Scribd
Upload
29 views

Example of Power Supply: Normal Temperature Type Extended Temperature Type

The document provides examples of temperature compensation circuits for extended temperature power supplies, including diagrams of circuits using a thermistor and resistors. It also includes instructions for an LCD module, describing the code used to perform functions like clearing the display, setting address registers, and reading or writing data from the character generator and display data RAM. Technical details are given for components in the example circuits like resistor values and operating voltages.

Uploaded by

rdc02271
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
29 views

Example of Power Supply: Normal Temperature Type Extended Temperature Type

The document provides examples of temperature compensation circuits for extended temperature power supplies, including diagrams of circuits using a thermistor and resistors. It also includes instructions for an LCD module, describing the code used to perform functions like clearing the display, setting address registers, and reading or writing data from the character generator and display data RAM. Technical details are given for components in the example circuits like resistor values and operating voltages.

Uploaded by

rdc02271
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

EXAMPLE OF POWER SUPPLY

Normal Temperature Type Extended Temperature Type

14 13 12

3 2

14 13

3 2

Vss Vcc VR

GND

Vss Vcc

GND

+5V Vo VR :10k ~ 20 k Vo

+5V

-7V

Examples of Temperature Compensation Circuits for Extended Temp. (Only for reference)
(A) 1/8Duty-1/4Bias
Vcc Vcc Vcc

(A) 1/16Duty-1/5Bias
Vcc

Rth Rs Rm
Vz

Rp

Vo RL

Module equivalent load

Rth Rs Rm Vz

Rp

Vo RL

Module equivalent load

Rth

Rp

Vo

RL

Module equivalent load

Rth

Rp

Vo

RL

Module equivalent load

Rs Module Rz
Vee

Rs

Module Rm Fig.2
Vz Vz

Module
Rz Fig.1

Fig.1

Rm

Module

Thermistor: Rth[25oC]= 15[k-ohm], B=4200(K) Resistors: Rp=30[K-ohm], Rs=6.8[k-ohm], Rm=3.3[k-ohm] Transistor: PNP Type Vcc: +5V , Vss: 0V [Logic Supply] Vz: -8[V] (-7.8 to -8.2[V]) Vee<Vz[V], Rz=[Vz-Vee] / 5[k-ohm]

Fig.2
Thermistor: Rth[25oC]= 15[k-ohm], B=4200(K) Resistors: Rp=510[K-ohm], Rs=8.2[k-ohm], Rm=3.9[k-ohm] Transistor: PNP Type Vcc: +5V , Vss: 0V [Logic Supply] Vz: -11[V] (-10.725 to -11.275[V]) Vee<Vz[V], Rz=[Vz-Vee] / 5[k-ohm]

INSTRUCTIONS
Code
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Instruction
Clear Display Cursor Art Home Entry Mode Set Display On/Off Control Cursor /Display Shift Function Set CG RAM Address Set DD RAM Address Set Busy Flag/ Address Read CG RAM / DD RAM Data Write CG RAM / DD RAM Data Read

Description
0 0 0 1 0 0 0 1 1 *
Clears all display and returns the cursor to the home position (Address 0). Returns the cursor to the home positio (Address 0). Also returns the display bing shifted to the original position. DD RAM contents remain unchanged. Sets the cursor move direction and specifies or not to shift the display. These operations are performed during data write and read. Sets ON/OFF of all display (D), cursor NO/OFF (C), and blink of cursor position character (B). Moves the cursor and shifts the display without changing DD RAM contents. Sets interface data length (DL) number of display lines (L) and character font (F) Sets the CG RAM address. CG RAM data is sent and received after this setting. Sets the DD RAM address. DD RAM data is sent and received after this setting. Reads Busy flag (FB) indicating internal operation is being performed and reads address counter counts. Writes data into DD RAM or CG RAM. Reads data from DD RAM or CG RAM.

Executed Time(max.)
1.64mS 1.64mS 40 S 40 S 40 S 40 S 40 S 40 S 0 S 40 S 40 S

0 0 0 0 0 0 0 0 0 1 1

0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 1

0 0 0 0 0 0 1

0 0 0 0 0

0 0 0 0

1 1/D S
D C B

1 S/C R/L *
F

* *

1 DL N

ACG ADD AC WRITE DATA READ DATA

1 BF 0 1 Code

Descripion
DD RAM : Display Data RAM CG RAM : Character Generator RAM ACG : CG RAM Address ADD : DD RAM Address Corresponds to cursor address AC : Address Counter, used for both DD RAM and CG RAM * : Invalid

Executed Time (max)


fcp or fosc = 250 KHz However. when frequency changes. eecution time also changes Example if fcp or fosc is 270KHz, 70 S x 250 / 270 = 37 S

D / L = 0 : 4-bit I /D = 1 : Increment N = 1 : 2 lines I /D = 0 : Decrement N = 0 : 1 line S = 1 : With display shift S / C = 0 : cursor movement F = 1 : 5 x 10 dots F =0.5 x 7 dots R / L =1 : Shift to the right BF = 1 : internal operation is being R / L = 0 : Shift to the left performed D L = 1 : 8-bit BF = 0 : instruction acceptable

You might also like