Chapter 10:

1. A radian is about: A. 25 B. 37 C. 45 D. 57 E. 90 ans: D 2. One revolution is the same as: A. 1 rad B. 57 rad C. /2 rad D. rad E. 2 rad ans: E 3. One revolution per minute is about: A. 0.0524 rad/s B. 0.105 rad/s C. 0.95 rad/s D. 1.57 rad/s E. 6.28 rad/s ans: B 4. If a A. B. C. D. E.

ROTATION

wheel turns with constant angular speed then: each point on its rim moves with constant velocity each point on its rim moves with constant acceleration the wheel turns through equal angles in equal times the angle through which the wheel turns in each second increases as time goes on the angle through which the wheel turns in each second decreases as time goes on ans: C wheel is turning at 3.0 rad/s, the time it takes to complete one revolution is about: 0.33 s 0.67 s 1.0 s 1.3 s 2.1 s ans: E

5. If a A. B. C. D. E.

140

Chapter 10:

ROTATION

6. If wheel turning at a constant rate completes 100 revolutions in 10 s its angular speed is: A. 0.31 rad/s B. 0.63 rad/s C. 10 rad/s D. 31 rad/s E. 63 rad/s ans: E 7. The angular speed of the second hand of a watch is: A. ( /1800) rad/s B. ( /60) m/s C. ( /30) m/s D. (2 ) m/s E. (60) m/s ans: C 8. The angular speed of the minute hand of a watch is: A. (60/ ) m/s B. (1800/ ) m/s C. ( ) m/s D. ( /1800) m/s E. ( /60) m/s ans: D 9. A ywheel is initially rotating at 20 rad/s and has a constant angular acceleration. After 9.0 s it has rotated through 450 rad. Its angular acceleration is: A. 3.3 rad/s B. 4.4 rad/s C. 5.6 rad/s D. 6.7 rad/s E. 11 rad/s ans: D 10. Ten seconds after an electric fan is turned on, the fan rotates at 300 rev/min. Its average angular acceleration is: A. 3.14 rad/s2 B. 30 rad/s2 2 C. 30 rev/s 2 D. 50 rev/min E. 1800 rev/s2 ans: A

Chapter 10:

ROTATION

141

11. A wheel rotates with a constant angular acceleration of rad/s . During a certain time interval its angular displacement is rad. At the end of the interval its angular velocity is 2 rad/s. Its angular velocity at the beginning of the interval is: A. zero B. 1 rad/s C. rad/s D. 2 rad/s E. 2 rad/s ans: D 12. A ywheel rotating at 12 rev/s is brought to rest in 6 s. The magnitude of the average angular acceleration in rad/s2 of the wheel during this process is: A. 1/ B. 2 C. 4 D. 4 E. 72 ans: D 13. A phonograph turntable, initially rotating at 0.75 rev/s, slows down and stops in 30 s. The magnitude of its average angular acceleration in rad/s2 for this process is: A. 1.5 B. 1.5 C. /40 D. /20 E. 0.75 ans: D 14. The angular velocity of a rotating wheel increases by 2 rev/s every minute. The angular acceleration in rad/s2 of this wheel is: A. 42 B. 2 C. 1/30 D. /15 E. 4 ans: D 15. A wheel initially has an angular velocity of 18 rad/s. It has a constant angular acceleration of 2 2.0 rad/s and is slowing at rst. What time elapses before its angular velocity is 18 rad/s in the direction opposite to its initial angular velocity? A. 3.0 s B. 6.0 s C. 9.0 s D. 18 s E. 36 s ans: D

142

Chapter 10:

ROTATION

16. A wheel initially has an angular velocity of 36 rad/s but after 6.0 s its angular velocity is 24 rad/s. If its angular acceleration is constant its value is: A. B. C. D. E. 2.0 rad/s 2.0 rad/s2 2 3.0 rad/s 2 3.0 rad/s 2 6.0 rad/s ans: B
2

17. A wheel initially has an angular velocity of 36 rad/s but after 6.0 s its angular velocity is 24 rad/s. If its angular acceleration is constant the value is: A. B. C. D. E. 2.0 rad/s 2.0 rad/s2 2 3.0 rad/s 2 3.0 rad/s 2 6.0 rad/s ans: A
2

18. A wheel initially has an angular velocity of 18 rad/s but it is slowing at a rate of 2.0 rad/s . By the time it stops it will have turned through: A. 81 rad B. 160 rad C. 245 rad D. 330 rad E. 410 rad ans: A 19. A wheel starts from rest and has an angular acceleration of 4.0 rad/s . When it has made 10 rev its angular velocity is: A. 16 rad/s B. 22 rad/s C. 32 rad/s D. 250 rad/s E. 500 rad/s ans: B 20. A wheel starts from rest and has an angular acceleration of 4.0 rad/s . The time it takes to make 10 rev is: A. 0.50 s B. 0.71 s C. 2.2 s D. 2.8 s E. 5.6 s ans: E
2 2

Chapter 10:

ROTATION

143

21. A wheel starts from rest and has an angular acceleration that is given by (t) = (6 rad/s )t2 . The angle through which it turns in time t is given by: A. [(1/8)t4 ] rad B. [(1/4)t4 ] rad C. [(1/2)t4 ] rad D. (t4 ) rad E. 12 rad ans: C 22. A wheel starts from rest and has an angular acceleration that is given by (t) = (6.0 rad/s )t2 . The time it takes to make 10 rev is: A. 2.8 s B. 3.3 s C. 4.0 s D. 4.7 s E. 5.3 s ans: B 23. A wheel starts from rest and has an angular acceleration that is given by (t) = (6.0 rad/s4 )t2 . After it has turned through 10 rev its angular velocity is: A. 63 rad/s B. 75 rad/s C. 89 rad/s D. 130 rad/s E. 210 rad/s ans: B 24. A wheel is spinning at 27 rad/s but is slowing with an angular acceleration that has a magnitude 4 given by (3.0 rad/s )t2 . It stops in a time of: A. 1.7 s B. 2.6 s C. 3.0 s D. 4.4 s E. 7.3 s ans: C 25. If the angular velocity vector of a spinning body points out of the page then, when viewed from above the page, the body is spinning: A. clockwise about an axis that is perpendicular to the page B. counterclockwise about an axis that is perpendicular to the page C. about an axis that is parallel to the page D. about an axis that is changing orientation E. about an axis that is getting longer ans: B
4

144

Chapter 10:

ROTATION

26. The angular velocity vector of a spinning body points out of the page. If the angular acceleration vector points into the page then: A. the body is slowing down B. the body is speeding up C. the body is starting to turn in the opposite direction D. the axis of rotation is changing orientation E. none of the above ans: A 27. A child, riding on a large merry-go-round, travels a distance of 3000 m in a circle of diameter 40 m. The total angle through which she revolves is: A. 50 rad B. 75 rad C. 150 rad D. 314 rad E. none of these ans: C 28. The gure shows a cylinder of radius 0.7 m rotating about its axis at 10 rad/s. The speed of the point P is:
. . . . . . P....... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . .

A. B. C. D. E.

7.0 m/s 14 rad/s 7.0 rad/s 0.70 m/s none of these ans: A

Chapter 10:

ROTATION

145

29. The fan shown has been turned on and is now slowing as it rotates clockwise. The direction of the acceleration of the point X on the fan tip could be:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .. . . . . .. . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . .. . . . . . .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. . . .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .. . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .. . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . ... . . .

. . . . . . ... ... ....

A. B. C. D. E. ans: D 30. A wheel of diameter 3.0 cm has a 4.0-m cord wrapped around its periphery. Starting from rest, 2 the wheel is given a constant angular acceleration of 2.0 rad/s . The cord will unwind in: A. 0.82 s B. 2.0 s C. 8.0 s D. 16 s E. 130 s ans: D 31. A particle moves in a circular path of radius 0.10 m with a constant angular speed of 5 rev/s. The acceleration of the particle is: 2 A. 0.10 m/s 2 B. 0.50 m/s C. 500 m/s2 2 D. 10002 m/s 2 E. 102 m/s ans: E 32. A car travels north at constant velocity. It goes over a piece of mud, which sticks to the tire. The initial acceleration of the mud, as it leaves the ground, is: A. vertically upward B. horizontally to the north C. horizontally to the south D. zero E. upward and forward at 45 to the horizontal ans: A

146

Chapter 10:

ROTATION

33. Wrapping paper is being from a 5.0-cm radius tube, free to rotate on its axis. If it is pulled at the constant rate of 10 cm/s and does not slip on the tube, the angular velocity of the tube is: A. 2.0 rad/s B. 5.0 rad/s C. 10 rad/s D. 25 rad/s E. 50 rad/s ans: A 34. String is wrapped around the periphery of a 5.0-cm radius cylinder, free to rotate on its axis. The string is pulled straight out at a constant rate of 10 cm/s and does not slip on the cylinder. As each small segment of string leaves the cylinder, its acceleration changes by: A. 0 2 B. 0.010 m/s C. 0.020 m/s2 D. 0.10 m/s2 2 E. 0.20 m/s ans: E 35. A ywheel of diameter 1.2 m has a constant angular acceleration of 5.0 rad/s2 . The tangential acceleration of a point on its rim is: A. 5.0 rad/s2 B. 3.0 m/s2 C. 5.0 m/s2 2 D. 6.0 m/s 2 E. 12 m/s ans: B 36. For a wheel spinning with constant angular acceleration on an axis through its center, the ratio of the speed of a point on the rim to the speed of a point halfway between the center and the rim is: A. 1 B. 2 C. 1/2 D. 4 E. 1/4 ans: B 37. For a wheel spinning on an axis through its center, the ratio of the tangential acceleration of a point on the rim to the tangential acceleration of a point halfway between the center and the rim is: A. 1 B. 2 C. 1/2 D. 4 E. 1/4 ans: B Chapter 10: ROTATION 147

38. For a wheel spinning on an axis through its center, the ratio of the radial acceleration of a point on the rim to the radial acceleration of a point halfway between the center and the rim is: A. 1 B. 2 C. 1/2 D. 4 E. 1/4 ans: B 39. Two wheels are identical but wheel B is spinning with twice the angular speed of wheel A. The ratio of the magnitude of the radial acceleration of a point on the rim of B to the magnitude of the radial acceleration of a point on the rim of A is: A. 1 B. 2 C. 1/2 D. 4 E. 1/4 ans: D 40. A wheel starts from rest and spins with a constant angular acceleration. As time goes on the acceleration vector for a point on the rim: A. decreases in magnitude and becomes more nearly tangent to the rim B. decreases in magnitude and becomes more early radial C. increases in magnitude and becomes more nearly tangent to the rim D. increases in magnitude and becomes more nearly radial E. increases in magnitude but retains the same angle with the tangent to the rim ans: D 41. The magnitude of the acceleration of a point on a spinning wheel is increased by a factor of 4 if: A. the magnitudes of the angular velocity and the angular acceleration are each multiplied by a factor of 4 B. the magnitude of the angular velocity is multiplied by a factor of 4 and the angular acceleration is not changed C. the magnitudes of the angular velocity and the angular acceleration are each multiplied by a factor of 2 D. the magnitude of the angular velocity is multiplied by a factor of 2 and the angular acceleration is not changed E. the magnitude of the angular velocity is multiplied by a factor of 2 and the magnitude of the angular acceleration is multiplied by a factor of 4 ans: E

148

Chapter 10:

ROTATION

42. Three identical balls are tied by light strings to the same rod and rotate around it, as shown below. Rank the balls according to their rotational inertia, least to greatest. 1 m ball 1 2m

ball 2

3m

ball 3

A. B. C. D. E.

1, 2, 3 3, 2, 1 3, then 1 and 2 tie 1, 3, 2 All are the same ans: A

43. Four identical particles, each with mass m, are arranged in the x, y plane as shown. They are connected by light sticks to form a rigid body. If m = 2.0 kg and a = 1.0 m, the rotational inertia of this array about the y axis is: y

a a

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A. B. C. D. E.

4.0 kg m2 12 kg m2 9.6 kg m2 4.8 kg m2 none of these ans: B

Chapter 10:

ROTATION

149

44. Three identical balls, with masses of M , 2M , and 3M , are fastened to a massless rod of length L as shown. The rotational inertia about the left end of the rod is:

L/2 L/2

3M

2M

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A. B. C. D. E.

M L2 /2 M L2 3M L2 /2 6M L2 3M L2 /4 ans: E

45. The rotational inertia of a thin cylindrical shell of mass M , radius R, and length L about its central axis (XX ) is:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

L A. B. C. D. E. M R2 /2 M L2 /2 M L2 M R2 none of these ans: D

| R |

46. The rotational inertia of a wheel about its axle does not depend upon its: A. diameter B. mass C. distribution of mass D. speed of rotation E. material composition ans: D

150

Chapter 10:

ROTATION

47. Consider four objects, each having the same mass and the same radius: 1. a solid sphere 2. a hollow sphere 3. a at disk in the x, y plane 4. a hoop in the x, y plane The order of increasing rotational inertia about an axis through the center of mass and parallel to the z axis is: A. 1, 2, 3, 4 B. 4, 3, 2, 1 C. 1, 3, 2, 4 D. 4, 2, 3, 1 E. 3, 1, 2, 4 ans: C 48. A and B are two solid cylinders made of aluminum. Their dimensions are shown. The ratio of the rotational inertia of B to that of A about the common axis XX is:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

R X

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

| 2R |

2L A. B. C. D. E. 2 4 8 16 32 ans: E

49. Two uniform circular disks having the same mass and the same thickness are made from dierent materials. The disk with the smaller rotational inertia is: A. the one made from the more dense material B. the one made from the less dense material C. neither both rotational inertias are the same D. the disk with the larger angular velocity E. the disk with the larger torque ans: A

Chapter 10:

ROTATION

151

50. A uniform solid cylinder made of lead has the same mass and the same length as a uniform solid cylinder made of wood. The rotational inertia of the lead cylinder compared to the wooden one is: A. greater B. less C. same D. unknown unless the radii are given E. unknown unless both the masses and the radii are given ans: B 51. To A. B. C. increase the rotational inertia of a solid disk about its axis without changing its mass: drill holes near the rim and put the material near the axis drill holes near the axis and put the material near the rim drill holes at points on a circle near the rim and put the material at points between the holes D. drill holes at points on a circle near the axis and put the material at points between the holes E. do none of the above (the rotational inertia cannot be changed without changing the mass) ans: B

52. The rotational inertia of a disk about its axis is 0.70 kg m2 . When a 2.0-kg weight is added to its rim, 0.40 m from the axis, the rotational inertia becomes: A. 0.38 kg m2 B. 0.54 kg m2 C. 0.70 kg m2 D. 0.86 kg m2 E. 1.0 kg m2 ans: E 53. When a thin uniform stick of mass M and length L is pivoted about its midpoint, its rotational inertia is M L2 /12. When pivoted about a parallel axis through one end, its rotational inertia is: A. M L2 /12 B. M L2 /6 C. M L2 /3 D. 7M L2 /12 E. 13M L2 /12 ans: C 54. The rotational inertia of a solid uniform sphere about a diameter is (2/5)M R2 , where M is its mass and R is its radius. If the sphere is pivoted about an axis that is tangent to its surface, its rotational inertia is: A. M R2 B. (2/5)M R2 C. (3/5)M R2 D. (5/2)M R2 E. (7/5)M R2 ans: E 152 Chapter 10: ROTATION

55. A solid uniform sphere of radius R and mass M has a rotational inertia about a diameter that is given by (2/5)M R2 . A light string of length 3R is attached to the surface and used to suspend the sphere from the ceiling. Its rotational inertia about the point of attachment at the ceiling is: A. (2/5)M R2 B. 9M R2 C. 16M R2 D. (47/5)M R2 E. (82/5)M R2 ans: E 56. A force with a given magnitude is to be applied to a wheel. The torque can be maximized by: A. applying the force near the axle, radially outward from the axle B. applying the force near the rim, radially outward from the axle C. applying the force near the axle, parallel to a tangent to the wheel D. applying the force at the rim, tangent to the rim E. applying the force at the rim, at 45 to the tangent ans: D 57. The meter stick shown below rotates about an axis through the point marked , 20 cm from one end. Five forces act on the stick: one at each end, one at the pivot point, and two 40 cm from one end, as shown. The magnitudes of the forces are all the same. Rank the forces according to the magnitudes of the torques they produce about the pivot point, least to greatest. F1
. . . . . . . . . . .. . . . . .. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F5 0 cm 20 cm 40 cm 60 cm 80 cm 100 cm

. . . . . . . . . . . . .. . . . . . . . . . . . . .. . . . . . . . ..

F2

F3

. . . . . . . 4 . . . .. . . . . . .. . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. .. . . . . ..

A. B. C. D. E.

F1 , F2 , F1 and F2 and F2 , F5 , F2 and ans: E

F3 , F4 , F5 F2 tie, then F3 , F4 , F5 F5 tie, then F4 , F1 , F3 F1 and F3 tie, then F4 F5 tie, then F4 , then F1 and F3 tie

Chapter 10:

ROTATION

153

58. A rod is pivoted about its center. A 5-N force is applied 4 m from the pivot and another 5-N force is applied 2 m from the pivot, as shown. The magnitude of the total torque about the pivot (in Nm) is:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . .. . . . . . 5N . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .

30

...................

. . . . . . . . .

2.0 m

4.0 m

30

5N

A. B. C. D. E.

0 5 8.7 15 26 ans: D

59. = I for an object rotating about a xed axis, where is the net torque acting on it, I is its rotational inertia, and is its angular acceleration. This expression: A. is the denition of torque B. is the denition of rotational inertia C. is the denition of angular acceleration D. follows directly from Newtons second law E. depends on a principle of physics that is unrelated to Newtons second law ans: D 60. A meter stick on a horizontal frictionless table top is pivoted at the 80-cm mark. It is initially at rest. A horizontal force F1 is applied perpendicularly to the end of the stick at 0 cm, as shown. A second horizontal force F2 (not shown) is applied at the 100-cm end of the stick. If the stick does not rotate: F1 0 cm 20 cm 40 cm 60 cm 80 cm 100 cm A. B. C. D. E. |F2 | > |F1 | |F2 | < |F1 | |F2 | = |F1 | |F2 | > |F1 | |F2 | > |F1 | ans: A for for for for for all orientations of all orientations of all orientations of some orientations some orientations F2 F2 F2 of F2 and |F2 | < |F1 | for others of F2 and |F2 | = |F1 | for others
. . . . . . . . . . . .. . . . . . .. . . . . . . . . . . . . .

154

Chapter 10:

ROTATION

61. A uniform disk, a thin hoop, and a uniform sphere, all with the same mass and same outer radius, are each free to rotate about a xed axis through its center. Assume the hoop is connected to the rotation axis by light spokes. With the objects starting from rest, identical forces are simultaneously applied to the rims, as shown. Rank the objects according to their angular accelerations, least to greatest. disk
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

hoop
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

sphere
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . .

A. B. C. D. E.

disk, hoop, sphere hoop, disk, sphere hoop, sphere, disk hoop, disk, sphere sphere, disk, hoop ans: D

62. A disk is free to rotate on a xed axis. A force of given magnitude F , in the plane of the disk, is to be applied. Of the following alternatives the greatest angular acceleration is obtained if the force is: A. applied tangentially halfway between the axis and the rim B. applied tangentially at the rim C. applied radially halfway between the axis and the rim D. applied radially at the rim E. applied at the rim but neither radially nor tangentially ans: B 63. A cylinder is 0.10 m in radius and 0.20 m in length. Its rotational inertia, about the cylinder axis on which it is mounted, is 0.020 kg m2 . A string is wound around the cylinder and pulled with a force of 1.0 N. The angular acceleration of the cylinder is: 2 A. 2.5 rad/s B. 5.0 rad/s2 2 C. 10 rad/s 2 D. 15 rad/s 2 E. 20 rad/s ans: B

Chapter 10:

ROTATION

155

64. A disk with a rotational inertia of 2.0 kg m2 and a radius of 0.40 m rotates on a frictionless xed axis perpendicular to the disk faces and through its center. A force of 5.0 N is applied tangentially to the rim. The angular acceleration of the disk is: 2 A. 0.40 rad/s B. 0.60 rad/s2 C. 1.0 rad/s2 2 D. 2.5 rad/s 2 E. 10 rad/s ans: C 65. A disk with a rotational inertia of 5.0 kg m2 and a radius of 0.25 m rotates on a frictionless xed axis perpendicular to the disk and through its center. A force of 8.0 N is applied along the rotation axis. The angular acceleration of the disk is: A. 0 2 B. 0.40 rad/s C. 0.60 rad/s2 2 D. 1.0 rad/s 2 E. 2.5 rad/s ans: A 66. A disk with a rotational inertia of 5.0 kg m2 and a radius of 0.25 m rotates on a frictionless xed axis perpendicular to the disk and through its center. A force of 8.0 N is applied tangentially to the rim. If the disk starts at rest, then after it has turned through half a revolution its angular velocity is: A. 0.57 rad/s B. 0.64 rad/s C. 0.80 rad/s D. 1.6 rad/s E. 3.2 rad/s ans: D 67. A thin circular hoop of mass 1.0 kg and radius 2.0 m is rotating about an axis through its center 2 and perpendicular to its plane. It is slowing down at the rate of 7.0 rad/s . The net torque acting on it is: A. 7.0 N m B. 14.0 N m C. 28.0 N m D. 44.0 N m E. none of these ans: C

156

Chapter 10:

ROTATION

68. A certain wheel has a rotational inertia of 12 kg m2 . As it turns through 5.0 rev its angular velocity increases from 5.0 rad/s to 6.0 rad/s. If the net torque is constant its value is: A. 0.016 N m B. 0.18 N m C. 0.57 N m D. 2.1 N m E. 3.6 N m ans: D 69. A 16-kg block is attached to a cord that is wrapped around the rim of a ywheel of diameter 0.40 m and hangs vertically, as shown. The rotational inertia of the ywheel is 0.50 kg m2 . When the block is released and the cord unwinds, the acceleration of the block is:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. .. .. .. .. .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . .. . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

| | 0.4 m | |

16 kg A. B. C. D. E. 0.15g 0.56g 0.84g g 1.3g ans: B

70. A 8.0-cm radius disk with a rotational inertia of 0.12 kg m2 is free to rotate on a horizontal axis. A string is fastened to the surface of the disk and a 10-kg mass hangs from the other end. The mass is raised by using a crank to apply a 9.0-Nm torque to the disk. The acceleration of the mass is: 2 A. 0.50 m/s 2 B. 1.7 m/s C. 6.2 m/s2 2 D. 12 m/s 2 E. 20 m/s ans: A

Chapter 10:

ROTATION

157

71. A 0.70-kg disk with a rotational inertia given by M R2 /2 is free to rotate on a xed horizontal axis suspended from the ceiling. A string is wrapped around the disk and a 2.0-kg mass hangs from the free end. If the string does not slip, then as the mass falls and the cylinder rotates, the suspension holding the cylinder pulls up on the cylinder with a force of: A. 6.9 N B. 9.8 N C. 16 N D. 26 N E. 29 N ans: B 72. A small disk of radius R1 is mounted coaxially with a larger disk of radius R2 . The disks are securely fastened to each other and the combination is free to rotate on a xed axle that is perpendicular to a horizontal frictionless table top, as shown in the overhead view below. The rotational inertia of the combination is I . A string is wrapped around the larger disk and attached to a block of mass m, on the table. Another string is wrapped around the smaller disk and is pulled with a force F as shown. The acceleration of the block is:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A. B. C. D. E.

R1 F/mR2 R1 R2 F/(I R1 R2 F/(I R1 R2 F/(I R1 R2 F/(I ans: C

2 mR2 ) 2 + mR2 ) mR1 R2 ) + mR1 R2 )

158

Chapter 10:

ROTATION

73. A small disk of radius R1 is fastened coaxially to a larger disk of radius R2 . The combination is free to rotate on a xed axle, which is perpendicular to a horizontal frictionless table top, as shown in the overhead view below. The rotational inertia of the combination is I . A string is wrapped around the larger disk and attached to a block of mass m, on the table. Another string is wrapped around the smaller disk and is pulled with a force F as shown. The tension in the string pulling the block is:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..

A. B. C. D. E.

R1 F/R2 mR1 R2 F/(I mR1 R2 F/(I mR1 R2 F/(I mR1 R2 F/(I ans: C

2 mR2 ) 2 + mR2 ) mR1 R2 ) + mR1 R2 )

74. A block is attached to each end of a rope that passes over a pulley suspended from the ceiling. The blocks do not have the same mass. If the rope does not slip on the pulley, then at any instant after the blocks start moving, the rope: A. pulls on both blocks, but exerts a greater force on the heavier block B. pulls on both blocks, but exerts a greater force on the lighter block C. pulls on both blocks and exerts the same magnitude force on both D. does not pull on either block E. pulls only on the lighter block ans: A 75. A pulley with a radius of 3.0 cm and a rotational inertia of 4.5 103 kg m2 is suspended from the ceiling. A rope passes over it with a 2.0-kg block attached to one end and a 4.0-kg block attached to the other. The rope does not slip on the pulley. When the speed of the heavier block is 2.0 m/s the kinetic energy of the pulley is: A. 0.15 J B. 0.30 J C. 1.0 J D. 10 J E. 20 J ans: D

Chapter 10:

ROTATION

159

76. A pulley with a radius of 3.0 cm and a rotational inertia of 4.5 103 kg m2 is suspended from the ceiling. A rope passes over it with a 2.0-kg block attached to one end and a 4.0-kg block attached to the other. The rope does not slip on the pulley. At any instant after the blocks start moving, the object with the greatest kinetic energy is: A. the heavier block B. the lighter block C. the pulley D. either block (the two blocks have the same kinetic energy) E. none (all three objects have the same kinetic energy) ans: C 77. A disk with a rotational inertia of 5.0 kg m2 and a radius of 0.25 m rotates on a xed axis perpendicular to the disk and through its center. A force of 2.0 N is applied tangentially to the rim. As the disk turns through half a revolution the work done by the force is: A. 1.6 J B. 2.5 J C. 6.3 J D. 10 J E. 40 J ans: A 78. A circular saw is powered by a motor. When the saw is used to cut wood, the wood exerts a torque of 0.80 N m on the saw blade. If the blade rotates with a constant angular velocity of 20 rad/s the work done on the blade by the motor in 1.0 min is: A. 0 B. 480 J C. 960 J D. 1400 J E. 1800 J ans: C 79. A disk has a rotational inertia of 6.0 kg m2 and a constant angular acceleration of 2.0 rad/s . If it starts from rest the work done during the rst 5.0 s by the net torque acting on it is: A. 0 B. 30 J C. 60 J D. 300 J E. 600 J ans: D 80. A disk starts from rest and rotates around a xed axis, subject to a constant net torque. The as the work done during the rst 5 s. work done by the torque during the second 5 s is A. the same B. twice as much C. half as much D. four times as much E. one-fourth as much ans: D 160 Chapter 10: ROTATION
2

81. A disk starts from rest and rotates about a xed axis, subject to a constant net torque. The as the work done during the work done by the torque during the second revolution is rst revolution. A. the same B. twice as much C. half as much D. four times as much E. one-fourth as much ans: A

Chapter 10:

ROTATION

161