Additional Strengtening of Superalloy Nimonic 80a by Worm Rolling

14th International Research/Expert Conference Trends in the Development of Machinery and Associated Technology TMT 2010, Mediterranean Cruise,
11-18 September 2010
ADDITIONAL STRENGTENING OF SUPERALLOY NIMONIC 80A BY WORM ROLLING

Omer Beganovi Mirsada Oru Milan Rimac University of Zenica - Institute of Metallurgy Kemal Kapetanovi Travnika cesta 7, Zenica Bosnia and Herzegovina Faik Uzunovi University of Zenica - Faculty of Metallurgy and Materials Science Travnika cesta 1 , Zenica Bosnia and Herzegovina
ABSTRACT Superalloy Nimonic 80A is regularly used in heat-treated condition. Heat treatment includes solution annealing at 1080oC/8h and precipitation aging at 700oC/16h. Maximal hardness that can be achieved after that treatment is around 360HV. For certain needs automotive industry requires the hardness of this superalloy to be more than 360HV. Taking into consideration the fact that during solution annealing the grains coarse significantly, it is not possible to achieve needed additional strengthening of superalloy Nimonic 80A by grain size control. In spite of that, additional strengthening is possible to achieve by controlled worm rolling of the superalloy, after performing its solution annealing and all is done, through partial recrystallization after worm rolling. Accordingly it is possible to control the hardness. Key words: superalloys, worm rolling, strengthening mechanisms 1. INTRODUCTION Superalloy Nimonic 80A is the alloy from series NIMONIC nickel-base superalloys that contain 20% of chromium [1]. It is intended for use at elevated and high temperatures at which the creep process occurs significantly. The primary strengthening mechanism of this superalloy is based on precipitation of fine and coherent particle of intermetallic phase Ni3(Al,Ti), which ensure needed creep strength. This strengthening mechanism for such superalloy is more favorable in relation to other strengthening mechanisms [2]. The effect of hardening that can be achieved by ' phase depends on amount, dispersion, and size of ' phase. All mentioned is controlled by heat treatment. Standard heat treatment includes solution annealing at 1080oC/8h and precipitation aging at 700oC/16h. Maximal hardness of the superalloy Nimonic 80A that can be achieved after this treatment is around 360HV, but for certain needs automotive industry requires higher hardness values. Since after long-lasting solution annealing at high temperature, the grains become coarse, it is not possible to increase the hardness (additional strengthening) significantly through reducing of the grain size. An increasing of the dislocation density, after solution annealing and before precipitation aging, through warm deformation, is effective way to increase the hardness of that superalloy. A partial recrystallization after such a deformation enables the hardness control.
613
2. EXPERIMENTAL RESULTS On the semi-industrial equipment of the Institute of Metalurgy Kemal Kapetanovi Zenica three experimental heats of the superalloy Nimonic 80A were produced and processed to the 15mm bars. The heats were produced in 20kg vacuum induction furnace. Chemical composition of all heats is shown in Table 1. and satisfy requirements of standard ASTM B 637 for alloy N07080, since it allows that content of aluminum may be less than 1,0% - variant I. Aluminum content in variants II and III is higher then 1,0%, so these two variants, according to chemical composition, satisfy requirements of the other standards defining chemical composition of the superalloy Nimonic 80A. Table 1. Chemical composition of experimental heats [3].
Content of elements in %
Variant C Variant I Variant II Variant III 0.04 0.05 0.04 Cr 18.8 19.7 20.8 Si 0.20 0.25 0.23 Mn 0.14 0.03 0.16 Fe 1.58 2.10 1.48 Co 1.20 1.25 1.30 S 0,006 0,007 0,006 P 0.004 0.005 0.005 Ti 2.28 2.52 2.68 Al 0.77 1.32 1.44 Balance Ni Al+Ti 3.05 3.84 4.12
Hot plastic deformation of all variants were performed on hydraulic press capacity 2.0MN, pneumatic hammer capacity 2.5kN, and the light section rolling mill 370 mm in temperature interval 9501170oC. After hot plastic deformation different bars for each variant were obtained (Figure 1.). The bars with diameter 15 mm are intended for determining of the superalloy mechanical properties in standard heat-treated condition, and the others for controlled rolling with different amount of deformation.
Variant I Initial oval 13 x 25 Vertical oval 14,5 x 19 Preparatory oval for the final pass 12 x 20,5 Variant II Variant III 30% worm deformation to 15 mm 20% worm deformation to 15 mm 10% worm deformation to 15 mm Without worm deformation
15 mm
Figure 1. Cross section of the bars after hot rolling influence on the recrystallization temperature [3].
All hot rolled bars were subjected to solution annealing at 1080oC/8h, and then bars, except those with diameter 15mm, were rolled to the same diameter (15mm) with 10, 20 or 30% of worm deformation. The starting temperature for controlled rolling was 1080oC in the case of the variants II and III, but in the case of variant I, the starting temperature was 1040oC, because of preliminary research, which showed that recrystallization temperature of the variant I bars is significantly lower in comparison to the temperature of variants II and III bars. Also the preliminary research showed that aluminum and titanium have determinative
After controlled rolling all bars were subjected to recrystallization on different temperatures (960oC, 1000oC and 1040oC) in duration of one or two hours. At the end all bars were subjected to precipitation aging at 700oC/16h in order to perform hardness and tensile testing in precipitation aged state. All thermal and thermomechanical treatments were carried out on the bars from all chemical composition variants, and are shown in Figure 2.
614
Variants I, II, III
Variant I
Variants II, III
Variants I, II, III
Temperature
1080oC/8h
1040oC/5min
1080oC/5min 960 C 1h 2h
o
1000oC 1h 2h
1040oC 1h 2h
700oC/16h Solution annealing Precipitation aging
Controlled rolling
Each pass by 10% deformation
Recrystallization annealing
Figure 2. Controlled rolling in combination with corresponding heat treatments As a result of lower content of aluminium and titanium the bars of variant I chemical compiosition show lower hardness values and lower recrystallization temperature in comparison to the bars of the variants II and III (Table 2.). Taking into account the fact that the recrystallization temperature of the variant I is less than 960oC, it means that through recrystallization annealing is not possible to achieve the hardness of the variat I bars to be higher than 360HV, because the temperature of ' phase precipitation of Nimonic 80A is around 960oC. For the difference to that variant, the hardness of variant II and III bars can be controlled through a partial recrystallization. Table 2. Hardness (HV10) of the bars after corresponding treatments including final precipitation aging (700oC/16h)
Variant Solution anneal. 1080oC/8h Worm def. (%) 10 298 20 30 10 352 20 30 10 361 20 30 Solution anneal. + worm def. 366 401 405 462 443 471 416 460 473 Solution anneal. 1080oC/8h + worm def. + recrystallization anneal. 960oC 1h 298 299 296 403 431 442 422 434 438 960oC 2h 299 299 295 402 429 442 401 430 446 1000oC 1h 298 297 297 403 431 416 393 431 420 1000oC 2h 296 294 296 393 394 359 392 414 421 1040oC 1h 283 285 286 355 356 358 369 371 372 1040oC 2h 294 295 293 352 353 353 356 356 355
Variant I
Variant II
Variant III
The results of tensile testing at room temperature of the bars with a different thermo-mechanical treatments are presented in Table 3. The worm deformation causes a significant increase of the strength, but also a significant decrease in ductile properties, especially in the case of bars of the variant II and III. The partial recrystallization of the specific bars (variant II-1000oC/1h, variant III1020oC/1h) results in a significant increase in ductile properties and retaining of the strength ones.
615
3. CONCLUSION Aluminium and titanium show the most significant influence on mechanical properties and recrystallization temperature of the superalloy Nimonic 80A. Its hardness and strength can be significantly increased through worm deformation carried out after the solution annealing. By the subsequent partial recrystallization annealing the values of hardness and tensile properties of the alloy can be controlled. For that reason it is needed that the alloy contains high enough content of aluminium and titanium, so that the recommended partial recrystallization temperature should be higher than solvus temperature of the ' phase. Otherwise the precipitation of the ' phase will appear, and as a result of that it will decrease the effect of precipitation strengthening as the primary strengthening mechanism of the superalloy Nimonic 80A. Table 3. Tensile test results at room temperature (The mean value of the two test pieces)
Variant Order number 1. I 2. 1. 2. II 3. 4. 1. III 2. 3. 970 1008 731 1027 1051 1242 1315 1122 1151 1291 1,28 1,30 1,53 1,12 1,23 18,5 18,0 29,6 9,6 17,3 31,5 26,5 38,0 14,0 22,0 923 745 1011 1134 1143 1233 1,23 1,53 1,22 21,4 29,7 11,5 42,5 39,0 17,0 Rp0,2 (MPa) 565 Rm (MPa) 977 Rm/ Rp0,2 1,73 A
1)
Z (%) 41,5
(%) 39,5
Treatment
1080oC/8h +700oC/16h 1080oC/8h+20%worm def. +700oC/16h 1080oC/8h +700oC/16h 1080oC/8h+10%worm def.+ 1000oC/1h +700oC/16h 1080oC/8h+20%worm def.+ 1000oC/1h +700oC/16h 1080oC/8h+30%worm def.+ 1000oC/1h +700oC/16h 1080oC/8h +700oC/16h 1080oC/8h+20%worm def.+ 1000oC/1h +700oC/16h 1080oC/8h+20%worm def.+ 1020oC/1h +700oC/16h
Note: 1) Tests were carried out on test pieces with nominal diameter D= 7,5 mm and original gage length L0=30mm, so the testing results are related to 4D.
4. REFERENCES
[1] Betteridge W., Heslop J.: The Nimonic Alloys and Other Nickel- Base High-Temperature Alloys, Sec. Ed., Edward Arnold (Publishers) Limited, London 1974., [2] Threadgill P.L., Wilshire B.: Mechanisms of transient and steady-state creep in a -hardened austenitic steel, Proceedings of meeting on Creep strength in the steel and high-temperature alloys, The Metal Society, London 1974., [3] Beganovi O., Muminovi B., Faki B., Uzunovi F.: Uticaj aluminija i titana na temperaturu rekristalizacije superlegure Nimonic 80A, VIII Nauno/struni simpozij sa meunarodnim ueem, Metalni i nemetalni materijali BiH, Zenica 2010.
616

Additional Strengtening of Superalloy Nimonic 80a by Worm Rolling

Uploaded by

Copyright:

Available Formats

Additional Strengtening of Superalloy Nimonic 80a by Worm Rolling

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Additional Strengtening of Superalloy Nimonic 80a by Worm Rolling

Uploaded by

Copyright:

Available Formats

14th International Research/Expert Conference Trends in the Development of Machinery and Associated Technology TMT 2010, Mediterranean Cruise,

11-18 September 2010

ADDITIONAL STRENGTENING OF SUPERALLOY NIMONIC 80A BY WORM ROLLING

Variants I, II, III

Variants II, III

Variants I, II, III

700oC/16h Solution annealing Precipitation aging

You might also like