Outlet
Installation . . . . . . . . . . . . . . . . . ........................................... 0265 00-2
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0265 00-1
Windshield Wiper Switch
Installation . . . . . . . . . . . . . . . . . ........................................... 0260 00-3
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0260 00-2
Insulation, Lower Cab

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 00-1
L
Lifting Eye
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0382 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0382 00-1
Light
Blackout Marker Light
Installation . . . . . . . . . . .................................................. 0506 00-3
Removal . . . . . . . . . . . . .................................................. 0506 00-2
Blackout Stoplight-Taillight
Installation . . . . . . . . . . .................................................. 0507 00-2
Removal . . . . . . . . . . . . .................................................. 0507 00-1
Flasher
Installation . . . . . . . . . . .................................................. 0509 00-2
Removal . . . . . . . . . . . . .................................................. 0509 00-1
Reflector
Installation . . . . . . . . . . .................................................. 0510 00-2
Removal . . . . . . . . . . . . .................................................. 0510 00-1
Switch
Installation . . . . . . . . . . .................................................. 0262 00-2
Removal . . . . . . . . . . . . .................................................. 0262 00-1
Turn Signal
Installation . . . . . . . . . . .................................................. 0505 00-3
Removal . . . . . . . . . . . . .................................................. 0505 00-1
Turn Signal Control Mount
Installation . . . . . . . . . . .................................................. 0508 00-2
Removal . . . . . . . . . . . . .................................................. 0508 00-1
Change 1 Index-30
TM 9-2350-247-20-3
INDEX, cont’d
List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0001 00-1
Low Oil Pressure Transmitter (M548A3)
Clean . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-2

Inspection .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-3
Installation . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-3
Removal . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0282 00-2
M
M13 Decontamination Brush Guard and Backing Plate
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0401 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0401 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0401 00-2
M18 Filter (M548A3) NBC

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0536 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0536 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0536 00-1
M1A1-19 Particulate Filter Unit (M548A3) NBC

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0535 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0535 00-2
M1A1-19 Precleaner Assembly and Frame (M548A3) NBC

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0534 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0534 00-2
M66 Ring Mount Kit

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0514 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0514 00-2
Machine Gun Hatch Fiberglass Cover

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0457 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0457 00-1
Machine Gun Mount Kit

7.62 mm
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0515 00-3
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0515 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0515 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0515 00-1
Caliber .50
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-4
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0513 00-1
Maintenance Allocation Chart (MAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0540 00-1
Index-31 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Maintenance Forms, Records, and Reports ......................................... 0001 00-1
Malfunction/Symptom Index WP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0006 00-1
Manifold (M548A3) NBC

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0533 00-5
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0533 00-4
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0533 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0533 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0533 00-2
Master Cylinder (M548A1)

Pivot Steering Brake
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0371 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0371 00-2
Master Switch (M548A3)

To Bus Bar Electrical lead
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0270 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0270 00-2
Master Switch Assembly

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0271 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0271 00-2

Beam/Beam Supports/Stops
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0483 00-2
Disasembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0483 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0483 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0483 00-1
Bulkhead Protector
Installation . . . . . . . . . . . ................................................. 0487 00-2
Removal . . . . . . . . . . . . . ................................................. 0487 00-1
Hoist
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0485 00-14
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0485 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0485 00-2
Hoist/Stops/Sling
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-3
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0484 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0482 00-1
Personnel Seats/Safety Belt
Installation . . . . . . . . . . . ................................................. 0486 00-2
Removal . . . . . . . . . . . . . ................................................. 0486 00-1
Removal . . . . . . . . . . . . . . . ................................................. 0482 00-1
Rifle Rack
Installation . . . . . . . . . . . ................................................. 0488 00-2
Removal . . . . . . . . . . . . . ................................................. 0488 00-1
Change 1 Index-32
TM 9-2350-247-20-3
INDEX, cont’d
Materials and Expendable Supplies List ........................................... 0542 00-1
Motor
Windshield Wiper
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0420 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0420 00-1
Multiple Pin and Socket Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0129 00-1
N
NBC System (M548A3)
Circuit Breaker and Relay
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0530 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0530 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0530 00-1
Filtered Air Hose
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0537 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0537 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0537 00-2
Heater and Adapter
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0532 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0532 00-2
Low Air Flow At All Outlets . . . . . . . . . . . . . . . . . . . .............................. 0106 00-1
M18 Filter
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0536 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0536 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0536 00-1
M1A1-19 Particulate Filter Unit
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0535 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0535 00-2
M1A1-19 Precleaner Assembly and Frame
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0534 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0534 00-2
M3 Heater Does Not Work . . . . . . . . . . . . . . . . . . . . . .............................. 0104 00-1
Manifold
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0533 00-5
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0533 00-4
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0533 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0533 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0533 00-2
No Air Flow At One or More Outlets . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0105 00-1
Orifice Connector Assembly and Bracket
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0538 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0538 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0538 00-2
Particulate Precleaner Motor Does Not Work . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0103 00-1
Wiring Harness from Battery Compartment to Manifold
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0531 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................. 0531 00-2
Index-33 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Neutral Start Switch

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0308 00-4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0308 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0308 00-2
Nomenclature Cross-Reference List .............................................. 0001 00-1
O
Oil Filler Cap and Tube
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0140 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0140 00-2
Oil Filter (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0143 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0143 00-2
Oil Filter and Element

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0337 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0337 00-2
Oil Filter Assembly

M548A1
Installation . ........................................................... 0145 00-3
Removal . . . ........................................................... 0145 00-2
M548A3
Installation . ........................................................... 0146 00-3
Removal . . . ........................................................... 0146 00-2
Oil Filter Element

Hoses and Fittings (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0142 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0142 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0144 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0144 00-2
Transmission
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0320 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0320 00-1
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0321 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0321 00-2
Change 1 Index-34
TM 9-2350-247-20-3
INDEX, cont’d
Oil Gauge Rod and Tube

M548A1
Installation . . . . . ....................................................... 0138 00-2
Removal . . . . . . . ....................................................... 0138 00-1
M548A3
Installation . . . . . ....................................................... 0139 00-3
Removal . . . . . . . ....................................................... 0139 00-2
Oil Hoses and Fittings
Air Brake (M548A1)
Installation . . . . . . ...................................................... 0496 00-3
Removal . . . . . . . . ...................................................... 0496 00-2
Installation . . . . . . ...................................................... 0340 00-7
Removal . . . . . . . . ...................................................... 0340 00-2
M548A1
Cleaning . . . . . . . . ...................................................... 0141 00-3
Installation . . . . . . ...................................................... 0141 00-4
Removal . . . . . . . . ...................................................... 0141 00-2
Oil Level Gauge Rod

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0339 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0339 00-1
Oil Level Gauge Rod and Filler Neck (M548A1)

Transfer Gearcase
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0331 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0331 00-2
Oil Low Pressure Switch (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0281 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0281 00-1
Oil Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0336 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0336 00-2
Oil Sampling Valve, Guard, and Pressure Switch (M548A3)

Transmission
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0323 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0323 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0323 00-1
Oil Sampling Valve, Hose and Bracket (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0322 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0322 00-2
Orifice Connector Assembly and Bracket (M548A3) NBC

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0538 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0538 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0538 00-2
Index-35 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
P
Panel Lights
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0264 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0264 00-2
Parking Brake (M548A3)

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0345 00-1
Control Lever/Cable Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0346 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0346 00-1
Personnel Heater
Fuel Filter (M548A3)
Cleaning . . . . . . . ....................................................... 0436 00-3
Installation . . . . . ....................................................... 0436 00-3
Removal . . . . . . . ....................................................... 0436 00-2
Fuel Pump
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0148 00-2
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0148 00-2
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0148 00-2
Flow Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0148 00-3
Personnel Seat
Cover
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0471 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0471 00-1
Personnel Seat/Safety Belt

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0486 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0486 00-1
Pinion Oil Seal

Final Drive
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0327 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0327 00-1

Brake Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0373 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0373 00-1
Brake Controls/Linkage
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0370 00-1
Brake Hoses, Tubes, Fittings
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0372 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0372 00-1
Brake Lining
Inspection-Acceptance and Rejection Criteria ................................... 0375 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0375 00-1
Clutch Disk
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0374 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0374 00-1
Change 1 Index-36
TM 9-2350-247-20-3
INDEX, cont’d
Pivot Steering Brake (M548A1)

Controls/Linkage
Installation . . . . . . . . . . .................................................. 0369 00-6
Removal . . . . . . . . . . . . .................................................. 0369 00-2
Master Cylinder
Installation . . . . . . . . . . .................................................. 0371 00-3
Removal . . . . . . . . . . . . .................................................. 0371 00-2
Portable Fire Extinguisher Panel Assembly (M548A3)

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-3
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0529 00-2
Power Plant
M548A1
Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . . . . .. . .. . .. . .. . . . . . . . . . . . . . . . . 0132 00-1
Inspection-Acceptance and Rejection Criteria . . .. . . . . .. . .. . .. . .. . . . . . . . . . . . . . . . 0130 00-15
Installation . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . . . . .. . .. . .. . .. . . . . . . . . . . . . . . . 0130 00-15
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . . . . .. . .. . .. . .. . . . . . . . . . . . . . . . . 0130 00-2
M548A3
Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0133 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0131 00-9
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0131 00-1
Right Rear Access Cover Seal
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0389 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0389 00-1
Sling
Periodic Check . . . . . . . . . . . . . . . . . . . . . .................................... 0443 00-1
Preoperative Check . . . . . . . . . . . . . . . . . . .................................... 0443 00-7
Wiring Harness (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0298 00-8
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0298 00-2
Preparation for Storage and Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0001 00-1
Preventive Maintenance Checks and Services (PMCS), Including Lubrication Instructions . . . . . . . 0128 00-1
R
Radiator
Auxiliary Tank (M548A3)
Clean and Inspect . . . . . . . . ............................................... 0217 00-3
Installation . . . . . . . . . . . . . ............................................... 0217 00-4
Removal . . . . . . . . . . . . . . . ............................................... 0217 00-2
Tubes/Hoses/Fittings (M548A1)
Installation . . . . . . . . . . . . . ............................................... 0219 00-8
Removal . . . . . . . . . . . . . . . ............................................... 0219 00-2
Index-37 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Radiator/Seal
M548A1
Installation . . . . . . . . . . .................................................. 0215 00-5
Removal . . . . . . . . . . . . .................................................. 0215 00-2
M548A3
Clean and Inspect . . . . . .................................................. 0216 00-3
Installation . . . . . . . . . . .................................................. 0216 00-4
Removal . . . . . . . . . . . . .................................................. 0216 00-2
Range Selector Control and Linkage (M548A1)

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0316 00-2
Range Selector Linkage (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0315 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0315 00-1
Rear Tiedown Plates

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0378 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0378 00-1
Reflector
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0510 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0510 00-1
Regulator
Adjustment
Adjustment . . . . . . . . . . . . . . . . . . .......................................... 0249 00-2
Mount
M548A1
Installation . . . . . . . . . . . . . . . . .......................................... 0250 00-2
Removal . . . . . . . . . . . . . . . . . . .......................................... 0250 00-1
M548A3
Installation . . . . . . . . . . . . . . . . .......................................... 0252 00-2
Removal . . . . . . . . . . . . . . . . . . .......................................... 0252 00-1
Regulator and Ground Lead (M548A3)
Installation . . . . . . . . . . . . . . . . . . .......................................... 0251 00-2
Removal . . . . . . . . . . . . . . . . . . . . .......................................... 0251 00-1
Reporting of Equipment Improvement Recommendations (EIR) . . . . . . . . . . . . . . . . . . . . . . . . . . 0001 00-1
Reservoir, Air Brake (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0491 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0491 00-1
Change 1 Index-38
TM 9-2350-247-20-3
INDEX, cont’d
Rifle Rack
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0488 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0488 00-1
Right Seat (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0400 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0400 00-1
Ring Mount Kit, M66

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0514 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0514 00-2
Road Wheel
Hub
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0352 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0352 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0352 00-2
Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0352 00-2
Support Arm Bumper Stop/Support
Installation . . . . . . . . . . . . . . . . . . . . . ....................................... 0353 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0353 00-1
Replace . . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0353 00-1
Support Arm, Housing, Bearings, and Seals
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351 00-2
Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0351 00-2
T130 Track
Installation . . . . . . . . . . . . . . . . . . . . . ....................................... 0361 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0361 00-1
T150 Track
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0361 01-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0361 01-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0361 01-1
Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0361 01-1
Rubber Pads and Strips

Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0440 00-6
S
Safety Belts
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0399 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0399 00-2
Safety Valve, Air Brake (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0492 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0492 00-1
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0001 00-1
Index-39 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Seat
Cab Personnel
Installation . . .......................................................... 0398 00-5
Removal . . . . .......................................................... 0398 00-2
Driver’s
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-5
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0397 00-2
Right (M548A1)
Installation . . .......................................................... 0400 00-2
Removal . . . . .......................................................... 0400 00-1
Seat Support (M548A1)

Center
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0396 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0396 00-2
Service Headlights
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0276 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0276 00-1
Service Upon Receipt ........................................................ 0127 00-1
Shaft
M548A1
Left Final drive
Installation . . . . . . . . . . . . . . . . .......................................... 0333 00-2
Removal . . . . . . . . . . . . . . . . . . .......................................... 0333 00-1
Right Final drive
Installation . . . . . . . . . . . . . . . . .......................................... 0334 00-3
Removal . . . . . . . . . . . . . . . . . . .......................................... 0334 00-2
M548A3
Final Drive
Installation . . . . . . . . . . . . . . . . .......................................... 0335 00-3
Removal . . . . . . . . . . . . . . . . . . .......................................... 0335 00-2
Transmission to Differential (M548A1)
Installation . . . . . . . . . . . . . . . . . . .......................................... 0332 00-3
Removal . . . . . . . . . . . . . . . . . . . . .......................................... 0332 00-2
Shift Control (M548A3)

Lamp
Installation . . . . . ....................................................... 0307 00-2
Removal . . . . . . . ....................................................... 0307 00-1
Switch
Installation . . . . . ....................................................... 0309 00-2
Removal . . . . . . . ....................................................... 0309 00-1
Transmission
Installation . . . . . ....................................................... 0306 00-2
Removal . . . . . . . ....................................................... 0306 00-1
Change 1 Index-40
TM 9-2350-247-20-3
INDEX, cont’d
Shock Absorber
Installation . ............................................................. 0379 00-3
Mount
Installation ............................................................ 0381 00-2
Removal . ............................................................. 0381 00-1
Pin
Installation ............................................................ 0380 00-2
Removal . ............................................................. 0380 00-1
Removal . . . ............................................................. 0379 00-1
Sling, Power Plant

Periodic Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0443 00-1
Preoperative Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0443 00-7
Socket Identification, Multiple Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0129 00-1
Speedometer
Cable
Installation . . . . . . . . . ................................................... 0518 00-2
Removal . . . . . . . . . . . ................................................... 0518 00-1
Cable Housing and Adapter
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0517 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0517 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0516 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0516 00-1
Speedometer/Tachometer
Speedometer Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0087 00-1
Tachometer Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0088 00-1
Start Switch
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0259 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0259 00-1
Starter
M548A1
Installation . . . . ........................................................ 0253 00-3
Removal . . . . . . ........................................................ 0253 00-2
M548A3
Clean and Inspect ....................................................... 0254 00-3
Installation . . . . ........................................................ 0254 00-3
Removal . . . . . . ........................................................ 0254 00-2
Relay (M548A3)
Clean and Inspect ....................................................... 0255 00-2
Installation . . . . ........................................................ 0255 00-3
Removal . . . . . . ........................................................ 0255 00-1
Index-41 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
STE/ICE-R
Battery Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0111 00-1
Charging Circuit Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0108 00-1
Engine Will Crank but Will Not Start Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0113 00-1
Engine Will Not Crank Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0112 00-1
Hook Up/Remove STE/ICE-R For Engine RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0115 00-1
Hook Up/Remove STE/ICE-R For Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0114 00-1
Hook Up/Remove STE/ICE-R For Starter Circuit Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0116 00-1
Hook Up/Remove STE/ICE-R Test Set For Test Numbers 72 Thru 75 . . . . . . . . . . . . . . . . . . . . 0117 00-1
Low Oil Pressure Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0110 00-1
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0107 00-1
Starter Circuit Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0109 00-1
Test 01 Display Engine RPM With Next Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0118 00-1
Test 10 Engine RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0119 00-1
Test 13 Power (Percent) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0120 00-1
Test 14 Compression Unbalance (Power Cable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0121 00-1
Test 67 Battery Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0122 00-1
Test 72 Starter Current (First Peak) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0123 00-1
Test 73 Battery Resistance - STE/ICE-R Test 75 Battery Resistance Change (Pack) . . . . . . . . . . 0124 00-1
Test 74 Starter Circuit Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0125 00-1
Test 90 DC Current 0 To 1500 Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0126 00-1
Steering
M548A1
Brake Controls/Linkage
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0370 00-1
Control/Linkage
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0366 00-7
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0366 00-1
Controls
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0367 00-2
Pivot Steering Brake Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0373 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0373 00-1
Pivot Steering Brake Controls/Linkage
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0369 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0369 00-2
Pivot Steering Brake Lining
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0375 00-1
Pivot Steering Brake Master Cylinder
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0371 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0371 00-2
Pivot Steering Clutch Disk
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0374 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0374 00-1
M548A3
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .................................. 0312 00-3
Inspection of Installed Items . . . . . . . . . . . . . . .................................. 0312 00-1
Steering System
Carrier Does Not Move In Any Shift Lever Position (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . 0069 00-1
Carrier Does Not Move In Any Shift Lever Position (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . 0071 00-1
Carrier Does Not Pivot (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072 00-1
Change 1 Index-42
TM 9-2350-247-20-3
INDEX, cont’d
Carrier Does Not Steer (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0075 00-1

Carrier Moves With Transmission In SL (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0074 00-1
Service and/or Parking Brake Will Not Hold Carrier (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . 0076 00-1
Steering/Brakes Malfunction (M548A1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0068 00-1
Transmission Does Not Downshift In 1-4 Position (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . 0078 00-1
Transmission Does Not Hold 1st Position (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0079 00-1
Transmission Does Not Hold 2nd Position (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0080 00-1
Transmission Does Not Hold 3rd Position (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0081 00-1
Transmission Does Not Pivot Steer (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0073 00-1
Transmission Does Not Reverse (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0082 00-1
Transmission System Schematic (M548A3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0070 00-1
Transmission Will Not Upshift or Shifts Erratically In 1-4 Position (M548A3) . . . . . . . . . . . . . 0077 00-1
Steering Wheel (M548A3)

Column/Housing/Shaft
Installation . . . . . . . . . . . . ................................................ 0365 00-4
Removal . . . . . . . . . . . . . . ................................................ 0365 00-2
Linkage
Adjustment . . . . . . . . . . . . ................................................ 0362 00-2
Installation . . . . . . . . . . . . ................................................ 0364 00-3
Removal . . . . . . . . . . . . . . ................................................ 0364 00-1
Quick Release Pin and Bracket
Installation . . . . . . . . . . . . ................................................ 0363 00-2
Removal . . . . . . . . . . . . . . ................................................ 0363 00-1
Stencils
Replace ................................................................ 0440 00-3
Step, Front
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0419 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0419 00-1
Stoplight Switch
Air Brake (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0493 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0493 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0274 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0274 00-1
Stoplight-Taillights
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 00-1
Strainer, Air Brake (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0500 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0500 00-1
Straps
Replace ................................................................ 0440 00-8
Supplements, Fixtures, and Common Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0541 00-1
Index-43 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
T
T150 Track Shoe
Stowage Bracket
Installation . . . . . . . . . . . . ................................................ 0405 01-2
Removal . . . . . . . . . . . . . . ................................................ 0405 01-1
Replace . . . . . . . . . . . . . . . ................................................ 0405 01-1
Tachometer
Cable
M548A1
Installation . . . . . . . . . . ................................................ 0522 00-3
Removal . . . . . . . . . . . . ................................................ 0522 00-1
M548A3
Clean, Inspect, and Repair ............................................... 0523 00-2
Installation . . . . . . . . . . ................................................ 0523 00-3
Removal . . . . . . . . . . . . ................................................ 0523 00-1
Cable Housing and Adapter
M548A1
Installation . . . . . . . . . . ................................................ 0520 00-4
Removal . . . . . . . . . . . . ................................................ 0520 00-2
M548A3
Clean, Inspect, and Repair . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0521 00-2
Installation . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0521 00-3
Removal . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0521 00-1
Installation . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0519 00-2
Removal . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0519 00-1
Tailgate
Controls
Adjustment . . . . . . . ..................................................... 0404 00-4
Installation . . . . . . . ..................................................... 0404 00-3
Removal . . . . . . . . . ..................................................... 0404 00-2
End Seals and Bumpers
Installation . . . . . . . ..................................................... 0405 00-3
Removal . . . . . . . . . ..................................................... 0405 00-2
Theory of Operation ......................................................... 0003 00-1
Thermal Door Windows

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0461 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0461 00-1
Thermostat (M548A1)
Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0218 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0218 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0218 00-2
Throttle Pedal
Control (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0201 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0201 00-1
Change 1 Index-44
TM 9-2350-247-20-3
INDEX, cont’d
Control/Detent (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0196 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0196 00-1
Full Throttle/Idle Positions (M548A1)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0199 00-1
Linkage (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0197 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0197 00-2
Throttle Valve (TV) Modulator (M548A3)

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0204 00-2
Field Operational Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0204 00-5
Throttle Valve Modulator/Lever (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0203 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0203 00-1
Tiedown Plates, Rear

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0378 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0378 00-1
Top Access Cover and Grilles (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0390 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0390 00-1
Torsion Bar
Anchor
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0350 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0350 00-1
Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0350 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0349 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0349 00-1
Tow Start Cable/Cover (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0310 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0310 00-1
Tow Start Control Cable Assembly (M548A3)

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0311 00-1
Towing Eye Pad and Hook

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0376 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0376 00-1
Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0376 00-1
Towing Pintle
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0377 00-2
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0377 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0377 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0377 00-1
Index-45 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Track
T130
Drive Sprockets, Cushions, and Carrier Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0357 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0357 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0358 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . 0358 00-1
Road Wheel
Installation . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0361 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0361 00-1
Track Shoe and Pad Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0359 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0359 00-1
T150
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0358 01-1
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0358 01-1
Track Shoe Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0359 01-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0359 01-1
Track Shoe Pad
Installation . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0359 02-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0359 02-1
Tension Adjuster/Mount
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0356 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................. 0356 00-1
Trailer Wiring Harness

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0301 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0301 00-1
Transfer Gearcase (M548A1)

Mounts
Installation . . . . . . . . . . . . . . . . . ........................................... 0325 00-2
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0325 00-1
Oil Level Gauge Rod and Filler Neck
Installation . . . . . . . . . . . . . . . . . ........................................... 0331 00-3
Removal . . . . . . . . . . . . . . . . . . . ........................................... 0331 00-2
Transmission
Brakes (M548A3)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................ 0314 00-1
Check With Torque Wrench . . . . . . . . . . . . . . . . . . . . ............................ 0313 00-2
Inspection of Installed Items . . . . . . . . . . . . . . . . . . . . ............................ 0313 00-1
Differential Pressure Switch and Bypass Plug (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................ 0324 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................ 0324 00-1
Oil Filter Element
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................ 0320 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................ 0320 00-1
M548A3
Inspection-Acceptance and Rejection Criteria . . . . . ............................ 0321 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................ 0321 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................ 0321 00-2
Change 1 Index-46
TM 9-2350-247-20-3
INDEX, cont’d
Oil High Temperature Switch (M548A3)

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. ....... 0287 00-2
Inspection-Acceptance and Rejection Criteria . . . . . . . . .. . .. . .. . .. . .. . .. . .. ....... 0287 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. ....... 0287 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. ....... 0287 00-1
Oil High Temperature Thermostatic Switch (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0286 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0286 00-1
Oil Hoses and Fittings
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0318 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0318 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0319 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0319 00-1
Oil Level Gauge Rod, Filler Tube, and Adapter (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0305 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0305 00-1
Oil Sampling Valve, Guard, and Pressure Switch (M548A3)
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0323 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0323 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0323 00-1
Oil Sampling Valve, Hose and Bracket (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0322 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0322 00-2
Range Selector Control and Linkage (M548A1)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0316 00-2
Range Selector Linkage (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0315 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0315 00-1
Shaft to Differential (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0332 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0332 00-2
Shift Control (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0306 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0306 00-1
Shift Control Lamp (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0307 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0307 00-1
Shift Control Switch (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0309 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0309 00-1
Shift Control, Neutral Start Switch
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0308 00-4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0308 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0308 00-2
Steering (M548A3)
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0312 00-3
Inspection of Installed Items . . . . . . . . . . . . . . . . . . . . . ........................... 0312 00-1
Vent Tube, Gauge Rod, and Filler Neck (M548A1)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0304 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................... 0304 00-2
Index-47 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Wiring Harness (M548A3)

Inspection-Acceptance and Rejection Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0297 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0297 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0297 00-2
Transmission-Differential Test Switch

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-2
Transverse Beam and Center Seat Panel (M548A1)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0384 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0384 00-2
Transverse Beam Bolted (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0385 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0385 00-1
Turn Signal
Control Mount
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0508 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0508 00-1
Front Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0511 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0511 00-1
In Left or Right Turn Signal Position, Individual Light Does Not Flash . . . . . . . . . . . . . . . . . . . 0067 00-1
Light
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0505 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0505 00-1
Rear Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0512 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0512 00-1
Turn Signal Lamp, Stoplight, or Control Light Does Not Light or Flash When Control Is In Right or Left Turn
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0065 00-1
Turn Signal Lamps and Stoplights Do Not Flash With Control In Hazard Position . . . . . . . . . . . 0066 00-1
U
Utility Outlet
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0265 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0265 00-1
V
Control box
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0431 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0431 00-2
Fuel Pump
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0429 00-2
Change 1 Index-48
TM 9-2350-247-20-3
INDEX, cont’d
M548A1
Controls Cover
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0450 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0450 00-1
Exhaust Pipes Guard
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0479 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0479 00-2
Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0451 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0451 00-2
M548A1 (Kit I)
Air Ducts and Hoses
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0452 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0452 00-2
Exhaust Guard
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0455 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0455 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0444 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0444 00-1
Fuel Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0448 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0448 00-1
Heater Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0446 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0446 00-2
M548A1 (Kit II or III)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0445 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0445 00-1
Fuel Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0449 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0449 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0447 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0447 00-1
M548A1 (Kit II)
Air Ducts/Hoses
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0453 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0453 00-2
M548A1 (Kit III)
Air Ducts/Hoses
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0454 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0454 00-2
M548A3
Air Inlet Ducts
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0438 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0438 00-2
Defroster Fan Toggle Switches/Identification Plate
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0433 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ 0433 00-1
Index-49 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Defroster Fan Wiring Harness

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0434 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0434 00-2
Defroster, Hoses, and Fans
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0432 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0432 00-2
Exhaust Metal Hose Assembly
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0437 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0437 00-2
Fuel Hoses to Fuel/Separator Filter
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0439 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0439 00-2
Wiring Harness
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0435 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0435 00-2
Service/Repair/Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0427 00-1
Vehicle Compartment Heater Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0085 00-1
Vehicle Compartment Heater Assembly (M548A3)

Fuel Pump
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0430 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0430 00-1
Vehicle Compartment Heater Assembly and Mounting Brackets (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0428 00-6
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0428 00-1
Vehivle Identification Plates

Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0440 00-2
W
Walter Kidde Control Valve
Fire Extinguisher
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0528 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0528 00-2
Welding
Hull Repair
Aluminum Castings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-1
Equipment and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-1
Magnesium Castings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-2
Magnesium Castings, Filing, and Grinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-4
MIG Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-4
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0406 00-3
Winch (M548A1)
Cleaning . . . . ............................................................ 0407 00-4
Clutch Lever
Adjustment ............................................................ 0410 00-2
Installation ............................................................ 0410 00-2
Removal . . ............................................................ 0410 00-1
Change 1 Index-50
TM 9-2350-247-20-3
INDEX, cont’d
Drum Brake Shoe

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0408 00-1
Drum Lock Handle
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0411 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0411 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0411 00-1
Drum Safety Brake
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0409 00-1
Excessive Oil Leaks (Winch Transfer Gearcase and Power Takeoff) ..................... 0094 00-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0407 00-5
Power Takeoff
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0415 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0415 00-2
Power Takeoff Control
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .. . .. . .. . .. . .. . .. . 0414 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .. . .. . .. . .. . .. . .. . 0414 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .. . .. . .. . .. . .. . .. . 0414 00-1
Power Takeoff Does Not Engage When Winch Control Is Actuated ... .. . .. . .. . .. . .. . .. . 0093 00-1
Propeller Shaft
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0412 00-4
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0412 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0412 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0412 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0407 00-2
Transfer Gearcase
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . .. . .. . .. . .. . .. . .. . 0413 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . .. . .. . .. . .. . .. . .. . 0413 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . .. . .. . .. . .. . .. . .. . 0413 00-1
Winch Brake Does Not Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . .. . .. . .. . .. . .. . .. . 0092 00-1
Winch Case Overheats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . .. . .. . .. . .. . .. . .. . 0089 00-1
Winch Does Not Turn With Drum Clutch In "Clutch In" Position . ... . .. . .. . .. . .. . .. . .. . 0090 00-1
Winch Drum Does Not Turn Drum Clutch In "Clutch Out" Position .. . .. . .. . .. . .. . .. . .. . 0091 00-1
Winch Propeller Shaft Noisy During Operation . . . . . . . . . . . . . . ... . .. . .. . .. . .. . .. . .. . 0095 00-1
Wire Rope, Hook, and Chain
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0416 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0416 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...................... 0416 00-2
Windows
Cab
Installation . ........................................................... 0458 00-2
Removal . . . ........................................................... 0458 00-1
Cab Door
Installation . ........................................................... 0387 00-4
Removal . . . ........................................................... 0387 00-2
Insulated Cover
Installation . ........................................................... 0468 00-2
Removal . . . ........................................................... 0468 00-1
Thermal Door
Installation . ........................................................... 0461 00-2
Removal . . . ........................................................... 0461 00-1
Index-51 Change 1
TM 9-2350-247-20-3
INDEX, cont’d
Windshield and Frame

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0392 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0392 00-2
Windshield Wiper
Arm and Blade
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0422 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0422 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0422 00-1
Linkage
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0421 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0421 00-2
Motor
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0420 00-2
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0420 00-1
Switch
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-2
Winterization System
Coolant Heater Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0086 00-1
Wire Rope, Winch (M548A1)

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0416 00-2
Wiring Harness
Battery to Regulator Cable Jack (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . ....................................... 0299 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0299 00-2
Engine Coolant Heater
Cleaning . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0473 00-2
Installation . . . . . . . . . . . . . . . . . . . . . ....................................... 0473 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0473 00-1
Fuel Pump (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . ....................................... 0302 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0302 00-1
Generator to Regulator
M548A1
Installation . . . . . . . . . . . . . . . . . . . ....................................... 0295 00-2
Removal . . . . . . . . . . . . . . . . . . . . . ....................................... 0295 00-1
M548A3
Installation . . . . . . . . . . . . . . . . . . . ....................................... 0296 00-3
Removal . . . . . . . . . . . . . . . . . . . . . ....................................... 0296 00-1
Ground Lead, Engine (M548A3)
Installation . . . . . . . . . . . . . . . . . . . . . ....................................... 0300 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . ....................................... 0300 00-2
NBC (M548A3)
From Battery Compartment to Maniold
Installation . . . . . . . . . . . . . . . . . . . ....................................... 0531 00-4
Removal . . . . . . . . . . . . . . . . . . . . . ....................................... 0531 00-2
Change 1 Index-52
TM 9-2350-247-20-3
INDEX, cont’d
Power Plant (M548A3)

Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0298 00-8
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0298 00-2
Repair
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0294 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0294 00-1
Trailer
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0301 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0301 00-1
Transmission (M548A3)
Inspection-Acceptance and Rejection Criteria ................................... 0297 00-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0297 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0297 00-2
Turn Signal Front
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0511 00-5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0511 00-1
Turn Signal Rear
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0512 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0512 00-1
M548A1
Installation . . . . . . . . . . . . . . . . . . . . . . .................................... 0451 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0451 00-2
M548A3
Installation . . . . . . . . . . . . . . . . . . . . . . .................................... 0435 00-4
Removal . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0435 00-2
Vehicle Compartment Heater Defroster Fan
Installation . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0434 00-3
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .................................... 0434 00-2
Index-53/54 blank Change 1

TM 9-2350-247-20-3
M548A1 Carrier
Electrical Circuit Diagram
FO-1
TM 9-2350-247-20-3
M548A3 CARRIER ELECTRICAL CIRCUIT DIAGRAM

FO-2 (SHEET 1 OF 6)
TM 9-2350-247-20-3

FO-2 (SHEET 2 OF 6)
TM 9-2350-247-20-3

FO-2 (SHEET 3 OF 6)
TM 9-2350-247-20-3

FO-2 (SHEET 4 OF 6)
TM 9-2350-247-20-3

FO-2 (SHEET 5 OF 6)
TM 9-2350-247-20-3

FO-2 (SHEET 6 OF 6)
Use Part II (reverse) for Repair Date
Parts and Special Tools Lists
RECOMMENDED CHANGES TO PUBLICATIONS (RPSTL) and Supply
AND BLANK FORMS Catalogs/Supply Manuals SC/SM).
For use of this form, see AR 25-30; the proponent agency is

ODISC4.
TO: (Forward to proponent of publication or form) (Include ZIP Code) FROM: (Activity and location) (include ZIP code)
PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER DATE TITLE

TM 9-2350-247-20-3 30 June 2001 Unit Maintenance Manual for Carrier,
Cargo Tracked, 6-Ton M548A1 and
M548A3
ITEM PAGE PARA LINE FIGURE TABLE RECOMMENDED CHANGES AND REASON
NO.
0052 00-4 Inspection Step 1 WP reference should be (WP 0003 00)
*Reference to line numbers within the paragraph or subparagraph.

TYPED, GRADE OR TITLE TELEPHONE EXCHANGE/AUTOVON, PLUS SIGNATURE
EXTENSION
DA FORM 2028, FEB 74 REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.0
TO: (Forward direct to addressee FROM: (Activity and location) (Include Date
listed in publication) Zip Code)
PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER DATE TITLE
TM 9-2350-247-20-3 30 June 2001 Unit Maintenance Manual for Carrier, Cargo Tracked, 6-
Ton M548A1 and M548A3
PAGE COLM LINE NATIONAL STOCK REFERENCE FIGURE ITEM TOTAL NO.
NO. NO. NO. NUMBER NO. NO. NO. OF MAJOR RECOMMENDED ACTION
ITEMS
SUPPORTED
PART III – REMARKS (Any general remarks or recommendations, or suggestions for improvement of publications and blank forms.
Additional blank sheets may be used if more space is needed).

EXTENSION
USAPPC V3.00
Parts and
RECOMMENDED CHANGES TO PUBLICATIONS Special Tools Lists (RPSTL) and
AND BLANK FORMS Supply
Catalogs/Supply Manuals SC/SM).
ODISC4.

M548A3
NO.

EXTENSION
DA FORM 2028, FEB 74 REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
ITEMS
SUPPORTED

EXTENSION
USAPPC V3.00
Parts and
ODISC4.

M548A3
NO.

EXTENSION
DA FORM 2028, FEB 74 REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED. USAPPC
V3.00
ITEMS
SUPPORTED

EXTENSION
USAPPC V3.00
Parts and
ODISC4.

M548A3
NO.

EXTENSION
V3.00
ITEMS
SUPPORTED

EXTENSION
USAPPC V3.00
Parts and
ODISC4.

M548A3
NO.

EXTENSION
V3.00
ITEMS
SUPPORTED

EXTENSION
USAPPC V3.00
By Order of the Secretary of the Army:
ERIC K. SHINSEKI
General, United States Army
Official Chief of Staff
JOEL B. HUDSON
Administrative Assistant to the
Secretary of the Army
0105109
DISTRIBUTION:
To be distributed in accordance with the initial distribution number (IDN) 372382,

requirements for TM 9-2350-247-20-3.
THE METRIC SYSTEM AND EQUIVALENTS
LINEAR MEASURE SQUARE MEASURE

1 Centimeter = 10 Millimeters = 0.01 Meters = 0.3937 Inches 1 Sq. Centimeter = 100 Sq. Millimeters = 0.155 Sq. Inches
1 Meter = 100 Centimeters = 1000 Millimeters = 39.37 Inches 1 Sq. Meter = 10,000 Sq. Centimeters = 10.76 Sq. Feet
1 Kilometer = 1000 Meters = 0.621 Miles 1 Sq. Kilometer = 1,000 Sq. Meters = 0.386 Sq. Miles
WEIGHTS CUBIC MEASURE
1 Gram = 0.001 Kilograms = 1000 Milligrams = 0.035 Ounces 1 Cu. Centimeter = 1000 Cu. Millimeters = 0.06 Cu. Inches
1 Kilogram = 1000 Grams = 2.2 Lb. 1 Cu. Meter = 1,000,000 Cu. Centimeters = 35.31 Cu. Feet
1 Metric Ton = 1000 Kilograms = 1 Megagram = 1.1 Short Tons TEMPERATURE
LIQUID MEASURE 5/9 (ºF - 32) = ºC
1 Milliliter = 0.001 Liters = 0.0338 Fluid Ounces 212º Fahrenheit is equivalent to 100º Celsius
1 Liter = 1000 Milliliters = 33.82 Fluid Ounces 90º Fahrenheit is equivalent to 32.2º Celsius
32º Fahrenheit is equivalent to 0º Celsius
(9/5 x ºC) + 32 = ºF
TO CHANGE TO MULTIPLY BY
Inches ......................................... Centimeters..................................... 2.540
Feet ............................................. Meters............................................. 0.305
Yards .......................................... Meters............................................. 0.914
Miles........................................... Kilometers ...................................... 1.609
Square Inches ............................. Square Centimeters......................... 6.451
Square Feet ................................. Square Meters................................. 0.093
Square Yards .............................. Square Meters................................. 0.836
Square Miles............................... Square Kilometers .......................... 2.590
Acres........................................... Square Hectometers ........................ 0.405
Cubic Feet .................................. Cubic Meters .................................. 0.028
Cubic Yards................................ Cubic Meters .................................. 0.765
Fluid Ounces .............................. Millimeters ................................... 29.573
Pints............................................ Liters............................................... 0.473
Quarts ......................................... Liters............................................... 0.946
Gallons ....................................... Liters............................................... 3.785
Ounces........................................ Grams ........................................... 28.349
Pounds ........................................ Kilograms ....................................... 0.454
Short Tons .................................. Metric Tons .................................... 0.907
Pound-Feet.................................. Newton-Meters ............................... 1.356
Pounds per Square Inch .............. Kilopascals ..................................... 6.895
Miles per Gallon ......................... Kilometers per Liter........................ 0.425
Miles per Hour............................ Kilometers per Hour ....................... 1.609
TO CHANGE TO MULTIPLY BY
Centimeters................................. Inches ............................................. 0.394
Meters......................................... Feet ................................................. 3.280
Meters......................................... Yards .............................................. 1.094
Kilometers .................................. Miles............................................... 0.621
Square Centimeters..................... Square Inches.................................. 0.155
Square Meters............................. Square Feet ................................... 10.764
Square Meters............................. Square Yards .................................. 1.196
Square Kilometers ...................... Square Miles................................... 0.386
Square Hectometers.................... Acres............................................... 2.471
Cubic Meters .............................. Cubic Feet .................................... 35.315
Cubic Meters .............................. Cubic Yards.................................... 1.308
Milliliters.................................... Fluid Ounces................................... 0.034
Liters........................................... Pints................................................ 2.113
Liters........................................... Quarts ............................................. 1.057
Liters........................................... Gallons............................................ 0.264
Grams ......................................... Ounces............................................ 0.035
Kilograms ................................... Pounds ............................................ 2.205
Metric Tons ................................ Short Tons ...................................... 1.102
Newton-Meters ........................... Pound-Feet...................................... 0.738
Kilopascals ................................. Pounds per Square Inch .................. 0.145
Kilometers per Liter.................... Miles per Gallon ............................. 2.354
Kilometers per Hour ................... Miles per Hour................................ 0.621
PIN: 073085-000

TM 9-2350-247-20-3

Uploaded by

Copyright:

Available Formats

TM 9-2350-247-20-3

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TM 9-2350-247-20-3

Uploaded by

Copyright:

Available Formats

TM 9-2350-247-20-3

UNIT MAINTENANCE MANUAL

DISTRIBUTION STATEMENT A — Approved for public release; distribution is unlimited.

HEADQUARTERS, DEPARTMENT OF THE ARMY

CARRIER, CARGO TRACKED, 6-TON

CARRIER, CARGO TRACKED, 6-TON

DISTRIBUTION STATEMENT A – Approved for public release; distribution is unlimited.

TM 9-2350-247-20-3, 30 June 2001 is updated as follows:

By Order of the Secretary of the Army:

INSERT LATEST UPDATED PAGES/WORK PACKAGES. DESTROY SUPERSEDED DATA.

LIST OF EFFECTIVE PAGES/WORK PACKAGES

Dates of issue for original and updated pages/work packages are:

Original 0 (30 June 2001)

Page/WP *Change Page/WP *Change Page/WP *Change

*Zero in this column indicates an original page

CARRIER, CARGO TRACKED, 6–TON M548A1

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

CURRENT AS OF 5 JANUARY 2004

SUPERSEDURE NOTICE — This manual supersedes TM 9–2350–247–20–3 dated August 1994.

DISTRIBUTION STATEMENT A — Approved for public release; distribution is unlimited.

CHAPTER 17 — UNIT MAINTENANCE INSTRUCTIONS FOR SHOCK ABSORBERS

CHAPTER 18 — UNIT MAINTENANCE INSTRUCTIONS FOR HULL

TABLE OF CONTENTS (cont)

REPLACE DOOR WINDOWS...........................................................................................................................0387 00

CHAPTER 19 — UNIT MAINTENANCE INSTRUCTIONS FOR WINCH AND

CHAPTER 20 — UNIT MAINTENANCE INSTRUCTIONS FOR HULL ACCESSORY ITEMS

TABLE OF CONTENTS (cont)

CHAPTER 21 — UNIT MAINTENANCE INSTRUCTIONS FOR TOOLS AND

CHAPTER 22 — UNIT MAINTENANCE INSTRUCTIONS FOR SPECIAL PURPOSE KITS

TABLE OF CONTENTS (cont)

REPLACE VEHICLE COMPARTMENT HEATER WIRING HARNESS (M548A1).....................................0451 00

TABLE OF CONTENTS (cont)

REPLACE RIFLE RACK...................................................................................................................................0488 00

CHAPTER 23 — UNIT MAINTENANCE INSTRUCTIONS FOR GAUGES

TABLE OF CONTENTS (cont)

CHAPTER 24 — UNIT MAINTENANCE INSTRUCTIONS FOR FIRE

CHAPTER 25 — UNIT MAINTENANCE INSTRUCTIONS FOR NBC SYSTEM (M548A3)

CHAPTER 26 — UNIT SUPPORTING INFORMATION

WORK PACKAGE INDEX

REPLACE SHOCK ABSORBER 0379 00

Removal (page 0379 00-1).

Maintenance Level Personnel Required

Tools and Special Tools References

REPLACE SHOCK ABSORBER — Continued 0379 00

REPLACE SHOCK ABSORBER — Continued 0379 00

1. Install new inner seal (1) on support arm pin (2).

REPLACE SHOCK ABSORBER — Continued 0379 00

4. Secure shock absorber (3) with two nuts (7).

REPLACE SHOCK ABSORBER PIN 0380 00

Removal (page 0380 00-1).

Maintenance Level References

REPLACE SHOCK ABSORBER PIN — Continued 0380 00

REPLACE SHOCK ABSORBER MOUNT 0381 00

Removal (page 0381 00-1).

Maintenance Level References

Tools and Special Tools Equipment Condition

1. Remove three screws (1) from shock absorber mount (2).

2. Remove shock absorber mount (2) from hull.

REPLACE SHOCK ABSORBER MOUNT — Continued 0381 00

WORK PACKAGE INDEX

Page/WP Change Page/WP Change Page/WP *Change