CH - 5N11 (Z - S3P8849, NN5198, STR6656) - Service Adjustments
CH - 5N11 (Z - S3P8849, NN5198, STR6656) - Service Adjustments
CH - 5N11 (Z - S3P8849, NN5198, STR6656) - Service Adjustments
CHASSIS ADJUSTMENT
EEPROM partial initializing
1-1 Go to the function set menu (there are two ways;) A. Press VOL+ key and VOL- key on the control board at the same time and switch on power switch, then press" menu" key to go to the' Option Code t' menu. In this menu, it shows: 12 3 4 5 6 7 8 9 A (RED CO LOR ) * * * * * * * * * * (GR EEN C OLO R) B. After TV is on, press "factory" key (See Note 1) then press " menu" key until there show ten numbers on the center of the screen(Option Code menu). 1-2 Press 'PM' key and 'SM ' key on the control board at the same time until the" INITIAL PART OK " apears, this means the memory having been partially initialized. Operate repeatedly if the picture has no change. All of the TV set EEPROM must be partially initialized before exfactory or after change of the Chroma IC NN5198 / NN5199 or fully EEPROM initialized after change of the EEPROM 24C04(OR 24C08,24C16,Note 4).
FOCUS Adjustment
4-1 Receive PAL system cross hatch pattern signal; 4-2 Press 'factory' key one time, go to system parameter adjustment menu; 4-3 Press 'MENU' key, go to horizontal and vertical parameter adjustment menu; 4-4 Select 'V LINE' and 'V SCURVE' by pressing 'PROG+' key and 'PROG-' key; press 'VOL+' key and 'VOL-' key and adjust Corresponding parameter to obtain picture's vertical pin cushion a good status.
White Balance Adjustment(Applied servicing) FOCUS Adjustment PAL system vertical size and verticalwhen center adjustemt
5-1 Continue operation 3. Select 'V AMP" and 'V POSITION', press 'VOL+' key and 'VOL-' key adjust corresponding parameter to obtain picture's vertical size and vertical center adjustment a good status. 5-2 Exit system parameter adjustment menu by pressing 'factory' key.
-18-
Service Adjustments
White Balance adjustment
For Factory Auto Computer adjustment 6-1 Receive white balance test signal; 6-2 Set picture "SOFT" mode. 6-3 Insert the special plug into CN002, press adjustment key which belongs to white balance adjustment equipment and go to auto white balance adjustment; 6-4 After adjustment well, remove the pug. For Factory Manual adjustment 6-5 Press 'factory' key one time and go to system parameter adjustment menu; 6-5 Press "MENU" key oncethen go to the White Balance adjustment menu; 6-6 Press 'Prog +' key and 'Prog -' key to select the R, G, B cutoff and R, B Driver. 6-7 Press 'VOL+' key and 'VOL-' key to change. Or using the below direct key 6-8 SEC-R and SEC-B are prepared for SECAM system White Balance. 6-9 Key: 0 for SUB-BRIGHT, 1 for CUTOFF-R, 2 for CUTOFF-G, 3 for CUTOFF-B, 4 for DRIVER-R, 5 for DRIVER-B Recall for toggle the SubBright adjustment (Min. contrast, some CPU version is not work)
Sub-bright adjustement
7-1 Receive PHILIPS signal; 7-2 Set picture "RICH" mode. 7-3 Press 'factory' key one time and go to system parameter adjustment menu; 7-4 Press digital key '0', select 'SUB-BRIGHT'; 7-5 Press 'VOL+' key and 'VOL-' key until Grey scale signal can be secerned; 7-6 Exit system parameter adjustment menu by pressing 'factory' key twin.
R F AGC adjustment
8-1 8-2 8-3 8-4 8-5 Receive 60dBuV monoscope pattern; Press 'factory' key one time and go to system parameter adjustment menu; Press 'PROG+' key and 'PROG-' key , select ' RF AGC '; Press 'VOL+' key and 'VOL-' key to change the value of 'RF AGC ' until picture's noise disturbing disappears just; Exit system parameter adjustment menu by pressing 'factory' key.
Warm up mode
10- 1Press" factory" key(see note 1) to enter warm up mode, at this time there is no signal white raster and won't switch Off automatically. TV receiver can be sent to warm up line. 10-2 Before exit warm up line, press "factory" key, at this time exit warm up mode , there is no signal and will appear LOGO pattern.
-19-
Service Adjustments
NOTES:
1. Connect the remote IC PIN11 and PIN27 through a jiggle switch on the USER remote handset , this switch is defined as "screen" key; Connect the remote IC PIN14 and PIN27 through a jiggle switch on the USER remote handset , this Witch is defined as "factory" key; On the product line's alignment service we must use special memorizer that has been well written data. 2. If having no special memorizer that has been well written data when servicing out of factory, we can use blank new EEPROM. EEPROM will be automatically totally initialized after main power switch is on. Most parameters are free-alignment after initialized; only need adjust the several parameters of function set parameter and system parameter adjustment menu. 3 . If no blank new EEPROM or no special memorizer that has been well written data, we can use memorizer that has been written data instead, but must be totally initialized; the operation is as following: 1).After TV is on, press "factory" key twinthen go to the function set menu; 2).Press 'AV/TV' key and 'P.M' key on the control board,the TV turns off automatically; this means the memory having been totally initialized. Operate repeatedly if the picture has no change; 3).Switch off and exit; 4).After initialized, adjust the several parameters of function set parameter and system parameter adjustment Menu. 4. the parameters of function set parameter and system parameter adjustment menu mustn't be adjusted; 1).system parameter adjustment menu (This is coming from the NN5198/ NN5199) AFT VIF VCO H VCO VIFDET NEG VIFDET INT VIFDET EXT 2).the ninth digital and the tenth digital of function set parameter These parameters must be IC interior values. If the above parameters have been changed, we must partially initialize the EEPROM. 5. Two different initializing 1).fully initialize: initialize the EEPROM's most work data and preset default value. Including: work parameter of NN5199, horizontal and vertical parameter, OPTION parameter (via. function set parameter), picture mode parameter, volume mode parameter and white balance parameter. 2).partially initialize: only initialize work parameter of NN5199 and the ninth digital and the tenth digital of function set parameter(via. ISUD0, ISUD1,ISUD3,ISUD4,ISUD5),preset as interior values. 6. If use 25" or above Pure Flat tube , must adjust horizontal size and pincushion distortion as following: 1).Receive 60dBuV PAL system monoscope pattern; 2).Press 'factory' key one time and go to system parameter adjustment menu; 3).Press 'MENU' key and select ' Position Menu ' as below V POSITION for adjust vertical position 00 to 07 H POSITION for adjust Horizontal position 00 to 1F Warm upVmode EHT for adjust vertical shape 00 to 0F H EHT for adjust Horizontal shape 00 to 0F 4).Press 'MENU' key and select ' geometry Menu ' as below; V-AMP for adjust vertical size 00 to 7F . V_LINE for adjust vertical linearity 00 to 3F. V_SC3 for adjust vertical S-correction X3 00 to 3F. H-AMP for adjust Horizontal size 00 to 3F. EW-PARA for adjust Pincushion 00 to 3F. EW-COR for adjust Pincushion corner 00 to 0F. TRAPEZ for adjust trapezium 00 to 3F. V_SC5 for adjust vertical S-correction X5 00 to 0F. 5).Receive 60dBuV NTSC system monoscope pattern; 5.1 Repeat the above step 7.2 to 7.4. 6).Exit system parameter adjustment menu by pressing 'factory' key twin 7. Option Code 1).Press 'factory' key and go to Option Code Menu
-20-
Service Adjustments
123456789A 13714046**
The first Balance digit 8 Digit is setadjustment by Factory. The last two digit White "9 " and "A " is the random data from NN5198/NN5199. OPTION 1 (Sopdata1)(number 1 and 2) x x x x |x x x x ---> Sharp Peak frequency 3/4Mhz (0/1) (For NN5198) | | | | | | +------> SuperWoofer sound setting ON/OFF | | | | | +--------> RGB limit ON/OFF | | | | +----------> Reserved for internal using, must be zero | | | +------------> Ntsc decoder ON/OFF (include 3.58 & 4.43) | | +--------------> Secam decoder ON/OFF | +----------------> YUV ON/OFF +------------------> NTSC QSS
OPTION 2 (Sopdata2)(number 3 and 4) x x x x| x x x x ---> Two av source only | | | | | | +------> Three av source | | | | | +--------> S-video source support | | | | +----------> Reserved for internal using, must be zero | | | +------------> M decoder ON/OFF | | +--------------> I decoder ON/OFF | +----------------> BG decoder ON/OFF +------------------> Reserved for internal using, must be zero OPTION 3 (Sopdata3) x x x x x x x x --- > Tune r LNA | | | | | | +------> Hold on when no signal | | | | | +--------> VIF VCO 38MHz or 38.9MHz selection | | | | +----------> Reserved for internal using, must be zero | | | +------------> Game avaliable | | +--------------> Gamma Correction ON/OFF (0/1) (For NN5198) | +----------------> RGB Gain 0.56/0.83 (0/1) (For NN5198) +------------------> Reserved for internal using, must be zero OPTION 4 (Sopdata4)(number 7 and 8) x x x x |x x x x ---> Multi-language OSD ON/OFF | | | | | | +------> LOGO enable ON/OFF up mode | | | | | +--------> LOGO define ON/OFF | | | | +----------> Reserved for internal using, must be zero | | | +------------> BBE sound ON/OFF | | +--------------> QSS sw ON/OFF | +----------------> SIF Internal/External (1/0) (For NN5198) +------------------> Reserved for internal using, must be zero OPTION 5 (Dwork3 )(number 9 and A) x x x x |x x x x -- -> IS UD0 | | | | | | +------> ISUD1 | | | | | +--------> PAL_M/N ON/OFF | | | | +----------> Reserved for internal using, must be zero | | | +------------> ISUD3 | | +--------------> ISUD4 | +----------------> ISUD5 +------------------> Reserved for internal using, must be zero
Warm
-21-
CONVERGENCE ADJUSTMENT
(1) Receive a dotted pattern. Set the TV receiver dynamic. (2) Loose the convergence magnet clamperrrrr and align red with blu dots at the center of the screen by rotating(R,B) static convergence magnets. (3) Align Red/Blue with green dots at the center of the screen by rotating(RB-G) static convergence magnet. (4) Remove the DY wedges and slightly tilt the deflection yoke horizontally and vertically to obtain the good
Static Magnet
-22-